INSTALL revision 1.55
1 # $NetBSD: INSTALL,v 1.55 2003/09/06 03:25:32 itojun Exp $ 2 3 # 4 # INSTALL -- installation kernel. 5 # 6 7 include "arch/x68k/conf/std.x68k" 8 9 #options INCLUDE_CONFIG_FILE # embed config file in kernel binary 10 11 #ident "INSTALL-$Revision: 1.55 $" 12 13 makeoptions COPTS="-Os" # Optimise for space. Implies -O2 14 15 maxusers 4 16 17 ## Enable the hooks used for initializing the memory-disk. 18 options MEMORY_DISK_HOOKS 19 options MEMORY_DISK_IS_ROOT # Force root on memory-disk 20 options MEMORY_DISK_SERVER=0 # No user space hooks 21 #options MEMORY_DISK_ROOT_SIZE=2400 # 1.2M, same as a 130mm floppy 22 #options MEMORY_DISK_ROOT_SIZE=2880 # 1.44M, same as a 90mm floppy 23 options MEMORY_DISK_ROOT_SIZE=2550 24 25 ## System kernel configuration. See options(4) for more detail. 26 27 28 ## Options for variants of the m68k MPU 29 ## you must have at least the correct one; REQUIRED 30 options M68030 31 options M68040 32 options M68060 33 ## If you want an optimized kernel for a specific processor, use either: 34 #makeoptions CMACHFLAGS="-m68030" 35 #makeoptions CMACHFLAGS="-m68040 -Wa,-m68030 -Wa,-m68851" 36 #makeoptions CMACHFLAGS="-m68060 -Wa,-m68030 -Wa,-m68851" 37 38 39 #### System options specific to the x68k port 40 41 options EXTENDED_MEMORY # support for >16MB memory 42 options FPU_EMULATE # software fpu emulation for MC68030 43 options FPSP # floating point emulation for MC68040 44 options M060SP # int/fp emulation for MC68060 45 #options JUPITER # support for "Jupiter-X" accelerator 46 #options MAPPEDCOPY # use page mapping for large copyin/copyout 47 #options ZSCONSOLE,ZSCN_SPEED="9600" # use serial console 48 49 50 #### System options that are the same for all ports 51 52 ## Root device configuration: change the ?'s if you are going to use a 53 ## nonstandard root partition (other than where the kernel is booted from) 54 ## and/or nonstandard root type (not ffs or nfs). Normally this can be 55 ## automagically determined at boot time. 56 57 config netbsd root on ? type ? 58 #config netbsd root on sd0 type ffs 59 60 ## RTC is offset from GMT; -540 means JST-9 61 options RTC_OFFSET=-540 # hardware clock is this many mins. west of GMT 62 63 ## System call tracing (see ktrace(1)). 64 #options KTRACE 65 66 ## Collect statistics on kernel malloc's and free's. This does have a 67 ## significant performance hit on slower machines, so it is intended for 68 ## diagnostic use only. 69 #options KMEMSTATS 70 71 ## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 72 #options SYSVMSG # System V message queues 73 #options SYSVSEM # System V semaphores 74 #options SYSVSHM # System V shared memory 75 #options SHMMAXPGS=1024 # 1024 pages is the default 76 77 ## Loadable kernel module support 78 #options LKM 79 80 options USERCONF # userconf(4) support 81 options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 82 options MALLOC_NOINLINE # Not inlining MALLOC saves memory 83 84 ## NFS boot options; not supported currently: needs nfsboot program 85 #options NFS_BOOT_BOOTPARAM 86 #options NFS_BOOT_BOOTP 87 #options NFS_BOOT_DHCP 88 89 #### Debugging options 90 91 ## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 92 ## serial console break or keyboard reset, where the PROM would normally 93 ## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 94 #options DDB # kernel dynamic debugger 95 #options DDB_HISTORY_SIZE=100 # enable history editing in DDB 96 #options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 97 #options PANICBUTTON # interrupt switch invokes DDB 98 99 ## You may also use gdb, on another computer connected to this machine over 100 ## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 101 ## KGDB_DEV is a dev_t encoded device number of the serial port to use. 102 ## KGDB is not supported for now. 103 #options KGDB # support for kernel gdb 104 #options KGDB_DEV=0xc00 # kgdb device number 105 #options KGDB_DEVRATE=9600 # baud rate 106 107 ## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 108 ## such that gdb(1) can be used on a kernel coredump. 109 110 #makeoptions DEBUG="-g" 111 112 ## Adds code to the kernel that does internal consistency checks, and will 113 ## cause the kernel to panic if corruption of internal data structures 114 ## is detected. 115 #options DIAGNOSTIC # extra kernel sanity checking 116 117 ## Enable (possibly expensive) debugging code that may also display messages 118 ## on the system console 119 #options DEBUG 120 121 ## Make SCSI error messages more verbose when explaining their meanings. 122 #options SCSIVERBOSE 123 124 ## `INSECURE' turns off the kernel security level (securelevel = 0 always). 125 ## This allows writing to /dev/mem, loading kernel modules while multi-user, 126 ## and other insecurities good only for development work. Do not use this 127 ## option on a production machine. 128 #options INSECURE 129 130 ## `FDSCRIPTS' allows non-readable but executable scripts by providing a 131 ## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 132 ## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 133 ## opaque file mechanism. Perl calls this "secure setuid scripts." 134 135 #options FDSCRIPTS 136 #options SETUIDSCRIPTS 137 138 ## Options for compatibility with previous releases foreign system binaries. 139 140 #options COMPAT_43 # 4.3BSD system interfaces 141 #options COMPAT_09 # NetBSD 0.9 binary compatibility 142 #options COMPAT_10 # NetBSD 1.0 binary compatibility 143 #options COMPAT_11 # NetBSD 1.1 binary compatibility 144 #options COMPAT_12 # NetBSD 1.2 binary compatibility 145 #options COMPAT_13 # NetBSD 1.3 binary compatibility 146 #options COMPAT_14 # NetBSD 1.4 binary compatibility 147 #options COMPAT_AOUT_M68K # compatibility with NetBSD/m68k a.out 148 #options COMPAT_M68K4K # NetBSD/m68k4k binaries 149 #options COMPAT_SUNOS # SunOS 4.x binary compatibility; broken 150 #options COMPAT_SVR4 # SVR4 binary compatibility; broken 151 #options COMPAT_LINUX # Linux/m68k binary compatibility 152 #options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended. 153 154 ## File systems. 155 file-system FFS # Berkeley Fast Filesystem 156 file-system NFS # Sun NFS-compatible filesystem client 157 #file-system KERNFS # kernel data-structure filesystem 158 #file-system NULLFS # NULL layered filesystem (buggy) 159 #file-system OVERLAY # overlay file system 160 #file-system MFS # memory-based filesystem 161 #file-system FDESC # user file descriptor filesystem 162 #file-system UMAPFS # uid/gid remapping filesystem 163 #file-system LFS # Log-structured filesystem (experimental) 164 #file-system PORTAL # portal filesystem (experimental) 165 #file-system PROCFS # /proc 166 file-system CD9660 # ISO 9660 + Rock Ridge file system 167 #file-system UNION # union file system (a little buggy) 168 file-system MSDOSFS # MS-DOS FAT filesystem(s). 169 #file-system ADOSFS # AmigaDOS filesystem 170 171 ## File system options. 172 #options NFSSERVER # Sun NFS-compatible filesystem server 173 #options QUOTA # FFS quotas 174 #options FFS_EI # FFS Endian Independent support 175 #options SOFTDEP # FFS soft updates support. 176 #options NFS_V2_ONLY # Exclude NFS3 and NQNFS code to save space 177 options VNODE_OP_NOINLINE # Not inlining vnode op calls saves mem 178 179 ## Network protocol support. In most environments, INET is required. 180 options INET # IP (Internet Protocol) v4 181 options INET6 # IPV6 182 #options IPSEC # IP security 183 #options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 184 #options IPSEC_DEBUG # debug for IP security 185 #options GATEWAY # packet forwarding ("router switch") 186 #options MROUTING # packet forwarding of multicast packets 187 #options DIRECTED_BROADCAST # allow broadcasts through routers 188 #options NS # Xerox NS networking 189 #options NSIP # Xerox NS tunneling over IP 190 #options ISO,TPIP # OSI networking 191 #options EON # OSI tunneling over IP 192 #options CCITT,LLC,HDLC # X.25 packet switched protocol 193 #options NETATALK # AppleTalk (over Ethernet) protocol 194 #options NTP # Network Time Protocol in-kernel support 195 #options PPS_SYNC # Add serial line synchronization for NTP 196 #options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 197 #options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 198 #options PPP_BSDCOMP # Add BSD compression to ppp device 199 #options PPP_DEFLATE # Add deflate (libz) compression to ppp device 200 #options PPP_FILTER # Add active filters for ppp (via bpf) 201 #options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG 202 203 204 #### Device configurations 205 206 ## Fundamental devices; see also std.x68k 207 dmac0 at intio0 addr 0xe84000 # DMA controler 208 xel0 at intio0 209 opm0 at intio0 addr 0xe90000 # OPM: required for fdc 210 211 ## Display devices and console 212 grfbus0 at mainbus0 # bitmapped displays 213 grf0 at grfbus0 # multiplane graphics 214 #grf1 at grfbus0 # flexible graphics 215 216 kbd0 at mfp0 # standard keyboard 217 ite0 at grf0 # internal terminal emulator 218 options ITE_KERNEL_ATTR=4 # bold for kernel messages 219 # see /sys/arch/x68k/dev/itevar.h 220 #pseudo-device pow 2 # software power switch 221 222 ## floppy disks 223 fdc0 at intio0 addr 0xe94000 intr 96 dma 0 dmaintr 100 # floppy controler 224 fd* at fdc0 unit ? # builtin floppy drives 225 226 ## SCSI devices 227 scsirom0 at intio0 # SCSI BIOS 228 scsirom1 at intio0 # SCSI BIOS 229 spc* at scsirom? # genuin SCSI 230 scsibus* at spc? 231 mha0 at scsirom? # Mankai MK-HA1 (Mach-2) 232 scsibus* at mha0 233 234 sd* at scsibus? target ? lun ? # SCSI disks 235 cd* at scsibus? target ? lun ? # SCSI CD-ROMs 236 st* at scsibus? target ? lun ? # SCSI tapes 237 #ss* at scsibus? target ? lun ? # SCSI scanners 238 #ch* at scsibus? target ? lun ? # SCSI changer devices 239 #uk* at scsibus? target ? lun ? # SCSI unknown devices 240 241 ## Ports 242 zsc0 at intio0 addr 0xe98000 intr 112 243 zstty0 at zsc0 channel 0 # built-in RS-232C 244 #ms0 at zsc0 channel 1 # standard mouse 245 #zsc1 at intio0 addr 0xeafc00 intr 113 246 #zstty2 at zsc1 channel 0 247 #zstty3 at zsc1 channel 1 248 #zsc2 at intio0 addr 0xeafc10 intr 114 249 #zstty4 at zsc2 channel 0 250 #zstty5 at zsc2 channel 1 251 #par0 at intio0 addr 0xe8c000 # Builtin printer port 252 253 pseudo-device sram # battery-backuped static RAM 254 #pseudo-device bell # OPM bell 255 256 #xcom0 at mainbus0 # NS16550 fast serial 257 #xcom1 at mainbus0 258 259 ## Audio device 260 #vs0 at intio0 addr 0xe92000 dma 3 dmaintr 106 261 #audio* at vs? 262 263 ## Network interfaces 264 ne* at intio0 addr 0xece300 intr 249 # Nereid Ethernet 265 ne* at intio0 addr 0xeceb00 intr 248 # Nereid Ethernet 266 neptune0 at intio0 addr 0xece000 intr 249 # Neptune-X 267 neptune1 at intio0 addr 0xece400 intr 249 # Neptune-X at alt. addr. 268 ne* at neptune? addr 0x300 # NE2000 or clone 269 270 271 #### Pseudo devices 272 273 ## A disk-like interface to files. Can be used to create floppy, CD, 274 ## miniroot images, etc. 275 276 #pseudo-device vnd 4 277 278 ## Concatenated and striped disks; with this, you can create a software-based 279 ## disk array similar to a "RAID 0" setup. See ccd(4). 280 281 #pseudo-device ccd 4 282 283 ## RAIDframe disk driver: software RAID driver. See raid(4). 284 285 #pseudo-device raid 4 286 #options RAID_AUTOCONFIG # auto-configuration of RAID components 287 288 ## Memory disk device, used on boot floppies with compressed 289 ## kernel-plus-root-disk images. 290 291 pseudo-device md 1 292 293 ## Loopback network interface; required 294 pseudo-device loop 295 296 ## SLIP and CSLIP interfaces, for IP over a serial line. 297 pseudo-device sl 1 298 299 ## PPP, the successor to SLIP. See pppd(8). 300 #pseudo-device ppp 1 301 302 ## Network "tunnel" device, allowing protocol stacks to run in the userland. 303 ## This is used by the third-party user-mode "ppp" program, and others. 304 #pseudo-device tun 4 305 306 ## Generic L3 over IP tunnel 307 #pseudo-device gre 2 # generic L3 over IP tunnel 308 309 ## Berkeley Packet Filter, required to run RARPD. A generic C-language 310 ## interface that allows selective examining of incoming packets. 311 #pseudo-device bpfilter 4 312 313 ## IP Filter, used in firewall and NAT applications. See ipnat(8) for 314 ## one example of the use of the IP Filter. 315 #pseudo-device ipfilter 316 317 ## for IPv6 318 #pseudo-device gif 1 # IPv[46] over IPv[46] tunnel (RFC1933) 319 #pseudo-device faith 1 # IPv[46] tcp relay translation i/f 320 #pseudo-device stf 1 # 6to4 IPv6 over IPv4 encapsulation 321 322 ## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 323 #pseudo-device vlan 324 325 ## Simple inter-network traffic bridging 326 #pseudo-device bridge 327 328 #### Other device configuration 329 330 ## Pseudo ttys, required for network logins and programs like screen. 331 332 pseudo-device pty 2 # pseudo-terminals (Sysinst needs two) 333 334 ## Random device, used to implement /dev/random (a source of random noise), 335 ## and generate randomness for some kernel formulae. 336 337 pseudo-device rnd 338
Indexes created Tue Oct 14 11:09:46 GMT 2025