GENERIC32 revision 1.49
1# $NetBSD: GENERIC32,v 1.49 2002/10/04 21:11:27 martin Exp $ 2 3include "arch/sparc64/conf/std.sparc64" 4 5options INCLUDE_CONFIG_FILE # embed config file in kernel binary 6 7#ident "GENERIC-$Revision: 1.49 $" 8 9maxusers 64 10 11## System kernel configuration. See options(4) for more detail. 12 13 14# Options for variants of the Sun SPARC architecure. 15# We currently support three architecture types; at least one is required. 16options SUN4U # sun4u - UltraSPARC 17#options BLINK # blink the system LED 18 19## System options specific to the sparc machine type 20 21## Use a faster console than the PROM's slow drawing routines. Not needed 22## for headless (no framebuffer) machines. 23# XXX borken on sparc64 24#options RASTERCONSOLE # fast rasterop console 25#options FONT_GALLANT12x22 # the console font 26#options FONT_BOLD8x16 # a somewhat smaller font 27 28#### System options that are the same for all ports 29 30## Root device configuration: change the ?'s if you are going to use a 31## nonstandard root partition (other than where the kernel is booted from) 32## and/or nonstandard root type (not ffs or nfs). Normally this can be 33## automagically determined at boot time. 34 35config netbsd root on ? type ? 36 37## UVM options. 38#options UVM_PAGE_TRKOWN 39#options UVMHIST 40#options UVMHIST_PRINT # Loud! 41 42## System call tracing (see ktrace(1)). 43options KTRACE 44 45## Collect statistics on kernel malloc's and free's. This does have a 46## significant performance hit on slower machines, so it is intended for 47## diagnostic use only. 48#options KMEMSTATS 49 50## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 51options SYSVMSG # System V message queues 52options SYSVSEM # System V semaphores 53options SYSVSHM # System V shared memory 54#options SHMMAXPGS=1024 # 1024 pages is the default 55 56## Loadable kernel module support; still under development. 57options LKM 58 59options USERCONF # userconf(4) support 60#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 61 62## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 63options NFS_BOOT_BOOTPARAM 64#options NFS_BOOT_BOOTP 65options NFS_BOOT_DHCP 66 67#### Debugging options 68 69## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 70## serial console break or keyboard reset, where the PROM would normally 71## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 72# we enable DDB in GENERIC for now. 73options DDB # kernel dynamic debugger 74options DDB_HISTORY_SIZE=100 # enable history editing in DDB 75#options DDB_ONPANIC # see also sysctl(8): `ddb.onpanic' 76 77## You may also use gdb, on another computer connected to this machine over 78## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 79## KGDB_DEV is a dev_t encoded device number of the serial port to use. 80## (0xc01 = ttya, 0xc02 = ttyb.) 81#options KGDB # support for kernel gdb 82#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 83#options KGDB_DEVRATE=38400 # baud rate 84 85 86## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 87## such that gdb(1) can be used on a kernel coredump. 88 89#makeoptions DEBUG="-g" 90 91 92## Adds code to the kernel that does internal consistency checks, and will 93## cause the kernel to panic if corruption of internal data structures 94## is detected. 95#options DIAGNOSTIC # extra kernel sanity checking 96 97## Enable (possibly expensive) debugging code that may also display messages 98## on the system console 99#options DEBUG 100 101## Make SCSI error messages more verbose when explaining their meanings. 102options SCSIVERBOSE 103options PCIVERBOSE 104options MIIVERBOSE # verbose PHY autoconfig messages 105#options PCI_CONFIG_DUMP # verbosely dump PCI config space 106 107## `INSECURE' turns off the kernel security level (securelevel = 0 always). 108## This allows writing to /dev/mem, loading kernel modules while multi-user, 109## and other insecurities good only for development work. Do not use this 110## option on a production machine. 111#options INSECURE 112 113## Allow non-root users to grab /dev/console with programs such as xconsole. 114## `xconsole' therefore does not need setuid root with this option enabled. 115#options UCONSOLE 116 117## `FDSCRIPTS' allows non-readable but executable scripts by providing a 118## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 119## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 120## opaque file mechanism. Perl calls this "secure setuid scripts." 121 122#options FDSCRIPTS 123#options SETUIDSCRIPTS 124 125## Options for compatibility with previous releases foreign system binaries. 126## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 127## additional user-level utilities or system configuration files. See 128## compat_sunos(8) and compat_svr4(8). 129 130options COMPAT_43 # 4.3BSD system interfaces 131options COMPAT_09 # NetBSD 0.9 binary compatibility 132options COMPAT_10 # NetBSD 1.0 binary compatibility 133options COMPAT_11 # NetBSD 1.1 binary compatibility 134options COMPAT_12 # NetBSD 1.2 binary compatibility 135options COMPAT_13 # NetBSD 1.3 binary compatibility 136options COMPAT_14 # NetBSD 1.4 binary compatibility 137options COMPAT_SUNOS # SunOS 4.x binary compatibility 138options COMPAT_SVR4 # SunOS 5.x binary compatibility 139#options COMPAT_SVR4_32 # SunOS 5.x 32-bit binary compatibility -- 64-bit only 140#options COMPAT_NETBSD32 # NetBSD/sparc binary compatibility -- 64-bit only 141options EXEC_AOUT # execve(2) support for a.out binaries 142options EXEC_ELF32 # Exec module for SunOS 5.x binaries. 143#options SYSCALL_DEBUG 144 145#options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended. 146 147## File systems. You probably need at least one of FFS or NFS. 148file-system FFS # Berkeley Fast Filesystem 149file-system NFS # Sun NFS-compatible filesystem client 150file-system KERNFS # kernel data-structure filesystem 151file-system NULLFS # NULL layered filesystem 152file-system OVERLAY # overlay file system 153file-system MFS # memory-based filesystem 154file-system FDESC # user file descriptor filesystem 155file-system UMAPFS # uid/gid remapping filesystem 156file-system LFS # Log-based filesystem (still experimental) 157file-system PORTAL # portal filesystem (still experimental) 158file-system PROCFS # /proc 159file-system CD9660 # ISO 9660 + Rock Ridge file system 160file-system UNION # union file system 161file-system MSDOSFS # MS-DOS FAT filesystem(s). 162 163## File system options. 164options NFSSERVER # Sun NFS-compatible filesystem server 165options QUOTA # FFS quotas 166#options FFS_EI # FFS Endian Independent support 167options SOFTDEP # FFS soft updates support. 168 169## Network protocol support. In most environments, INET is required. 170options INET # IP (Internet Protocol) v4 171options INET6 # IPV6 172#options IPSEC # IP security 173#options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 174#options IPSEC_DEBUG # debug for IP security 175#options GATEWAY # packet forwarding ("router switch") 176options MROUTING # packet forwarding of multicast packets 177#options DIRECTED_BROADCAST # allow broadcasts through routers 178options NS # Xerox NS networking 179#options NSIP # Xerox NS tunneling over IP 180options ISO,TPIP # OSI networking 181options EON # OSI tunneling over IP 182#options CCITT,LLC,HDLC # X.25 packet switched protocol 183options NETATALK # AppleTalk (over Ethernet) protocol 184options NTP # Network Time Protocol in-kernel support 185#options PPS_SYNC # Add serial line synchronization for NTP 186options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 187options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 188#options IPFILTER_DEFAULT_BLOCK # block all packets by default 189options PPP_BSDCOMP # Add BSD compression to ppp device 190options PPP_DEFLATE # Add deflate (libz) compression to ppp device 191options PPP_FILTER # Add active filters for ppp (via bpf) 192#options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG 193 194 195#### Main bus and CPU .. all systems. 196mainbus0 at root 197cpu0 at mainbus0 198 199#### Bus types found on SPARC systems. 200 201sbus0 at mainbus0 # Ultra 1 202#upa0 at mainbus0 # Ultra 1E, Ultra 2, Ex0000 203psycho* at mainbus0 # Darwin, Ultra5 204pci* at psycho? 205pci* at ppb? 206ppb* at pci? # `APB' support. 207ebus* at pci? # ebus devices 208# XXX 'puc's aren't really bridges, but there's no better place for them here 209puc* at pci? dev ? function ? # PCI "universal" comm. cards 210 211#### Standard system devices -- all required for a given architecture 212 213## PROM console driver -- if all else fails 214pcons0 at mainbus0 # PROM console 215 216## Auxiliary system registers -- We use the OBP for power management 217auxio* at ebus? # auxio registers 218auxio* at sbus? slot ? offset ? # auxio registers 219 220# We also need: 221bpp* at sbus? slot ? offset ? # parallel port 222lpt* at ebus? # parallel port 223 224## Mostek clock found on 4/300, sun4c, sun4m and sun4u systems. 225## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 226clock* at sbus? slot ? offset ? 227clock* at ebus? 228rtc* at ebus? 229 230## Timer chip found on 4/300, sun4c, sun4m and (some) sun4u systems. 231timer* at mainbus0 # sun4c 232 233#### Serial port configuration 234 235## Zilog 8530 serial chips. Each has two-channels. 236## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 237zs* at sbus? slot ? offset ? 238zstty* at zs? channel ? # ttya 239kbd0 at zstty? 240ms0 at zstty? 241 242## PCI machines have serial ports: 243## Siemens SAB82532 controller: ttya and ttyb (`su'; sab) 244## Part of NS PC87332VLJ Super I/O controller: kbd/mouse (`se'; com) 245 246## The SAB82532 controller has two serial ports 247sab* at ebus? # ttya/ttyb 248sabtty* at sab? channel ? 249 250## Part of a PC87332VLJ 251com* at ebus? # `com' driver for `su' 252kbd0 at com? # keyboard 253ms0 at com? # mouse 254 255# PCI serial interfaces 256com* at puc? port ? # 16x50s on "universal" comm boards 257cy* at pci? dev ? function ? # Cyclades Cyclom-Y serial boards 258cz* at pci? dev ? function ? # Cyclades-Z multi-port serial boards 259 260#### Disk controllers and disks 261 262## The following flags may be set for the NCR53c94 based esp driver: 263## bits 0-7: disable disconnect/reselect for the corresponding target 264## bits 8-15: disable synchronous negotiation for target [bit-8] 265 266## sun4u on-board SCSI, and FSBE/S SBus SCSI cards, an NCR53c94 or 267## equivalent behind an LSI Logic DMA controller 268 269# XXX - the esp driver has problems with tagged queueing. 270# To avoid these, tagged queueing has been disabled for the first 8 targets 271# by setting those bits to 1 (starting at bit 16, see esp(4) for details). 272# If you want tagged queueing, and are sure it works for you, set the flags 273# value to 0. CAVEAT: using tagged queueing currently can cause data loss! 274 275dma* at sbus? slot ? offset ? # SBus 276esp* at dma? flags 0x00ff0000 # SBus 277 278esp* at sbus? slot ? offset ? flags 0x00ff0000 279isp* at sbus? slot ? offset ? 280isp* at pci? dev ? function ? # Qlogic ISP [12]0x0 SCSI/FibreChannel 281siop* at pci? # 53C875 "glm" compatible 282 283# PCI SCSI controllers 284# UT marks untested. 285adv* at pci? dev ? function ? # AdvanSys 1200[A,B], 9xx[U,UA] SCSI UT 286adw* at pci? dev ? function ? # AdvanSys 9x0UW[D], 3940U[2,3]W SCSI UT 287ahc* at pci? dev ? function ? # Adaptec [23]94x, aic78x0 SCSI UT 288bha* at pci? dev ? function ? # BusLogic 9xx SCSI UT 289dpt* at pci? dev ? function ? # DPT SmartCache/SmartRAID UT 290iha* at pci? dev ? function ? # Initio INIC-940/950 SCSI 291pcscp* at pci? dev ? function ? # AMD 53c974 PCscsi-PCI SCSI UT 292trm* at pci? dev ? function ? # Tekram DC-395U/UW/F, DC-315/U SCSI 293 294scsibus* at scsi? 295 296## These entries find devices on all SCSI busses and assign 297## unit numbers dynamically. 298sd* at scsibus? target ? lun ? # SCSI disks 299st* at scsibus? target ? lun ? # SCSI tapes 300cd* at scsibus? target ? lun ? # SCSI CD-ROMs 301ch* at scsibus? target ? lun ? # SCSI changer devices 302ss* at scsibus? target ? lun ? # SCSI scanners 303ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE devices 304uk* at scsibus? target ? lun ? # unknown SCSI 305 306# PCI IDE. 307pciide* at pci ? dev ? function ? flags 0x0000 308atapibus* at pciide? channel ? 309 310## Disable UDMA 4 which causes data corruption on the Acer Labs 311## chipset on Sun Blade 100 and Netra X1 machines. 312wd* at pciide? channel ? drive ? flags 0x0a00 # Disable UDMA 4 313 314 315cd* at atapibus? drive ? flags 0x0000 # ATAPI CD-ROM drives 316sd* at atapibus? drive ? flags 0x0000 # ATAPI disk drives 317uk* at atapibus? drive ? flags 0x0000 # ATAPI unknown 318 319# RAID controllers and devices (untested) 320cac* at pci? dev ? function ? # Compaq PCI array controllers 321mlx* at pci? dev ? function ? # Mylex DAC960 & DEC SWXCR family 322twe* at pci? dev ? function ? # 3ware Escalade RAID controllers 323 324ld* at cac? unit ? # logical disk devices 325ld* at twe? unit ? 326ld* at mlx? unit ? 327 328## Floppy controller and drive found on SPARCstations. 329 330# need share with the sparc, and everyone else. needs to use auxio. 331# actually, the ebus version has (will have) direct access to it's AUXIO 332# register space (it is mapped in to fdthree not auxio). 333#fdc0 at sbus? slot ? offset ? # SUNW,fdtwo 334#fdc0 at ebus? # fdthree 335#fd* at fdc0 # the drive itself 336 337## A disk-like interface to files. Can be used to create floppy, CD, 338## miniroot images, etc. 339 340pseudo-device vnd 4 341 342## Concatenated and striped disks; with this, you can create a software-based 343## disk array similar to a "RAID 0" setup. See ccd(4). 344 345pseudo-device ccd 4 346 347## RAIDframe disk driver: software RAID driver. See raid(4). 348 349pseudo-device raid 8 350options RAID_AUTOCONFIG # auto-configuration of RAID components 351# Options to enable various other RAIDframe RAID types. 352# options RF_INCLUDE_EVENODD=1 353# options RF_INCLUDE_RAID5_RS=1 354# options RF_INCLUDE_PARITYLOGGING=1 355# options RF_INCLUDE_CHAINDECLUSTER=1 356# options RF_INCLUDE_INTERDECLUSTER=1 357# options RF_INCLUDE_PARITY_DECLUSTERING=1 358# options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 359 360 361## Memory disk device, used on boot floppies with compressed 362## kernel-plus-root-disk images. 363 364pseudo-device md 1 365 366 367#### Network interfaces 368 369## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 370## Three flavors of additional SBus ethernets are available. One attaches 371## directly like the sun4c on-board, one uses the ledma device like the 372## sun4m on-board, and one uses the lebuffer device. 373 374ledma0 at sbus? slot ? offset ? # sun4m on-board 375le0 at ledma0 # sun4m on-board 376le* at sbus? slot ? offset ? # SBus 377ledma* at sbus? slot ? offset ? # SBus 378le* at ledma? # SBus 379lebuffer0 at sbus? slot ? offset ? # SBus 380le0 at lebuffer? # SBus 381lebuffer* at sbus? slot ? offset ? # SBus 382le* at lebuffer? # SBus 383 384## Happy Meal Ethernet 385hme* at sbus? slot ? offset ? 386hme* at pci? dev ? function ? # network "hme" compatible 387 388## qec/be, qec/hme 389qec* at sbus? slot ? offset ? 390be* at qec? 391qe* at qec? 392 393# PCI network interfaces 394# UT marks untested. 395an* at pci? dev ? function ? # Aironet PC4500/PC4800 (802.11) UT 396en* at pci? dev ? function ? # ENI/Adaptec ATM UT 397# XXX causes ICE 398#ep* at pci? dev ? function ? # 3Com 3c59x 399ex* at pci? dev ? function ? # 3Com 90x[B] UT 400epic* at pci? dev ? function ? # SMC EPIC/100 Ethernet UT 401esh* at pci? dev ? function ? # Essential HIPPI card UT 402fpa* at pci? dev ? function ? # DEC DEFPA FDDI UT 403fxp* at pci? dev ? function ? # Intel EtherExpress PRO 10+/100B UT 404gem* at pci? dev ? function ? # Apple GMAC and Sun ERI gigabit enet 405le* at pci? dev ? function ? # PCnet-PCI Ethernet UT 406# XXX uses vtophys() 407#lmc* at pci? dev ? function ? # Lan Media Corp SSI/HSSI/DS3 408ne* at pci? dev ? function ? # NE2000-compatible Ethernet UT 409ntwoc* at pci? dev ? function ? # Riscom/N2 PCI Sync Serial UT 410rtk* at pci? dev ? function ? # Realtek 8129/8139 UT 411sip* at pci? dev ? function ? # SiS 900 Ethernet UT 412ti* at pci? dev ? function ? # Alteon ACEnic gigabit Ethernet UT 413tl* at pci? dev ? function ? # ThunderLAN-based Ethernet 414tlp* at pci? dev ? function ? # DECchip 21x4x and clones 415vr* at pci? dev ? function ? # VIA Rhine Fast Ethernet 416 417# MII/PHY support 418# XXX: only nsphy "tested" 419dmphy* at mii? phy ? # Davicom DM9101 PHYs 420exphy* at mii? phy ? # 3Com internal PHYs 421icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 422inphy* at mii? phy ? # Intel 82555 PHYs 423iophy* at mii? phy ? # Intel 82553 PHYs 424lxtphy* at mii? phy ? # Level One LXT-970 PHYs 425nsphy* at mii? phy ? # NS83840 PHYs 426nsphyter* at mii? phy ? # NS83843 PHYs 427qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 428sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 429tlphy* at mii? phy ? # ThunderLAN PHYs 430tqphy* at mii? phy ? # TDK Semiconductor PHYs 431ukphy* at mii? phy ? # generic unknown PHYs 432 433# PCI USB controllers 434ohci* at pci? dev ? function ? # Open Host Controller 435 436usb* at ohci? # USB bus support 437uhub* at usb? # USB Hubs 438uhub* at uhub? port ? configuration ? interface ? 439 440uhidev* at uhub? port ? configuration ? interface ? # USB HID 441uhid* at uhidev? reportid ? # USB Generic HID 442 443ulpt* at uhub? port ? configuration ? interface ? # USB Printer 444 445umodem* at uhub? port ? configuration ? # USB Modem 446ucom* at umodem? 447 448umass* at uhub? port ? configuration ? interface ? # USB Mass Storage 449atapibus* at umass? channel ? 450scsibus* at umass? channel ? 451 452uaudio* at uhub? port ? configuration ? # USB audio 453 454# USB Ethernet adapters 455aue* at uhub? port ? # ADMtek AN986 Pegasus based adapters 456cue* at uhub? port ? # CATC USB-EL1201A based adapters 457kue* at uhub? port ? # Kawasaki LSI KL5KUSB101B based adapters 458 459uscanner* at uhub? port ? # USB scanners 460uyap* at uhub? port ? # Y@P firmware loader 461ugen* at uhub? port ? configuration ? interface ? # USB Generic driver 462 463# PCI IEEE1394 controllers 464fwohci* at pci? dev ? function ? # IEEE1394 Open Host Controller 465#fwlynx* at pci? dev ? function ? # IEEE1394 TI Lynx Controller 466fw* at fwbus? # IP over 1394 467 468# IEEE1394 nodes 469#fwnode* at fwbus? oui ? devhi ? devlo ? 470#scsibus* at fwnode? 471 472## Loopback network interface; required 473pseudo-device loop 474 475## SLIP and CSLIP interfaces, for IP over a serial line. 476pseudo-device sl 2 477 478## PPP, the successor to SLIP. See pppd(8). 479pseudo-device ppp 2 480 481## PPP over Ethernet (RFC 2516) 482pseudo-device pppoe 483 484## Starmode Radio IP, a special hardware network device. 485pseudo-device strip 1 486 487## Network "tunnel" device, allowing protocol stacks to run in the userland. 488## This is used by the third-party user-mode "ppp" program, and others. 489pseudo-device tun 4 490 491## Generic L3 over IP tunnel 492#pseudo-device gre 2 # generic L3 over IP tunnel 493 494## Berkeley Packet Filter, required to run RARPD. A generic C-language 495## interface that allows selective examining of incoming packets. 496pseudo-device bpfilter 8 497 498## Simple inter-network traffic bridging 499pseudo-device bridge 500 501## IP Filter, used in firewall and NAT applications. See ipnat(8) for 502## one example of the use of the IP Filter. 503pseudo-device ipfilter 504 505## for IPv6 506pseudo-device gif 4 # IPv[46] over IPv[46] tunnel (RFC1933) 507#pseudo-device faith 1 # IPv[46] tcp relay translation i/f 508#pseudo-device stf 1 # 6to4 IPv6 over IPv4 encapsulation 509 510 511#### Audio and video devices 512 513## /dev/audio support (`audiocs' plus `audio') 514## 515audiocs* at sbus? slot ? offset ? # SUNW,CS4231 516audiocs* at ebus? # SUNW,CS4231 in U5/U10 517autri* at pci? dev ? function ? # Blade 100 'sound' 518 519audio* at audiocs? 520audio* at autri? 521audio* at uaudio? 522 523#midi* at autri? 524 525 526## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 527## systems. If your sun4 system has a cgfour installed in the P4 slot, 528## the P4 entries for "bwtwo" will attach to the overlay plane of the 529## "cgfour". 530 531#bwtwo0 at sbus? slot ? offset ? # sun4c and sun4m 532#bwtwo* at sbus? slot ? offset ? 533 534## Sun "cgthree" Sbus color framebuffer 535#cgthree0 at sbus? slot ? offset ? 536#cgthree* at sbus? slot ? offset ? 537 538## Sun "cgsix" accelerated color framebuffer. 539cgsix0 at sbus? slot ? offset ? 540cgsix* at sbus? slot ? offset ? 541 542## Sun FFB not supported 543#ffb* at upa? 544 545#### Other device configuration 546 547## Pseudo ttys, required for network logins and programs like screen. 548 549pseudo-device pty # pseudo-ttys (for network, etc.) 550 551## Random device, used to implement /dev/random (a source of random noise), 552## and generate randomness for some kernel formulae. 553 554pseudo-device rnd 555 556pseudo-device clockctl # user control of clock subsystem 557