xref: /src/sys/arch/evbarm/conf/TS7200

#	$NetBSD: TS7200,v 1.62 2014/08/23 20:26:57 dholland Exp $
#
#	TS7200 - Kernel for Technologic Systems TS7200 ARM hardware
#
#	Note - the kernel size for this hardware has two limitations:
#
#	1) The total size of the kernel (text, data, and bss) must fit
#	   within 8MB.  This is mainly an issue for the INSTALL kernel
#	   (TS7200_INSTALL)
#	2) If you wish to install this kernel in flash, the compressed size
#	   (including the gunzip booter) must fit within 1441792 bytes.
#
#	If you add new devices to this kernel, please check these limitations.
#

include	"arch/evbarm/conf/std.tsarm"

#options 	INCLUDE_CONFIG_FILE	# embed config file in kernel binary
options		MSGBUFSIZE=65536
#options 	KSTACK_CHECK_MAGIC

# estimated number of users
maxusers	32

# Standard system options

options 	RTC_OFFSET=0	# hardware clock is this many mins. west of GMT
options 	NTP		# NTP phase/frequency locked loop

# CPU options

options 	CPU_ARM9	# Support the ARM9TDMI core

# File systems

file-system	FFS		# UFS
#file-system	LFS		# log-structured file system
file-system	MFS		# memory file system
file-system	NFS		# Network file system
#file-system 	ADOSFS		# AmigaDOS-compatible file system
file-system 	EXT2FS		# second extended file system (linux)
#file-system	CD9660		# ISO 9660 + Rock Ridge file system
file-system	MSDOSFS		# MS-DOS file system
#file-system	FDESC		# /dev/fd
#file-system    FILECORE        # Acorn filecore file system
file-system	KERNFS		# /kern
#file-system	NULLFS		# loopback file system
file-system	PROCFS		# /proc
#file-system	PUFFS		# Userspace file systems (e.g. ntfs-3g & sshfs)
#file-system	UMAPFS		# NULLFS + uid and gid remapping
#file-system	UNION		# union file system
file-system	PTYFS		# /dev/pts/N support

# File system options
#options 	QUOTA		# legacy UFS quotas
#options 	QUOTA2		# new, in-filesystem UFS quotas
#options 	FFS_EI		# FFS Endian Independent support
options 	NFSSERVER
options 	WAPBL		# File system journaling support
#options 	FFS_NO_SNAPSHOT	# No FFS snapshot support

# Networking options

#options 	GATEWAY		# packet forwarding
options 	INET		# IP + ICMP + TCP + UDP
options 	INET6		# IPV6
#options 	IPSEC		# IP security
#options 	IPSEC_DEBUG	# debug for IP security
#options 	MROUTING	# IP multicast routing
#options 	NETATALK	# AppleTalk networking
#options 	PPP_BSDCOMP	# BSD-Compress compression support for PPP
#options 	PPP_DEFLATE	# Deflate compression support for PPP
#options 	PPP_FILTER	# Active filter support for PPP (requires bpf)
#options 	TCP_DEBUG	# Record last TCP_NDEBUG packets with SO_DEBUG

options 	NFS_BOOT_BOOTP
options 	NFS_BOOT_DHCP
#options 	NFS_BOOT_BOOTPARAM

# Compatibility options

options		COMPAT_NETBSD32	# allow running arm (e.g. non-earm) binaries
#options 	COMPAT_LINUX
#options 	COMPAT_43	# 4.3BSD compatibility.
#options 	COMPAT_09	# NetBSD 0.9,
#options 	COMPAT_10	# NetBSD 1.0,
#options 	COMPAT_11	# NetBSD 1.1,
#options 	COMPAT_12	# NetBSD 1.2,
#options 	COMPAT_13	# NetBSD 1.3,
#options 	COMPAT_14	# NetBSD 1.4,
#options 	COMPAT_15	# NetBSD 1.5,
#options 	COMPAT_16	# NetBSD 1.6,
options 	COMPAT_20	# NetBSD 2.0,
options 	COMPAT_30	# NetBSD 3.0,
options 	COMPAT_40	# NetBSD 4.0,
options 	COMPAT_50	# NetBSD 5.0,
options 	COMPAT_60	# NetBSD 6.0, and
options 	COMPAT_70	# NetBSD 7.0 binary compatibility.
#options 	TCP_COMPAT_42	# 4.2BSD TCP/IP bug compat. Not recommended.

# Shared memory options

options 	SYSVMSG		# System V-like message queues
options 	SYSVSEM		# System V-like semaphores
options 	SYSVSHM		# System V-like memory sharing

# Device options

#options 	MEMORY_DISK_HOOKS	# boottime setup of ramdisk
#options 	MEMORY_DISK_ROOT_SIZE=3400	# Size in blocks
#options 	MEMORY_DISK_IS_ROOT	# use memory disk as root

# Console options.  The default console is speed is 115200 baud.
#options 	CONSPEED=9600		# Console speed

# Miscellaneous kernel options
options 	KTRACE		# system call tracing, a la ktrace(1)
options 	IRQSTATS	# manage IRQ statistics
#options 	KMEMSTATS	# kernel memory statistics
#options 	SCSIVERBOSE	# Verbose SCSI errors
#options 	PCIVERBOSE	# Verbose PCI descriptions
#options 	MIIVERBOSE	# Verbose MII autoconfuration messages
#options 	PCI_CONFIG_DUMP	# verbosely dump PCI config space
#options 	DDB_KEYCODE=0x40
#options 	USERCONF	# userconf(4) support
#options	PIPE_SOCKETPAIR	# smaller, but slower pipe(2)

# Development and Debugging options

#options 	PERFCTRS	# performance counters
options 	DIAGNOSTIC	# internal consistency checks
#options 	DEBUG
#options 	PMAP_DEBUG	# Enable pmap_debug_level code
#options 	VERBOSE_INIT_ARM # verbose bootstraping messages
options 	DDB		# in-kernel debugger
options		DDB_ONPANIC=1
options 	DDB_HISTORY_SIZE=100	# Enable history editing in DDB
#makeoptions	DEBUG="-g"	# compile full symbol table
makeoptions	COPY_SYMTAB=1

##options 	PMAP_INCLUDE_PTE_SYNC
##options 	LOCKDEBUG

config		netbsd		root on ? type ?
config		netbsd-epe0	root on epe0 type nfs
config		netbsd-wd0	root on wd0 type ffs
#config		netbsd-sd0	root on sd0 type ffs

# The main bus device
mainbus0	at root

# The boot cpu
cpu0		at mainbus?

# Cirrus Logic EP93xx System-on-chip
epsoc0		at mainbus?
# On-chip timers
epclk0		at epsoc? addr 0x80810000 size 0x90 intr 35
# On-chip serial UARTS
epcom0		at epsoc? addr 0x808c0000 size 0x1000 intr 52
epcom1		at epsoc? addr 0x808d0000 size 0x1000 intr 54
# On-chip USB 1.1
ohci*		at epsoc? addr 0x80020000 size 0x1000 intr 56
# On-chip 10/100 Ethernet
epe0		at epsoc? addr 0x80010000 size 0x10000 intr 39
# On-board TS-7200 CPLD
tspld0		at mainbus?
# PC/104 bus
isa0		at tspld?
# CompactFlash interface
wdc0		at tspld?
# TS-5620 battery-backed real-time clock
tsrtc*		at tspld?
# On-board GPIO ports.  Note that only 20 total GPIO pins are available
# across all ports
epgpio0		at epsoc? addr 0x80840000 size 0xcc intr 59
gpio*		at epgpio?
options		EPGPIO_PORT_C_MASK=0x00
options		EPGPIO_PORT_D_MASK=0x00
options		EPGPIO_PORT_E_MASK=0x00
options		EPGPIO_PORT_F_MASK=0x02
options		EPGPIO_PORT_G_MASK=0x00
options		EPGPIO_PORT_H_MASK=0x38

# HD44780 LCD on LCD header
#tslcd*		at tspld?
#wsdisplay*	at tslcd? console ?

# 4x4 Matrix Keypad on DIO header
#tskp*		at tspld?
#wskbd*	at tskp? console ? mux 1

# TS-SER[1,2,4] multiport serial PC/104 cards
com0		at isa? port 0x3f8 irq 6        # Standard PC serial ports
com1		at isa? port 0x2f8 irq 6
com2		at isa? port 0x3e8 irq 6
com3		at isa? port 0x2e8 irq 6

wdc1	at isa? port 0x1f0 irq 7 flags 0x00
wdc2	at isa? port 0x170 irq 7 flags 0x00

tscs0	at isa? port 0x300 iomem ? irq ? drq ?  # TS-ETH10 PC/104 ethernet
tscs1	at isa? port 0x310 iomem ? irq ? drq ?
tscs2	at isa? port 0x320 iomem ? irq ? drq ?
tscs3	at isa? port 0x330 iomem ? irq ? drq ?

tsdio0  at isa? port 0x100 # TS-DIO24 general-purpose I/O
tsdio1  at isa? port 0x108
tsdio2  at isa? port 0x110
tsdio3  at isa? port 0x118

# PCMCIA bus support
#pcmcia* at pcic? controller ? socket ?

#options PCIC_ISA_INTR_ALLOC_MASK=0xe0
# ISA PCMCIA controllers
#pcic0	at isa? port 0x3e0 iomem 0xd0000 iosiz 0x10000
#pcic1	at isa? port 0x3e2 iomem 0xe0000 iosiz 0x4000
#pcic2	at isa? port 0x3e4 iomem 0xe0000 iosiz 0x4000

# ATA (IDE) bus support
atabus* at ata?

# IDE drives
# Flags are used only with controllers that support DMA operations
# and mode settings (e.g. some pciide controllers)
# The lowest order four bits (rightmost digit) of the flags define the PIO
# mode to use, the next set of four bits the DMA mode and the third set the
# UltraDMA mode. For each set of four bits, the 3 lower bits define the mode
# to use, and the last bit must be 1 for this setting to be used.
# For DMA and UDMA, 0xf (1111) means 'disable'.
# 0x0fac means 'use PIO mode 4, DMA mode 2, disable UltraDMA'.
# (0xc=1100, 0xa=1010, 0xf=1111)
# 0x0000 means "use whatever the drive claims to support".
wd*	at atabus? drive ? flags 0x00ff

# ATAPI bus support
#atapibus* at atapi?

# ATAPI devices
# flags have the same meaning as for IDE drives.
# XXX No DMA on IDE devices for now
#cd*	at atapibus? drive ? flags 0x0ff0	# ATAPI CD-ROM drives
#sd*	at atapibus? drive ? flags 0x0000	# ATAPI disk drives
#st*	at atapibus? drive ? flags 0x0000	# ATAPI tape drives
#uk*	at atapibus? drive ? flags 0x0000	# ATAPI unknown

# MII/PHY support
#acphy*	at mii? phy ?			# Altima AC101 and AMD Am79c874 PHYs
#amhphy* at mii? phy ?			# AMD 79c901 Ethernet PHYs
#bmtphy* at mii? phy ?			# Broadcom BCM5201 and BCM5202 PHYs
#brgphy* at mii? phy ?			# Broadcom BCM5400-family PHYs
#dmphy*	at mii? phy ?			# Davicom DM9101 PHYs
#exphy*	at mii? phy ?			# 3Com internal PHYs
#gentbi* at mii? phy ?			# Generic Ten-Bit 1000BASE-[CLS]X PHYs
#glxtphy* at mii? phy ?			# Level One LXT-1000 PHYs
#gphyter* at mii? phy ?			# NS83861 Gig-E PHY
#icsphy* at mii? phy ?			# Integrated Circuit Systems ICS189x
#igphy*	at mii? phy ?			# Intel IGP01E1000
#inphy*	at mii? phy ?			# Intel 82555 PHYs
#iophy*	at mii? phy ?			# Intel 82553 PHYs
#lxtphy* at mii? phy ?			# Level One LXT-970 PHYs
#makphy* at mii? phy ?			# Marvell Semiconductor 88E1000 PHYs
#nsphy*	at mii? phy ?			# NS83840 PHYs
#nsphyter* at mii? phy ? 		# NS83843 PHYs
#pnaphy* at mii? phy ?			# generic HomePNA PHYs
#qsphy*	at mii? phy ?			# Quality Semiconductor QS6612 PHYs
#sqphy*	at mii? phy ?			# Seeq 80220/80221/80223 PHYs
#tlphy*	at mii? phy ?			# ThunderLAN PHYs
#tqphy*	at mii? phy ?			# TDK Semiconductor PHYs
ukphy*	at mii? phy ?			# generic unknown PHYs
#urlphy* at mii? phy ?			# Realtek RTL8150L internal PHYs

# USB Controller and Devices

# USB bus support
#usb*	at ehci?
usb*	at ohci?
#usb*	at uhci?
#usb*	at slhci?

# USB Hubs
uhub*	at usb?
uhub*	at uhub? port ?

# USB HID device
#uhidev*	at uhub? port ? configuration ? interface ?

# USB Mice
# ums*	at uhidev? reportid ?
# wsmouse* at ums? mux 0

# USB eGalax touch-panel
# uep*	at uhub? port ?
# wsmouse* at uep? mux 0

# USB Keyboards
#ukbd*	at uhidev? reportid ?
#wskbd*	at ukbd? console ? mux 1

# USB serial adapter
#ucycom*	at uhidev? reportid ?

# USB Generic HID devices
#uhid*	at uhidev? reportid ?

# USB Printer
#ulpt*	at uhub? port ? configuration ? interface ?

# USB Modem
#umodem*	at uhub? port ? configuration ?
#ucom*	at umodem?

# Option N.V. Wireless WAN modems
#uhso*	at uhub? port ? configuration ?

# USB Mass Storage
#umass*	at uhub? port ? configuration ? interface ?
#scsibus* at umass?
# SCSI devices
#sd*     at scsibus? target ? lun ?      # SCSI disk drives
#st*     at scsibus? target ? lun ?      # SCSI tape drives
#cd*     at scsibus? target ? lun ?      # SCSI CD-ROM drives
#ch*     at scsibus? target ? lun ?      # SCSI autochangers
#ses*    at scsibus? target ? lun ?      # SCSI Enclosure Services devices
#ss*     at scsibus? target ? lun ?      # SCSI scanners
#uk*     at scsibus? target ? lun ?      # SCSI unknown

# wd*	at umass?

# USB audio
#uaudio*	at uhub? port ? configuration ?

# USB MIDI
#umidi* at uhub? port ? configuration ?

# USB IrDA
# USB-IrDA bridge spec
#uirda* at uhub? port ? configuration ? interface ?
#irframe* at uirda?

# SigmaTel STIr4200 USB/IrDA Bridge
#ustir* at uhub? port ?
#irframe* at ustir?

# USB Ethernet adapters
#aue*	at uhub? port ?		# ADMtek AN986 Pegasus based adapters
#axe*	at uhub? port ?		# ASIX AX88172 based adapters
#cue*	at uhub? port ?		# CATC USB-EL1201A based adapters
#kue*	at uhub? port ?		# Kawasaki LSI KL5KUSB101B based adapters
#udav*	at uhub? port ?		# Davicom DM9601 based adapters
#url*	at uhub? port ?		# Realtek RTL8150L based adapters

# Prolific PL2301/PL2302 host-to-host adapter
#upl*	at uhub? port ?

# Serial adapters
#ubsa*	at uhub? port ?		# Belkin serial adapter
#ucom*	at ubsa? portno ?

#uftdi*	at uhub? port ?		# FTDI FT8U100AX serial adapter
#ucom*	at uftdi? portno ?

#umct*	at uhub? port ?		# MCT USB-RS232 serial adapter
#ucom*	at umct? portno ?

#uplcom* at uhub? port ? 	# I/O DATA USB-RSAQ2 serial adapter
#ucom*	at uplcom? portno ?

#uvscom* at uhub? port ? 	# SUNTAC Slipper U VS-10U serial adapter
#ucom*	at uvscom? portno ?
#atu*	at uhub? port ?		# Atmel AT76C50XX 802.11b adapter

# Diamond Multimedia Rio 500
# urio*	at uhub? port ?

# USB Handspring Visor
# uvisor*	at uhub? port ?
# ucom*	at uvisor?

# Kyocera AIR-EDGE PHONE
#ukyopon* at uhub? port ?
#ucom*	at ukyopon? portno ?

# USB scanners
# uscanner* at uhub? port ?

# USB scanners that use SCSI emulation, e.g., HP5300
# usscanner* at uhub? port ?

# Y@P firmware loader
# uyap* at uhub? port ?

# D-Link DSB-R100 USB radio
# udsbr*	at uhub? port ?
# radio*	at udsbr?

# USB Generic driver
ugen*	at uhub? port ?

# IrDA and Consumer Ir devices

# Toshiba Oboe
# oboe* 	at pci? dev ? function ?
# irframe* at oboe?

# CardBus IEEE1394 controllers
#fwohci* at cardbus? function ?	# IEEE1394 Open Host Controller

#fw*	at fwbus?			# IP over 1394

# IEEE1394 nodes
#fwnode* at fwbus? idhi ? idlo ?
#sbpscsi* at fwnode?
#scsibus* at sbpscsi?

# Audio Devices

# OPL[23] FM synthesizers
#opl*	at cmpci? flags 1
#opl*	at eso?
#opl*	at fms?
#opl*	at sv?
#opl*	at yds?

# Audio support
#audio*	at audiobus?

# MPU 401 UARTs
#mpu*	at cmpci?
#mpu*	at eso?
#mpu*	at fms?
#mpu*	at yds?

# MIDI support
#midi*	at midibus?

# Pseudo-Devices

# disk/mass storage pseudo-devices
#pseudo-device	md			# memory disk device (ramdisk)
pseudo-device	vnd			# disk-like interface to files
#pseudo-device	fss			# file system snapshot device
#pseudo-device	putter			# for puffs and pud

# network pseudo-devices
pseudo-device	bpfilter		# Berkeley packet filter
pseudo-device	loop			# network loopback
pseudo-device	kttcp			# network loopback

# miscellaneous pseudo-devices
pseudo-device	pty			# pseudo-terminals
#options	RND_COM
pseudo-device	clockctl		# user control of clock subsystem
pseudo-device	ksyms			# /dev/ksyms

# data mover pseudo-devices
#pseudo-device	swdmover		# software dmover(9) back-end
#pseudo-device	dmoverio		# /dev/dmover dmover(9) interface

#
# wscons options
#
# builtin terminal emulations
#options 	WSEMUL_SUN		# sun terminal emulation
#options 	WSEMUL_VT100		# VT100 / VT220 emulation
# customization of console and kernel output - see dev/wscons/wsdisplayvar.h
#options 	WSDISPLAY_CUSTOM_OUTPUT	# color customization from wsconsctl(8)
#options 	WS_DEFAULT_FG=WSCOL_WHITE
#options 	WS_DEFAULT_BG=WSCOL_BLACK
#options 	WS_DEFAULT_COLATTR="(0)"
#options 	WS_DEFAULT_MONOATTR="(0)"
#options 	WS_KERNEL_FG=WSCOL_GREEN
#options 	WS_KERNEL_BG=WSCOL_BLACK
#options 	WS_KERNEL_COLATTR=""
#options 	WS_KERNEL_MONOATTR=""
# customization of console border color
#options 	WSDISPLAY_CUSTOM_BORDER	# border customization from wsconsctl(8)
#options 	WSDISPLAY_BORDER_COLOR=WSCOL_BLUE	# default color
# compatibility to other console drivers
#options 	WSDISPLAY_COMPAT_PCVT		# emulate some ioctls
#options 	WSDISPLAY_COMPAT_SYSCONS	# emulate some ioctls
#options 	WSDISPLAY_COMPAT_USL		# wsconscfg VT handling
#options 	WSDISPLAY_COMPAT_RAWKBD		# can get raw scancodes
# see dev/pckbport/wskbdmap_mfii.c for implemented layouts
#options 	PCKBD_LAYOUT="(KB_DE | KB_NODEAD)"
# allocate a number of virtual screens at autoconfiguration time
#options 	WSDISPLAY_DEFAULTSCREENS=4
# use a large software cursor that doesn't blink
#options 	PCDISPLAY_SOFTCURSOR
# modify the screen type of the console; defaults to "80x25"
#options 	VGA_CONSOLE_SCREENTYPE="\"80x24\""
# work around a hardware bug that loaded fonts don't work; found on ATI cards
#options 	VGA_CONSOLE_ATI_BROKEN_FONTSEL
# console scrolling support.
#options 	WSDISPLAY_SCROLLSUPPORT
# enable VGA raster mode capable of displaying multilingual text on console
#options 	VGA_RASTERCONSOLE

# wscons pseudo-devices
#pseudo-device	wsmux			# mouse & keyboard multiplexor
#pseudo-device	wsfont