xref: /src/sys/dev/cadence/cemacreg.h

/*      $NetBSD: cemacreg.h,v 1.6 2024/08/28 06:50:17 skrll Exp $	*/

/*-
 * Copyright (c) 2015  Genetec Corporation.  All rights reserved.
 * Written by Hashimoto Kenichi for Genetec Corporation.
 *
 * Copyright (c) 2007 Embedtronics Oy
 * All rights reserved
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 * SUCH DAMAGE.
 *
 */

#ifndef	_IF_CEMACREG_H_
#define	_IF_CEMACREG_H_

/* Ethernet MAC (EMAC),
 * at91rm9200.pdf, page 573 */

#define	ETH_CTL		0x00U	/* Control Register			*/
#define	ETH_CFG		0x04U	/* Configuration Register		*/
#define	ETH_SR		0x08U	/* Status Register			*/
#define	ETH_TAR		0x0CU	/* Transmit Address Register (at91rm9200 only)	*/
#define	ETH_TCR		0x10U	/* Transmit Control Register (at91rm9200 only)	*/
#define	ETH_TSR		0x14U	/* Transmit Status Register		*/
#define	ETH_RBQP	0x18U	/* Receive Buffer Queue Pointer		*/
#define	ETH_TBQP	0x1CU	/* Transmit Buffer Queue Pointer	*/
#define	ETH_RSR		0x20U	/* Receive Status Register		*/
#define	ETH_ISR		0x24U	/* Interrupt Status Register		*/
#define	ETH_IER		0x28U	/* Interrupt Enable Register		*/
#define	ETH_IDR		0x2CU	/* Interrupt Disable Register		*/
#define	ETH_IMR		0x30U	/* Interrupt Mask Register		*/
#define	ETH_MAN		0x34U	/* PHY Maintenance Register		*/

#define	ETH_FRA		0x40U	/* Frames Transmitted OK		*/
#define	ETH_SCOL	0x44U	/* Single Collision Frames		*/
#define	ETH_MCOL	0x48U	/* Multiple Collision Frames		*/
#define	ETH_OK		0x4CU	/* Frames Received OK			*/
#define	ETH_SEQE	0x50U	/* Frame Check Sequence Errors		*/
#define	ETH_ALE		0x54U	/* Alignment Errors			*/
#define	ETH_DTE		0x58U	/* Deferred Transmission Frame		*/
#define	ETH_LCOL	0x5CU	/* Late Collisions			*/
#define	ETH_ECOL	0x60U	/* Excessive Collisions			*/
#define	ETH_CSE		0x64U	/* Carrier Sense Errors			*/
#define	ETH_TUE		0x68U	/* Transmit Underrun Errors		*/
#define	ETH_CDE		0x6CU	/* Code Errors				*/
#define	ETH_ELR		0x70U	/* Excessive Length Errors		*/
#define	ETH_RJB		0x74U	/* Receive Jabbers			*/
#define	ETH_USF		0x78U	/* Undersize Frames			*/
#define	ETH_SQEE	0x7CU	/* SQE Test Errors			*/
#define	ETH_DRFC	0x80U	/* Discarded RX Frames			*/

#define	ETH_HSH		0x90U	/* Hash Address High			*/
#define	ETH_HSL		0x94U	/* Hash Address Low			*/

#define	ETH_SA1L	0x98U	/* Specific Address 1 Low		*/
#define	ETH_SA1H	0x9CU	/* Specific Address 1 High		*/

#define	ETH_SA2L	0xA0U	/* Specific Address 2 Low		*/
#define	ETH_SA2H	0xA4U	/* Specific Address 2 High		*/

#define	ETH_SA3L	0xA8U	/* Specific Address 3 Low		*/
#define	ETH_SA3H	0xACU	/* Specific Address 3 High		*/

#define	ETH_SA4L	0xB0U	/* Specific Address 4 Low		*/
#define	ETH_SA4H	0xB4U	/* Specific Address 4 High		*/

/*
 * Gigabit Ethernet Controller (GEM)
 * ug585-Zynq-7000-TRM.pdf
 */

#define GEM_USER_IO	0x000C
#define GEM_DMA_CFG	0x0010	/* DMA Configuration */
#define  GEM_DMA_CFG_DISC_WHEN_NO_AHB		__BIT(24)
#define  GEM_DMA_CFG_RX_BUF_SIZE		__BITS(23, 16)
#define  GEM_DMA_CFG_CHKSUM_GEN_OFFLOAD_EN	__BIT(11)
#define  GEM_DMA_CFG_TX_PKTBUF_MEMSZ_SEL	__BIT(10)
#define  GEM_DMA_CFG_RX_PKTBUF_MEMSZ_SEL	__BITS(9, 8)
#define  GEM_DMA_CFG_AHB_ENDIAN_SWAP_PKT_EN	__BIT(7)
#define  GEM_DMA_CFG_AHB_ENDIAN_SWAP_MGMT_EN	__BIT(6)
#define  GEM_DMA_CFG_AHB_FIXED_BURST_LEN	__BITS(4, 0)
#define GEM_HSH		0x0080
#define GEM_HSL		0x0084
#define	GEM_SA1L	0x0088
#define	GEM_SA1H	0x008C
#define	GEM_SA2L	0x0090
#define	GEM_SA2H	0x0094
#define	GEM_SA3L	0x0098
#define	GEM_SA3H	0x009C
#define	GEM_SA4L	0x0090
#define	GEM_SA4H	0x0094
#define	GEM_SCOL	0x0138
#define	GEM_MCOL	0x013C
#define	GEM_DCFG2	0x0284
#define	GEM_DCFG3	0x0288
#define	GEM_DCFG4	0x028C
#define	GEM_DCFG5	0x0290

#define ETH_SIZE	0x1000

/* Control Register bits: */
#define GEM_CTL_ZEROPAUSETX	__BIT(12)
#define GEM_CTL_PAUSETX		__BIT(11)
#define GEM_CTL_HALTTX		__BIT(10)
#define GEM_CTL_STARTTX		__BIT(9)

#define	ETH_CTL_BP	__BIT(8)  /* 1 = back pressure enabled		      */
#define	ETH_CTL_WES	__BIT(7)  /* 1 = statistics registers writeable	      */
#define	ETH_CTL_ISR	__BIT(6)  /* 1 = increment statistics registers	      */
#define	ETH_CTL_CSR	__BIT(5)  /* 1 = clear statistics registers	      */
#define	ETH_CTL_MPE	__BIT(4)  /* 1 = management port enabled	      */
#define	ETH_CTL_TE	__BIT(3)  /* 1 = transmit enable		      */
#define	ETH_CTL_RE	__BIT(2)  /* 1 = receive enable			      */
#define	ETH_CTL_LBL	__BIT(1)  /* 1 = local loopback enabled		      */
#define	ETH_CTL_LB	__BIT(0)  /* 1 = loopback signal is at high level     */


/* Configuration Register bits: */
#define	ETH_CFG_RMII	__BIT(13)  /* 1 = enable RMII (Reduce MII) (AT91RM9200 only) */
#define	ETH_CFG_RTY	__BIT(12)	/* 1 = retry test enabled		*/

#define	ETH_CFG_CLK	0x0C00U	/* clock				*/
#define	ETH_CFG_CLK_8	0x0000U
#define	ETH_CFG_CLK_16	0x0400U
#define	ETH_CFG_CLK_32	0x0800U
#define	ETH_CFG_CLK_64	0x0C00U

#define	ETH_CFG_EAE	__BIT(9)	/* 1 = external address match enable	*/
#define	ETH_CFG_BIG	__BIT(8)	/* 1 = receive up to 1522 bytes	(VLAN)	*/
#define	ETH_CFG_UNI	__BIT(7)	/* 1 = enable unicast hash		*/
#define	ETH_CFG_MTI	__BIT(6)	/* 1 = enable multicast hash		*/
#define	ETH_CFG_NBC	__BIT(5)	/* 1 = ignore received broadcasts	*/
#define	ETH_CFG_CAF	__BIT(4)	/* 1 = receive all valid frames		*/
#define	ETH_CFG_BR	__BIT(2)
#define	ETH_CFG_FD	__BIT(1)	/* 1 = force full duplex		*/
#define	ETH_CFG_SPD	__BIT(0)	/* 1 = 100 Mbps				*/

#define GEM_CFG_GEN	__BIT(10)
#define GEM_CFG_CLK	__BITS(20, 18)
#define GEM_CFG_CLK_8	__SHIFTIN(0, GEM_CFG_CLK)
#define GEM_CFG_CLK_16	__SHIFTIN(1, GEM_CFG_CLK)
#define GEM_CFG_CLK_32	__SHIFTIN(2, GEM_CFG_CLK)
#define GEM_CFG_CLK_48	__SHIFTIN(3, GEM_CFG_CLK)
#define GEM_CFG_CLK_64	__SHIFTIN(4, GEM_CFG_CLK)
#define GEM_CFG_CLK_96	__SHIFTIN(5, GEM_CFG_CLK)
#define GEM_CFG_DBW	__BITS(22, 21)
#define	GEM_CFG_RXCOEN	__BIT(24)

/* Status Register bits: */
#define	ETH_SR_IDLE	__BIT(2)	/* 1 = PHY logic is running		*/
#define	ETH_SR_MDIO	__BIT(1)	/* 1 = MDIO pin set			*/
#define	ETH_SR_LINK	__BIT(0)


/* Transmit Control Register bits: */
#define	ETH_TCR_NCRC	0x8000U	/* 1 = don't append CRC			*/
#define	ETH_TCR_LEN	0x07FFU	/* transmit frame length		*/


/* Transmit Status Register bits: */
#define	ETH_TSR_UND	__BIT(6)	/* 1 = transmit underrun detected	*/
#define	ETH_TSR_COMP	__BIT(5)	/* 1 = transmit complete		*/
#define	ETH_TSR_BNQ	__BIT(4)	/* 1 = transmit buffer not queued (at91rm9200 only)	*/
#define	ETH_TSR_IDLE	__BIT(3)	/* 1 = transmitter idle			*/
#define	ETH_TSR_RLE	__BIT(2)	/* 1 = retry limit exceeded		*/
#define	ETH_TSR_COL	__BIT(1)	/* 1 = collision occurred		*/
#define	ETH_TSR_OVR	__BIT(0)	/* 1 = transmit buffer overrun		*/

#define	GEM_TSR_TXGO	__BIT(3)

/* Receive Status Register bits: */
#define	ETH_RSR_OVR	__BIT(2)	/* 1 = RX overrun			*/
#define	ETH_RSR_REC	__BIT(1)	/* 1 = frame received			*/
#define	ETH_RSR_BNA	__BIT(0)	/* 1 = buffer not available		*/


/* Interrupt bits: */
#define	ETH_ISR_ABT	__BIT(11)	/* 1 = abort during DMA transfer	*/
#define	ETH_ISR_ROVR	__BIT(10)	/* 1 = RX overrun			*/
#define	ETH_ISR_LINK	__BIT(9)	/* 1 = link pin changed			*/
#define	ETH_ISR_TIDLE	__BIT(8)	/* 1 = transmitter idle			*/
#define	ETH_ISR_TCOM	__BIT(7)	/* 1 = transmit complete		*/
#define	ETH_ISR_TBRE	__BIT(6)	/* 1 = transmit buffer register empty	*/
#define	ETH_ISR_RTRY	__BIT(5)	/* 1 = retry limit exceeded		*/
#define	ETH_ISR_TUND	__BIT(4)	/* 1 = transmit buffer underrun		*/
#define	ETH_ISR_TOVR	__BIT(3)	/* 1 = transmit buffer overrun		*/
#define	ETH_ISR_RBNA	__BIT(2)	/* 1 = receive buffer not available	*/
#define	ETH_ISR_RCOM	__BIT(1)	/* 1 = receive complete			*/
#define	ETH_ISR_DONE	__BIT(0)	/* 1 = management done			*/


/* PHY Maintenance Register bits: */
#define	ETH_MAN_LOW	__BIT(31) /* must not be set			*/
#define	ETH_MAN_HIGH	__BIT(30) /* must be set			*/

#define	ETH_MAN_RW	__BITS(29, 28)
#define	ETH_MAN_RW_RD	__BIT(29)
#define	ETH_MAN_RW_WR	__BIT(28)

#define	ETH_MAN_PHYA	0x0F800000U /* PHY address (normally 0)		*/
#define	ETH_MAN_PHYA_SHIFT 23U
#define	ETH_MAN_REGA	0x007C0000U
#define	ETH_MAN_REGA_SHIFT 18U
#define	ETH_MAN_CODE	0x00030000U /* must be 10			*/
#define	ETH_MAN_CODE_IEEE802_3 \
			0x00020000U
#define	ETH_MAN_DATA	0x0000FFFFU /* data to be written to the PHY	*/

#define	ETH_MAN_VAL	(ETH_MAN_HIGH|ETH_MAN_CODE_IEEE802_3)


/* received buffer descriptor: */
#define	ETH_DSC_ADDR		0x00U
#define	ETH_DSC_FLAGS		0x00U
#define	ETH_DSC_INFO		0x04U
#define	ETH_DSC_SIZE		0x08U

typedef struct eth_dsc {
	volatile uint32_t	Addr;
	volatile uint32_t	Info;
} __attribute__ ((aligned(4))) eth_dsc_t;

/* flags: */
#define	ETH_RDSC_F_WRAP		__BIT(1)
#define	ETH_RDSC_F_USED		__BIT(0)

/* frame info bits: */
#define	ETH_RDSC_I_BCAST	__BIT(31)
#define	ETH_RDSC_I_MULTICAST	__BIT(30)
#define	ETH_RDSC_I_UNICAST	__BIT(29)
#define	ETH_RDSC_I_VLAN		__BIT(28)
#define	ETH_RDSC_I_UNKNOWN_SRC	__BIT(27)
#define	ETH_RDSC_I_MATCH1	__BIT(26)
#define	ETH_RDSC_I_MATCH2	__BIT(25)
#define	ETH_RDSC_I_MATCH3	__BIT(24)
#define	ETH_RDSC_I_MATCH4	__BIT(23)
#define	ETH_RDSC_I_CHKSUM	__BITS(23, 22)
#define	ETH_RDSC_I_CHKSUM_NONE	__SHIFTIN(0, ETH_RDSC_I_CHKSUM)
#define	ETH_RDSC_I_CHKSUM_IP	__SHIFTIN(1, ETH_RDSC_I_CHKSUM)
#define	ETH_RDSC_I_CHKSUM_TCP	__SHIFTIN(2, ETH_RDSC_I_CHKSUM)
#define	ETH_RDSC_I_CHKSUM_UDP	__SHIFTIN(3, ETH_RDSC_I_CHKSUM)
#define	ETH_RDSC_I_LEN		__BITS(13, 0)

#define ETH_TDSC_I_USED				__BIT(31)	/* done transmitting */
#define ETH_TDSC_I_WRAP				__BIT(30)	/* end of descr ring */
#define ETH_TDSC_I_RETRY_ERR			__BIT(29)
#define ETH_TDSC_I_AHB_ERR			__BIT(27)
#define ETH_TDSC_I_LATE_COLL			__BIT(26)
#define	ETH_TDSC_I_CHKSUM			__BITS(22, 20)
#define ETH_TDSC_I_CHKSUM_GEN_STAT_NO_ERR	__SHIFTIN(0, ETH_TDSC_I_CHKSUM)
#define ETH_TDSC_I_CHKSUM_GEN_STAT_VLAN_HDR_ERR	__SHIFTIN(1, ETH_TDSC_I_CHKSUM)
#define ETH_TDSC_I_CHKSUM_GEN_STAT_SNAP_HDR_ERR	__SHIFTIN(2, ETH_TDSC_I_CHKSUM)
#define ETH_TDSC_I_CHKSUM_GEN_STAT_IP_HDR_ERR	__SHIFTIN(3, ETH_TDSC_I_CHKSUM)
#define ETH_TDSC_I_CHKSUM_GEN_STAT_UNKNOWN_TYPE	__SHIFTIN(4, ETH_TDSC_I_CHKSUM)
#define ETH_TDSC_I_CHKSUM_GEN_STAT_UNSUPP_FRAG	__SHIFTIN(5, ETH_TDSC_I_CHKSUM)
#define ETH_TDSC_I_CHKSUM_GEN_STAT_NOT_TCPUDP	__SHIFTIN(6, ETH_TDSC_I_CHKSUM)
#define ETH_TDSC_I_CHKSUM_GEN_STAT_SHORT_PKT	__SHIFTIN(7, ETH_TDSC_I_CHKSUM)
#define ETH_TDSC_I_NO_CRC_APPENDED		__BIT(16)
#define ETH_TDSC_I_LAST_BUF			__BIT(15)	/* last buf in frame */
#define ETH_TDSC_I_LEN				__BITS(13, 0)

#endif /* !_IF_CEMACREG_H_ */