xdreg.h revision 1.6.100.1
1 /* $NetBSD: xdreg.h,v 1.6.100.1 2011/03/05 20:52:12 rmind Exp $ */ 2 3 /* 4 * Copyright (c) 1995 Charles D. Cranor 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 16 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 17 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 18 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 19 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, 20 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 21 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 22 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 23 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 24 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 25 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 26 */ 27 28 /* 29 * x d r e g . h 30 * 31 * this file contains the description of the Xylogics 753/7053's hardware 32 * data structures. 33 * 34 * author: Chuck Cranor <chuck@netbsd> 35 */ 36 37 #define XDC_MAXDEV 4 /* max devices per controller */ 38 #define XDC_RESETUSEC 1000000 /* max time for xdc reset (page 21 says 1sec) */ 39 #define XDC_MAXIOPB 31 /* max number of iopbs that can be active */ 40 #define XDC_MAXTIME 4*1000000 /* four seconds before we give up and reset */ 41 #define XDC_MAXTRIES 4 /* max number of times to retry an operation */ 42 #define XDC_THROTTLE 32 /* DMA throttle */ 43 #define XDC_INTERLEAVE 0 /* interleave (for format param) */ 44 #define XDC_DPARAM 0 /* dparam (drive param) XDDP_EC32 or 0 */ 45 46 /* 47 * xdc device interface 48 * (lives in VME address space) 49 */ 50 51 struct xdc { 52 volatile u_char filler0; 53 volatile u_char xdc_iopbaddr0; /* iopb byte 0 (LSB) */ 54 volatile u_char filler1; 55 volatile u_char xdc_iopbaddr1; /* iopb byte 1 */ 56 volatile u_char filler2; 57 volatile u_char xdc_iopbaddr2; /* iopb byte 2 */ 58 volatile u_char filler3; 59 volatile u_char xdc_iopbaddr3; /* iopb byte 3 (MSB) */ 60 volatile u_char filler4; 61 volatile u_char xdc_iopbamod; /* iopb address modifier */ 62 volatile u_char filler5; 63 volatile u_char xdc_csr; /* control and status register */ 64 volatile u_char filler6; 65 volatile u_char xdc_f_err; /* fatal error register */ 66 }; 67 68 /* 69 * xdc_iopbamod: addressing modes 70 * When doing DMA, if the maximum address of the buffer is greater than 71 * 24 bits then you must use the 32 bit mode. Note that on many systems 72 * (e.g. sun-4/300) DVMA space is smaller than 24 bits, so there is no 73 * need for the 32 bit mode. However, the 32-bit mode hooks are in 74 * the driver in case it ever gets ported to an environment that needs it. 75 */ 76 77 #define XDC_ADDRMOD 0x3d /* standard address modifer, 24 bit max */ 78 #define XDC_ADDRMOD32 0x0d /* 32 bit version above */ 79 80 /* 81 * xdc_csr 82 */ 83 84 #define XDC_RMAINTMD 0x80 /* reserved maintenance mode (write) */ 85 #define XDC_BUSY 0x80 /* busy (read) */ 86 #define XDC_F_ERROR 0x40 /* fatal error (read) */ 87 #define XDC_MAINTMOD 0x20 /* maintenance mode (read/write) */ 88 #define XDC_RESET 0x08 /* soft reset (read/write) */ 89 #define XDC_ADDIOPB 0x04 /* add iopb/add pending (write) */ 90 #define XDC_ADDING 0x04 /* iopb add is pending (read) */ 91 #define XDC_CLRRIO 0x02 /* clear RIO (remove iopb) request (write) */ 92 #define XDC_REMIOPB 0x02 /* remove iopb (read) */ 93 #define XDC_RBUSYSEM 0x01 /* register busy semaphore (read/write) */ 94 95 /* 96 * Input/Output Parameter Block (iopb) 97 * 98 * all controller commands are done via iopb's. to start a command you 99 * must do this: 100 * [1] allocate space in DVMA space for the iopb 101 * [2] fill out all the fields of the iopb 102 * [3] check to see if controller can accept an iopb (XDC_ADDING bit clear) 103 * [4] put the DVMA address of the iopb in the xdc registers (in vme space) 104 * [5] set the XDC_ADDIOPB bit in the xdc csr 105 * [6] <command started> 106 * 107 * when the controller is done with a command it may interrupt (if you 108 * ask it to) and it will set the XDC_REMIOPB bit in the csr. the address 109 * of the finished iopb will be in the xdc registers. after that is 110 * read, set the XDC_CLRRIO to clear the iopb out of memory. 111 * 112 * the format of the iopb is described in section 4 of the manual. 113 */ 114 115 struct xd_iopb { 116 /* section 4.1.1: byte 0 */ 117 volatile u_char errs:1; /* error summary bit, only valid if 118 "done" is set. must clear "done" 119 and "errs" bits before starting an 120 operation */ 121 volatile u_char done:1; /* "done" bit */ 122 volatile u_char chen:1; /* chain enable, "next iopb" is valid, 123 note xd returns one iopb at a time */ 124 volatile u_char sgm:1; /* scatter/gather mode */ 125 volatile u_char comm:4; /* command number (see table 4-2) */ 126 #define XDCMD_NOP 0x0 /* no-op */ 127 #define XDCMD_WR 0x1 /* write */ 128 #define XDCMD_RD 0x2 /* read */ 129 #define XDCMD_SK 0x3 /* seek */ 130 #define XDCMD_RST 0x4 /* drive reset */ 131 #define XDCMD_WRP 0x5 /* write params */ 132 #define XDCMD_RDP 0x6 /* read params */ 133 #define XDCMD_XWR 0x7 /* extended write */ 134 #define XDCMD_XRD 0x8 /* extended read */ 135 #define XDCMD_TST 0x9 /* diagnostic tests */ 136 /* 0xa to 0xf are reserved */ 137 /* section 4.1.2: byte 1 */ 138 volatile u_char errno; /* status byte 1 (non-zero if error) */ 139 /* section 4.1.3: byte 2 */ 140 volatile u_char status; /* status byte 2 (see below) */ 141 #define XDST_SR 0x40 /* slipped revolution */ 142 #define XDST_CSE 0x20 /* count sectors executed */ 143 #define XDST_WRPT 0x10 /* write protected drive */ 144 #define XDST_DFLT 0x08 /* disk fault */ 145 #define XDST_SKER 0x04 /* seek error: >max, or timeout */ 146 #define XDST_ONCL 0x02 /* on-cylinder */ 147 #define XDST_DRDY 0x01 /* drive is ready! */ 148 /* section 4.1.4: byte 3 */ 149 volatile u_char istat; /* internal status: reserved for xylogics */ 150 /* section 4.1.5: byte 4 */ 151 volatile u_char subfun; /* sub-function of command (see below) */ 152 #define XDFUN_R 0x00 /* XDCMD_SK: report current addr */ 153 #define XDFUN_SR 0x01 /* XDCMD_SK: seek and report addr */ 154 #define XDFUN_SRI 0x02 /* XDCMD_SK: start seek, report comp imm */ 155 #define XDFUN_CTL 0x00 /* XDCMD_{WRP,RDP}: controller params */ 156 #define XDFUN_DRV 0x80 /* XDCMD_{WRP,RDP}: drive params */ 157 #define XDFUN_FMT 0x81 /* XDCMD_{WRP,RDP}: format params,XWR form.*/ 158 #define XDFUN_STX 0xa0 /* XDCMD_RDP: read drive status extended */ 159 #define XDFUN_THD 0x80 /* XDCMD_{XWR,XRD}: track headers */ 160 #define XDFUN_VFY 0x81 /* XDCMD_XRD: verify data */ 161 #define XDFUN_HDR 0x82 /* XDCMD_{XWR,XRD}: header, verify,data, ecc*/ 162 #define XDFUN_DM 0xa0 /* XDCMD_{XWR,XRD}: defect map */ 163 #define XDFUN_DMX 0xa1 /* XDCMD_{XWR,XRD}: defect map extended */ 164 /* section 4.1.6: byte 5 */ 165 volatile u_char fixd:1; /* fixed media (vs removable) */ 166 volatile u_char reserved1:4; /* reserved */ 167 volatile u_char unit:3; /* unit number */ 168 /* note: 6 to 13 are overloaded (see below) */ 169 /* section 4.1.7: byte 6 */ 170 volatile u_char lll:5; /* linked list length */ 171 volatile u_char intl:3; /* interrupt level */ 172 /* section 4.1.8: byte 7 */ 173 volatile u_char intr_vec; /* interrupt vector */ 174 /* section 4.1.9: bytes 8 and 9 */ 175 volatile u_short sectcnt; /* sector count (# to xfer) */ 176 /* section 4.1.10: byte a and b */ 177 volatile u_short cylno; /* cylinder number */ 178 /* section 4.1.11: byte c */ 179 volatile u_char headno; /* head number */ 180 /* section 4.1.12: byte d */ 181 volatile u_char sectno; /* sector number */ 182 /* section 4.1.13: byte e */ 183 volatile u_char addrmod; /* addr modifier (bits 7,6 must be zero) */ 184 /* section 4.1.14: byte f */ 185 volatile u_char naddrmod; /* next (in chain) address iobp ad. modifer */ 186 /* section 4.1.15: bytes 0x10 to 0x13 */ 187 volatile u_long daddr; /* DMA data address */ 188 /* section 4.1.16: bytes 0x14 to 0x17 */ 189 volatile u_long nextiopb; /* next iopb (in chain) address */ 190 /* section 4.1.17: bytes 0x18, 0x19 */ 191 volatile u_short cksum; /* iopb checksum */ 192 /* section 4.1.18: bytes 0x1a, 0x1b */ 193 volatile u_short eccpattern; /* ECC pattern word (ecc mode 0) */ 194 /* section 4.1.19: bytes 0x1c, 0x1d */ 195 volatile u_short eccoffword; /* ECC offset word (ecc mode 0) */ 196 }; 197 198 /* 199 * some commands overload bytes 6 to 0x13 of the iopb with different meanings. 200 * these commands include: 201 * section 4.2: controller parameters 202 * section 4.3: drive parameters 203 * sectino 4.4: format parameters 204 * 205 * note that the commands that overload the iopb are not part of the 206 * "critical data path" of the driver. so, we handle them by defining 207 * alternate iopb structures for these commands... it only costs us an 208 * extra pointer. 209 */ 210 211 /* 212 * controller parameters iopb: redefines bytes: 8 -> 0xe, 0x10 -> 0x13 213 */ 214 215 struct xd_iopb_ctrl { 216 volatile u_char same[8]; /* same as xd_iopb */ 217 /* section 4.2.1: byte 8 */ 218 volatile u_char param_a; /* param A (see below) */ 219 #define XDPA_AUD 0x80 /* auto-update iopb fields when cmd done */ 220 #define XDPA_TMOD 0x40 /* long-word transfer mode (vs word) */ 221 #define XDPA_DACF 0x20 /* ignore vme ACFAIL signal */ 222 #define XDPA_ICS 0x10 /* checksum check (adds 100usec per xfer) */ 223 #define XDPA_EDT 0x08 /* enable on-board DMA timeout timer */ 224 #define XDPA_NPRM 0x04 /* enable VME non-priv request mode */ 225 /* rest must be zero */ 226 /* section 4.2.2: byte 9 */ 227 volatile u_char param_b; /* param B (see below) */ 228 #define XDPB_TDT 0xc0 /* throttle dead time (see 8.11, below) */ 229 #define XDPB_ROR 0x10 /* release on request */ 230 #define XDPB_DRA 0x01 /* disable read ahead */ 231 /* TDT values: */ 232 #define XDPB_TDT_0USEC 0x00 /* no TDT */ 233 #define XDPB_TDT_3_2USEC 0x40 /* 3.2 usec */ 234 #define XDPB_TDT_6_4USEC 0x80 /* 6.4 usec */ 235 #define XDPB_TDT_12_8USEC 0xc0 /* 12.8 usec */ 236 /* section 4.2.3: byte a */ 237 volatile u_char param_c; /* param C (see below) */ 238 #define XDPC_OVS 0x80 /* over-lapped seek */ 239 #define XDPC_COP 0x40 /* command optimiziation (elevator alg.) */ 240 #define XDPC_ASR 0x10 /* auto-seek retry */ 241 #define XDPC_RBC 0x04 /* retry before correction if ECC error */ 242 #define XDPC_ECCM 0x03 /* ECC mode (0, 1, and 2) */ 243 #define XDPC_ECC0 0x00 /* ECC mode 0 */ 244 #define XDPC_ECC1 0x01 /* ECC mode 1 */ 245 #define XDPC_ECC2 0x02 /* ECC mode 2 */ 246 /* section 4.2.4: byte b */ 247 volatile u_char throttle; /* max DMA xfers per master (0==256) */ 248 /* section 4.2.5: byte c */ 249 volatile u_char eprom_lvl; /* EPROM release level */ 250 volatile u_char delay; /* delay (see note below) */ 251 /* section 4.2.6: byte e */ 252 volatile u_char ctype; /* controller type */ 253 #define XDCT_753 0x53 /* xylogic 753/7053 */ 254 volatile u_char same2; /* byte f: same as xd_iopb */ 255 /* section 4.2.7: byte 0x10, 0x11 */ 256 volatile u_short eprom_partno; /* eprom part number */ 257 /* section 4.2.8: byte 12 */ 258 volatile u_char eprom_rev; /* eprom revision number */ 259 }; 260 261 /* 262 * Note on byte 0xd ("delay"): This byte is not documented in the 263 * Xylogics manual. However, I contacted Xylogics and found out what 264 * it does. The controller sorts read commands into groups of 265 * contiguous sectors. After it processes a group of contiguous 266 * sectors rather than immediately going on to the next group of 267 * contiguous sectors, the controller can delay for a certain amount 268 * of time in hopes of getting another cluster of reads in the same 269 * area of the disk (thus avoiding a long seek). Byte 0xd controls 270 * how long it waits before giving up and going on and doing the next 271 * contiguous cluster. 272 * 273 * it is unclear what unit the delay is in, but it looks like sun 274 * uses the value "20" for sun3's, and "0" for sparc, except for the 275 * 4/300 (where it is "4"). [see /sys/sundev/xd_conf.c on any 4.1.3 276 * machine for how sun configures its controller...] 277 */ 278 279 #define XDC_DELAY_SUN3 20 280 #define XDC_DELAY_4_300 4 281 #define XDC_DELAY_SPARC 0 282 283 /* 284 * drive parameters iopb: redefines bytes: 6, 8, 9, a, b, c, d, e 285 */ 286 287 struct xd_iopb_drive { 288 volatile u_char same[6]; /* same as xd_iopb */ 289 /* section 4.3.1: byte 6 */ 290 volatile u_char dparam_ipl; /* drive params | interrupt level */ 291 #define XDDP_EC32 0x10 /* 32 bit ECC mode */ 292 volatile u_char same1; /* byte 7: same */ 293 /* section 4.3.2: byte 8 */ 294 volatile u_char maxsect; /* max sector/last head (<= byte d) */ 295 /* section 4.3.3: byte 9 */ 296 volatile u_char headoff; /* head offset */ 297 /* section 4.3.4: bytes 0xa, 0xb */ 298 volatile u_short maxcyl; /* max cyl (zero based!) */ 299 /* section 4.3.5: byte 0xc */ 300 volatile u_char maxhead; /* max head (zero based!) */ 301 /* section 4.3.6: byte 0xd */ 302 volatile u_char maxsector; /* max sector of disk (zero based!) */ 303 /* section 4.3.7: byte 0xe */ 304 volatile u_char sectpertrk; /* sectors per track, not zero base, no runt*/ 305 }; 306 307 /* 308 * format parameters iopb: redefines bytes: 6, 8, 9, a, b, c, d, 0x10, 0x11 309 */ 310 311 struct xd_iopb_format { 312 volatile u_char same[6]; /* smae as xd_iopb */ 313 /* section 4.4.1: byte 6 */ 314 volatile u_char interleave_ipl;/* (interleave << 4) | interrupt level */ 315 /* interleave ratio 1:1 to 16:1 */ 316 volatile u_char same1; /* byte 7: same */ 317 /* section 4.4.2: byte 8 */ 318 volatile u_char field1; /* >= 1, xylogic says should be 1 */ 319 #define XDFM_FIELD1 0x01 /* xylogic value */ 320 /* section 4.4.3: byte 9 */ 321 volatile u_char field2; /* >0, field1+field2 <= 255 */ 322 #define XDFM_FIELD2 0x0a /* xylogic value */ 323 /* section 4.4.4: byte a */ 324 volatile u_char field3; /* >= field1+field2 */ 325 #define XDFM_FIELD3 0x1b /* xylogic value */ 326 /* section 4.4.5: byte b */ 327 volatile u_char field4; /* field4 */ 328 #define XDFM_FIELD4 0x14 /* xylogic value */ 329 /* section 4.4.6: bytes 0xc, 0xd */ 330 volatile u_short bytespersec; /* bytes per sector */ 331 #define XDFM_BPS 0x200 /* must be 512! */ 332 volatile u_char same2[2]; /* bytes e, f */ 333 /* section 4.4.7: byte 0x10 */ 334 volatile u_char field6; /* field 6 */ 335 #define XDFM_FIELD6 0x0a /* xylogic value */ 336 /* section 4.4.8: byte 0x11 */ 337 volatile u_char field7; /* field 7, >= 1 */ 338 #define XDFM_FIELD7 0x03 /* xylogic value */ 339 }; 340 341 342 /* 343 * errors: errors come from either the fatal error register or the 344 * iopb 345 */ 346 347 #define XD_ERA_MASK 0xf0 /* error action mask */ 348 #define XD_ERA_PROG 0x10 /* program error */ 349 #define XD_ERA_PRG2 0x20 /* program error */ 350 #define XD_ERA_SOFT 0x30 /* soft error: we recovered */ 351 #define XD_ERA_HARD 0x40 /* hard error: retry */ 352 #define XD_ERA_RSET 0x60 /* hard error: reset, then retry */ 353 #define XD_ERA_WPRO 0x90 /* write protected */ 354 355 /* software error codes */ 356 #define XD_ERR_FAIL 0xff /* general total failure */ 357 /* no error */ 358 #define XD_ERR_AOK 0x00 /* success */ 359 /* non-retryable programming error */ 360 #define XD_ERR_ICYL 0x10 /* illegal cyl */ 361 #define XD_ERR_IHD 0x11 /* illegal head */ 362 #define XD_ERR_ISEC 0x12 /* illegal sector */ 363 #define XD_ERR_CZER 0x13 /* count zero */ 364 #define XD_ERR_UIMP 0x14 /* unknown command */ 365 #define XD_ERR_IF1 0x15 /* illegal field 1 */ 366 #define XD_ERR_IF2 0x16 /* illegal field 2 */ 367 #define XD_ERR_IF3 0x17 /* illegal field 3 */ 368 #define XD_ERR_IF4 0x18 /* illegal field 4 */ 369 #define XD_ERR_IF5 0x19 /* illegal field 5 */ 370 #define XD_ERR_IF6 0x1a /* illegal field 6 */ 371 #define XD_ERR_IF7 0x1b /* illegal field 7 */ 372 #define XD_ERR_ISG 0x1c /* illegal scatter/gather */ 373 #define XD_ERR_ISPT 0x1d /* not enough sectors per track */ 374 #define XD_ERR_ALGN 0x1e /* next iopb allignment error */ 375 #define XD_ERR_SGAL 0x1f /* scatter gather address alignment error */ 376 #define XD_ERR_SGEC 0x20 /* scatter gather with auto ECC */ 377 /* successfully recovered soft errors */ 378 #define XD_ERR_SECC 0x30 /* soft ecc corrected */ 379 #define XD_ERR_SIGN 0x31 /* ecc ignored */ 380 #define XD_ERR_ASEK 0x32 /* auto-seek retry recovered */ 381 #define XD_ERR_RTRY 0x33 /* soft retry recovered */ 382 /* hard errors: please retry */ 383 #define XD_ERR_HECC 0x40 /* hard data ECC */ 384 #define XD_ERR_NHDR 0x41 /* header not found */ 385 #define XD_ERR_NRDY 0x42 /* drive not ready */ 386 #define XD_ERR_TOUT 0x43 /* timeout */ 387 #define XD_ERR_VTIM 0x44 /* VME DMA timeout */ 388 #define XD_ERR_DSEQ 0x45 /* disk sequencer error */ 389 #define XD_ERR_HDEC 0x48 /* header ECC error */ 390 #define XD_ERR_RVFY 0x49 /* ready verify */ 391 #define XD_ERR_VFER 0x4a /* fatal VME DMA error */ 392 #define XD_ERR_VBUS 0x4b /* VME bus error */ 393 /* hard error: reset and retry */ 394 #define XD_ERR_DFLT 0x60 /* drive fault */ 395 #define XD_ERR_HECY 0x61 /* header error/cyl */ 396 #define XD_ERR_HEHD 0x62 /* header error/head */ 397 #define XD_ERR_NOCY 0x63 /* not on cylinder */ 398 #define XD_ERR_SEEK 0x64 /* seek error */ 399 /* fatal hardware error */ 400 #define XD_ERR_ILSS 0x70 /* illegal sector size */ 401 /* misc */ 402 #define XD_ERR_SEC 0x80 /* soft ecc */ 403 /* requires manual intervention */ 404 #define XD_ERR_WPER 0x90 /* write protected */ 405 /* FATAL errors */ 406 #define XD_ERR_IRAM 0xe1 /* IRAM self test failed */ 407 #define XD_ERR_MT3 0xe3 /* maint test 3 failed (DSKCEL RAM) */ 408 #define XD_ERR_MT4 0xe4 /* maint test 4 failed (Header shift reg) */ 409 #define XD_ERR_MT5 0xe5 /* maint test 5 failed (VMEDMA regs) */ 410 #define XD_ERR_MT6 0xe6 /* maint test 6 failed (REGCEL chip) */ 411 #define XD_ERR_MT7 0xe7 /* maint test 7 failed (buff. parity) */ 412 #define XD_ERR_MT8 0xe8 /* maint test 8 failed (fifo) */ 413 #define XD_ERR_IOCK 0xf0 /* iopb checksume miscompare */ 414 #define XD_ERR_IODM 0xf1 /* iopb DMA fatal */ 415 #define XD_ERR_IOAL 0xf2 /* iopb allignment error */ 416 #define XD_ERR_FIRM 0xf3 /* firmware error n*/ 417 #define XD_ERR_MMOD 0xf5 /* illegal maint mode test number */ 418 #define XD_ERR_ACFL 0xf6 /* ACFAIL asserted */ 419
Indexes created Tue Oct 14 11:09:46 GMT 2025