GENERIC32 revision 1.15 1 # $NetBSD: GENERIC32,v 1.15 2001/03/29 18:54:58 petrov Exp $
2
3 include "arch/sparc64/conf/std.sparc64"
4
5 #ident "GENERIC-$Revision: 1.15 $"
6
7 maxusers 64
8
9 ## System kernel configuration. See options(4) for more detail.
10
11
12 # Options for variants of the Sun SPARC architecure.
13 # We currently support three architecture types; at least one is required.
14 options SUN4U # sun4u - UltraSPARC
15 #options _LP64 # we're using a 64-bit compiler
16
17 ## System options specific to the sparc machine type
18
19 ## Use a faster console than the PROM's slow drawing routines. Not needed
20 ## for headless (no framebuffer) machines.
21 # XXX borken on sparc64
22 #options RASTERCONSOLE # fast rasterop console
23 #options FONT_GALLANT12x22 # the console font
24 #options FONT_BOLD8x16 # a somewhat smaller font
25
26 #### System options that are the same for all ports
27
28 ## Root device configuration: change the ?'s if you are going to use a
29 ## nonstandard root partition (other than where the kernel is booted from)
30 ## and/or nonstandard root type (not ffs or nfs). Normally this can be
31 ## automagically determined at boot time.
32
33 config netbsd root on ? type ?
34
35 ## UVM options.
36 #options UVM_PAGE_TRKOWN
37 #options UVMHIST
38 #options UVMHIST_PRINT # Loud!
39
40 ## System call tracing (see ktrace(1)).
41 options KTRACE
42
43 ## Collect statistics on kernel malloc's and free's. This does have a
44 ## significant performance hit on slower machines, so it is intended for
45 ## diagnostic use only.
46 #options KMEMSTATS
47
48 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2))
49 options SYSVMSG # System V message queues
50 options SYSVSEM # System V semaphores
51 options SYSVSHM # System V shared memory
52 #options SHMMAXPGS=1024 # 1024 pages is the default
53
54 ## Loadable kernel module support; still under development.
55 options LKM
56
57 ## NFS boot options; default on sparc is the bootparam protocol
58 options NFS_BOOT_BOOTPARAM
59 #options NFS_BOOT_BOOTP
60 #options NFS_BOOT_DHCP
61
62 #### Debugging options
63
64 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at
65 ## serial console break or keyboard reset, where the PROM would normally
66 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history.
67 # we enable DDB in GENERIC for now.
68 options DDB # kernel dynamic debugger
69 options DDB_HISTORY_SIZE=100 # enable history editing in DDB
70 #options DDB_ONPANIC # see also sysctl(8): `ddb.onpanic'
71
72 ## You may also use gdb, on another computer connected to this machine over
73 ## a serial port. Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is
74 ## a dev_t encoded device number of the serial port to use.
75 ## (0xc01 = ttya, 0xc02 = ttyb.)
76 #options KGDB # support for kernel gdb
77 #options KGDBDEV=0xc01 # kgdb device number (this sample is `ttyb')
78 #options KGDBRATE=38400 # baud rate
79
80
81 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file),
82 ## such that gdb(1) can be used on a kernel coredump.
83
84 #makeoptions DEBUG="-g"
85
86
87 ## Adds code to the kernel that does internal consistency checks, and will
88 ## cause the kernel to panic if corruption of internal data structures
89 ## is detected.
90 #options DIAGNOSTIC # extra kernel sanity checking
91
92 ## Enable (possibly expensive) debugging code that may also display messages
93 ## on the system console
94 #options DEBUG
95
96 ## Make SCSI error messages more verbose when explaining their meanings.
97 options SCSIVERBOSE
98 options PCIVERBOSE
99 options MIIVERBOSE # verbose PHY autoconfig messages
100 #options PCI_CONFIG_DUMP # verbosely dump PCI config space
101
102 ## `INSECURE' turns off the kernel security level (securelevel = 0 always).
103 ## This allows writing to /dev/mem, loading kernel modules while multi-user,
104 ## and other insecurities good only for development work. Do not use this
105 ## option on a production machine.
106 #options INSECURE
107
108 ## Allow non-root users to grab /dev/console with programs such as xconsole.
109 ## `xconsole' therefore does not need setuid root with this option enabled.
110 #options UCONSOLE
111
112 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a
113 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS',
114 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same
115 ## opaque file mechanism. Perl calls this "secure setuid scripts."
116
117 #options FDSCRIPTS
118 #options SETUIDSCRIPTS
119
120 ## Options for compatibility with previous releases foreign system binaries.
121 ## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up
122 ## additional user-level utilities or system configuration files. See
123 ## compat_sunos(8) and compat_svr4(8).
124
125 options COMPAT_43 # 4.3BSD system interfaces
126 options COMPAT_09 # NetBSD 0.9 binary compatibility
127 options COMPAT_10 # NetBSD 1.0 binary compatibility
128 options COMPAT_11 # NetBSD 1.1 binary compatibility
129 options COMPAT_12 # NetBSD 1.2 binary compatibility
130 options COMPAT_13 # NetBSD 1.3 binary compatibility
131 options COMPAT_14 # NetBSD 1.4 binary compatibility
132 options COMPAT_SUNOS # SunOS 4.x binary compatibility
133 options COMPAT_SVR4 # SunOS 5.x binary compatibility
134 #options COMPAT_SVR4_32 # SunOS 5.x 32-bit binary compatibility -- 64-bit only
135 #options COMPAT_NETBSD32 # NetBSD/sparc binary compatibility -- 64-bit only
136 options EXEC_AOUT # execve(2) support for a.out binaries
137 options EXEC_ELF32 # Exec module for SunOS 5.x binaries.
138 #options EXEC_ELF64 # Exec module for sparc64 & SunOs 5.x binaries. -- 64-bit only
139 #options SYSCALL_DEBUG
140
141 ## File systems. You probably need at least one of FFS or NFS.
142 file-system FFS # Berkeley Fast Filesystem
143 file-system NFS # Sun NFS-compatible filesystem client
144 file-system KERNFS # kernel data-structure filesystem
145 file-system NULLFS # NULL layered filesystem
146 file-system OVERLAY # overlay file system
147 file-system MFS # memory-based filesystem
148 file-system FDESC # user file descriptor filesystem
149 file-system UMAPFS # uid/gid remapping filesystem
150 file-system LFS # Log-based filesystem (still experimental)
151 file-system PORTAL # portal filesystem (still experimental)
152 file-system PROCFS # /proc
153 file-system CD9660 # ISO 9660 + Rock Ridge file system
154 file-system UNION # union file system
155 file-system MSDOSFS # MS-DOS FAT filesystem(s).
156
157 ## File system options.
158 options NFSSERVER # Sun NFS-compatible filesystem server
159 options QUOTA # FFS quotas
160 #options FFS_EI # FFS Endian Independent support
161 options SOFTDEP # FFS soft updates support.
162
163 ## Network protocol support. In most environments, INET is required.
164 options INET # IP (Internet Protocol) v4
165 options INET6 # IPV6
166 #options IPSEC # IP security
167 #options IPSEC_ESP # IP security (encryption part; define w/IPSEC)
168 #options IPSEC_DEBUG # debug for IP security
169 options TCP_COMPAT_42 # 4.2BSD IP implementation compatibility
170 #options GATEWAY # packet forwarding ("router switch")
171 options MROUTING # packet forwarding of multicast packets
172 #options DIRECTED_BROADCAST # allow broadcasts through routers
173 options NS # Xerox NS networking
174 #options NSIP # Xerox NS tunneling over IP
175 options ISO,TPIP # OSI networking
176 options EON # OSI tunneling over IP
177 #options CCITT,LLC,HDLC # X.25 packet switched protocol
178 options NETATALK # AppleTalk (over Ethernet) protocol
179 options NTP # Network Time Protocol in-kernel support
180 #options PPS_SYNC # Add serial line synchronization for NTP
181 options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs.
182 options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device
183 options PPP_BSDCOMP # Add BSD compression to ppp device
184 options PPP_DEFLATE # Add deflate (libz) compression to ppp device
185 options PPP_FILTER # Add active filters for ppp (via bpf)
186
187
188 #### Main bus and CPU .. all systems.
189 mainbus0 at root
190 cpu0 at mainbus0
191
192 #### Bus types found on SPARC systems.
193
194 sbus0 at mainbus0 # Ultra 1
195 #upa0 at mainbus0 # Ultra 1E, Ultra 2, Ex0000
196 psycho* at mainbus0 # Darwin, Ultra5
197 pci* at psycho?
198 pci* at simba?
199 simba* at pci? dev ? function ? # `APB' support.
200 ebus* at pci? # ebus devices
201
202 #### Standard system devices -- all required for a given architecture
203
204 ## PROM console driver -- if all else fails
205 pcons0 at mainbus0 # PROM console
206
207 ## Auxiliary system registers -- We use the OBP for power management
208 auxio* at ebus? # auxio registers
209 auxio* at sbus? slot ? offset ? # auxio registers
210
211 # We also need:
212 bpp* at sbus? slot ? offset ? # parallel port
213 lpt* at ebus? # parallel port
214
215 ## Mostek clock found on 4/300, sun4c, sun4m and sun4u systems.
216 ## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems.
217 clock* at sbus? slot ? offset ?
218 clock* at ebus?
219
220 ## Timer chip found on 4/300, sun4c, sun4m and (some) sun4u systems.
221 timer* at mainbus0 # sun4c
222
223 #### Serial port configuration
224
225 ## Zilog 8530 serial chips. Each has two-channels.
226 ## zs0 is ttya and ttyb. zs1 is the keyboard and mouse.
227 zs* at sbus? slot ? offset ?
228 zstty* at zs? channel ? # ttya
229 kbd0 at zstty?
230 ms0 at zstty?
231
232 ## PCI machines have serial ports:
233 ## Siemens SAB82532 controller: ttya and ttyb (`su'; sab)
234 ## Part of NS PC87332VLJ Super I/O controller: kbd/mouse (`se'; com)
235
236 ## The SAB82532 controller has two serial ports
237 #sab* at ebus? # ttya/ttyb
238 #sabtty* at sab? channel ?
239
240 ## Part of a PC87332VLJ
241 com* at ebus? # `com' driver for `su'
242 kbd0 at com? # keyboard
243 ms0 at com? # mouse
244
245 #### Disk controllers and disks
246
247 ## The following flags may be set for the NCR53c94 based esp driver:
248 ## bits 0-7: disable disconnect/reselect for the corresponding target
249 ## bits 8-15: disable synchronous negotiation for target [bit-8]
250
251 ## sun4u on-board SCSI, and FSBE/S SBus SCSI cards, an NCR53c94 or
252 ## equivalent behind an LSI Logic DMA controller
253
254 dma* at sbus? slot ? offset ? # SBus
255 esp* at dma? flags 0x0000 # SBus
256
257 ## FAS supported by esp driver
258 esp* at sbus? slot ? offset ?
259
260 scsibus* at esp?
261
262 ## Qlogic ISP SBus or PCI SCSI Card
263 isp* at sbus? slot ? offset ?
264 isp* at pci?
265 scsibus* at isp?
266
267 ## GLM support
268 siop* at pci? # 53C875 "glm" compatible
269 scsibus* at siop?
270
271 ## These entries find devices on all SCSI busses and assign
272 ## unit numbers dynamically.
273 sd* at scsibus? target ? lun ? # SCSI disks
274 st* at scsibus? target ? lun ? # SCSI tapes
275 cd* at scsibus? target ? lun ? # SCSI CD-ROMs
276 ch* at scsibus? target ? lun ? # SCSI changer devices
277 ss* at scsibus? target ? lun ? # SCSI scanners
278 ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE devices
279 uk* at scsibus? target ? lun ? # unknown SCSI
280
281 # PCI IDE.
282 pciide* at pci ? dev ? function ? flags 0x0000
283 wd* at pciide? channel ? drive ? flags 0x0000
284 atapibus* at pciide? channel ?
285
286 cd* at atapibus? drive ? flags 0x0000 # ATAPI CD-ROM drives
287 sd* at atapibus? drive ? flags 0x0000 # ATAPI disk drives
288 uk* at atapibus? drive ? flags 0x0000 # ATAPI unknown
289
290 ## Floppy controller and drive found on SPARCstations.
291
292 # need share with the sparc, and everyone else. needs to use auxio.
293 # actually, the ebus version has (will have) direct access to it's AUXIO
294 # register space (it is mapped in to fdthree not auxio).
295 #fdc0 at sbus? slot ? offset ? # SUNW,fdtwo
296 #fdc0 at ebus? # fdthree
297 #fd* at fdc0 # the drive itself
298
299 ## A disk-like interface to files. Can be used to create floppy, CD,
300 ## miniroot images, etc.
301
302 pseudo-device vnd 4
303
304 ## Concatenated and striped disks; with this, you can create a software-based
305 ## disk array similar to a "RAID 0" setup. See ccd(4).
306
307 pseudo-device ccd 4
308
309 ## RAIDframe disk driver: software RAID driver. See raid(4).
310
311 pseudo-device raid 4
312 #options RAID_AUTOCONFIG # auto-configuration of RAID components
313
314 ## Memory disk device, used on boot floppies with compressed
315 ## kernel-plus-root-disk images.
316
317 pseudo-device md 1
318
319
320 #### Network interfaces
321
322 ## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue
323 ## Three flavors of additional SBus ethernets are available. One attaches
324 ## directly like the sun4c on-board, one uses the ledma device like the
325 ## sun4m on-board, and one uses the lebuffer device.
326
327 ledma0 at sbus? slot ? offset ? # sun4m on-board
328 le0 at ledma0 # sun4m on-board
329 le* at sbus? slot ? offset ? # SBus
330 ledma* at sbus? slot ? offset ? # SBus
331 le* at ledma? # SBus
332 lebuffer0 at sbus? slot ? offset ? # SBus
333 le0 at lebuffer? # SBus
334 lebuffer* at sbus? slot ? offset ? # SBus
335 le* at lebuffer? # SBus
336
337 ## Happy Meal Ethernet
338 hme* at sbus? slot ? offset ?
339 hme* at pci? dev ? function ? # network "hme" compatible
340
341 # MII/PHY support
342 # XXX: only nsphy "tested"
343 exphy* at mii? phy ? # 3Com internal PHYs
344 icsphy* at mii? phy ? # Integrated Circuit Systems ICS1890
345 inphy* at mii? phy ? # Intel 82555 PHYs
346 lxtphy* at mii? phy ? # Level One LXT-970 PHYs
347 nsphy* at mii? phy ? # NS83840 PHYs
348 qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs
349 sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs
350 tlphy* at mii? phy ? # ThunderLAN PHYs
351 ukphy* at mii? phy ? # generic unknown PHYs
352
353 ## qec/be, qec/hme
354 qec* at sbus? slot ? offset ?
355 be* at qec?
356 qe* at qec?
357
358 ## Loopback network interface; required
359 pseudo-device loop
360
361 ## SLIP and CSLIP interfaces, for IP over a serial line.
362 pseudo-device sl 2
363
364 ## PPP, the successor to SLIP. See pppd(8).
365 pseudo-device ppp 2
366
367 ## Starmode Radio IP, a special hardware network device.
368 pseudo-device strip 1
369
370 ## Network "tunnel" device, allowing protocol stacks to run in the userland.
371 ## This is used by the third-party user-mode "ppp" program, and others.
372 pseudo-device tun 4
373
374 ## Generic L3 over IP tunnel
375 #pseudo-device gre 2 # generic L3 over IP tunnel
376
377 ## Berkeley Packet Filter, required to run RARPD. A generic C-language
378 ## interface that allows selective examining of incoming packets.
379 pseudo-device bpfilter 8
380
381 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for
382 ## one example of the use of the IP Filter.
383 pseudo-device ipfilter
384
385 ## for IPv6
386 pseudo-device gif 4 # IPv[46] over IPv[46] tunnel (RFC1933)
387 #pseudo-device faith 1 # IPv[46] tcp relay translation i/f
388 #pseudo-device stf 1 # 6to4 IPv6 over IPv4 encapsulation
389
390
391 #### Audio and video devices
392
393 ## /dev/audio support (`audiocs' plus `audio')
394 ##
395 audiocs* at sbus? slot ? offset ? # SUNW,CS4231
396 audio* at audiocs?
397
398
399 ## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m
400 ## systems. If your sun4 system has a cgfour installed in the P4 slot,
401 ## the P4 entries for "bwtwo" will attach to the overlay plane of the
402 ## "cgfour".
403
404 #bwtwo0 at sbus? slot ? offset ? # sun4c and sun4m
405 #bwtwo* at sbus? slot ? offset ?
406
407 ## Sun "cgthree" Sbus color framebuffer
408 #cgthree0 at sbus? slot ? offset ?
409 #cgthree* at sbus? slot ? offset ?
410
411 ## Sun "cgsix" accelerated color framebuffer.
412 cgsix0 at sbus? slot ? offset ?
413 cgsix* at sbus? slot ? offset ?
414
415 ## Sun FFB not supported
416 #ffb* at upa?
417
418 #### Other device configuration
419
420 ## Pseudo ttys, required for network logins and programs like screen.
421
422 pseudo-device pty # pseudo-ttys (for network, etc.)
423
424 ## Random device, used to implement /dev/random (a source of random noise),
425 ## and generate randomness for some kernel formulae.
426
427 pseudo-device rnd
428