INSTALL revision 1.16
1# $NetBSD: INSTALL,v 1.16 1999/05/21 15:15:34 minoura Exp $ 2 3# 4# INSTALL -- installation kernel. 5# 6 7include "arch/x68k/conf/std.x68k" 8 9maxusers 8 10 11## Enable the hooks used for initializing the memory-disk. 12options MEMORY_DISK_HOOKS 13options MEMORY_DISK_IS_ROOT # Force root on memory-disk 14options MEMORY_DISK_SERVER=0 # No user space hooks 15#options MINIROOTSIZE=2400 # 1.2M, same as a 130mm floppy 16#options MINIROOTSIZE=2880 # 1.44M, same as a 90mm floppy 17options MINIROOTSIZE=2048 18options BUFCACHE=5 # Reserve 5% of the RAM as the cache. 19 20## System kernel configuration. See options(4) for more detail. 21 22 23## Options for variants of the m68k MPU 24## you must have at least the correct one; REQUIRED 25options M68030 26options M68040 27options M68060 28 29 30#### System options specific to the x68k port 31 32#options EXTENDED_MEMORY # support for >16MB memory 33options FPU_EMULATE # software fpu emulation for MC68030 34options FPSP # floating point emulation for MC68040 35options M060SP # int/fp emulation for MC68060 36options JUPITER # support for "Jupiter-X" accelerator 37#options MAPPEDCOPY # use page mapping for large copyin/copyout 38#options ZSCONSOLE,ZSCN_SPEED="9600" # use serial console 39 40 41#### System options that are the same for all ports 42 43## Root device configuration: change the ?'s if you are going to use a 44## nonstandard root partition (other than where the kernel is booted from) 45## and/or nonstandard root type (not ffs or nfs). Normally this can be 46## automagically determined at boot time. 47 48config netbsd root on ? type ? 49#config netbsd root on sd0 type ffs 50 51## RTC is offset from GMT; -540 means JST-9 52options RTC_OFFSET=-540 # hardware clock is this many mins. west of GMT 53 54## System call tracing (see ktrace(1)). 55#options KTRACE 56 57## Collect statistics on kernel malloc's and free's. This does have a 58## significant performance hit on slower machines, so it is intended for 59## diagnostic use only. 60#options KMEMSTATS 61 62## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 63#options SYSVMSG # System V message queues 64#options SYSVSEM # System V semaphores 65#options SYSVSHM # System V shared memory 66#options SHMMAXPGS=1024 # 1024 pages is the default 67 68## Loadable kernel module support 69#options LKM 70 71## NFS boot options; not supported currently: needs nfsboot program 72#options NFS_BOOT_BOOTPARAM 73#options NFS_BOOT_BOOTP 74#options NFS_BOOT_DHCP 75 76#### Debugging options 77 78## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 79## serial console break or keyboard reset, where the PROM would normally 80## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 81#options DDB # kernel dynamic debugger 82#options DDB_HISTORY_SIZE=100 # enable history editing in DDB 83#options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 84#options PANICBUTTON # interrupt switch invokes DDB 85 86## You may also use gdb, on another computer connected to this machine over 87## a serial port. Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is 88## a dev_t encoded device number of the serial port to use. 89## KGDB is not supported for now. 90#options KGDB # support for kernel gdb 91#options KGDBDEV=0xc00 # kgdb device number 92#options KGDBRATE=9600 # baud rate 93 94## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 95## such that gdb(1) can be used on a kernel coredump. 96 97#makeoptions DEBUG="-g" 98makeoptions COPTS="-Os -fno-inline" 99 100## Adds code to the kernel that does internal consistency checks, and will 101## cause the kernel to panic if corruption of internal data structures 102## is detected. 103#options DIAGNOSTIC # extra kernel sanity checking 104 105## Enable (possibly expensive) debugging code that may also display messages 106## on the system console 107#options DEBUG 108 109## Make SCSI error messages more verbose when explaining their meanings. 110#options SCSIVERBOSE 111 112## `INSECURE' turns off the kernel security level (securelevel = 0 always). 113## This allows writing to /dev/mem, loading kernel modules while multi-user, 114## and other insecurities good only for development work. Do not use this 115## option on a production machine. 116#options INSECURE 117 118## Allow non-root users to grab /dev/console with programs such as xconsole. 119## `xconsole' therefore does not need setuid root with this option enabled. 120#options UCONSOLE 121 122## `FDSCRIPTS' allows non-readable but executable scripts by providing a 123## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 124## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 125## opaque file mechanism. Perl calls this "secure setuid scripts." 126 127#options FDSCRIPTS 128#options SETUIDSCRIPTS 129 130## Options for compatibility with previous releases foreign system binaries. 131 132#options COMPAT_43 # 4.3BSD system interfaces 133#options COMPAT_09 # NetBSD 0.9 binary compatibility 134#options COMPAT_10 # NetBSD 1.0 binary compatibility 135#options COMPAT_11 # NetBSD 1.1 binary compatibility 136#options COMPAT_12 # NetBSD 1.2 binary compatibility 137#options COMPAT_13 # NetBSD 1.3 binary compatibility 138#options COMPAT_M68K4K # NetBSD/m68k4k binaries 139#options COMPAT_SUNOS # SunOS 4.x binary compatibility; broken 140#options COMPAT_SVR4 # SVR4 binary compatibility; broken 141#options COMPAT_LINUX # Linux/m68k binary compatibility 142#options EXEC_ELF32 # 32-bit ELF executables (Linux, SVR4) 143 144## File systems. 145file-system FFS # Berkeley Fast Filesystem 146file-system NFS # Sun NFS-compatible filesystem client 147file-system KERNFS # kernel data-structure filesystem 148#file-system NULLFS # NULL layered filesystem (buggy) 149#file-system MFS # memory-based filesystem 150#file-system FDESC # user file descriptor filesystem 151#file-system UMAPFS # uid/gid remapping filesystem 152#file-system LFS # Log-structured filesystem (experimental) 153#file-system PORTAL # portal filesystem (experimental) 154#file-system PROCFS # /proc 155file-system CD9660 # ISO 9660 + Rock Ridge file system 156#file-system UNION # union file system (a little buggy) 157file-system MSDOSFS # MS-DOS FAT filesystem(s). 158#file-system ADOSFS # AmigaDOS filesystem 159 160## File system options. 161#options NFSSERVER # Sun NFS-compatible filesystem server 162#options QUOTA # FFS quotas 163#options FFS_EI # FFS Endian Independent support 164 165## Network protocol support. In most environments, INET is required. 166options INET # IP (Internet Protocol) v4 167options TCP_COMPAT_42 # 4.2BSD IP implementation compatibility 168#options GATEWAY # packet forwarding ("router switch") 169#options MROUTING # packet forwarding of multicast packets 170#options DIRECTED_BROADCAST # allow broadcasts through routers 171#options NS # Xerox NS networking 172#options NSIP # Xerox NS tunneling over IP 173#options ISO,TPIP # OSI networking 174#options EON # OSI tunneling over IP 175#options CCITT,LLC,HDLC # X.25 packet switched protocol 176#options NETATALK # AppleTalk (over Ethernet) protocol 177#options NTP # Network Time Protocol in-kernel support 178#options PPS_SYNC # Add serial line synchronization for NTP 179#options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 180#options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 181#options PPP_BSDCOMP # Add BSD compression to ppp device 182#options PPP_DEFLATE # Add deflate (libz) compression to ppp device 183#options PPP_FILTER # Add active filters for ppp (via bpf) 184 185 186 187#### Device configurations 188 189## Fundamental devices; see also std.x68k 190dmac0 at intio0 addr 0xe84000 # DMA controler 191xel0 at intio0 192opm0 at intio0 addr 0xe90000 # OPM: required for fdc 193 194## Display devices and console 195grfbus0 at mainbus0 # bitmapped displays 196grf0 at grfbus0 # multiplane graphics 197#grf1 at grfbus0 # flexible graphics 198 199kbd0 at mfp0 # standard keyboard 200ite0 at grf0 # internal terminal emulator 201options ITE_KERNEL_ATTR=4 # bold for kernel messages 202 # see /sys/arch/x68k/dev/itevar.h 203#pseudo-device pow 2 # software power switch 204 205## floppy disks 206fdc0 at intio0 addr 0xe94000 intr 96 dma 0 dmaintr 100 # floppy controler 207fd* at fdc0 unit ? # builtin floppy drives 208 209## SCSI devices 210scsirom0 at intio0 # SCSI BIOS 211scsirom1 at intio0 # SCSI BIOS 212spc* at scsirom? # genuin SCSI 213scsibus* at spc? 214mha0 at scsirom? # Mankai MK-HA1 (Mach-2) 215scsibus* at mha0 216 217sd* at scsibus? target ? lun ? # SCSI disks 218cd* at scsibus? target ? lun ? # SCSI CD-ROMs 219st* at scsibus? target ? lun ? # SCSI tapes 220#ss* at scsibus? target ? lun ? # SCSI scanners 221#ch* at scsibus? target ? lun ? # SCSI changer devices 222#uk* at scsibus? target ? lun ? # SCSI unknown devices 223 224## Serial ports 225zsc0 at intio0 addr 0xe98000 intr 112 226zstty0 at zsc0 channel 0 # built-in RS-232C 227#ms0 at zsc0 channel 1 # standard mouse 228#zsc1 at intio0 addr 0xeafc00 intr 113 229#zstty2 at zsc1 channel 0 230#zstty3 at zsc1 channel 1 231#zsc2 at intio0 addr 0xeafc10 intr 114 232#zstty4 at zsc2 channel 0 233#zstty5 at zsc2 channel 1 234 235#pseudo-device sram # battery-backuped static RAM 236#pseudo-device bell # OPM bell 237 238#xcom0 at mainbus0 # NS16550 fast serial 239#xcom1 at mainbus0 240 241#par0 at mainbus0 # Builtin printer port 242 243## Audio device; broken 244#okiadpcm0 at intio0 addr 0xe92000 intr 106 errintr 107 dma 3 245#audio* at okiadpcm* 246 247## Network interfaces 248neptune0 at intio0 addr 0xece000 intr 249 # Neptune-X 249neptune1 at intio0 addr 0xece400 intr 249 # Neptune-X at alt. addr. 250ne0 at neptune? addr 0x300 # NE2000 or clone 251#se0 at scsibus? target ? lun ? # Ether+; broken 252 253 254#### Pseudo devices 255 256## A disk-like interface to files. Can be used to create floppy, CD, 257## miniroot images, etc. 258 259#pseudo-device vnd 4 260 261## Concatenated and striped disks; with this, you can create a software-based 262## disk array similar to a "RAID 0" setup. See ccd(4). 263 264#pseudo-device ccd 4 265 266## RAIDframe disk driver: software RAID driver. See raid(4). 267 268#pseudo-device raid 4 269 270## Memory disk device, used on boot floppies with compressed 271## kernel-plus-root-disk images. 272 273pseudo-device md 1 274 275## Loopback network interface; required 276pseudo-device loop 277 278## SLIP and CSLIP interfaces, for IP over a serial line. 279pseudo-device sl 1 280 281## PPP, the successor to SLIP. See pppd(8). 282#pseudo-device ppp 1 283 284## Network "tunnel" device, allowing protocol stacks to run in the userland. 285## This is used by the third-party user-mode "ppp" program, and others. 286#pseudo-device tun 4 287 288## Generic L3 over IP tunnel 289#pseudo-device gre 2 # generic L3 over IP tunnel 290 291## Berkeley Packet Filter, required to run RARPD. A generic C-language 292## interface that allows selective examining of incoming packets. 293#pseudo-device bpfilter 8 294 295## IP Filter, used in firewall and NAT applications. See ipnat(8) for 296## one example of the use of the IP Filter. 297#pseudo-device ipfilter 298 299 300#### Other device configuration 301 302## Pseudo ttys, required for network logins and programs like screen. 303## 32 is a good number for average systems; you may have as many as you 304## like, though 256 is more or less the upper limit. Increasing this 305## number still requires you to run /dev/MAKEDEV to create the files 306## for the ptys. 307 308#pseudo-device pty 8 # pseudo-ttys (for network, etc.) 309 310## Random device, used to implement /dev/random (a source of random noise), 311## and generate randomness for some kernel formulae. 312 313#pseudo-device rnd 314