xref: /src/sys/arch/landisk/conf/GENERIC

# $NetBSD: GENERIC,v 1.14 2008/06/01 03:34:17 uwe Exp $
#
# GENERIC machine description file
#
# This machine description file is used to generate the default NetBSD
# kernel.  The generic kernel does not include all options, subsystems
# and device drivers, but should be useful for most applications.
#
# The machine description file can be customised for your specific
# machine to reduce the kernel size and improve its performance.
#
# For further information on compiling NetBSD kernels, see the config(8)
# man page.
#
# For further information on hardware support for this architecture, see
# the intro(4) man page.  For further information about kernel options
# for this architecture, see the options(4) man page.  For an explanation
# of each device driver in this file see the section 4 man page for the
# device.

include		"arch/landisk/conf/std.landisk"

options         INCLUDE_CONFIG_FILE     # embed config file in kernel binary

#ident          "GENERIC-$Revision: 1.14 $"

maxusers	16		# estimated number of users

makeoptions	CPUFLAGS="-m4-nofpu"		# XXX: move to std.landisk?
#makeoptions     COPTS="-Os -freorder-blocks"	# -O2 is too -falign-* zealous

# CPU-related options.
options 	PCLOCK=33333333			# 33.33MHz
options 	DONT_INIT_BSC
#options 	DONT_INIT_PCIBSC

# Cache options.
options 	SH4_CACHE_DISABLE_EMODE
#options 	SH4_CACHE_DISABLE_ICACHE
#options 	SH4_CACHE_DISABLE_DCACHE
#options 	SH4_CACHE_WB_U0_P0_P3
#options 	SH4_CACHE_WB_P1

# kloader-related
#options 	KLOADER
#options 	KLOADER_KERNEL_PATH="\"/netbsd\""
#options 	KLOADER_DEBUG

# Standard system options

options 	RTC_OFFSET=0	# hardware clock is this many mins. west of GMT
#options 	HZ=64		# clock interrupt generates every 1/HZ sec
options 	NTP		# NTP phase/frequency locked loop

options 	KTRACE		# system call tracing via ktrace(1)

options 	SYSVMSG		# System V-like message queues
options 	SYSVSEM		# System V-like semaphores
options 	SYSVSHM		# System V-like memory sharing
options 	P1003_1B_SEMAPHORE	# p1003.1b semaphore support

options 	LKM		# loadable kernel modules

options 	USERCONF	# userconf(4) support
#options 	PIPE_SOCKETPAIR	# smaller, but slower pipe(2)
options 	SYSCTL_INCLUDE_DESCR	# Include sysctl descriptions in kernel

# Enable experimental buffer queue strategy for better responsiveness under
# high disk I/O load. Likely stable but not yet the default.
#options 	BUFQ_READPRIO
#options 	BUFQ_PRIOCSCAN

# Diagnostic/debugging support options
#options 	DIAGNOSTIC	# cheap kernel consistency checks
#options 	DEBUG		# expensive debugging checks/support
#options 	KMEMSTATS	# kernel memory statistics (vmstat -m)
options 	DDB		# in-kernel debugger
#options 	DDB_ONPANIC=1	# see also sysctl(8): `ddb.onpanic'
options 	DDB_HISTORY_SIZE=512	# Enable history editing in DDB
#makeoptions	DEBUG="-g -fno-omit-frame-pointer"

# Compatibility options
options 	COMPAT_16	# NetBSD 1.6,
options 	COMPAT_20	# NetBSD 2.0,
options 	COMPAT_30	# NetBSD 3.0,
options 	COMPAT_40	# NetBSD 4.0,
options 	COMPAT_43	# and 4.3BSD
#options 	TCP_COMPAT_42	# 4.2BSD TCP/IP bug compat. Not recommended.

options 	COMPAT_OSSAUDIO	# OSS (Voxware) audio driver compatibility
options		COMPAT_BSDPTY	# /dev/[pt]ty?? ptys.

# Executable format options
options 	EXEC_COFF	# COFF executables

# File systems
file-system 	FFS		# UFS
file-system 	EXT2FS		# second extended file system (linux)
file-system 	LFS		# log-structured file system
file-system 	MFS		# memory file system
file-system 	NFS		# Network File System client
file-system 	NTFS		# Windows/NT file system (experimental)
file-system 	CD9660		# ISO 9660 + Rock Ridge file system
file-system 	MSDOSFS		# MS-DOS file system
file-system 	FDESC		# /dev/fd
file-system 	KERNFS		# /kern
file-system 	NULLFS		# loopback file system
file-system 	OVERLAY		# overlay file system
file-system 	PORTAL		# portal filesystem (still experimental)
file-system 	PROCFS		# /proc
file-system 	UMAPFS		# NULLFS + uid and gid remapping
file-system 	UNION		# union file system
file-system	CODA		# Coda File System; also needs vcoda (below)
file-system	SMBFS		# experimental - CIFS; also needs nsmb (below)
file-system	PTYFS		# /dev/pts/N support
file-system	TMPFS		# Efficient memory file-system
#file-system	UDF		# experimental - OSTA UDF CD/DVD file-system

# File system options
options 	QUOTA		# UFS quotas
#options 	FFS_EI		# FFS Endian Independent support
options 	SOFTDEP		# FFS soft updates support.
#options 	UFS_DIRHASH	# UFS Large Directory Hashing - Experimental
options 	NFSSERVER	# Network File System server
#options 	FFS_NO_SNAPSHOT	# ffs snapshots
#options 	EXT2FS_SYSTEM_FLAGS # makes ext2fs file flags (append and
				# immutable) behave as system flags.

# Networking options
#options 	GATEWAY		# packet forwarding
options 	INET		# IP + ICMP + TCP + UDP
options 	INET6		# IPV6
#options 	IPSEC		# IP security
#options 	IPSEC_ESP	# IP security (encryption part; define w/IPSEC)
#options 	IPSEC_DEBUG	# debug for IP security
#options 	MROUTING	# IP multicast routing
#options 	PIM		# Protocol Independent Multicast
#options 	ISO,TPIP	# OSI
#options 	EON		# OSI tunneling over IP
#options 	NETATALK	# AppleTalk networking protocols
#options 	PPP_BSDCOMP	# BSD-Compress compression support for PPP
#options 	PPP_DEFLATE	# Deflate compression support for PPP
#options 	PPP_FILTER	# Active filter support for PPP (requires bpf)
#options 	PFIL_HOOKS	# pfil(9) packet filter hooks
#options 	IPFILTER_LOG	# ipmon(8) log support
#options 	IPFILTER_DEFAULT_BLOCK	# block all packets by default
#options 	TCP_DEBUG	# Record last TCP_NDEBUG packets with SO_DEBUG

#options 	ALTQ		# Manipulate network interfaces' output queues
#options 	ALTQ_BLUE	# Stochastic Fair Blue
#options 	ALTQ_CBQ	# Class-Based Queueing
#options 	ALTQ_CDNR	# Diffserv Traffic Conditioner
#options 	ALTQ_FIFOQ	# First-In First-Out Queue
#options 	ALTQ_FLOWVALVE	# RED/flow-valve (red-penalty-box)
#options 	ALTQ_HFSC	# Hierarchical Fair Service Curve
#options 	ALTQ_LOCALQ	# Local queueing discipline
#options 	ALTQ_PRIQ	# Priority Queueing
#options 	ALTQ_RED	# Random Early Detection
#options 	ALTQ_RIO	# RED with IN/OUT
#options 	ALTQ_WFQ	# Weighted Fair Queueing

# These options enable verbose messages for several subsystems.
# Warning, these may compile large string tables into the kernel!
options 	MIIVERBOSE	# verbose PHY autoconfig messages
options 	PCIVERBOSE	# verbose PCI device autoconfig messages
#options 	PCI_CONFIG_DUMP	# verbosely dump PCI config space
options 	SCSIVERBOSE	# human readable SCSI error messages
options 	USBVERBOSE	# verbose USB device autoconfig messages

options 	NFS_BOOT_DHCP,NFS_BOOT_BOOTPARAM


# Kernel root file system and dump configuration.
#config		netbsd	root on ? type ?
config		netbsd	root on wd0a type ffs
#config		netbsd	root on ? type nfs


#
# Device configuration
#

mainbus0 at root

cpu*	at mainbus?

# Basic Bus Support

# PCI bus support
options 	PCI_NETBSD_CONFIGURE
shpcic*	at mainbus?		# SH7751 PCIC
pci0	at shpcic? bus ?

# SH bus
shb*	at mainbus?

# ob-board I/O bus
obio0	at mainbus?

# Serial Devices

options 	SCIFCONSOLE
options 	SCIFCN_SPEED=9600
scif0	at shb?

rs5c313rtc0 at shb0			# time-of-day clock

# SCSI Controllers and Devices

# SCSI devices
sd*	at scsibus? target ? lun ?	# SCSI disk drives
st*	at scsibus? target ? lun ?	# SCSI tape drives
cd*	at scsibus? target ? lun ?	# SCSI CD-ROM drives
ch*	at scsibus? target ? lun ?	# SCSI autochangers
ses*	at scsibus? target ? lun ?	# SCSI Enclosure Services devices
ss*	at scsibus? target ? lun ?	# SCSI scanners
uk*	at scsibus? target ? lun ?	# SCSI unknown

# IDE and related devices
# PCI IDE controllers - see pciide(4) for supported hardware.
# The 0x0001 flag force the driver to use DMA, even if the driver doesn't know
# how to set up DMA modes for this chip. This may work, or may cause
# a machine hang with some controllers.
pciide* 	at pci? dev ? function ? flags 0x0000	# GENERIC pciide driver
acardide*	at pci? dev ? function ?	# Acard IDE controllers

wdc0	at obio? port 0x14000000 irq 10		# CF
#wdc1	at obio? port 0x18000000 irq 9		# iConnect

# ATA (IDE) bus support
atabus*	at ata?

# IDE drives
# Flags are used only with controllers that support DMA operations
# and mode settings (e.g. some pciide controllers)
# The lowest order four bits (rightmost digit) of the flags define the PIO
# mode to use, the next set of four bits the DMA mode and the third set the
# UltraDMA mode. For each set of four bits, the 3 lower bits define the mode
# to use, and the last bit must be 1 for this setting to be used.
# For DMA and UDMA, 0xf (1111) means 'disable'.
# 0x0fac means 'use PIO mode 4, DMA mode 2, disable UltraDMA'.
# (0xc=1100, 0xa=1010, 0xf=1111)
# 0x0000 means "use whatever the drive claims to support".
wd*	at atabus? drive ? flags 0x0000

# ATAPI bus support
atapibus* at atapi?

# ATAPI devices
# flags have the same meaning as for IDE drives.
cd*	at atapibus? drive ? flags 0x0000	# ATAPI CD-ROM drives
sd*	at atapibus? drive ? flags 0x0000	# ATAPI disk drives
uk*	at atapibus? drive ? flags 0x0000	# ATAPI unknown

# Network Interfaces

# PCI network interfaces
re*	at pci? dev ? function ?	# Realtek 8139C+/8169/8169S/8110S
rtk*	at pci? dev ? function ?	# Realtek 8129/8139

# MII/PHY support
rlphy*	at mii? phy ?			# Realtek 8139/8201L PHYs
urlphy* at mii? phy ?			# Realtek RTL8150L internal PHYs
ukphy*	at mii? phy ?			# generic unknown PHYs


# USB Controller and Devices

# PCI USB controllers
ehci*	at pci?	dev ? function ?	# Enhanced Host Controller
ohci*	at pci?	dev ? function ?	# Open Host Controller

# USB bus support
usb*	at ehci?
usb*	at ohci?

# USB Hubs
uhub*	at usb?
uhub*	at uhub? port ?

# USB HID device
uhidev*	at uhub? port ? configuration ? interface ?

# USB Mice
ums*	at uhidev? reportid ?
wsmouse* at ums? mux 0

# USB Keyboards
ukbd*	at uhidev? reportid ?
wskbd*	at ukbd? console ? mux 1

# USB serial adpater
ucycom* at uhidev? reportid ?

# USB Generic HID devices
uhid*	at uhidev? reportid ?

# USB Printer
ulpt*	at uhub? port ? configuration ? interface ?

# USB Modem
umodem*	at uhub? port ? configuration ?
ucom*	at umodem?

# USB Mass Storage
umass*	at uhub? port ? configuration ? interface ?
scsibus* at umass?
wd*	at umass?

# USB audio
uaudio*	at uhub? port ? configuration ?

# USB MIDI
umidi* at uhub? port ? configuration ?

# USB IrDA
# USB-IrDA bridge spec
uirda* at uhub? port ? configuration ? interface ?
irframe* at uirda?

# SigmaTel STIr4200 USB/IrDA Bridge
ustir* at uhub? port ?
irframe* at ustir?

# USB Ethernet adapters
aue*	at uhub? port ?		# ADMtek AN986 Pegasus based adapters
axe*	at uhub? port ?		# ASIX AX88172 based adapters
cdce*	at uhub? port ?		# CDC, Ethernet Networking Control Model
cue*	at uhub? port ?		# CATC USB-EL1201A based adapters
kue*	at uhub? port ?		# Kawasaki LSI KL5KUSB101B based adapters
udav*	at uhub? port ?		# Davicom DM9601 based adapters
ral*	at uhub? port ?		#
url*	at uhub? port ?		# Realtek RTL8150L based adapters

# USB 802.11b adapters
atu*	at uhub? port ?		# Atmel AT76C50XX based adapters

# Prolific PL2301/PL2302 host-to-host adapter
upl*	at uhub? port ?

# Serial adapters
ubsa*	at uhub? port ?		# Belkin serial adapter
ucom*	at ubsa? portno ?

uftdi*	at uhub? port ?		# FTDI FT8U100AX serial adapter
ucom*	at uftdi? portno ?

umct*	at uhub? port ?		# MCT USB-RS232 serial adapter
ucom*	at umct? portno ?

uplcom* at uhub? port ? 	# I/O DATA USB-RSAQ2 serial adapter
ucom*	at uplcom? portno ?

uvscom* at uhub? port ? 	# SUNTAC Slipper U VS-10U serial adapter
ucom*	at uvscom? portno ?

# Diamond Multimedia Rio 500
urio*	at uhub? port ?

# USB Handspring Visor
uvisor*	at uhub? port ?
ucom*	at uvisor?

# Kyocera AIR-EDGE PHONE
ukyopon* at uhub? port ?
ucom*	at ukyopon? portno ?

# USB scanners
uscanner* at uhub? port ?

# USB scanners that use SCSI emulation, e.g., HP5300
usscanner* at uhub? port ?

# Y@P firmware loader
uyap* at uhub? port ?

# D-Link DSB-R100 USB radio
udsbr*	at uhub? port ?
radio*	at udsbr?

# USB Generic driver
ugen*	at uhub? port ?


# Audio Devices

# Audio support
audio*	at audiobus?

# MIDI support
midi*	at midibus?


# Miscellaneous Devices

# Power switch
pwrsw0	at obio?

# Reset button, USL-5P misc button
btn0	at obio?

# Pull in optional local configuration
cinclude "arch/landisk/conf/GENERIC.local"


# Pseudo-Devices

# disk/mass storage pseudo-devices
pseudo-device	ccd		4	# concatenated/striped disk devices
#pseudo-device	cgd		4	# cryptographic disk devices
pseudo-device	raid		8	# RAIDframe disk driver
options 	RAID_AUTOCONFIG		# auto-configuration of RAID components
# Options to enable various other RAIDframe RAID types.
#options 	RF_INCLUDE_EVENODD=1
#options 	RF_INCLUDE_RAID5_RS=1
#options 	RF_INCLUDE_PARITYLOGGING=1
#options 	RF_INCLUDE_CHAINDECLUSTER=1
#options 	RF_INCLUDE_INTERDECLUSTER=1
#options 	RF_INCLUDE_PARITY_DECLUSTERING=1
#options 	RF_INCLUDE_PARITY_DECLUSTERING_DS=1
pseudo-device	fss		4	# file system snapshot device

pseudo-device	md		1	# memory disk device (ramdisk)
pseudo-device	vnd			# disk-like interface to files
options 	VND_COMPRESSION		# compressed vnd(4)

# network pseudo-devices
pseudo-device	bpfilter		# Berkeley packet filter
pseudo-device	ipfilter		# IP filter (firewall) and NAT
pseudo-device	loop			# network loopback
pseudo-device	ppp			# Point-to-Point Protocol
pseudo-device	pppoe			# PPP over Ethernet (RFC 2516)
pseudo-device	sl			# Serial Line IP
pseudo-device	strip			# Starmode Radio IP (Metricom)
pseudo-device	irframetty		# IrDA frame line discipline
pseudo-device	tap			# virtual Ethernet
pseudo-device	tun			# network tunneling over tty
pseudo-device	gre			# generic L3 over IP tunnel
pseudo-device	gif			# IPv[46] over IPv[46] tunnel (RFC1933)
#pseudo-device	faith			# IPv[46] tcp relay translation i/f
#pseudo-device	stf			# 6to4 IPv6 over IPv4 encapsulation
pseudo-device	vlan			# IEEE 802.1q encapsulation
pseudo-device	bridge			# simple inter-network bridging
#options 	BRIDGE_IPF		# bridge uses IP/IPv6 pfil hooks too
pseudo-device	agr			# IEEE 802.3ad link aggregation
#pseudo-device	pf			# PF packet filter
#pseudo-device	pflog			# PF log if

# miscellaneous pseudo-devices
pseudo-device	pty			# pseudo-terminals
pseudo-device	sequencer	1	# MIDI sequencer
pseudo-device	rnd			# /dev/random and in-kernel generator
pseudo-device	clockctl		# user control of clock subsystem
pseudo-device	ksyms			# /dev/ksyms

# a pseudo device needed for Coda	# also needs CODA (above)
pseudo-device	vcoda		4	# coda minicache <-> venus comm.

# a pseudo device needed for SMBFS
pseudo-device	nsmb			# experimental - SMB requester

# wscons pseudo-devices
pseudo-device	wsmux			# mouse & keyboard multiplexor
#pseudo-device	wsfont