xref: /src/sys/arch/cesfic/dev/zs.c

/*	$NetBSD: zs.c,v 1.15.4.1 2008/06/18 16:32:40 simonb Exp $	*/

/*-
 * Copyright (c) 1996 The NetBSD Foundation, Inc.
 * All rights reserved.
 *
 * This code is derived from software contributed to The NetBSD Foundation
 * by Gordon W. Ross.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
 * PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 */

/*
 * Zilog Z8530 Dual UART driver (machine-dependent part)
 *
 * Runs two serial lines per chip using slave drivers.
 * Plain tty/async lines use the zs_async slave.
 */

#include <sys/cdefs.h>
__KERNEL_RCSID(0, "$NetBSD: zs.c,v 1.15.4.1 2008/06/18 16:32:40 simonb Exp $");

#include "opt_ddb.h"

#include <sys/param.h>
#include <sys/systm.h>
#include <sys/conf.h>
#include <sys/device.h>
#include <sys/file.h>
#include <sys/ioctl.h>
#include <sys/kernel.h>
#include <sys/malloc.h>
#include <sys/proc.h>
#include <sys/tty.h>
#include <sys/time.h>
#include <sys/syslog.h>

#include <dev/cons.h>
#include <dev/ic/z8530reg.h>

#include <machine/cpu.h>

#include <machine/z8530var.h>
#include <cesfic/dev/zsvar.h>

#include "ioconf.h"

int zs_getc(void *);
void zs_putc(void*, int);

static struct zs_chanstate zs_conschan_store;
static int zs_hwflags[2][2];

static uint8_t zs_init_reg[16] = {
	0,	/* 0: CMD (reset, etc.) */
	0,	/* 1: No interrupts yet. */
	0x18 + ZSHARD_PRI,	/* IVECT */
	ZSWR3_RX_8 | ZSWR3_RX_ENABLE,
	ZSWR4_CLK_X16 | ZSWR4_ONESB | ZSWR4_EVENP,
	ZSWR5_TX_8 | ZSWR5_TX_ENABLE,
	0,	/* 6: TXSYNC/SYNCLO */
	0,	/* 7: RXSYNC/SYNCHI */
	0,	/* 8: alias for data port */
	ZSWR9_MASTER_IE,
	0,	/*10: Misc. TX/RX control bits */
	ZSWR11_TXCLK_BAUD | ZSWR11_RXCLK_BAUD,
	11,	/*12: BAUDLO (default=9600) */
	0,	/*13: BAUDHI (default=9600) */
	ZSWR14_BAUD_ENA | ZSWR14_BAUD_FROM_PCLK,
	ZSWR15_BREAK_IE | ZSWR15_DCD_IE,
};

static int zsc_print(void *, const char *);
int zscngetc(dev_t);
void zscnputc(dev_t, int);

static struct consdev zscons = {
	NULL, NULL,
	zscngetc, zscnputc, nullcnpollc, NULL, NULL, NULL,
	NODEV, 1
};

void
zs_config(struct zsc_softc *zsc, char *base)
{
	struct zsc_attach_args zsc_args;
	struct zs_chanstate *cs;
	int zsc_unit, channel, s;

	zsc_unit = device_unit(zsc->zsc_dev);
	aprint_normal(": Zilog 8530 SCC\n");

	/*
	 * Initialize software state for each channel.
	 */
	for (channel = 0; channel < 2; channel++) {
		zsc_args.channel = channel;
		zsc_args.hwflags = zs_hwflags[zsc_unit][channel];

		/*
		 * If we're the console, copy the channel state, and
		 * adjust the console channel pointer.
		 */
		if (zsc_args.hwflags & ZS_HWFLAG_CONSOLE) {
			cs = &zs_conschan_store;
		} else {
			cs = malloc(sizeof(struct zs_chanstate),
				    M_DEVBUF, M_NOWAIT | M_ZERO);
			if(channel==0){
				cs->cs_reg_csr  = base + 7;
				cs->cs_reg_data = base + 15;
			} else {
				cs->cs_reg_csr  = base + 3;
				cs->cs_reg_data = base + 11;
			}
			memcpy(cs->cs_creg, zs_init_reg, 16);
			memcpy(cs->cs_preg, zs_init_reg, 16);
			cs->cs_defspeed = 9600;
		}
		zsc->zsc_cs[channel] = cs;
		zs_lock_init(cs);

		cs->cs_defcflag = CREAD | CS8 | HUPCL;

		/* Make these correspond to cs_defcflag (-crtscts) */
		cs->cs_rr0_dcd = ZSRR0_DCD;
		cs->cs_rr0_cts = 0;
		cs->cs_wr5_dtr = ZSWR5_DTR | ZSWR5_RTS;
		cs->cs_wr5_rts = 0;

		cs->cs_channel = channel;
		cs->cs_private = NULL;
		cs->cs_ops = &zsops_null;
		cs->cs_brg_clk = 4000000 / 16;

		/*
		 * Clear the master interrupt enable.
		 * The INTENA is common to both channels,
		 * so just do it on the A channel.
		 */
		if (channel == 0) {
			zs_write_reg(cs, 9, 0);
		}

		/*
		 * Look for a child driver for this channel.
		 * The child attach will setup the hardware.
		 */
		if (!config_found(zsc->zsc_dev, (void *)&zsc_args,
		    zsc_print)) {
			/* No sub-driver.  Just reset it. */
			uint8_t reset = (channel == 0) ?
				ZSWR9_A_RESET : ZSWR9_B_RESET;
			s = splzs();
			zs_write_reg(cs,  9, reset);
			splx(s);
		}
	}
}

static int
zsc_print(void *aux, const char *name)
{
	struct zsc_attach_args *args = aux;

	if (name != NULL)
		aprint_normal("%s: ", name);

	if (args->channel != -1)
		aprint_normal(" channel %d", args->channel);

	return UNCONF;
}

int
zshard(void *arg)
{
	struct zsc_softc *zsc;
	int unit, rval;

	rval = 0;
	for (unit = 0; unit < zsc_cd.cd_ndevs; unit++) {
		zsc = device_lookup_private(&zsc_cd, unit);
		if (zsc == NULL)
			continue;
		rval |= zsc_intr_hard(zsc);
		if ((zsc->zsc_cs[0]->cs_softreq) ||
		    (zsc->zsc_cs[1]->cs_softreq)) {
			softint_schedule(zsc->zsc_softintr_cookie);
		}
	}
	return (rval);
}

uint8_t
zs_read_reg(struct zs_chanstate *cs, uint8_t reg)
{
	uint8_t val;

	*cs->cs_reg_csr = reg;
	ZS_DELAY();
	val = *cs->cs_reg_csr;
	ZS_DELAY();
	return val;
}

void
zs_write_reg(struct zs_chanstate *cs, uint8_t reg, uint8_t val)
{
	*cs->cs_reg_csr = reg;
	ZS_DELAY();
	*cs->cs_reg_csr = val;
	ZS_DELAY();
}

uint8_t
zs_read_csr(struct zs_chanstate *cs)
{
	uint8_t val;

	val = *cs->cs_reg_csr;
	ZS_DELAY();
	return val;
}

void
zs_write_csr(struct zs_chanstate *cs, uint8_t val)
{

	*cs->cs_reg_csr = val;
	ZS_DELAY();
}

uint8_t
zs_read_data(struct zs_chanstate *cs)
{
	uint8_t val;

	val = *cs->cs_reg_data;
	ZS_DELAY();
	return val;
}

void
zs_write_data(struct zs_chanstate *cs, uint8_t val)
{

	*cs->cs_reg_data = val;
	ZS_DELAY();
}

int
zs_set_speed(struct zs_chanstate *cs, int bps)
{
	int tconst, real_bps;

	tconst = BPS_TO_TCONST(cs->cs_brg_clk, bps);

	if (tconst < 0)
		return (EINVAL);

	/* Convert back to make sure we can do it. */
	real_bps = TCONST_TO_BPS(cs->cs_brg_clk, tconst);
#if 0
	/* XXX - Allow some tolerance here? */
	if (real_bps != bps)
		return (EINVAL);
#endif
	cs->cs_preg[12] = tconst;
	cs->cs_preg[13] = tconst >> 8;

	return (0);
}

int
zs_set_modes(struct zs_chanstate *cs, int cflag)
{
	int s;

	/*
	 * Output hardware flow control on the chip is horrendous:
	 * if carrier detect drops, the receiver is disabled, and if
	 * CTS drops, the transmitter is stoped IN MID CHARACTER!
	 * Therefore, NEVER set the HFC bit, and instead use the
	 * status interrupt to detect CTS changes.
	 */
	s = splzs();
#if 0	/* XXX - See below. */
	if (cflag & CLOCAL) {
		cs->cs_rr0_dcd = 0;
		cs->cs_preg[15] &= ~ZSWR15_DCD_IE;
	} else {
		/* XXX - Need to notice DCD change here... */
		cs->cs_rr0_dcd = ZSRR0_DCD;
		cs->cs_preg[15] |= ZSWR15_DCD_IE;
	}
#endif	/* XXX */
	if (cflag & CRTSCTS) {
		cs->cs_wr5_dtr = ZSWR5_DTR;
		cs->cs_wr5_rts = ZSWR5_RTS;
		cs->cs_rr0_cts = ZSRR0_CTS;
		cs->cs_preg[15] |= ZSWR15_CTS_IE;
	} else {
		cs->cs_wr5_dtr = ZSWR5_DTR | ZSWR5_RTS;
		cs->cs_wr5_rts = 0;
		cs->cs_rr0_cts = 0;
		cs->cs_preg[15] &= ~ZSWR15_CTS_IE;
	}
	splx(s);

	/* Caller will stuff the pending registers. */
	return (0);
}

/*
 * Handle user request to enter kernel debugger.
 */
void
zs_abort(struct zs_chanstate *cs)
{
	int rr0;

	/* Wait for end of break to avoid PROM abort. */
	/* XXX - Limit the wait? */
	do {
		rr0 = *cs->cs_reg_csr;
		ZS_DELAY();
	} while (rr0 & ZSRR0_BREAK);
#ifdef DDB
	console_debugger();
#endif
}

/*
 * Polled input char.
 */
int
zs_getc(void *arg)
{
	struct zs_chanstate *cs = arg;
	int s, c;
	uint8_t rr0, stat;

	s = splhigh();
top:
	/* Wait for a character to arrive. */
	do {
		rr0 = *cs->cs_reg_csr;
		ZS_DELAY();
	} while ((rr0 & ZSRR0_RX_READY) == 0);

	/* Read error register. */
	stat = zs_read_reg(cs, 1) & (ZSRR1_FE | ZSRR1_DO | ZSRR1_PE);
	if (stat) {
		zs_write_csr(cs, ZSM_RESET_ERR);
		goto top;
	}

	/* Read character. */
	c = *cs->cs_reg_data;
	ZS_DELAY();
	splx(s);

	return (c);
}

/*
 * Polled output char.
 */
void
zs_putc(void *arg, int c)
{
	struct zs_chanstate *cs = arg;
	int s;
	uint8_t rr0;

	s = splhigh();
	/* Wait for transmitter to become ready. */
	do {
		rr0 = *cs->cs_reg_csr;
		ZS_DELAY();
	} while ((rr0 & ZSRR0_TX_READY) == 0);

	*cs->cs_reg_data = c;
	ZS_DELAY();
	splx(s);
}

int
zscngetc(dev_t dev)
{
	struct zs_chanstate *cs = &zs_conschan_store;
	int c;

	c = zs_getc(cs);
	return (c);
}

void
zscnputc(dev_t dev, int c)
{
	struct zs_chanstate *cs = &zs_conschan_store;

	zs_putc(cs, c);
}

/*
 * Common parts of console init.
 */
void
zs_cninit(void *base)
{
	struct zs_chanstate *cs;
	/*
	 * Pointer to channel state.  Later, the console channel
	 * state is copied into the softc, and the console channel
	 * pointer adjusted to point to the new copy.
	 */
	cs = &zs_conschan_store;
	zs_hwflags[0][0] = ZS_HWFLAG_CONSOLE;

	/* Setup temporary chanstate. */
	cs->cs_reg_csr  = (uint8_t *)base + 7;
	cs->cs_reg_data = (uint8_t *)base + 15;

	/* Initialize the pending registers. */
	bcopy(zs_init_reg, cs->cs_preg, 16);
	cs->cs_preg[5] |= (ZSWR5_DTR | ZSWR5_RTS);

	/* XXX: Preserve BAUD rate from boot loader. */
	/* XXX: Also, why reset the chip here? -gwr */
	/* cs->cs_defspeed = zs_get_speed(cs); */
	cs->cs_defspeed = 9600;	/* XXX */

	/* Clear the master interrupt enable. */
	zs_write_reg(cs, 9, 0);

	/* Reset the whole SCC chip. */
	zs_write_reg(cs, 9, ZSWR9_HARD_RESET);

	/* Copy "pending" to "current" and H/W. */
	zs_loadchannelregs(cs);

	/* Point the console at the SCC. */
	cn_tab = &zscons;
}