GENERIC revision 1.69
1# $NetBSD: GENERIC,v 1.69 2008/07/31 07:41:07 simonb Exp $ 2# 3# GENERIC machine description file 4# 5# This machine description file is used to generate the default NetBSD 6# kernel. The generic kernel does not include all options, subsystems 7# and device drivers, but should be useful for most applications. 8# 9# The machine description file can be customised for your specific 10# machine to reduce the kernel size and improve its performance. 11# 12# For further information on compiling NetBSD kernels, see the config(8) 13# man page. 14# 15# For further information on hardware support for this architecture, see 16# the intro(4) man page. For further information about kernel options 17# for this architecture, see the options(4) man page. For an explanation 18# of each device driver in this file see the section 4 man page for the 19# device. 20 21# Supports Sun2 (2/120, 2/170, 2/50, ...) 22# Supports root on: ie0, sd*, ... 23 24include "arch/sun2/conf/std.sun2" 25 26options INCLUDE_CONFIG_FILE # embed config file in kernel binary 27 28#ident "GENERIC-$Revision: 1.69 $" 29 30makeoptions COPTS="-Os" # optimize for size 31 32# Machines to be supported by this kernel 33#options FPU_EMULATE 34 35# Needs to be set per system. i.e change these as you see fit 36maxusers 4 37 38# Standard system options 39options KTRACE # system call tracing 40options SYSVMSG # System V message queues 41options SYSVSEM # System V semaphores 42options SYSVSHM # System V shared memory 43options P1003_1B_SEMAPHORE # p1003.1b semaphore support 44options LKM # loadable kernel modules 45#options INSECURE # disable kernel security level 46#options USERCONF # userconf(4) support 47#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 48options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 49 50# Enable experimental buffer queue strategy for better responsiveness under 51# high disk I/O load. Use it with caution - it's not proven to be stable yet. 52#options BUFQ_READPRIO 53#options BUFQ_PRIOCSCAN 54 55# Which kernel debugger? Uncomment either this: 56options DDB 57# ... or these for KGDB (gdb remote target) 58#makeoptions DEBUG="-g" # debugging symbols for gdb 59#options KGDB 60#options KGDB_DEV=0x0C00 # ttya=0C00 ttyb=0C01 61 62# Other debugging options 63#options DDB_HISTORY_SIZE=100 # enable history editing in DDB 64#options DEBUG # kernel debugging code 65#options DIAGNOSTIC # extra kernel sanity checking 66#options KMEMSTATS # kernel memory statistics (vmstat -m) 67#options PMAP_DEBUG 68#options SCSIDEBUG 69#options SCSIVERBOSE # Verbose SCSI errors 70 71# Compatibility options 72#options COMPAT_SUNOS # can run SunOS 4.1.1 executables 73options COMPAT_43 # and 4.3BSD and ... 74options COMPAT_16 # NetBSD 1.6 75options COMPAT_20 # NetBSD 2.0 76options COMPAT_30 # NetBSD 3.0 77options COMPAT_40 # NetBSD 4.0 compatibility. 78options COMPAT_AOUT_M68K # support for NetBSD a.out executables 79#options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended. 80options EXEC_AOUT # support for a.out executables 81options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 82 83# Filesystem options 84file-system FFS # Berkeley Fast Filesystem 85file-system NFS # Sun NFS client support 86file-system CD9660 # ISO 9660 + Rock Ridge file system 87file-system FDESC # /dev/fd/* 88file-system KERNFS # /kern 89file-system NULLFS # loopback file system 90#file-system OVERLAY # overlay file system 91#file-system PROCFS # /proc 92#file-system UNION # union file system 93file-system MFS # memory-based filesystem 94file-system PTYFS # /dev/pts/N support 95#file-system TMPFS # Efficient memory file-system 96#file-system UDF # experimental - OSTA UDF CD/DVD file-system 97 98options NFSSERVER # nfs server support 99#options QUOTA # FFS quotas 100#options FFS_EI # FFS Endian Independant support 101options SOFTDEP # FFS soft updates support. 102options WAPBL # File system journaling support - Experimental 103#options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 104#options NFS_V2_ONLY # Exclude NFS3 code to save space 105options FFS_NO_SNAPSHOT # No FFS snapshot support 106 107# Networking options 108options INET # IP protocol stack support 109#options INET6 # IPV6 110#options IPSEC # IP security 111#options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 112#options IPSEC_NAT_T # IPsec NAT traversal (NAT-T) 113#options IPSEC_DEBUG # debug for IP security 114#options GATEWAY # IP packet forwarding 115#options ISO,TPIP # OSI networking 116#options EON # OSI tunneling over IP 117options PFIL_HOOKS # pfil(9) packet filter hooks. 118#options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG 119 120#options ALTQ # Manipulate network interfaces' output queues 121#options ALTQ_BLUE # Stochastic Fair Blue 122#options ALTQ_CBQ # Class-Based Queueing 123#options ALTQ_CDNR # Diffserv Traffic Conditioner 124#options ALTQ_FIFOQ # First-In First-Out Queue 125#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 126#options ALTQ_HFSC # Hierarchical Fair Service Curve 127#options ALTQ_LOCALQ # Local queueing discipline 128#options ALTQ_PRIQ # Priority Queueing 129#options ALTQ_RED # Random Early Detection 130#options ALTQ_RIO # RED with IN/OUT 131#options ALTQ_WFQ # Weighted Fair Queueing 132 133# Work-around for root on slow servers (insurance...) 134options NFS_BOOT_RWSIZE=1024 135options NFS_BOOT_BOOTPARAM 136 137config netbsd root on ? type ? 138 139#### Main bus. 140mainbus0 at root 141 142#### Bus types. 143 144obio0 at mainbus? # all Sun-2 145obmem0 at mainbus? # all Sun-2 146mbmem0 at mainbus? # 2/120, 2/170 147mbio0 at mainbus? # 2/120, 2/170 148sun68kvme0 at mainbus? # 2/50, 2/130, 2/160 149vme0 at sun68kvme0 # mi VME attachment 150 151#### Standard system devices. 152 153## The AM9513 clock chip. 154clock0 at obio0 addr 0x002800 # 2/120, 2/170 155clock0 at obio0 addr 0x7f2800 # 2/50, 2/130, 2/160 156 157## The MM58167 time-of-day chip. 158tod0 at obio0 addr 0x003800 # 2/120, 2/170 159tod0 at vme0 addr 0x200800 # 2/50, 2/130, 2/160 160 161#### Serial port configuration. 162 163## Zilog 8530 serial chips. Each has two channels. 164## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 165## zs0 is REQUIRED to use KGDB. 166zs0 at obio0 addr 0x002000 # 2/120, 2/170 167zs0 at obio0 addr 0x7f2000 # 2/50 168zs1 at obmem0 addr 0x780000 # 2/120, 2/170 169zs1 at obio0 addr 0x7f1800 # 2/50 170zs2 at mbmem0 addr 0x080800 # 2/120, 2/170 (first sc SCSI) 171zs3 at mbmem0 addr 0x081000 # 2/120, 2/170 (first sc SCSI) 172zs4 at mbmem0 addr 0x084800 # 2/120, 2/170 (second sc SCSI) 173zs5 at mbmem0 addr 0x085000 # 2/120, 2/170 (second sc SCSI) 174zstty* at zs? channel ? # ttya 175kbd0 at zstty? # keyboard 176ms0 at zstty? # mouse 177 178#### Disk controllers and disks. 179 180## PAL+logic-based "Sun SCSI 2" Multibus/VME SCSI controller. 181## This driver has several flags which may be enabled using 182## the "flags" directive. Valid flags are: 183## 184## 0x0ff Set (1<<target) to disable parity checking 185## 0x100 Set this bit to disable DMA interrupts (poll) 186## 0x200 Set this bit to disable DMA entirely (use PIO) 187## 188## For example: "flags 0x10f" would disable DMA interrupts, 189## and disable parity for targets 0-3 190 191sc0 at mbmem0 addr 0x80000 ipl 2 flags 0xff 192sc0 at vme0 addr 0x200000 irq 2 vect 0x40 flags 0xff 193sc1 at mbmem0 addr 0x84000 ipl 2 flags 0xff 194 195## NCR5380-based "Sun SCSI 3" VME SCSI controller. 196## This driver has several flags which may be enabled by OR'ing 197## the values and using the "flags" directive. 198## Valid flags are: 199## 200## 0x01 Use DMA (may be polled) 201## 0x02 Use DMA completion interrupts 202## 0x04 Allow disconnect/reselect 203## 204## E.g. the following would enable DMA, interrupts, and reselect: 205## si0 at vme0 addr 0x200000 ipl 3 vect 0x40 flags 0x07 206## 207## By default, DMA is enabled in the driver. 208 209si0 at vme0 addr 0x200000 irq 2 vect 0x40 210 211## These entries find devices on all SCSI busses and assign 212## unit numbers dynamically. 213scsibus* at sc? 214scsibus* at si? 215sd* at scsibus? target ? lun ? # SCSI disks 216st* at scsibus? target ? lun ? # SCSI tapes 217cd* at scsibus? target ? lun ? # SCSI CD-ROMs 218#ch* at scsibus? target ? lun ? # SCSI changer devices 219#ss* at scsibus? target ? lun ? # SCSI scanners 220#ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 221#uk* at scsibus? target ? lun ? # unknown SCSI 222 223# support old SCSI devices that don't understand the INQUIRY command 224options SCSI_OLD_NOINQUIRY 225 226## Xylogics 450 or 451 Multibus/VME SMD disk controllers and disks. 227#xyc0 at mbio0 addr 0xee40 ipl 2 228xyc0 at vme0 addr 0xee40 irq 2 vect 0x48 229#xyc1 at mbio0 addr 0xee48 ipl 2 230xyc1 at vme0 addr 0xee48 irq 2 vect 0x49 231xy* at xyc? drive ? 232 233## Memory-disk device. 234pseudo-device md 2 235 236#### Network interfaces. 237 238## Intel Ethernet (onboard, or Multibus/VME) 239ie0 at obio0 addr 0x7f0800 ipl 3 # 2/50 240ie0 at mbmem0 addr 0x88000 ipl 3 241ie1 at mbmem0 addr 0x8c000 ipl 3 242## VME: the first [addr,len] pair specifies the device registers; 243## the second pair specifies the on-board memory buffer 244ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 245 246## 3Com Ethernet (Multibus only) 247ec0 at mbmem0 addr 0xe0000 ipl 3 248ec1 at mbmem0 addr 0xe2000 ipl 3 249# limit NFS R/W size for poor ec(4) interfaces 250options NFS_RSIZE=1024,NFS_WSIZE=1024 251 252## Frame buffers. 253 254## Sun "bwtwo" black and white framebuffer. 255bwtwo0 at obmem0 addr 0x700000 # 2/120, 2/170 256bwtwo0 at obio0 addr 0x0 # 2/50 257 258## PROM console driver -- if all else fails 259pcons0 at mainbus0 # PROM console 260 261#### Miscellaneous. 262pseudo-device loop 1 # network loopback 263#pseudo-device bpfilter # packet filter 264#pseudo-device carp # Common Address Redundancy Protocol 265#pseudo-device bridge # simple inter-network bridging 266#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 267#pseudo-device sl # CSLIP 268#pseudo-device ppp # PPP 269#pseudo-device pppoe # PPP over Ethernet (RFC 2516) 270#pseudo-device tun # network tunneling over tty 271#pseudo-device tap # virtual Ethernet 272#pseudo-device gre # generic L3 over IP tunnel 273#pseudo-device ipfilter # ip filter 274#pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 275#pseudo-device faith # IPv[46] tcp relay translation i/f 276#pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 277pseudo-device rnd # /dev/random and in-kernel generator 278 279pseudo-device pty # pseudo-terminals 280#pseudo-device vnd # paging to files 281#options VND_COMPRESSION # compressed vnd(4) 282#pseudo-device ccd 4 # concatenated disks 283#pseudo-device cgd 4 # cryptographic disk devices 284#pseudo-device raid 4 # RAIDframe disk driver 285#options RAID_AUTOCONFIG # auto-configuration of RAID components 286# Options to enable various other RAIDframe RAID types. 287# options RF_INCLUDE_EVENODD=1 288# options RF_INCLUDE_RAID5_RS=1 289# options RF_INCLUDE_PARITYLOGGING=1 290# options RF_INCLUDE_CHAINDECLUSTER=1 291# options RF_INCLUDE_INTERDECLUSTER=1 292# options RF_INCLUDE_PARITY_DECLUSTERING=1 293# options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 294#pseudo-device fss 4 # file system snapshot device 295pseudo-device clockctl # user control of clock subsystem 296pseudo-device ksyms # /dev/ksyms 297#pseudo-device pf # PF packet filter 298#pseudo-device pflog # PF log if 299 300# Veriexec 301# 302# a pseudo device needed for veriexec 303#pseudo-device veriexec 1 304# 305# Uncomment the fingerprint methods below that are desired. Note that 306# removing fingerprint methods will have almost no impact on the kernel 307# code size. 308# 309#options VERIFIED_EXEC_FP_RMD160 310#options VERIFIED_EXEC_FP_SHA256 311#options VERIFIED_EXEC_FP_SHA384 312#options VERIFIED_EXEC_FP_SHA512 313#options VERIFIED_EXEC_FP_SHA1 314#options VERIFIED_EXEC_FP_MD5 315