Copyright (c) 1995, 1996
Justin T. Gibbs. All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote products
derived from this software withough specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
.Dd April 20, 1996 .Dt AHC 4 i386
.Os FreeBSD
.Dt AHC 4 .Os .Sh NAME .Nm ahc .Nd Adaptec VL/EISA/PCI SCSI host adapter driver .Sh SYNOPSIS For one or more VL/EISA cards: .Cd controller eisa0 .Cd controller ahc0 \} \{For VL cards: .Cd ahc0 at isa? port ? irq ?
p For EISA cards: .Cd ahc* at eisa? slot ?\}
p For one or more PCI cards: .Cd controller pci0 .Cd controller ahc0 \} \{For PCI cards: .Cd ahc* at pci? dev ? function ?\}
p \{For CardBus cards: .Cd ahc* at cardbus? dev ? function ?\}
p To enable tagged queueing: .Cd options AHC_TAGENABLE
p To enable SCB paging: .Cd options AHC_SCBPAGING_ENABLE
p For one or more .Tn SCSI busses: .Cd controller scbus0 at ahc0 \} \{For .Tn SCSI busses: .Cd scsibus* at ahc?\} .Sh DESCRIPTION This driver provides access to the .Tn SCSI bus connected to an .Tn Adaptec 274x, 284x, 2940, 3940, or controllers based on the .Tn AIC7770, .Tn AIC7850, .Tn AIC7860, .Tn AIC7870, or .Tn AIC7880 host adapter chips. Features include support for twin and wide busses, ultra .Tn SCSI , two active commands at a time per non-tagged queueing target, tagged queuing, and SCB paging which allows up to 255 active commands on all adapters except those using .Tn AIC7770 chips prior to revision E. Tagged queueing is enabled with the .Dq Dv AHC_TAGENABLE configuration option. SCB paging is enabled with the .Dq Dv AHC_SCBPAGING_ENABLE configuration option.
p Per target configuration performed in the .Tn SCSI-Select menu, accesible at boot in .No non- Ns Tn EISA models or through an .Tn EISA configuration utility for .Tn EISA models, is honored by this driver with the stipulation that the .Tn BIOS must be enabled for .Tn EISA adaptors. This includes synchronous/asynchronous transfers, maximum synchronous negotiation rate, disconnection, and the host adapter's SCSI ID.
p Note that I/O addresses are determined automatically by the probe routines, but care should be taken when using a 284x
q Tn VESA No local bus controller in an .Tn EISA system. Ensure that the jumpers setting the I/O area for the 284x match the .Tn EISA slot into which the card is inserted to prevent conflicts with other .Tn EISA cards. .Sh HARDWARE Supported cards include:
p l -tag -width xxxxxxxxxx -offset indent t AHA-274x .Tn Adaptec EISA SCSI adaptor t AHA-284x .Tn Adaptec VL SCSI adaptor t AHA-2940 .Tn Adaptec PCI SCSI adaptor t AHA-2940U .Tn Adaptec PCI Ultra SCSI adaptor t AHA-2940AU .Tn Adaptec PCI Ultra SCSI adaptor t AHA-2944 .Tn Adaptec PCI SCSI adaptor t AHA-2944U .Tn Adaptec PCI SCSI adaptor t AHA-3940 .Tn Adaptec PCI dual bus SCSI adaptor t AHA-3940U .Tn Adaptec PCI dual bus Ultra SCSI adaptor t Other EISA SCSI adaptors based on the .Tn Adaptec .Tn AIC-7770 t Other PCI controllers based on the .Tn AIC-7850, .Tn AIC-7855, .Tn AIC-7860, .Tn AIC-7870, or .Tn AIC-7880 .El .Sh BUGS Some .Tn Quantum drives (at least the Empire 2100 and 1080s) will not run on an .Tn AIC7870 Rev B in synchronous mode at 10MHz. Controllers with this problem have a 42 MHz clock crystal on them and run slightly above 10MHz, causing the drive much confusion. Setting a maximum synchronous negotiation rate of 8MHz in the .Tn SCSI-Select utility will allow normal function.
p .Tn SCSI residual handling is not complete on .Nx version of this driver. \} .Sh SEE ALSO .Xr intro 4 , .Xr aha 4 , .Xr ahb 4 , .Xr cd 4 , .Xr scsi 4 , .Xr sd 4 , .Xr st 4 .Sh AUTHOR The .Nm driver was written by Justin Gibbs. The .Tn AIC7xxx sequencer-code assembler was written by John Aycock. .Nx porting is done by Stefan Grefen, Charles M. Hannum, Michael Graff, Jason R. Thorpe, Pete Bentley and Noriyuki Soda. .Sh HISTORY The .Nm driver appeared in .Fx 2.1 and .Nx 1.1 .
Indexes created Sat Oct 25 01:09:55 GMT 2025