ZSCONS revision 1.8
1# $NetBSD: ZSCONS,v 1.8 1999/07/29 10:37:26 augustss Exp $ 2 3# 4# ZSCONS -- like GENERIC, but use zs console. 5# 6 7include "arch/x68k/conf/std.x68k" 8 9maxusers 32 10 11## System kernel configuration. See options(4) for more detail. 12 13 14## Options for variants of the m68k MPU 15## you must have at least the correct one; REQUIRED 16options M68030 17options M68040 18options M68060 19 20 21#### System options specific to the x68k port 22 23options EXTENDED_MEMORY # support for >16MB memory 24options FPU_EMULATE # software fpu emulation for MC68030 25options FPSP # floating point emulation for MC68040 26options M060SP # int/fp emulation for MC68060 27options JUPITER # support for "Jupiter-X" accelerator 28options MAPPEDCOPY # use page mapping for large copyin/copyout 29options ZSCONSOLE,ZSCN_SPEED="9600" # use serial console 30 31 32#### System options that are the same for all ports 33 34## Root device configuration: change the ?'s if you are going to use a 35## nonstandard root partition (other than where the kernel is booted from) 36## and/or nonstandard root type (not ffs or nfs). Normally this can be 37## automagically determined at boot time. 38 39config netbsd root on ? type ? 40#config netbsd root on sd0 type ffs 41 42## RTC is offset from GMT; -540 means JST-9 43options RTC_OFFSET=-540 # hardware clock is this many mins. west of GMT 44 45## System call tracing (see ktrace(1)). 46options KTRACE 47 48## Collect statistics on kernel malloc's and free's. This does have a 49## significant performance hit on slower machines, so it is intended for 50## diagnostic use only. 51#options KMEMSTATS 52 53## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 54options SYSVMSG # System V message queues 55options SYSVSEM # System V semaphores 56options SYSVSHM # System V shared memory 57#options SHMMAXPGS=1024 # 1024 pages is the default 58 59## Loadable kernel module support 60#options LKM 61 62## NFS boot options; not supported currently: needs nfsboot program 63#options NFS_BOOT_BOOTPARAM 64#options NFS_BOOT_BOOTP 65#options NFS_BOOT_DHCP 66 67#### Debugging options 68 69## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 70## serial console break or keyboard reset, where the PROM would normally 71## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 72#options DDB # kernel dynamic debugger 73#options DDB_HISTORY_SIZE=100 # enable history editing in DDB 74#options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 75#options PANICBUTTON # interrupt switch invokes DDB 76 77## You may also use gdb, on another computer connected to this machine over 78## a serial port. Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is 79## a dev_t encoded device number of the serial port to use. 80## KGDB is not supported for now. 81#options KGDB # support for kernel gdb 82#options KGDBDEV=0xc00 # kgdb device number 83#options KGDBRATE=9600 # baud rate 84 85## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 86## such that gdb(1) can be used on a kernel coredump. 87 88#makeoptions DEBUG="-g" 89 90## Adds code to the kernel that does internal consistency checks, and will 91## cause the kernel to panic if corruption of internal data structures 92## is detected. 93#options DIAGNOSTIC # extra kernel sanity checking 94 95## Enable (possibly expensive) debugging code that may also display messages 96## on the system console 97#options DEBUG 98 99## Make SCSI error messages more verbose when explaining their meanings. 100options SCSIVERBOSE 101 102## `INSECURE' turns off the kernel security level (securelevel = 0 always). 103## This allows writing to /dev/mem, loading kernel modules while multi-user, 104## and other insecurities good only for development work. Do not use this 105## option on a production machine. 106#options INSECURE 107 108## Allow non-root users to grab /dev/console with programs such as xconsole. 109## `xconsole' therefore does not need setuid root with this option enabled. 110#options UCONSOLE 111 112## `FDSCRIPTS' allows non-readable but executable scripts by providing a 113## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 114## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 115## opaque file mechanism. Perl calls this "secure setuid scripts." 116 117#options FDSCRIPTS 118#options SETUIDSCRIPTS 119 120## Options for compatibility with previous releases foreign system binaries. 121 122options COMPAT_43 # 4.3BSD system interfaces 123options COMPAT_09 # NetBSD 0.9 binary compatibility 124options COMPAT_10 # NetBSD 1.0 binary compatibility 125options COMPAT_11 # NetBSD 1.1 binary compatibility 126options COMPAT_12 # NetBSD 1.2 binary compatibility 127options COMPAT_13 # NetBSD 1.3 binary compatibility 128options COMPAT_14 # NetBSD 1.4 binary compatibility 129#options COMPAT_M68K4K # NetBSD/m68k4k binaries 130#options COMPAT_SUNOS # SunOS 4.x binary compatibility; broken 131#options COMPAT_SVR4 # SVR4 binary compatibility; broken 132#options COMPAT_LINUX # Linux/m68k binary compatibility 133#options EXEC_ELF32 # 32-bit ELF executables (Linux, SVR4) 134 135## File systems. 136file-system FFS # Berkeley Fast Filesystem 137file-system NFS # Sun NFS-compatible filesystem client 138file-system KERNFS # kernel data-structure filesystem 139#file-system NULLFS # NULL layered filesystem (buggy) 140file-system MFS # memory-based filesystem 141#file-system FDESC # user file descriptor filesystem 142file-system UMAPFS # uid/gid remapping filesystem 143#file-system LFS # Log-structured filesystem (experimental) 144#file-system PORTAL # portal filesystem (experimental) 145file-system PROCFS # /proc 146file-system CD9660 # ISO 9660 + Rock Ridge file system 147#file-system UNION # union file system (a little buggy) 148file-system MSDOSFS # MS-DOS FAT filesystem(s). 149#file-system ADOSFS # AmigaDOS filesystem 150 151## File system options. 152options NFSSERVER # Sun NFS-compatible filesystem server 153options QUOTA # FFS quotas 154#options FFS_EI # FFS Endian Independent support 155 156## Network protocol support. In most environments, INET is required. 157options INET # IP (Internet Protocol) v4 158options TCP_COMPAT_42 # 4.2BSD IP implementation compatibility 159#options GATEWAY # packet forwarding ("router switch") 160#options MROUTING # packet forwarding of multicast packets 161#options DIRECTED_BROADCAST # allow broadcasts through routers 162#options NS # Xerox NS networking 163#options NSIP # Xerox NS tunneling over IP 164#options ISO,TPIP # OSI networking 165#options EON # OSI tunneling over IP 166#options CCITT,LLC,HDLC # X.25 packet switched protocol 167options NETATALK # AppleTalk (over Ethernet) protocol 168options NTP # Network Time Protocol in-kernel support 169#options PPS_SYNC # Add serial line synchronization for NTP 170#options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 171options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 172#options PPP_BSDCOMP # Add BSD compression to ppp device 173#options PPP_DEFLATE # Add deflate (libz) compression to ppp device 174#options PPP_FILTER # Add active filters for ppp (via bpf) 175 176 177 178#### Device configurations 179 180## Fundamental devices; see also std.x68k 181dmac0 at intio0 addr 0xe84000 # DMA controler 182xel0 at intio0 183opm0 at intio0 addr 0xe90000 # OPM: required for fdc 184 185## Display devices and console 186grfbus0 at mainbus0 # bitmapped displays 187grf0 at grfbus0 # multiplane graphics 188grf1 at grfbus0 # flexible graphics 189 190#kbd0 at mfp0 # standard keyboard 191#ite0 at grf0 # internal terminal emulator 192#options ITE_KERNEL_ATTR=4 # bold for kernel messages 193 # see /sys/arch/x68k/dev/itevar.h 194pseudo-device pow 2 # software power switch 195 196## floppy disks 197fdc0 at intio0 addr 0xe94000 intr 96 dma 0 dmaintr 100 # floppy controler 198fd* at fdc0 unit ? # builtin floppy drives 199 200## SCSI devices 201scsirom0 at intio0 addr 0xfc0000 # Built-in SCSI BIOS 202scsirom1 at intio0 addr 0xea0020 # External SCSI BIOS 203spc0 at scsirom0 # genuin SCSI 204spc1 at scsirom1 # genuin SCSI 205scsibus* at spc? 206mha0 at scsirom1 # Mankai MK-HA1 (Mach-2) 207scsibus* at mha0 208 209sd* at scsibus? target ? lun ? # SCSI disks 210cd* at scsibus? target ? lun ? # SCSI CD-ROMs 211st* at scsibus? target ? lun ? # SCSI tapes 212#ss* at scsibus? target ? lun ? # SCSI scanners 213ch* at scsibus? target ? lun ? # SCSI changer devices 214#uk* at scsibus? target ? lun ? # SCSI unknown devices 215 216## Serial ports 217zsc0 at intio0 addr 0xe98000 intr 112 218zstty0 at zsc0 channel 0 # built-in RS-232C 219ms0 at zsc0 channel 1 # standard mouse 220#zsc1 at intio0 addr 0xeafc00 intr 113 221#zstty2 at zsc1 channel 0 222#zstty3 at zsc1 channel 1 223#zsc2 at intio0 addr 0xeafc10 intr 114 224#zstty4 at zsc2 channel 0 225#zstty5 at zsc2 channel 1 226 227pseudo-device sram # battery-backuped static RAM 228pseudo-device bell # OPM bell 229 230xcom0 at mainbus0 # NS16550 fast serial 231xcom1 at mainbus0 232 233par0 at mainbus0 # Builtin printer port 234 235## Audio device; broken 236#okiadpcm0 at intio0 addr 0xe92000 intr 106 errintr 107 dma 3 237#audio* at okiadpcm* 238 239## Network interfaces 240neptune0 at intio0 addr 0xece000 intr 249 # Neptune-X 241neptune1 at intio0 addr 0xece400 intr 249 # Neptune-X at alt. addr. 242ne0 at neptune? addr 0x300 # NE2000 or clone 243#se0 at scsibus? target ? lun ? # Ether+; broken 244 245 246#### Pseudo devices 247 248## A disk-like interface to files. Can be used to create floppy, CD, 249## miniroot images, etc. 250 251pseudo-device vnd 4 252 253## Concatenated and striped disks; with this, you can create a software-based 254## disk array similar to a "RAID 0" setup. See ccd(4). 255 256pseudo-device ccd 4 257 258## RAIDframe disk driver: software RAID driver. See raid(4). 259 260pseudo-device raid 4 261 262## Memory disk device, used on boot floppies with compressed 263## kernel-plus-root-disk images. 264 265#pseudo-device md 1 266 267## Loopback network interface; required 268pseudo-device loop 269 270## SLIP and CSLIP interfaces, for IP over a serial line. 271pseudo-device sl 1 272 273## PPP, the successor to SLIP. See pppd(8). 274pseudo-device ppp 1 275 276## Network "tunnel" device, allowing protocol stacks to run in the userland. 277## This is used by the third-party user-mode "ppp" program, and others. 278pseudo-device tun 4 279 280## Generic L3 over IP tunnel 281#pseudo-device gre 2 # generic L3 over IP tunnel 282 283## Berkeley Packet Filter, required to run RARPD. A generic C-language 284## interface that allows selective examining of incoming packets. 285pseudo-device bpfilter 8 286 287## IP Filter, used in firewall and NAT applications. See ipnat(8) for 288## one example of the use of the IP Filter. 289pseudo-device ipfilter 290 291 292#### Other device configuration 293 294## Pseudo ttys, required for network logins and programs like screen. 295## 32 is a good number for average systems; you may have as many as you 296## like, though 256 is more or less the upper limit. Increasing this 297## number still requires you to run /dev/MAKEDEV to create the files 298## for the ptys. 299 300pseudo-device pty 32 # pseudo-ttys (for network, etc.) 301 302## Random device, used to implement /dev/random (a source of random noise), 303## and generate randomness for some kernel formulae. 304 305pseudo-device rnd 306