. .Nx*M \*V will run on most HP 9000/300- and 400-series machines. The smallest amount of RAM that has been tested is 4 MB. If you wish to run X, more RAM is recommended.
p Here is a table of recommended HD partition sizes for a full install: l -column -offset indent Partition Suggested Needed t Partition Ta Suggested Ta Needed t / (root) Ta "25 MB" Ta "15 MB" t /usr Ta "150 MB" Ta "100 MB" t /var Ta "20 MB" Ta "5 MB" t swap Ta Em "2-3 *RAM" Ta 6 MB .El .(item -offset indent Anything else is up to you! .item)
p .(Note The \*M installation procedure uses a .Em miniroot file system which is placed into the swap area of the disk. The swap partition must be large enough to hold this miniroot image. .Note) . .Ss2 Supported hardware .(bullet -offset indent CPUs .(bullet -compact 318 (16 MHz 68020, with built-in monochrome framebuffer, no expansion) t 319 (16 MHz 68020, with built-in 6 bit color framebuffer, no expansion) t 320 (16 MHz 68020, 16 KB L2 cache, up to 7.5 MB RAM) .Em "Requires Human Interface board" t 330 (16 MHz 68020, 4 MB on motherboard, up to 8 MB RAM) .Em "Requires Human Interface board" t 340 (16 MHz 68030, up to 16 MB RAM) t 345 (50 MHz 68030 with 32 KB L2 cache, up to 128 MB RAM, built-in SCSI) t 350 (25 MHz 68020, 32 KB L2 cache, up to 48 MB RAM) .Em "Requires Human Interface board" t 360 (25 MHz 68030, with 4 MB RAM built-in, up to 48 MB RAM) .Em "Requires System Interface board" t 362 (25 MHz 68030) .Em "Requires System Interface board" .Em "Framebuffer is unsupported, you must use a serial console" t 370 (33 MHz 68030, 64 KB L2 cache, up to 48 MB RAM) .Em "Requires System Interface board" t 375 (50 MHz 68030 with 32 KB L2 cache, up to 128 MB RAM, built-in SCSI) t 380 (25 MHz 68040, up to 128 MB RAM, built-in SCSI) t 382 (25 MHz 68040, built-in SCSI) .Em "Framebuffer is unsupported, you must use a serial console" t 385 (33 MHz 68040, up to 128 MB RAM, built-in SCSI) t 400s, 400t, 400dl (50 MHz 68030 with 32 KB L2 cache, built-in SCSI, up to 128 MB RAM) t 425s, 425t, 425dl (25 MHz 68040 with built-in SCSI, up to 128 MB RAM) t 425e (25 MHz 68040, built-in SCSI) .Em "The BootROM does not support serial console and" .Nx*M .Em "does not support the 425e framebuffer. When the" .Nx .Em "kernel begins to boot it will default to using the serial port for console" t 433s, 433t, 433dl (33 MHz 68040 with built-in SCSI, up to 128 MB RAM) .bullet) t HP-IB devices .(bullet -compact .Em rd ; CS80 disks: 2200, 2203, 7912, 7914, 7933, 7936, 7937, 7945, 7946, 7957, 7958, and 7959 t .Em rd ; CS80 floppy disks: 9122, 9134 (possibly others) .Em "Requires use of HP-UX LIF utilities via HP-UX emulation" t .Em ct ; CS80 Low-density 16 track cartridge (67 MB): 7912, 7914, 7946, and 9144 .Em "Cannot read or write to 32 track tapes" t .Em ct ; CS80 High-density 32 track cartridge (134 MB): 9145 .Em "Cannot write to 16 track tapes (read only)" t .Em mt ; CS80 Half-inch tape: 7974A, 7978A/B, 7979A, 7980A, and 7980XC. .bullet) t SCSI devices .(bullet -compact .Em sd ; SCSI hard drives .Em "Some SCSI II drives may have problems (not very common)" t .Em sd ; SCSI CD-ROM drives .Em "Support for data only (no audio CDs)" t .Em sd ; SCSI Magneto-optical drives t .Em st ; SCSI tape drives: HP 35450A (DDS-1 DAT), Exabyte EXB-8200 (8mm), Archive (QIC-24), Archive Viper (QIC-60), Archive Viper (QIC-150), Archive Python 25501 (DAT), and Archive Python 28849 (DAT) t .Em ac ; SCSI autochangers .bullet) t Serial interfaces (see the FAQ for more detailed specs and information on configuring: .Lk http://www.netbsd.org/Ports/hp300/faq.html#serialinfo .(bullet -compact .Em dca ; Built-in single serial port on System Interface board and Human Interface board t .Em apci ; Built-in Apollo 4-port on Series 400 workstations t .Em dcm ; 98638 8-port (DIO-II board, appears to kernel as two 98642 devices) t .Em dcm ; 98642 4-port (DIO-I board) t .Em dca ; 98626, 98644 built-in or add-on (DIO-I board) single serial port t .Em dcl ; 98628A single port (DIO-I board) .bullet) t Network interfaces .(bullet -compact .Em le ; 98643 built-in and add-on (DIO-I board) ethernet cards. .bullet) t Graphics Devices .(bullet -compact 98544 monochrome Topcat (1024x768, 1 bit, DIO-II) t 98545A color Topcat (1024x768, 4 bits, DIO-II) t 98547 color Topcat (1024x768, 6 bits) t 98548A monochrome Catseye (1024x768, 1 bit) t 98549A color Catseye (1024x768, 6 bits) t 98550A Catseye Hi-Res Color (a.k.a. CH) (1280x1024 @ 60 Hz, 8 bits, DIO-II) t 98700 and 98710 Gatorbox (1280x1024 @ 60 Hz, 4 or 8 bits) .Em "Requires 98287 (DIO-I board) to connect to workstation" t 98720 and 98721 color Renaissance SRX (1280x1024 @ 60 Hz, 8, 12 or 24 bits) .Em "Requires 98724 (DIO-I board) or 98725 (DIO-II board) to connect to workstation" t 98730 and 98731 DaVinci TurboSRX (1280x1024 @ 60 Hz, 8, 16, or 24 bits) .Em "Requires 98726A (DIO-II board) to connect to workstation" t A1096A monochrome Hyperion (1280x1024, 1 bit) t A1416A Kathmandu (a.k.a. Color VRX) (1280x1024 @ 60 hz, 8 bits, DIO-II) .bullet) t HP-HIL devices .(bullet -compact Keyboards t Two and three button mice t 46094 Quadrature Port (supports normal serial mice) t Graphics tablets t Dial boxes t ID modules .bullet) t Miscellaneous boards/interfaces .(bullet -compact 98265A SCSI interface (DIO-I board, daughtercard for 98562, or built-in) t 98561 Human Interface board (DIO-I board with serial port, HP-HIL, and HP-IB) t 98562 System Interface board (DIO-II board with serial port, HP-HIL, HP-IB, DMA, and ethernet, has optional fast HP-IB or SCSI daughterboard) t 98620 DMA card (DIO-I board, for use with 98561) t 98624 HP-IB interface (DIO-I board or built-in) t 98625A and 98625B 'fast' HP-IB interface (DIO-I board or daughtercard for 98562) .bullet) .bullet)
Indexes created Sat Nov 08 18:09:48 GMT 2025