Home | History | Annotate | Line # | Download | only in conf
GENERIC revision 1.17
      1 # 	$NetBSD: GENERIC,v 1.17 1999/07/18 23:52:58 eeh Exp $
      2 
      3 include "arch/sparc64/conf/std.sparc64"
      4 
      5 maxusers	32
      6 
      7 ## System kernel configuration.  See options(4) for more detail.
      8 
      9 
     10 # Options for variants of the Sun SPARC architecure.
     11 # We currently support three architecture types; at least one is required.
     12 options		SUN4U		# sun4u - Ultra 140 and 170
     13 options		TRAPWIN
     14 options		__ELF__		# we use elf 
     15 #options		_LP64		# we're using a 64-bit compiler
     16 
     17 ## System options specific to the sparc machine type
     18 
     19 ## Use a faster console than the PROM's slow drawing routines.  Not needed
     20 ## for headless (no framebuffer) machines.
     21 # XXX broken on sparc64
     22 #options 	RASTERCONSOLE		# fast rasterop console
     23 
     24 #### System options that are the same for all ports
     25 
     26 ## Root device configuration: change the ?'s if you are going to use a
     27 ## nonstandard root partition (other than where the kernel is booted from)
     28 ## and/or nonstandard root type (not ffs or nfs).  Normally this can be
     29 ## automagically determined at boot time.
     30 
     31 config		netbsd	root on ? type ?
     32 
     33 ## UVM options.
     34 #options	UVM_PAGE_TRKOWN
     35 #options 	UVMHIST
     36 #options 	UVMHIST_PRINT	# Loud!
     37 options 	PMAP_NEW
     38 
     39 ## System call tracing (see ktrace(1)).
     40 options 	KTRACE
     41 
     42 ## Collect statistics on kernel malloc's and free's.  This does have a
     43 ## significant performance hit on slower machines, so it is intended for
     44 ## diagnostic use only.
     45 #options 	KMEMSTATS
     46 
     47 ## System V compatible IPC subsystem.  (msgctl(2), semctl(2), and shmctl(2))
     48 options 	SYSVMSG		# System V message queues
     49 options 	SYSVSEM		# System V semaphores
     50 options 	SYSVSHM		# System V shared memory
     51 #options 	SHMMAXPGS=1024	# 1024 pages is the default
     52 
     53 ## Loadable kernel module support; still under development.
     54 options 	LKM
     55 
     56 ## NFS boot options; default on sparc is the bootparam protocol
     57 options 	NFS_BOOT_BOOTPARAM
     58 #options 	NFS_BOOT_BOOTP
     59 #options 	NFS_BOOT_DHCP
     60 
     61 #### Debugging options
     62 
     63 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at
     64 ## serial console break or keyboard reset, where the PROM would normally
     65 ## intercept.  DDB_HISTORY_SIZE adds up/down arrow command history.
     66 # we enable DDB in GENERIC for now.
     67 options 	DDB			# kernel dynamic debugger
     68 options 	DDB_HISTORY_SIZE=100	# enable history editing in DDB
     69 #options 	DDB_ONPANIC		# see also sysctl(8): `ddb.onpanic'
     70 
     71 ## You may also use gdb, on another computer connected to this machine over
     72 ## a serial port.  Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is
     73 ## a dev_t encoded device number of the serial port to use.
     74 ## (0xc01 = ttya, 0xc02 = ttyb.)
     75 #options 	KGDB		# support for kernel gdb
     76 #options 	KGDBDEV=0xc01	# kgdb device number (this sample is `ttyb')
     77 #options 	KGDBRATE=38400	# baud rate
     78 
     79 
     80 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file),
     81 ## such that gdb(1) can be used on a kernel coredump.
     82 
     83 #makeoptions 	DEBUG="-g"
     84 
     85 
     86 ## Adds code to the kernel that does internal consistency checks, and will
     87 ## cause the kernel to panic if corruption of internal data structures
     88 ## is detected.
     89 #options 	DIAGNOSTIC	# extra kernel sanity checking
     90 
     91 ## Enable (possibly expensive) debugging code that may also display messages
     92 ## on the system console
     93 #options 	DEBUG
     94 
     95 ## Make SCSI error messages more verbose when explaining their meanings.
     96 options 	SCSIVERBOSE
     97 options 	PCIVERBOSE
     98 
     99 ## `INSECURE' turns off the kernel security level (securelevel = 0 always).
    100 ## This allows writing to /dev/mem, loading kernel modules while multi-user,
    101 ## and other insecurities good only for development work.  Do not use this
    102 ## option on a production machine.
    103 #options 	INSECURE
    104 
    105 ## Allow non-root users to grab /dev/console with programs such as xconsole.
    106 ## `xconsole' therefore does not need setuid root with this option enabled.
    107 #options 	UCONSOLE
    108 
    109 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a
    110 ## pre-opened opaque file to the script interpreter.  `SETUIDSCRIPTS',
    111 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same
    112 ## opaque file mechanism.  Perl calls this "secure setuid scripts."
    113 
    114 #options 	FDSCRIPTS
    115 #options 	SETUIDSCRIPTS
    116 
    117 ## Options for compatibility with previous releases foreign system binaries.
    118 ## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up
    119 ## additional user-level utilities or system configuration files. See
    120 ## compat_sunos(8) and compat_svr4(8).
    121 
    122 options 	COMPAT_43	# 4.3BSD system interfaces
    123 options 	COMPAT_10	# NetBSD 1.0 binary compatibility
    124 options 	COMPAT_11	# NetBSD 1.1 binary compatibility
    125 options 	COMPAT_12	# NetBSD 1.2 binary compatibility
    126 options 	COMPAT_13	# NetBSD 1.3 binary compatibility
    127 #options 	COMPAT_NETBSD32	# NetBSD/sparc binary compatibility -- 64-bit only
    128 options 	COMPAT_SUNOS	# SunOS 4.x binary compatibility
    129 options 	COMPAT_SVR4	# SunOS 5.x binary compatibility
    130 options 	EXEC_ELF32	# Exec module for SunOS 5.x binaries.
    131 #options		EXEC_ELF64	# Exec module for sparc64 & SunOs 5.x binaries. -- 64-bit only
    132 #options		SYSCALL_DEBUG
    133 options		COMPAT_AOUT	# NetBSD/sparc compat support
    134 options 	EXEC_AOUT	# execve(2) support for a.out binaries
    135 
    136 ## File systems.  You probably need at least one of FFS or NFS.
    137 file-system	FFS		# Berkeley Fast Filesystem
    138 file-system	NFS		# Sun NFS-compatible filesystem client
    139 file-system	KERNFS		# kernel data-structure filesystem
    140 file-system	NULLFS		# NULL layered filesystem
    141 file-system	MFS		# memory-based filesystem
    142 file-system	FDESC		# user file descriptor filesystem
    143 file-system	UMAPFS		# uid/gid remapping filesystem
    144 file-system	LFS		# Log-based filesystem (still experimental)
    145 file-system	PORTAL		# portal filesystem (still experimental)
    146 file-system	PROCFS		# /proc
    147 file-system	CD9660		# ISO 9660 + Rock Ridge file system
    148 file-system	UNION		# union file system
    149 file-system	MSDOSFS		# MS-DOS FAT filesystem(s).
    150 
    151 ## File system options.
    152 options 	NFSSERVER	# Sun NFS-compatible filesystem server
    153 options 	QUOTA		# FFS quotas
    154 #options 	FFS_EI		# FFS Endian Independent support
    155 
    156 ## Network protocol support.  In most environments, INET is required.
    157 options 	INET		# IP (Internet Protocol) v4
    158 options 	TCP_COMPAT_42	# 4.2BSD IP implementation compatibility
    159 #options 	GATEWAY		# packet forwarding ("router switch")
    160 options 	MROUTING	# packet forwarding of multicast packets
    161 #options 	DIRECTED_BROADCAST	# allow broadcasts through routers
    162 options 	NS		# Xerox NS networking
    163 #options 	NSIP		# Xerox NS tunneling over IP
    164 options 	ISO,TPIP	# OSI networking
    165 options 	EON		# OSI tunneling over IP
    166 #options 	CCITT,LLC,HDLC	# X.25 packet switched protocol
    167 options 	NETATALK	# AppleTalk (over Ethernet) protocol
    168 options 	NTP		# Network Time Protocol in-kernel support
    169 #options 	PPS_SYNC	# Add serial line synchronization for NTP
    170 options 	PFIL_HOOKS	# Add pfil(9) hooks, intended for custom LKMs.
    171 options 	IPFILTER_LOG	# Add ipmon(8) logging for ipfilter device
    172 options 	PPP_BSDCOMP	# Add BSD compression to ppp device
    173 options 	PPP_DEFLATE	# Add deflate (libz) compression to ppp device
    174 options 	PPP_FILTER	# Add active filters for ppp (via bpf)
    175 
    176 
    177 #### Main bus and CPU .. all systems.
    178 mainbus0 at root
    179 cpu0	at mainbus0
    180 
    181 #### Bus types found on SPARC systems.
    182 
    183 sbus0	at mainbus0				# Ultra 1
    184 #upa0	at mainbus0				# Ultra 1E, Ultra 2, Ex0000
    185 psycho*	at mainbus0				# Darwin, Ultra5
    186 pci*	at psycho?
    187 pci*	at simba?
    188 simba*	at pci? dev ? function ?		# `APB' support.
    189 ebus*	at pci?					# ebus devices
    190 
    191 #### Standard system devices -- all required for a given architecture
    192 
    193 ## Auxiliary system registers -- We use the OBP for power management
    194 #auxreg0 at sbus0
    195 #auxreg0 at pci0
    196 
    197 # We also need:
    198 # bpp0 at sbus0					# parallel port
    199 # ecpp0 at pci0					# parallel port ?
    200 lpt*	at ebus?				# parallel port
    201 
    202 ## Mostek clock found on 4/300, sun4c, sun4m and sun4u systems.
    203 ## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems.
    204 clock0	at sbus0 slot ? offset ?
    205 clock0	at ebus?
    206 
    207 ## Timer chip found on 4/300, sun4c, sun4m and sun4u systems.
    208 timer0	at mainbus0				# sun4c
    209 
    210 #### Serial port configuration
    211 
    212 ## Zilog 8530 serial chips.  Each has two-channels.
    213 ## zs0 is ttya and ttyb.  zs1 is the keyboard and mouse.
    214 zs0	at sbus0 slot ? offset ?
    215 zstty0	at zs0 channel 0	# ttya
    216 zstty1	at zs0 channel 1	# ttyb
    217 
    218 zs1	at sbus0 slot ? offset ?
    219 kbd0	at zs1 channel 0	# keyboard
    220 ms0	at zs1 channel 1	# mouse
    221 
    222 ## PCI machines apparently have serial ports
    223 ##	Siemens SAB82532 controller: ttya and ttyb (sab)
    224 ##	Part of NS PC87332VLJ Super I/O controller: kbd/mouse (com)
    225 
    226 ## These are two SAB82532 controllers
    227 #sab0	at ebus?			# ttya/ttyb
    228 #sabtty0	at sab0 channel 0	# ttya
    229 #sabtty1	at sab0 channel 1	# ttyb
    230 
    231 ## Part of a PC87332VLJ?
    232 #ucom0	at ebus? addr 0x3083f8		# `com' driver
    233 #ucom1	at ebus? addr 0x3062f8		# 
    234 #ucom0	at ebus?			# `com' driver
    235 #ucom1	at ebus?			# 
    236 #kbd0	at ucom0 channel 0		# keyboard
    237 #ms0	at ucom1 channel 1		# mouse
    238 
    239 #### Disk controllers and disks
    240 
    241 ## The following flags may be set for the NCR53c94 based esp driver:
    242 ##	bits 0-7:  disable disconnect/reselect for the corresponding target
    243 ##	bits 8-15: disable synchronous negotiation for target [bit-8]
    244 
    245 ## sun4/300, sun4c, sun4m and sun4u on-board SCSI, and FSBE/S SBus SCSI cards.
    246 ## Both `dma' and `esp' are needed in all cases.
    247 ## Two kinds of additional SBus SCSI interfaces are available.  One uses
    248 ## "esp at sbus" like the sun4c on-board; the other uses "esp at dma".
    249 
    250 ## sun4/300 SCSI - an NCR53c94 or equivalent behind
    251 ## an LSI Logic DMA controller
    252 
    253 dma0	at sbus0 slot ? offset ?			# sun4c/sun4m/sun4u
    254 esp0	at dma0 flags 0x0000				# sun4m/sun4u
    255 scsibus* at esp?
    256 
    257 # FSBE/S SCSI
    258 dma*	at sbus? slot ? offset ?			# SBus
    259 esp*	at dma? flags 0x0000				# SBus
    260 
    261 scsibus* at esp?
    262 
    263 ## Qlogic ISP SBus SCSI Card
    264 isp*	at sbus? slot ? offset ?
    265 scsibus* at isp?
    266 
    267 ## FAS support missing
    268 #fas*	at sbus? slot ? offset ?
    269 #scsibus* at fas?
    270 
    271 ## GLM support is missing
    272 #scsi*	at pci?						# 53C875 "glm" compatible
    273 
    274 ## These entries find devices on all SCSI busses and assign
    275 ## unit numbers dynamically.
    276 sd*	at scsibus? target ? lun ?		# SCSI disks
    277 st*	at scsibus? target ? lun ?		# SCSI tapes
    278 cd*	at scsibus? target ? lun ?		# SCSI CD-ROMs
    279 ch*	at scsibus? target ? lun ?		# SCSI changer devices
    280 ss*	at scsibus? target ? lun ?		# SCSI scanners
    281 uk*	at scsibus? target ? lun ?		# unknown SCSI
    282 
    283 # PCI IDE.
    284 pciide* at pci ? dev ? function ? flags 0x0000
    285 wd*     at pciide? channel ? drive ? flags 0x0000
    286 atapibus* at pciide? channel ?
    287 
    288 cd*	at atapibus? drive ? flags 0x0000	# ATAPI CD-ROM drives
    289 sd*	at atapibus? drive ? flags 0x0000	# ATAPI disk drives
    290 uk*	at atapibus? drive ? flags 0x0000	# ATAPI unknown
    291 
    292 ## Floppy controller and drive found on SPARCstations.
    293 
    294 # need share with the sparc...uses auxreg.  what is this on sparc64?
    295 #fdc0	at sbus0 slot ? offset ?
    296 #fdc0	at pci?					# Called fdthree?
    297 #fd*	at fdc0 	 			# the drive itself
    298 
    299 ## A disk-like interface to files.  Can be used to create floppy, CD,
    300 ## miniroot images, etc.
    301 
    302 pseudo-device	vnd	4
    303 
    304 ## Concatenated and striped disks; with this, you can create a software-based
    305 ## disk array similar to a "RAID 0" setup.  See ccd(4).
    306 
    307 pseudo-device	ccd	4
    308 
    309 ## RAIDframe disk driver: software RAID driver.  See raid(4).
    310 
    311 pseudo-device	raid	4
    312 
    313 ## Memory disk device, used on boot floppies with compressed
    314 ## kernel-plus-root-disk images.
    315 
    316 pseudo-device	md	1
    317 
    318 
    319 #### Network interfaces
    320 
    321 ## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue
    322 ## Three flavors of additional SBus ethernets are available.  One attaches
    323 ## directly like the sun4c on-board, one uses the ledma device like the
    324 ## sun4m on-board, and one uses the lebuffer device.
    325 
    326 ledma0		at sbus0 slot ? offset ?		# sun4m on-board
    327 le0		at ledma0				# sun4m on-board
    328 le*		at sbus? slot ? offset ?		# SBus
    329 ledma*		at sbus? slot ? offset ?		# SBus
    330 le*		at ledma?				# SBus
    331 lebuffer0	at sbus? slot ? offset ?		# SBus
    332 le0		at lebuffer?				# SBus
    333 lebuffer*	at sbus? slot ? offset ?		# SBus
    334 le*		at lebuffer?				# SBus
    335 
    336 ## HME not supported yet
    337 #hme*		at sbus0 slot ? offset ?
    338 #network*	at pci?					# "hme" compatible
    339 
    340 ## qec/be, qec/hme
    341 qec*		at sbus? slot ? offset ?
    342 be*		at qec?
    343 qe*		at qec?
    344 
    345 ## Loopback network interface; required
    346 pseudo-device	loop
    347 
    348 ## SLIP and CSLIP interfaces, for IP over a serial line.
    349 pseudo-device	sl		2
    350 
    351 ## PPP, the successor to SLIP.  See pppd(8).
    352 pseudo-device	ppp		2
    353 
    354 ## Starmode Radio IP, a special hardware network device.
    355 pseudo-device	strip		1
    356 
    357 ## Network "tunnel" device, allowing protocol stacks to run in the userland.
    358 ## This is used by the third-party user-mode "ppp" program, and others.
    359 pseudo-device	tun		4
    360 
    361 ## Generic L3 over IP tunnel
    362 #pseudo-device	gre		2	# generic L3 over IP tunnel
    363 
    364 ## Berkeley Packet Filter, required to run RARPD.  A generic C-language
    365 ## interface that allows selective examining of incoming packets.
    366 pseudo-device	bpfilter	8
    367 
    368 ## IP Filter, used in firewall and NAT applications.  See ipnat(8) for
    369 ## one example of the use of the IP Filter.
    370 pseudo-device	ipfilter
    371 
    372 
    373 #### Audio and video devices
    374 
    375 ## /dev/audio support (`audiocs' plus `audio')
    376 ##
    377 audiocs0	at sbus0 slot ? offset ?		# SUNW,CS4231
    378 audio*		at audiocs0
    379 
    380 
    381 ## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m
    382 ## systems.  If your sun4 system has a cgfour installed in the P4 slot,
    383 ## the P4 entries for "bwtwo" will attach to the overlay plane of the
    384 ## "cgfour".
    385 
    386 #bwtwo0		at sbus0 slot ? offset ?		# sun4c and sun4m
    387 #bwtwo*		at sbus? slot ? offset ?		#
    388 
    389 ## Sun "cgthree" Sbus color framebuffer
    390 #cgthree0	at sbus? slot ? offset ?
    391 #cgthree*	at sbus? slot ? offset ?
    392 
    393 ## Sun "cgsix" accelerated color framebuffer.
    394 cgsix0		at sbus? slot ? offset ?
    395 cgsix*		at sbus? slot ? offset ?
    396 
    397 ## Sun "tcx" accelerated color framebuffer.
    398 #tcx0		at sbus? slot ? offset ?
    399 #tcx*		at sbus? slot ? offset ?
    400 
    401 # Sun "cgfourteen" accelerated 24-bit framebuffer.
    402 #cgfourteen0	at obio0			# sun4m
    403 
    404 ## Sun FFB not supported
    405 #ffb*		at upa?
    406 
    407 #### Other device configuration
    408 
    409 ## Pseudo ttys, required for network logins and programs like screen.
    410 ## 32 is a good number for average systems; you may have as many as you
    411 ## like, though 256 is more or less the upper limit.  Increasing this
    412 ## number still requires you to run /dev/MAKEDEV to create the files
    413 ## for the ptys.
    414 
    415 pseudo-device	pty		64	# pseudo-ttys (for network, etc.)
    416 
    417 ## Random device, used to implement /dev/random (a source of random noise),
    418 ## and generate randomness for some kernel formulae.
    419 ## THIS DEVICE IS EXPERIMENTAL; use at your own risk.
    420 
    421 pseudo-device	rnd
    422