ZSCONS revision 1.12
1# $NetBSD: ZSCONS,v 1.12 2000/04/16 14:17:59 minoura Exp $ 2 3# 4# ZSCONS -- like GENERIC, but use zs console. 5# 6 7include "arch/x68k/conf/std.x68k" 8 9#ident "ZSCONS-$Revision: 1.12 $" 10 11maxusers 32 12 13## System kernel configuration. See options(4) for more detail. 14 15 16## Options for variants of the m68k MPU 17## you must have at least the correct one; REQUIRED 18options M68030 19options M68040 20options M68060 21 22 23#### System options specific to the x68k port 24 25options EXTENDED_MEMORY # support for >16MB memory 26options FPU_EMULATE # software fpu emulation for MC68030 27options FPSP # floating point emulation for MC68040 28options M060SP # int/fp emulation for MC68060 29options JUPITER # support for "Jupiter-X" accelerator 30#options MAPPEDCOPY # use page mapping for large copyin/copyout 31options ZSCONSOLE,ZSCN_SPEED="9600" # use serial console 32 33 34#### System options that are the same for all ports 35 36## Root device configuration: change the ?'s if you are going to use a 37## nonstandard root partition (other than where the kernel is booted from) 38## and/or nonstandard root type (not ffs or nfs). Normally this can be 39## automagically determined at boot time. 40 41config netbsd root on ? type ? 42#config netbsd root on sd0 type ffs 43 44## RTC is offset from GMT; -540 means JST-9 45options RTC_OFFSET=-540 # hardware clock is this many mins. west of GMT 46 47## System call tracing (see ktrace(1)). 48options KTRACE 49 50## Collect statistics on kernel malloc's and free's. This does have a 51## significant performance hit on slower machines, so it is intended for 52## diagnostic use only. 53#options KMEMSTATS 54 55## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 56options SYSVMSG # System V message queues 57options SYSVSEM # System V semaphores 58options SYSVSHM # System V shared memory 59#options SHMMAXPGS=1024 # 1024 pages is the default 60 61## Loadable kernel module support 62#options LKM 63 64## NFS boot options; not supported currently: needs nfsboot program 65#options NFS_BOOT_BOOTPARAM 66#options NFS_BOOT_BOOTP 67#options NFS_BOOT_DHCP 68 69#### Debugging options 70 71## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 72## serial console break or keyboard reset, where the PROM would normally 73## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 74#options DDB # kernel dynamic debugger 75#options DDB_HISTORY_SIZE=100 # enable history editing in DDB 76#options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 77#options PANICBUTTON # interrupt switch invokes DDB 78 79## You may also use gdb, on another computer connected to this machine over 80## a serial port. Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is 81## a dev_t encoded device number of the serial port to use. 82## KGDB is not supported for now. 83#options KGDB # support for kernel gdb 84#options KGDBDEV=0xc00 # kgdb device number 85#options KGDBRATE=9600 # baud rate 86 87## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 88## such that gdb(1) can be used on a kernel coredump. 89 90#makeoptions DEBUG="-g" 91 92## Adds code to the kernel that does internal consistency checks, and will 93## cause the kernel to panic if corruption of internal data structures 94## is detected. 95#options DIAGNOSTIC # extra kernel sanity checking 96 97## Enable (possibly expensive) debugging code that may also display messages 98## on the system console 99#options DEBUG 100 101## Make SCSI error messages more verbose when explaining their meanings. 102options SCSIVERBOSE 103 104## `INSECURE' turns off the kernel security level (securelevel = 0 always). 105## This allows writing to /dev/mem, loading kernel modules while multi-user, 106## and other insecurities good only for development work. Do not use this 107## option on a production machine. 108#options INSECURE 109 110## Allow non-root users to grab /dev/console with programs such as xconsole. 111## `xconsole' therefore does not need setuid root with this option enabled. 112#options UCONSOLE 113 114## `FDSCRIPTS' allows non-readable but executable scripts by providing a 115## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 116## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 117## opaque file mechanism. Perl calls this "secure setuid scripts." 118 119#options FDSCRIPTS 120#options SETUIDSCRIPTS 121 122## Options for compatibility with previous releases foreign system binaries. 123 124options COMPAT_43 # 4.3BSD system interfaces 125options COMPAT_09 # NetBSD 0.9 binary compatibility 126options COMPAT_10 # NetBSD 1.0 binary compatibility 127options COMPAT_11 # NetBSD 1.1 binary compatibility 128options COMPAT_12 # NetBSD 1.2 binary compatibility 129options COMPAT_13 # NetBSD 1.3 binary compatibility 130options COMPAT_14 # NetBSD 1.4 binary compatibility 131#options COMPAT_M68K4K # NetBSD/m68k4k binaries 132#options COMPAT_SUNOS # SunOS 4.x binary compatibility; broken 133#options COMPAT_SVR4 # SVR4 binary compatibility; broken 134#options COMPAT_LINUX # Linux/m68k binary compatibility 135#options EXEC_ELF32 # 32-bit ELF executables (Linux, SVR4) 136 137## File systems. 138file-system FFS # Berkeley Fast Filesystem 139file-system NFS # Sun NFS-compatible filesystem client 140file-system KERNFS # kernel data-structure filesystem 141#file-system NULLFS # NULL layered filesystem (buggy) 142#file-system OVERLAY # overlay file system 143file-system MFS # memory-based filesystem 144#file-system FDESC # user file descriptor filesystem 145file-system UMAPFS # uid/gid remapping filesystem 146#file-system LFS # Log-structured filesystem (experimental) 147#file-system PORTAL # portal filesystem (experimental) 148file-system PROCFS # /proc 149file-system CD9660 # ISO 9660 + Rock Ridge file system 150#file-system UNION # union file system (a little buggy) 151file-system MSDOSFS # MS-DOS FAT filesystem(s). 152#file-system ADOSFS # AmigaDOS filesystem 153 154## File system options. 155options NFSSERVER # Sun NFS-compatible filesystem server 156options QUOTA # FFS quotas 157#options FFS_EI # FFS Endian Independent support 158#options SOFTDEP # FFS soft updates support. 159 160# Pull in config fragments for kernel crypto. This is required for 161# options IPSEC etc. to work. If you want to run with IPSEC, uncomment 162# one of these, based on whether you use crypto-us or crypto-intl, and 163# adjust the prefixes as necessary. 164 165#prefix ../crypto-us/sys 166#cinclude "conf/files.crypto-us" 167#prefix 168 169#prefix ../crypto-intl/sys 170#cinclude "conf/files.crypto-intl" 171#prefix 172 173## Network protocol support. In most environments, INET is required. 174options INET # IP (Internet Protocol) v4 175options INET6 # IPV6 176#options IPSEC # IP security 177#options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 178#options IPSEC_DEBUG # debug for IP security 179options TCP_COMPAT_42 # 4.2BSD IP implementation compatibility 180#options GATEWAY # packet forwarding ("router switch") 181#options MROUTING # packet forwarding of multicast packets 182#options DIRECTED_BROADCAST # allow broadcasts through routers 183#options NS # Xerox NS networking 184#options NSIP # Xerox NS tunneling over IP 185#options ISO,TPIP # OSI networking 186#options EON # OSI tunneling over IP 187#options CCITT,LLC,HDLC # X.25 packet switched protocol 188options NETATALK # AppleTalk (over Ethernet) protocol 189options NTP # Network Time Protocol in-kernel support 190#options PPS_SYNC # Add serial line synchronization for NTP 191options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 192options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 193options PPP_BSDCOMP # Add BSD compression to ppp device 194options PPP_DEFLATE # Add deflate (libz) compression to ppp device 195options PPP_FILTER # Add active filters for ppp (via bpf) 196 197 198 199#### Device configurations 200 201## Fundamental devices; see also std.x68k 202dmac0 at intio0 addr 0xe84000 # DMA controler 203xel0 at intio0 204opm0 at intio0 addr 0xe90000 # OPM: required for fdc 205 206## Display devices and console 207grfbus0 at mainbus0 # bitmapped displays 208grf0 at grfbus0 # multiplane graphics 209grf1 at grfbus0 # flexible graphics 210 211#kbd0 at mfp0 # standard keyboard 212#ite0 at grf0 # internal terminal emulator 213#options ITE_KERNEL_ATTR=4 # bold for kernel messages 214 # see /sys/arch/x68k/dev/itevar.h 215pseudo-device pow 2 # software power switch 216 217## floppy disks 218fdc0 at intio0 addr 0xe94000 intr 96 dma 0 dmaintr 100 # floppy controler 219fd* at fdc0 unit ? # builtin floppy drives 220 221## SCSI devices 222scsirom0 at intio0 addr 0xfc0000 # Built-in SCSI BIOS 223scsirom1 at intio0 addr 0xea0020 # External SCSI BIOS 224spc0 at scsirom0 # genuin SCSI 225spc1 at scsirom1 # genuin SCSI 226scsibus* at spc? 227mha0 at scsirom1 # Mankai MK-HA1 (Mach-2) 228scsibus* at mha0 229 230sd* at scsibus? target ? lun ? # SCSI disks 231cd* at scsibus? target ? lun ? # SCSI CD-ROMs 232st* at scsibus? target ? lun ? # SCSI tapes 233#ss* at scsibus? target ? lun ? # SCSI scanners 234ch* at scsibus? target ? lun ? # SCSI changer devices 235#uk* at scsibus? target ? lun ? # SCSI unknown devices 236 237## Ports 238zsc0 at intio0 addr 0xe98000 intr 112 239zstty0 at zsc0 channel 0 # built-in RS-232C 240ms0 at zsc0 channel 1 # standard mouse 241#zsc1 at intio0 addr 0xeafc00 intr 113 242#zstty2 at zsc1 channel 0 243#zstty3 at zsc1 channel 1 244#zsc2 at intio0 addr 0xeafc10 intr 114 245#zstty4 at zsc2 channel 0 246#zstty5 at zsc2 channel 1 247par0 at intio0 addr 0xe8c000 # Builtin printer port 248 249pseudo-device sram # battery-backuped static RAM 250pseudo-device bell # OPM bell 251 252xcom0 at mainbus0 # NS16550 fast serial 253xcom1 at mainbus0 254 255## Audio device; broken 256#okiadpcm0 at intio0 addr 0xe92000 intr 106 errintr 107 dma 3 257#audio* at okiadpcm* 258 259## Network interfaces 260neptune0 at intio0 addr 0xece000 intr 249 # Neptune-X 261neptune1 at intio0 addr 0xece400 intr 249 # Neptune-X at alt. addr. 262ne0 at neptune? addr 0x300 # NE2000 or clone 263#se0 at scsibus? target ? lun ? # Ether+; broken 264 265 266#### Pseudo devices 267 268## A disk-like interface to files. Can be used to create floppy, CD, 269## miniroot images, etc. 270 271pseudo-device vnd 4 272 273## Concatenated and striped disks; with this, you can create a software-based 274## disk array similar to a "RAID 0" setup. See ccd(4). 275 276pseudo-device ccd 4 277 278## RAIDframe disk driver: software RAID driver. See raid(4). 279 280pseudo-device raid 4 281#options RAID_AUTOCONFIG # auto-configuration of RAID components 282 283## Memory disk device, used on boot floppies with compressed 284## kernel-plus-root-disk images. 285 286#pseudo-device md 1 287 288## Loopback network interface; required 289pseudo-device loop 290 291## SLIP and CSLIP interfaces, for IP over a serial line. 292pseudo-device sl 1 293 294## PPP, the successor to SLIP. See pppd(8). 295pseudo-device ppp 1 296 297## Network "tunnel" device, allowing protocol stacks to run in the userland. 298## This is used by the third-party user-mode "ppp" program, and others. 299pseudo-device tun 4 300 301## Generic L3 over IP tunnel 302#pseudo-device gre 2 # generic L3 over IP tunnel 303 304## Berkeley Packet Filter, required to run RARPD. A generic C-language 305## interface that allows selective examining of incoming packets. 306pseudo-device bpfilter 8 307 308## IP Filter, used in firewall and NAT applications. See ipnat(8) for 309## one example of the use of the IP Filter. 310pseudo-device ipfilter 311 312## for IPv6 313pseudo-device gif 4 # IPv[46] over IPv[46] tunnel (RFC1933) 314#pseudo-device faith 1 # IPv[46] tcp relay translation i/f 315 316#### Other device configuration 317 318## Pseudo ttys, required for network logins and programs like screen. 319## 32 is a good number for average systems; you may have as many as you 320## like, though 256 is more or less the upper limit. Increasing this 321## number still requires you to run /dev/MAKEDEV to create the files 322## for the ptys. 323 324pseudo-device pty 32 # pseudo-ttys (for network, etc.) 325 326## Random device, used to implement /dev/random (a source of random noise), 327## and generate randomness for some kernel formulae. 328 329pseudo-device rnd 330