xref: /src/distrib/notes/amiga/upgrade

The upgrade to NetBSD 1.2 is a binary upgrade; it would be prohibitive
to make users upgrade by compiling and installing the 1.2 sources, and
it would be very difficult to even compile a set of instructions that
allowed them to do so.  Because of the various changes to the system,
it is impractical to upgrade by recompiling from the sources and
installing.

To do the upgrade, you must have the NetBSD kernel on AmigaDOS and
you must transfer the upgrade file system upgr-12.fs onto the swap
partition of the NetBSD hard disk.  You must also have at least the
"base12" binary distribution set available, so that you can upgrade
with it, using one of the upgrade methods described above.  Finally,
you must have sufficient disk space available to install the new
binaries.  Since the old binaries are being overwritten in place,
you only need space for the new binaries, which weren't previously
on the system.  If you have a few megabytes free on each of your
root and /usr partitions, you should have enough space.

Since upgrading involves replacing the kernel, and most of the system
binaries, it has the potential to cause data loss.  You are strongly
advised to BACK UP ANY IMPORTANT DATA ON YOUR DISK, whether on the
NetBSD partition or on another operating system's partition, before
beginning the upgrade process.

To upgrade your system, follow the following instructions:

	Transfer the upgrade miniroot file system onto the hard disk
	partition used by NetBSD for swapping, as described in the
	"Preparing your System for NetBSD Installation" section above.

	Now boot up NetBSD using the 1.2 kernel using the loadbsd
	command:

		loadbsd -b netbsd

	If you machine has a split memory space, like, e.g., DraCo
	machines, use this instead:

		loadbsd -bn2 netbsd

	* Directly booting NetBSD, with boot blocks installed:

	[This description is for V41 (OS 3.1) ROMs. For older ROMs,
	there might be small differences. Check your AmigaOS documentation
	to learn about the exact procedure.]

	Reboot your machine, holding down both mouse buttons if you
	have a 2-button mouse, the outer mouse buttons if you have
	a 3-button mouse. On the DraCo, press the left mouse button
	instead, when the boot screen prompts you for it.

	From the boot menu, select "Boot Options".
	Select the swap partition with the miniroot, and then "ok".
	Select "Boot" now. The machine will boot the bootblock, which
	will prompt your for a command line. You have a few seconds time
	to change the default. Entering an empty line will accept the
	default.

	The bootblock uses command lines of the form:

	file options

	where file is the kernel file name on the partition where the
	boot block is on, and options are the same as with loadbsd.
	E.g., instead of "loadbsd -bsSn2 netbsd" use "netbsd -bsSn2".

	* Once your kernel boots:

	You should see the screen clear and some information about
	your system as the kernel configures the hardware.  Note which
	hard disk device is configured that contains your root and
	swap partition.  When prompted for the root device, type
	'sd0*' (replacing 0 with the disk number that NetBSD used for
	your root/swap device).  The '*' character indicates that the
	root file system is contained on the swap partition.
	When you reach the prompt asking you for a shell name, just
	hit return.

	You will be presented with some information about the upgrade
	process and a warning message, and will be asked if you wish
	to proceed with the upgrade process.  If you answer
	negatively, the upgrade process will stop, and your disk will
	not be modified.  If you answer affirmatively, the upgrade
	process will begin, and your disk will be modified.  You may
	hit Control-C to stop the upgrade process at any time.
	However, if you hit it at an inopportune moment, your system
	may be left in an inconsistent (and possibly unusable) state.

	You will be asked if you wish to upgrade your file systems to
	the new file system format.  If you do, reply affirmatively.
	If you don't have your file systems upgraded now, you should
	probably do it manually after the install process is complete,
	by using "fsck -c 2". Read the fsck(8) manual page for more
	details.

	The upgrade program will then check your root file system,
	and, if you approved, will upgrade it to the new file system
	format.  It will then mount your root file system on /mnt.

	If your file systems are being upgraded, the upgrade script
	will copy the new fsck(8) program to your hard disk and
	upgrade your remaining file systems.

	The upgrade program will then mount all of your file systems
	under /mnt.  (In other words, your root partition will be
	mounted on /mnt, your /usr partition on /mnt/usr, etc.)

	If you don't already have the NetBSD distribution sets on your
	disk, look in the installation section for information on how
	to transfer them to your disk.

	Once the distribution sets are transferred to your disk,
	continue here.  (Obviously, if the NetBSD distribution sets
	are already on your disk, because you've transferred them
	before starting the upgrade process, you don't need to
	transfer them again now!)

	After the software has been transferred to the machine (or
	mounted, in the case of upgrading via NFS), change into the
	directory containing the "base12" distribution set.  Once you
	are there, run the "Set_tmp_dir" command, and hit return at
	the prompt to select the default answer for the temporary
	directory's path name.  (It should be the path name of the
	directory that you're in.)

	Run the command "Extract base12" to upgrade the base
	distribution.

	Repeat the above two steps for all of the sets you wish to
	upgrade.  (For each, change into the directory containing the
	set, run "Set_tmp_dir" and accept the default path name, then
	run the "Extract <setname>" command.)

	If you were previously using the security distribution set,
	you MUST upgrade to the new version, or you will not be able
	to log in when the upgrade process is complete.  Similarly, if
	you were not previously using the security set, you must NOT
	upgrade to the new version.

	When you are done upgrading all of the distribution sets you
	wish to upgrade, issue the command "Cleanup".  It will clean
	up the installation, by remaking some system databases, and 
	install the kernel and a bootblock onto the root partition.
	When it is complete, you should use "halt" to halt the system.

Your system has now been upgraded to NetBSD 1.2.

	After a new kernel has been copied to your hard disk, your
	machine is a complete NetBSD 1.2 system.  However, that
	doesn't mean that you're finished with the upgrade process.
	There are several things that you should do, or might have to
	do, to insure that the system works properly.

	First, if you did not upgrade your file systems to the new
	file system format during the upgrade process, you may want to
	do so now, with "fsck -c 2".  If you are unsure about the
	process, it's suggested that you read the fsck(8) manual page.

	Second, you will probably want to get the etc12 distribution,
	extract it, and compare its contents with those in your /etc/
	directory.  You will probably want to replace some of your
	system configuration files, or incorporate some of the changes
	in the new versions into yours.

	Third, you will probably want to update the set of device
	nodes you have in /dev.  If you've changed the contents of
	/dev by hand, you will need to be careful about this, but if
	not, you can just cd into /dev, and run the command "sh
	MAKEDEV all".

	Fourth, you must deal with certain changes in the formats of
	some of the configuration files.  The most notable change is
	that the "options" given to many of the file systems in
	/etc/fstab or by hand have changed, and some of the file
	systems have changed names.  To find out what the new options
	are, it's suggested that you read the manual page for the file
	systems' mount commands, for example mount_nfs(8) for NFS.
	(Note that the information for mounts of type "ffs", i.e. Fast
	File Systems, are contained in the mount_ffs(8) man page.)

	Finally, you will want to delete old binaries that were part
	of the version of NetBSD that you upgraded from and have since
	been removed from the NetBSD distribution.  If upgrading from
	a NetBSD version older than 1.0, you might also want to
	recompile any locally-built binaries, to take advantage of the
	shared libraries.  (Note that any new binaries that you build
	will be dynamically linked, and therefore take advantage of
	the shared libraries, by default.  For information on how to
	make statically linked binaries, see the cc(1) and ld(1)
	manual pages.)