GENERIC revision 1.36
1 # $NetBSD: GENERIC,v 1.36 1999/07/29 10:37:25 augustss Exp $ 2 3 # 4 # GENERIC 5 # 6 7 include "arch/x68k/conf/std.x68k" 8 9 maxusers 32 10 11 ## System kernel configuration. See options(4) for more detail. 12 13 14 ## Options for variants of the m68k MPU 15 ## you must have at least the correct one; REQUIRED 16 options M68030 17 options M68040 18 options M68060 19 20 21 #### System options specific to the x68k port 22 23 options EXTENDED_MEMORY # support for >16MB memory 24 options FPU_EMULATE # software fpu emulation for MC68030 25 options FPSP # floating point emulation for MC68040 26 options M060SP # int/fp emulation for MC68060 27 options JUPITER # support for "Jupiter-X" accelerator 28 options MAPPEDCOPY # use page mapping for large copyin/copyout 29 #options ZSCONSOLE,ZSCN_SPEED="9600" # use serial console 30 31 32 #### System options that are the same for all ports 33 34 ## Root device configuration: change the ?'s if you are going to use a 35 ## nonstandard root partition (other than where the kernel is booted from) 36 ## and/or nonstandard root type (not ffs or nfs). Normally this can be 37 ## automagically determined at boot time. 38 39 config netbsd root on ? type ? 40 #config netbsd root on sd0 type ffs 41 42 ## RTC is offset from GMT; -540 means JST-9 43 options RTC_OFFSET=-540 # hardware clock is this many mins. west of GMT 44 45 ## System call tracing (see ktrace(1)). 46 options KTRACE 47 48 ## Collect statistics on kernel malloc's and free's. This does have a 49 ## significant performance hit on slower machines, so it is intended for 50 ## diagnostic use only. 51 #options KMEMSTATS 52 53 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 54 options SYSVMSG # System V message queues 55 options SYSVSEM # System V semaphores 56 options SYSVSHM # System V shared memory 57 #options SHMMAXPGS=1024 # 1024 pages is the default 58 59 ## Loadable kernel module support 60 #options LKM 61 62 ## NFS boot options; not supported currently: needs nfsboot program 63 #options NFS_BOOT_BOOTPARAM 64 #options NFS_BOOT_BOOTP 65 #options NFS_BOOT_DHCP 66 67 #### Debugging options 68 69 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 70 ## serial console break or keyboard reset, where the PROM would normally 71 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 72 #options DDB # kernel dynamic debugger 73 #options DDB_HISTORY_SIZE=100 # enable history editing in DDB 74 #options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 75 #options PANICBUTTON # interrupt switch invokes DDB 76 77 ## You may also use gdb, on another computer connected to this machine over 78 ## a serial port. Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is 79 ## a dev_t encoded device number of the serial port to use. 80 ## KGDB is not supported for now. 81 #options KGDB # support for kernel gdb 82 #options KGDBDEV=0xc00 # kgdb device number 83 #options KGDBRATE=9600 # baud rate 84 85 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 86 ## such that gdb(1) can be used on a kernel coredump. 87 88 #makeoptions DEBUG="-g" 89 90 ## Adds code to the kernel that does internal consistency checks, and will 91 ## cause the kernel to panic if corruption of internal data structures 92 ## is detected. 93 #options DIAGNOSTIC # extra kernel sanity checking 94 95 ## Enable (possibly expensive) debugging code that may also display messages 96 ## on the system console 97 #options DEBUG 98 99 ## Make SCSI error messages more verbose when explaining their meanings. 100 options SCSIVERBOSE 101 102 ## `INSECURE' turns off the kernel security level (securelevel = 0 always). 103 ## This allows writing to /dev/mem, loading kernel modules while multi-user, 104 ## and other insecurities good only for development work. Do not use this 105 ## option on a production machine. 106 #options INSECURE 107 108 ## Allow non-root users to grab /dev/console with programs such as xconsole. 109 ## `xconsole' therefore does not need setuid root with this option enabled. 110 #options UCONSOLE 111 112 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a 113 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 114 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 115 ## opaque file mechanism. Perl calls this "secure setuid scripts." 116 117 #options FDSCRIPTS 118 #options SETUIDSCRIPTS 119 120 ## Options for compatibility with previous releases foreign system binaries. 121 122 options COMPAT_43 # 4.3BSD system interfaces 123 options COMPAT_09 # NetBSD 0.9 binary compatibility 124 options COMPAT_10 # NetBSD 1.0 binary compatibility 125 options COMPAT_11 # NetBSD 1.1 binary compatibility 126 options COMPAT_12 # NetBSD 1.2 binary compatibility 127 options COMPAT_13 # NetBSD 1.3 binary compatibility 128 options COMPAT_14 # NetBSD 1.4 binary compatibility 129 #options COMPAT_M68K4K # NetBSD/m68k4k binaries 130 #options COMPAT_SUNOS # SunOS 4.x binary compatibility; broken 131 #options COMPAT_SVR4 # SVR4 binary compatibility; broken 132 #options COMPAT_LINUX # Linux/m68k binary compatibility 133 #options EXEC_ELF32 # 32-bit ELF executables (Linux, SVR4) 134 135 ## File systems. 136 file-system FFS # Berkeley Fast Filesystem 137 file-system NFS # Sun NFS-compatible filesystem client 138 file-system KERNFS # kernel data-structure filesystem 139 #file-system NULLFS # NULL layered filesystem (buggy) 140 file-system MFS # memory-based filesystem 141 #file-system FDESC # user file descriptor filesystem 142 file-system UMAPFS # uid/gid remapping filesystem 143 #file-system LFS # Log-structured filesystem (experimental) 144 #file-system PORTAL # portal filesystem (experimental) 145 file-system PROCFS # /proc 146 file-system CD9660 # ISO 9660 + Rock Ridge file system 147 #file-system UNION # union file system (a little buggy) 148 file-system MSDOSFS # MS-DOS FAT filesystem(s). 149 #file-system ADOSFS # AmigaDOS filesystem 150 151 ## File system options. 152 options NFSSERVER # Sun NFS-compatible filesystem server 153 options QUOTA # FFS quotas 154 #options FFS_EI # FFS Endian Independent support 155 156 ## Network protocol support. In most environments, INET is required. 157 options INET # IP (Internet Protocol) v4 158 options TCP_COMPAT_42 # 4.2BSD IP implementation compatibility 159 #options GATEWAY # packet forwarding ("router switch") 160 #options MROUTING # packet forwarding of multicast packets 161 #options DIRECTED_BROADCAST # allow broadcasts through routers 162 #options NS # Xerox NS networking 163 #options NSIP # Xerox NS tunneling over IP 164 #options ISO,TPIP # OSI networking 165 #options EON # OSI tunneling over IP 166 #options CCITT,LLC,HDLC # X.25 packet switched protocol 167 options NETATALK # AppleTalk (over Ethernet) protocol 168 options NTP # Network Time Protocol in-kernel support 169 #options PPS_SYNC # Add serial line synchronization for NTP 170 options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 171 options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 172 options PPP_BSDCOMP # Add BSD compression to ppp device 173 options PPP_DEFLATE # Add deflate (libz) compression to ppp device 174 options PPP_FILTER # Add active filters for ppp (via bpf) 175 176 177 178 #### Device configurations 179 180 ## Fundamental devices; see also std.x68k 181 dmac0 at intio0 addr 0xe84000 # DMA controler 182 xel0 at intio0 183 opm0 at intio0 addr 0xe90000 # OPM: required for fdc 184 185 ## Display devices and console 186 grfbus0 at mainbus0 # bitmapped displays 187 grf0 at grfbus0 # multiplane graphics 188 grf1 at grfbus0 # flexible graphics 189 190 kbd0 at mfp0 # standard keyboard 191 ite0 at grf0 # internal terminal emulator 192 options ITE_KERNEL_ATTR=4 # bold for kernel messages 193 # see /sys/arch/x68k/dev/itevar.h 194 pseudo-device pow 2 # software power switch 195 196 ## floppy disks 197 fdc0 at intio0 addr 0xe94000 intr 96 dma 0 dmaintr 100 # floppy controler 198 fd* at fdc0 unit ? # builtin floppy drives 199 200 ## SCSI devices 201 scsirom0 at intio0 addr 0xfc0000 # Built-in SCSI BIOS 202 scsirom1 at intio0 addr 0xea0020 # External SCSI BIOS 203 spc0 at scsirom0 # genuin SCSI 204 spc1 at scsirom1 # genuin SCSI 205 scsibus* at spc? 206 mha0 at scsirom1 # Mankai MK-HA1 (Mach-2) 207 scsibus* at mha0 208 209 sd* at scsibus? target ? lun ? # SCSI disks 210 cd* at scsibus? target ? lun ? # SCSI CD-ROMs 211 st* at scsibus? target ? lun ? # SCSI tapes 212 #ss* at scsibus? target ? lun ? # SCSI scanners 213 ch* at scsibus? target ? lun ? # SCSI changer devices 214 #uk* at scsibus? target ? lun ? # SCSI unknown devices 215 216 ## Serial ports 217 zsc0 at intio0 addr 0xe98000 intr 112 218 zstty0 at zsc0 channel 0 # built-in RS-232C 219 ms0 at zsc0 channel 1 # standard mouse 220 #zsc1 at intio0 addr 0xeafc00 intr 113 221 #zstty2 at zsc1 channel 0 222 #zstty3 at zsc1 channel 1 223 #zsc2 at intio0 addr 0xeafc10 intr 114 224 #zstty4 at zsc2 channel 0 225 #zstty5 at zsc2 channel 1 226 227 pseudo-device sram # battery-backuped static RAM 228 pseudo-device bell # OPM bell 229 230 xcom0 at mainbus0 # NS16550 fast serial 231 xcom1 at mainbus0 232 233 par0 at mainbus0 # Builtin printer port 234 235 ## Audio device; broken 236 #okiadpcm0 at intio0 addr 0xe92000 intr 106 errintr 107 dma 3 237 #audio* at okiadpcm* 238 239 ## Network interfaces 240 neptune0 at intio0 addr 0xece000 intr 249 # Neptune-X 241 neptune1 at intio0 addr 0xece400 intr 249 # Neptune-X at alt. addr. 242 ne0 at neptune? addr 0x300 # NE2000 or clone 243 #se0 at scsibus? target ? lun ? # Ether+; broken 244 245 246 #### Pseudo devices 247 248 ## A disk-like interface to files. Can be used to create floppy, CD, 249 ## miniroot images, etc. 250 251 pseudo-device vnd 4 252 253 ## Concatenated and striped disks; with this, you can create a software-based 254 ## disk array similar to a "RAID 0" setup. See ccd(4). 255 256 pseudo-device ccd 4 257 258 ## RAIDframe disk driver: software RAID driver. See raid(4). 259 260 pseudo-device raid 4 261 262 ## Memory disk device, used on boot floppies with compressed 263 ## kernel-plus-root-disk images. 264 265 #pseudo-device md 1 266 267 ## Loopback network interface; required 268 pseudo-device loop 269 270 ## SLIP and CSLIP interfaces, for IP over a serial line. 271 pseudo-device sl 1 272 273 ## PPP, the successor to SLIP. See pppd(8). 274 pseudo-device ppp 1 275 276 ## Network "tunnel" device, allowing protocol stacks to run in the userland. 277 ## This is used by the third-party user-mode "ppp" program, and others. 278 pseudo-device tun 4 279 280 ## Generic L3 over IP tunnel 281 #pseudo-device gre 2 # generic L3 over IP tunnel 282 283 ## Berkeley Packet Filter, required to run RARPD. A generic C-language 284 ## interface that allows selective examining of incoming packets. 285 pseudo-device bpfilter 8 286 287 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for 288 ## one example of the use of the IP Filter. 289 pseudo-device ipfilter 290 291 292 #### Other device configuration 293 294 ## Pseudo ttys, required for network logins and programs like screen. 295 ## 32 is a good number for average systems; you may have as many as you 296 ## like, though 256 is more or less the upper limit. Increasing this 297 ## number still requires you to run /dev/MAKEDEV to create the files 298 ## for the ptys. 299 300 pseudo-device pty 32 # pseudo-ttys (for network, etc.) 301 302 ## Random device, used to implement /dev/random (a source of random noise), 303 ## and generate randomness for some kernel formulae. 304 305 pseudo-device rnd 306
Indexes created Sun Oct 12 20:09:57 GMT 2025