GENERIC revision 1.11
1# 	$NetBSD: GENERIC,v 1.11 1999/01/23 19:09:00 eeh Exp $
2
3include "arch/sparc64/conf/std.sparc64"
4
5maxusers	32
6
7## System kernel configuration.  See options(4) for more detail.
8
9
10# Options for variants of the Sun SPARC architecure.
11# We currently support three architecture types; at least one is required.
12options		SUN4U		# sun4u - Ultra 140 and 170
13options		TRAPWIN
14options		__ELF__		# we use elf 
15#options		_LP64		# we're using a 64-bit compiler
16
17## System options specific to the sparc machine type
18
19## Use a faster console than the PROM's slow drawing routines.  Not needed
20## for headless (no framebuffer) machines.
21# XXX broken on sparc64
22#options 	RASTERCONSOLE	# fast rasterop console
23
24
25#### System options that are the same for all ports
26
27## Root device configuration: change the ?'s if you are going to use a
28## nonstandard root partition (other than where the kernel is booted from)
29## and/or nonstandard root type (not ffs or nfs).  Normally this can be
30## automagically determined at boot time.
31
32config		netbsd	root on ? type ?
33
34## UVM options.
35#options	UVM_PAGE_TRKOWN
36#options 	UVMHIST
37#options 	UVMHIST_PRINT	# Loud!
38options 	PMAP_NEW
39
40## System call tracing (see ktrace(1)).
41options 	KTRACE
42
43## Collect statistics on kernel malloc's and free's.  This does have a
44## significant performance hit on slower machines, so it is intended for
45## diagnostic use only.
46#options 	KMEMSTATS
47
48## System V compatible IPC subsystem.  (msgctl(2), semctl(2), and shmctl(2))
49options 	SYSVMSG		# System V message queues
50options 	SYSVSEM		# System V semaphores
51options 	SYSVSHM		# System V shared memory
52#options 	SHMMAXPGS=1024	# 1024 pages is the default
53
54## Loadable kernel module support; still under development.
55options 	LKM
56
57## NFS boot options; default on sparc is the bootparam protocol
58options 	NFS_BOOT_BOOTPARAM
59#options 	NFS_BOOT_BOOTP
60#options 	NFS_BOOT_DHCP
61
62#### Debugging options
63
64## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at
65## serial console break or keyboard reset, where the PROM would normally
66## intercept.  DDB_HISTORY_SIZE adds up/down arrow command history.
67# we enable DDB in GENERIC for now.
68options 	DDB			# kernel dynamic debugger
69#options 	DDB_HISTORY_SIZE=100	# enable history editing in DDB
70#options 	DDB_ONPANIC		# see also sysctl(8): `ddb.onpanic'
71
72## You may also use gdb, on another computer connected to this machine over
73## a serial port.  Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is
74## a dev_t encoded device number of the serial port to use.
75## (0xc01 = ttya, 0xc02 = ttyb.)
76#options 	KGDB		# support for kernel gdb
77#options 	KGDBDEV=0xc01	# kgdb device number (this sample is `ttyb')
78#options 	KGDBRATE=38400	# baud rate
79
80
81## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file),
82## such that gdb(1) can be used on a kernel coredump.
83
84#makeoptions 	DEBUG="-g"
85
86
87## Adds code to the kernel that does internal consistency checks, and will
88## cause the kernel to panic if corruption of internal data structures
89## is detected.
90#options 	DIAGNOSTIC	# extra kernel sanity checking
91
92## Enable (possibly expensive) debugging code that may also display messages
93## on the system console
94#options 	DEBUG
95
96## Make SCSI error messages more verbose when explaining their meanings.
97options 	SCSIVERBOSE
98
99## `INSECURE' turns off the kernel security level (securelevel = 0 always).
100## This allows writing to /dev/mem, loading kernel modules while multi-user,
101## and other insecurities good only for development work.  Do not use this
102## option on a production machine.
103#options 	INSECURE
104
105## Allow non-root users to grab /dev/console with programs such as xconsole.
106## `xconsole' therefore does not need setuid root with this option enabled.
107#options 	UCONSOLE
108
109## `FDSCRIPTS' allows non-readable but executable scripts by providing a
110## pre-opened opaque file to the script interpreter.  `SETUIDSCRIPTS',
111## which implies FDSCRIPTS, allows scripts to be set-user-id using the same
112## opaque file mechanism.  Perl calls this "secure setuid scripts."
113
114#options 	FDSCRIPTS
115#options 	SETUIDSCRIPTS
116
117## Options for compatibility with previous releases foreign system binaries.
118## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up
119## additional user-level utilities or system configuration files. See
120## compat_sunos(8) and compat_svr4(8).
121
122options 	COMPAT_43	# 4.3BSD system interfaces
123options 	COMPAT_10	# NetBSD 1.0 binary compatibility
124options 	COMPAT_11	# NetBSD 1.1 binary compatibility
125options 	COMPAT_12	# NetBSD 1.2 binary compatibility
126options 	COMPAT_13	# NetBSD 1.3 binary compatibility
127#options 	COMPAT_SPARC32	# NetBSD/sparc binary compatibility -- 64-bit only
128options 	COMPAT_SUNOS	# SunOS 4.x binary compatibility
129options 	COMPAT_SVR4	# SunOS 5.x binary compatibility
130options 	EXEC_ELF32	# Exec module for SunOS 5.x binaries.
131#options		EXEC_ELF64	# Exec module for sparc64 & SunOs 5.x binaries. -- 64-bit only
132#options		SYSCALL_DEBUG
133
134## File systems.  You probably need at least one of FFS or NFS.
135file-system	FFS		# Berkeley Fast Filesystem
136file-system	NFS		# Sun NFS-compatible filesystem client
137file-system	KERNFS		# kernel data-structure filesystem
138file-system	NULLFS		# NULL layered filesystem
139file-system	MFS		# memory-based filesystem
140file-system	FDESC		# user file descriptor filesystem
141file-system	UMAPFS		# uid/gid remapping filesystem
142file-system	LFS		# Log-based filesystem (still experimental)
143file-system	PORTAL		# portal filesystem (still experimental)
144file-system	PROCFS		# /proc
145file-system	CD9660		# ISO 9660 + Rock Ridge file system
146file-system	UNION		# union file system
147file-system	MSDOSFS		# MS-DOS FAT filesystem(s).
148
149## File system options.
150options 	NFSSERVER	# Sun NFS-compatible filesystem server
151options 	QUOTA		# FFS quotas
152#options 	FFS_EI		# FFS Endian Independent support
153
154## Network protocol support.  In most environments, INET is required.
155options 	INET		# IP (Internet Protocol) v4
156options 	TCP_COMPAT_42	# 4.2BSD IP implementation compatibility
157#options 	GATEWAY		# packet forwarding ("router switch")
158options 	MROUTING	# packet forwarding of multicast packets
159#options 	DIRECTED_BROADCAST	# allow broadcasts through routers
160options 	NS		# Xerox NS networking
161#options 	NSIP		# Xerox NS tunneling over IP
162options 	ISO,TPIP	# OSI networking
163options 	EON		# OSI tunneling over IP
164#options 	CCITT,LLC,HDLC	# X.25 packet switched protocol
165options 	NETATALK	# AppleTalk (over Ethernet) protocol
166options 	NTP		# Network Time Protocol in-kernel support
167#options 	PPS_SYNC	# Add serial line synchronization for NTP
168options 	PFIL_HOOKS	# Add pfil(9) hooks, intended for custom LKMs.
169options 	IPFILTER_LOG	# Add ipmon(8) logging for ipfilter device
170options 	PPP_BSDCOMP	# Add BSD compression to ppp device
171options 	PPP_DEFLATE	# Add deflate (libz) compression to ppp device
172options 	PPP_FILTER	# Add active filters for ppp (via bpf)
173
174
175#### Main bus and CPU .. all systems.
176mainbus0 at root
177cpu0	at mainbus0
178
179#### Bus types found on SPARC systems.
180
181sbus0	at mainbus0				# Ultra 1
182#upa0	at mainbus0				# Ultra 1E, Ultra 2, Ex0000
183#pci0	at mainbus0				# Darwin
184#ebus*	at pci?					# ebus devices
185
186#### Standard system devices -- all required for a given architecture
187
188## Auxiliary system registers -- We use the OBP for power management
189#auxreg0 at sbus0
190#auxreg0 at pci0
191
192# We also need:
193# bpp0 at sbus0					# parallel port
194# ecpp0 at pci0					# parallel port ?
195
196## Mostek clock found on 4/300, sun4c, sun4m and sun4u systems.
197## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems.
198clock0	at sbus0 slot ? offset ?
199#clock0	at pci0
200
201## Timer chip found on 4/300, sun4c, sun4m and sun4u systems.
202timer0	at mainbus0				# sun4c
203
204#### Serial port configuration
205
206## Zilog 8530 serial chips.  Each has two-channels.
207## zs0 is ttya and ttyb.  zs1 is the keyboard and mouse.
208zs0	at sbus0 slot ? offset ?
209zstty0	at zs0 channel 0	# ttya
210zstty1	at zs0 channel 1	# ttyb
211
212zs1	at sbus0 slot ? offset ?
213kbd0	at zs1 channel 0	# keyboard
214ms0	at zs1 channel 1	# mouse
215
216## PCI machines apparently have serial ports
217## called `se' and `su'
218
219## Part of a PC87332VLJ?
220#se0	at ebus?		# 
221#kbd0	at su1 channel 0	# keyboard
222#ms0	at su1 channel 1	# mouse
223
224## These are two SAB82532 controllers
225#su0	at ebus?		# ttya
226#su1	at ebus?		# ttyb
227
228#### Disk controllers and disks
229
230## The following flags may be set for the NCR53c94 based esp driver:
231##	bits 0-7:  disable disconnect/reselect for the corresponding target
232##	bits 8-15: disable synchronous negotiation for target [bit-8]
233
234## sun4/300, sun4c, sun4m and sun4u on-board SCSI, and FSBE/S SBus SCSI cards.
235## Both `dma' and `esp' are needed in all cases.
236## Two kinds of additional SBus SCSI interfaces are available.  One uses
237## "esp at sbus" like the sun4c on-board; the other uses "esp at dma".
238
239## sun4/300 SCSI - an NCR53c94 or equivalent behind
240## an LSI Logic DMA controller
241
242dma0	at sbus0 slot ? offset ?			# sun4c/sun4m/sun4u
243esp0	at dma0 flags 0x0000				# sun4m/sun4u
244scsibus* at esp?
245
246# FSBE/S SCSI
247dma*	at sbus? slot ? offset ?			# SBus
248esp*	at dma? flags 0x0000				# SBus
249
250scsibus* at esp?
251
252## Qlogic ISP SBus SCSI Card
253isp*	at sbus? slot ? offset ?
254scsibus* at isp?
255
256## FAS support missing
257#fas*	at sbus? slot ? offset ?
258#scsibus* at fas?
259
260## GLM support is missing
261#scsi*	at pci?						# 53C875 "glm" compatible
262
263## These entries find devices on all SCSI busses and assign
264## unit numbers dynamically.
265sd*	at scsibus? target ? lun ?		# SCSI disks
266st*	at scsibus? target ? lun ?		# SCSI tapes
267cd*	at scsibus? target ? lun ?		# SCSI CD-ROMs
268ch*	at scsibus? target ? lun ?		# SCSI changer devices
269ss*	at scsibus? target ? lun ?		# SCSI scanners
270uk*	at scsibus? target ? lun ?		# unknown SCSI
271
272## Floppy controller and drive found on SPARCstations.
273
274# need share with the sparc...uses auxreg.  what is this on sparc64?
275#fdc0	at sbus0 slot ? offset ?
276#fdc0	at pci?					# Called fdthree?
277#fd*	at fdc0 	 			# the drive itself
278
279## A disk-like interface to files.  Can be used to create floppy, CD,
280## miniroot images, etc.
281
282pseudo-device	vnd	4
283
284## Concatenated and striped disks; with this, you can create a software-based
285## disk array similar to a "RAID 0" setup.  See ccd(4).
286
287pseudo-device	ccd	4
288
289## RAIDframe disk driver: software RAID driver.  See raid(4).
290
291pseudo-device	raid	4
292
293## Memory disk device, used on boot floppies with compressed
294## kernel-plus-root-disk images.
295
296pseudo-device	md	1
297
298
299#### Network interfaces
300
301## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue
302## Three flavors of additional SBus ethernets are available.  One attaches
303## directly like the sun4c on-board, one uses the ledma device like the
304## sun4m on-board, and one uses the lebuffer device.
305
306ledma0		at sbus0 slot ? offset ?		# sun4m on-board
307le0		at ledma0				# sun4m on-board
308le*		at sbus? slot ? offset ?		# SBus
309ledma*		at sbus? slot ? offset ?		# SBus
310le*		at ledma?				# SBus
311lebuffer0	at sbus? slot ? offset ?		# SBus
312le0		at lebuffer?				# SBus
313lebuffer*	at sbus? slot ? offset ?		# SBus
314le*		at lebuffer?				# SBus
315
316## HME not supported yet
317#hme*		at sbus0 slot ? offset ?
318#network*	at pci?					# "hme" compatible
319
320## qec/be, qec/hme
321qec*		at sbus? slot ? offset ?
322be*		at qec?
323qe*		at qec?
324
325## Loopback network interface; required
326pseudo-device	loop
327
328## SLIP and CSLIP interfaces, for IP over a serial line.
329pseudo-device	sl		2
330
331## PPP, the successor to SLIP.  See pppd(8).
332pseudo-device	ppp		2
333
334## Starmode Radio IP, a special hardware network device.
335pseudo-device	strip		1
336
337## Network "tunnel" device, allowing protocol stacks to run in the userland.
338## This is used by the third-party user-mode "ppp" program, and others.
339pseudo-device	tun		4
340
341## Generic L3 over IP tunnel
342#pseudo-device	gre		2	# generic L3 over IP tunnel
343
344## Berkeley Packet Filter, required to run RARPD.  A generic C-language
345## interface that allows selective examining of incoming packets.
346pseudo-device	bpfilter	8
347
348## IP Filter, used in firewall and NAT applications.  See ipnat(8) for
349## one example of the use of the IP Filter.
350pseudo-device	ipfilter
351
352
353#### Audio and video devices
354
355## /dev/audio support (`audiocs' plus `audio')
356##
357audiocs0	at sbus0 slot ? offset ?		# SUNW,CS4231
358audio*		at audiocs0
359
360
361## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m
362## systems.  If your sun4 system has a cgfour installed in the P4 slot,
363## the P4 entries for "bwtwo" will attach to the overlay plane of the
364## "cgfour".
365
366#bwtwo0		at sbus0 slot ? offset ?		# sun4c and sun4m
367#bwtwo*		at sbus? slot ? offset ?		#
368
369## Sun "cgthree" Sbus color framebuffer
370#cgthree0	at sbus? slot ? offset ?
371#cgthree*	at sbus? slot ? offset ?
372
373## Sun "cgsix" accelerated color framebuffer.
374cgsix0		at sbus? slot ? offset ?
375cgsix*		at sbus? slot ? offset ?
376
377## Sun "tcx" accelerated color framebuffer.
378#tcx0		at sbus? slot ? offset ?
379#tcx*		at sbus? slot ? offset ?
380
381# Sun "cgfourteen" accelerated 24-bit framebuffer.
382#cgfourteen0	at obio0			# sun4m
383
384## Sun FFB not supported
385#ffb*		at upa?
386
387#### Other device configuration
388
389## Pseudo ttys, required for network logins and programs like screen.
390## 32 is a good number for average systems; you may have as many as you
391## like, though 256 is more or less the upper limit.  Increasing this
392## number still requires you to run /dev/MAKEDEV to create the files
393## for the ptys.
394
395pseudo-device	pty		64	# pseudo-ttys (for network, etc.)
396
397## Random device, used to implement /dev/random (a source of random noise),
398## and generate randomness for some kernel formulae.
399## THIS DEVICE IS EXPERIMENTAL; use at your own risk.
400
401pseudo-device	rnd
402