GENERIC32 revision 1.50
1# 	$NetBSD: GENERIC32,v 1.50 2002/10/12 19:57:44 provos Exp $
2
3include "arch/sparc64/conf/std.sparc64"
4
5options 	INCLUDE_CONFIG_FILE	# embed config file in kernel binary
6
7#ident 		"GENERIC-$Revision: 1.50 $"
8
9maxusers	64
10
11## System kernel configuration.  See options(4) for more detail.
12
13
14# Options for variants of the Sun SPARC architecure.
15# We currently support three architecture types; at least one is required.
16options 	SUN4U		# sun4u - UltraSPARC
17#options 	BLINK		# blink the system LED
18
19## System options specific to the sparc machine type
20
21## Use a faster console than the PROM's slow drawing routines.  Not needed
22## for headless (no framebuffer) machines.
23# XXX borken on sparc64
24#options 	RASTERCONSOLE		# fast rasterop console
25#options 	FONT_GALLANT12x22	# the console font
26#options 	FONT_BOLD8x16		# a somewhat smaller font
27
28#### System options that are the same for all ports
29
30## Root device configuration: change the ?'s if you are going to use a
31## nonstandard root partition (other than where the kernel is booted from)
32## and/or nonstandard root type (not ffs or nfs).  Normally this can be
33## automagically determined at boot time.
34
35config		netbsd	root on ? type ?
36
37## UVM options.
38#options 	UVM_PAGE_TRKOWN
39#options 	UVMHIST
40#options 	UVMHIST_PRINT	# Loud!
41
42## System call tracing (see ktrace(1)).
43options 	KTRACE
44options 	SYSTRACE		# system call vetting via systrace(1)
45
46## Collect statistics on kernel malloc's and free's.  This does have a
47## significant performance hit on slower machines, so it is intended for
48## diagnostic use only.
49#options 	KMEMSTATS
50
51## System V compatible IPC subsystem.  (msgctl(2), semctl(2), and shmctl(2))
52options 	SYSVMSG		# System V message queues
53options 	SYSVSEM		# System V semaphores
54options 	SYSVSHM		# System V shared memory
55#options 	SHMMAXPGS=1024	# 1024 pages is the default
56
57## Loadable kernel module support; still under development.
58options 	LKM
59
60options 	USERCONF	# userconf(4) support
61#options	PIPE_SOCKETPAIR	# smaller, but slower pipe(2)
62
63## NFS boot options; tries DHCP/BOOTP then BOOTPARAM
64options 	NFS_BOOT_BOOTPARAM
65#options 	NFS_BOOT_BOOTP
66options 	NFS_BOOT_DHCP
67
68#### Debugging options
69
70## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at
71## serial console break or keyboard reset, where the PROM would normally
72## intercept.  DDB_HISTORY_SIZE adds up/down arrow command history.
73# we enable DDB in GENERIC for now.
74options 	DDB			# kernel dynamic debugger
75options 	DDB_HISTORY_SIZE=100	# enable history editing in DDB
76#options 	DDB_ONPANIC		# see also sysctl(8): `ddb.onpanic'
77
78## You may also use gdb, on another computer connected to this machine over
79## a serial port.  Both KGDB_DEV and KGDB_DEVRATE should be specified;
80## KGDB_DEV is a dev_t encoded device number of the serial port to use.
81## (0xc01 = ttya, 0xc02 = ttyb.)
82#options 	KGDB			# support for kernel gdb
83#options 	KGDB_DEV=0xc01		# kgdb device number (this is `ttyb')
84#options 	KGDB_DEVRATE=38400	# baud rate
85
86
87## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file),
88## such that gdb(1) can be used on a kernel coredump.
89
90#makeoptions	DEBUG="-g"
91
92
93## Adds code to the kernel that does internal consistency checks, and will
94## cause the kernel to panic if corruption of internal data structures
95## is detected.
96#options 	DIAGNOSTIC	# extra kernel sanity checking
97
98## Enable (possibly expensive) debugging code that may also display messages
99## on the system console
100#options 	DEBUG
101
102## Make SCSI error messages more verbose when explaining their meanings.
103options 	SCSIVERBOSE
104options 	PCIVERBOSE
105options 	MIIVERBOSE	# verbose PHY autoconfig messages
106#options 	PCI_CONFIG_DUMP	# verbosely dump PCI config space
107
108## `INSECURE' turns off the kernel security level (securelevel = 0 always).
109## This allows writing to /dev/mem, loading kernel modules while multi-user,
110## and other insecurities good only for development work.  Do not use this
111## option on a production machine.
112#options 	INSECURE
113
114## Allow non-root users to grab /dev/console with programs such as xconsole.
115## `xconsole' therefore does not need setuid root with this option enabled.
116#options 	UCONSOLE
117
118## `FDSCRIPTS' allows non-readable but executable scripts by providing a
119## pre-opened opaque file to the script interpreter.  `SETUIDSCRIPTS',
120## which implies FDSCRIPTS, allows scripts to be set-user-id using the same
121## opaque file mechanism.  Perl calls this "secure setuid scripts."
122
123#options 	FDSCRIPTS
124#options 	SETUIDSCRIPTS
125
126## Options for compatibility with previous releases foreign system binaries.
127## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up
128## additional user-level utilities or system configuration files. See
129## compat_sunos(8) and compat_svr4(8).
130
131options 	COMPAT_43	# 4.3BSD system interfaces
132options 	COMPAT_09	# NetBSD 0.9 binary compatibility
133options 	COMPAT_10	# NetBSD 1.0 binary compatibility
134options 	COMPAT_11	# NetBSD 1.1 binary compatibility
135options 	COMPAT_12	# NetBSD 1.2 binary compatibility
136options 	COMPAT_13	# NetBSD 1.3 binary compatibility
137options 	COMPAT_14	# NetBSD 1.4 binary compatibility
138options 	COMPAT_SUNOS	# SunOS 4.x binary compatibility
139options 	COMPAT_SVR4	# SunOS 5.x binary compatibility
140#options 	COMPAT_SVR4_32	# SunOS 5.x 32-bit binary compatibility -- 64-bit only
141#options 	COMPAT_NETBSD32	# NetBSD/sparc binary compatibility -- 64-bit only
142options 	EXEC_AOUT	# execve(2) support for a.out binaries
143options 	EXEC_ELF32	# Exec module for SunOS 5.x binaries.
144#options 	SYSCALL_DEBUG
145
146#options 	TCP_COMPAT_42	# 4.2BSD TCP/IP bug compat. Not recommended.
147
148## File systems.  You probably need at least one of FFS or NFS.
149file-system	FFS		# Berkeley Fast Filesystem
150file-system	NFS		# Sun NFS-compatible filesystem client
151file-system	KERNFS		# kernel data-structure filesystem
152file-system	NULLFS		# NULL layered filesystem
153file-system 	OVERLAY		# overlay file system
154file-system	MFS		# memory-based filesystem
155file-system	FDESC		# user file descriptor filesystem
156file-system	UMAPFS		# uid/gid remapping filesystem
157file-system	LFS		# Log-based filesystem (still experimental)
158file-system	PORTAL		# portal filesystem (still experimental)
159file-system	PROCFS		# /proc
160file-system	CD9660		# ISO 9660 + Rock Ridge file system
161file-system	UNION		# union file system
162file-system	MSDOSFS		# MS-DOS FAT filesystem(s).
163
164## File system options.
165options 	NFSSERVER	# Sun NFS-compatible filesystem server
166options 	QUOTA		# FFS quotas
167#options 	FFS_EI		# FFS Endian Independent support
168options 	SOFTDEP		# FFS soft updates support.
169
170## Network protocol support.  In most environments, INET is required.
171options 	INET		# IP (Internet Protocol) v4
172options 	INET6		# IPV6
173#options 	IPSEC		# IP security
174#options 	IPSEC_ESP	# IP security (encryption part; define w/IPSEC)
175#options 	IPSEC_DEBUG	# debug for IP security
176#options 	GATEWAY		# packet forwarding ("router switch")
177options 	MROUTING	# packet forwarding of multicast packets
178#options 	DIRECTED_BROADCAST	# allow broadcasts through routers
179options 	NS		# Xerox NS networking
180#options 	NSIP		# Xerox NS tunneling over IP
181options 	ISO,TPIP	# OSI networking
182options 	EON		# OSI tunneling over IP
183#options 	CCITT,LLC,HDLC	# X.25 packet switched protocol
184options 	NETATALK	# AppleTalk (over Ethernet) protocol
185options 	NTP		# Network Time Protocol in-kernel support
186#options 	PPS_SYNC	# Add serial line synchronization for NTP
187options 	PFIL_HOOKS	# Add pfil(9) hooks, intended for custom LKMs.
188options 	IPFILTER_LOG	# Add ipmon(8) logging for ipfilter device
189#options 	IPFILTER_DEFAULT_BLOCK	# block all packets by default
190options 	PPP_BSDCOMP	# Add BSD compression to ppp device
191options 	PPP_DEFLATE	# Add deflate (libz) compression to ppp device
192options 	PPP_FILTER	# Add active filters for ppp (via bpf)
193#options 	TCP_DEBUG	# Record last TCP_NDEBUG packets with SO_DEBUG
194
195
196#### Main bus and CPU .. all systems.
197mainbus0 at root
198cpu0	at mainbus0
199
200#### Bus types found on SPARC systems.
201
202sbus0	at mainbus0				# Ultra 1
203#upa0	at mainbus0				# Ultra 1E, Ultra 2, Ex0000
204psycho*	at mainbus0				# Darwin, Ultra5
205pci*	at psycho?
206pci*	at ppb?
207ppb*	at pci?					# `APB' support.
208ebus*	at pci?					# ebus devices
209# XXX 'puc's aren't really bridges, but there's no better place for them here
210puc*	at pci? dev ? function ?		# PCI "universal" comm. cards
211
212#### Standard system devices -- all required for a given architecture
213
214## PROM console driver -- if all else fails
215pcons0	at mainbus0				# PROM console
216
217## Auxiliary system registers -- We use the OBP for power management
218auxio*	at ebus?				# auxio registers
219auxio*	at sbus? slot ? offset ?		# auxio registers
220
221# We also need:
222bpp*	at sbus? slot ? offset ?		# parallel port
223lpt*	at ebus?				# parallel port
224
225## Mostek clock found on 4/300, sun4c, sun4m and sun4u systems.
226## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems.
227clock*	at sbus? slot ? offset ?
228clock*	at ebus?
229rtc*	at ebus?
230
231## Timer chip found on 4/300, sun4c, sun4m and (some) sun4u systems.
232timer*	at mainbus0				# sun4c
233
234#### Serial port configuration
235
236## Zilog 8530 serial chips.  Each has two-channels.
237## zs0 is ttya and ttyb.  zs1 is the keyboard and mouse.
238zs*	at sbus? slot ? offset ?
239zstty*	at zs? channel ?			# ttya
240kbd0	at zstty?
241ms0	at zstty?
242
243## PCI machines have serial ports:
244##	Siemens SAB82532 controller: ttya and ttyb (`su'; sab)
245##	Part of NS PC87332VLJ Super I/O controller: kbd/mouse (`se'; com)
246
247## The SAB82532 controller has two serial ports
248sab*	at ebus?				# ttya/ttyb
249sabtty*	at sab? channel ?
250
251## Part of a PC87332VLJ
252com*	at ebus?				# `com' driver for `su'
253kbd0	at com?					# keyboard
254ms0	at com?					# mouse
255
256# PCI serial interfaces
257com*	at puc? port ?			# 16x50s on "universal" comm boards
258cy*	at pci? dev ? function ?	# Cyclades Cyclom-Y serial boards
259cz*	at pci? dev ? function ?	# Cyclades-Z multi-port serial boards
260
261#### Disk controllers and disks
262
263## The following flags may be set for the NCR53c94 based esp driver:
264##	bits 0-7:  disable disconnect/reselect for the corresponding target
265##	bits 8-15: disable synchronous negotiation for target [bit-8]
266
267## sun4u on-board SCSI, and FSBE/S SBus SCSI cards, an NCR53c94 or
268## equivalent behind an LSI Logic DMA controller
269
270# XXX - the esp driver has problems with tagged queueing.
271# To avoid these, tagged queueing has been disabled for the first 8 targets
272# by setting those bits to 1 (starting at bit 16, see esp(4) for details).
273# If you want tagged queueing, and are sure it works for you, set the flags
274# value to 0. CAVEAT: using tagged queueing currently can cause data loss!
275
276dma*	at sbus? slot ? offset ?		# SBus
277esp*	at dma? flags 0x00ff0000		# SBus
278
279esp*	at sbus? slot ? offset ? flags 0x00ff0000
280isp*	at sbus? slot ? offset ?
281isp*	at pci? dev ? function ?	# Qlogic ISP [12]0x0 SCSI/FibreChannel
282siop*	at pci? 			# 53C875 "glm" compatible
283
284# PCI SCSI controllers
285# 	UT marks untested.
286adv*	at pci? dev ? function ?	# AdvanSys 1200[A,B], 9xx[U,UA] SCSI UT
287adw*	at pci? dev ? function ?	# AdvanSys 9x0UW[D], 3940U[2,3]W SCSI UT
288ahc*	at pci? dev ? function ?	# Adaptec [23]94x, aic78x0 SCSI UT
289bha*	at pci? dev ? function ?	# BusLogic 9xx SCSI UT
290dpt*	at pci? dev ? function ?	# DPT SmartCache/SmartRAID UT
291iha*	at pci? dev ? function ?	# Initio INIC-940/950 SCSI
292pcscp*	at pci? dev ? function ?	# AMD 53c974 PCscsi-PCI SCSI UT
293trm*	at pci? dev ? function ?	# Tekram DC-395U/UW/F, DC-315/U SCSI
294
295scsibus* at scsi?
296
297## These entries find devices on all SCSI busses and assign
298## unit numbers dynamically.
299sd*	at scsibus? target ? lun ?		# SCSI disks
300st*	at scsibus? target ? lun ?		# SCSI tapes
301cd*	at scsibus? target ? lun ?		# SCSI CD-ROMs
302ch*	at scsibus? target ? lun ?		# SCSI changer devices
303ss*	at scsibus? target ? lun ?		# SCSI scanners
304ses*	at scsibus? target ? lun ?		# SCSI SES/SAF-TE devices
305uk*	at scsibus? target ? lun ?		# unknown SCSI
306
307# PCI IDE.
308pciide* at pci ? dev ? function ? flags 0x0000
309atapibus* at pciide? channel ?
310
311## Disable UDMA 4 which causes data corruption on the Acer Labs
312## chipset on Sun Blade 100 and Netra X1 machines.
313wd*	at pciide? channel ? drive ? flags 0x0a00 # Disable UDMA 4
314
315
316cd*	at atapibus? drive ? flags 0x0000	# ATAPI CD-ROM drives
317sd*	at atapibus? drive ? flags 0x0000	# ATAPI disk drives
318uk*	at atapibus? drive ? flags 0x0000	# ATAPI unknown
319
320# RAID controllers and devices (untested)
321cac*	at pci? dev ? function ?	# Compaq PCI array controllers
322mlx*	at pci? dev ? function ?	# Mylex DAC960 & DEC SWXCR family
323twe*	at pci? dev ? function ?	# 3ware Escalade RAID controllers
324
325ld*	at cac? unit ?			# logical disk devices
326ld*	at twe? unit ?
327ld*	at mlx? unit ?
328
329## Floppy controller and drive found on SPARCstations.
330
331# need share with the sparc, and everyone else.  needs to use auxio.
332# actually, the ebus version has (will have) direct access to it's AUXIO
333# register space (it is mapped in to fdthree not auxio).
334#fdc0	at sbus? slot ? offset ?		# SUNW,fdtwo
335#fdc0	at ebus?				# fdthree
336#fd*	at fdc0 	 			# the drive itself
337
338## A disk-like interface to files.  Can be used to create floppy, CD,
339## miniroot images, etc.
340
341pseudo-device	vnd	4
342
343## Concatenated and striped disks; with this, you can create a software-based
344## disk array similar to a "RAID 0" setup.  See ccd(4).
345
346pseudo-device	ccd	4
347
348## RAIDframe disk driver: software RAID driver.  See raid(4).
349
350pseudo-device	raid	8
351options 	RAID_AUTOCONFIG		# auto-configuration of RAID components
352# Options to enable various other RAIDframe RAID types.
353# options	RF_INCLUDE_EVENODD=1
354# options	RF_INCLUDE_RAID5_RS=1
355# options	RF_INCLUDE_PARITYLOGGING=1
356# options	RF_INCLUDE_CHAINDECLUSTER=1
357# options	RF_INCLUDE_INTERDECLUSTER=1
358# options 	RF_INCLUDE_PARITY_DECLUSTERING=1
359# options	RF_INCLUDE_PARITY_DECLUSTERING_DS=1
360
361
362## Memory disk device, used on boot floppies with compressed
363## kernel-plus-root-disk images.
364
365pseudo-device	md	1
366
367
368#### Network interfaces
369
370## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue
371## Three flavors of additional SBus ethernets are available.  One attaches
372## directly like the sun4c on-board, one uses the ledma device like the
373## sun4m on-board, and one uses the lebuffer device.
374
375ledma0		at sbus? slot ? offset ?	# sun4m on-board
376le0		at ledma0			# sun4m on-board
377le*		at sbus? slot ? offset ?	# SBus
378ledma*		at sbus? slot ? offset ?	# SBus
379le*		at ledma?			# SBus
380lebuffer0	at sbus? slot ? offset ?	# SBus
381le0		at lebuffer?			# SBus
382lebuffer*	at sbus? slot ? offset ?	# SBus
383le*		at lebuffer?			# SBus
384
385## Happy Meal Ethernet
386hme*		at sbus? slot ? offset ?
387hme*		at pci?	dev ? function ?	# network "hme" compatible
388
389## qec/be, qec/hme
390qec*		at sbus? slot ? offset ?
391be*		at qec?
392qe*		at qec?
393
394# PCI network interfaces
395# 	UT marks untested.
396an*	at pci? dev ? function ?	# Aironet PC4500/PC4800 (802.11) UT
397en*	at pci? dev ? function ?	# ENI/Adaptec ATM UT
398# XXX causes ICE
399#ep*	at pci? dev ? function ?	# 3Com 3c59x
400ex*	at pci? dev ? function ?	# 3Com 90x[B] UT
401epic*	at pci? dev ? function ?	# SMC EPIC/100 Ethernet UT
402esh*	at pci? dev ? function ?	# Essential HIPPI card UT
403fpa*	at pci? dev ? function ?	# DEC DEFPA FDDI UT
404fxp*	at pci? dev ? function ?	# Intel EtherExpress PRO 10+/100B UT
405gem*	at pci? dev ? function ?	# Apple GMAC and Sun ERI gigabit enet
406le*	at pci? dev ? function ?	# PCnet-PCI Ethernet UT
407# XXX uses vtophys()
408#lmc*	at pci? dev ? function ?	# Lan Media Corp SSI/HSSI/DS3
409ne*	at pci? dev ? function ?	# NE2000-compatible Ethernet UT
410ntwoc*	at pci? dev ? function ?	# Riscom/N2 PCI Sync Serial UT
411rtk*	at pci? dev ? function ?	# Realtek 8129/8139 UT
412sip*	at pci? dev ? function ?	# SiS 900 Ethernet UT
413ti*	at pci? dev ? function ?	# Alteon ACEnic gigabit Ethernet UT
414tl*	at pci? dev ? function ?	# ThunderLAN-based Ethernet
415tlp*	at pci? dev ? function ?	# DECchip 21x4x and clones
416vr*	at pci? dev ? function ?	# VIA Rhine Fast Ethernet
417
418# MII/PHY support
419# XXX: only nsphy "tested"
420dmphy*	at mii? phy ?			# Davicom DM9101 PHYs
421exphy*	at mii? phy ?			# 3Com internal PHYs
422icsphy*	at mii? phy ?			# Integrated Circuit Systems ICS189x
423inphy*	at mii? phy ?			# Intel 82555 PHYs
424iophy*	at mii? phy ?			# Intel 82553 PHYs
425lxtphy*	at mii? phy ?			# Level One LXT-970 PHYs
426nsphy*	at mii? phy ?			# NS83840 PHYs
427nsphyter* at mii? phy ?			# NS83843 PHYs
428qsphy*	at mii? phy ?			# Quality Semiconductor QS6612 PHYs
429sqphy*	at mii? phy ?			# Seeq 80220/80221/80223 PHYs
430tlphy*	at mii? phy ?			# ThunderLAN PHYs
431tqphy*	at mii? phy ?			# TDK Semiconductor PHYs
432ukphy*	at mii? phy ?			# generic unknown PHYs
433
434# PCI USB controllers
435ohci*	at pci? dev ? function ?			# Open Host Controller
436
437usb*	at ohci?					# USB bus support
438uhub*	at usb?						# USB Hubs
439uhub*	at uhub? port ? configuration ? interface ?
440
441uhidev*	at uhub? port ? configuration ? interface ?	# USB HID
442uhid*	at uhidev? reportid ?				# USB Generic HID
443
444ulpt*	at uhub? port ? configuration ? interface ?	# USB Printer
445
446umodem*	at uhub? port ? configuration ?			# USB Modem
447ucom*	at umodem?
448
449umass*	at uhub? port ? configuration ? interface ?	# USB Mass Storage
450atapibus* at umass? channel ?
451scsibus* at umass? channel ?
452
453uaudio*	at uhub? port ? configuration ?			# USB audio
454
455# USB Ethernet adapters
456aue*	at uhub? port ?		# ADMtek AN986 Pegasus based adapters
457cue*	at uhub? port ?		# CATC USB-EL1201A based adapters
458kue*	at uhub? port ?		# Kawasaki LSI KL5KUSB101B based adapters
459
460uscanner* at uhub? port ?				# USB scanners
461uyap* at uhub? port ?					# Y@P firmware loader
462ugen*	at uhub? port ? configuration ? interface ?	# USB Generic driver
463
464# PCI IEEE1394 controllers
465fwohci*	at pci? dev ? function ?	# IEEE1394 Open Host Controller
466#fwlynx* at pci? dev ? function ?	# IEEE1394 TI Lynx Controller
467fw*	at fwbus?			# IP over 1394
468
469# IEEE1394 nodes
470#fwnode* at fwbus? oui ? devhi ? devlo ?
471#scsibus* at fwnode?
472
473## Loopback network interface; required
474pseudo-device	loop
475
476## SLIP and CSLIP interfaces, for IP over a serial line.
477pseudo-device	sl		2
478
479## PPP, the successor to SLIP.  See pppd(8).
480pseudo-device	ppp		2
481
482## PPP over Ethernet (RFC 2516)
483pseudo-device	pppoe
484
485## Starmode Radio IP, a special hardware network device.
486pseudo-device	strip		1
487
488## Network "tunnel" device, allowing protocol stacks to run in the userland.
489## This is used by the third-party user-mode "ppp" program, and others.
490pseudo-device	tun		4
491
492## Generic L3 over IP tunnel
493#pseudo-device	gre		2	# generic L3 over IP tunnel
494
495## Berkeley Packet Filter, required to run RARPD.  A generic C-language
496## interface that allows selective examining of incoming packets.
497pseudo-device	bpfilter	8
498
499## Simple inter-network traffic bridging
500pseudo-device	bridge
501
502## IP Filter, used in firewall and NAT applications.  See ipnat(8) for
503## one example of the use of the IP Filter.
504pseudo-device	ipfilter
505
506## for IPv6
507pseudo-device	gif		4	# IPv[46] over IPv[46] tunnel (RFC1933)
508#pseudo-device	faith		1	# IPv[46] tcp relay translation i/f
509#pseudo-device	stf		1	# 6to4 IPv6 over IPv4 encapsulation
510
511
512#### Audio and video devices
513
514## /dev/audio support (`audiocs' plus `audio')
515##
516audiocs*	at sbus? slot ? offset ?	# SUNW,CS4231
517audiocs*	at ebus?			# SUNW,CS4231 in U5/U10
518autri*		at pci? dev ? function ?	# Blade 100 'sound'
519
520audio*		at audiocs?
521audio*		at autri?
522audio*		at uaudio?
523
524#midi*		at autri?
525
526
527## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m
528## systems.  If your sun4 system has a cgfour installed in the P4 slot,
529## the P4 entries for "bwtwo" will attach to the overlay plane of the
530## "cgfour".
531
532#bwtwo0		at sbus? slot ? offset ?	# sun4c and sun4m
533#bwtwo*		at sbus? slot ? offset ?
534
535## Sun "cgthree" Sbus color framebuffer
536#cgthree0	at sbus? slot ? offset ?
537#cgthree*	at sbus? slot ? offset ?
538
539## Sun "cgsix" accelerated color framebuffer.
540cgsix0		at sbus? slot ? offset ?
541cgsix*		at sbus? slot ? offset ?
542
543## Sun FFB not supported
544#ffb*		at upa?
545
546#### Other device configuration
547
548## Pseudo ttys, required for network logins and programs like screen.
549
550pseudo-device	pty			# pseudo-ttys (for network, etc.)
551
552## Random device, used to implement /dev/random (a source of random noise),
553## and generate randomness for some kernel formulae.
554
555pseudo-device	rnd
556
557pseudo-device	clockctl		# user control of clock subsystem
558