DRACO revision 1.103
1 # $NetBSD: DRACO,v 1.103 2005/08/19 05:19:49 christos Exp $ 2 # 3 # This file was automatically created. 4 # Changes will be lost when make is run in this directory. 5 # 6 # Created from: # NetBSD: GENERIC.in,v 1.41 2005/07/31 04:04:31 yamt Exp $ 7 # 8 # GENERIC machine description file 9 # 10 # This machine description file is used to generate the default NetBSD 11 # kernel. The generic kernel does not include all options, subsystems 12 # and device drivers, but should be useful for most applications. 13 # 14 # The machine description file can be customised for your specific 15 # machine to reduce the kernel size and improve its performance. 16 # 17 # For further information on compiling NetBSD kernels, see the config(8) 18 # man page. 19 # 20 # For further information on hardware support for this architecture, see 21 # the intro(4) man page. For further information about kernel options 22 # for this architecture, see the options(4) man page. For an explanation 23 # of each device driver in this file see the section 4 man page for the 24 # device. 25 26 27 include "arch/amiga/conf/std.amiga" 28 29 options INCLUDE_CONFIG_FILE # embed config file in kernel binary 30 31 #ident "GENERIC-$Revision: 1.103 $" 32 33 34 maxusers 8 35 options RTC_OFFSET=0 36 37 # 38 # mainboards to support (in addition to Amiga) 39 # 40 options DRACO 41 # 42 # processors this kernel should support 43 # 44 options M68060 # support for 060 45 options M060SP # MC68060 software support (Required for 060) 46 47 # 48 # Networking options 49 # 50 options INET # IP networking support (Required) 51 options INET6 # IPV6 52 #options IPSEC # IP security 53 #options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 54 #options IPSEC_NAT_T # IPsec NAT traversal (NAT-T) 55 #options IPSEC_DEBUG # debug for IP security 56 #options GATEWAY # Packet forwarding 57 #options DIRECTED_BROADCAST # Broadcast across subnets 58 59 #options MROUTING # Multicast routing 60 #options PIM # Protocol Independent Multicast 61 options NS # XNS 62 #options NSIP # XNS tunneling over IP 63 options ISO,TPIP # OSI 64 #options EON # OSI tunneling over IP 65 options CCITT,LLC,HDLC # X.25 66 options NETATALK # AppleTalk networking protocols 67 #options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG 68 69 options PPP_BSDCOMP # BSD-Compress compression support for PPP 70 options PPP_DEFLATE # Deflate compression support for PPP 71 options PPP_FILTER # Active filter support for PPP (requires bpf) 72 options PFIL_HOOKS # pfil(9) packet filter hooks 73 options IPFILTER_LOG # ipmon(8) log support 74 #options IPFILTER_DEFAULT_BLOCK # block all packets by default 75 76 #options ALTQ # Manipulate network interfaces' output queues 77 #options ALTQ_BLUE # Stochastic Fair Blue 78 #options ALTQ_CBQ # Class-Based Queueing 79 #options ALTQ_CDNR # Diffserv Traffic Conditioner 80 #options ALTQ_FIFOQ # First-In First-Out Queue 81 #options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 82 #options ALTQ_HFSC # Hierarchical Fair Service Curve 83 #options ALTQ_LOCALQ # Local queueing discipline 84 #options ALTQ_PRIQ # Priority Queueing 85 #options ALTQ_RED # Random Early Detection 86 #options ALTQ_RIO # RED with IN/OUT 87 #options ALTQ_WFQ # Weighted Fair Queueing 88 89 # Filesystems 90 file-system FFS # Berkeley fast file system 91 file-system EXT2FS # second extended file system (linux) 92 #file-system LFS # log-structured filesystem (experimental) 93 94 file-system MFS # Memory based filesystem 95 96 file-system NFS # Network File System client side code 97 file-system ADOSFS # AmigaDOS file system 98 file-system CD9660 # ISO 9660 + Rock Ridge filesystem 99 file-system MSDOSFS # MS-DOS filesystem 100 101 file-system KERNFS # kernel data-structure filesystem 102 103 file-system FDESC # user file descriptor filesystem 104 file-system NULLFS # loopback filesystem 105 file-system OVERLAY # overlay filesystem 106 #file-system PORTAL # Portal filesystem 107 file-system PROCFS # /proc filesystem 108 file-system UMAPFS # NULLFS + uid and gid remapping 109 file-system UNION # union filesystem 110 file-system SMBFS # experimental - CIFS; also needs nsmb (below) 111 file-system PTYFS # /dev/pts/N support 112 113 # Filesystem options 114 115 #options FFS_EI # FFS Endian Independant support 116 117 options QUOTA # User and group quotas in FFS 118 options SOFTDEP # FFS soft updates support. 119 #options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 120 options NFSSERVER # Network File System server side code 121 #options FFS_NO_SNAPSHOT # ffs snapshots 122 123 #options EXT2FS_SYSTEM_FLAGS # makes ext2fs file flags (append and 124 # immutable) behave as system flags. 125 126 # 127 # Compatibility options for various existing systems 128 # 129 130 #options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended. 131 options COMPAT_43 # compatibility with 4.3BSD interfaces 132 options COMPAT_09 # compatibility with NetBSD 0.9 133 options COMPAT_10 # compatibility with NetBSD 1.0 134 options COMPAT_12 # compatibility with NetBSD 1.2 135 options COMPAT_13 # compatibility with NetBSD 1.3 136 options COMPAT_14 # compatibility with NetBSD 1.4 137 options COMPAT_15 # compatibility with NetBSD 1.5 138 options COMPAT_16 # compatibility with NetBSD 1.6 139 options COMPAT_20 # compatibility with NetBSD 2.0 140 options COMPAT_30 # NetBSD 3.0 compatibility. 141 options COMPAT_SUNOS # Support to run Sun (m68k) executables 142 options COMPAT_SVR4 # Support to run SVR4 (m68k) executables 143 options COMPAT_NOMID # allow nonvalid machine id executables 144 #options COMPAT_LINUX # Support to run Linux/m68k executables 145 146 options EXEC_AOUT # 32-bit aout executables (NetBSD-1.5.x) 147 options COMPAT_AOUT_M68K # actually make some system calls work. 148 options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 149 150 # 151 # Support for System V IPC facilities. 152 # 153 options SYSVSHM # System V-like shared memory 154 options SYSVMSG # System V-like messages 155 options SYSVSEM # System V-like semaphores 156 #options SEMMNI=10 # number of semaphore identifiers 157 #options SEMMNS=60 # number of semaphores in system 158 #options SEMUME=10 # max number of undo entries per process 159 #options SEMMNU=30 # number of undo structures in system 160 options P1003_1B_SEMAPHORE # p1003.1b semaphore support 161 162 # 163 # Support for various kernel options 164 # 165 166 options KTRACE # system call tracing support 167 options SYSTRACE # system call vetting via systrace(1) 168 options LKM # Loadable kernel modules 169 #options INSECURE # disable kernel security levels 170 options SCSIVERBOSE # human readable SCSI error messages 171 options USERCONF # userconf(4) support 172 options NTP # NTP phase/frequency locked loop 173 #options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 174 175 # Enable experimental buffer queue strategy for better responsiveness under 176 # high disk I/O load. Use it with caution - it's not proven to be stable yet. 177 #options BUFQ_READPRIO 178 #options BUFQ_PRIOCSCAN 179 180 # 181 # Misc. debugging options 182 # 183 options DDB # Kernel debugger 184 #options DDB_HISTORY_SIZE=100 # Enable history editing in DDB 185 options DIAGNOSTIC # Extra kernel sanity checks 186 #options DEBUG # Enable misc. kernel debugging code 187 #options SYSCALL_DEBUG # debug all syscalls. 188 #options SCSIDEBUG # Add SCSI debugging statements 189 #options PANICBUTTON # Forced crash via keypress (?) 190 191 # 192 # Amiga specific options 193 # 194 #options LIMITMEM=24 # Do not use more than LIMITMEM MB of the 195 # first bank of RAM. (default: unlimited) 196 #options NKPTADD=4 # set this for 4 additional KPT pages 197 #options NKPTADDSHIFT=24 # set this for 1 additional KPT page 198 # per 16 MB (1<<24 bytes) of RAM 199 # uncomment and decrease this, or uncomment and 200 # increase NKPTADD if you get "out of PT pages" 201 # panics. 202 203 # ATTENTION: There is NO WARRANTY AT ALL that the sync will be complete 204 # before the 10 secondinterval ends, or that KBDRESET does work at all. 205 #options KBDRESET # sync on Ctrl-Amiga-Amiga 206 207 # These options improve performance with the built-in serial port 208 # on slower Amigas. Try the larger buffers first then lev6_defer. 209 #options SERIBUF_SIZE=4096 210 #options SEROBUF_SIZE=32 211 #options LEV6_DEFER # defers l6 to l4 (below serial l5) 212 213 214 options RETINACONSOLE # enable code to allow retina to be console 215 #options KFONT_8X11 # 8x11 font 216 217 # select a font for the console according to the character set and keymap 218 # you want to use 219 options KFONT_CONS_ISO8859_1 220 #options KFONT_CONS_ISO8859_2 221 222 # This is how you would tell the kernel the A2410 oscillator frequencies: 223 # The used frequencies are the defaults, and do not need option setting 224 #options ULOWELL_OSC1=36000000 225 #options ULOWELL_OSC2=66667000 226 227 # This is how you specify the blitting speed, higher values may speed up blits 228 # a littel bit. If you raise this value too much some trash may appear. 229 # the commented version is the default. 230 #options RH_MEMCLK=61000000 231 # this option enables the 64 bit sprite which does not work 232 # for quite a few people. E.g. The cursor sprite will turn to a block 233 # when moved to the top of the screen in X. 234 #options RH_64BIT_SPRITE 235 # enables fast scroll code appears to now work on 040 systems. 236 #options RETINA_SPEED_HACK 237 # enables the Hardwarecursor which does not work on some systems. 238 #options RH_HARDWARECURSOR 239 240 241 grfrh0 at zbus0 # retina III 242 243 grf2 at grfrh0 244 ite2 at grf2 # terminal emulators for grfs 245 246 msc0 at zbus0 # A2232 MSC multiport serial. 247 mfc0 at zbus0 # MultiFaceCard I/O board 248 mfcs0 at mfc0 unit 0 # MFC serial 249 mfcs1 at mfc0 unit 1 # MFC serial 250 #mfcp0 at mfc0 unit 0 # MFC parallel [not available yet] 251 #mfc1 at zbus0 # MultiFaceCard 2nd I/O board 252 #mfcs2 at mfc1 unit 0 253 #mfcs3 at mfc1 unit 1 254 #mfcp1 at mfc1 unit 0 255 256 hyper* at zbus? # zbus HyperCom3/3+/4/4+ 257 #hyper* at mainbus0 # not yet: HyperCom1 + HyperCom3 258 com* at hyper? port ? # Hypercom3/4 serial ports 259 lpt* at hyper? port ? # Hypercom3+/4+ parallel port 260 261 #options IOBZCLOCK=22118400 # default, uncomment the next line 262 #options IOBZCLOCK=24000000 # if needed. 263 264 iobl* at zbus? # zbus IOBlix 265 com* at iobl? port ? # IOBlix serial ports 266 lpt* at iobl? port ? # IOBlix parallel ports 267 268 269 # 270 # Keyboard device. Optionally can attach a wskbd. 271 # wskbd works together with a wsdisplay so enable them both if you will. 272 # Don't enable wskbd if you use ite. 273 # 274 # XXX in std.amiga: kbd0 at mainbus0 275 276 #wskbd0 at kbd0 console ? 277 278 279 280 281 #wsmouse* at ms? 282 283 # 284 # DraCo Mainboard devices (sans keyboard) 285 # 286 287 drbbc0 at mainbus0 # DraCo battery backed clock 288 drsupio0 at mainbus0 # DraCo superio chip 289 com* at drsupio? port ? # DraCo serial 290 lpt0 at drsupio? port ? # DraCo parallel 291 292 # 293 # Zorro-II, Zorro-III, DraCo Direct-Bus devices (sans graphics) 294 # 295 296 297 repulse* at zbus0 # ALiENDESiGN Repulse 298 audio* at repulse? 299 300 toccata* at zbus0 # MacroSystem GmbH Toccata 301 audio* at toccata? 302 303 # Ethernet cards: 304 le* at zbus0 # A2065, Ameristar, Ariadne 305 ne* at zbus0 # AriadneII, X-surf 306 ed* at zbus0 # Hydra, ASDG LanRover 307 es* at zbus0 # CEI A4066 EthernetPLUS 308 qn* at zbus0 # Quicknet 309 310 # Arcnet 311 bah* at zbus0 # C=/Ameristar A2060 / 560 312 313 314 drsc0 at mainbus0 # DraCo scsi 315 scsibus* at drsc0 316 317 318 # each hard drive from low target to high 319 # will configure to the next available sd unit number 320 sd* at scsibus? target ? lun ? # scsi disks 321 st* at scsibus? target ? lun ? # scsi tapes 322 cd* at scsibus? target ? lun ? # scsi cds 323 ch* at scsibus? target ? lun ? # scsi autochangers 324 ss* at scsibus? target ? lun ? # scsi scanner 325 uk* at scsibus? target ? lun ? # scsi unknown 326 327 pseudo-device loop # loopback network interface 328 pseudo-device sl 1 # SLIP network interfaces 329 pseudo-device ppp 1 # PPP network interfaces 330 pseudo-device pppoe # PPP over Ethernet (RFC 2516) 331 pseudo-device tun 1 # network tunnel line discipline 332 pseudo-device tap # virtual Ethernet 333 #pseudo-device gre 2 # generic L3 over IP tunnel 334 pseudo-device bpfilter 16 # Berkeley packet filter 335 pseudo-device ipfilter # IP Filter package 336 pseudo-device gif 4 # IPv[46] over IPv[46] tunnel (RFC1933) 337 #pseudo-device faith 1 # IPv[46] tcp relay translation i/f 338 #pseudo-device stf 1 # 6to4 IPv6 over IPv4 encapsulation 339 pseudo-device vlan # IEEE 802.1q encapsulation 340 pseudo-device bridge # simple inter-network bridging 341 #options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 342 #pseudo-device pf # PF packet filter 343 #pseudo-device pflog # PF log if 344 #pseudo-device fss 4 # file system snapshot device 345 346 pseudo-device view 4 # views (needed for grfcc) 347 pseudo-device pty # pseudo-terminals 348 pseudo-device clockctl # user control of clock subsystem 349 350 #pseudo-device wsfont # wsfont(4) dynamic font loading support 351 #pseudo-device wsmux # mouse & keyboard multiplexor 352 353 pseudo-device vnd 4 # vnode pseudo-disks 354 #options VND_COMPRESSION # compressed vnd(4) 355 pseudo-device ccd 4 # concatenated disk devices 356 #pseudo-device cgd 4 # cryptographic disk devices 357 pseudo-device raid 8 # RAIDframe disk driver 358 options RAID_AUTOCONFIG # auto-configuration of RAID components 359 # Options to enable various other RAIDframe RAID types. 360 # options RF_INCLUDE_EVENODD=1 361 # options RF_INCLUDE_RAID5_RS=1 362 # options RF_INCLUDE_PARITYLOGGING=1 363 # options RF_INCLUDE_CHAINDECLUSTER=1 364 # options RF_INCLUDE_INTERDECLUSTER=1 365 # options RF_INCLUDE_PARITY_DECLUSTERING=1 366 # options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 367 368 pseudo-device rnd # /dev/random and in-kernel generator 369 #options RND_COM # use "com" randomness as well (BROKEN) 370 371 pseudo-device ksyms # /dev/ksyms (kernel symbols) 372 pseudo-device nsmb # experimental - SMB requester 373 374 config netbsd root on ? type ? 375
Indexes created Tue Sep 30 11:09:46 GMT 2025