DRACO revision 1.136 1 # $NetBSD: DRACO,v 1.136 2011/01/14 10:03:44 phx Exp $
2 #
3 # This file was automatically created.
4 # Changes will be lost when make is run in this directory.
5 #
6 # Created from: # NetBSD: GENERIC.in,v 1.77 2011/01/14 10:01:12 phx Exp $
7 #
8 # GENERIC machine description file
9 #
10 # This machine description file is used to generate the default NetBSD
11 # kernel. The generic kernel does not include all options, subsystems
12 # and device drivers, but should be useful for most applications.
13 #
14 # The machine description file can be customised for your specific
15 # machine to reduce the kernel size and improve its performance.
16 #
17 # For further information on compiling NetBSD kernels, see the config(8)
18 # man page.
19 #
20 # For further information on hardware support for this architecture, see
21 # the intro(4) man page. For further information about kernel options
22 # for this architecture, see the options(4) man page. For an explanation
23 # of each device driver in this file see the section 4 man page for the
24 # device.
25
26
27 include "arch/amiga/conf/std.amiga"
28
29 options INCLUDE_CONFIG_FILE # embed config file in kernel binary
30
31 #ident "GENERIC-$Revision: 1.136 $"
32
33
34 maxusers 8
35 options RTC_OFFSET=0
36
37 #
38 # mainboards to support (in addition to Amiga)
39 #
40 options DRACO
41 #
42 # processors this kernel should support
43 #
44 options M68060 # support for 060
45 options M060SP # MC68060 software support (Required for 060)
46
47 #
48 # Networking options
49 #
50 options INET # IP networking support (Required)
51 options INET6 # IPV6
52 #options IPSEC # IP security
53 #options IPSEC_ESP # IP security (encryption part; define w/IPSEC)
54 #options IPSEC_NAT_T # IPsec NAT traversal (NAT-T)
55 #options IPSEC_DEBUG # debug for IP security
56 #options GATEWAY # Packet forwarding
57 #options DIRECTED_BROADCAST # Broadcast across subnets
58
59 #options MROUTING # Multicast routing
60 #options PIM # Protocol Independent Multicast
61 #options ISO,TPIP # OSI
62 #options EON # OSI tunneling over IP
63 options NETATALK # AppleTalk networking protocols
64 #options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG
65
66 options PPP_BSDCOMP # BSD-Compress compression support for PPP
67 options PPP_DEFLATE # Deflate compression support for PPP
68 options PPP_FILTER # Active filter support for PPP (requires bpf)
69 options PFIL_HOOKS # pfil(9) packet filter hooks
70 options IPFILTER_LOG # ipmon(8) log support
71 options IPFILTER_LOOKUP # ippool(8) support
72 options IPFILTER_COMPAT # Compat for IP-Filter
73 #options IPFILTER_DEFAULT_BLOCK # block all packets by default
74
75 #options ALTQ # Manipulate network interfaces' output queues
76 #options ALTQ_BLUE # Stochastic Fair Blue
77 #options ALTQ_CBQ # Class-Based Queueing
78 #options ALTQ_CDNR # Diffserv Traffic Conditioner
79 #options ALTQ_FIFOQ # First-In First-Out Queue
80 #options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box)
81 #options ALTQ_HFSC # Hierarchical Fair Service Curve
82 #options ALTQ_LOCALQ # Local queueing discipline
83 #options ALTQ_PRIQ # Priority Queueing
84 #options ALTQ_RED # Random Early Detection
85 #options ALTQ_RIO # RED with IN/OUT
86 #options ALTQ_WFQ # Weighted Fair Queueing
87
88 # Filesystems
89 file-system FFS # Berkeley fast file system
90 file-system EXT2FS # second extended file system (linux)
91 #file-system LFS # log-structured filesystem (experimental)
92
93 file-system MFS # Memory based filesystem
94
95 file-system NFS # Network File System client side code
96 file-system ADOSFS # AmigaDOS file system
97 file-system CD9660 # ISO 9660 + Rock Ridge filesystem
98 file-system MSDOSFS # MS-DOS filesystem
99
100 file-system KERNFS # kernel data-structure filesystem
101
102 file-system FDESC # user file descriptor filesystem
103 file-system NULLFS # loopback filesystem
104 file-system OVERLAY # overlay filesystem
105 file-system PROCFS # /proc filesystem
106 file-system UMAPFS # NULLFS + uid and gid remapping
107 file-system UNION # union filesystem
108 file-system SMBFS # experimental - CIFS; also needs nsmb (below)
109 file-system PTYFS # /dev/pts/N support
110 file-system TMPFS # Efficient memory file-system
111 #file-system UDF # experimental - OSTA UDF CD/DVD file-system
112
113 # Filesystem options
114
115 #options FFS_EI # FFS Endian Independant support
116 options WAPBL # File system journaling support - Experimental
117
118 options QUOTA # User and group quotas in FFS
119 #options UFS_DIRHASH # UFS Large Directory Hashing - Experimental
120 options NFSSERVER # Network File System server side code
121 #options FFS_NO_SNAPSHOT # No FFS snapshot support
122
123 #options EXT2FS_SYSTEM_FLAGS # makes ext2fs file flags (append and
124 # immutable) behave as system flags.
125
126 #
127 # Compatibility options for various existing systems
128 #
129
130 #options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended.
131 options COMPAT_43 # compatibility with 4.3BSD interfaces
132 options COMPAT_09 # compatibility with NetBSD 0.9
133 options COMPAT_10 # compatibility with NetBSD 1.0
134 options COMPAT_12 # compatibility with NetBSD 1.2
135 options COMPAT_13 # compatibility with NetBSD 1.3
136 options COMPAT_14 # compatibility with NetBSD 1.4
137 options COMPAT_15 # compatibility with NetBSD 1.5
138 options COMPAT_16 # compatibility with NetBSD 1.6
139 options COMPAT_20 # compatibility with NetBSD 2.0
140 options COMPAT_30 # NetBSD 3.0 compatibility.
141 options COMPAT_40 # NetBSD 4.0 compatibility.
142 options COMPAT_50 # NetBSD 5.0 compatibility.
143 options COMPAT_SUNOS # Support to run Sun (m68k) executables
144 options COMPAT_SVR4 # Support to run SVR4 (m68k) executables
145 options COMPAT_NOMID # allow nonvalid machine id executables
146 #options COMPAT_LINUX # Support to run Linux/m68k executables
147
148 options EXEC_AOUT # 32-bit aout executables (NetBSD-1.5.x)
149 options COMPAT_AOUT_M68K # actually make some system calls work.
150 options COMPAT_BSDPTY # /dev/[pt]ty?? ptys.
151
152 #
153 # Support for System V IPC facilities.
154 #
155 options SYSVSHM # System V-like shared memory
156 options SYSVMSG # System V-like messages
157 options SYSVSEM # System V-like semaphores
158 options P1003_1B_SEMAPHORE # p1003.1b semaphore support
159
160 #
161 # Support for various kernel options
162 #
163
164 options KTRACE # system call tracing support
165 #options INSECURE # disable kernel security levels
166 options SCSIVERBOSE # human readable SCSI error messages
167 options USERCONF # userconf(4) support
168 options NTP # NTP phase/frequency locked loop
169 #options PIPE_SOCKETPAIR # smaller, but slower pipe(2)
170
171 # Enable experimental buffer queue strategy for better responsiveness under
172 # high disk I/O load. Use it with caution - it's not proven to be stable yet.
173 #options BUFQ_READPRIO
174 #options BUFQ_PRIOCSCAN
175
176 #
177 # Misc. debugging options
178 #
179 options DDB # Kernel debugger
180 #options DDB_HISTORY_SIZE=100 # Enable history editing in DDB
181 #options DIAGNOSTIC # Extra kernel sanity checks
182 #options DEBUG # Enable misc. kernel debugging code
183 #options SYSCALL_DEBUG # debug all syscalls.
184 #options SCSIDEBUG # Add SCSI debugging statements
185 #options PANICBUTTON # Forced crash via keypress (?)
186
187 #
188 # Amiga specific options
189 #
190 #options LIMITMEM=24 # Do not use more than LIMITMEM MB of the
191 # first bank of RAM. (default: unlimited)
192 #options NKPTADD=4 # set this for 4 additional KPT pages
193 #options NKPTADDSHIFT=24 # set this for 1 additional KPT page
194 # per 16 MB (1<<24 bytes) of RAM
195 # uncomment and decrease this, or uncomment and
196 # increase NKPTADD if you get "out of PT pages"
197 # panics.
198
199 # ATTENTION: There is NO WARRANTY AT ALL that the sync will be complete
200 # before the 10 secondinterval ends, or that KBDRESET does work at all.
201 #options KBDRESET # sync on Ctrl-Amiga-Amiga
202
203 # These options improve performance with the built-in serial port
204 # on slower Amigas. Try the larger buffers first then lev6_defer.
205 #options SERIBUF_SIZE=4096
206 #options SEROBUF_SIZE=32
207 #options LEV6_DEFER # defers l6 to l4 (below serial l5)
208
209
210 options RETINACONSOLE # enable code to allow retina to be console
211 #options KFONT_8X11 # 8x11 font
212
213 # select a font for the console according to the character set and keymap
214 # you want to use
215 options KFONT_CONS_ISO8859_1
216 #options KFONT_CONS_ISO8859_2
217
218 # This is how you would tell the kernel the A2410 oscillator frequencies:
219 # The used frequencies are the defaults, and do not need option setting
220 #options ULOWELL_OSC1=36000000
221 #options ULOWELL_OSC2=66667000
222
223 # This is how you specify the blitting speed, higher values may speed up blits
224 # a littel bit. If you raise this value too much some trash may appear.
225 # the commented version is the default.
226 #options RH_MEMCLK=61000000
227 # this option enables the 64 bit sprite which does not work
228 # for quite a few people. E.g. The cursor sprite will turn to a block
229 # when moved to the top of the screen in X.
230 #options RH_64BIT_SPRITE
231 # enables fast scroll code appears to now work on 040 systems.
232 #options RETINA_SPEED_HACK
233 # enables the Hardwarecursor which does not work on some systems.
234 #options RH_HARDWARECURSOR
235
236
237 grfrh0 at zbus0 # retina III
238
239 grf2 at grfrh0
240 ite2 at grf2 # terminal emulators for grfs
241
242 msc0 at zbus0 # A2232 MSC multiport serial.
243 mfc0 at zbus0 # MultiFaceCard I/O board
244 mfcs0 at mfc0 unit 0 # MFC serial
245 mfcs1 at mfc0 unit 1 # MFC serial
246 #mfcp0 at mfc0 unit 0 # MFC parallel [not available yet]
247 #mfc1 at zbus0 # MultiFaceCard 2nd I/O board
248 #mfcs2 at mfc1 unit 0
249 #mfcs3 at mfc1 unit 1
250 #mfcp1 at mfc1 unit 0
251
252 hyper* at zbus? # zbus HyperCom3/3+/4/4+
253 #hyper* at mainbus0 # not yet: HyperCom1 + HyperCom3
254 com* at hyper? port ? # Hypercom3/4 serial ports
255 lpt* at hyper? port ? # Hypercom3+/4+ parallel port
256
257 #options IOBZCLOCK=22118400 # default, uncomment the next line
258 #options IOBZCLOCK=24000000 # if needed.
259
260 iobl* at zbus? # zbus IOBlix
261 com* at iobl? port ? # IOBlix serial ports
262 lpt* at iobl? port ? # IOBlix parallel ports
263
264
265 #
266 # Keyboard device. Optionally can attach a wskbd.
267 # wskbd works together with a wsdisplay so enable them both if you will.
268 # Don't enable wskbd if you use ite.
269 #
270 # XXX in std.amiga: kbd0 at mainbus0
271
272 #wskbd0 at kbd0 console ?
273
274
275
276
277 #wsmouse* at ms?
278
279 #
280 # DraCo Mainboard devices (sans keyboard)
281 #
282
283 drbbc0 at mainbus0 # DraCo battery backed clock
284 drsupio0 at mainbus0 # DraCo superio chip
285 com* at drsupio? port ? # DraCo serial
286 lpt0 at drsupio? port ? # DraCo parallel
287
288 #
289 # Zorro-II, Zorro-III, DraCo Direct-Bus devices (sans graphics)
290 #
291
292
293 repulse* at zbus0 # ALiENDESiGN Repulse
294 audio* at repulse?
295
296 toccata* at zbus0 # MacroSystem GmbH Toccata
297 audio* at toccata?
298
299 # Ethernet cards:
300 le* at zbus0 # A2065, Ameristar, Ariadne
301 ne* at zbus0 # AriadneII, X-surf
302 ed* at zbus0 # Hydra, ASDG LanRover
303 es* at zbus0 # CEI A4066 EthernetPLUS
304 qn* at zbus0 # Quicknet
305
306 # Arcnet
307 bah* at zbus0 # C=/Ameristar A2060 / 560
308
309
310 drsc0 at mainbus0 # DraCo scsi
311 scsibus* at drsc0
312
313
314 # each hard drive from low target to high
315 # will configure to the next available sd unit number
316 sd* at scsibus? target ? lun ? # scsi disks
317 st* at scsibus? target ? lun ? # scsi tapes
318 cd* at scsibus? target ? lun ? # scsi cds
319 ch* at scsibus? target ? lun ? # scsi autochangers
320 ss* at scsibus? target ? lun ? # scsi scanner
321 uk* at scsibus? target ? lun ? # scsi unknown
322
323 #
324 # accept filters
325 pseudo-device accf_data # "dataready" accept filter
326 pseudo-device accf_http # "httpready" accept filter
327
328 pseudo-device loop # loopback network interface
329 pseudo-device sl # SLIP network interfaces
330 pseudo-device ppp # PPP network interfaces
331 pseudo-device pppoe # PPP over Ethernet (RFC 2516)
332 pseudo-device tun # network tunnel line discipline
333 pseudo-device tap # virtual Ethernet
334 #pseudo-device gre # generic L3 over IP tunnel
335 pseudo-device bpfilter # Berkeley packet filter
336 #pseudo-device carp # Common Address Redundancy Protocol
337 pseudo-device ipfilter # IP Filter package
338 pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933)
339 #pseudo-device faith # IPv[46] tcp relay translation i/f
340 pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation
341 pseudo-device vlan # IEEE 802.1q encapsulation
342 pseudo-device bridge # simple inter-network bridging
343 #options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too
344 pseudo-device agr # IEEE 802.3ad link aggregation
345 #pseudo-device pf # PF packet filter
346 #pseudo-device pflog # PF log if
347 pseudo-device fss # file system snapshot device
348
349 pseudo-device view 4 # views (needed for grfcc)
350 pseudo-device pty # pseudo-terminals
351 pseudo-device clockctl # user control of clock subsystem
352
353 #pseudo-device wsfont # wsfont(4) dynamic font loading support
354 #pseudo-device wsmux # mouse & keyboard multiplexor
355
356 pseudo-device vnd # vnode pseudo-disks
357 #options VND_COMPRESSION # compressed vnd(4)
358 pseudo-device ccd 4 # concatenated disk devices
359 #pseudo-device cgd 4 # cryptographic disk devices
360 pseudo-device raid 8 # RAIDframe disk driver
361 options RAID_AUTOCONFIG # auto-configuration of RAID components
362 # Options to enable various other RAIDframe RAID types.
363 # options RF_INCLUDE_EVENODD=1
364 # options RF_INCLUDE_RAID5_RS=1
365 # options RF_INCLUDE_PARITYLOGGING=1
366 # options RF_INCLUDE_CHAINDECLUSTER=1
367 # options RF_INCLUDE_INTERDECLUSTER=1
368 # options RF_INCLUDE_PARITY_DECLUSTERING=1
369 # options RF_INCLUDE_PARITY_DECLUSTERING_DS=1
370
371 pseudo-device rnd # /dev/random and in-kernel generator
372 #options RND_COM # use "com" randomness as well (BROKEN)
373
374 pseudo-device ksyms # /dev/ksyms (kernel symbols)
375 pseudo-device nsmb # experimental - SMB requester
376
377 # Veriexec
378 #
379 # a pseudo device needed for veriexec
380 #pseudo-device veriexec 1
381 #
382 # Uncomment the fingerprint methods below that are desired. Note that
383 # removing fingerprint methods will have almost no impact on the kernel
384 # code size.
385 #
386 #options VERIFIED_EXEC_FP_RMD160
387 #options VERIFIED_EXEC_FP_SHA256
388 #options VERIFIED_EXEC_FP_SHA384
389 #options VERIFIED_EXEC_FP_SHA512
390 #options VERIFIED_EXEC_FP_SHA1
391 #options VERIFIED_EXEC_FP_MD5
392
393 config netbsd root on ? type ?
394