INSTALL revision 1.21
1 # $NetBSD: INSTALL,v 1.21 1999/12/05 15:40:17 minoura Exp $ 2 3 # 4 # INSTALL -- installation kernel. 5 # 6 7 include "arch/x68k/conf/std.x68k" 8 9 maxusers 8 10 11 ## Enable the hooks used for initializing the memory-disk. 12 options MEMORY_DISK_HOOKS 13 options MEMORY_DISK_IS_ROOT # Force root on memory-disk 14 options MEMORY_DISK_SERVER=0 # No user space hooks 15 options MINIROOTSIZE=2400 # 1.2M, same as a 130mm floppy 16 #options MINIROOTSIZE=2880 # 1.44M, same as a 90mm floppy 17 #options MINIROOTSIZE=2048 18 options BUFCACHE=5 # Reserve 5% of the RAM as the cache. 19 20 ## System kernel configuration. See options(4) for more detail. 21 22 23 ## Options for variants of the m68k MPU 24 ## you must have at least the correct one; REQUIRED 25 options M68030 26 options M68040 27 options M68060 28 29 30 #### System options specific to the x68k port 31 32 #options EXTENDED_MEMORY # support for >16MB memory 33 options FPU_EMULATE # software fpu emulation for MC68030 34 options FPSP # floating point emulation for MC68040 35 options M060SP # int/fp emulation for MC68060 36 options JUPITER # support for "Jupiter-X" accelerator 37 #options MAPPEDCOPY # use page mapping for large copyin/copyout 38 #options ZSCONSOLE,ZSCN_SPEED="9600" # use serial console 39 40 41 #### System options that are the same for all ports 42 43 ## Root device configuration: change the ?'s if you are going to use a 44 ## nonstandard root partition (other than where the kernel is booted from) 45 ## and/or nonstandard root type (not ffs or nfs). Normally this can be 46 ## automagically determined at boot time. 47 48 config netbsd root on ? type ? 49 #config netbsd root on sd0 type ffs 50 51 ## RTC is offset from GMT; -540 means JST-9 52 options RTC_OFFSET=-540 # hardware clock is this many mins. west of GMT 53 54 ## System call tracing (see ktrace(1)). 55 #options KTRACE 56 57 ## Collect statistics on kernel malloc's and free's. This does have a 58 ## significant performance hit on slower machines, so it is intended for 59 ## diagnostic use only. 60 #options KMEMSTATS 61 62 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 63 #options SYSVMSG # System V message queues 64 #options SYSVSEM # System V semaphores 65 #options SYSVSHM # System V shared memory 66 #options SHMMAXPGS=1024 # 1024 pages is the default 67 68 ## Loadable kernel module support 69 #options LKM 70 71 ## NFS boot options; not supported currently: needs nfsboot program 72 #options NFS_BOOT_BOOTPARAM 73 #options NFS_BOOT_BOOTP 74 #options NFS_BOOT_DHCP 75 76 #### Debugging options 77 78 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 79 ## serial console break or keyboard reset, where the PROM would normally 80 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 81 #options DDB # kernel dynamic debugger 82 #options DDB_HISTORY_SIZE=100 # enable history editing in DDB 83 #options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 84 #options PANICBUTTON # interrupt switch invokes DDB 85 86 ## You may also use gdb, on another computer connected to this machine over 87 ## a serial port. Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is 88 ## a dev_t encoded device number of the serial port to use. 89 ## KGDB is not supported for now. 90 #options KGDB # support for kernel gdb 91 #options KGDBDEV=0xc00 # kgdb device number 92 #options KGDBRATE=9600 # baud rate 93 94 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 95 ## such that gdb(1) can be used on a kernel coredump. 96 97 #makeoptions DEBUG="-g" 98 makeoptions COPTS="-Os" 99 100 ## Adds code to the kernel that does internal consistency checks, and will 101 ## cause the kernel to panic if corruption of internal data structures 102 ## is detected. 103 #options DIAGNOSTIC # extra kernel sanity checking 104 105 ## Enable (possibly expensive) debugging code that may also display messages 106 ## on the system console 107 #options DEBUG 108 109 ## Make SCSI error messages more verbose when explaining their meanings. 110 #options SCSIVERBOSE 111 112 ## `INSECURE' turns off the kernel security level (securelevel = 0 always). 113 ## This allows writing to /dev/mem, loading kernel modules while multi-user, 114 ## and other insecurities good only for development work. Do not use this 115 ## option on a production machine. 116 #options INSECURE 117 118 ## Allow non-root users to grab /dev/console with programs such as xconsole. 119 ## `xconsole' therefore does not need setuid root with this option enabled. 120 #options UCONSOLE 121 122 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a 123 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 124 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 125 ## opaque file mechanism. Perl calls this "secure setuid scripts." 126 127 #options FDSCRIPTS 128 #options SETUIDSCRIPTS 129 130 ## Options for compatibility with previous releases foreign system binaries. 131 132 #options COMPAT_43 # 4.3BSD system interfaces 133 #options COMPAT_09 # NetBSD 0.9 binary compatibility 134 #options COMPAT_10 # NetBSD 1.0 binary compatibility 135 #options COMPAT_11 # NetBSD 1.1 binary compatibility 136 #options COMPAT_12 # NetBSD 1.2 binary compatibility 137 #options COMPAT_13 # NetBSD 1.3 binary compatibility 138 #options COMPAT_14 # NetBSD 1.4 binary compatibility 139 #options COMPAT_M68K4K # NetBSD/m68k4k binaries 140 #options COMPAT_SUNOS # SunOS 4.x binary compatibility; broken 141 #options COMPAT_SVR4 # SVR4 binary compatibility; broken 142 #options COMPAT_LINUX # Linux/m68k binary compatibility 143 #options EXEC_ELF32 # 32-bit ELF executables (Linux, SVR4) 144 145 ## File systems. 146 file-system FFS # Berkeley Fast Filesystem 147 file-system NFS # Sun NFS-compatible filesystem client 148 file-system KERNFS # kernel data-structure filesystem 149 #file-system NULLFS # NULL layered filesystem (buggy) 150 #file-system MFS # memory-based filesystem 151 #file-system FDESC # user file descriptor filesystem 152 #file-system UMAPFS # uid/gid remapping filesystem 153 #file-system LFS # Log-structured filesystem (experimental) 154 #file-system PORTAL # portal filesystem (experimental) 155 #file-system PROCFS # /proc 156 file-system CD9660 # ISO 9660 + Rock Ridge file system 157 #file-system UNION # union file system (a little buggy) 158 file-system MSDOSFS # MS-DOS FAT filesystem(s). 159 #file-system ADOSFS # AmigaDOS filesystem 160 161 ## File system options. 162 #options NFSSERVER # Sun NFS-compatible filesystem server 163 #options QUOTA # FFS quotas 164 #options FFS_EI # FFS Endian Independent support 165 #options SOFTDEP # FFS soft updates support. 166 167 ## Network protocol support. In most environments, INET is required. 168 options INET # IP (Internet Protocol) v4 169 options TCP_COMPAT_42 # 4.2BSD IP implementation compatibility 170 #options GATEWAY # packet forwarding ("router switch") 171 #options MROUTING # packet forwarding of multicast packets 172 #options DIRECTED_BROADCAST # allow broadcasts through routers 173 #options NS # Xerox NS networking 174 #options NSIP # Xerox NS tunneling over IP 175 #options ISO,TPIP # OSI networking 176 #options EON # OSI tunneling over IP 177 #options CCITT,LLC,HDLC # X.25 packet switched protocol 178 #options NETATALK # AppleTalk (over Ethernet) protocol 179 #options NTP # Network Time Protocol in-kernel support 180 #options PPS_SYNC # Add serial line synchronization for NTP 181 #options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 182 #options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 183 #options PPP_BSDCOMP # Add BSD compression to ppp device 184 #options PPP_DEFLATE # Add deflate (libz) compression to ppp device 185 #options PPP_FILTER # Add active filters for ppp (via bpf) 186 187 188 189 #### Device configurations 190 191 ## Fundamental devices; see also std.x68k 192 dmac0 at intio0 addr 0xe84000 # DMA controler 193 xel0 at intio0 194 opm0 at intio0 addr 0xe90000 # OPM: required for fdc 195 196 ## Display devices and console 197 grfbus0 at mainbus0 # bitmapped displays 198 grf0 at grfbus0 # multiplane graphics 199 #grf1 at grfbus0 # flexible graphics 200 201 kbd0 at mfp0 # standard keyboard 202 ite0 at grf0 # internal terminal emulator 203 options ITE_KERNEL_ATTR=4 # bold for kernel messages 204 # see /sys/arch/x68k/dev/itevar.h 205 #pseudo-device pow 2 # software power switch 206 207 ## floppy disks 208 fdc0 at intio0 addr 0xe94000 intr 96 dma 0 dmaintr 100 # floppy controler 209 fd* at fdc0 unit ? # builtin floppy drives 210 211 ## SCSI devices 212 scsirom0 at intio0 # SCSI BIOS 213 scsirom1 at intio0 # SCSI BIOS 214 spc* at scsirom? # genuin SCSI 215 scsibus* at spc? 216 mha0 at scsirom? # Mankai MK-HA1 (Mach-2) 217 scsibus* at mha0 218 219 sd* at scsibus? target ? lun ? # SCSI disks 220 cd* at scsibus? target ? lun ? # SCSI CD-ROMs 221 st* at scsibus? target ? lun ? # SCSI tapes 222 #ss* at scsibus? target ? lun ? # SCSI scanners 223 #ch* at scsibus? target ? lun ? # SCSI changer devices 224 #uk* at scsibus? target ? lun ? # SCSI unknown devices 225 226 ## Serial ports 227 zsc0 at intio0 addr 0xe98000 intr 112 228 zstty0 at zsc0 channel 0 # built-in RS-232C 229 #ms0 at zsc0 channel 1 # standard mouse 230 #zsc1 at intio0 addr 0xeafc00 intr 113 231 #zstty2 at zsc1 channel 0 232 #zstty3 at zsc1 channel 1 233 #zsc2 at intio0 addr 0xeafc10 intr 114 234 #zstty4 at zsc2 channel 0 235 #zstty5 at zsc2 channel 1 236 237 #pseudo-device sram # battery-backuped static RAM 238 #pseudo-device bell # OPM bell 239 240 #xcom0 at mainbus0 # NS16550 fast serial 241 #xcom1 at mainbus0 242 243 #par0 at mainbus0 # Builtin printer port 244 245 ## Audio device; broken 246 #okiadpcm0 at intio0 addr 0xe92000 intr 106 errintr 107 dma 3 247 #audio* at okiadpcm* 248 249 ## Network interfaces 250 neptune0 at intio0 addr 0xece000 intr 249 # Neptune-X 251 neptune1 at intio0 addr 0xece400 intr 249 # Neptune-X at alt. addr. 252 ne0 at neptune? addr 0x300 # NE2000 or clone 253 #se0 at scsibus? target ? lun ? # Ether+; broken 254 255 256 #### Pseudo devices 257 258 ## A disk-like interface to files. Can be used to create floppy, CD, 259 ## miniroot images, etc. 260 261 #pseudo-device vnd 4 262 263 ## Concatenated and striped disks; with this, you can create a software-based 264 ## disk array similar to a "RAID 0" setup. See ccd(4). 265 266 #pseudo-device ccd 4 267 268 ## RAIDframe disk driver: software RAID driver. See raid(4). 269 270 #pseudo-device raid 4 271 272 ## Memory disk device, used on boot floppies with compressed 273 ## kernel-plus-root-disk images. 274 275 pseudo-device md 1 276 277 ## Loopback network interface; required 278 pseudo-device loop 279 280 ## SLIP and CSLIP interfaces, for IP over a serial line. 281 pseudo-device sl 1 282 283 ## PPP, the successor to SLIP. See pppd(8). 284 #pseudo-device ppp 1 285 286 ## Network "tunnel" device, allowing protocol stacks to run in the userland. 287 ## This is used by the third-party user-mode "ppp" program, and others. 288 #pseudo-device tun 4 289 290 ## Generic L3 over IP tunnel 291 #pseudo-device gre 2 # generic L3 over IP tunnel 292 293 ## Berkeley Packet Filter, required to run RARPD. A generic C-language 294 ## interface that allows selective examining of incoming packets. 295 #pseudo-device bpfilter 8 296 297 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for 298 ## one example of the use of the IP Filter. 299 #pseudo-device ipfilter 300 301 302 #### Other device configuration 303 304 ## Pseudo ttys, required for network logins and programs like screen. 305 ## 32 is a good number for average systems; you may have as many as you 306 ## like, though 256 is more or less the upper limit. Increasing this 307 ## number still requires you to run /dev/MAKEDEV to create the files 308 ## for the ptys. 309 310 pseudo-device pty 2 # pseudo-ttys (for network, etc.) 311 312 ## Random device, used to implement /dev/random (a source of random noise), 313 ## and generate randomness for some kernel formulae. 314 315 #pseudo-device rnd 316
Indexes created Wed Oct 29 20:09:47 GMT 2025