xref: /src/sys/arch/arm/sa11x0/sa11x0_reg.h

/*	$NetBSD: sa11x0_reg.h,v 1.6.64.1 2008/05/16 02:22:02 yamt Exp $	*/

/*-
 * Copyright (c) 2001 The NetBSD Foundation, Inc.  All rights reserved.
 *
 * This code is derived from software contributed to The NetBSD Foundation
 * by IWAMOTO Toshihiro.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
 * PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 */

#ifndef _ARM_SA11X0_REG_H_
#define _ARM_SA11X0_REG_H_

/* Physical register base addresses */
#define SAOST_BASE		0x90000000	/* OS Timer */
#define SARTC_BASE		0x90010000	/* Real-Time Clock */
#define SAPMR_BASE		0x90020000	/* Power Manager */
#define SARCR_BASE		0x90030000	/* Reset Controller */
#define SAGPIO_BASE		0x90040000	/* GPIO */
#define SAIPIC_BASE		0x90050000	/* Interrupt Controller */
#define SAPPC_BASE		0x90060000	/* Peripheral Pin Controller */
#define SAUDC_BASE		0x80000000	/* USB Device Controller*/
#define SACOM1_BASE		0x80010000	/* GPCLK/UART 1 */
#define SACOM2_BASE		0x80030000	/* Infrared Comm. Port (ICP) */
#define SACOM3_BASE		0x80050000	/* UART 3  */
#define SAMCP_BASE		0x80060000	/* MCP Controller */
#define SASSP_BASE		0x80070000	/* Synchronous serial port */

#define SADMAC_BASE		0xB0000000	/* DMA Controller */
#define SALCD_BASE		0xB0100000	/* LCD */

/* Register base virtual addresses mapped by initarm() */
#define SACOM3_VBASE		0xd000d000

/* Interrupt controller registers */
#define SAIPIC_NPORTS		9
#define SAIPIC_IP		0x00		/* IRQ pending register */
#define SAIPIC_MR		0x04		/* Mask register */
#define SAIPIC_LR		0x08		/* Level register */
#define SAIPIC_FP		0x10		/* FIQ pending register */
#define SAIPIC_PR		0x20		/* Pending register */
#define SAIPIC_CR		0x0C		/* Control register */

/* width of interrupt controller */
#define ICU_LEN			32

/* Reset controller registers */
#define SARCR_RSRR		0x0		/* Software reset register */
#define SARCR_RCSR		0x4		/* Reset status register */
#define SARCR_TUCR		0x8		/* Test Unit control reg */

#endif /* _ARM_SA11X0_REG_H_ */