GENERIC revision 1.28
1 # $NetBSD: GENERIC,v 1.28 1999/03/16 16:30:16 minoura Exp $ 2 3 # 4 # GENERIC 5 # 6 7 include "arch/x68k/conf/std.x68k" 8 9 maxusers 32 10 11 ## System kernel configuration. See options(4) for more detail. 12 13 14 ## Options for variants of the m68k MPU 15 ## you must have at least the correct one; REQUIRED 16 options M68030 17 options M68040 18 options M68060 19 20 21 #### System options specific to the x68k port 22 23 options UVM # new virtual memory system 24 options MACHINE_NONCONTIG # support for noncontiguous memory 25 options FPU_EMULATE # software fpu emulation for MC68030 26 options FPSP # floating point emulation for MC68040 27 options M060SP # int/fp emulation for MC68060 28 options JUPITER # support for "Jupiter-X" accelerator 29 options MAPPEDCOPY # use page mapping for large copyin/copyout 30 #options ZSCONSOLE,ZSCN_SPEED="9600" # use serial console 31 32 33 #### System options that are the same for all ports 34 35 ## Root device configuration: change the ?'s if you are going to use a 36 ## nonstandard root partition (other than where the kernel is booted from) 37 ## and/or nonstandard root type (not ffs or nfs). Normally this can be 38 ## automagically determined at boot time. 39 40 config netbsd root on ? type ? 41 #config netbsd root on sd0 type ffs 42 43 ## RTC is offset from GMT; -540 means JST-9 44 options RTC_OFFSET=-540 # hardware clock is this many mins. west of GMT 45 46 ## System call tracing (see ktrace(1)). 47 options KTRACE 48 49 ## Collect statistics on kernel malloc's and free's. This does have a 50 ## significant performance hit on slower machines, so it is intended for 51 ## diagnostic use only. 52 #options KMEMSTATS 53 54 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 55 options SYSVMSG # System V message queues 56 options SYSVSEM # System V semaphores 57 options SYSVSHM # System V shared memory 58 #options SHMMAXPGS=1024 # 1024 pages is the default 59 60 ## Loadable kernel module support 61 #options LKM 62 63 ## NFS boot options; not supported currently: needs nfsboot program 64 #options NFS_BOOT_BOOTPARAM 65 #options NFS_BOOT_BOOTP 66 #options NFS_BOOT_DHCP 67 68 #### Debugging options 69 70 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 71 ## serial console break or keyboard reset, where the PROM would normally 72 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 73 #options DDB # kernel dynamic debugger 74 #options DDB_HISTORY_SIZE=100 # enable history editing in DDB 75 #options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 76 #options PANICBUTTON # interrupt switch invokes DDB 77 78 ## You may also use gdb, on another computer connected to this machine over 79 ## a serial port. Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is 80 ## a dev_t encoded device number of the serial port to use. 81 ## KGDB is not supported for now. 82 #options KGDB # support for kernel gdb 83 #options KGDBDEV=0xc00 # kgdb device number 84 #options KGDBRATE=9600 # baud rate 85 86 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 87 ## such that gdb(1) can be used on a kernel coredump. 88 89 #makeoptions DEBUG="-g" 90 91 ## Adds code to the kernel that does internal consistency checks, and will 92 ## cause the kernel to panic if corruption of internal data structures 93 ## is detected. 94 #options DIAGNOSTIC # extra kernel sanity checking 95 96 ## Enable (possibly expensive) debugging code that may also display messages 97 ## on the system console 98 #options DEBUG 99 100 ## Make SCSI error messages more verbose when explaining their meanings. 101 options SCSIVERBOSE 102 103 ## `INSECURE' turns off the kernel security level (securelevel = 0 always). 104 ## This allows writing to /dev/mem, loading kernel modules while multi-user, 105 ## and other insecurities good only for development work. Do not use this 106 ## option on a production machine. 107 #options INSECURE 108 109 ## Allow non-root users to grab /dev/console with programs such as xconsole. 110 ## `xconsole' therefore does not need setuid root with this option enabled. 111 #options UCONSOLE 112 113 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a 114 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 115 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 116 ## opaque file mechanism. Perl calls this "secure setuid scripts." 117 118 #options FDSCRIPTS 119 #options SETUIDSCRIPTS 120 121 ## Options for compatibility with previous releases foreign system binaries. 122 123 options COMPAT_43 # 4.3BSD system interfaces 124 options COMPAT_09 # NetBSD 0.9 binary compatibility 125 options COMPAT_10 # NetBSD 1.0 binary compatibility 126 options COMPAT_11 # NetBSD 1.1 binary compatibility 127 options COMPAT_12 # NetBSD 1.2 binary compatibility 128 options COMPAT_13 # NetBSD 1.3 binary compatibility 129 #options COMPAT_M68K4K # NetBSD/m68k4k binaries 130 #options COMPAT_SUNOS # SunOS 4.x binary compatibility; broken 131 #options COMPAT_LINUX # Linux/m68k binary compatibility 132 #options EXEC_ELF32 # 32-bit ELF executables (Linux) 133 134 ## File systems. 135 file-system FFS # Berkeley Fast Filesystem 136 file-system NFS # Sun NFS-compatible filesystem client 137 file-system KERNFS # kernel data-structure filesystem 138 file-system NULLFS # NULL layered filesystem 139 file-system MFS # memory-based filesystem 140 #file-system FDESC # user file descriptor filesystem 141 file-system UMAPFS # uid/gid remapping filesystem 142 #file-system LFS # Log-based filesystem (still experimental) 143 file-system PORTAL # portal filesystem (still experimental) 144 file-system PROCFS # /proc 145 file-system CD9660 # ISO 9660 + Rock Ridge file system 146 file-system UNION # union file system 147 file-system MSDOSFS # MS-DOS FAT filesystem(s). 148 #file-system ADOSFS # AmigaDOS filesystem 149 150 ## File system options. 151 options NFSSERVER # Sun NFS-compatible filesystem server 152 options QUOTA # FFS quotas 153 #options FFS_EI # FFS Endian Independent support 154 155 ## Network protocol support. In most environments, INET is required. 156 options INET # IP (Internet Protocol) v4 157 options TCP_COMPAT_42 # 4.2BSD IP implementation compatibility 158 #options GATEWAY # packet forwarding ("router switch") 159 #options MROUTING # packet forwarding of multicast packets 160 #options DIRECTED_BROADCAST # allow broadcasts through routers 161 #options NS # Xerox NS networking 162 #options NSIP # Xerox NS tunneling over IP 163 #options ISO,TPIP # OSI networking 164 #options EON # OSI tunneling over IP 165 #options CCITT,LLC,HDLC # X.25 packet switched protocol 166 options NETATALK # AppleTalk (over Ethernet) protocol 167 options NTP # Network Time Protocol in-kernel support 168 #options PPS_SYNC # Add serial line synchronization for NTP 169 #options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 170 options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 171 #options PPP_BSDCOMP # Add BSD compression to ppp device 172 #options PPP_DEFLATE # Add deflate (libz) compression to ppp device 173 #options PPP_FILTER # Add active filters for ppp (via bpf) 174 175 176 177 #### Device configurations 178 179 ## Fundamental devices; see also std.x68k 180 dmac0 at intio0 addr 0xe84000 # DMA controler 181 xel0 at intio0 182 opm0 at intio0 addr 0xe90000 # OPM: required for fdc 183 184 ## Display devices and console 185 grfbus0 at mainbus0 # bitmapped displays 186 grf0 at grfbus0 # multiplane graphics 187 grf1 at grfbus0 # flexible graphics 188 189 kbd0 at mfp0 # standard keyboard 190 ite0 at grf0 # internal terminal emulator 191 #options ITE_KERNEL_ATTR=4 # bold for kernel messages 192 # see /sys/arch/x68k/dev/itevar.h 193 #!pow0 at mfp0 flags 0 # power switch status; intr enabled 194 #!pow1 at mfp0 flags 1 # power switch status; read only 195 pseudo-device pow 2 #! software power switch 196 197 ## floppy disks 198 fdc0 at intio0 addr 0xe94000 intr 96 dma 0 dmaintr 100 # floppy controler 199 fd* at fdc0 unit ? # builtin floppy drives 200 201 ## SCSI devices 202 scsirom0 at intio0 addr 0xfc0000 # Built-in SCSI BIOS 203 scsirom1 at intio0 addr 0xea0020 # External SCSI BIOS 204 spc0 at scsirom0 # genuin SCSI 205 spc1 at scsirom1 # genuin SCSI 206 scsibus* at spc? 207 mha0 at scsirom1 # Mankai MK-HA1 (Mach-2) 208 scsibus* at mha0 209 210 sd* at scsibus? target ? lun ? # SCSI disks 211 cd* at scsibus? target ? lun ? # SCSI CD-ROMs 212 st* at scsibus? target ? lun ? # SCSI tapes 213 #ss* at scsibus? target ? lun ? # SCSI scanners 214 ch* at scsibus? target ? lun ? # SCSI changer devices 215 #uk* at scsibus? target ? lun ? # SCSI unknown devices 216 217 ## Serial ports 218 zsc0 at intio0 addr 0xe98000 intr 112 219 zstty0 at zsc0 channel 0 # built-in RS-232C 220 ms0 at zsc0 channel 1 # standard mouse 221 #zsc1 at intio0 addr 0xeafc00 intr 113 222 #zstty2 at zsc1 channel 0 223 #zstty3 at zsc1 channel 1 224 #zsc2 at intio0 addr 0xeafc10 intr 114 225 #zstty4 at zsc2 channel 0 226 #zstty5 at zsc2 channel 1 227 228 pseudo-device sram #! battery-backuped static RAM 229 pseudo-device bell #! OPM bell 230 231 xcom0 at mainbus0 # NS16550 fast serial 232 xcom1 at mainbus0 233 234 ## Audio device 235 #okiadpcm0 at intio0 addr 0xe92000 intr 106 errintr 107 dma 3 236 #audio* at okiadpcm* 237 238 ## Network interfaces 239 neptune0 at intio0 addr 0xece000 intr 249 # Neptune-X 240 neptune1 at intio0 addr 0xece400 intr 249 # Neptune-X at alt. addr. 241 ne0 at neptune? addr 0x300 # NE2000 or clone 242 #se0 at scsibus? target ? lun ? # Ether+; not supported 243 244 245 #### Pseudo devices 246 247 ## A disk-like interface to files. Can be used to create floppy, CD, 248 ## miniroot images, etc. 249 250 pseudo-device vnd 4 251 252 ## Concatenated and striped disks; with this, you can create a software-based 253 ## disk array similar to a "RAID 0" setup. See ccd(4). 254 255 #pseudo-device ccd 4 256 257 ## RAIDframe disk driver: software RAID driver. See raid(4). 258 259 #pseudo-device raid 4 260 261 ## Memory disk device, used on boot floppies with compressed 262 ## kernel-plus-root-disk images. 263 264 #pseudo-device md 1 265 266 ## Loopback network interface; required 267 pseudo-device loop 268 269 ## SLIP and CSLIP interfaces, for IP over a serial line. 270 pseudo-device sl 1 271 272 ## PPP, the successor to SLIP. See pppd(8). 273 pseudo-device ppp 1 274 275 ## Network "tunnel" device, allowing protocol stacks to run in the userland. 276 ## This is used by the third-party user-mode "ppp" program, and others. 277 pseudo-device tun 4 278 279 ## Generic L3 over IP tunnel 280 #pseudo-device gre 2 # generic L3 over IP tunnel 281 282 ## Berkeley Packet Filter, required to run RARPD. A generic C-language 283 ## interface that allows selective examining of incoming packets. 284 pseudo-device bpfilter 8 285 286 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for 287 ## one example of the use of the IP Filter. 288 pseudo-device ipfilter 289 290 291 #### Other device configuration 292 293 ## Pseudo ttys, required for network logins and programs like screen. 294 ## 32 is a good number for average systems; you may have as many as you 295 ## like, though 256 is more or less the upper limit. Increasing this 296 ## number still requires you to run /dev/MAKEDEV to create the files 297 ## for the ptys. 298 299 pseudo-device pty 32 # pseudo-ttys (for network, etc.) 300 301 ## Random device, used to implement /dev/random (a source of random noise), 302 ## and generate randomness for some kernel formulae. 303 ## THIS DEVICE IS EXPERIMENTAL; use at your own risk. 304 305 #pseudo-device rnd 306
Indexes created Tue Oct 14 21:09:58 GMT 2025