1 /* $NetBSD: osiopreg.h,v 1.6 2012/08/24 09:01:23 msaitoh Exp $ */ 2 3 /* 4 * Copyright (c) 1990 The Regents of the University of California. 5 * All rights reserved. 6 * 7 * This code is derived from software contributed to Berkeley by 8 * Van Jacobson of Lawrence Berkeley Laboratory. 9 * 10 * Redistribution and use in source and binary forms, with or without 11 * modification, are permitted provided that the following conditions 12 * are met: 13 * 1. Redistributions of source code must retain the above copyright 14 * notice, this list of conditions and the following disclaimer. 15 * 2. Redistributions in binary form must reproduce the above copyright 16 * notice, this list of conditions and the following disclaimer in the 17 * documentation and/or other materials provided with the distribution. 18 * 3. Neither the name of the University nor the names of its contributors 19 * may be used to endorse or promote products derived from this software 20 * without specific prior written permission. 21 * 22 * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND 23 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 24 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 25 * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE 26 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 27 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 28 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 29 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 30 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 31 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 32 * SUCH DAMAGE. 33 * 34 * @(#)siopreg.h 7.3 (Berkeley) 2/5/91 35 */ 36 37 /* 38 * NCR 53C710 SCSI interface hardware description. 39 * 40 * From the Mach scsi driver for the 53C710 and amiga siop driver 41 */ 42 43 /* byte lane definitions */ 44 #if BYTE_ORDER == LITTLE_ENDIAN 45 #define BL0 0 46 #define BL1 1 47 #define BL2 2 48 #define BL3 3 49 #else 50 #define BL0 3 51 #define BL1 2 52 #define BL2 1 53 #define BL3 0 54 #endif 55 56 #define OSIOP_SCNTL0 (0x00+BL0) /* rw: SCSI control reg 0 */ 57 #define OSIOP_SCNTL1 (0x00+BL1) /* rw: SCSI control reg 1 */ 58 #define OSIOP_SDID (0x00+BL2) /* rw: SCSI destination ID */ 59 #define OSIOP_SIEN (0x00+BL3) /* rw: SCSI interrupt enable */ 60 61 #define OSIOP_SCID (0x04+BL0) /* rw: SCSI Chip ID reg */ 62 #define OSIOP_SXFER (0x04+BL1) /* rw: SCSI Transfer reg */ 63 #define OSIOP_SODL (0x04+BL2) /* rw: SCSI Output Data Latch */ 64 #define OSIOP_SOCL (0x04+BL3) /* rw: SCSI Output Control Latch */ 65 66 #define OSIOP_SFBR (0x08+BL0) /* ro: SCSI First Byte Received */ 67 #define OSIOP_SIDL (0x08+BL1) /* ro: SCSI Input Data Latch */ 68 #define OSIOP_SBDL (0x08+BL2) /* ro: SCSI Bus Data Lines */ 69 #define OSIOP_SBCL (0x08+BL3) /* rw: SCSI Bus Control Lines */ 70 71 #define OSIOP_DSTAT (0x0c+BL0) /* ro: DMA status */ 72 #define OSIOP_SSTAT0 (0x0c+BL1) /* ro: SCSI status reg 0 */ 73 #define OSIOP_SSTAT1 (0x0c+BL2) /* ro: SCSI status reg 1 */ 74 #define OSIOP_SSTAT2 (0x0c+BL3) /* ro: SCSI status reg 2 */ 75 76 #define OSIOP_DSA 0x10 /* rw: Data Structure Address */ 77 78 #define OSIOP_CTEST0 (0x14+BL0) /* ro: Chip test register 0 */ 79 #define OSIOP_CTEST1 (0x14+BL1) /* ro: Chip test register 1 */ 80 #define OSIOP_CTEST2 (0x14+BL2) /* ro: Chip test register 2 */ 81 #define OSIOP_CTEST3 (0x14+BL3) /* ro: Chip test register 3 */ 82 83 #define OSIOP_CTEST4 (0x18+BL0) /* rw: Chip test register 4 */ 84 #define OSIOP_CTEST5 (0x18+BL1) /* rw: Chip test register 5 */ 85 #define OSIOP_CTEST6 (0x18+BL2) /* rw: Chip test register 6 */ 86 #define OSIOP_CTEST7 (0x18+BL3) /* rw: Chip test register 7 */ 87 88 #define OSIOP_TEMP 0x1c /* rw: Temporary Stack reg */ 89 90 #define OSIOP_DFIFO (0x20+BL0) /* rw: DMA FIFO */ 91 #define OSIOP_ISTAT (0x20+BL1) /* rw: Interrupt Status reg */ 92 #define OSIOP_CTEST8 (0x20+BL2) /* rw: Chip test register 8 */ 93 #define OSIOP_LCRC (0x20+BL3) /* rw: LCRC value */ 94 95 #define OSIOP_DBC 0x24 /* rw: DMA Counter reg (longword) */ 96 #define OSIOP_DBC0 (0x24+BL0) /* rw: DMA Byte Counter reg 0 */ 97 #define OSIOP_DBC1 (0x24+BL1) /* rw: DMA Byte Counter reg 1 */ 98 #define OSIOP_DBC2 (0x24+BL2) /* rw: DMA Byte Counter reg 2 */ 99 #define OSIOP_DCMD (0x24+BL3) /* rw: DMA Command Register */ 100 101 #define OSIOP_DNAD 0x28 /* rw: DMA Next Data Address */ 102 103 #define OSIOP_DSP 0x2c /* rw: DMA SCRIPTS Pointer reg */ 104 105 #define OSIOP_DSPS 0x30 /* rw: DMA SCRIPTS Pointer Save reg */ 106 107 #define OSIOP_SCRATCH 0x34 /* rw: Scratch register */ 108 109 #define OSIOP_DMODE (0x38+BL0) /* rw: DMA Mode reg */ 110 #define OSIOP_DIEN (0x38+BL1) /* rw: DMA Interrupt Enable */ 111 #define OSIOP_DWT (0x38+BL2) /* rw: DMA Watchdog Timer */ 112 #define OSIOP_DCNTL (0x38+BL3) /* rw: DMA Control reg */ 113 114 #define OSIOP_ADDER 0x3c /* ro: Adder Sum Output */ 115 116 #define OSIOP_NREGS 0x40 117 118 119 /* 120 * Register defines 121 */ 122 123 /* Scsi control register 0 (scntl0) */ 124 125 #define OSIOP_SCNTL0_ARB 0xc0 /* Arbitration mode */ 126 #define OSIOP_ARB_SIMPLE 0x00 127 #define OSIOP_ARB_FULL 0xc0 128 #define OSIOP_SCNTL0_START 0x20 /* Start Sequence */ 129 #define OSIOP_SCNTL0_WATN 0x10 /* (Select) With ATN */ 130 #define OSIOP_SCNTL0_EPC 0x08 /* Enable Parity Checking */ 131 #define OSIOP_SCNTL0_EPG 0x04 /* Enable Parity Generation */ 132 #define OSIOP_SCNTL0_AAP 0x02 /* Assert ATN on Parity Error */ 133 #define OSIOP_SCNTL0_TRG 0x01 /* Target Mode */ 134 135 /* Scsi control register 1 (scntl1) */ 136 137 #define OSIOP_SCNTL1_EXC 0x80 /* Extra Clock Cycle of data setup */ 138 #define OSIOP_SCNTL1_ADB 0x40 /* Assert Data Bus */ 139 #define OSIOP_SCNTL1_ESR 0x20 /* Enable Selection/Reselection */ 140 #define OSIOP_SCNTL1_CON 0x10 /* Connected */ 141 #define OSIOP_SCNTL1_RST 0x08 /* Assert RST */ 142 #define OSIOP_SCNTL1_AESP 0x04 /* Assert even SCSI parity */ 143 #define OSIOP_SCNTL1_PAR 0x04 /* Force bad Parity */ 144 #define OSIOP_SCNTL1_RES0 0x02 /* Reserved */ 145 #define OSIOP_SCNTL1_RES1 0x01 /* Reserved */ 146 147 /* Scsi interrupt enable register (sien) */ 148 149 #define OSIOP_SIEN_M_A 0x80 /* Phase Mismatch or ATN active */ 150 #define OSIOP_SIEN_FCMP 0x40 /* Function Complete */ 151 #define OSIOP_SIEN_STO 0x20 /* (Re)Selection timeout */ 152 #define OSIOP_SIEN_SEL 0x10 /* (Re)Selected */ 153 #define OSIOP_SIEN_SGE 0x08 /* SCSI Gross Error */ 154 #define OSIOP_SIEN_UDC 0x04 /* Unexpected Disconnect */ 155 #define OSIOP_SIEN_RST 0x02 /* RST asserted */ 156 #define OSIOP_SIEN_PAR 0x01 /* Parity Error */ 157 158 /* Scsi chip ID (scid) */ 159 160 #define OSIOP_SCID_VALUE(i) (1 << (i)) 161 162 /* Scsi transfer register (sxfer) */ 163 164 #define OSIOP_SXFER_DHP 0x80 /* Disable Halt on Parity error/ 165 ATN asserted */ 166 #define OSIOP_SXFER_TP 0x70 /* Synch Transfer Period */ 167 /* see specs for formulas: 168 Period = TCP * (4 + XFERP ) 169 TCP = 1 + CLK + 1..2; 170 */ 171 #define OSIOP_SXFER_MO 0x0f /* Synch Max Offset */ 172 #define OSIOP_MAX_OFFSET 8 173 174 /* Scsi output data latch register (sodl) */ 175 176 /* Scsi output control latch register (socl) */ 177 178 #define OSIOP_REQ 0x80 /* SCSI signal <x> asserted */ 179 #define OSIOP_ACK 0x40 180 #define OSIOP_BSY 0x20 181 #define OSIOP_SEL 0x10 182 #define OSIOP_ATN 0x08 183 #define OSIOP_MSG 0x04 184 #define OSIOP_CD 0x02 185 #define OSIOP_IO 0x01 186 187 #define OSIOP_PHASE(x) ((x) & (OSIOP_MSG|OSIOP_CD|OSIOP_IO)) 188 #define DATA_OUT_PHASE 0x00 189 #define DATA_IN_PHASE OSIOP_IO 190 #define COMMAND_PHASE OSIOP_CD 191 #define STATUS_PHASE (OSIOP_CD|OSIOP_IO) 192 #define MSG_OUT_PHASE (OSIOP_MSG|OSIOP_CD) 193 #define MSG_IN_PHASE (OSIOP_MSG|OSIOP_CD|OSIOP_IO) 194 195 /* Scsi first byte received register (sfbr) */ 196 197 /* Scsi input data latch register (sidl) */ 198 199 /* Scsi bus data lines register (sbdl) */ 200 201 /* Scsi bus control lines register (sbcl). Same as socl */ 202 203 #define OSIOP_SBCL_SSCF1 0x02 /* wo */ 204 #define OSIOP_SBCL_SSCF0 0x01 /* wo */ 205 206 /* DMA status register (dstat) */ 207 208 #define OSIOP_DSTAT_DFE 0x80 /* DMA FIFO empty */ 209 #define OSIOP_DSTAT_RES 0x40 210 #define OSIOP_DSTAT_BF 0x20 /* Bus fault */ 211 #define OSIOP_DSTAT_ABRT 0x10 /* Aborted */ 212 #define OSIOP_DSTAT_SSI 0x08 /* SCRIPT Single Step */ 213 #define OSIOP_DSTAT_SIR 0x04 /* SCRIPT Interrupt Instruction */ 214 #define OSIOP_DSTAT_WTD 0x02 /* Watchdog Timeout Detected */ 215 #define OSIOP_DSTAT_IID 0x01 /* Invalid Instruction Detected */ 216 217 /* Scsi status register 0 (sstat0) */ 218 219 #define OSIOP_SSTAT0_M_A 0x80 /* Phase Mismatch or ATN active */ 220 #define OSIOP_SSTAT0_FCMP 0x40 /* Function Complete */ 221 #define OSIOP_SSTAT0_STO 0x20 /* (Re)Selection timeout */ 222 #define OSIOP_SSTAT0_SEL 0x10 /* (Re)Selected */ 223 #define OSIOP_SSTAT0_SGE 0x08 /* SCSI Gross Error */ 224 #define OSIOP_SSTAT0_UDC 0x04 /* Unexpected Disconnect */ 225 #define OSIOP_SSTAT0_RST 0x02 /* RST asserted */ 226 #define OSIOP_SSTAT0_PAR 0x01 /* Parity Error */ 227 228 /* Scsi status register 1 (sstat1) */ 229 230 #define OSIOP_SSTAT1_ILF 0x80 /* Input latch (sidl) full */ 231 #define OSIOP_SSTAT1_ORF 0x40 /* output reg (sodr) full */ 232 #define OSIOP_SSTAT1_OLF 0x20 /* output latch (sodl) full */ 233 #define OSIOP_SSTAT1_AIP 0x10 /* Arbitration in progress */ 234 #define OSIOP_SSTAT1_LOA 0x08 /* Lost arbitration */ 235 #define OSIOP_SSTAT1_WOA 0x04 /* Won arbitration */ 236 #define OSIOP_SSTAT1_RST 0x02 /* SCSI RST current value */ 237 #define OSIOP_SSTAT1_SDP 0x01 /* SCSI SDP current value */ 238 239 /* Scsi status register 2 (sstat2) */ 240 241 #define OSIOP_SSTAT2_FF 0xf0 /* SCSI FIFO flags (bytecount) */ 242 #define OSIOP_SCSI_FIFO_DEEP 8 243 #define OSIOP_SSTAT2_SDP 0x08 /* Latched (on REQ) SCSI SDP */ 244 #define OSIOP_SSTAT2_MSG 0x04 /* Latched SCSI phase */ 245 #define OSIOP_SSTAT2_CD 0x02 246 #define OSIOP_SSTAT2_IO 0x01 247 248 /* Chip test register 0 (ctest0) */ 249 250 #define OSIOP_CTEST0_RES0 0x80 251 #define OSIOP_CTEST0_BTD 0x40 /* Byte-to-byte Timer Disable */ 252 #define OSIOP_CTEST0_GRP 0x20 /* Generate Receive Parity */ 253 #define OSIOP_CTEST0_EAN 0x10 /* Enable Active Negation */ 254 #define OSIOP_CTEST0_HSC 0x08 /* Halt SCSI clock */ 255 #define OSIOP_CTEST0_ERF 0x04 /* Extend REQ/ACK Filtering */ 256 #define OSIOP_CTEST0_RES1 0x02 257 #define OSIOP_CTEST0_DDIR 0x01 /* Xfer direction (1-> from SCSI bus) */ 258 259 260 /* Chip test register 1 (ctest1) */ 261 262 #define OSIOP_CTEST1_FMT 0xf0 /* Byte empty in DMA FIFO bottom 263 (high->byte3) */ 264 #define OSIOP_CTEST1_FFL 0x0f /* Byte full in DMA FIFO top, same */ 265 266 /* Chip test register 2 (ctest2) */ 267 268 #define OSIOP_CTEST2_RES 0x80 269 #define OSIOP_CTEST2_SIGP 0x40 /* Signal process */ 270 #define OSIOP_CTEST2_SOFF 0x20 /* Synch Offset compare 271 (1-> zero Init, max Tgt */ 272 #define OSIOP_CTEST2_SFP 0x10 /* SCSI FIFO Parity */ 273 #define OSIOP_CTEST2_DFP 0x08 /* DMA FIFO Parity */ 274 #define OSIOP_CTEST2_TEOP 0x04 /* True EOP (a-la 5380) */ 275 #define OSIOP_CTEST2_DREQ 0x02 /* DREQ status */ 276 #define OSIOP_CTEST2_DACK 0x01 /* DACK status */ 277 278 /* Chip test register 3 (ctest3) read-only, top of SCSI FIFO */ 279 280 /* Chip test register 4 (ctest4) */ 281 282 #define OSIOP_CTEST4_MUX 0x80 /* Host bus multiplex mode */ 283 #define OSIOP_CTEST4_ZMOD 0x40 /* High-impedance outputs */ 284 #define OSIOP_CTEST4_SZM 0x20 /* ditto, SCSI "outputs" */ 285 #define OSIOP_CTEST4_SLBE 0x10 /* SCSI loopback enable */ 286 #define OSIOP_CTEST4_SFWR 0x08 /* SCSI FIFO write enable (from sodl) */ 287 #define OSIOP_CTEST4_FBL 0x07 /* DMA FIFO Byte Lane select 288 (from ctest6) 4->0, .. 7->3 */ 289 290 /* Chip test register 5 (ctest5) */ 291 292 #define OSIOP_CTEST5_ADCK 0x80 /* Clock Address Incrementor */ 293 #define OSIOP_CTEST5_BBCK 0x40 /* Clock Byte counter */ 294 #define OSIOP_CTEST5_ROFF 0x20 /* Reset SCSI offset */ 295 #define OSIOP_CTEST5_MASR 0x10 /* Master set/reset pulses 296 (of bits 3-0) */ 297 #define OSIOP_CTEST5_DDIR 0x08 /* (re)set internal DMA direction */ 298 #define OSIOP_CTEST5_EOP 0x04 /* (re)set internal EOP */ 299 #define OSIOP_CTEST5_DREQ 0x02 /* (re)set internal REQ */ 300 #define OSIOP_CTEST5_DACK 0x01 /* (re)set internal ACK */ 301 302 /* Chip test register 6 (ctest6) DMA FIFO access */ 303 304 /* Chip test register 7 (ctest7) */ 305 306 #define OSIOP_CTEST7_CDIS 0x80 /* Cache burst disable */ 307 #define OSIOP_CTEST7_SC1 0x40 /* Snoop control 1 */ 308 #define OSIOP_CTEST7_SC0 0x20 /* Snoop control 0 */ 309 #define OSIOP_CTEST7_STD 0x10 /* Selection timeout disable */ 310 #define OSIOP_CTEST7_DFP 0x08 /* DMA FIFO parity bit */ 311 #define OSIOP_CTEST7_EVP 0x04 /* Even parity (to host bus) */ 312 #define OSIOP_CTEST7_TT1 0x02 /* Transfer type bit */ 313 #define OSIOP_CTEST7_DIFF 0x01 /* Differential mode */ 314 315 /* DMA FIFO register (dfifo) */ 316 317 #define OSIOP_DFIFO_FLF 0x80 /* Flush (spill) DMA FIFO */ 318 #define OSIOP_DFIFO_BO 0x7f /* FIFO byte offset counter */ 319 320 /* Interrupt status register (istat) */ 321 322 #define OSIOP_ISTAT_ABRT 0x80 /* Abort operation */ 323 #define OSIOP_ISTAT_RST 0x40 /* Software reset */ 324 #define OSIOP_ISTAT_SIGP 0x20 /* Signal process */ 325 #define OSIOP_ISTAT_RES 0x10 326 #define OSIOP_ISTAT_CON 0x08 /* Connected */ 327 #define OSIOP_ISTAT_RES1 0x04 328 #define OSIOP_ISTAT_SIP 0x02 /* SCSI Interrupt pending */ 329 #define OSIOP_ISTAT_DIP 0x01 /* DMA Interrupt pending */ 330 331 /* Chip test register 8 (ctest8) */ 332 333 #define OSIOP_CTEST8_V 0xf0 /* Chip revision level */ 334 #define OSIOP_CTEST8_FLF 0x08 /* Flush DMA FIFO */ 335 #define OSIOP_CTEST8_CLF 0x04 /* Clear DMA and SCSI FIFOs */ 336 #define OSIOP_CTEST8_FM 0x02 /* Fetch pin mode */ 337 #define OSIOP_CTEST8_SM 0x01 /* Snoop pins mode */ 338 339 /* DMA Mode register (dmode) */ 340 341 #define OSIOP_DMODE_BL_MASK 0xc0 /* DMA burst length */ 342 #define OSIOP_DMODE_BL8 0xc0 /* 8 bytes */ 343 #define OSIOP_DMODE_BL4 0x80 /* 4 bytes */ 344 #define OSIOP_DMODE_BL2 0x40 /* 2 bytes */ 345 #define OSIOP_DMODE_BL1 0x00 /* 1 byte */ 346 #define OSIOP_DMODE_FC 0x30 /* Function code */ 347 #define OSIOP_DMODE_PD 0x08 /* Program/data */ 348 #define OSIOP_DMODE_FAM 0x04 /* fixed address mode */ 349 #define OSIOP_DMODE_U0 0x02 /* User programmable transfer type */ 350 #define OSIOP_DMODE_MAN 0x01 /* SCRIPTS in Manual start mode */ 351 352 /* DMA interrupt enable register (dien) */ 353 354 #define OSIOP_DIEN_RES 0xc0 355 #define OSIOP_DIEN_BF 0x20 /* On Bus Fault */ 356 #define OSIOP_DIEN_ABRT 0x10 /* On Abort */ 357 #define OSIOP_DIEN_SSI 0x08 /* On SCRIPTS sstep */ 358 #define OSIOP_DIEN_SIR 0x04 /* On SCRIPTS intr instruction */ 359 #define OSIOP_DIEN_WTD 0x02 /* On watchdog timeout */ 360 #define OSIOP_DIEN_IID 0x01 /* On illegal instruction detected */ 361 362 /* DMA control register (dcntl) */ 363 364 #define OSIOP_DCNTL_CF_MASK 0xc0 /* Clock frequency dividers: */ 365 #define OSIOP_DCNTL_CF_2 0x00 /* 0 --> 37.51..50.00 MHz, div=2 */ 366 #define OSIOP_DCNTL_CF_1_5 0x40 /* 1 --> 25.01..37.50 MHz, div=1.5 */ 367 #define OSIOP_DCNTL_CF_1 0x80 /* 2 --> 16.67..25.00 MHz, div=1 */ 368 #define OSIOP_DCNTL_CF_3 0xc0 /* 3 --> 50.01..66.67 MHz, div=3 */ 369 #define OSIOP_DCNTL_EA 0x20 /* Enable ACK */ 370 #define OSIOP_DCNTL_SSM 0x10 /* Single step mode */ 371 #define OSIOP_DCNTL_LLM 0x08 /* Enable SCSI Low-level mode */ 372 #define OSIOP_DCNTL_STD 0x04 /* Start DMA operation */ 373 #define OSIOP_DCNTL_FA 0x02 /* Fast arbitration */ 374 #define OSIOP_DCNTL_COM 0x01 /* 53C700 Compatibility */ 375
Indexes created Sun Sep 21 16:09:51 GMT 2025