GENERIC revision 1.52
1 # $NetBSD: GENERIC,v 1.52 2000/09/24 15:59:38 jdolecek Exp $ 2 3 # 4 # GENERIC 5 # 6 7 include "arch/x68k/conf/std.x68k" 8 9 #ident "GENERIC-$Revision: 1.52 $" 10 11 maxusers 8 12 13 ## System kernel configuration. See options(4) for more detail. 14 15 16 ## Options for variants of the m68k MPU 17 ## you must have at least the correct one; REQUIRED 18 options M68030 19 options M68040 20 options M68060 21 22 23 #### System options specific to the x68k port 24 25 options EXTENDED_MEMORY # support for >16MB memory 26 options FPU_EMULATE # software fpu emulation for MC68030 27 options FPSP # floating point emulation for MC68040 28 options M060SP # int/fp emulation for MC68060 29 options JUPITER # support for "Jupiter-X" accelerator 30 #options MAPPEDCOPY # use page mapping for large copyin/copyout 31 #options ZSCONSOLE,ZSCN_SPEED="9600" # use serial console 32 33 34 #### System options that are the same for all ports 35 36 ## Root device configuration: change the ?'s if you are going to use a 37 ## nonstandard root partition (other than where the kernel is booted from) 38 ## and/or nonstandard root type (not ffs or nfs). Normally this can be 39 ## automagically determined at boot time. 40 41 config netbsd root on ? type ? 42 #config netbsd root on sd0 type ffs 43 44 ## RTC is offset from GMT; -540 means JST-9 45 options RTC_OFFSET=-540 # hardware clock is this many mins. west of GMT 46 47 ## System call tracing (see ktrace(1)). 48 options KTRACE 49 50 ## Collect statistics on kernel malloc's and free's. This does have a 51 ## significant performance hit on slower machines, so it is intended for 52 ## diagnostic use only. 53 #options KMEMSTATS 54 55 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 56 options SYSVMSG # System V message queues 57 options SYSVSEM # System V semaphores 58 options SYSVSHM # System V shared memory 59 #options SHMMAXPGS=1024 # 1024 pages is the default 60 61 ## Loadable kernel module support 62 #options LKM 63 64 ## NFS boot options; not supported currently: needs nfsboot program 65 #options NFS_BOOT_BOOTPARAM 66 #options NFS_BOOT_BOOTP 67 #options NFS_BOOT_DHCP 68 69 #### Debugging options 70 71 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 72 ## serial console break or keyboard reset, where the PROM would normally 73 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 74 #options DDB # kernel dynamic debugger 75 #options DDB_HISTORY_SIZE=100 # enable history editing in DDB 76 #options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 77 #options PANICBUTTON # interrupt switch invokes DDB 78 79 ## You may also use gdb, on another computer connected to this machine over 80 ## a serial port. Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is 81 ## a dev_t encoded device number of the serial port to use. 82 ## KGDB is not supported for now. 83 #options KGDB # support for kernel gdb 84 #options KGDBDEV=0xc00 # kgdb device number 85 #options KGDBRATE=9600 # baud rate 86 87 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 88 ## such that gdb(1) can be used on a kernel coredump. 89 90 #makeoptions DEBUG="-g" 91 92 ## Adds code to the kernel that does internal consistency checks, and will 93 ## cause the kernel to panic if corruption of internal data structures 94 ## is detected. 95 #options DIAGNOSTIC # extra kernel sanity checking 96 97 ## Enable (possibly expensive) debugging code that may also display messages 98 ## on the system console 99 #options DEBUG 100 101 ## Make SCSI error messages more verbose when explaining their meanings. 102 #options SCSIVERBOSE 103 104 ## `INSECURE' turns off the kernel security level (securelevel = 0 always). 105 ## This allows writing to /dev/mem, loading kernel modules while multi-user, 106 ## and other insecurities good only for development work. Do not use this 107 ## option on a production machine. 108 #options INSECURE 109 110 ## Allow non-root users to grab /dev/console with programs such as xconsole. 111 ## `xconsole' therefore does not need setuid root with this option enabled. 112 #options UCONSOLE 113 114 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a 115 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 116 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 117 ## opaque file mechanism. Perl calls this "secure setuid scripts." 118 119 #options FDSCRIPTS 120 #options SETUIDSCRIPTS 121 122 ## Options for compatibility with previous releases foreign system binaries. 123 124 options COMPAT_43 # 4.3BSD system interfaces 125 options COMPAT_09 # NetBSD 0.9 binary compatibility 126 options COMPAT_10 # NetBSD 1.0 binary compatibility 127 options COMPAT_11 # NetBSD 1.1 binary compatibility 128 options COMPAT_12 # NetBSD 1.2 binary compatibility 129 options COMPAT_13 # NetBSD 1.3 binary compatibility 130 options COMPAT_14 # NetBSD 1.4 binary compatibility 131 #options COMPAT_M68K4K # NetBSD/m68k4k binaries 132 #options COMPAT_SUNOS # SunOS 4.x binary compatibility; broken 133 #options COMPAT_SVR4 # SVR4 binary compatibility; broken 134 #options COMPAT_LINUX # Linux/m68k binary compatibility 135 #options EXEC_ELF32 # 32-bit ELF executables (Linux, SVR4) 136 137 ## File systems. 138 file-system FFS # Berkeley Fast Filesystem 139 file-system NFS # Sun NFS-compatible filesystem client 140 file-system KERNFS # kernel data-structure filesystem 141 #file-system NULLFS # NULL layered filesystem (buggy) 142 #file-system OVERLAY # overlay file system 143 file-system MFS # memory-based filesystem 144 #file-system FDESC # user file descriptor filesystem 145 file-system UMAPFS # uid/gid remapping filesystem 146 #file-system LFS # Log-structured filesystem (experimental) 147 #file-system PORTAL # portal filesystem (experimental) 148 file-system PROCFS # /proc 149 file-system CD9660 # ISO 9660 + Rock Ridge file system 150 #file-system UNION # union file system (a little buggy) 151 file-system MSDOSFS # MS-DOS FAT filesystem(s). 152 #file-system ADOSFS # AmigaDOS filesystem 153 154 ## File system options. 155 options NFSSERVER # Sun NFS-compatible filesystem server 156 #options QUOTA # FFS quotas 157 #options FFS_EI # FFS Endian Independent support 158 options SOFTDEP # FFS soft updates support. 159 160 ## Network protocol support. In most environments, INET is required. 161 options INET # IP (Internet Protocol) v4 162 options INET6 # IPV6 163 #options IPSEC # IP security 164 #options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 165 #options IPSEC_DEBUG # debug for IP security 166 #options TCP_COMPAT_42 # 4.2BSD IP implementation compatibility 167 #options GATEWAY # packet forwarding ("router switch") 168 #options MROUTING # packet forwarding of multicast packets 169 #options DIRECTED_BROADCAST # allow broadcasts through routers 170 #options NS # Xerox NS networking 171 #options NSIP # Xerox NS tunneling over IP 172 #options ISO,TPIP # OSI networking 173 #options EON # OSI tunneling over IP 174 #options CCITT,LLC,HDLC # X.25 packet switched protocol 175 #options NETATALK # AppleTalk (over Ethernet) protocol 176 #options NTP # Network Time Protocol in-kernel support 177 #options PPS_SYNC # Add serial line synchronization for NTP 178 options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 179 #options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 180 #options PPP_BSDCOMP # Add BSD compression to ppp device 181 #options PPP_DEFLATE # Add deflate (libz) compression to ppp device 182 #options PPP_FILTER # Add active filters for ppp (via bpf) 183 184 185 186 #### Device configurations 187 188 ## Fundamental devices; see also std.x68k 189 dmac0 at intio0 addr 0xe84000 # DMA controler 190 xel0 at intio0 191 opm0 at intio0 addr 0xe90000 # OPM: required for fdc 192 193 ## Display devices and console 194 grfbus0 at mainbus0 # bitmapped displays 195 grf0 at grfbus0 # multiplane graphics 196 grf1 at grfbus0 # flexible graphics 197 198 kbd0 at mfp0 # standard keyboard 199 ite0 at grf0 # internal terminal emulator 200 options ITE_KERNEL_ATTR=4 # bold for kernel messages 201 # see /sys/arch/x68k/dev/itevar.h 202 pseudo-device pow 2 # software power switch 203 204 ## floppy disks 205 fdc0 at intio0 addr 0xe94000 intr 96 dma 0 dmaintr 100 # floppy controler 206 fd* at fdc0 unit ? # builtin floppy drives 207 208 ## SCSI devices 209 scsirom0 at intio0 addr 0xfc0000 # Built-in SCSI BIOS 210 scsirom1 at intio0 addr 0xea0020 # External SCSI BIOS 211 spc0 at scsirom0 # genuin SCSI 212 spc1 at scsirom1 # genuin SCSI 213 scsibus* at spc? 214 mha0 at scsirom1 # Mankai MK-HA1 (Mach-2) 215 scsibus* at mha0 216 217 sd* at scsibus? target ? lun ? # SCSI disks 218 cd* at scsibus? target ? lun ? # SCSI CD-ROMs 219 #st* at scsibus? target ? lun ? # SCSI tapes 220 #ss* at scsibus? target ? lun ? # SCSI scanners 221 #ch* at scsibus? target ? lun ? # SCSI changer devices 222 #uk* at scsibus? target ? lun ? # SCSI unknown devices 223 224 ## Ports 225 zsc0 at intio0 addr 0xe98000 intr 112 226 zstty0 at zsc0 channel 0 # built-in RS-232C 227 ms0 at zsc0 channel 1 # standard mouse 228 #zsc1 at intio0 addr 0xeafc00 intr 113 229 #zstty2 at zsc1 channel 0 230 #zstty3 at zsc1 channel 1 231 #zsc2 at intio0 addr 0xeafc10 intr 114 232 #zstty4 at zsc2 channel 0 233 #zstty5 at zsc2 channel 1 234 par0 at intio0 addr 0xe8c000 # Builtin printer port 235 236 pseudo-device sram # battery-backuped static RAM 237 pseudo-device bell # OPM bell 238 239 xcom0 at mainbus0 # NS16550 fast serial 240 xcom1 at mainbus0 241 242 ## Audio device; broken 243 #okiadpcm0 at intio0 addr 0xe92000 intr 106 errintr 107 dma 3 244 #audio* at okiadpcm* 245 246 ## Network interfaces 247 neptune0 at intio0 addr 0xece000 intr 249 # Neptune-X 248 neptune1 at intio0 addr 0xece400 intr 249 # Neptune-X at alt. addr. 249 ne0 at neptune? addr 0x300 # NE2000 or clone 250 #se0 at scsibus? target ? lun ? # Ether+; broken 251 252 253 #### Pseudo devices 254 255 ## A disk-like interface to files. Can be used to create floppy, CD, 256 ## miniroot images, etc. 257 258 pseudo-device vnd 4 259 260 ## Concatenated and striped disks; with this, you can create a software-based 261 ## disk array similar to a "RAID 0" setup. See ccd(4). 262 263 #pseudo-device ccd 4 264 265 ## RAIDframe disk driver: software RAID driver. See raid(4). 266 267 #pseudo-device raid 4 268 #options RAID_AUTOCONFIG # auto-configuration of RAID components 269 270 ## Memory disk device, used on boot floppies with compressed 271 ## kernel-plus-root-disk images. 272 273 #pseudo-device md 1 274 275 ## Loopback network interface; required 276 pseudo-device loop 277 278 ## SLIP and CSLIP interfaces, for IP over a serial line. 279 pseudo-device sl 1 280 281 ## PPP, the successor to SLIP. See pppd(8). 282 pseudo-device ppp 1 283 284 ## Network "tunnel" device, allowing protocol stacks to run in the userland. 285 ## This is used by the third-party user-mode "ppp" program, and others. 286 #pseudo-device tun 4 287 288 ## Generic L3 over IP tunnel 289 #pseudo-device gre 2 # generic L3 over IP tunnel 290 291 ## Berkeley Packet Filter, required to run RARPD. A generic C-language 292 ## interface that allows selective examining of incoming packets. 293 pseudo-device bpfilter 4 294 295 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for 296 ## one example of the use of the IP Filter. 297 #pseudo-device ipfilter 298 299 ## for IPv6 300 pseudo-device gif 1 # IPv[46] over IPv[46] tunnel (RFC1933) 301 #pseudo-device faith 1 # IPv[46] tcp relay translation i/f 302 #pseudo-device stf 1 # 6to4 IPv6 over IPv4 encapsulation 303 304 #### Other device configuration 305 306 ## Pseudo ttys, required for network logins and programs like screen. 307 308 pseudo-device pty # pseudo-terminals 309 310 ## Random device, used to implement /dev/random (a source of random noise), 311 ## and generate randomness for some kernel formulae. 312 313 #pseudo-device rnd 314
Indexes created Fri Oct 03 02:09:57 GMT 2025