GENERIC revision 1.93
1 # $NetBSD: GENERIC,v 1.93 2017/02/26 12:03:14 rin Exp $ 2 # 3 # machine description file for GENERIC NAS 4 # 5 # This machine description file is used to generate the default NetBSD 6 # kernel. The generic kernel does not include all options, subsystems 7 # and device drivers, but should be useful for most applications. 8 # 9 # The machine description file can be customised for your specific 10 # machine to reduce the kernel size and improve its performance. 11 # 12 # For further information on compiling NetBSD kernels, see the config(8) 13 # man page. 14 # 15 # For further information on hardware support for this architecture, see 16 # the intro(4) man page. For further information about kernel options 17 # for this architecture, see the options(4) man page. For an explanation 18 # of each device driver in this file see the section 4 man page for the 19 # device. 20 21 include "arch/sandpoint/conf/std.sandpoint" 22 23 options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25 #ident "GENERIC-$Revision: 1.93 $" 26 27 maxusers 32 28 29 #options ALTIVEC # Include AltiVec support 30 31 # Standard system options 32 #options INSECURE # disable kernel security levels 33 34 options RTC_OFFSET=0 # hardware clock is this many mins. west of GMT 35 options KTRACE 36 37 options SYSVMSG # System V message queues 38 options SYSVSEM # System V semaphores 39 options SYSVSHM # System V shared memory 40 41 #options MODULAR # module(7) support 42 #options MODULAR_DEFAULT_AUTOLOAD 43 #options USERCONF # userconf(4) support 44 45 #options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 46 options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 47 48 # Enable experimental buffer queue strategy for better responsiveness under 49 # high disk I/O load. Use it with caution - it's not proven to be stable yet. 50 #options BUFQ_READPRIO 51 #options BUFQ_PRIOCSCAN 52 53 # Diagnostic/debugging support options 54 #options DIAGNOSTIC # cheap kernel consistency checks 55 #options DEBUG # expensive debugging checks/support 56 options DDB 57 #options DDB_HISTORY_SIZE=100 # Enable history editing in DDB 58 #options TRAP_PANICWAIT 59 #options PMAPCHECK 60 #options PMAPDEBUG 61 options MSGBUFSIZE=65536 62 63 #makeoptions DEBUG="-g" 64 65 # Compatibility options 66 options COMPAT_NOMID # NetBSD 0.8, 386BSD, and BSDI 67 options COMPAT_09 # NetBSD 0.9, 68 options COMPAT_10 # NetBSD 1.0, 69 options COMPAT_11 # NetBSD 1.1, 70 options COMPAT_12 # NetBSD 1.2 (and 386BSD and BSDI), 71 options COMPAT_13 # NetBSD 1.3 (and 386BSD and BSDI), 72 options COMPAT_14 # NetBSD 1.4, 73 options COMPAT_15 # NetBSD 1.5, 74 options COMPAT_16 # NetBSD 1.6, 75 options COMPAT_20 # NetBSD 2.0, 76 options COMPAT_30 # NetBSD 3.0, 77 options COMPAT_40 # NetBSD 4.0, 78 options COMPAT_50 # NetBSD 5.0, 79 options COMPAT_60 # NetBSD 6.0, and 80 options COMPAT_70 # NetBSD 7.0 binary compatibility. 81 options COMPAT_43 # 4.3BSD, 386BSD, and BSDI 82 #options COMPAT_386BSD_MBRPART # recognize old partition ID 83 #options COMPAT_LINUX # binary compatibility with Linux 84 #options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended. 85 options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 86 87 # Wedge support 88 options DKWEDGE_AUTODISCOVER # Automatically add dk(4) instances 89 options DKWEDGE_METHOD_GPT # Supports GPT partitions as wedges 90 #options DKWEDGE_METHOD_BSDLABEL # Support disklabel entries as wedges 91 #options DKWEDGE_METHOD_MBR # Support MBR partitions as wedges 92 options DKWEDGE_METHOD_APPLE # Support Apple partitions as wedges 93 #options DKWEDGE_METHOD_RDB # Support RDB partitions as wedges 94 95 # File systems 96 file-system FFS # UFS 97 file-system EXT2FS # second extended file system (linux) 98 #file-system LFS # log-structured file system 99 file-system MFS # memory file system 100 file-system NFS # Network File System client 101 #file-system NTFS # Windows/NT file system (experimental) 102 file-system CD9660 # ISO 9660 + Rock Ridge file system 103 file-system MSDOSFS # MS-DOS file system 104 file-system FDESC # /dev/fd 105 file-system KERNFS # /kern 106 file-system NULLFS # loopback file system 107 #file-system OVERLAY # overlay file system 108 file-system PROCFS # /proc 109 #file-system UMAPFS # NULLFS + uid and gid remapping 110 #file-system UNION # union file system 111 #file-system CODA # Coda File System; also needs vcoda (below) 112 #file-system SMBFS # experimental - CIFS; also needs nsmb (below) 113 file-system PTYFS # /dev/ptm support 114 file-system TMPFS # Efficient memory file-system 115 116 # File system options 117 options QUOTA # legacy UFS quotas 118 options QUOTA2 # new, in-filesystem UFS quotas 119 #options DISKLABEL_EI # disklabel Endian Independent support 120 #options FFS_EI # FFS Endian Independent support 121 options WAPBL # File system journaling support 122 options NFSSERVER # Network File System server 123 #options FFS_NO_SNAPSHOT # No FFS snapshot support 124 options UFS_EXTATTR # Extended attribute support for UFS1 125 #options EXT2FS_SYSTEM_FLAGS # makes ext2fs file flags (append and 126 127 #options NFS_BOOT_DHCP 128 options NFS_BOOT_BOOTPARAM,NFS_BOOT_BOOTP 129 130 # Networking options 131 #options GATEWAY # packet forwarding 132 options INET # IP + ICMP + TCP + UDP 133 options INET6 # IPV6 134 #options IPSEC # IP security 135 #options IPSEC_DEBUG # debug for IP security 136 #options MROUTING # IP multicast routing 137 #options PIM # Protocol Independent Multicast 138 #options NETATALK # AppleTalk networking protocols 139 #options PPP_BSDCOMP # BSD-Compress compression support for PPP 140 #options PPP_DEFLATE # Deflate compression support for PPP 141 #options PPP_FILTER # Active filter support for PPP (requires BPF) 142 #options IPFILTER_LOG # ipmon(8) log support 143 #options IPFILTER_LOOKUP # ippool(8) support 144 #options IPFILTER_COMPAT # Compat for IP-Filter 145 #options IPFILTER_DEFAULT_BLOCK # block all packets by default 146 #options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG 147 148 #options ALTQ # Manipulate network interfaces' output queues 149 #options ALTQ_BLUE # Stochastic Fair Blue 150 #options ALTQ_CBQ # Class-Based Queueing 151 #options ALTQ_CDNR # Diffserv Traffic Conditioner 152 #options ALTQ_FIFOQ # First-In First-Out Queue 153 #options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 154 #options ALTQ_HFSC # Hierarchical Fair Service Curve 155 #options ALTQ_LOCALQ # Local queueing discipline 156 #options ALTQ_PRIQ # Priority Queueing 157 #options ALTQ_RED # Random Early Detection 158 #options ALTQ_RIO # RED with IN/OUT 159 #options ALTQ_WFQ # Weighted Fair Queueing 160 161 # These options enable verbose messages for several subsystems. 162 # Warning, these may compile large string tables into the kernel! 163 #options PCIVERBOSE # verbose PCI device autoconfig messages 164 #options MIIVERBOSE # verbose PHY autoconfig messages 165 #options PCI_CONFIG_DUMP # verbosely dump PCI config space 166 #options SCSIVERBOSE # human readable SCSI error messages 167 #options USBVERBOSE # verbose USB device autoconfig messages 168 169 # Kernel root file system and dump configuration 170 config netbsd root on ? type ? 171 172 # 173 # Device configuration 174 # 175 mainbus0 at root 176 cpu* at mainbus0 177 178 #cfi0 at mainbus0 179 #nor* at cfi? 180 #flash* at nor? 181 182 nhpow0 at mainbus0 # NH230/231 power,LED,buttons 183 184 #options PCI_NETBSD_CONFIGURE 185 pci* at mainbus0 bus ? 186 pchb* at pci? dev ? function ? # PCI host bridge 187 188 eumb* at mainbus0 189 com0 at eumb? unit 0 # console at 0x4500 190 #com1 at eumb? unit 1 191 satmgr0 at eumb? unit 1 # satmgr at 0x4600 192 ociic* at eumb? 193 iic* at ociic? 194 lmtemp* at iic? addr 0x48 # LM75 temperature sensor 195 rs5c372rtc* at iic? addr 0x32 196 s390rtc* at iic? addr 0x30 197 pcf8563rtc* at iic? addr 0x51 198 dsrtc* at iic? addr 0x68 199 strtc* at iic? addr 0x68 200 options STRTC_NO_WATCHDOG 201 options STRTC_NO_USERRAM 202 203 # PCI IDE controllers - see pciide(4) for supported hardware. 204 acardide* at pci? dev ? function ? # Acard IDE controllers 205 cmdide* at pci? dev ? function ? # CMD tech IDE controllers 206 iteide* at pci? dev ? function ? # IT Express IDE controllers 207 satalink* at pci? dev ? function ? # SiI SATALink controllers 208 viaide* at pci? dev ? function ? # VIA IDE controllers 209 210 # ATA (IDE) bus support 211 atabus* at ata? 212 213 # IDE drives 214 # Flags are used only with controllers that support DMA operations 215 # and mode settings (e.g. some pciide controllers) 216 # The lowest order four bits (rightmost digit) of the flags define the PIO 217 # mode to use, the next set of four bits the DMA mode and the third set the 218 # UltraDMA mode. For each set of four bits, the 3 lower bits define the mode 219 # to use, and the last bit must be 1 for this setting to be used. 220 # For DMA and UDMA, 0xf (1111) means 'disable'. 221 # 0x0fac means 'use PIO mode 4, DMA mode 2, disable UltraDMA'. 222 # (0xc=1100, 0xa=1010, 0xf=1111) 223 # 0x0000 means "use whatever the drive claims to support". 224 wd* at atabus? drive ? flags 0x0000 225 226 # ATAPI bus support 227 atapibus* at atapi? 228 229 # ATAPI devices 230 # flags have the same meaning as for IDE drives. 231 cd* at atapibus? drive ? flags 0x0000 # ATAPI CD-ROM drives 232 sd* at atapibus? drive ? flags 0x0000 # ATAPI disk drives 233 uk* at atapibus? drive ? flags 0x0000 # ATAPI unknown 234 235 # PCI network interfaces 236 ral* at pci? dev ? function ? # Ralink Technology RT25x0 802.11a/b/g 237 re* at pci? dev ? function ? # Realtek 8139C+/8169/8169S/8110S 238 skc* at pci? dev ? function ? # Marvell Yukon Gigabit Ethernet 239 sk* at skc? # Marvell Yukon Gigabit Ethernet 240 stge* at pci? dev ? function ? # Sundance ST1023 Gigabit 241 tlp* at pci? dev ? function ? # DEC Tulip and similar 242 wm* at pci? dev ? function ? # Intel 8254x Gigabit Ethernet 243 244 inphy* at mii? phy ? # Intel 82555 PHYs 245 nsphy* at mii? phy ? # NS83840 PHYs 246 rgephy* at mii? phy ? # Realtek 8169S/8110S internal PHYs 247 makphy* at mii? phy ? # Marvell Semiconductor 88E1000 PHYs 248 ukphy* at mii? phy ? # generic unknown PHYs 249 250 # GPIO devices 251 gpio* at gpiobus? 252 253 # USB Controller and Devices 254 ehci* at pci? dev ? function ? # Enhanced Host Controller 255 ohci* at pci? dev ? function ? # Open Host Controller 256 257 # USB bus support 258 usb* at ehci? 259 usb* at ohci? 260 261 # USB Hubs 262 uhub* at usb? 263 uhub* at uhub? port ? 264 265 # USB HID devices 266 uhidev* at uhub? port ? configuration ? interface ? # USB HID device 267 uthum* at uhidev? reportid ? # TEMPerHUM sensors 268 uhid* at uhidev? reportid ? # USB Generic HID 269 270 # USB video 271 uvideo* at uhub? # USB Video Class capture devices 272 video* at videobus? 273 274 # USB printer 275 ulpt* at uhub? port ? configuration ? interface ? 276 277 # USB Mass Storage 278 umass* at uhub? port ? configuration ? interface ? 279 wd* at umass? 280 281 # USB scanners 282 #uscanner* at uhub? port ? 283 ugen* at uhub? port ? configuration ? interface ? # USB Generic driver 284 285 # SCSI bus support 286 scsibus* at umass? 287 288 # SCSI devices 289 sd* at scsibus? target ? lun ? # SCSI disk drives 290 cd* at scsibus? target ? lun ? # SCSI CD-ROM drives 291 292 293 # 294 # Pseudo-Devices 295 # 296 #pseudo-device crypto # /dev/crypto device 297 #pseudo-device swcrypto # software crypto implementation 298 299 # disk/mass storage pseudo-devices 300 #pseudo-device ccd # concatenated/striped disk devices 301 #pseudo-device cgd # cryptographic disk devices 302 pseudo-device fss # file system snapshot device 303 #pseudo-device putter # for puffs and pud 304 305 pseudo-device raid # RAIDframe disk driver 306 options RAID_AUTOCONFIG # auto-configuration of RAID components 307 # Options to enable various other RAIDframe RAID types. 308 #options RF_INCLUDE_EVENODD=1 309 #options RF_INCLUDE_RAID5_RS=1 310 #options RF_INCLUDE_PARITYLOGGING=1 311 #options RF_INCLUDE_CHAINDECLUSTER=1 312 #options RF_INCLUDE_INTERDECLUSTER=1 313 #options RF_INCLUDE_PARITY_DECLUSTERING=1 314 #options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 315 316 pseudo-device vnd 317 #options VND_COMPRESSION # compressed vnd(4) 318 319 # network pseudo-devices 320 pseudo-device loop 321 pseudo-device bpfilter # packet filter 322 #pseudo-device carp # Common Address Redundancy Protocol 323 #pseudo-device ppp # Point-to-Point Protocol 324 #pseudo-device pppoe # PPP over Ethernet (RFC 2516) 325 #pseudo-device ipfilter 326 #pseudo-device pf # PF packet filter 327 #pseudo-device pflog # PF log if 328 #pseudo-device sl # Serial Line IP 329 #pseudo-device tun # network tunneling over tty 330 #pseudo-device tap # virtual Ethernet 331 #pseudo-device gre # generic L3 over IP tunnel 332 #pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 333 #pseudo-device faith # IPv[46] tcp relay translation i/f 334 #pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 335 #pseudo-device vlan # IEEE 802.1q encapsulation 336 #pseudo-device bridge # simple inter-network bridging 337 #options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 338 #pseudo-device agr # IEEE 802.3ad link aggregation 339 340 # 341 # accept filters 342 #pseudo-device accf_data # "dataready" accept filter 343 #pseudo-device accf_http # "httpready" accept filter 344 345 # miscellaneous pseudo-devices 346 pseudo-device pty 347 pseudo-device clockctl # user control of clock subsystem 348 pseudo-device ksyms # /dev/ksyms 349 #pseudo-device lockstat # lock profiling 350 351 # a pseudo device needed for Coda # also needs CODA (above) 352 #pseudo-device vcoda # coda minicache <-> venus comm. 353 354 # a pseudo device needed for SMBFS 355 #pseudo-device nsmb # experimental - SMB requester 356 357 # userland interface to drivers, including autoconf and properties retrieval 358 pseudo-device drvctl 359 360 # Veriexec 361 # 362 # a pseudo device needed for veriexec 363 #pseudo-device veriexec 364 # 365 # Uncomment the fingerprint methods below that are desired. Note that 366 # removing fingerprint methods will have almost no impact on the kernel 367 # code size. 368 # 369 #options VERIFIED_EXEC_FP_RMD160 370 #options VERIFIED_EXEC_FP_SHA256 371 #options VERIFIED_EXEC_FP_SHA384 372 #options VERIFIED_EXEC_FP_SHA512 373 #options VERIFIED_EXEC_FP_SHA1 374 #options VERIFIED_EXEC_FP_MD5 375 376 #options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 377 #options PAX_ASLR=0 # PaX Address Space Layout Randomization 378
Indexes created Fri Oct 03 02:09:57 GMT 2025