TADPOLE3GX revision 1.37 1 # $NetBSD: TADPOLE3GX,v 1.37 2006/03/07 18:57:40 macallan Exp $
2
3 include "arch/sparc/conf/std.sparc"
4
5 #options INCLUDE_CONFIG_FILE # embed config file in kernel binary
6
7 # all supported SPARCbooks have V8 CPUs
8 makeoptions CCPUOPTS="-mcpu=v8 -mtune=v8"
9
10 maxusers 32
11
12 ## System kernel configuration. See options(4) for more detail.
13
14
15 # Options for variants of the Sun SPARC architecure.
16 # We currently support three architecture types; at least one is required.
17 options SUN4M # sun4m - SS10, SS20, Classic, etc.
18
19 ## System options specific to the sparc machine type
20
21 # Blink the power LED on some machines to indicate the system load.
22 #options BLINK
23
24 # wsdisplay options
25 #options WSEMUL_SUN
26 options WSEMUL_VT100
27 options WSDISPLAY_COMPAT_RAWKBD # can get raw scancodes
28 options WSDISPLAY_CUSTOM_OUTPUT # wsconsctl(8)
29
30 # black on white, kernel output in green
31 options WS_DEFAULT_FG=WSCOL_BLACK
32 options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE
33 options WS_KERNEL_FG=WSCOL_GREEN
34 options WS_KERNEL_BG=WSCOL_LIGHT_WHITE
35
36 options WSDISPLAY_COMPAT_PCVT # emulate some ioctls
37 options WSDISPLAY_COMPAT_SYSCONS # emulate some ioctls
38 options WSDISPLAY_COMPAT_USL # VT handling
39
40 options WSDISPLAY_DEFAULTSCREENS=1
41
42 options SPARCBOOK_CMD # enable screen switching with lAlt-Fn
43 #options FONT_GALLANT12x22 # the console font
44 options FONT_BOLD8x16 # a somewhat smaller font
45
46 #### System options that are the same for all ports
47
48 ## Root device configuration: change the ?'s if you are going to use a
49 ## nonstandard root partition (other than where the kernel is booted from)
50 ## and/or nonstandard root type (not ffs or nfs). Normally this can be
51 ## automagically determined at boot time.
52
53 config netbsd root on ? type ?
54
55 ## System call tracing (see ktrace(1)).
56 options KTRACE
57
58 ## Collect statistics on kernel malloc's and free's. This does have a
59 ## significant performance hit on slower machines, so it is intended for
60 ## diagnostic use only.
61 #options KMEMSTATS
62
63 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2))
64 options SYSVMSG # System V message queues
65 options SYSVSEM # System V semaphores
66 options SYSVSHM # System V shared memory
67 #options SHMMAXPGS=1024 # 1024 pages is the default
68
69 ## Loadable kernel module support; still under development.
70 options LKM
71
72 options USERCONF # userconf(4) support
73 #options PIPE_SOCKETPAIR # smaller, but slower pipe(2)
74 #options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel
75
76 ## NFS boot options; tries DHCP/BOOTP then BOOTPARAM
77 options NFS_BOOT_BOOTPARAM
78 #options NFS_BOOT_BOOTP
79 options NFS_BOOT_DHCP
80
81 #### Debugging options
82
83 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at
84 ## serial console break or keyboard reset, where the PROM would normally
85 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history.
86 #options DDB # kernel dynamic debugger
87 #options DDB_HISTORY_SIZE=100 # enable history editing in DDB
88 #options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic'
89
90 ## You may also use gdb, on another computer connected to this machine over
91 ## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified;
92 ## KGDB_DEV is a dev_t encoded device number of the serial port to use.
93 ## (0xc01 = ttya, 0xc02 = ttyb.)
94 #options KGDB # support for kernel gdb
95 #options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb')
96 #options KGDB_DEVRATE=38400 # baud rate
97
98
99 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file),
100 ## such that gdb(1) can be used on a kernel coredump.
101
102 makeoptions DEBUG="-g"
103
104
105 ## Adds code to the kernel that does internal consistency checks, and will
106 ## cause the kernel to panic if corruption of internal data structures
107 ## is detected.
108 #options DIAGNOSTIC # extra kernel sanity checking
109
110 ## Enable (possibly expensive) debugging code that may also display messages
111 ## on the system console
112 #options DEBUG
113
114 ## Make SCSI error messages more verbose when explaining their meanings.
115 options SCSIVERBOSE
116
117 ## `INSECURE' turns off the kernel security level (securelevel = 0 always).
118 ## This allows writing to /dev/mem, loading kernel modules while multi-user,
119 ## and other insecurities good only for development work. Do not use this
120 ## option on a production machine.
121 options INSECURE
122
123 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a
124 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS',
125 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same
126 ## opaque file mechanism. Perl calls this "secure setuid scripts."
127
128 #options FDSCRIPTS
129 #options SETUIDSCRIPTS
130
131 ## Options for compatibility with previous releases foreign system binaries.
132 ## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up
133 ## additional user-level utilities or system configuration files. See
134 ## compat_sunos(8) and compat_svr4(8).
135
136 options COMPAT_43 # 4.3BSD system interfaces
137 options COMPAT_10 # NetBSD 1.0 binary compatibility
138 options COMPAT_11 # NetBSD 1.1 binary compatibility
139 options COMPAT_12 # NetBSD 1.2 binary compatibility
140 options COMPAT_13 # NetBSD 1.3 binary compatibility
141 options COMPAT_14 # NetBSD 1.4 binary compatibility
142 options COMPAT_16 # NetBSD 1.6 binary compatibility
143 options COMPAT_20 # NetBSD 2.0 binary compatibility
144 options COMPAT_30 # NetBSD 3.0 compatibility.
145 options COMPAT_SUNOS # SunOS 4.x binary compatibility
146 options COMPAT_SVR4 # SunOS 5.x binary compatibility
147 #options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended.
148 options COMPAT_BSDPTY # /dev/[pt]ty?? ptys.
149
150 ## File systems. You probably need at least one of FFS or NFS.
151 file-system FFS # Berkeley Fast Filesystem
152 file-system NFS # Sun NFS-compatible filesystem client
153 file-system KERNFS # kernel data-structure filesystem
154 #file-system NULLFS # NULL layered filesystem
155 file-system MFS # memory-based filesystem
156 #file-system FDESC # user file descriptor filesystem
157 #file-system UMAPFS # uid/gid remapping filesystem
158 #file-system LFS # Log-based filesystem (still experimental)
159 #file-system PORTAL # portal filesystem (still experimental)
160 file-system PROCFS # /proc
161 file-system CD9660 # ISO 9660 + Rock Ridge file system
162 #file-system UNION # union file system
163 file-system MSDOSFS # MS-DOS FAT filesystem(s).
164 file-system PTYFS # /dev/pts/N support
165
166 ## File system options.
167 options NFSSERVER # Sun NFS-compatible filesystem server
168 options QUOTA # FFS quotas
169 #options FFS_EI # FFS Endian Independent support
170 #options FFS_NO_SNAPSHOT # No FFS snapshot support
171
172 ## Network protocol support. In most environments, INET is required.
173 options INET # IP (Internet Protocol) v4
174 #options GATEWAY # packet forwarding ("router switch")
175 #options MROUTING # packet forwarding of multicast packets
176 #options PIM # Protocol Independent Multicast
177 #options DIRECTED_BROADCAST # allow broadcasts through routers
178 #options NS # Xerox NS networking
179 #options NSIP # Xerox NS tunneling over IP
180 #options ISO,TPIP # OSI networking
181 #options EON # OSI tunneling over IP
182 #options CCITT,LLC,HDLC # X.25 packet switched protocol
183 #options NETATALK # AppleTalk (over Ethernet) protocol
184 options NTP # Network Time Protocol in-kernel support
185 #options PPS_SYNC # Add serial line synchronization for NTP
186 options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs.
187 options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device
188 options PPP_BSDCOMP # Add BSD compression to ppp device
189 options PPP_DEFLATE # Add deflate (libz) compression to ppp device
190 options PPP_FILTER # Add active filters for ppp (via bpf)
191 #options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG
192
193
194 #### Main bus and CPU .. all systems.
195 mainbus0 at root
196 cpu0 at mainbus0
197
198 #### Bus types found on SPARC systems.
199
200 obio0 at mainbus0 # sun4 and sun4m
201 iommu0 at mainbus0 # sun4m
202 sbus0 at iommu0 # sun4m
203
204 ## SBus to PCMCIA bridge
205 tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx)
206 pcmcia* at tslot?
207
208 #### Standard system devices -- all required for a given architecture
209
210 ## Auxiliary system registers on sun4c and sun4m
211 auxreg0 at obio0 # sun4m
212
213 ## Additional auxiliary system registers on Sparcbook
214 auxiotwo0 at obio0 # sun4m
215
216 ## Clock control on SPARCbook - used to put the CPU to sleep when idle
217 clkctrl0 at obio0
218
219 ## Mostek clock found on 4/300, sun4c, and sun4m systems.
220 ## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems.
221 clock0 at obio0 # sun4m
222
223 ## Timer chip found on 4/300, sun4c, and sun4m systems.
224 timer0 at obio0 # sun4m
225
226 #### Serial port configuration
227
228 ## Zilog 8530 serial chips. Each has two-channels.
229 ## zs0 is ttya and ttyb. zs1 is the keyboard and mouse.
230 zs0 at obio0 # sun4m
231 zstty0 at zs0 channel 0 # ttya
232 zstty1 at zs0 channel 1 # ttyb
233
234 zs1 at obio0 # sun4m
235 zstty* at zs1 channel ? # mouse/keyboard
236
237 kbd0 at zstty?
238 ms0 at zstty?
239
240 wskbd* at kbd? console ?
241 wsmouse* at ms?
242
243 ## Tadpole 3GX/3XL have a builtin modem that emulates a NS16450.
244 com* at obio0 # sun4m (tadpole)
245
246 ## PCMCIA serial interfaces
247 com* at pcmcia?
248 pcmcom* at pcmcia?
249 com* at pcmcom?
250
251 #### Disk controllers and disks
252
253 #
254
255 ## The following flags may be set for the NCR53c94 based esp driver:
256 ## bits 0-7: disable disconnect/reselect for the corresponding target
257 ## bits 8-15: disable synchronous negotiation for target [bit-8]
258
259 ## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards.
260 ## Both `dma' and `esp' are needed in all cases.
261 ## Two kinds of additional SBus SCSI interfaces are available. One uses
262 ## "esp at sbus" like the sun4c on-board; the other uses "esp at dma".
263
264 ## sun4/300 SCSI - an NCR53c94 or equivalent behind
265 ## an LSI Logic DMA controller
266
267 dma0 at sbus0 slot ? offset ? # sun4c/sun4m
268 esp0 at dma0 flags 0x0000 # sun4m
269
270 scsibus* at esp?
271
272 ## PCMCIA SCSI controllers
273 #aic* at pcmcia?
274 #scsibus* at aic?
275
276 ## These entries find devices on all SCSI busses and assign
277 ## unit numbers dynamically.
278 sd* at scsibus? target ? lun ? # SCSI disks
279 st* at scsibus? target ? lun ? # SCSI tapes
280 cd* at scsibus? target ? lun ? # SCSI CD-ROMs
281 ch* at scsibus? target ? lun ? # SCSI changer devices
282 ss* at scsibus? target ? lun ? # SCSI scanners
283 uk* at scsibus? target ? lun ? # unknown SCSI
284
285 ## PCMCIA IDE controllers
286 wdc* at pcmcia?
287
288 atabus* at ata?
289 wd* at atabus? drive ? flags 0x0000
290
291 ## A disk-like interface to files. Can be used to create floppy, CD,
292 ## miniroot images, etc.
293
294 pseudo-device vnd
295
296 ## Memory disk device, used on boot floppies with compressed
297 ## kernel-plus-root-disk images.
298
299 #pseudo-device md 1
300
301
302 #### Network interfaces
303
304 ## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue
305 ## Three flavors of additional SBus ethernets are available. One attaches
306 ## directly like the sun4c on-board, one uses the ledma device like the
307 ## sun4m on-board, and one uses the lebuffer device.
308
309 ledma0 at sbus0 slot ? offset ? # sun4m on-board
310 le0 at ledma0 # sun4m on-board
311
312 # PCMCIA ethernet devices
313 ep* at pcmcia?
314 #mbe* at pcmcia?
315 #ne* at pcmcia?
316 #sm* at pcmcia?
317
318 wi* at pcmcia?
319
320 ## Loopback network interface; required
321 pseudo-device loop
322
323 ## PPP, the successor to SLIP. See pppd(8).
324 pseudo-device ppp
325
326 ## Network "tunnel" device, allowing protocol stacks to run in the userland.
327 ## This is used by the third-party user-mode "ppp" program, and others.
328 pseudo-device tun
329
330 ## Generic L3 over IP tunnel
331 #pseudo-device gre # generic L3 over IP tunnel
332
333 ## Berkeley Packet Filter, required to run RARPD. A generic C-language
334 ## interface that allows selective examining of incoming packets.
335 pseudo-device bpfilter
336
337 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for
338 ## one example of the use of the IP Filter.
339 pseudo-device ipfilter
340
341
342 #### Audio and video devices
343
344 ## /dev/audio support
345
346 dbri0 at sbus0 slot ? offset ? # SUNW,DBRI[s3|e]
347 audio* at audiobus?
348
349 # Tadpole 3GX/3GS (P9100 -- P Nine One Zero Zero -> pnozz)
350 pnozz0 at sbus? slot ? offset ?
351 #options PNOZZ_EMUL_CG3 # emulate a CG3 for Xsun instead of
352 # running natively
353
354 wsdisplay* at wsemuldisplaydev? console ?
355
356 #### Other device configuration
357
358 # Tadpole microcontroller
359 tctrl0 at obio0
360
361 ## Pseudo ttys, required for network logins and programs like screen.
362
363 pseudo-device pty # pseudo-ttys (for network, etc.)
364
365 ## Random device, used to implement /dev/random (a source of random noise),
366 ## and generate randomness for some kernel formulae.
367
368 pseudo-device rnd
369
370 pseudo-device clockctl # user control of clock subsystem
371 #pseudo-device fss 4 # file system snapshot device
372
373 pseudo-device wsmux # mouse and keyboard multiplexor
374 pseudo-device wsfont
375