rc.conf revision 1.93
1 # $NetBSD: rc.conf,v 1.93 2008/05/29 15:38:35 joerg Exp $ 2 # 3 # /etc/defaults/rc.conf -- 4 # default configuration of /etc/rc.conf 5 # 6 # see rc.conf(5) for more information. 7 # 8 # DO NOT EDIT THIS FILE DIRECTLY; IT MAY BE REPLACED DURING A SYSTEM UPGRADE. 9 # EDIT /etc/rc.conf INSTEAD. 10 # 11 12 # 13 # Use program=YES to enable program, NO to disable it. program_flags are 14 # passed to the program on the command line. 15 # 16 17 # Uncomment this if you want to use local paths in rc. 18 # 19 #export PATH=$PATH:/usr/pkg/sbin:/usr/pkg/bin:/usr/local/sbin:/usr/local/bin 20 21 # Uncomment the following to execute each /etc/rc.d script in 22 # the current shell rather than in a subshell. This may be 23 # faster on very slow machines that have an expensive fork(2). 24 # NOTE: USE THIS AT YOUR OWN RISK; A ROGUE COMMAND 25 # MAY INADVERTENTLY PREVENT BOOT TO MULTIUSER. 26 # 27 #rc_fast_and_loose=YES 28 29 # Additional flags to the rcorder(8) that's run by /etc/rc. 30 # 31 rc_rcorder_flags="" 32 33 # If this is set to NO, shutdown(8) will not run /etc/rc.shutdown. 34 # 35 do_rcshutdown=YES 36 37 # Additional flags to the rcorder(8) that's run by /etc/rc.shutdown. 38 # 39 rcshutdown_rcorder_flags="" 40 41 # If this is non-blank, use as the number of seconds to run a watchdog 42 # timer which will terminate /etc/rc.shutdown if the timeout expires. 43 # 44 rcshutdown_timeout="" 45 46 47 # Basic network configuration 48 # 49 50 # Fully Qualified Internet Domain Name (a.k.a. hostname, e.g. foo.baz.edu). 51 # If blank, use /etc/myname. 52 # 53 hostname="" 54 55 # If there's only one way out of your IPv4 network, set this to the hostname 56 # or the IPv4 address of the router that will get your packets off the LAN. 57 # If blank, use /etc/mygate. 58 # 59 defaultroute="" 60 61 # Same thing for IPv6. If blank, use /etc/mygate6. 62 # 63 defaultroute6="" 64 65 # The NIS domain name (formerly known as Yellow Pages); not in any way 66 # related to Internet domain names. 67 # If blank, use /etc/defaultdomain. 68 # 69 domainname="" 70 71 # Filesystems to mount early in boot-up. 72 # Note that `/var' is needed in $critical_filesystems_local (or 73 # implied as part of `/') as certain services that need /var (such as 74 # dhclient) may be needed to get the network operational enough to mount 75 # the $critical_filesystems_remote. 76 # 77 critical_filesystems_local="/var" 78 critical_filesystems_remote="/usr" 79 80 # Swap device controls. 81 # 82 no_swap=NO # Set to YES if you have purposefully setup no swap 83 # partitions and don't want to be warned about it. 84 swapoff=YES # Remove block-type swap partitions upon shutdown 85 # This defaults to yes, so that raids shutdown cleanly 86 87 # Concatenated disk driver. 88 # 89 ccd=YES 90 91 # RAIDframe driver (manually configured devices). 92 # 93 raidframe=YES 94 95 # Crypto file system. 96 # 97 cgd=YES 98 99 # One-time actions and programs on boot-up. 100 # 101 lkm=NO # Run /etc/rc.lkm. /usr needs to be part of /, or 102 # part of critical_filesystems_local. 103 104 savecore=YES savecore_flags="-z" 105 savecore_dir="/var/crash" 106 per_user_tmp=NO # per-user /tmp directories 107 per_user_tmp_dir="/private/tmp" # real storage for /tmp 108 clear_tmp=YES # clear /tmp after reboot 109 update_motd=YES # updates /etc/motd 110 dmesg=YES dmesg_flags="" # write /var/run/dmesg.boot 111 accounting=NO # uses /var/account/acct 112 newsyslog=NO newsyslog_flags="" # trim log files 113 quota=YES # check and enable quotas 114 ldconfig=YES # rebuild a.out ldconfig cache 115 sysdb=YES # build system databases 116 117 # cope with other OSes using the real time clock at localtime on this 118 # machine (by adjusting kern.rtc_offset at boot) 119 rtclocaltime=NO 120 121 # NOTE: default coredump name now set in /etc/sysctl.conf 122 123 # 124 # File system check flags; default to preen mode, checking filesystems 125 # that are listed in /etc/fstab in parallel as the fsck pass number 126 # permits. Fix minor faults automatically, and exit with non 0 only 127 # when major errors occur. 128 # 129 fsck_flags=-p 130 131 # Security setting. If $securelevel is non-empty, the system securelevel 132 # is set to this value early in the boot sequence. Otherwise the default 133 # action is taken (see init(8)). 134 # 135 securelevel="" # securelevel to set to 136 137 # To set the IP address of an interface either use 138 # ifconfig_xxN="IP-NO" 139 # where xxN is the interface. If this variable is not set then 140 # contents of the file /etc/ifconfig.xxN is used. 141 142 # Networking startup. 143 # 144 ipfilter=NO # uses /etc/ipf.conf 145 ipnat=NO # uses /etc/ipnat.conf 146 ipfs=NO ipfs_flags="" # save/load ipnat and ipf states 147 ipsec=NO # uses /etc/ipsec.conf 148 ipmon=NO ipmon_flags="-Dns" # syslog ipfilter messages 149 pf=NO pf_rules="/etc/pf.conf" 150 pflogd=NO 151 racoon=NO # IKE daemon 152 auto_ifconfig=YES # config all avail. interfaces 153 net_interfaces="" # used only if above is NO 154 flushroutes=YES # flush routes in netstart 155 dhcpcd_flags="" # For ifconfig_XXX=dhcp. 156 dhclient=NO # behave as a DHCP client 157 dhclient_flags="" # blank: config all interfaces 158 ntpdate=NO ntpdate_flags="-b -s" # May need '-u' thru firewall 159 ppp_peers="" # /etc/ppp/peers to call 160 ip6mode=host # host, autohost or router 161 ip6uniquelocal=NO # IPv6 unique-local forwarding 162 rtsol=NO rtsol_flags="-a" # for ip6mode=autohost only 163 164 # Special treatment for interfaces that need to be downed on 165 # shutdown (because they might cause unnecessary costs or block resources 166 # on the peer). All pppoe* interfaces are automatically included in this 167 # list, add others here manually. 168 #force_down_interfaces="" 169 170 ifwatchd=NO # execute up/down scripts for in-kernel PPPoE interfaces 171 ifwatchd_flags="-u /etc/ppp/ip-up -d /etc/ppp/ip-down pppoe0" 172 173 # ALTQ configuration/monitoring daemon 174 altqd=NO altqd_flags="" 175 176 # Daemons required by servers. These are not needed for strictly client use. 177 # 178 179 # inetd is used to start the IP-based services enabled in /etc/inetd.conf 180 # 181 inetd=YES inetd_flags="-l" # -l logs libwrap 182 183 # identd 184 # 185 identd=NO identd_flags="-b -l -u nobody" 186 187 # rpcbind (formerly known as 'portmap') is used to look up RPC-based services. 188 # 189 rpcbind=NO rpcbind_flags="-l" # -l logs libwrap 190 191 # Commonly used daemons. 192 # 193 syslogd=YES syslogd_flags="-s" # -s "secure" unix domain only 194 cron=YES 195 named=NO named_flags="" # see below for named_chrootdir 196 timed=NO timed_flags="" 197 ntpd=NO ntpd_flags="" # see below for ntpd_chrootdir 198 # The default setting for postfix here is YES, but gets re-examined by 199 # the rc.d/postfix startup script when it runs. The script sets 200 # _rc_d_postfix to "check", and then causes all rc.conf settings to 201 # be re-evaluated. If the value of $postfix after this is "check", 202 # the script then checks to see if /etc/mailer.conf selects the system 203 # postfix. If not, it does print a warning and does not start postfix 204 # to avoid conflict with a different MTA. 205 postfix=${_rc_d_postfix:-YES} 206 lpd=NO lpd_flags="-s" # -s "secure" unix domain only 207 sshd=NO sshd_flags="" 208 ssh_keygen_flags="-b 1024" # generate 1024 bit keys if host keys missing 209 ftpd=NO ftpd_flags="-ll" 210 211 # To run the named(8) DNS server as an unprivileged user under a 212 # chroot(2) cage, uncomment the following after migrating the contents 213 # of /etc/namedb to /var/chroot/named/etc/namedb 214 # 215 #named_chrootdir="/var/chroot/named" 216 217 # To run the ntpd(8) NTP server as an unprivileged user under a 218 # chroot(2) cage, uncomment the following, after ensuring that: 219 # - The kernel has "pseudo-device clockctl" compiled in 220 # - /dev/clockctl is present 221 # 222 #ntpd_chrootdir="/var/chroot/ntpd" 223 224 # Routing daemons. 225 # 226 routed=NO routed_flags="-q" 227 gated=NO 228 mrouted=NO mrouted_flags="" 229 route6d=NO route6d_flags="" 230 rtsold=NO rtsold_flags="" # for ip6mode=autohost only 231 232 # Daemons used to boot other hosts over a network. 233 # 234 rarpd=NO rarpd_flags="-a" 235 bootparamd=NO bootparamd_flags="" 236 dhcpd=NO dhcpd_flags="-q" 237 dhcrelay=NO dhcrelay_flags="" 238 rbootd=NO rbootd_flags="" 239 mopd=NO mopd_flags="-a" 240 ndbootd=NO ndbootd_flags="-s /tftpboot /tftpboot/bootyy" 241 rtadvd=NO rtadvd_flags="" 242 243 # X11 daemons. 244 # 245 xfs=NO xfs_flags="" # X11 font server 246 xdm=NO xdm_flags="" # X11 display manager; needs 247 # wscons=YES for local displays. 248 249 # YP (NIS) daemons. 250 # 251 ypbind=NO ypbind_flags="" 252 ypserv=NO ypserv_flags="-d" 253 yppasswdd=NO yppasswdd_flags="" 254 255 # NFS daemons and parameters. 256 # 257 mountd=NO mountd_flags="" # NFS mount requests daemon 258 nfs_client=NO # enable client daemons 259 nfs_server=NO # enable server daemons 260 nfsd_flags="-6tun 4" 261 lockd=NO lockd_flags="" 262 statd=NO statd_flags="" 263 amd=NO amd_flags="-l syslog -x error,noinfo,nostats" 264 amd_dir=/amd # mount dir 265 266 # Heimdal Kerberos 5 KDC (with Kerberos IV compatibility) 267 kdc=NO kdc_flags="--detach" 268 269 # iSCSI target 270 iscsi_target=NO iscsi_target_flags="" 271 272 # WPA daemons. 273 hostapd=NO hostapd_flags="-B /etc/hostapd.conf" 274 wpa_supplicant=NO wpa_supplicant_flags="-B" # -i<if> -c<file> 275 276 # ISDN daemon 277 isdnd=NO isdnd_flags="" 278 279 # Bluetooth daemons 280 btattach=NO # Bluetooth attach serial HCI 281 btconfig=NO # Bluetooth controller configuration 282 btdevctl=NO # Bluetooth device configuration 283 bthcid=NO bthcid_flags="" # Bluetooth HCI daemon 284 sdpd=NO sdpd_flags="" # Service Discovery daemon 285 286 # Other daemons. 287 # 288 rwhod=NO rwhod_flags="-u _rwhod" 289 envsys=NO # Set /etc/envsys.conf preferences 290 291 # Hardware daemons. 292 # 293 apmd=NO apmd_flags="" # APM power management daemon. 294 poffd=NO # x68k power switch monitor 295 poffd_flags="'shutdown -p now'" 296 powerd=NO powerd_flags="" # power management daemon 297 screenblank=NO screenblank_flags="" # wscons and FBIO screenblanker 298 299 moused=NO # serial mouse handler 300 moused_flags="-p /dev/tty00" 301 302 wdogctl=NO # watchdog timer control 303 # wdogctl_flags="-k devicename" 304 irdaattach=NO # attach serial lines to IrDA 305 irdaattach_flags="tty00" 306 307 # Configuration of "wscons" console driver virtual screens. 308 # 309 wscons=NO wscons_flags="" # setup wscons from wscons.conf 310 311 # Configuration of "wsmoused" console driver cut-n-paste support 312 # 313 wsmoused=NO wsmoused_flags="" 314 315 # Configuration of "tpctl" touch panel calibration utility 316 # 317 tpctl=NO tpctl_flags="" 318 319 # Mixer setting 320 # 321 mixerctl=NO mixerctl_mixers="" # "mixer0 mixer1" means saving 322 # and restoring their settings 323 324 # Vi recovery notification. Vi(1)'s -r option can recover files which were 325 # accidentally closed. See vi(1) for more details. 326 # 327 virecover=YES 328 329 # Veriexec signature loading. 330 # 331 veriexec=NO 332 veriexec_strict=0 333 veriexec_verbose=0 334 veriexec_flags="-k" 335
Indexes created Tue Oct 14 11:09:46 GMT 2025