GENERIC32 revision 1.21
1 # $NetBSD: GENERIC32,v 1.21 2001/09/21 22:08:41 eeh Exp $ 2 3 include "arch/sparc64/conf/std.sparc64" 4 5 #ident "GENERIC-$Revision: 1.21 $" 6 7 maxusers 64 8 9 ## System kernel configuration. See options(4) for more detail. 10 11 12 # Options for variants of the Sun SPARC architecure. 13 # We currently support three architecture types; at least one is required. 14 options SUN4U # sun4u - UltraSPARC 15 #options _LP64 # we're using a 64-bit compiler 16 17 ## System options specific to the sparc machine type 18 19 ## Use a faster console than the PROM's slow drawing routines. Not needed 20 ## for headless (no framebuffer) machines. 21 # XXX borken on sparc64 22 #options RASTERCONSOLE # fast rasterop console 23 #options FONT_GALLANT12x22 # the console font 24 #options FONT_BOLD8x16 # a somewhat smaller font 25 26 #### System options that are the same for all ports 27 28 ## Root device configuration: change the ?'s if you are going to use a 29 ## nonstandard root partition (other than where the kernel is booted from) 30 ## and/or nonstandard root type (not ffs or nfs). Normally this can be 31 ## automagically determined at boot time. 32 33 config netbsd root on ? type ? 34 35 ## UVM options. 36 #options UVM_PAGE_TRKOWN 37 #options UVMHIST 38 #options UVMHIST_PRINT # Loud! 39 40 ## System call tracing (see ktrace(1)). 41 options KTRACE 42 43 ## Collect statistics on kernel malloc's and free's. This does have a 44 ## significant performance hit on slower machines, so it is intended for 45 ## diagnostic use only. 46 #options KMEMSTATS 47 48 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 49 options SYSVMSG # System V message queues 50 options SYSVSEM # System V semaphores 51 options SYSVSHM # System V shared memory 52 #options SHMMAXPGS=1024 # 1024 pages is the default 53 54 ## Loadable kernel module support; still under development. 55 options LKM 56 57 ## NFS boot options; default on sparc is the bootparam protocol 58 options NFS_BOOT_BOOTPARAM 59 #options NFS_BOOT_BOOTP 60 #options NFS_BOOT_DHCP 61 62 #### Debugging options 63 64 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 65 ## serial console break or keyboard reset, where the PROM would normally 66 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 67 # we enable DDB in GENERIC for now. 68 options DDB # kernel dynamic debugger 69 options DDB_HISTORY_SIZE=100 # enable history editing in DDB 70 #options DDB_ONPANIC # see also sysctl(8): `ddb.onpanic' 71 72 ## You may also use gdb, on another computer connected to this machine over 73 ## a serial port. Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is 74 ## a dev_t encoded device number of the serial port to use. 75 ## (0xc01 = ttya, 0xc02 = ttyb.) 76 #options KGDB # support for kernel gdb 77 #options KGDBDEV=0xc01 # kgdb device number (this sample is `ttyb') 78 #options KGDBRATE=38400 # baud rate 79 80 81 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 82 ## such that gdb(1) can be used on a kernel coredump. 83 84 #makeoptions DEBUG="-g" 85 86 87 ## Adds code to the kernel that does internal consistency checks, and will 88 ## cause the kernel to panic if corruption of internal data structures 89 ## is detected. 90 #options DIAGNOSTIC # extra kernel sanity checking 91 92 ## Enable (possibly expensive) debugging code that may also display messages 93 ## on the system console 94 #options DEBUG 95 96 ## Make SCSI error messages more verbose when explaining their meanings. 97 options SCSIVERBOSE 98 options PCIVERBOSE 99 options MIIVERBOSE # verbose PHY autoconfig messages 100 #options PCI_CONFIG_DUMP # verbosely dump PCI config space 101 102 ## `INSECURE' turns off the kernel security level (securelevel = 0 always). 103 ## This allows writing to /dev/mem, loading kernel modules while multi-user, 104 ## and other insecurities good only for development work. Do not use this 105 ## option on a production machine. 106 #options INSECURE 107 108 ## Allow non-root users to grab /dev/console with programs such as xconsole. 109 ## `xconsole' therefore does not need setuid root with this option enabled. 110 #options UCONSOLE 111 112 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a 113 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 114 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 115 ## opaque file mechanism. Perl calls this "secure setuid scripts." 116 117 #options FDSCRIPTS 118 #options SETUIDSCRIPTS 119 120 ## Options for compatibility with previous releases foreign system binaries. 121 ## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 122 ## additional user-level utilities or system configuration files. See 123 ## compat_sunos(8) and compat_svr4(8). 124 125 options COMPAT_43 # 4.3BSD system interfaces 126 options COMPAT_09 # NetBSD 0.9 binary compatibility 127 options COMPAT_10 # NetBSD 1.0 binary compatibility 128 options COMPAT_11 # NetBSD 1.1 binary compatibility 129 options COMPAT_12 # NetBSD 1.2 binary compatibility 130 options COMPAT_13 # NetBSD 1.3 binary compatibility 131 options COMPAT_14 # NetBSD 1.4 binary compatibility 132 options COMPAT_SUNOS # SunOS 4.x binary compatibility 133 options COMPAT_SVR4 # SunOS 5.x binary compatibility 134 #options COMPAT_SVR4_32 # SunOS 5.x 32-bit binary compatibility -- 64-bit only 135 #options COMPAT_NETBSD32 # NetBSD/sparc binary compatibility -- 64-bit only 136 options EXEC_AOUT # execve(2) support for a.out binaries 137 options EXEC_ELF32 # Exec module for SunOS 5.x binaries. 138 #options EXEC_ELF64 # Exec module for sparc64 & SunOs 5.x binaries. -- 64-bit only 139 #options SYSCALL_DEBUG 140 141 #options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended. 142 143 ## File systems. You probably need at least one of FFS or NFS. 144 file-system FFS # Berkeley Fast Filesystem 145 file-system NFS # Sun NFS-compatible filesystem client 146 file-system KERNFS # kernel data-structure filesystem 147 file-system NULLFS # NULL layered filesystem 148 file-system OVERLAY # overlay file system 149 file-system MFS # memory-based filesystem 150 file-system FDESC # user file descriptor filesystem 151 file-system UMAPFS # uid/gid remapping filesystem 152 file-system LFS # Log-based filesystem (still experimental) 153 file-system PORTAL # portal filesystem (still experimental) 154 file-system PROCFS # /proc 155 file-system CD9660 # ISO 9660 + Rock Ridge file system 156 file-system UNION # union file system 157 file-system MSDOSFS # MS-DOS FAT filesystem(s). 158 159 ## File system options. 160 options NFSSERVER # Sun NFS-compatible filesystem server 161 options QUOTA # FFS quotas 162 #options FFS_EI # FFS Endian Independent support 163 options SOFTDEP # FFS soft updates support. 164 165 ## Network protocol support. In most environments, INET is required. 166 options INET # IP (Internet Protocol) v4 167 options INET6 # IPV6 168 #options IPSEC # IP security 169 #options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 170 #options IPSEC_DEBUG # debug for IP security 171 #options GATEWAY # packet forwarding ("router switch") 172 options MROUTING # packet forwarding of multicast packets 173 #options DIRECTED_BROADCAST # allow broadcasts through routers 174 options NS # Xerox NS networking 175 #options NSIP # Xerox NS tunneling over IP 176 options ISO,TPIP # OSI networking 177 options EON # OSI tunneling over IP 178 #options CCITT,LLC,HDLC # X.25 packet switched protocol 179 options NETATALK # AppleTalk (over Ethernet) protocol 180 options NTP # Network Time Protocol in-kernel support 181 #options PPS_SYNC # Add serial line synchronization for NTP 182 options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 183 options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 184 options PPP_BSDCOMP # Add BSD compression to ppp device 185 options PPP_DEFLATE # Add deflate (libz) compression to ppp device 186 options PPP_FILTER # Add active filters for ppp (via bpf) 187 #options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG 188 189 190 #### Main bus and CPU .. all systems. 191 mainbus0 at root 192 cpu0 at mainbus0 193 194 #### Bus types found on SPARC systems. 195 196 sbus0 at mainbus0 # Ultra 1 197 #upa0 at mainbus0 # Ultra 1E, Ultra 2, Ex0000 198 psycho* at mainbus0 # Darwin, Ultra5 199 pci* at psycho? 200 pci* at ppb? 201 ppb* at pci? dev ? function ? # `APB' support. 202 #pci* at simba? 203 #simba* at pci? dev ? function ? # `APB' support. 204 ebus* at pci? # ebus devices 205 # XXX 'puc's aren't really bridges, but there's no better place for them here 206 puc* at pci? dev ? function ? # PCI "universal" comm. cards 207 208 #### Standard system devices -- all required for a given architecture 209 210 ## PROM console driver -- if all else fails 211 pcons0 at mainbus0 # PROM console 212 213 ## Auxiliary system registers -- We use the OBP for power management 214 auxio* at ebus? # auxio registers 215 auxio* at sbus? slot ? offset ? # auxio registers 216 217 # We also need: 218 bpp* at sbus? slot ? offset ? # parallel port 219 lpt* at ebus? # parallel port 220 221 ## Mostek clock found on 4/300, sun4c, sun4m and sun4u systems. 222 ## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 223 clock* at sbus? slot ? offset ? 224 clock* at ebus? 225 226 ## Timer chip found on 4/300, sun4c, sun4m and (some) sun4u systems. 227 timer* at mainbus0 # sun4c 228 229 #### Serial port configuration 230 231 ## Zilog 8530 serial chips. Each has two-channels. 232 ## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 233 zs* at sbus? slot ? offset ? 234 zstty* at zs? channel ? # ttya 235 kbd0 at zstty? 236 ms0 at zstty? 237 238 ## PCI machines have serial ports: 239 ## Siemens SAB82532 controller: ttya and ttyb (`su'; sab) 240 ## Part of NS PC87332VLJ Super I/O controller: kbd/mouse (`se'; com) 241 242 ## The SAB82532 controller has two serial ports 243 #sab* at ebus? # ttya/ttyb 244 #sabtty* at sab? channel ? 245 246 ## Part of a PC87332VLJ 247 com* at ebus? # `com' driver for `su' 248 kbd0 at com? # keyboard 249 ms0 at com? # mouse 250 251 # PCI serial interfaces 252 com* at puc? port ? # 16x50s on "universal" comm boards 253 cy* at pci? dev ? function ? # Cyclades Cyclom-Y serial boards 254 cz* at pci? dev ? function ? # Cyclades-Z multi-port serial boards 255 256 #### Disk controllers and disks 257 258 ## The following flags may be set for the NCR53c94 based esp driver: 259 ## bits 0-7: disable disconnect/reselect for the corresponding target 260 ## bits 8-15: disable synchronous negotiation for target [bit-8] 261 262 ## sun4u on-board SCSI, and FSBE/S SBus SCSI cards, an NCR53c94 or 263 ## equivalent behind an LSI Logic DMA controller 264 265 dma* at sbus? slot ? offset ? # SBus 266 esp* at dma? flags 0x0000 # SBus 267 268 ## FAS supported by esp driver 269 esp* at sbus? slot ? offset ? 270 271 scsibus* at esp? 272 273 ## Qlogic ISP SBus or PCI SCSI Card 274 isp* at sbus? slot ? offset ? 275 isp* at pci? 276 scsibus* at isp? 277 278 ## GLM support 279 siop* at pci? # 53C875 "glm" compatible 280 scsibus* at siop? 281 282 # PCI SCSI controllers (untested) 283 adv* at pci? dev ? function ? # AdvanSys 1200[A,B], 9xx[U,UA] SCSI 284 adw* at pci? dev ? function ? # AdvanSys 9x0UW[D], 3940U[2,3]W SCSI 285 ahc* at pci? dev ? function ? # Adaptec [23]94x, aic78x0 SCSI 286 bha* at pci? dev ? function ? # BusLogic 9xx SCSI 287 dpt* at pci? dev ? function ? # DPT SmartCache/SmartRAID 288 pcscp* at pci? dev ? function ? # AMD 53c974 PCscsi-PCI SCSI 289 290 scsibus* at scsi? 291 292 ## These entries find devices on all SCSI busses and assign 293 ## unit numbers dynamically. 294 sd* at scsibus? target ? lun ? # SCSI disks 295 st* at scsibus? target ? lun ? # SCSI tapes 296 cd* at scsibus? target ? lun ? # SCSI CD-ROMs 297 ch* at scsibus? target ? lun ? # SCSI changer devices 298 ss* at scsibus? target ? lun ? # SCSI scanners 299 ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE devices 300 uk* at scsibus? target ? lun ? # unknown SCSI 301 302 # PCI IDE. 303 pciide* at pci ? dev ? function ? flags 0x0000 304 atapibus* at pciide? channel ? 305 306 ## Disable UDMA 4 which causes data corruption on the Acer Labs 307 ## chipset on Sun Blade 100 and Netra X1 machines. 308 wd* at pciide? channel ? drive ? flags 0x0a00 # Disable UDMA 4 309 310 311 cd* at atapibus? drive ? flags 0x0000 # ATAPI CD-ROM drives 312 sd* at atapibus? drive ? flags 0x0000 # ATAPI disk drives 313 uk* at atapibus? drive ? flags 0x0000 # ATAPI unknown 314 315 # RAID controllers and devices (untested) 316 cac* at pci? dev ? function ? # Compaq PCI array controllers 317 mlx* at pci? dev ? function ? # Mylex DAC960 & DEC SWXCR family 318 twe* at pci? dev ? function ? # 3ware Escalade RAID controllers 319 320 ld* at cac? unit ? # logical disk devices 321 ld* at twe? unit ? 322 ld* at mlx? unit ? 323 324 ## Floppy controller and drive found on SPARCstations. 325 326 # need share with the sparc, and everyone else. needs to use auxio. 327 # actually, the ebus version has (will have) direct access to it's AUXIO 328 # register space (it is mapped in to fdthree not auxio). 329 #fdc0 at sbus? slot ? offset ? # SUNW,fdtwo 330 #fdc0 at ebus? # fdthree 331 #fd* at fdc0 # the drive itself 332 333 ## A disk-like interface to files. Can be used to create floppy, CD, 334 ## miniroot images, etc. 335 336 pseudo-device vnd 4 337 338 ## Concatenated and striped disks; with this, you can create a software-based 339 ## disk array similar to a "RAID 0" setup. See ccd(4). 340 341 pseudo-device ccd 4 342 343 ## RAIDframe disk driver: software RAID driver. See raid(4). 344 345 pseudo-device raid 4 346 #options RAID_AUTOCONFIG # auto-configuration of RAID components 347 348 ## Memory disk device, used on boot floppies with compressed 349 ## kernel-plus-root-disk images. 350 351 pseudo-device md 1 352 353 354 #### Network interfaces 355 356 ## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 357 ## Three flavors of additional SBus ethernets are available. One attaches 358 ## directly like the sun4c on-board, one uses the ledma device like the 359 ## sun4m on-board, and one uses the lebuffer device. 360 361 ledma0 at sbus? slot ? offset ? # sun4m on-board 362 le0 at ledma0 # sun4m on-board 363 le* at sbus? slot ? offset ? # SBus 364 ledma* at sbus? slot ? offset ? # SBus 365 le* at ledma? # SBus 366 lebuffer0 at sbus? slot ? offset ? # SBus 367 le0 at lebuffer? # SBus 368 lebuffer* at sbus? slot ? offset ? # SBus 369 le* at lebuffer? # SBus 370 371 ## Happy Meal Ethernet 372 hme* at sbus? slot ? offset ? 373 hme* at pci? dev ? function ? # network "hme" compatible 374 375 ## qec/be, qec/hme 376 qec* at sbus? slot ? offset ? 377 be* at qec? 378 qe* at qec? 379 380 # PCI network interfaces 381 # UT marks untested. 382 an* at pci? dev ? function ? # Aironet PC4500/PC4800 (802.11) UT 383 de* at pci? dev ? function ? # DEC 21x4x-based Ethernet UT 384 en* at pci? dev ? function ? # ENI/Adaptec ATM UT 385 # XXX causes ICE 386 #ep* at pci? dev ? function ? # 3Com 3c59x 387 ex* at pci? dev ? function ? # 3Com 90x[B] UT 388 epic* at pci? dev ? function ? # SMC EPIC/100 Ethernet UT 389 esh* at pci? dev ? function ? # Essential HIPPI card UT 390 fpa* at pci? dev ? function ? # DEC DEFPA FDDI UT 391 fxp* at pci? dev ? function ? # Intel EtherExpress PRO 10+/100B UT 392 gem* at pci? dev ? function ? # Apple GMAC and Sun ERI gigabit enet 393 le* at pci? dev ? function ? # PCnet-PCI Ethernet UT 394 # XXX uses vtophys() 395 #lmc* at pci? dev ? function ? # Lan Media Corp SSI/HSSI/DS3 396 ne* at pci? dev ? function ? # NE2000-compatible Ethernet UT 397 ntwoc* at pci? dev ? function ? # Riscom/N2 PCI Sync Serial UT 398 rtk* at pci? dev ? function ? # Realtek 8129/8139 UT 399 sip* at pci? dev ? function ? # SiS 900 Ethernet UT 400 ti* at pci? dev ? function ? # Alteon ACEnic gigabit Ethernet UT 401 # XXX uses vtophys() 402 #tl* at pci? dev ? function ? # ThunderLAN-based Ethernet 403 tlp* at pci? dev ? function ? # DECchip 21x4x (and clones) Ethernet 404 #options TLP_MATCH_21040 405 #options TLP_MATCH_21041 406 #options TLP_MATCH_21140 407 #options TLP_MATCH_21142 408 vr* at pci? dev ? function ? # VIA Rhine Fast Ethernet 409 410 # MII/PHY support 411 # XXX: only nsphy "tested" 412 dmphy* at mii? phy ? # Davicom DM9101 PHYs 413 exphy* at mii? phy ? # 3Com internal PHYs 414 icsphy* at mii? phy ? # Integrated Circuit Systems ICS1890 415 inphy* at mii? phy ? # Intel 82555 PHYs 416 iophy* at mii? phy ? # Intel 82553 PHYs 417 lxtphy* at mii? phy ? # Level One LXT-970 PHYs 418 nsphy* at mii? phy ? # NS83840 PHYs 419 nsphyter* at mii? phy ? # NS83843 PHYs 420 qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 421 sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 422 tlphy* at mii? phy ? # ThunderLAN PHYs 423 tqphy* at mii? phy ? # TDK Semiconductor PHYs 424 ukphy* at mii? phy ? # generic unknown PHYs 425 426 # PCI USB controllers 427 ohci* at pci? dev ? function ? # Open Host Controller 428 429 usb* at ohci? # USB bus support 430 uhub* at usb? # USB Hubs 431 uhub* at uhub? port ? configuration ? interface ? 432 433 uhid* at uhub? port ? configuration ? interface ? # USB Generic HID 434 ulpt* at uhub? port ? configuration ? interface ? # USB Printer 435 436 umodem* at uhub? port ? configuration ? # USB Modem 437 ucom* at umodem? 438 439 umass* at uhub? port ? configuration ? interface ? # USB Mass Storage 440 atapibus* at umass? channel ? 441 scsibus* at umass? channel ? 442 443 uaudio* at uhub? port ? configuration ? # USB audio 444 445 # USB Ethernet adapters 446 aue* at uhub? port ? # ADMtek AN986 Pegasus based adapters 447 cue* at uhub? port ? # CATC USB-EL1201A based adapters 448 kue* at uhub? port ? # Kawasaki LSI KL5KUSB101B based adapters 449 450 uscanner* at uhub? port ? # USB scanners 451 uyap* at uhub? port ? # Y@P firmware loader 452 ugen* at uhub? port ? configuration ? interface ? # USB Generic driver 453 454 # PCI IEEE1394 controllers 455 fwohci* at pci? dev ? function ? # IEEE1394 Open Host Controller 456 #fwlynx* at pci? dev ? function ? # IEEE1394 TI Lynx Controller 457 fw* at fwbus? # IP over 1394 458 459 # IEEE1394 nodes 460 #fwnode* at fwbus? oui ? devhi ? devlo ? 461 #scsibus* at fwnode? 462 463 ## Loopback network interface; required 464 pseudo-device loop 465 466 ## SLIP and CSLIP interfaces, for IP over a serial line. 467 pseudo-device sl 2 468 469 ## PPP, the successor to SLIP. See pppd(8). 470 pseudo-device ppp 2 471 472 ## Starmode Radio IP, a special hardware network device. 473 pseudo-device strip 1 474 475 ## Network "tunnel" device, allowing protocol stacks to run in the userland. 476 ## This is used by the third-party user-mode "ppp" program, and others. 477 pseudo-device tun 4 478 479 ## Generic L3 over IP tunnel 480 #pseudo-device gre 2 # generic L3 over IP tunnel 481 482 ## Berkeley Packet Filter, required to run RARPD. A generic C-language 483 ## interface that allows selective examining of incoming packets. 484 pseudo-device bpfilter 8 485 486 ## Simple inter-network traffic bridging 487 pseudo-device bridge 488 489 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for 490 ## one example of the use of the IP Filter. 491 pseudo-device ipfilter 492 493 ## for IPv6 494 pseudo-device gif 4 # IPv[46] over IPv[46] tunnel (RFC1933) 495 #pseudo-device faith 1 # IPv[46] tcp relay translation i/f 496 #pseudo-device stf 1 # 6to4 IPv6 over IPv4 encapsulation 497 498 499 #### Audio and video devices 500 501 ## /dev/audio support (`audiocs' plus `audio') 502 ## 503 audiocs* at sbus? slot ? offset ? # SUNW,CS4231 504 audio* at audiocs? 505 506 507 ## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 508 ## systems. If your sun4 system has a cgfour installed in the P4 slot, 509 ## the P4 entries for "bwtwo" will attach to the overlay plane of the 510 ## "cgfour". 511 512 #bwtwo0 at sbus? slot ? offset ? # sun4c and sun4m 513 #bwtwo* at sbus? slot ? offset ? 514 515 ## Sun "cgthree" Sbus color framebuffer 516 #cgthree0 at sbus? slot ? offset ? 517 #cgthree* at sbus? slot ? offset ? 518 519 ## Sun "cgsix" accelerated color framebuffer. 520 cgsix0 at sbus? slot ? offset ? 521 cgsix* at sbus? slot ? offset ? 522 523 ## Sun FFB not supported 524 #ffb* at upa? 525 526 #### Other device configuration 527 528 ## Pseudo ttys, required for network logins and programs like screen. 529 530 pseudo-device pty # pseudo-ttys (for network, etc.) 531 532 ## Random device, used to implement /dev/random (a source of random noise), 533 ## and generate randomness for some kernel formulae. 534 535 pseudo-device rnd 536
Indexes created Wed Oct 15 16:09:53 GMT 2025