#	$NetBSD: GENERIC3X,v 1.7 1997/05/07 02:20:27 lukem Exp $
#
# GENERIC Sun3x (3/80, 3/470)
# Supports root on: le0, sd*
#

include "arch/sun3x/conf/std.sun3x"

# Machines to be supported by this kernel
# options 	FPU_EMULATE		# XXX - Ever needed?

# Needs to be set per system.  i.e change these as you see fit
maxusers	4

# Standard system options
options 	KTRACE			# system call tracing support

# Debugging options.  Uncomment either these:
options 	DDB
#options 	SYMTAB_SPACE=0x1C000
# ... or these for KGDB (gdb remote target)
#makeoptions DEBUG="-g"		# debugging symbols for gdb
#options 	KGDB
#options 	KGDBDEV=0x0C01	# ttya=0C00 ttyb=0C01

# Filesystem options
file-system	FFS		# ufs file system
file-system	NFS		# nfs client support
file-system	CD9660		# ISO 9660 + Rock Ridge file system
file-system	MSDOSFS		# MS-DOS FAT file system
file-system	FDESC		# /dev/fd/*
file-system	KERNFS		# /kern
file-system	NULLFS		# loopback file system
file-system	PROCFS		# /proc
file-system	UNION		# union file system
file-system	MFS		# memory-based filesystem

options 	NFSSERVER	# nfs server support
options 	FIFO		# FIFOs; RECOMMENDED

# Networking options
options 	INET		# IP prototol stack support
#options 	GATEWAY		# IP packet forwarding
options 	TCP_COMPAT_42	# TCP bug compatibility with 4.2BSD
# XXX - Work-around for root on slow servers (insurance...)
options 	NFS_BOOT_RWSIZE=1024

# Compatability options
options 	COMPAT_SUNOS	# can run SunOS 4.1.1 executables
options 	COMPAT_43	# and 4.3BSD and ...
options 	COMPAT_12	# NetBSD 1.2
options 	UCONSOLE	# Allow non-root TIOCCONS

# Sun3x-specific debugging options
#options 	PMAP_DEBUG
#options 	VMFAULT_TRACE
#options 	SYSCALL_DEBUG
#options 	EXEC_DEBUG
#options 	DIAGNOSTIC
#options 	SCSIDEBUG

config		netbsd root on ? type ?

#
# Serial ports
#
zstty0 at zsc1 channel 0	# ttya
zstty1 at zsc1 channel 1	# ttyb

kbd0   at zsc0 channel 0	# keyboard
ms0    at zsc0 channel 1	# mouse

#
# Network devices
#

# Lance Ethernet (only onboard)
le0 at obio0 addr 0x65002000 ipl 3

#
# Disk and tape devices
#

# Note the flags on the esp entries below, that work around
# deficiencies in the current driver:
#	bits 0-7:  disable disconnect/reselect for the corresponding target
#	bits 8-15: disable synch negotiation for target [bit-8]
#	Note: targets 4-7 have disconnect/reselect enabled on the premise
#	      that tape devices normally have one of these targets. Tape
#	      devices should be allowed to disconnect for the SCSI bus
#	      to operate acceptably.
#
# Emulex SCSI (3/80 only)
esp0 at obio0 addr 0x66000000 ipl 2 flags 0xff0f

# Floppy drive
fdc0 at obio0 addr 0x6e000000 ipl 6 vect 0x40
fd0  at fdc0	# First (and only) floppy drive.

#
# Frame buffer devices
#

# bwtwo - Monochrome frame buffer.
bwtwo0 at obmem0 addr 0x50400000 ipl 4

#
# SCSI infrastructure
#
scsibus* at scsi?

sd* at scsibus? target ? lun ?		# SCSI disks
st* at scsibus? target ? lun ?		# SCSI tapes
cd* at scsibus? target ? lun ?		# SCSI CD-ROMs
ch* at scsibus? target ? lun ?		# SCSI changer devices
ss* at scsibus? target ? lun ?		# SCSI scanners
uk* at scsibus? target ? lun ?		# unknown SCSI devices

# Memory-disk drivers
pseudo-device	md		2

# Misc.
pseudo-device	loop		1	# network loopback
pseudo-device	bpfilter	8	# packet filter
pseudo-device	sl		2	# CSLIP
pseudo-device	ppp		2	# PPP
pseudo-device	tun		2	# network tunneling over tty
#pseudo-device	ipfilter		# ip filter

pseudo-device	pty		64	# pseudo-terminals
#pseudo-device	vnd		4	# paging to files
#pseudo-device	ccd		4	# concatenated disks