GENERIC32 revision 1.3
1# $NetBSD: GENERIC32,v 1.3 2000/07/31 13:16:24 mrg Exp $ 2 3include "arch/sparc64/conf/std.sparc64" 4 5#ident "GENERIC-$Revision: 1.3 $" 6 7maxusers 32 8 9## System kernel configuration. See options(4) for more detail. 10 11 12# Options for variants of the Sun SPARC architecure. 13# We currently support three architecture types; at least one is required. 14options SUN4U # sun4u - Ultra 140 and 170 15options TRAPWIN 16options __ELF__ # we use elf 17#options _LP64 # we're using a 64-bit compiler 18 19## System options specific to the sparc machine type 20 21## Use a faster console than the PROM's slow drawing routines. Not needed 22## for headless (no framebuffer) machines. 23# XXX broken on sparc64 24#options RASTERCONSOLE # fast rasterop console 25#options FONT_GALLANT12x22 # the console font 26#options FONT_BOLD8x16 # a somewhat smaller font 27 28#### System options that are the same for all ports 29 30## Root device configuration: change the ?'s if you are going to use a 31## nonstandard root partition (other than where the kernel is booted from) 32## and/or nonstandard root type (not ffs or nfs). Normally this can be 33## automagically determined at boot time. 34 35config netbsd root on ? type ? 36 37## UVM options. 38#options UVM_PAGE_TRKOWN 39#options UVMHIST 40#options UVMHIST_PRINT # Loud! 41 42## System call tracing (see ktrace(1)). 43options KTRACE 44 45## Collect statistics on kernel malloc's and free's. This does have a 46## significant performance hit on slower machines, so it is intended for 47## diagnostic use only. 48#options KMEMSTATS 49 50## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 51options SYSVMSG # System V message queues 52options SYSVSEM # System V semaphores 53options SYSVSHM # System V shared memory 54#options SHMMAXPGS=1024 # 1024 pages is the default 55 56## Loadable kernel module support; still under development. 57options LKM 58 59## NFS boot options; default on sparc is the bootparam protocol 60options NFS_BOOT_BOOTPARAM 61#options NFS_BOOT_BOOTP 62#options NFS_BOOT_DHCP 63 64#### Debugging options 65 66## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 67## serial console break or keyboard reset, where the PROM would normally 68## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 69# we enable DDB in GENERIC for now. 70options DDB # kernel dynamic debugger 71options DDB_HISTORY_SIZE=100 # enable history editing in DDB 72#options DDB_ONPANIC # see also sysctl(8): `ddb.onpanic' 73 74## You may also use gdb, on another computer connected to this machine over 75## a serial port. Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is 76## a dev_t encoded device number of the serial port to use. 77## (0xc01 = ttya, 0xc02 = ttyb.) 78#options KGDB # support for kernel gdb 79#options KGDBDEV=0xc01 # kgdb device number (this sample is `ttyb') 80#options KGDBRATE=38400 # baud rate 81 82 83## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 84## such that gdb(1) can be used on a kernel coredump. 85 86makeoptions DEBUG="-g" 87 88 89## Adds code to the kernel that does internal consistency checks, and will 90## cause the kernel to panic if corruption of internal data structures 91## is detected. 92#options DIAGNOSTIC # extra kernel sanity checking 93 94## Enable (possibly expensive) debugging code that may also display messages 95## on the system console 96options DEBUG 97 98## Make SCSI error messages more verbose when explaining their meanings. 99options SCSIVERBOSE 100options PCIVERBOSE 101options MIIVERBOSE # verbose PHY autoconfig messages 102#options PCI_CONFIG_DUMP # verbosely dump PCI config space 103 104## `INSECURE' turns off the kernel security level (securelevel = 0 always). 105## This allows writing to /dev/mem, loading kernel modules while multi-user, 106## and other insecurities good only for development work. Do not use this 107## option on a production machine. 108#options INSECURE 109 110## Allow non-root users to grab /dev/console with programs such as xconsole. 111## `xconsole' therefore does not need setuid root with this option enabled. 112#options UCONSOLE 113 114## `FDSCRIPTS' allows non-readable but executable scripts by providing a 115## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 116## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 117## opaque file mechanism. Perl calls this "secure setuid scripts." 118 119#options FDSCRIPTS 120#options SETUIDSCRIPTS 121 122## Options for compatibility with previous releases foreign system binaries. 123## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 124## additional user-level utilities or system configuration files. See 125## compat_sunos(8) and compat_svr4(8). 126 127options COMPAT_43 # 4.3BSD system interfaces 128options COMPAT_10 # NetBSD 1.0 binary compatibility 129options COMPAT_11 # NetBSD 1.1 binary compatibility 130options COMPAT_12 # NetBSD 1.2 binary compatibility 131options COMPAT_13 # NetBSD 1.3 binary compatibility 132options COMPAT_14 # NetBSD 1.4 binary compatibility 133options COMPAT_SUNOS # SunOS 4.x binary compatibility 134options COMPAT_SVR4 # SunOS 5.x binary compatibility 135#options COMPAT_NETBSD32 # NetBSD/sparc binary compatibility -- 64-bit only 136options EXEC_AOUT # execve(2) support for a.out binaries 137options EXEC_ELF32 # Exec module for SunOS 5.x binaries. 138#options EXEC_ELF64 # Exec module for sparc64 & SunOs 5.x binaries. -- 64-bit only 139#options SYSCALL_DEBUG 140 141## File systems. You probably need at least one of FFS or NFS. 142file-system FFS # Berkeley Fast Filesystem 143file-system NFS # Sun NFS-compatible filesystem client 144file-system KERNFS # kernel data-structure filesystem 145file-system NULLFS # NULL layered filesystem 146file-system OVERLAY # overlay file system 147file-system MFS # memory-based filesystem 148file-system FDESC # user file descriptor filesystem 149file-system UMAPFS # uid/gid remapping filesystem 150file-system LFS # Log-based filesystem (still experimental) 151file-system PORTAL # portal filesystem (still experimental) 152file-system PROCFS # /proc 153file-system CD9660 # ISO 9660 + Rock Ridge file system 154file-system UNION # union file system 155file-system MSDOSFS # MS-DOS FAT filesystem(s). 156 157## File system options. 158options NFSSERVER # Sun NFS-compatible filesystem server 159options QUOTA # FFS quotas 160#options FFS_EI # FFS Endian Independent support 161options SOFTDEP # FFS soft updates support. 162 163## Network protocol support. In most environments, INET is required. 164options INET # IP (Internet Protocol) v4 165options INET6 # IPV6 166options PULLDOWN_TEST # use m_pulldown for IPv4/v6 processing 167#options IPSEC # IP security 168#options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 169#options IPSEC_DEBUG # debug for IP security 170options TCP_COMPAT_42 # 4.2BSD IP implementation compatibility 171#options GATEWAY # packet forwarding ("router switch") 172options MROUTING # packet forwarding of multicast packets 173#options DIRECTED_BROADCAST # allow broadcasts through routers 174options NS # Xerox NS networking 175#options NSIP # Xerox NS tunneling over IP 176options ISO,TPIP # OSI networking 177#options EON # OSI tunneling over IP 178#options CCITT,LLC,HDLC # X.25 packet switched protocol 179options NETATALK # AppleTalk (over Ethernet) protocol 180options NTP # Network Time Protocol in-kernel support 181#options PPS_SYNC # Add serial line synchronization for NTP 182options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 183options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 184options PPP_BSDCOMP # Add BSD compression to ppp device 185options PPP_DEFLATE # Add deflate (libz) compression to ppp device 186options PPP_FILTER # Add active filters for ppp (via bpf) 187 188 189#### Main bus and CPU .. all systems. 190mainbus0 at root 191cpu0 at mainbus0 192 193#### Bus types found on SPARC systems. 194 195sbus0 at mainbus0 # Ultra 1 196#upa0 at mainbus0 # Ultra 1E, Ultra 2, Ex0000 197psycho0 at mainbus0 # Darwin, Ultra5 198psycho* at mainbus0 # U2P 199pci0 at psycho0 200pci* at psycho? 201pci* at simba? 202simba* at pci? dev ? function ? # `APB' support. 203ebus* at pci? # ebus devices 204 205# Ultra5/10/AXi 206simba0 at pci0 dev 1 function 0 207pci1 at simba0 208simba1 at pci0 dev 1 function 1 209pci2 at simba1 210 211#### Standard system devices -- all required for a given architecture 212 213## PROM console driver -- if all else fails 214pcons0 at mainbus0 # PROM console 215 216## Auxiliary system registers -- We use the OBP for power management 217auxio* at ebus? # auxio registers 218auxio* at sbus? slot ? offset ? # auxio registers 219 220# We also need: 221bpp* at sbus? slot ? offset ? # parallel port 222lpt* at ebus? # parallel port 223 224## Mostek clock found on 4/300, sun4c, sun4m and sun4u systems. 225## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 226clock* at sbus? slot ? offset ? 227clock* at ebus? 228 229## Timer chip found on 4/300, sun4c, sun4m and (some) sun4u systems. 230timer* at mainbus0 # sun4c 231 232#### Serial port configuration 233 234## Zilog 8530 serial chips. Each has two-channels. 235## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 236zs0 at sbus? slot ? offset ? 237zstty0 at zs0 channel 0 # ttya 238zstty1 at zs0 channel 1 # ttyb 239 240zs1 at sbus? slot ? offset ? 241kbd0 at zs1 channel 0 # keyboard 242ms0 at zs1 channel 1 # mouse 243 244## PCI machines have serial ports: 245## Siemens SAB82532 controller: ttya and ttyb (`su'; sab) 246## Part of NS PC87332VLJ Super I/O controller: kbd/mouse (`se'; com) 247 248## These are two SAB82532 controllers 249#sab0 at ebus? # ttya/ttyb 250#sabtty0 at sab0 channel 0 # ttya 251#sabtty1 at sab0 channel 1 # ttyb 252 253## Part of a PC87332VLJ? 254#ucom0 at ebus? addr 0x3083f8 # `com' driver 255#ucom1 at ebus? addr 0x3062f8 # 256#ucom0 at ebus? # `com' driver 257#ucom1 at ebus? # 258#kbd0 at ucom0 channel 0 # keyboard 259#ms0 at ucom1 channel 1 # mouse 260 261#### Disk controllers and disks 262 263## The following flags may be set for the NCR53c94 based esp driver: 264## bits 0-7: disable disconnect/reselect for the corresponding target 265## bits 8-15: disable synchronous negotiation for target [bit-8] 266 267## sun4u on-board SCSI, and FSBE/S SBus SCSI cards, an NCR53c94 or 268## equivalent behind an LSI Logic DMA controller 269 270dma* at sbus? slot ? offset ? # SBus 271esp* at dma? flags 0x0000 # SBus 272 273scsibus* at esp? 274 275## Qlogic ISP SBus SCSI Card 276isp* at sbus? slot ? offset ? 277scsibus* at isp? 278 279## FAS support missing 280#fas* at sbus? slot ? offset ? 281#scsibus* at fas? 282 283## GLM support missing 284siop* at pci? # 53C875 "glm" compatible 285scsibus* at siop? 286 287## Adaptec [23]94x, aic78x0 SCSI controller 288ahc* at pci? dev ? function ? 289scsibus* at ahc? 290 291## These entries find devices on all SCSI busses and assign 292## unit numbers dynamically. 293sd* at scsibus? target ? lun ? # SCSI disks 294st* at scsibus? target ? lun ? # SCSI tapes 295cd* at scsibus? target ? lun ? # SCSI CD-ROMs 296ch* at scsibus? target ? lun ? # SCSI changer devices 297ss* at scsibus? target ? lun ? # SCSI scanners 298uk* at scsibus? target ? lun ? # unknown SCSI 299 300# PCI IDE. 301pciide* at pci ? dev ? function ? flags 0x0000 302wd* at pciide? channel ? drive ? flags 0x0000 303atapibus* at pciide? channel ? 304 305cd* at atapibus? drive ? flags 0x0000 # ATAPI CD-ROM drives 306sd* at atapibus? drive ? flags 0x0000 # ATAPI disk drives 307uk* at atapibus? drive ? flags 0x0000 # ATAPI unknown 308 309## Floppy controller and drive found on SPARCstations. 310 311# need share with the sparc, and everyone else. needs to use auxio. 312# actually, the ebus version has (will have) direct access to it's AUXIO 313# register space (it is mapped in to fdthree not auxio). 314#fdc0 at sbus? slot ? offset ? # SUNW,fdtwo 315#fdc0 at ebus? # fdthree 316#fd* at fdc0 # the drive itself 317 318## A disk-like interface to files. Can be used to create floppy, CD, 319## miniroot images, etc. 320 321pseudo-device vnd 4 322 323## Concatenated and striped disks; with this, you can create a software-based 324## disk array similar to a "RAID 0" setup. See ccd(4). 325 326pseudo-device ccd 4 327 328## RAIDframe disk driver: software RAID driver. See raid(4). 329 330pseudo-device raid 4 331#options RAID_AUTOCONFIG # auto-configuration of RAID components 332 333## Memory disk device, used on boot floppies with compressed 334## kernel-plus-root-disk images. 335 336pseudo-device md 1 337 338 339#### Network interfaces 340 341## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 342## Three flavors of additional SBus ethernets are available. One attaches 343## directly like the sun4c on-board, one uses the ledma device like the 344## sun4m on-board, and one uses the lebuffer device. 345 346ledma0 at sbus? slot ? offset ? # sun4m on-board 347le0 at ledma0 # sun4m on-board 348le* at sbus? slot ? offset ? # SBus 349ledma* at sbus? slot ? offset ? # SBus 350le* at ledma? # SBus 351lebuffer0 at sbus? slot ? offset ? # SBus 352le0 at lebuffer? # SBus 353lebuffer* at sbus? slot ? offset ? # SBus 354le* at lebuffer? # SBus 355 356## Happy Meal Ethernet 357hme* at sbus? slot ? offset ? 358hme* at pci? dev ? function ? # network "hme" compatible 359hme0 at pci2 dev 1 function 1 # U5/U10 on-board 360 361# MII/PHY support 362# XXX: only nsphy "tested" 363exphy* at mii? phy ? # 3Com internal PHYs 364icsphy* at mii? phy ? # Integrated Circuit Systems ICS1890 365inphy* at mii? phy ? # Intel 82555 PHYs 366lxtphy* at mii? phy ? # Level One LXT-970 PHYs 367nsphy* at mii? phy ? # NS83840 PHYs 368qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 369sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 370tlphy* at mii? phy ? # ThunderLAN PHYs 371ukphy* at mii? phy ? # generic unknown PHYs 372 373## qec/be, qec/hme 374qec* at sbus? slot ? offset ? 375be* at qec? 376qe* at qec? 377 378## Loopback network interface; required 379pseudo-device loop 380 381## SLIP and CSLIP interfaces, for IP over a serial line. 382pseudo-device sl 2 383 384## PPP, the successor to SLIP. See pppd(8). 385pseudo-device ppp 2 386 387## Starmode Radio IP, a special hardware network device. 388pseudo-device strip 1 389 390## Network "tunnel" device, allowing protocol stacks to run in the userland. 391## This is used by the third-party user-mode "ppp" program, and others. 392pseudo-device tun 4 393 394## Generic L3 over IP tunnel 395#pseudo-device gre 2 # generic L3 over IP tunnel 396 397## Berkeley Packet Filter, required to run RARPD. A generic C-language 398## interface that allows selective examining of incoming packets. 399pseudo-device bpfilter 8 400 401## IP Filter, used in firewall and NAT applications. See ipnat(8) for 402## one example of the use of the IP Filter. 403pseudo-device ipfilter 404 405## for IPv6 406pseudo-device gif 4 # IPv[46] over IPv[46] tunnel (RFC1933) 407#pseudo-device faith 1 # IPv[46] tcp relay translation i/f 408#pseudo-device stf 1 # 6to4 IPv6 over IPv4 encapsulation 409 410 411#### Audio and video devices 412 413## /dev/audio support (`audiocs' plus `audio') 414## 415audiocs* at sbus? slot ? offset ? # SUNW,CS4231 416audio* at audiocs? 417 418 419## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 420## systems. If your sun4 system has a cgfour installed in the P4 slot, 421## the P4 entries for "bwtwo" will attach to the overlay plane of the 422## "cgfour". 423 424#bwtwo0 at sbus? slot ? offset ? # sun4c and sun4m 425#bwtwo* at sbus? slot ? offset ? # 426 427## Sun "cgthree" Sbus color framebuffer 428#cgthree0 at sbus? slot ? offset ? 429#cgthree* at sbus? slot ? offset ? 430 431## Sun "cgsix" accelerated color framebuffer. 432cgsix0 at sbus? slot ? offset ? 433cgsix* at sbus? slot ? offset ? 434 435## Sun "tcx" accelerated color framebuffer. 436#tcx0 at sbus? slot ? offset ? 437#tcx* at sbus? slot ? offset ? 438 439# Sun "cgfourteen" accelerated 24-bit framebuffer. 440#cgfourteen0 at obio0 # sun4m 441 442## Sun FFB not supported 443#ffb* at upa? 444 445#### Other device configuration 446 447## Pseudo ttys, required for network logins and programs like screen. 448## 32 is a good number for average systems; you may have as many as you 449## like, though 256 is more or less the upper limit. Increasing this 450## number still requires you to run /dev/MAKEDEV to create the files 451## for the ptys. 452 453pseudo-device pty 64 # pseudo-ttys (for network, etc.) 454 455## Random device, used to implement /dev/random (a source of random noise), 456## and generate randomness for some kernel formulae. 457## THIS DEVICE IS EXPERIMENTAL; use at your own risk. 458 459pseudo-device rnd 460