xref: /src/etc/defaults/rc.conf

#	$NetBSD: rc.conf,v 1.4 2001/01/03 17:54:04 itojun Exp $
#
# /etc/defaults/rc.conf --
#	default configuration of /etc/rc.conf
#
# see rc.conf(5) for more information.
#
# DO NOT EDIT THIS FILE DIRECTLY; IT MAY BE REPLACED DURING A SYSTEM UPGRADE.
# EDIT /etc/rc.conf INSTEAD.
#

#
# Use program=YES to enable program, NO to disable it. program_flags are
# passed to the program on the command line.
#

# Uncomment this if you want to use local paths in rc.
#
#export PATH=$PATH:/usr/pkg/sbin:/usr/pkg/bin:/usr/local/sbin:/usr/local/bin

# If this is set to NO, shutdown(8) will not run /etc/rc.shutdown.
#
do_rcshutdown=YES

# Basic network configuration
#

# Fully Qualified Internet Domain Name (a.k.a. hostname, e.g. foo.baz.edu).
# If blank, use /etc/myname.
#
hostname=""

# If there's only one way out of your network, set this to the hostname
# or the IP address of the router that will get your packets off the LAN.
# If blank, use /etc/mygate.
#
defaultroute=""

# The NIS domain name (formerly known as Yellow Pages); not in any way
# related to Internet domain names.
# If blank, use /etc/defaultdomain.
#
domainname=""

# Filesystems to mount early in boot-up.
# Note that `/var' is needed in $critical_filesystems_beforenet (or
# implied as part of `/') as certain services that need /var (such as
# dhclient) may be needed to get the network operational enough to mount
# the $critical_filesystems.
#
critical_filesystems_beforenet="/var"
critical_filesystems="/usr"

# Set this to YES if you have purposefully setup no swap partitions and
# don't want to be warned about it.
#
no_swap=NO

# One-time actions and programs on boot-up.
#
lkm=NO						# run /etc/rc.lkm
savecore=YES		savecore_flags="-z"
clear_tmp=YES					# clear /tmp after reboot
update_motd=YES					# updates /etc/motd
dmesg=YES		dmesg_flags=""		# write /var/run/dmesg.boot
accounting=NO					# needs /var/account/acct
newsyslog=NO		newsyslog_flags=""	# trim log files

# NOTE: default coredump name now set in /etc/sysctl.conf

# Security setting.  If $securelevel is non-empty, the system securelevel
# is set to this value early in the boot sequence.  Otherwise the default
# action is taken (see init(8)).
#
securelevel=""					# securelevel to set to

# To set the IP address of an interface either use
#  ifconfig_xxN="IP-NO"
# where xxN is the interface.  If this variable is not set then
# contents of the file /etc/ifconfig.xxN is used.

# Networking startup.
#
ipfilter=NO					# uses /etc/ipf.conf
ipnat=NO					# uses /etc/ipnat.conf
ipsec=NO					# uses /etc/ipsec.conf
ipmon=NO		ipmon_flags="-sn"	# syslog ipfilter messages
auto_ifconfig=YES				# config all avail. interfaces
net_interfaces=""				# used only if above is NO
flushroutes=YES					# flush routes in netstart
dhclient=NO					# behave as a DHCP client
dhclient_flags=""				# blank: config all interfaces
ntpdate=NO  		ntpdate_flags="-b -s"	# May need '-u' thru firewall
ppp_peers=""					# /etc/ppp/peers to call
ip6mode=host					# host, autohost or router
ip6sitelocal=NO					# IPv6 sitelocal addrs
rtsol=NO		rtsol_flags=""		# for ip6mode=autohost only

# Daemons required by servers.  These are not needed for strictly client use.
#

# inetd is used to start the IP-based services enabled in /etc/inetd.conf
#
inetd=YES		inetd_flags="-l"	# -l logs libwrap

# rpcbind (formerly known as 'portmap') is used to look up RPC-based services.
#
rpcbind=NO		rpcbind_flags="-l"	# -l logs libwrap

# Commonly used daemons.
#
syslogd=YES		syslogd_flags="-s"	# -s "secure" unix domain only
cron=YES
named=NO		named_flags=""
timed=NO		timed_flags=""
ntpd=NO			ntpd_flags=""
sendmail=NO		sendmail_flags="-bd -q30m"
postfix=NO
lpd=NO			lpd_flags="-s"		# -s "secure" unix domain only
sshd=NO			sshd_flags=""

# Routing daemons.
#
routed=NO		routed_flags="-q"
gated=NO		gated_flags=""
mrouted=NO		mrouted_flags=""
route6d=NO		route6d_flags=""
rtsold=NO		rtsold_flags=""		# for ip6mode=autohost only

# Daemons used to boot other hosts over a network.
#
rarpd=NO		rarpd_flags="-a"
bootparamd=NO		bootparamd_flags=""
dhcpd=NO		dhcpd_flags="-q"
dhcrelay=NO		dhcrelay_flags=""
rbootd=NO		rbootd_flags=""
mopd=NO			mopd_flags="-a"
rtadvd=NO		rtadvd_flags=""

# X11 daemons.
#
xfs=NO			xfs_flags=""		# X11 font server
xdm=NO			xdm_flags=""		# X11 display manager; needs
						# wscons=YES for local displays.

# YP (NIS) daemons.
#
ypbind=NO		ypbind_flags=""
ypserv=NO		ypserv_flags="-d"
yppasswdd=NO		yppasswdd_flags=""

# NFS daemons and parameters.
#
nfs_client=NO					# enable client daemons
nfs_server=NO					# enable server daemons
			mountd_flags=""
			nfsd_flags="-6tun 4"
lockd=NO		lockd_flags=""
statd=NO		statd_flags=""
amd=NO			amd_flags="-l syslog -x error,noinfo,nostats"
			amd_dir=/amd			# mount dir

# Heimdal Kerberos 5 KDC (with Kerberos IV compatibility)
kdc=NO			kdc_flags=""

# Other daemons.
#
rwhod=NO

# Hardware daemons.
#
apmd=NO			apmd_flags=""		# APM power management daemon.
screenblank=NO		screenblank_flags=""	# wscons and FBIO screenblanker

# Configuration of "wscons" console driver virtual screens.
#
wscons=NO		wscons_flags=""		# setup wscons from wscons.conf