The LLVM build is a bit larger than the GCC build. Bump the size up a bit.

Make the sshramdisk a bit bigger. Hopefully fixes the build.

use IMAGESPECEXTRA to include libdata and don't include IMAGERUNTIME

use IMAGERUNTIME to copy extra data instead of random pax commands

evbarm/instkernel/sshramdisk: Put firmware in the right paths.

Maybe this should also be wired up to `release' to put the ramdisk in
the releasedir so we detect destdir path leakage like this had.

PR port-evbarm/58035

branches: 1.25.6;
Bump IMAGESIZE

Bump image size - new firmware files need more space

Redo the sshsk_sign() stuff properly, but putting the helper in libssh.so

Deal with sshkey_sign. I am going to fix this properly at some point, but
it needs coordination from upstream (Patrick Welche)

Was too slight a bump.

Bump image size slightly

Bump image size for gcc8

Update to newer sshd (the host key is the same as before, it already
was a rsa key). From Harold Gutch.

branches: 1.17.2; 1.17.4;
increase sshramdisk from 24000k to 28000k.

branches: 1.16.2;
Bump image size to 24MB, won't fit for plain evbarm otherwise.

branches: 1.15.4;
Bump image size to unbreak builds.
nbmakefs: `work' size of 21610496 is larger than the maxsize of 20480000.

ok jakllsch

fix typo.

more MKREPRO_TIMESTAMP fixes (for pax/tar generated files)

+= for MAKEFS_FLAGS

branches: 1.11.2;
give it a bit more room.

grow so that new intel firmware fits.

branches: 1.9.2;
Set IMAGEENDIAN properly for big endian builds.
From Rin Okuyama.

Give LLVM a bit breathing room for the sshramdisk when building for
generic ARM.

Bump size to fix build.

Bump image size to compensate new iwn(4) firmwares.

LLVM sshramdisk needs 8.9MB, so bump again.

Add firmware images to this image, as discussed on port-arm.

branches: 1.3.4; 1.3.6;
Bump sshramdisk size to 3800k, reserve 4MB in the install kernel.

Bump imagesize to fix build.

branches: 1.1.6;
Add a new installer image for Raspberry PI to evbarm

Includes the following major changes:

1) Add new configmenu item to sysinst to allow creation of users at
post-install time.
2) Add an sshramdisk type to evbarm, which is a ramdisk with sshd
enabled, allowing users to install on a headless PI by sshing to the
device with the account "sysinst" password "netbsd" to begin the
installation. (Note, neither the account, nor the ssh setup are copied to
the finalized installation image)
3) Change mkimage to build a boot-only image, without the root filesystems.

Much of the sshramdisk code could be reused on other ports easily.

Make the sshramdisk a bit bigger. Hopefully fixes the build.

use IMAGESPECEXTRA to include libdata and don't include IMAGERUNTIME

use IMAGERUNTIME to copy extra data instead of random pax commands

evbarm/instkernel/sshramdisk: Put firmware in the right paths.

Maybe this should also be wired up to `release' to put the ramdisk in
the releasedir so we detect destdir path leakage like this had.

PR port-evbarm/58035

branches: 1.25.6;
Bump IMAGESIZE

Bump image size - new firmware files need more space

Redo the sshsk_sign() stuff properly, but putting the helper in libssh.so

Deal with sshkey_sign. I am going to fix this properly at some point, but
it needs coordination from upstream (Patrick Welche)

Was too slight a bump.

Bump image size slightly

Bump image size for gcc8

Update to newer sshd (the host key is the same as before, it already
was a rsa key). From Harold Gutch.

branches: 1.17.2; 1.17.4;
increase sshramdisk from 24000k to 28000k.

branches: 1.16.2;
Bump image size to 24MB, won't fit for plain evbarm otherwise.

branches: 1.15.4;
Bump image size to unbreak builds.
nbmakefs: `work' size of 21610496 is larger than the maxsize of 20480000.

ok jakllsch

fix typo.

more MKREPRO_TIMESTAMP fixes (for pax/tar generated files)

+= for MAKEFS_FLAGS

branches: 1.11.2;
give it a bit more room.

grow so that new intel firmware fits.

branches: 1.9.2;
Set IMAGEENDIAN properly for big endian builds.
From Rin Okuyama.

Give LLVM a bit breathing room for the sshramdisk when building for
generic ARM.

Bump size to fix build.

Bump image size to compensate new iwn(4) firmwares.

LLVM sshramdisk needs 8.9MB, so bump again.

Add firmware images to this image, as discussed on port-arm.

branches: 1.3.4; 1.3.6;
Bump sshramdisk size to 3800k, reserve 4MB in the install kernel.

Bump imagesize to fix build.

branches: 1.1.6;
Add a new installer image for Raspberry PI to evbarm

Includes the following major changes:

1) Add new configmenu item to sysinst to allow creation of users at
post-install time.
2) Add an sshramdisk type to evbarm, which is a ramdisk with sshd
enabled, allowing users to install on a headless PI by sshing to the
device with the account "sysinst" password "netbsd" to begin the
installation. (Note, neither the account, nor the ssh setup are copied to
the finalized installation image)
3) Change mkimage to build a boot-only image, without the root filesystems.

Much of the sshramdisk code could be reused on other ports easily.