1 /* $NetBSD: seeq8005.c,v 1.66 2020/01/30 04:56:11 thorpej Exp $ */ 2 3 /* 4 * Copyright (c) 2000, 2001 Ben Harris 5 * Copyright (c) 1995-1998 Mark Brinicombe 6 * All rights reserved. 7 * 8 * Redistribution and use in source and binary forms, with or without 9 * modification, are permitted provided that the following conditions 10 * are met: 11 * 1. Redistributions of source code must retain the above copyright 12 * notice, this list of conditions and the following disclaimer. 13 * 2. Redistributions in binary form must reproduce the above copyright 14 * notice, this list of conditions and the following disclaimer in the 15 * documentation and/or other materials provided with the distribution. 16 * 3. All advertising materials mentioning features or use of this software 17 * must display the following acknowledgement: 18 * This product includes software developed by Mark Brinicombe 19 * for the NetBSD Project. 20 * 4. The name of the company nor the name of the author may be used to 21 * endorse or promote products derived from this software without specific 22 * prior written permission. 23 * 24 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED 25 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF 26 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 27 * IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, 28 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES 29 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 30 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 31 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 32 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 33 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 34 * SUCH DAMAGE. 35 */ 36 /* 37 * seeq8005.c - SEEQ 8005 device driver 38 */ 39 /* 40 * This driver currently supports the following chips: 41 * SEEQ 8005 Advanced Ethernet Data Link Controller 42 * SEEQ 80C04 Ethernet Data Link Controller 43 * SEEQ 80C04A AutoDUPLEX CMOS Ethernet Data Link Controller 44 */ 45 /* 46 * More information on the 8004 and 8005 AEDLC controllers can be found in 47 * the SEEQ Technology Inc 1992 Data Comm Devices data book. 48 * 49 * This data book may no longer be available as these are rather old chips 50 * (1991 - 1993) 51 */ 52 /* 53 * This driver is based on the arm32 ea(4) driver, hence the names of many 54 * of the functions. 55 */ 56 /* 57 * Bugs/possible improvements: 58 * - Does not currently support DMA 59 * - Does not transmit multiple packets in one go 60 * - Does not support 8-bit busses 61 */ 62 63 #include <sys/cdefs.h> 64 __KERNEL_RCSID(0, "$NetBSD: seeq8005.c,v 1.66 2020/01/30 04:56:11 thorpej Exp $"); 65 66 #include <sys/param.h> 67 #include <sys/systm.h> 68 #include <sys/endian.h> 69 #include <sys/errno.h> 70 #include <sys/ioctl.h> 71 #include <sys/mbuf.h> 72 #include <sys/socket.h> 73 #include <sys/syslog.h> 74 #include <sys/device.h> 75 76 #include <net/if.h> 77 #include <net/if_dl.h> 78 #include <net/if_types.h> 79 #include <net/if_ether.h> 80 #include <net/if_media.h> 81 #include <net/bpf.h> 82 83 #include <sys/rndsource.h> 84 85 #include <sys/bus.h> 86 #include <sys/intr.h> 87 88 #include <dev/ic/seeq8005reg.h> 89 #include <dev/ic/seeq8005var.h> 90 91 /*#define SEEQ_DEBUG*/ 92 93 /* for debugging convenience */ 94 #ifdef SEEQ8005_DEBUG 95 #define SEEQ_DEBUG_MISC 1 96 #define SEEQ_DEBUG_TX 2 97 #define SEEQ_DEBUG_RX 4 98 #define SEEQ_DEBUG_PKT 8 99 #define SEEQ_DEBUG_TXINT 16 100 #define SEEQ_DEBUG_RXINT 32 101 int seeq8005_debug = 0; 102 #define DPRINTF(f, x) { if (seeq8005_debug & (f)) printf x; } 103 #else 104 #define DPRINTF(f, x) 105 #endif 106 107 #ifndef EA_TX_BUFFER_SIZE 108 #define EA_TX_BUFFER_SIZE 0x800 /* (> ETHER_MAX_LEN) */ 109 #endif 110 #ifndef EA_TX_BUFFER_COUNT 111 #define EA_TX_BUFFER_COUNT 1 /* (> 0) */ 112 #endif 113 114 #define SEEQ_READ16(sc, iot, ioh, reg) \ 115 ((sc)->sc_flags & SF_8BIT ? \ 116 (bus_space_read_1((iot), (ioh), (reg)) | \ 117 (bus_space_read_1((iot), (ioh), (reg) + 1) << 8)) : \ 118 (bus_space_read_2((iot), (ioh), (reg)))) 119 120 #define SEEQ_WRITE16(sc, iot, ioh, reg, val) do { \ 121 if ((sc)->sc_flags & SF_8BIT) { \ 122 bus_space_write_1((iot), (ioh), (reg), (val) & 0xff); \ 123 bus_space_write_1((iot), (ioh), (reg) + 1, (val) >> 8); \ 124 } else \ 125 bus_space_write_2((iot), (ioh), (reg), (val)); \ 126 } while (/*CONSTCOND*/0) 127 128 /* 129 * prototypes 130 */ 131 132 static int ea_init(struct ifnet *); 133 static int ea_ioctl(struct ifnet *, u_long, void *); 134 static void ea_start(struct ifnet *); 135 static void ea_watchdog(struct ifnet *); 136 static void ea_chipreset(struct seeq8005_softc *); 137 static void ea_ramtest(struct seeq8005_softc *); 138 static int ea_stoptx(struct seeq8005_softc *); 139 static int ea_stoprx(struct seeq8005_softc *); 140 static void ea_stop(struct ifnet *, int); 141 static void ea_await_fifo_empty(struct seeq8005_softc *); 142 static void ea_await_fifo_full(struct seeq8005_softc *); 143 static void ea_writebuf(struct seeq8005_softc *, u_char *, int, size_t); 144 static void ea_readbuf(struct seeq8005_softc *, u_char *, int, size_t); 145 static void ea_select_buffer(struct seeq8005_softc *, int); 146 static void ea_set_address(struct seeq8005_softc *, int, const uint8_t *); 147 static void ea_read(struct seeq8005_softc *, int, int); 148 static struct mbuf *ea_get(struct seeq8005_softc *, int, int, struct ifnet *); 149 static void ea_txint(struct seeq8005_softc *); 150 static void ea_rxint(struct seeq8005_softc *); 151 static void ea_txpacket(struct seeq8005_softc *); 152 static int ea_writembuf(struct seeq8005_softc *, struct mbuf *, int); 153 static void ea_mc_reset(struct seeq8005_softc *); 154 static void ea_mc_reset_8004(struct seeq8005_softc *); 155 static void ea_mc_reset_8005(struct seeq8005_softc *); 156 static int ea_mediachange(struct ifnet *); 157 static void ea_mediastatus(struct ifnet *, struct ifmediareq *); 158 159 static u_char* padbuf = NULL; 160 161 162 /* 163 * Attach chip. 164 */ 165 166 void 167 seeq8005_attach(struct seeq8005_softc *sc, const uint8_t *myaddr, int *media, 168 int nmedia, int defmedia) 169 { 170 device_t dev = sc->sc_dev; 171 struct ifnet *ifp = &sc->sc_ethercom.ec_if; 172 bus_space_tag_t iot = sc->sc_iot; 173 bus_space_handle_t ioh = sc->sc_ioh; 174 u_int id; 175 176 KASSERT(myaddr != NULL); 177 printf(" address %s", ether_sprintf(myaddr)); 178 179 /* Stop the board. */ 180 181 ea_chipreset(sc); 182 183 /* Work out data bus width. */ 184 SEEQ_WRITE16(sc, iot, ioh, SEEQ_RX_PTR, 0x1234); 185 if (SEEQ_READ16(sc, iot, ioh, SEEQ_RX_PTR) != 0x1234) { 186 /* Try 8-bit mode */ 187 sc->sc_flags |= SF_8BIT; 188 SEEQ_WRITE16(sc, iot, ioh, SEEQ_RX_PTR, 0x1234); 189 if (SEEQ_READ16(sc, iot, ioh, SEEQ_RX_PTR) != 0x1234) { 190 aprint_normal("\n"); 191 aprint_error_dev(dev, 192 "Cannot determine data bus width\n"); 193 return; 194 } 195 } 196 197 printf(", %d-bit", sc->sc_flags & SF_8BIT ? 8 : 16); 198 199 /* Get the product ID */ 200 201 ea_select_buffer(sc, SEEQ_BUFCODE_PRODUCTID); 202 id = SEEQ_READ16(sc, sc->sc_iot, sc->sc_ioh, SEEQ_BUFWIN); 203 204 switch (id & SEEQ_PRODUCTID_MASK) { 205 case SEEQ_PRODUCTID_8004: 206 sc->sc_variant = SEEQ_8004; 207 switch (id & SEEQ_PRODUCTID_REV_MASK) { 208 case SEEQ_PRODUCTID_REV_80C04: 209 printf(", SEEQ 80C04\n"); 210 break; 211 case SEEQ_PRODUCTID_REV_80C04A: 212 printf(", SEEQ 80C04A\n"); 213 break; 214 default: 215 /* Unknown SEEQ 8004 variants */ 216 printf(", SEEQ 8004 rev %x\n", 217 id & SEEQ_PRODUCTID_REV_MASK); 218 break; 219 } 220 break; 221 default: /* XXX */ 222 sc->sc_variant = SEEQ_8005; 223 printf(", SEEQ 8005\n"); 224 break; 225 } 226 227 /* Both the 8004 and 8005 are designed for 64K Buffer memory */ 228 sc->sc_buffersize = SEEQ_MAX_BUFFER_SIZE; 229 230 /* 231 * Set up tx and rx buffers. 232 * 233 * We set aside EA_TX_BUFFER_SIZE * EA_TX_BUFFER_COUNT for TX 234 * buffers and the rest for RX buffers 235 */ 236 sc->sc_tx_bufs = EA_TX_BUFFER_COUNT; 237 sc->sc_tx_bufsize = sc->sc_tx_bufs * EA_TX_BUFFER_SIZE; 238 sc->sc_rx_bufsize = sc->sc_buffersize - sc->sc_tx_bufsize; 239 sc->sc_enabled = 0; 240 241 /* Test the RAM */ 242 ea_ramtest(sc); 243 244 printf("%s: %dKB packet memory, txbuf=%dKB (%d buffers), rxbuf=%dKB", 245 device_xname(dev), sc->sc_buffersize >> 10, 246 sc->sc_tx_bufsize >> 10, sc->sc_tx_bufs, sc->sc_rx_bufsize >> 10); 247 248 if (padbuf == NULL) { 249 padbuf = malloc(ETHER_MIN_LEN - ETHER_CRC_LEN, M_DEVBUF, 250 M_ZERO | M_WAITOK); 251 } 252 253 /* Initialise ifnet structure. */ 254 255 strlcpy(ifp->if_xname, device_xname(dev), IFNAMSIZ); 256 ifp->if_softc = sc; 257 ifp->if_start = ea_start; 258 ifp->if_ioctl = ea_ioctl; 259 ifp->if_init = ea_init; 260 ifp->if_stop = ea_stop; 261 ifp->if_watchdog = ea_watchdog; 262 ifp->if_flags = IFF_BROADCAST | IFF_MULTICAST; 263 if (sc->sc_variant == SEEQ_8004) 264 ifp->if_flags |= IFF_SIMPLEX; 265 IFQ_SET_READY(&ifp->if_snd); 266 267 /* Initialize media goo. */ 268 ifmedia_init(&sc->sc_media, 0, ea_mediachange, ea_mediastatus); 269 if (media != NULL) { 270 int i; 271 272 for (i = 0; i < nmedia; i++) 273 ifmedia_add(&sc->sc_media, media[i], 0, NULL); 274 ifmedia_set(&sc->sc_media, defmedia); 275 } else { 276 ifmedia_add(&sc->sc_media, IFM_ETHER | IFM_MANUAL, 0, NULL); 277 ifmedia_set(&sc->sc_media, IFM_ETHER | IFM_MANUAL); 278 } 279 280 /* We can support 802.1Q VLAN-sized frames. */ 281 sc->sc_ethercom.ec_capabilities |= ETHERCAP_VLAN_MTU; 282 283 /* Now we can attach the interface. */ 284 285 if_attach(ifp); 286 ether_ifattach(ifp, myaddr); 287 288 printf("\n"); 289 290 /* After \n because it can print a line of its own. */ 291 rnd_attach_source(&sc->rnd_source, device_xname(dev), 292 RND_TYPE_NET, RND_FLAG_DEFAULT); 293 } 294 295 /* 296 * Media change callback. 297 */ 298 static int 299 ea_mediachange(struct ifnet *ifp) 300 { 301 struct seeq8005_softc *sc = ifp->if_softc; 302 303 if (sc->sc_mediachange) 304 return (*sc->sc_mediachange)(sc); 305 return EINVAL; 306 } 307 308 /* 309 * Media status callback. 310 */ 311 static void 312 ea_mediastatus(struct ifnet *ifp, struct ifmediareq *ifmr) 313 { 314 struct seeq8005_softc *sc = ifp->if_softc; 315 316 if (sc->sc_enabled == 0) { 317 ifmr->ifm_active = IFM_ETHER | IFM_NONE; 318 ifmr->ifm_status = 0; 319 return; 320 } 321 322 if (sc->sc_mediastatus) 323 (*sc->sc_mediastatus)(sc, ifmr); 324 } 325 326 /* 327 * Test the RAM on the ethernet card. 328 */ 329 330 void 331 ea_ramtest(struct seeq8005_softc *sc) 332 { 333 bus_space_tag_t iot = sc->sc_iot; 334 bus_space_handle_t ioh = sc->sc_ioh; 335 int loop; 336 u_int sum = 0; 337 338 /* 339 * Test the buffer memory on the board. 340 * Write simple pattens to it and read them back. 341 */ 342 343 /* Set up the whole buffer RAM for writing */ 344 345 ea_select_buffer(sc, SEEQ_BUFCODE_TX_EAP); 346 SEEQ_WRITE16(sc, iot, ioh, SEEQ_BUFWIN, (SEEQ_MAX_BUFFER_SIZE >> 8) - 1); 347 SEEQ_WRITE16(sc, iot, ioh, SEEQ_TX_PTR, 0x0000); 348 SEEQ_WRITE16(sc, iot, ioh, SEEQ_RX_PTR, SEEQ_MAX_BUFFER_SIZE - 2); 349 350 #define SEEQ_RAMTEST_LOOP(value) \ 351 do { \ 352 /* Set the write start address and write a pattern */ \ 353 ea_writebuf(sc, NULL, 0x0000, 0); \ 354 for (loop = 0; loop < SEEQ_MAX_BUFFER_SIZE; loop += 2) \ 355 SEEQ_WRITE16(sc, iot, ioh, SEEQ_BUFWIN, (value)); \ 356 \ 357 /* Set the read start address and verify the pattern */ \ 358 ea_readbuf(sc, NULL, 0x0000, 0); \ 359 for (loop = 0; loop < SEEQ_MAX_BUFFER_SIZE; loop += 2) \ 360 if (SEEQ_READ16(sc, iot, ioh, SEEQ_BUFWIN) != (value)) \ 361 ++sum; \ 362 } while (/*CONSTCOND*/0) 363 364 SEEQ_RAMTEST_LOOP(loop); 365 SEEQ_RAMTEST_LOOP(loop ^ (SEEQ_MAX_BUFFER_SIZE - 1)); 366 SEEQ_RAMTEST_LOOP(0xaa55); 367 SEEQ_RAMTEST_LOOP(0x55aa); 368 369 /* Report */ 370 371 if (sum > 0) 372 aprint_error_dev(sc->sc_dev, 373 "buffer RAM failed self test, %d faults\n", sum); 374 } 375 376 377 /* 378 * Stop the tx interface. 379 * 380 * Returns 0 if the tx was already stopped or 1 if it was active 381 */ 382 383 static int 384 ea_stoptx(struct seeq8005_softc *sc) 385 { 386 bus_space_tag_t iot = sc->sc_iot; 387 bus_space_handle_t ioh = sc->sc_ioh; 388 int timeout; 389 int status; 390 391 DPRINTF(SEEQ_DEBUG_TX, ("ea_stoptx()\n")); 392 393 sc->sc_enabled = 0; 394 395 status = SEEQ_READ16(sc, iot, ioh, SEEQ_STATUS); 396 if (!(status & SEEQ_STATUS_TX_ON)) 397 return 0; 398 399 /* Stop any tx and wait for confirmation */ 400 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, 401 sc->sc_command | SEEQ_CMD_TX_OFF); 402 403 timeout = 20000; 404 do { 405 status = SEEQ_READ16(sc, iot, ioh, SEEQ_STATUS); 406 delay(1); 407 } while ((status & SEEQ_STATUS_TX_ON) && --timeout > 0); 408 if (timeout == 0) 409 log(LOG_ERR, "%s: timeout waiting for tx termination\n", 410 device_xname(sc->sc_dev)); 411 412 /* Clear any pending tx interrupt */ 413 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, 414 sc->sc_command | SEEQ_CMD_TX_INTACK); 415 return 1; 416 } 417 418 419 /* 420 * Stop the rx interface. 421 * 422 * Returns 0 if the tx was already stopped or 1 if it was active 423 */ 424 425 static int 426 ea_stoprx(struct seeq8005_softc *sc) 427 { 428 bus_space_tag_t iot = sc->sc_iot; 429 bus_space_handle_t ioh = sc->sc_ioh; 430 int timeout; 431 int status; 432 433 DPRINTF(SEEQ_DEBUG_RX, ("ea_stoprx()\n")); 434 435 status = SEEQ_READ16(sc, iot, ioh, SEEQ_STATUS); 436 if (!(status & SEEQ_STATUS_RX_ON)) 437 return 0; 438 439 /* Stop any rx and wait for confirmation */ 440 441 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, 442 sc->sc_command | SEEQ_CMD_RX_OFF); 443 444 timeout = 20000; 445 do { 446 status = SEEQ_READ16(sc, iot, ioh, SEEQ_STATUS); 447 delay(1); 448 } while ((status & SEEQ_STATUS_RX_ON) && --timeout > 0); 449 if (timeout == 0) 450 log(LOG_ERR, "%s: timeout waiting for rx termination\n", 451 device_xname(sc->sc_dev)); 452 453 /* Clear any pending rx interrupt */ 454 455 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, 456 sc->sc_command | SEEQ_CMD_RX_INTACK); 457 return 1; 458 } 459 460 461 /* 462 * Stop interface. 463 * Stop all IO and shut the interface down 464 */ 465 466 /* ARGSUSED */ 467 static void 468 ea_stop(struct ifnet *ifp, int disable) 469 { 470 struct seeq8005_softc *sc = ifp->if_softc; 471 bus_space_tag_t iot = sc->sc_iot; 472 bus_space_handle_t ioh = sc->sc_ioh; 473 474 DPRINTF(SEEQ_DEBUG_MISC, ("ea_stop()\n")); 475 476 /* Stop all IO */ 477 ea_stoptx(sc); 478 ea_stoprx(sc); 479 480 /* Disable rx and tx interrupts */ 481 sc->sc_command &= ~(SEEQ_CMD_RX_INTEN | SEEQ_CMD_TX_INTEN); 482 483 /* Clear any pending interrupts */ 484 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, 485 sc->sc_command | SEEQ_CMD_RX_INTACK | SEEQ_CMD_TX_INTACK | 486 SEEQ_CMD_DMA_INTACK | SEEQ_CMD_BW_INTACK); 487 488 if (sc->sc_variant == SEEQ_8004) { 489 /* Put the chip to sleep */ 490 ea_select_buffer(sc, SEEQ_BUFCODE_CONFIG3); 491 SEEQ_WRITE16(sc, iot, ioh, SEEQ_BUFWIN, 492 sc->sc_config3 | SEEQ_CFG3_SLEEP); 493 } 494 495 /* Cancel any watchdog timer */ 496 sc->sc_ethercom.ec_if.if_timer = 0; 497 } 498 499 500 /* 501 * Reset the chip 502 * Following this the software registers are reset 503 */ 504 505 static void 506 ea_chipreset(struct seeq8005_softc *sc) 507 { 508 bus_space_tag_t iot = sc->sc_iot; 509 bus_space_handle_t ioh = sc->sc_ioh; 510 511 DPRINTF(SEEQ_DEBUG_MISC, ("ea_chipreset()\n")); 512 513 /* Reset the controller. Min of 4us delay here */ 514 515 /* 516 * This can be called before we know whether the chip is in 8- or 517 * 16-bit mode, so we do a reset in both modes. The 16-bit reset is 518 * harmless in 8-bit mode, so we do that second. 519 */ 520 521 /* In 16-bit mode, this will munge the PreamSelect bit. */ 522 bus_space_write_1(iot, ioh, SEEQ_CONFIG2 + 1, SEEQ_CFG2_RESET >> 8); 523 delay(4); 524 /* In 8-bit mode, this will zero the bottom half of config reg 2. */ 525 bus_space_write_2(iot, ioh, SEEQ_CONFIG2, SEEQ_CFG2_RESET); 526 delay(4); 527 528 sc->sc_command = 0; 529 sc->sc_config1 = 0; 530 sc->sc_config2 = 0; 531 sc->sc_config3 = 0; 532 } 533 534 535 /* 536 * If the DMA FIFO's in write mode, wait for it to empty. Needed when 537 * switching the FIFO from write to read. We also use it when changing 538 * the address for writes. 539 */ 540 static void 541 ea_await_fifo_empty(struct seeq8005_softc *sc) 542 { 543 bus_space_tag_t iot = sc->sc_iot; 544 bus_space_handle_t ioh = sc->sc_ioh; 545 int timeout; 546 547 timeout = 20000; 548 if ((SEEQ_READ16(sc, iot, ioh, SEEQ_STATUS) & 549 SEEQ_STATUS_FIFO_DIR) != 0) 550 return; /* FIFO is reading anyway. */ 551 while (--timeout > 0) 552 if (SEEQ_READ16(sc, iot, ioh, SEEQ_STATUS) & 553 SEEQ_STATUS_FIFO_EMPTY) 554 return; 555 log(LOG_ERR, "%s: DMA FIFO failed to empty\n", 556 device_xname(sc->sc_dev)); 557 } 558 559 /* 560 * Wait for the DMA FIFO to fill before reading from it. 561 */ 562 static void 563 ea_await_fifo_full(struct seeq8005_softc *sc) 564 { 565 bus_space_tag_t iot = sc->sc_iot; 566 bus_space_handle_t ioh = sc->sc_ioh; 567 int timeout; 568 569 timeout = 20000; 570 while (--timeout > 0) 571 if (SEEQ_READ16(sc, iot, ioh, SEEQ_STATUS) & 572 SEEQ_STATUS_FIFO_FULL) 573 return; 574 log(LOG_ERR, "%s: DMA FIFO failed to fill\n", device_xname(sc->sc_dev)); 575 } 576 577 /* 578 * write to the buffer memory on the interface 579 * 580 * The buffer address is set to ADDR. 581 * If len != 0 then data is copied from the address starting at buf 582 * to the interface buffer. 583 * BUF must be usable as a uint16_t *. 584 * If LEN is odd, it must be safe to overwrite one extra byte. 585 */ 586 587 static void 588 ea_writebuf(struct seeq8005_softc *sc, u_char *buf, int addr, size_t len) 589 { 590 bus_space_tag_t iot = sc->sc_iot; 591 bus_space_handle_t ioh = sc->sc_ioh; 592 593 DPRINTF(SEEQ_DEBUG_MISC, ("writebuf: st=%04x\n", 594 SEEQ_READ16(sc, iot, ioh, SEEQ_STATUS))); 595 596 #ifdef DIAGNOSTIC 597 if (__predict_false(!ALIGNED_POINTER(buf, uint16_t))) 598 panic("%s: unaligned writebuf", device_xname(sc->sc_dev)); 599 if (__predict_false(addr >= SEEQ_MAX_BUFFER_SIZE)) 600 panic("%s: writebuf out of range", device_xname(sc->sc_dev)); 601 #endif 602 603 if (addr != -1) { 604 ea_await_fifo_empty(sc); 605 606 ea_select_buffer(sc, SEEQ_BUFCODE_LOCAL_MEM); 607 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, 608 sc->sc_command | SEEQ_CMD_FIFO_WRITE); 609 610 ea_await_fifo_empty(sc); 611 612 SEEQ_WRITE16(sc, iot, ioh, SEEQ_DMA_ADDR, addr); 613 } 614 615 if (len > 0) { 616 if (sc->sc_flags & SF_8BIT) 617 bus_space_write_multi_1(iot, ioh, SEEQ_BUFWIN, 618 (uint8_t *)buf, len); 619 else 620 bus_space_write_multi_2(iot, ioh, SEEQ_BUFWIN, 621 /* LINTED: alignment checked above */ 622 (uint16_t *)buf, len / 2); 623 } 624 if (!(sc->sc_flags & SF_8BIT) && len % 2) { 625 /* Write the last byte */ 626 bus_space_write_2(iot, ioh, SEEQ_BUFWIN, buf[len - 1]); 627 } 628 /* Leave FIFO to empty in the background */ 629 } 630 631 632 /* 633 * read from the buffer memory on the interface 634 * 635 * The buffer address is set to ADDR. 636 * If len != 0 then data is copied from the interface buffer to the 637 * address starting at buf. 638 * BUF must be usable as a uint16_t *. 639 * If LEN is odd, it must be safe to overwrite one extra byte. 640 */ 641 642 static void 643 ea_readbuf(struct seeq8005_softc *sc, u_char *buf, int addr, size_t len) 644 { 645 bus_space_tag_t iot = sc->sc_iot; 646 bus_space_handle_t ioh = sc->sc_ioh; 647 int runup; 648 649 DPRINTF(SEEQ_DEBUG_MISC, ("readbuf: st=%04x addr=%04x len=%d\n", 650 SEEQ_READ16(sc, iot, ioh, SEEQ_STATUS), addr, len)); 651 652 #ifdef DIAGNOSTIC 653 if (__predict_false(!ALIGNED_POINTER(buf, uint16_t))) 654 panic("%s: unaligned readbuf", device_xname(sc->sc_dev)); 655 if (__predict_false(addr >= SEEQ_MAX_BUFFER_SIZE)) 656 panic("%s: readbuf out of range", device_xname(sc->sc_dev)); 657 #endif 658 659 if (addr != -1) { 660 /* 661 * SEEQ 80C04 bug: 662 * Starting reading from certain addresses seems to cause 663 * us to get bogus results, so we avoid them. 664 */ 665 runup = 0; 666 if (sc->sc_variant == SEEQ_8004 && 667 ((addr & 0x00ff) == 0x00ea || 668 (addr & 0x00ff) == 0x00ee || 669 (addr & 0x00ff) == 0x00f0)) 670 runup = (addr & 0x00ff) - 0x00e8; 671 672 ea_await_fifo_empty(sc); 673 674 ea_select_buffer(sc, SEEQ_BUFCODE_LOCAL_MEM); 675 676 /* 677 * 80C04 bug workaround. I found this in the old arm32 "eb" 678 * driver. I've no idea what it does, but it seems to stop 679 * the chip mangling data so often. 680 */ 681 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, 682 sc->sc_command | SEEQ_CMD_FIFO_WRITE); 683 ea_await_fifo_empty(sc); 684 685 SEEQ_WRITE16(sc, iot, ioh, SEEQ_DMA_ADDR, addr - runup); 686 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, 687 sc->sc_command | SEEQ_CMD_FIFO_READ); 688 689 ea_await_fifo_full(sc); 690 while (runup > 0) { 691 /* LINTED: Reading a volatile _does_ have an effect */ 692 (void)SEEQ_READ16(sc, iot, ioh, SEEQ_BUFWIN); 693 runup -= 2; 694 } 695 } 696 697 if (len > 0) { 698 if (sc->sc_flags & SF_8BIT) 699 bus_space_read_multi_1(iot, ioh, SEEQ_BUFWIN, 700 (uint8_t *)buf, len); 701 else 702 bus_space_read_multi_2(iot, ioh, SEEQ_BUFWIN, 703 /* LINTED: pointer alignment checked above */ 704 (uint16_t *)buf, len / 2); 705 } 706 if (!(sc->sc_flags & SF_8BIT) && len % 2) { 707 /* Read the last byte */ 708 buf[len - 1] = bus_space_read_2(iot, ioh, SEEQ_BUFWIN); 709 } 710 } 711 712 static void 713 ea_select_buffer(struct seeq8005_softc *sc, int bufcode) 714 { 715 716 SEEQ_WRITE16(sc, sc->sc_iot, sc->sc_ioh, SEEQ_CONFIG1, 717 sc->sc_config1 | bufcode); 718 } 719 720 /* Must be called at splnet */ 721 static void 722 ea_set_address(struct seeq8005_softc *sc, int which, const uint8_t *ea) 723 { 724 int i; 725 726 ea_select_buffer(sc, SEEQ_BUFCODE_STATION_ADDR0 + which); 727 for (i = 0; i < ETHER_ADDR_LEN; ++i) 728 SEEQ_WRITE16(sc, sc->sc_iot, sc->sc_ioh, SEEQ_BUFWIN, ea[i]); 729 } 730 731 /* 732 * Initialize interface. 733 * 734 * This should leave the interface in a state for packet reception and 735 * transmission. 736 */ 737 738 static int 739 ea_init(struct ifnet *ifp) 740 { 741 struct seeq8005_softc *sc = ifp->if_softc; 742 bus_space_tag_t iot = sc->sc_iot; 743 bus_space_handle_t ioh = sc->sc_ioh; 744 int s; 745 746 DPRINTF(SEEQ_DEBUG_MISC, ("ea_init()\n")); 747 748 s = splnet(); 749 750 /* First, reset the board. */ 751 752 ea_chipreset(sc); 753 754 /* Set up defaults for the registers */ 755 756 sc->sc_command = 0; 757 sc->sc_config1 = 0; 758 #if BYTE_ORDER == BIG_ENDIAN 759 sc->sc_config2 = SEEQ_CFG2_BYTESWAP; 760 #else 761 sc->sc_config2 = 0; 762 #endif 763 sc->sc_config3 = 0; 764 765 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, sc->sc_command); 766 SEEQ_WRITE16(sc, iot, ioh, SEEQ_CONFIG1, sc->sc_config1); 767 SEEQ_WRITE16(sc, iot, ioh, SEEQ_CONFIG2, sc->sc_config2); 768 if (sc->sc_variant == SEEQ_8004) { 769 ea_select_buffer(sc, SEEQ_BUFCODE_CONFIG3); 770 SEEQ_WRITE16(sc, iot, ioh, SEEQ_BUFWIN, sc->sc_config3); 771 } 772 773 /* Write the station address - the receiver must be off */ 774 ea_set_address(sc, 0, (const uint8_t *)CLLADDR(ifp->if_sadl)); 775 776 /* Split board memory into Rx and Tx. */ 777 ea_select_buffer(sc, SEEQ_BUFCODE_TX_EAP); 778 SEEQ_WRITE16(sc, iot, ioh, SEEQ_BUFWIN, (sc->sc_tx_bufsize>> 8) - 1); 779 780 if (sc->sc_variant == SEEQ_8004) { 781 /* Make the interface IFF_SIMPLEX. */ 782 sc->sc_config2 |= SEEQ_CFG2_RX_TX_DISABLE; 783 /* Enable reception of long packets (for vlan(4)). */ 784 sc->sc_config2 |= SEEQ_CFG2_PASS_LONGSHORT; 785 } 786 787 /* Configure rx. */ 788 ea_mc_reset(sc); 789 if (ifp->if_flags & IFF_PROMISC) 790 sc->sc_config1 = SEEQ_CFG1_PROMISCUOUS; 791 else if ((ifp->if_flags & IFF_ALLMULTI) || sc->sc_variant == SEEQ_8004) 792 sc->sc_config1 = SEEQ_CFG1_MULTICAST; 793 else 794 sc->sc_config1 = SEEQ_CFG1_BROADCAST; 795 sc->sc_config1 |= SEEQ_CFG1_STATION_ADDR0; 796 SEEQ_WRITE16(sc, iot, ioh, SEEQ_CONFIG1, sc->sc_config1); 797 798 /* Setup the Rx pointers */ 799 sc->sc_rx_ptr = sc->sc_tx_bufsize; 800 801 SEEQ_WRITE16(sc, iot, ioh, SEEQ_RX_PTR, sc->sc_rx_ptr); 802 SEEQ_WRITE16(sc, iot, ioh, SEEQ_RX_END, sc->sc_rx_ptr >> 8); 803 804 805 /* Place a NULL header at the beginning of the receive area */ 806 ea_writebuf(sc, NULL, sc->sc_rx_ptr, 0); 807 808 SEEQ_WRITE16(sc, iot, ioh, SEEQ_BUFWIN, 0x0000); 809 SEEQ_WRITE16(sc, iot, ioh, SEEQ_BUFWIN, 0x0000); 810 811 812 /* Configure TX. */ 813 DPRINTF(SEEQ_DEBUG_MISC, ("Configuring tx...\n")); 814 815 SEEQ_WRITE16(sc, iot, ioh, SEEQ_TX_PTR, 0x0000); 816 817 sc->sc_config2 |= SEEQ_CFG2_OUTPUT; 818 SEEQ_WRITE16(sc, iot, ioh, SEEQ_CONFIG2, sc->sc_config2); 819 820 /* Reset tx buffer pointers */ 821 sc->sc_tx_cur = 0; 822 sc->sc_tx_used = 0; 823 sc->sc_tx_next = 0; 824 825 /* Place a NULL header at the beginning of the transmit area */ 826 ea_writebuf(sc, NULL, 0x0000, 0); 827 828 SEEQ_WRITE16(sc, iot, ioh, SEEQ_BUFWIN, 0x0000); 829 SEEQ_WRITE16(sc, iot, ioh, SEEQ_BUFWIN, 0x0000); 830 831 sc->sc_command |= SEEQ_CMD_TX_INTEN; 832 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, sc->sc_command); 833 834 /* Turn on Rx */ 835 sc->sc_command |= SEEQ_CMD_RX_INTEN; 836 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, 837 sc->sc_command | SEEQ_CMD_RX_ON); 838 839 /* TX_ON gets set by ea_txpacket when there's something to transmit. */ 840 841 842 /* Set flags appropriately. */ 843 ifp->if_flags |= IFF_RUNNING; 844 ifp->if_flags &= ~IFF_OACTIVE; 845 sc->sc_enabled = 1; 846 847 /* And start output. */ 848 ea_start(ifp); 849 850 splx(s); 851 return 0; 852 } 853 854 /* 855 * Start output on interface. Get datagrams from the queue and output them, 856 * giving the receiver a chance between datagrams. Call only from splnet or 857 * interrupt level! 858 */ 859 860 static void 861 ea_start(struct ifnet *ifp) 862 { 863 struct seeq8005_softc *sc = ifp->if_softc; 864 int s; 865 866 s = splnet(); 867 DPRINTF(SEEQ_DEBUG_TX, ("ea_start()...\n")); 868 869 /* 870 * Don't do anything if output is active. seeq8005intr() will call 871 * us (actually ea_txpacket()) back when the card's ready for more 872 * frames. 873 */ 874 if (ifp->if_flags & IFF_OACTIVE) { 875 splx(s); 876 return; 877 } 878 879 /* Mark interface as output active */ 880 881 ifp->if_flags |= IFF_OACTIVE; 882 883 /* tx packets */ 884 885 ea_txpacket(sc); 886 splx(s); 887 } 888 889 890 /* 891 * Transfer a packet to the interface buffer and start transmission 892 * 893 * Called at splnet() 894 */ 895 896 static void 897 ea_txpacket(struct seeq8005_softc *sc) 898 { 899 bus_space_tag_t iot = sc->sc_iot; 900 bus_space_handle_t ioh = sc->sc_ioh; 901 struct mbuf *m0; 902 struct ifnet *ifp; 903 904 ifp = &sc->sc_ethercom.ec_if; 905 906 /* Dequeue the next packet. */ 907 IFQ_DEQUEUE(&ifp->if_snd, m0); 908 909 /* If there's nothing to send, return. */ 910 if (m0 == NULL) { 911 ifp->if_flags &= ~IFF_OACTIVE; 912 sc->sc_config2 |= SEEQ_CFG2_OUTPUT; 913 SEEQ_WRITE16(sc, iot, ioh, SEEQ_CONFIG2, sc->sc_config2); 914 DPRINTF(SEEQ_DEBUG_TX, ("tx finished\n")); 915 return; 916 } 917 918 /* Give the packet to the bpf, if any. */ 919 bpf_mtap(ifp, m0, BPF_D_OUT); 920 921 DPRINTF(SEEQ_DEBUG_TX, ("Tx new packet\n")); 922 923 sc->sc_config2 &= ~SEEQ_CFG2_OUTPUT; 924 SEEQ_WRITE16(sc, iot, ioh, SEEQ_CONFIG2, sc->sc_config2); 925 926 ea_writembuf(sc, m0, 0x0000); 927 m_freem(m0); 928 929 SEEQ_WRITE16(sc, iot, ioh, SEEQ_TX_PTR, 0x0000); 930 931 /* Now transmit the datagram. */ 932 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, 933 sc->sc_command | SEEQ_CMD_TX_ON); 934 935 /* Make sure we notice if the chip goes silent on us. */ 936 ifp->if_timer = 5; 937 938 DPRINTF(SEEQ_DEBUG_TX, 939 ("st=%04x\n", SEEQ_READ16(sc, iot, ioh, SEEQ_STATUS))); 940 DPRINTF(SEEQ_DEBUG_TX, ("tx: queued\n")); 941 } 942 943 /* 944 * Copy a packet from an mbuf to the transmit buffer on the card. 945 * 946 * Puts a valid Tx header at the start of the packet, and a null header at 947 * the end. 948 */ 949 static int 950 ea_writembuf(struct seeq8005_softc *sc, struct mbuf *m0, int bufstart) 951 { 952 struct mbuf *m; 953 int len, nextpacket; 954 uint8_t hdr[4]; 955 956 /* 957 * Copy the datagram to the packet buffer. 958 */ 959 len = 0; 960 for (m = m0; m; m = m->m_next) { 961 if (m->m_len == 0) 962 continue; 963 ea_writebuf(sc, mtod(m, u_char *), bufstart + 4 + len, 964 m->m_len); 965 len += m->m_len; 966 } 967 968 if (len < ETHER_MIN_LEN) { 969 ea_writebuf(sc, padbuf, bufstart + 4 + len, 970 ETHER_MIN_LEN - len); 971 len = ETHER_MIN_LEN; 972 } 973 974 /* Follow it with a NULL packet header */ 975 memset(hdr, 0, 4); 976 ea_writebuf(sc, hdr, bufstart + 4 + len, 4); 977 978 /* Ok we now have a packet len bytes long in our packet buffer */ 979 DPRINTF(SEEQ_DEBUG_TX, ("ea_writembuf: length=%d\n", len)); 980 981 /* Write the packet header */ 982 nextpacket = bufstart + len + 4; 983 hdr[0] = (nextpacket >> 8) & 0xff; 984 hdr[1] = nextpacket & 0xff; 985 hdr[2] = SEEQ_PKTCMD_TX | SEEQ_PKTCMD_DATA_FOLLOWS | 986 SEEQ_TXCMD_XMIT_SUCCESS_INT | SEEQ_TXCMD_COLLISION_INT; 987 hdr[3] = 0; /* Status byte -- will be updated by hardware. */ 988 ea_writebuf(sc, hdr, bufstart, 4); 989 990 return len; 991 } 992 993 /* 994 * Ethernet controller interrupt. 995 */ 996 997 int 998 seeq8005intr(void *arg) 999 { 1000 struct seeq8005_softc *sc = arg; 1001 bus_space_tag_t iot = sc->sc_iot; 1002 bus_space_handle_t ioh = sc->sc_ioh; 1003 int status, handled; 1004 1005 handled = 0; 1006 1007 /* Get the controller status */ 1008 status = SEEQ_READ16(sc, iot, ioh, SEEQ_STATUS); 1009 1010 /* Tx interrupt ? */ 1011 if (status & SEEQ_STATUS_TX_INT) { 1012 handled = 1; 1013 1014 /* Acknowledge the interrupt */ 1015 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, 1016 sc->sc_command | SEEQ_CMD_TX_INTACK); 1017 1018 ea_txint(sc); 1019 } 1020 1021 1022 /* Rx interrupt ? */ 1023 if (status & SEEQ_STATUS_RX_INT) { 1024 handled = 1; 1025 1026 /* Acknowledge the interrupt */ 1027 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, 1028 sc->sc_command | SEEQ_CMD_RX_INTACK); 1029 1030 /* Processes the received packets */ 1031 ea_rxint(sc); 1032 } 1033 1034 if (handled) 1035 rnd_add_uint32(&sc->rnd_source, status); 1036 1037 return handled; 1038 } 1039 1040 static void 1041 ea_txint(struct seeq8005_softc *sc) 1042 { 1043 struct ifnet *ifp = &sc->sc_ethercom.ec_if; 1044 bus_space_tag_t iot = sc->sc_iot; 1045 bus_space_handle_t ioh = sc->sc_ioh; 1046 uint8_t txhdr[4]; 1047 u_int txstatus; 1048 1049 ea_readbuf(sc, txhdr, 0x0000, 4); 1050 1051 DPRINTF(SEEQ_DEBUG_TX, ("txstatus=%02x %02x %02x %02x\n", 1052 txhdr[0], txhdr[1], txhdr[2], txhdr[3])); 1053 txstatus = txhdr[3]; 1054 1055 /* 1056 * If SEEQ_TXSTAT_COLLISION is set then we received at least 1057 * one collision. On the 8004 we can find out exactly how many 1058 * collisions occurred. 1059 * 1060 * The SEEQ_PKTSTAT_DONE will be set if the transmission has 1061 * completed. 1062 * 1063 * If SEEQ_TXSTAT_COLLISION16 is set then 16 collisions 1064 * occurred and the packet transmission was aborted. 1065 * This situation is untested as present. 1066 * 1067 * The SEEQ_TXSTAT_BABBLE is untested as it should only be set 1068 * when we deliberately transmit oversized packets (e.g. for 1069 * 802.1Q). 1070 */ 1071 if (txstatus & SEEQ_TXSTAT_COLLISION) { 1072 switch (sc->sc_variant) { 1073 case SEEQ_8004: { 1074 int colls; 1075 1076 /* 1077 * The 8004 contains a 4 bit collision count 1078 * in the status register. 1079 */ 1080 #if 0 1081 /* This appears to be broken on 80C04.AE */ 1082 if_statadd(ifp, if_collisions, 1083 (txstatus >> SEEQ_TXSTAT_COLLISIONS_SHIFT) 1084 & SEEQ_TXSTAT_COLLISION_MASK; 1085 #endif 1086 1087 /* Use the TX Collision register */ 1088 ea_select_buffer(sc, SEEQ_BUFCODE_TX_COLLS); 1089 colls = bus_space_read_1(iot, ioh, SEEQ_BUFWIN); 1090 if_statadd(ifp, if_collisions, colls); 1091 break; 1092 } 1093 case SEEQ_8005: 1094 /* We known there was at least 1 collision */ 1095 if_statinc(ifp, if_collisions); 1096 break; 1097 } 1098 } else if (txstatus & SEEQ_TXSTAT_COLLISION16) { 1099 printf("seeq_intr: col16 %x\n", txstatus); 1100 if_statadd2(ifp, if_collisions, 16, if_oerrors, 1); 1101 } 1102 1103 /* Have we completed transmission on the packet ? */ 1104 if (txstatus & SEEQ_PKTSTAT_DONE) { 1105 /* Clear watchdog timer. */ 1106 ifp->if_timer = 0; 1107 ifp->if_flags &= ~IFF_OACTIVE; 1108 1109 /* Update stats */ 1110 if_statinc(ifp, if_opackets); 1111 1112 /* Tx next packet */ 1113 1114 ea_txpacket(sc); 1115 } 1116 } 1117 1118 static void 1119 ea_rxint(struct seeq8005_softc *sc) 1120 { 1121 bus_space_tag_t iot = sc->sc_iot; 1122 bus_space_handle_t ioh = sc->sc_ioh; 1123 u_int addr; 1124 int len; 1125 int ctrl; 1126 int ptr; 1127 int status; 1128 uint8_t rxhdr[4]; 1129 struct ifnet *ifp; 1130 1131 ifp = &sc->sc_ethercom.ec_if; 1132 1133 1134 /* We start from the last rx pointer position */ 1135 addr = sc->sc_rx_ptr; 1136 sc->sc_config2 &= ~SEEQ_CFG2_OUTPUT; 1137 SEEQ_WRITE16(sc, iot, ioh, SEEQ_CONFIG2, sc->sc_config2); 1138 1139 do { 1140 /* Read rx header */ 1141 ea_readbuf(sc, rxhdr, addr, 4); 1142 1143 /* Split the packet header */ 1144 ptr = (rxhdr[0] << 8) | rxhdr[1]; 1145 ctrl = rxhdr[2]; 1146 status = rxhdr[3]; 1147 1148 DPRINTF(SEEQ_DEBUG_RX, 1149 ("addr=%04x ptr=%04x ctrl=%02x status=%02x\n", 1150 addr, ptr, ctrl, status)); 1151 1152 /* Zero packet ptr ? then must be null header so exit */ 1153 if (ptr == 0) break; 1154 1155 /* Sanity-check the next-packet pointer and flags. */ 1156 if (__predict_false(ptr < sc->sc_tx_bufsize || 1157 (ctrl & SEEQ_PKTCMD_TX))) { 1158 if_statinc(ifp, if_ierrors); 1159 log(LOG_ERR, 1160 "%s: Rx chain corrupt at %04x (ptr = %04x)\n", 1161 device_xname(sc->sc_dev), addr, ptr); 1162 ea_init(ifp); 1163 return; 1164 } 1165 1166 /* Get packet length */ 1167 len = (ptr - addr) - 4; 1168 1169 if (len < 0) 1170 len += sc->sc_rx_bufsize; 1171 DPRINTF(SEEQ_DEBUG_RX, ("len=%04x\n", len)); 1172 1173 /* Has the packet rx completed ? if not then exit */ 1174 if ((status & SEEQ_PKTSTAT_DONE) == 0) 1175 break; 1176 1177 /* 1178 * Did we have any errors? then note error and go to 1179 * next packet 1180 */ 1181 if (__predict_false(status & 1182 (SEEQ_RXSTAT_CRC_ERROR | SEEQ_RXSTAT_DRIBBLE_ERROR | 1183 SEEQ_RXSTAT_SHORT_FRAME))) { 1184 if_statinc(ifp, if_ierrors); 1185 log(LOG_WARNING, 1186 "%s: rx packet error at %04x (err=%02x)\n", 1187 device_xname(sc->sc_dev), addr, status & 0x0f); 1188 /* XXX shouldn't need to reset if it's genuine. */ 1189 ea_init(ifp); 1190 return; 1191 } 1192 /* 1193 * Is the packet too big? We allow slightly oversize packets 1194 * for vlan(4) and tcpdump purposes, but the rest of the world 1195 * wants incoming packets in a single mbuf cluster. 1196 */ 1197 if (__predict_false(len > MCLBYTES)) { 1198 if_statinc(ifp, if_ierrors); 1199 log(LOG_ERR, 1200 "%s: rx packet size error at %04x (len=%d)\n", 1201 device_xname(sc->sc_dev), addr, len); 1202 ea_init(ifp); 1203 return; 1204 } 1205 1206 /* Pass data up to upper levels. */ 1207 ea_read(sc, addr + 4, len); 1208 1209 addr = ptr; 1210 } while (len != 0); 1211 1212 sc->sc_config2 |= SEEQ_CFG2_OUTPUT; 1213 SEEQ_WRITE16(sc, iot, ioh, SEEQ_CONFIG2, sc->sc_config2); 1214 1215 DPRINTF(SEEQ_DEBUG_RX, ("new rx ptr=%04x\n", addr)); 1216 1217 /* Store new rx pointer */ 1218 sc->sc_rx_ptr = addr; 1219 SEEQ_WRITE16(sc, iot, ioh, SEEQ_RX_END, sc->sc_rx_ptr >> 8); 1220 1221 /* Make sure the receiver is on */ 1222 SEEQ_WRITE16(sc, iot, ioh, SEEQ_COMMAND, 1223 sc->sc_command | SEEQ_CMD_RX_ON); 1224 } 1225 1226 1227 /* 1228 * Pass a packet up to the higher levels. 1229 */ 1230 1231 static void 1232 ea_read(struct seeq8005_softc *sc, int addr, int len) 1233 { 1234 struct mbuf *m; 1235 struct ifnet *ifp; 1236 1237 ifp = &sc->sc_ethercom.ec_if; 1238 1239 /* Pull packet off interface. */ 1240 m = ea_get(sc, addr, len, ifp); 1241 if (m == NULL) 1242 return; 1243 1244 if_percpuq_enqueue(ifp->if_percpuq, m); 1245 } 1246 1247 /* 1248 * Pull read data off a interface. Len is length of data, with local net 1249 * header stripped. We copy the data into mbufs. When full cluster sized 1250 * units are present we copy into clusters. 1251 */ 1252 1253 struct mbuf * 1254 ea_get(struct seeq8005_softc *sc, int addr, int totlen, struct ifnet *ifp) 1255 { 1256 struct mbuf *top, **mp, *m; 1257 int len; 1258 u_int cp, epkt; 1259 1260 cp = addr; 1261 epkt = cp + totlen; 1262 1263 MGETHDR(m, M_DONTWAIT, MT_DATA); 1264 if (m == NULL) 1265 return NULL; 1266 m_set_rcvif(m, ifp); 1267 m->m_pkthdr.len = totlen; 1268 m->m_len = MHLEN; 1269 top = NULL; 1270 mp = ⊤ 1271 1272 while (totlen > 0) { 1273 if (top) { 1274 MGET(m, M_DONTWAIT, MT_DATA); 1275 if (m == NULL) { 1276 m_freem(top); 1277 return NULL; 1278 } 1279 m->m_len = MLEN; 1280 } 1281 len = uimin(totlen, epkt - cp); 1282 if (len >= MINCLSIZE) { 1283 MCLGET(m, M_DONTWAIT); 1284 if (m->m_flags & M_EXT) 1285 m->m_len = len = uimin(len, MCLBYTES); 1286 else 1287 len = m->m_len; 1288 } else { 1289 /* 1290 * Place initial small packet/header at end of mbuf. 1291 */ 1292 if (len < m->m_len) { 1293 if (top == NULL && len + max_linkhdr <= m->m_len) 1294 m->m_data += max_linkhdr; 1295 m->m_len = len; 1296 } else 1297 len = m->m_len; 1298 } 1299 if (top == NULL) { 1300 /* Make sure the payload is aligned */ 1301 char *newdata = (char *) 1302 ALIGN((char*)m->m_data + 1303 sizeof(struct ether_header)) - 1304 sizeof(struct ether_header); 1305 len -= newdata - m->m_data; 1306 m->m_len = len; 1307 m->m_data = newdata; 1308 } 1309 ea_readbuf(sc, mtod(m, u_char *), 1310 cp < SEEQ_MAX_BUFFER_SIZE ? cp : cp - sc->sc_rx_bufsize, 1311 len); 1312 cp += len; 1313 *mp = m; 1314 mp = &m->m_next; 1315 totlen -= len; 1316 if (cp == epkt) 1317 cp = addr; 1318 } 1319 1320 return top; 1321 } 1322 1323 /* 1324 * Process an ioctl request. Mostly boilerplate. 1325 */ 1326 static int 1327 ea_ioctl(struct ifnet *ifp, u_long cmd, void *data) 1328 { 1329 struct seeq8005_softc *sc = ifp->if_softc; 1330 int s, error = 0; 1331 1332 s = splnet(); 1333 switch (cmd) { 1334 1335 default: 1336 error = ether_ioctl(ifp, cmd, data); 1337 if (error == ENETRESET) { 1338 /* 1339 * Multicast list has changed; set the hardware filter 1340 * accordingly. 1341 */ 1342 if (ifp->if_flags & IFF_RUNNING) 1343 ea_mc_reset(sc); 1344 error = 0; 1345 } 1346 break; 1347 } 1348 1349 splx(s); 1350 return error; 1351 } 1352 1353 /* Must be called at splnet() */ 1354 1355 static void 1356 ea_mc_reset(struct seeq8005_softc *sc) 1357 { 1358 1359 switch (sc->sc_variant) { 1360 case SEEQ_8004: 1361 ea_mc_reset_8004(sc); 1362 return; 1363 case SEEQ_8005: 1364 ea_mc_reset_8005(sc); 1365 return; 1366 } 1367 } 1368 1369 static void 1370 ea_mc_reset_8004(struct seeq8005_softc *sc) 1371 { 1372 struct ethercom *ec = &sc->sc_ethercom; 1373 struct ifnet *ifp = &ec->ec_if; 1374 struct ether_multi *enm; 1375 uint32_t crc; 1376 int i; 1377 struct ether_multistep step; 1378 uint8_t af[8]; 1379 1380 /* 1381 * Set up multicast address filter by passing all multicast addresses 1382 * through a crc generator, and then using bits 2 - 7 as an index 1383 * into the 64 bit logical address filter. The high order bits 1384 * selects the word, while the rest of the bits select the bit within 1385 * the word. 1386 */ 1387 1388 if (ifp->if_flags & IFF_PROMISC) { 1389 ifp->if_flags |= IFF_ALLMULTI; 1390 for (i = 0; i < 8; i++) 1391 af[i] = 0xff; 1392 return; 1393 } 1394 for (i = 0; i < 8; i++) 1395 af[i] = 0; 1396 1397 ETHER_LOCK(ec); 1398 ETHER_FIRST_MULTI(step, ec, enm); 1399 while (enm != NULL) { 1400 if (memcmp(enm->enm_addrlo, enm->enm_addrhi, 1401 sizeof(enm->enm_addrlo)) != 0) { 1402 /* 1403 * We must listen to a range of multicast addresses. 1404 * For now, just accept all multicasts, rather than 1405 * trying to set only those filter bits needed to match 1406 * the range. (At this time, the only use of address 1407 * ranges is for IP multicast routing, for which the 1408 * range is big enough to require all bits set.) 1409 */ 1410 ifp->if_flags |= IFF_ALLMULTI; 1411 for (i = 0; i < 8; i++) 1412 af[i] = 0xff; 1413 break; 1414 } 1415 1416 crc = ether_crc32_be(enm->enm_addrlo, sizeof(enm->enm_addrlo)); 1417 1418 /* Just want the 6 most significant bits. */ 1419 crc = (crc >> 2) & 0x3f; 1420 1421 /* Turn on the corresponding bit in the filter. */ 1422 af[crc >> 3] |= 1 << (crc & 0x7); 1423 1424 ETHER_NEXT_MULTI(step, enm); 1425 } 1426 ETHER_UNLOCK(ec); 1427 ifp->if_flags &= ~IFF_ALLMULTI; 1428 1429 ea_select_buffer(sc, SEEQ_BUFCODE_MULTICAST); 1430 for (i = 0; i < 8; ++i) 1431 bus_space_write_1(sc->sc_iot, sc->sc_ioh, 1432 SEEQ_BUFWIN, af[i]); 1433 } 1434 1435 static void 1436 ea_mc_reset_8005(struct seeq8005_softc *sc) 1437 { 1438 struct ethercom *ec = &sc->sc_ethercom; 1439 struct ether_multi *enm; 1440 struct ether_multistep step; 1441 int naddr, maxaddrs; 1442 1443 naddr = 0; 1444 maxaddrs = 5; 1445 ETHER_LOCK(ec); 1446 ETHER_FIRST_MULTI(step, ec, enm); 1447 while (enm != NULL) { 1448 /* Have we got space? */ 1449 if (naddr >= maxaddrs || 1450 memcmp(enm->enm_addrlo, enm->enm_addrhi, 6) != 0) { 1451 ec->ec_if.if_flags |= IFF_ALLMULTI; 1452 ETHER_UNLOCK(ec); 1453 ea_ioctl(&ec->ec_if, SIOCSIFFLAGS, NULL); 1454 return; 1455 } 1456 ea_set_address(sc, 1 + naddr, enm->enm_addrlo); 1457 sc->sc_config1 |= SEEQ_CFG1_STATION_ADDR1 << naddr; 1458 naddr++; 1459 ETHER_NEXT_MULTI(step, enm); 1460 } 1461 ETHER_UNLOCK(ec); 1462 1463 for (; naddr < maxaddrs; naddr++) 1464 sc->sc_config1 &= ~(SEEQ_CFG1_STATION_ADDR1 << naddr); 1465 SEEQ_WRITE16(sc, sc->sc_iot, sc->sc_ioh, SEEQ_CONFIG1, 1466 sc->sc_config1); 1467 } 1468 1469 /* 1470 * Device timeout routine. 1471 */ 1472 1473 static void 1474 ea_watchdog(struct ifnet *ifp) 1475 { 1476 struct seeq8005_softc *sc = ifp->if_softc; 1477 1478 log(LOG_ERR, "%s: lost Tx interrupt (status = 0x%04x)\n", 1479 device_xname(sc->sc_dev), 1480 SEEQ_READ16(sc, sc->sc_iot, sc->sc_ioh, SEEQ_STATUS)); 1481 if_statinc(ifp, if_oerrors); 1482 1483 /* Kick the interface */ 1484 1485 ea_init(ifp); 1486 1487 ifp->if_timer = 0; 1488 } 1489 1490 /* End of seeq8005.c */ 1491
Indexes created Mon Sep 29 21:09:56 GMT 2025