1 /* $NetBSD: ihareg.h,v 1.9 2008/05/03 05:21:25 tsutsui Exp $ */ 2 3 /*- 4 * Device driver for the INI-9XXXU/UW or INIC-940/950 PCI SCSI Controller. 5 * 6 * Written for 386bsd and FreeBSD by 7 * Winston Hung <winstonh (at) initio.com> 8 * 9 * Copyright (c) 1997-1999 Initio Corp. 10 * Copyright (c) 2000 Ken Westerback 11 * All rights reserved. 12 * 13 * Redistribution and use in source and binary forms, with or without 14 * modification, are permitted provided that the following conditions 15 * are met: 16 * 1. Redistributions of source code must retain the above copyright 17 * notice, this list of conditions and the following disclaimer, 18 * without modification, immediately at the beginning of the file. 19 * 2. The name of the author may not be used to endorse or promote products 20 * derived from this software without specific prior written permission. 21 * 22 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 23 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 24 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 25 * IN NO EVENT SHALL THE AUTHOR OR HIS RELATIVES BE LIABLE FOR ANY DIRECT, 26 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES 27 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 28 * SERVICES; LOSS OF MIND, USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 29 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 30 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING 31 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 32 * THE POSSIBILITY OF SUCH DAMAGE. 33 */ 34 35 /* 36 * Ported to NetBSD by Izumi Tsutsui <tsutsui (at) NetBSD.org> from OpenBSD: 37 * $OpenBSD: iha.h,v 1.2 2001/02/08 17:35:05 krw Exp $ 38 */ 39 40 /* 41 * Tulip (aka inic-940/950) PCI Configuration Space Initio Specific Registers 42 * 43 * Offsets 0x00 through 0x3f are the standard PCI Configuration Header 44 * registers. 45 * 46 * Offsets 0x40 through 0x4f, 0x51, 0x53, 0x57, 0x5b, 0x5e and 0x5f are 47 * reserved registers. 48 * 49 * Registers 0x50 and 0x52 always read as 0. 50 * 51 * The register offset names and associated bit field names are taken 52 * from the Inic-950 Data Sheet, Version 2.1, March 1997 53 */ 54 #define TUL_GCTRL0 0x54 /* R/W Global Control 0 */ 55 #define EEPRG 0x04 /* Enable EEPROM Programming */ 56 #define TUL_GCTRL1 0x55 /* R/W Global Control 1 */ 57 #define ATDEN 0x01 /* Auto Termination Detect Enable */ 58 #define TUL_GSTAT 0x56 /* R/W Global Status - connector type */ 59 #define TUL_EPAD0 0x58 /* R/W External EEPROM Addr (lo byte) */ 60 #define TUL_EPAD1 0x59 /* R/W External EEPROM Addr (hi byte) */ 61 #define TUL_PNVPG 0x5A /* R/W Data port to external BIOS */ 62 #define TUL_EPDATA 0x5C /* R/W EEPROM Data port */ 63 #define TUL_NVRAM 0x5D /* R/W Non-volatile RAM port */ 64 #define READ 0x80 /* Read from given NVRAM addr */ 65 #define WRITE 0x40 /* Write to given NVRAM addr */ 66 #define ENABLE_ERASE 0x30 /* Enable NVRAM Erase/Write */ 67 #define NVRCS 0x08 /* Select external NVRAM */ 68 #define NVRCK 0x04 /* NVRAM Clock */ 69 #define NVRDO 0x02 /* NVRAM Write Data */ 70 #define NVRDI 0x01 /* NVRAM Read Data */ 71 72 /* 73 * Tulip (aka inic-940/950) SCSI Registers 74 */ 75 #define TUL_STCNT0 0x80 /* R/W 24 bit SCSI Xfer Count */ 76 #define TCNT 0x00ffffff /* SCSI Xfer Transfer Count */ 77 #define TUL_SFIFOCNT 0x83 /* R/W 5 bit FIFO counter */ 78 #define FIFOC 0x1f /* SCSI Offset Fifo Count */ 79 #define TUL_SISTAT 0x84 /* R Interrupt Register */ 80 #define RSELED 0x80 /* Reselected */ 81 #define STIMEO 0x40 /* Selected/Reselected Timeout */ 82 #define SBSRV 0x20 /* SCSI Bus Service */ 83 #define SRSTD 0x10 /* SCSI Reset Detected */ 84 #define DISCD 0x08 /* Disconnected Status */ 85 #define SELED 0x04 /* Select Interrupt */ 86 #define SCAMSCT 0x02 /* SCAM selected */ 87 #define SCMDN 0x01 /* Command Complete */ 88 #define TUL_SIEN 0x84 /* W Interrupt enable */ 89 #define ALL_INTERRUPTS 0xff 90 #define TUL_STAT0 0x85 /* R Status 0 */ 91 #define INTPD 0x80 /* Interrupt pending */ 92 #define SQACT 0x40 /* Sequencer active */ 93 #define XFCZ 0x20 /* Xfer counter zero */ 94 #define SFEMP 0x10 /* FIFO empty */ 95 #define SPERR 0x08 /* SCSI parity error */ 96 #define PH_MASK 0x07 /* SCSI phase mask */ 97 #define TUL_SCTRL0 0x85 /* W Control 0 */ 98 #define RSSQC 0x20 /* Reset sequence counter */ 99 #define RSFIFO 0x10 /* Flush FIFO */ 100 #define CMDAB 0x04 /* Abort command (sequence) */ 101 #define RSMOD 0x02 /* Reset SCSI Chip */ 102 #define RSCSI 0x01 /* Reset SCSI Bus */ 103 #define TUL_STAT1 0x86 /* R Status 1 */ 104 #define STRCV 0x80 /* Status received */ 105 #define MSGST 0x40 /* Message sent */ 106 #define CPDNE 0x20 /* Data phase done */ 107 #define DPHDN 0x10 /* Data phase done */ 108 #define STSNT 0x08 /* Status sent */ 109 #define SXCMP 0x04 /* Xfer completed */ 110 #define SLCMP 0x02 /* Selection completed */ 111 #define ARBCMP 0x01 /* Arbitration completed */ 112 #define TUL_SCTRL1 0x86 /* W Control 1 */ 113 #define ENSCAM 0x80 /* Enable SCAM */ 114 #define NIDARB 0x40 /* No ID for Arbitration */ 115 #define ENLRS 0x20 /* Low Level Reselect */ 116 #define PWDN 0x10 /* Power down mode */ 117 #define WCPU 0x08 /* Wide CPU */ 118 #define EHRSL 0x04 /* Enable HW reselect */ 119 #define ESBUSOUT 0x02 /* Enable SCSI data bus out latch */ 120 #define ESBUSIN 0x01 /* Enable SCSI data bus in latch */ 121 #define TUL_SSTATUS2 0x87 /* R Status 2 */ 122 #define SABRT 0x80 /* Command aborted */ 123 #define OSCZ 0x40 /* Offset counter zero */ 124 #define SFFUL 0x20 /* FIFO full */ 125 #define TMCZ 0x10 /* Timeout counter zero */ 126 #define BSYGN 0x08 /* Busy release */ 127 #define PHMIS 0x04 /* Phase mismatch */ 128 #define SBEN 0x02 /* SCSI data bus enable */ 129 #define SRST 0x01 /* SCSI bus reset in progress */ 130 #define TUL_SCONFIG0 0x87 /* W Configuration */ 131 #define PHLAT 0x80 /* Enable phase latch */ 132 #define ITMOD 0x40 /* Initiator mode */ 133 #define SPCHK 0x20 /* Enable SCSI parity */ 134 #define ADMA8 0x10 /* Alternate dma 8-bits mode */ 135 #define ADMAW 0x08 /* Alternate dma 16-bits mode */ 136 #define EDACK 0x04 /* Enable DACK in wide SCSI xfer */ 137 #define ALTPD 0x02 /* Alternate sync period mode */ 138 #define DSRST 0x01 /* Disable SCSI Reset signal */ 139 #define SCONFIG0DEFAULT (PHLAT | ITMOD | ALTPD | DSRST) 140 #define TUL_SOFSC 0x88 /* R Offset */ 141 #define PERIOD_WIDE_SCSI 0x80 /* Enable Wide SCSI */ 142 #define PERIOD_SYXPD 0x70 /* Synch. SCSI Xfer rate */ 143 #define PERIOD_SYOFS 0x0f /* Synch. SCSI Offset */ 144 #define TUL_SYNCM 0x88 /* W Sync. Xfer Period & Offset */ 145 #define TUL_SBID 0x89 /* R SCSI BUS ID */ 146 #define TUL_SID 0x89 /* W SCSI ID */ 147 #define TUL_SALVC 0x8A /* R FIFO Avail Cnt/Identify Msg */ 148 #define IHA_MSG_IDENTIFY_LUNMASK 0x07 149 #define TUL_STIMO 0x8A /* W Sel/Resel Time Out Register */ 150 #define STIMO_250MS 153 /* in units of 1.6385us */ 151 #define TUL_SDATI 0x8B /* R SCSI Bus contents */ 152 #define TUL_SDAT0 0x8B /* W SCSI Data Out */ 153 #define TUL_SFIFO 0x8C /* R/W FIFO */ 154 #define TUL_SSIGI 0x90 /* R SCSI signal in */ 155 #define REQ 0x80 /* REQ signal */ 156 #define ACK 0x40 /* ACK signal */ 157 #define BSY 0x20 /* BSY signal */ 158 #define SEL 0x10 /* SEL signal */ 159 #define ATN 0x08 /* ATN signal */ 160 #define MSG 0x04 /* MSG signal */ 161 #define CD 0x02 /* C/D signal */ 162 #define IO 0x01 /* I/O signal */ 163 #define TUL_SSIGO 0x90 /* W SCSI signal out */ 164 #define TUL_SCMD 0x91 /* R/W SCSI Command */ 165 #define NO_OP 0x00 /* Place Holder for tulip_wait() */ 166 #define SEL_NOATN 0x01 /* Select w/o ATN Sequence */ 167 #define XF_FIFO_OUT 0x03 /* FIFO Xfer Information out */ 168 #define MSG_ACCEPT 0x0F /* Message Accept */ 169 #define SEL_ATN 0x11 /* Select w ATN Sequence */ 170 #define SEL_ATNSTOP 0x12 /* Select w ATN & Stop Sequence */ 171 #define SELATNSTOP 0x1E /* Select w ATN & Stop Sequence */ 172 #define SEL_ATN3 0x31 /* Select w ATN3 Sequence */ 173 #define XF_DMA_OUT 0x43 /* DMA Xfer Information out */ 174 #define EN_RESEL 0x80 /* Enable Reselection */ 175 #define XF_FIFO_IN 0x83 /* FIFO Xfer Information in */ 176 #define CMD_COMP 0x84 /* Command Complete Sequence */ 177 #define XF_DMA_IN 0xC3 /* DMA Xfer Information in */ 178 #define TUL_STEST0 0x92 /* R/W Test0 */ 179 #define TUL_STEST1 0x93 /* R/W Test1 */ 180 181 /* 182 * Tulip (aka inic-940/950) DMA Registers 183 */ 184 #define TUL_DXPA 0xC0 /* R/W DMA Xfer Physcl Addr 0-31*/ 185 #define TUL_DXPAE 0xC4 /* R/W DMA Xfer Physcl Addr 32-63*/ 186 #define TUL_DCXA 0xC8 /* R DMA Curr Xfer Physcl Addr 0-31*/ 187 #define TUL_DCXAE 0xCC /* R DMA Curr Xfer Physcl Addr 32-63*/ 188 #define TUL_DXC 0xD0 /* R/W DMA Xfer Counter */ 189 #define TUL_DCXC 0xD4 /* R DMA Current Xfer Counter */ 190 #define TUL_DCMD 0xD8 /* R/W DMA Command Register */ 191 #define SGXFR 0x80 /* Scatter/Gather Xfer */ 192 #define RSVD 0x40 /* Reserved - always reads as 0 */ 193 #define XDIR 0x20 /* Xfer Direction 0/1 = out/in */ 194 #define BMTST 0x10 /* Bus Master Test */ 195 #define CLFIFO 0x08 /* Clear FIFO */ 196 #define ABTXFR 0x04 /* Abort Xfer */ 197 #define FRXFR 0x02 /* Force Xfer */ 198 #define STRXFR 0x01 /* Start Xfer */ 199 #define TUL_ISTUS0 0xDC /* R/W Interrupt Status Register */ 200 #define DGINT 0x80 /* DMA Global Interrupt */ 201 #define RSVRD0 0x40 /* Reserved */ 202 #define RSVRD1 0x20 /* Reserved */ 203 #define SCMP 0x10 /* SCSI Complete */ 204 #define PXERR 0x08 /* PCI Xfer Error */ 205 #define DABT 0x04 /* DMA Xfer Aborted */ 206 #define FXCMP 0x02 /* Forced Xfer Complete */ 207 #define XCMP 0x01 /* Bus Master Xfer Complete */ 208 #define TUL_ISTUS1 0xDD /* R DMA status Register */ 209 #define SCBSY 0x08 /* SCSI Busy */ 210 #define FFULL 0x04 /* FIFO Full */ 211 #define FEMPT 0x02 /* FIFO Empty */ 212 #define XPEND 0x01 /* Xfer pending */ 213 #define TUL_IMSK 0xE0 /* R/W Interrupt Mask Register */ 214 #define MSCMP 0x10 /* Mask SCSI Complete */ 215 #define MPXFER 0x08 /* Mask PCI Xfer Error */ 216 #define MDABT 0x04 /* Mask Bus Master Abort */ 217 #define MFCMP 0x02 /* Mask Force Xfer Complete */ 218 #define MXCMP 0x01 /* Mask Bus Master Xfer Complete */ 219 #define MASK_ALL (MXCMP | MFCMP | MDABT | MPXFER | MSCMP) 220 #define TUL_DCTRL0 0xE4 /* R/W DMA Control Register */ 221 #define SXSTP 0x80 /* SCSI Xfer Stop */ 222 #define RPMOD 0x40 /* Reset PCI Module */ 223 #define RSVRD2 0x20 /* SCSI Xfer Stop */ 224 #define PWDWN 0x10 /* Power Down */ 225 #define ENTM 0x08 /* Enable SCSI Terminator Low */ 226 #define ENTMW 0x04 /* Enable SCSI Terminator High */ 227 #define DISAFC 0x02 /* Disable Auto Clear */ 228 #define LEDCTL 0x01 /* LED Control */ 229 #define TUL_DCTRL1 0xE5 /* R/W DMA Control Register 1 */ 230 #define SDWS 0x01 /* SCSI DMA Wait State */ 231 #define TUL_DFIFO 0xE8 /* R/W DMA FIFO */ 232 233 #define TUL_WCTRL 0xF7 /* ?/? Bus master wait state control */ 234 #define TUL_DCTRL 0xFB /* ?/? DMA delay control */ 235
Indexes created Sat Sep 20 22:09:52 GMT 2025