HomeSort by: relevance | last modified time | path
    Searched refs:routed (Results 1 - 25 of 43) sorted by relevancy

1 2

  /src/sbin/routed/
Makefile 5 PROG= routed
7 MAN= routed.8
14 MLINKS= routed.8 rdisc.8
  /src/etc/rc.d/
routed 3 # $NetBSD: routed,v 1.10 2007/04/21 15:20:07 tron Exp $
6 # PROVIDE: routed
12 name="routed"
19 if checkyesno gated && checkyesno routed; then
20 warn "gated and routed both requested to be run: only running gated."
Makefile 38 rbootd resize_root rndctl root route6d routed rtadvd \
  /src/sys/dist/pf/net/
pf_mtag.h 52 u_int8_t routed; member in struct:pf_mtag
  /src/sys/external/gpl2/dts/dist/arch/arm/boot/dts/
armada-385-turris-omnia.dts 316 /* routed to PCIe0/mSATA connector (CN7A) */
324 /* routed to PCIe1/USB2 connector (CN61A) */
332 /* routed to PCIe2 connector (CN62A) */
340 /* routed to SFP+ */
509 /* MISO, MOSI, SCLK and CS1 are routed to pin header CN11 */
imx6qdl-dhcom-drc02.dtsi 15 * Tx and Rx are routed to the DHCOM UART1 rts/cts pins. Therefore the micro SD
72 * Due to the use of can2 the signals for can2 Tx and Rx are routed to
berlin2cd-valve-steamlink.dts 66 /* RX/TX are routed to TP50/TP51 on the board. */
kirkwood-blackarmor-nas220.dts 95 * Serial port routed to connector CN5
logicpd-torpedo-37xx-devkit.dts 28 * MMC3 can be routed with jumpers to the second MMC slot on the devkit and
am335x-bonegreen-wireless.dts 115 /* On the BBGW this pin is routed through the level shifter (U21) that */
ste-nomadik-nhk15.dts 75 /* This is where the interrupt is routed on the NHK-15 debug board */
r8a7790-lager.dts 301 * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
320 * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
r8a7791-koelsch.dts 345 * I2C1 is routed to EXIO connector B, pins 64 (SCL) + 66 (SDA).
451 * I2C4 is routed to EXIO connector E, pins 37 (SCL) + 39 (SDA).
  /src/sys/external/gpl2/dts/dist/arch/arm64/boot/dts/bitmain/
bm1880-sophon-edge.dts 13 * NC = not connected (pin out but not routed from the chip to
22 * For the lines routed to the external connectors the
  /src/sbin/
Makefile 15 ping pppoectl raidctl reboot rcorder rndctl route routed \
  /src/sys/external/gpl2/dts/dist/arch/riscv/boot/dts/allwinner/
sun20i-d1-nezha.dts 7 * The Nezha-D1 has a 40-pin IO header. Some of these pins are routed
12 * Lines which are routed to the 40-pin header are named as follows:
  /src/include/
Makefile 29 INCS+= protocols/dumprestore.h protocols/routed.h protocols/rwhod.h \
  /src/sys/external/gpl2/dts/dist/arch/arm64/boot/dts/hisilicon/
hi6220-hikey.dts 349 * NC = not connected (not routed from the SoC)
359 * For the lines routed to the external connectors the
488 /* GPIO blocks 16 thru 19 do not appear to be routed to pins */
hi3670-hikey970.dts 76 * NC = not connected (pin out but not routed from the chip to
86 * For the lines routed to the external connectors the
hi3660-hikey960.dts 204 * NC = not connected (pin out but not routed from the chip to
216 * For the lines routed to the external connectors the
  /src/sys/external/gpl2/dts/dist/arch/arm64/boot/dts/nvidia/
tegra234.dtsi 84 * Shared interrupt 0 is routed only to AON/SPE, so
  /src/sys/external/gpl2/dts/dist/arch/arm64/boot/dts/actions/
s900-bubblegum-96.dts 69 * NC = not connected (pin out but not routed from the chip to
78 * For the lines routed to the external connectors the
  /src/etc/defaults/
rc.conf 269 routed=NO routed_flags="-q" key
  /src/sys/external/gpl2/dts/dist/arch/arm64/boot/dts/xilinx/
zynqmp-zcu100-revC.dts 217 /* MIO31 is alert which should be routed to PMUFW */
  /src/sys/external/gpl2/dts/dist/arch/arm64/boot/dts/qcom/
apq8016-sbc.dtsi 549 * NC = not connected (pin out but not routed from the chip to
558 * For the lines routed to the external connectors the

Completed in 90 milliseconds

1 2