adwlib.c revision 1.39.4.1
1 /* $NetBSD: adwlib.c,v 1.39.4.1 2011/03/05 20:53:11 rmind Exp $ */ 2 3 /* 4 * Low level routines for the Advanced Systems Inc. SCSI controllers chips 5 * 6 * Copyright (c) 1998, 1999, 2000 The NetBSD Foundation, Inc. 7 * All rights reserved. 8 * 9 * Author: Baldassare Dante Profeta <dante (at) mclink.it> 10 * 11 * Redistribution and use in source and binary forms, with or without 12 * modification, are permitted provided that the following conditions 13 * are met: 14 * 1. Redistributions of source code must retain the above copyright 15 * notice, this list of conditions and the following disclaimer. 16 * 2. Redistributions in binary form must reproduce the above copyright 17 * notice, this list of conditions and the following disclaimer in the 18 * documentation and/or other materials provided with the distribution. 19 * 3. All advertising materials mentioning features or use of this software 20 * must display the following acknowledgement: 21 * This product includes software developed by the NetBSD 22 * Foundation, Inc. and its contributors. 23 * 4. Neither the name of The NetBSD Foundation nor the names of its 24 * contributors may be used to endorse or promote products derived 25 * from this software without specific prior written permission. 26 * 27 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS 28 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 29 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 30 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS 31 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 32 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 33 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 34 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 35 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 36 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 37 * POSSIBILITY OF SUCH DAMAGE. 38 */ 39 /* 40 * Ported from: 41 */ 42 /* 43 * advansys.c - Linux Host Driver for AdvanSys SCSI Adapters 44 * 45 * Copyright (c) 1995-2000 Advanced System Products, Inc. 46 * All Rights Reserved. 47 * 48 * Redistribution and use in source and binary forms, with or without 49 * modification, are permitted provided that redistributions of source 50 * code retain the above copyright notice and this comment without 51 * modification. 52 */ 53 54 #include <sys/cdefs.h> 55 __KERNEL_RCSID(0, "$NetBSD: adwlib.c,v 1.39.4.1 2011/03/05 20:53:11 rmind Exp $"); 56 57 #include <sys/param.h> 58 #include <sys/systm.h> 59 #include <sys/malloc.h> 60 #include <sys/kernel.h> 61 #include <sys/queue.h> 62 #include <sys/device.h> 63 64 #include <sys/bus.h> 65 #include <sys/intr.h> 66 67 #include <dev/scsipi/scsi_all.h> 68 #include <dev/scsipi/scsipi_all.h> 69 #include <dev/scsipi/scsiconf.h> 70 71 #include <dev/pci/pcidevs.h> 72 73 #include <dev/ic/adwlib.h> 74 #include <dev/ic/adwmcode.h> 75 #include <dev/ic/adw.h> 76 77 78 /* Static Functions */ 79 80 int AdwRamSelfTest(bus_space_tag_t, bus_space_handle_t, u_int8_t); 81 int AdwLoadMCode(bus_space_tag_t, bus_space_handle_t, u_int16_t *, u_int8_t); 82 int AdwASC3550Cabling(bus_space_tag_t, bus_space_handle_t, ADW_DVC_CFG *); 83 int AdwASC38C0800Cabling(bus_space_tag_t, bus_space_handle_t, ADW_DVC_CFG *); 84 int AdwASC38C1600Cabling(bus_space_tag_t, bus_space_handle_t, ADW_DVC_CFG *); 85 86 static u_int16_t AdwGetEEPROMConfig(bus_space_tag_t, bus_space_handle_t, 87 ADW_EEPROM *); 88 static void AdwSetEEPROMConfig(bus_space_tag_t, bus_space_handle_t, 89 ADW_EEPROM *); 90 static u_int16_t AdwReadEEPWord(bus_space_tag_t, bus_space_handle_t, int); 91 static void AdwWaitEEPCmd(bus_space_tag_t, bus_space_handle_t); 92 93 static void AdwInquiryHandling(ADW_SOFTC *, ADW_SCSI_REQ_Q *); 94 95 static void AdwSleepMilliSecond(u_int32_t); 96 static void AdwDelayMicroSecond(u_int32_t); 97 98 99 /* 100 * EEPROM Configuration. 101 * 102 * All drivers should use this structure to set the default EEPROM 103 * configuration. The BIOS now uses this structure when it is built. 104 * Additional structure information can be found in adwlib.h where 105 * the structure is defined. 106 */ 107 static const ADW_EEPROM adw_3550_Default_EEPROM = { 108 ADW_EEPROM_BIOS_ENABLE, /* 00 cfg_lsw */ 109 0x0000, /* 01 cfg_msw */ 110 0xFFFF, /* 02 disc_enable */ 111 0xFFFF, /* 03 wdtr_able */ 112 { 0xFFFF }, /* 04 sdtr_able */ 113 0xFFFF, /* 05 start_motor */ 114 0xFFFF, /* 06 tagqng_able */ 115 0xFFFF, /* 07 bios_scan */ 116 0, /* 08 scam_tolerant */ 117 7, /* 09 adapter_scsi_id */ 118 0, /* bios_boot_delay */ 119 3, /* 10 scsi_reset_delay */ 120 0, /* bios_id_lun */ 121 0, /* 11 termination */ 122 0, /* reserved1 */ 123 0xFFE7, /* 12 bios_ctrl */ 124 { 0xFFFF }, /* 13 ultra_able */ 125 { 0 }, /* 14 reserved2 */ 126 ADW_DEF_MAX_HOST_QNG, /* 15 max_host_qng */ 127 ADW_DEF_MAX_DVC_QNG, /* max_dvc_qng */ 128 0, /* 16 dvc_cntl */ 129 { 0 }, /* 17 bug_fix */ 130 { 0,0,0 }, /* 18-20 serial_number[3] */ 131 0, /* 21 check_sum */ 132 { /* 22-29 oem_name[16] */ 133 0,0,0,0,0,0,0,0, 134 0,0,0,0,0,0,0,0 135 }, 136 0, /* 30 dvc_err_code */ 137 0, /* 31 adv_err_code */ 138 0, /* 32 adv_err_addr */ 139 0, /* 33 saved_dvc_err_code */ 140 0, /* 34 saved_adv_err_code */ 141 0, /* 35 saved_adv_err_addr */ 142 { /* 36-55 reserved1[16] */ 143 0,0,0,0,0,0,0,0,0,0, 144 0,0,0,0,0,0,0,0,0,0 145 }, 146 0, /* 56 cisptr_lsw */ 147 0, /* 57 cisprt_msw */ 148 0, /* 58 subsysvid */ 149 0, /* 59 subsysid */ 150 { 0,0,0,0 } /* 60-63 reserved2[4] */ 151 }; 152 153 static const ADW_EEPROM adw_38C0800_Default_EEPROM = { 154 ADW_EEPROM_BIOS_ENABLE, /* 00 cfg_lsw */ 155 0x0000, /* 01 cfg_msw */ 156 0xFFFF, /* 02 disc_enable */ 157 0xFFFF, /* 03 wdtr_able */ 158 { 0x4444 }, /* 04 sdtr_speed1 */ 159 0xFFFF, /* 05 start_motor */ 160 0xFFFF, /* 06 tagqng_able */ 161 0xFFFF, /* 07 bios_scan */ 162 0, /* 08 scam_tolerant */ 163 7, /* 09 adapter_scsi_id */ 164 0, /* bios_boot_delay */ 165 3, /* 10 scsi_reset_delay */ 166 0, /* bios_id_lun */ 167 0, /* 11 termination_se */ 168 0, /* termination_lvd */ 169 0xFFE7, /* 12 bios_ctrl */ 170 { 0x4444 }, /* 13 sdtr_speed2 */ 171 { 0x4444 }, /* 14 sdtr_speed3 */ 172 ADW_DEF_MAX_HOST_QNG, /* 15 max_host_qng */ 173 ADW_DEF_MAX_DVC_QNG, /* max_dvc_qng */ 174 0, /* 16 dvc_cntl */ 175 { 0x4444 }, /* 17 sdtr_speed4 */ 176 { 0,0,0 }, /* 18-20 serial_number[3] */ 177 0, /* 21 check_sum */ 178 { /* 22-29 oem_name[16] */ 179 0,0,0,0,0,0,0,0, 180 0,0,0,0,0,0,0,0 181 }, 182 0, /* 30 dvc_err_code */ 183 0, /* 31 adv_err_code */ 184 0, /* 32 adv_err_addr */ 185 0, /* 33 saved_dvc_err_code */ 186 0, /* 34 saved_adv_err_code */ 187 0, /* 35 saved_adv_err_addr */ 188 { /* 36-55 reserved1[16] */ 189 0,0,0,0,0,0,0,0,0,0, 190 0,0,0,0,0,0,0,0,0,0 191 }, 192 0, /* 56 cisptr_lsw */ 193 0, /* 57 cisprt_msw */ 194 PCI_VENDOR_ADVSYS, /* 58 subsysvid */ 195 PCI_PRODUCT_ADVSYS_U2W, /* 59 subsysid */ 196 { 0,0,0,0 } /* 60-63 reserved2[4] */ 197 }; 198 199 static const ADW_EEPROM adw_38C1600_Default_EEPROM = { 200 ADW_EEPROM_BIOS_ENABLE, /* 00 cfg_lsw */ 201 0x0000, /* 01 cfg_msw */ 202 0xFFFF, /* 02 disc_enable */ 203 0xFFFF, /* 03 wdtr_able */ 204 { 0x5555 }, /* 04 sdtr_speed1 */ 205 0xFFFF, /* 05 start_motor */ 206 0xFFFF, /* 06 tagqng_able */ 207 0xFFFF, /* 07 bios_scan */ 208 0, /* 08 scam_tolerant */ 209 7, /* 09 adapter_scsi_id */ 210 0, /* bios_boot_delay */ 211 3, /* 10 scsi_reset_delay */ 212 0, /* bios_id_lun */ 213 0, /* 11 termination_se */ 214 0, /* termination_lvd */ 215 0xFFE7, /* 12 bios_ctrl */ 216 { 0x5555 }, /* 13 sdtr_speed2 */ 217 { 0x5555 }, /* 14 sdtr_speed3 */ 218 ADW_DEF_MAX_HOST_QNG, /* 15 max_host_qng */ 219 ADW_DEF_MAX_DVC_QNG, /* max_dvc_qng */ 220 0, /* 16 dvc_cntl */ 221 { 0x5555 }, /* 17 sdtr_speed4 */ 222 { 0,0,0 }, /* 18-20 serial_number[3] */ 223 0, /* 21 check_sum */ 224 { /* 22-29 oem_name[16] */ 225 0,0,0,0,0,0,0,0, 226 0,0,0,0,0,0,0,0 227 }, 228 0, /* 30 dvc_err_code */ 229 0, /* 31 adv_err_code */ 230 0, /* 32 adv_err_addr */ 231 0, /* 33 saved_dvc_err_code */ 232 0, /* 34 saved_adv_err_code */ 233 0, /* 35 saved_adv_err_addr */ 234 { /* 36-55 reserved1[16] */ 235 0,0,0,0,0,0,0,0,0,0, 236 0,0,0,0,0,0,0,0,0,0 237 }, 238 0, /* 56 cisptr_lsw */ 239 0, /* 57 cisprt_msw */ 240 PCI_VENDOR_ADVSYS, /* 58 subsysvid */ 241 PCI_PRODUCT_ADVSYS_U3W, /* 59 subsysid */ 242 { 0,0,0,0 } /* 60-63 reserved2[4] */ 243 }; 244 245 246 /* 247 * Read the board's EEPROM configuration. Set fields in ADW_SOFTC and 248 * ADW_DVC_CFG based on the EEPROM settings. The chip is stopped while 249 * all of this is done. 250 * 251 * For a non-fatal error return a warning code. If there are no warnings 252 * then 0 is returned. 253 * 254 * Note: Chip is stopped on entry. 255 */ 256 int 257 AdwInitFromEEPROM(ADW_SOFTC *sc) 258 { 259 bus_space_tag_t iot = sc->sc_iot; 260 bus_space_handle_t ioh = sc->sc_ioh; 261 ADW_EEPROM eep_config; 262 u_int16_t warn_code; 263 u_int16_t sdtr_speed = 0; 264 u_int8_t tid, termination; 265 int i, j; 266 267 268 warn_code = 0; 269 270 /* 271 * Read the board's EEPROM configuration. 272 * 273 * Set default values if a bad checksum is found. 274 * 275 * XXX - Don't handle big-endian access to EEPROM yet. 276 */ 277 if (AdwGetEEPROMConfig(iot, ioh, &eep_config) != eep_config.check_sum) { 278 warn_code |= ADW_WARN_EEPROM_CHKSUM; 279 280 /* 281 * Set EEPROM default values. 282 */ 283 switch(sc->chip_type) { 284 case ADW_CHIP_ASC3550: 285 eep_config = adw_3550_Default_EEPROM; 286 break; 287 case ADW_CHIP_ASC38C0800: 288 eep_config = adw_38C0800_Default_EEPROM; 289 break; 290 case ADW_CHIP_ASC38C1600: 291 eep_config = adw_38C1600_Default_EEPROM; 292 293 #if 0 294 XXX TODO!!! if (ASC_PCI_ID2FUNC(sc->cfg.pci_slot_info) != 0) { 295 #endif 296 if (sc->cfg.pci_slot_info != 0) { 297 u_int8_t lsw_msb; 298 299 lsw_msb = eep_config.cfg_lsw >> 8; 300 /* 301 * Set Function 1 EEPROM Word 0 MSB 302 * 303 * Clear the BIOS_ENABLE (bit 14) and 304 * INTAB (bit 11) EEPROM bits. 305 * 306 * Disable Bit 14 (BIOS_ENABLE) to fix 307 * SPARC Ultra 60 and old Mac system booting 308 * problem. The Expansion ROM must 309 * be disabled in Function 1 for these systems. 310 */ 311 lsw_msb &= ~(((ADW_EEPROM_BIOS_ENABLE | 312 ADW_EEPROM_INTAB) >> 8) & 0xFF); 313 /* 314 * Set the INTAB (bit 11) if the GPIO 0 input 315 * indicates the Function 1 interrupt line is 316 * wired to INTA. 317 * 318 * Set/Clear Bit 11 (INTAB) from 319 * the GPIO bit 0 input: 320 * 1 - Function 1 intr line wired to INT A. 321 * 0 - Function 1 intr line wired to INT B. 322 * 323 * Note: Adapter boards always have Function 0 324 * wired to INTA. 325 * Put all 5 GPIO bits in input mode and then 326 * read their input values. 327 */ 328 ADW_WRITE_BYTE_REGISTER(iot, ioh, 329 IOPB_GPIO_CNTL, 0); 330 if (ADW_READ_BYTE_REGISTER(iot, ioh, 331 IOPB_GPIO_DATA) & 0x01) { 332 /* 333 * Function 1 interrupt wired to INTA; 334 * Set EEPROM bit. 335 */ 336 lsw_msb |= (ADW_EEPROM_INTAB >> 8) 337 & 0xFF; 338 } 339 eep_config.cfg_lsw &= 0x00FF; 340 eep_config.cfg_lsw |= lsw_msb << 8; 341 } 342 break; 343 } 344 345 /* 346 * Assume the 6 byte board serial number that was read 347 * from EEPROM is correct even if the EEPROM checksum 348 * failed. 349 */ 350 for (i=2, j=1; i>=0; i--, j++) { 351 eep_config.serial_number[i] = 352 AdwReadEEPWord(iot, ioh, ASC_EEP_DVC_CFG_END - j); 353 } 354 355 AdwSetEEPROMConfig(iot, ioh, &eep_config); 356 } 357 /* 358 * Set sc and sc->cfg variables from the EEPROM configuration 359 * that was read. 360 * 361 * This is the mapping of EEPROM fields to Adw Library fields. 362 */ 363 sc->wdtr_able = eep_config.wdtr_able; 364 if (sc->chip_type == ADW_CHIP_ASC3550) { 365 sc->sdtr_able = eep_config.sdtr1.sdtr_able; 366 sc->ultra_able = eep_config.sdtr2.ultra_able; 367 } else { 368 sc->sdtr_speed1 = eep_config.sdtr1.sdtr_speed1; 369 sc->sdtr_speed2 = eep_config.sdtr2.sdtr_speed2; 370 sc->sdtr_speed3 = eep_config.sdtr3.sdtr_speed3; 371 sc->sdtr_speed4 = eep_config.sdtr4.sdtr_speed4; 372 } 373 sc->ppr_able = 0; 374 sc->tagqng_able = eep_config.tagqng_able; 375 sc->cfg.disc_enable = eep_config.disc_enable; 376 sc->max_host_qng = eep_config.max_host_qng; 377 sc->max_dvc_qng = eep_config.max_dvc_qng; 378 sc->chip_scsi_id = (eep_config.adapter_scsi_id & ADW_MAX_TID); 379 sc->start_motor = eep_config.start_motor; 380 sc->scsi_reset_wait = eep_config.scsi_reset_delay; 381 sc->bios_ctrl = eep_config.bios_ctrl; 382 sc->no_scam = eep_config.scam_tolerant; 383 sc->cfg.serial1 = eep_config.serial_number[0]; 384 sc->cfg.serial2 = eep_config.serial_number[1]; 385 sc->cfg.serial3 = eep_config.serial_number[2]; 386 387 if (sc->chip_type == ADW_CHIP_ASC38C0800 || 388 sc->chip_type == ADW_CHIP_ASC38C1600) { 389 sc->sdtr_able = 0; 390 for (tid = 0; tid <= ADW_MAX_TID; tid++) { 391 if (tid == 0) { 392 sdtr_speed = sc->sdtr_speed1; 393 } else if (tid == 4) { 394 sdtr_speed = sc->sdtr_speed2; 395 } else if (tid == 8) { 396 sdtr_speed = sc->sdtr_speed3; 397 } else if (tid == 12) { 398 sdtr_speed = sc->sdtr_speed4; 399 } 400 if (sdtr_speed & ADW_MAX_TID) { 401 sc->sdtr_able |= (1 << tid); 402 } 403 sdtr_speed >>= 4; 404 } 405 } 406 407 /* 408 * Set the host maximum queuing (max. 253, min. 16) and the per device 409 * maximum queuing (max. 63, min. 4). 410 */ 411 if (eep_config.max_host_qng > ADW_DEF_MAX_HOST_QNG) { 412 eep_config.max_host_qng = ADW_DEF_MAX_HOST_QNG; 413 } else if (eep_config.max_host_qng < ADW_DEF_MIN_HOST_QNG) 414 { 415 /* If the value is zero, assume it is uninitialized. */ 416 if (eep_config.max_host_qng == 0) { 417 eep_config.max_host_qng = ADW_DEF_MAX_HOST_QNG; 418 } else { 419 eep_config.max_host_qng = ADW_DEF_MIN_HOST_QNG; 420 } 421 } 422 423 if (eep_config.max_dvc_qng > ADW_DEF_MAX_DVC_QNG) { 424 eep_config.max_dvc_qng = ADW_DEF_MAX_DVC_QNG; 425 } else if (eep_config.max_dvc_qng < ADW_DEF_MIN_DVC_QNG) { 426 /* If the value is zero, assume it is uninitialized. */ 427 if (eep_config.max_dvc_qng == 0) { 428 eep_config.max_dvc_qng = ADW_DEF_MAX_DVC_QNG; 429 } else { 430 eep_config.max_dvc_qng = ADW_DEF_MIN_DVC_QNG; 431 } 432 } 433 434 /* 435 * If 'max_dvc_qng' is greater than 'max_host_qng', then 436 * set 'max_dvc_qng' to 'max_host_qng'. 437 */ 438 if (eep_config.max_dvc_qng > eep_config.max_host_qng) { 439 eep_config.max_dvc_qng = eep_config.max_host_qng; 440 } 441 442 /* 443 * Set ADV_DVC_VAR 'max_host_qng' and ADV_DVC_VAR 'max_dvc_qng' 444 * values based on possibly adjusted EEPROM values. 445 */ 446 sc->max_host_qng = eep_config.max_host_qng; 447 sc->max_dvc_qng = eep_config.max_dvc_qng; 448 449 450 /* 451 * If the EEPROM 'termination' field is set to automatic (0), then set 452 * the ADV_DVC_CFG 'termination' field to automatic also. 453 * 454 * If the termination is specified with a non-zero 'termination' 455 * value check that a legal value is set and set the ADV_DVC_CFG 456 * 'termination' field appropriately. 457 */ 458 459 switch(sc->chip_type) { 460 case ADW_CHIP_ASC3550: 461 sc->cfg.termination = 0; /* auto termination */ 462 switch(eep_config.termination_se) { 463 case 3: 464 /* Enable manual control with low on / high on. */ 465 sc->cfg.termination |= ADW_TERM_CTL_L; 466 case 2: 467 /* Enable manual control with low off / high on. */ 468 sc->cfg.termination |= ADW_TERM_CTL_H; 469 case 1: 470 /* Enable manual control with low off / high off. */ 471 sc->cfg.termination |= ADW_TERM_CTL_SEL; 472 case 0: 473 break; 474 default: 475 warn_code |= ADW_WARN_EEPROM_TERMINATION; 476 } 477 break; 478 479 case ADW_CHIP_ASC38C0800: 480 case ADW_CHIP_ASC38C1600: 481 switch(eep_config.termination_se) { 482 case 0: 483 /* auto termination for SE */ 484 termination = 0; 485 break; 486 case 1: 487 /* Enable manual control with low off / high off. */ 488 termination = 0; 489 break; 490 case 2: 491 /* Enable manual control with low off / high on. */ 492 termination = ADW_TERM_SE_HI; 493 break; 494 case 3: 495 /* Enable manual control with low on / high on. */ 496 termination = ADW_TERM_SE; 497 break; 498 default: 499 /* 500 * The EEPROM 'termination_se' field contains a 501 * bad value. Use automatic termination instead. 502 */ 503 termination = 0; 504 warn_code |= ADW_WARN_EEPROM_TERMINATION; 505 } 506 507 switch(eep_config.termination_lvd) { 508 case 0: 509 /* auto termination for LVD */ 510 sc->cfg.termination = termination; 511 break; 512 case 1: 513 /* Enable manual control with low off / high off. */ 514 sc->cfg.termination = termination; 515 break; 516 case 2: 517 /* Enable manual control with low off / high on. */ 518 sc->cfg.termination = termination | ADW_TERM_LVD_HI; 519 break; 520 case 3: 521 /* Enable manual control with low on / high on. */ 522 sc->cfg.termination = termination | ADW_TERM_LVD; 523 break; 524 default: 525 /* 526 * The EEPROM 'termination_lvd' field contains a 527 * bad value. Use automatic termination instead. 528 */ 529 sc->cfg.termination = termination; 530 warn_code |= ADW_WARN_EEPROM_TERMINATION; 531 } 532 break; 533 } 534 535 return warn_code; 536 } 537 538 539 /* 540 * Initialize the ASC-3550/ASC-38C0800/ASC-38C1600. 541 * 542 * On failure return the error code. 543 */ 544 int 545 AdwInitDriver(ADW_SOFTC *sc) 546 { 547 bus_space_tag_t iot = sc->sc_iot; 548 bus_space_handle_t ioh = sc->sc_ioh; 549 u_int16_t error_code; 550 int word; 551 int i; 552 u_int16_t bios_mem[ADW_MC_BIOSLEN/2]; /* BIOS RISC Memory 553 0x40-0x8F. */ 554 u_int16_t wdtr_able = 0, sdtr_able, ppr_able, tagqng_able; 555 u_int8_t max_cmd[ADW_MAX_TID + 1]; 556 u_int8_t tid; 557 558 559 error_code = 0; 560 561 /* 562 * Save the RISC memory BIOS region before writing the microcode. 563 * The BIOS may already be loaded and using its RISC LRAM region 564 * so its region must be saved and restored. 565 * 566 * Note: This code makes the assumption, which is currently true, 567 * that a chip reset does not clear RISC LRAM. 568 */ 569 for (i = 0; i < ADW_MC_BIOSLEN/2; i++) { 570 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_BIOSMEM+(2*i), bios_mem[i]); 571 } 572 573 /* 574 * Save current per TID negotiated values. 575 */ 576 switch (sc->chip_type) { 577 case ADW_CHIP_ASC3550: 578 if (bios_mem[(ADW_MC_BIOS_SIGNATURE-ADW_MC_BIOSMEM)/2]==0x55AA){ 579 580 u_int16_t bios_version, major, minor; 581 582 bios_version = bios_mem[(ADW_MC_BIOS_VERSION - 583 ADW_MC_BIOSMEM) / 2]; 584 major = (bios_version >> 12) & 0xF; 585 minor = (bios_version >> 8) & 0xF; 586 if (major < 3 || (major == 3 && minor == 1)) { 587 /* 588 * BIOS 3.1 and earlier location of 589 * 'wdtr_able' variable. 590 */ 591 ADW_READ_WORD_LRAM(iot, ioh, 0x120, wdtr_able); 592 } else { 593 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_WDTR_ABLE, 594 wdtr_able); 595 } 596 } 597 break; 598 599 case ADW_CHIP_ASC38C1600: 600 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_PPR_ABLE, ppr_able); 601 /* FALLTHROUGH */ 602 case ADW_CHIP_ASC38C0800: 603 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_WDTR_ABLE, wdtr_able); 604 break; 605 } 606 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_SDTR_ABLE, sdtr_able); 607 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_TAGQNG_ABLE, tagqng_able); 608 for (tid = 0; tid <= ADW_MAX_TID; tid++) { 609 ADW_READ_BYTE_LRAM(iot, ioh, ADW_MC_NUMBER_OF_MAX_CMD + tid, 610 max_cmd[tid]); 611 } 612 613 /* 614 * Perform a RAM Built-In Self Test 615 */ 616 if((error_code = AdwRamSelfTest(iot, ioh, sc->chip_type))) { 617 return error_code; 618 } 619 620 /* 621 * Load the Microcode 622 */ 623 ; 624 if((error_code = AdwLoadMCode(iot, ioh, bios_mem, sc->chip_type))) { 625 return error_code; 626 } 627 628 /* 629 * Read microcode version and date. 630 */ 631 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_VERSION_DATE, sc->cfg.mcode_date); 632 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_VERSION_NUM, sc->cfg.mcode_version); 633 634 /* 635 * If the PCI Configuration Command Register "Parity Error Response 636 * Control" Bit was clear (0), then set the microcode variable 637 * 'control_flag' CONTROL_FLAG_IGNORE_PERR flag to tell the microcode 638 * to ignore DMA parity errors. 639 */ 640 if (sc->cfg.control_flag & CONTROL_FLAG_IGNORE_PERR) { 641 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_CONTROL_FLAG, word); 642 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_CONTROL_FLAG, 643 word | CONTROL_FLAG_IGNORE_PERR); 644 } 645 646 switch (sc->chip_type) { 647 case ADW_CHIP_ASC3550: 648 /* 649 * For ASC-3550, setting the START_CTL_EMFU [3:2] bits sets a 650 * FIFO threshold of 128 bytes. 651 * This register is only accessible to the host. 652 */ 653 ADW_WRITE_BYTE_REGISTER(iot, ioh, IOPB_DMA_CFG0, 654 START_CTL_EMFU | READ_CMD_MRM); 655 break; 656 657 case ADW_CHIP_ASC38C0800: 658 /* 659 * Write 1 to bit 14 'DIS_TERM_DRV' in the SCSI_CFG1 register. 660 * When DIS_TERM_DRV set to 1, C_DET[3:0] will reflect current 661 * cable detection and then we are able to read C_DET[3:0]. 662 * 663 * Note: We will reset DIS_TERM_DRV to 0 in the 'Set SCSI_CFG1 664 * Microcode Default Value' section below. 665 */ 666 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_SCSI_CFG1, 667 ADW_READ_WORD_REGISTER(iot, ioh, IOPW_SCSI_CFG1) 668 | ADW_DIS_TERM_DRV); 669 670 /* 671 * For ASC-38C0800, set FIFO_THRESH_80B [6:4] bits and 672 * START_CTL_TH [3:2] bits for the default FIFO threshold. 673 * 674 * Note: ASC-38C0800 FIFO threshold has been changed to 675 * 256 bytes. 676 * 677 * For DMA Errata #4 set the BC_THRESH_ENB bit. 678 */ 679 ADW_WRITE_BYTE_REGISTER(iot, ioh, IOPB_DMA_CFG0, 680 BC_THRESH_ENB | FIFO_THRESH_80B 681 | START_CTL_TH | READ_CMD_MRM); 682 break; 683 684 case ADW_CHIP_ASC38C1600: 685 /* 686 * Write 1 to bit 14 'DIS_TERM_DRV' in the SCSI_CFG1 register. 687 * When DIS_TERM_DRV set to 1, C_DET[3:0] will reflect current 688 * cable detection and then we are able to read C_DET[3:0]. 689 * 690 * Note: We will reset DIS_TERM_DRV to 0 in the 'Set SCSI_CFG1 691 * Microcode Default Value' section below. 692 */ 693 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_SCSI_CFG1, 694 ADW_READ_WORD_REGISTER(iot, ioh, IOPW_SCSI_CFG1) 695 | ADW_DIS_TERM_DRV); 696 697 /* 698 * If the BIOS control flag AIPP (Asynchronous Information 699 * Phase Protection) disable bit is not set, then set the 700 * firmware 'control_flag' CONTROL_FLAG_ENABLE_AIPP bit to 701 * enable AIPP checking and encoding. 702 */ 703 if ((sc->bios_ctrl & BIOS_CTRL_AIPP_DIS) == 0) { 704 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_CONTROL_FLAG, word); 705 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_CONTROL_FLAG, 706 word | CONTROL_FLAG_ENABLE_AIPP); 707 } 708 709 /* 710 * For ASC-38C1600 use DMA_CFG0 default values: 711 * FIFO_THRESH_80B [6:4], and START_CTL_TH [3:2]. 712 */ 713 ADW_WRITE_BYTE_REGISTER(iot, ioh, IOPB_DMA_CFG0, 714 FIFO_THRESH_80B | START_CTL_TH | READ_CMD_MRM); 715 break; 716 } 717 718 /* 719 * Microcode operating variables for WDTR, SDTR, and command tag 720 * queuing will be set in AdvInquiryHandling() based on what a 721 * device reports it is capable of in Inquiry byte 7. 722 * 723 * If SCSI Bus Resets have been disabled, then directly set 724 * SDTR and WDTR from the EEPROM configuration. This will allow 725 * the BIOS and warm boot to work without a SCSI bus hang on 726 * the Inquiry caused by host and target mismatched DTR values. 727 * Without the SCSI Bus Reset, before an Inquiry a device can't 728 * be assumed to be in Asynchronous, Narrow mode. 729 */ 730 if ((sc->bios_ctrl & BIOS_CTRL_RESET_SCSI_BUS) == 0) { 731 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_WDTR_ABLE, sc->wdtr_able); 732 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_SDTR_ABLE, sc->sdtr_able); 733 } 734 735 /* 736 * Set microcode operating variables for SDTR_SPEED1, SDTR_SPEED2, 737 * SDTR_SPEED3, and SDTR_SPEED4 based on the ULTRA EEPROM per TID 738 * bitmask. These values determine the maximum SDTR speed negotiated 739 * with a device. 740 * 741 * The SDTR per TID bitmask overrides the SDTR_SPEED1, SDTR_SPEED2, 742 * SDTR_SPEED3, and SDTR_SPEED4 values so it is safe to set them 743 * without determining here whether the device supports SDTR. 744 */ 745 switch (sc->chip_type) { 746 case ADW_CHIP_ASC3550: 747 word = 0; 748 for (tid = 0; tid <= ADW_MAX_TID; tid++) { 749 if (ADW_TID_TO_TIDMASK(tid) & sc->ultra_able) { 750 /* Set Ultra speed for TID 'tid'. */ 751 word |= (0x3 << (4 * (tid % 4))); 752 } else { 753 /* Set Fast speed for TID 'tid'. */ 754 word |= (0x2 << (4 * (tid % 4))); 755 } 756 /* Check if done with sdtr_speed1. */ 757 if (tid == 3) { 758 ADW_WRITE_WORD_LRAM(iot, ioh, 759 ADW_MC_SDTR_SPEED1, word); 760 word = 0; 761 /* Check if done with sdtr_speed2. */ 762 } else if (tid == 7) { 763 ADW_WRITE_WORD_LRAM(iot, ioh, 764 ADW_MC_SDTR_SPEED2, word); 765 word = 0; 766 /* Check if done with sdtr_speed3. */ 767 } else if (tid == 11) { 768 ADW_WRITE_WORD_LRAM(iot, ioh, 769 ADW_MC_SDTR_SPEED3, word); 770 word = 0; 771 /* Check if done with sdtr_speed4. */ 772 } else if (tid == 15) { 773 ADW_WRITE_WORD_LRAM(iot, ioh, 774 ADW_MC_SDTR_SPEED4, word); 775 /* End of loop. */ 776 } 777 } 778 779 /* 780 * Set microcode operating variable for the 781 * disconnect per TID bitmask. 782 */ 783 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_DISC_ENABLE, 784 sc->cfg.disc_enable); 785 break; 786 787 case ADW_CHIP_ASC38C0800: 788 /* FALLTHROUGH */ 789 case ADW_CHIP_ASC38C1600: 790 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_DISC_ENABLE, 791 sc->cfg.disc_enable); 792 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_SDTR_SPEED1, 793 sc->sdtr_speed1); 794 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_SDTR_SPEED2, 795 sc->sdtr_speed2); 796 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_SDTR_SPEED3, 797 sc->sdtr_speed3); 798 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_SDTR_SPEED4, 799 sc->sdtr_speed4); 800 break; 801 } 802 803 804 /* 805 * Set SCSI_CFG0 Microcode Default Value. 806 * 807 * The microcode will set the SCSI_CFG0 register using this value 808 * after it is started below. 809 */ 810 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_DEFAULT_SCSI_CFG0, 811 ADW_PARITY_EN | ADW_QUEUE_128 | ADW_SEL_TMO_LONG | 812 ADW_OUR_ID_EN | sc->chip_scsi_id); 813 814 815 switch(sc->chip_type) { 816 case ADW_CHIP_ASC3550: 817 error_code = AdwASC3550Cabling(iot, ioh, &sc->cfg); 818 break; 819 820 case ADW_CHIP_ASC38C0800: 821 error_code = AdwASC38C0800Cabling(iot, ioh, &sc->cfg); 822 break; 823 824 case ADW_CHIP_ASC38C1600: 825 error_code = AdwASC38C1600Cabling(iot, ioh, &sc->cfg); 826 break; 827 } 828 if(error_code) { 829 return error_code; 830 } 831 832 /* 833 * Set SEL_MASK Microcode Default Value 834 * 835 * The microcode will set the SEL_MASK register using this value 836 * after it is started below. 837 */ 838 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_DEFAULT_SEL_MASK, 839 ADW_TID_TO_TIDMASK(sc->chip_scsi_id)); 840 841 /* 842 * Create and Initialize Host->RISC Carrier lists 843 */ 844 sc->carr_freelist = AdwInitCarriers(sc->sc_dmamap_carrier, 845 sc->sc_control->carriers); 846 847 /* 848 * Set-up the Host->RISC Initiator Command Queue (ICQ). 849 */ 850 851 if ((sc->icq_sp = sc->carr_freelist) == NULL) { 852 return ADW_IERR_NO_CARRIER; 853 } 854 sc->carr_freelist = ADW_CARRIER_VADDR(sc, 855 ASC_GET_CARRP(sc->icq_sp->next_ba)); 856 857 /* 858 * The first command issued will be placed in the stopper carrier. 859 */ 860 sc->icq_sp->next_ba = htole32(ASC_CQ_STOPPER); 861 862 /* 863 * Set RISC ICQ physical address start value. 864 */ 865 ADW_WRITE_DWORD_LRAM(iot, ioh, ADW_MC_ICQ, le32toh(sc->icq_sp->carr_ba)); 866 867 /* 868 * Initialize the COMMA register to the same value otherwise 869 * the RISC will prematurely detect a command is available. 870 */ 871 if(sc->chip_type == ADW_CHIP_ASC38C1600) { 872 ADW_WRITE_DWORD_REGISTER(iot, ioh, IOPDW_COMMA, 873 le32toh(sc->icq_sp->carr_ba)); 874 } 875 876 /* 877 * Set-up the RISC->Host Initiator Response Queue (IRQ). 878 */ 879 if ((sc->irq_sp = sc->carr_freelist) == NULL) { 880 return ADW_IERR_NO_CARRIER; 881 } 882 sc->carr_freelist = ADW_CARRIER_VADDR(sc, 883 ASC_GET_CARRP(sc->irq_sp->next_ba)); 884 885 /* 886 * The first command completed by the RISC will be placed in 887 * the stopper. 888 * 889 * Note: Set 'next_ba' to ASC_CQ_STOPPER. When the request is 890 * completed the RISC will set the ASC_RQ_DONE bit. 891 */ 892 sc->irq_sp->next_ba = htole32(ASC_CQ_STOPPER); 893 894 /* 895 * Set RISC IRQ physical address start value. 896 */ 897 ADW_WRITE_DWORD_LRAM(iot, ioh, ADW_MC_IRQ, le32toh(sc->irq_sp->carr_ba)); 898 sc->carr_pending_cnt = 0; 899 900 ADW_WRITE_BYTE_REGISTER(iot, ioh, IOPB_INTR_ENABLES, 901 (ADW_INTR_ENABLE_HOST_INTR | ADW_INTR_ENABLE_GLOBAL_INTR)); 902 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_CODE_BEGIN_ADDR, word); 903 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_PC, word); 904 905 /* finally, finally, gentlemen, start your engine */ 906 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_RISC_CSR, ADW_RISC_CSR_RUN); 907 908 /* 909 * Reset the SCSI Bus if the EEPROM indicates that SCSI Bus 910 * Resets should be performed. The RISC has to be running 911 * to issue a SCSI Bus Reset. 912 */ 913 if (sc->bios_ctrl & BIOS_CTRL_RESET_SCSI_BUS) 914 { 915 /* 916 * If the BIOS Signature is present in memory, restore the 917 * BIOS Handshake Configuration Table and do not perform 918 * a SCSI Bus Reset. 919 */ 920 if (bios_mem[(ADW_MC_BIOS_SIGNATURE - ADW_MC_BIOSMEM)/2] == 921 0x55AA) { 922 /* 923 * Restore per TID negotiated values. 924 */ 925 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_WDTR_ABLE, 926 wdtr_able); 927 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_SDTR_ABLE, 928 sdtr_able); 929 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_TAGQNG_ABLE, 930 tagqng_able); 931 for (tid = 0; tid <= ADW_MAX_TID; tid++) { 932 ADW_WRITE_BYTE_LRAM(iot, ioh, 933 ADW_MC_NUMBER_OF_MAX_CMD + tid, 934 max_cmd[tid]); 935 } 936 } else { 937 if (AdwResetCCB(sc) != ADW_TRUE) { 938 error_code = ADW_WARN_BUSRESET_ERROR; 939 } 940 } 941 } 942 943 return error_code; 944 } 945 946 947 int 948 AdwRamSelfTest(bus_space_tag_t iot, bus_space_handle_t ioh, u_int8_t chip_type) 949 { 950 int i; 951 u_int8_t byte; 952 953 954 if ((chip_type == ADW_CHIP_ASC38C0800) || 955 (chip_type == ADW_CHIP_ASC38C1600)) { 956 /* 957 * RAM BIST (RAM Built-In Self Test) 958 * 959 * Address : I/O base + offset 0x38h register (byte). 960 * Function: Bit 7-6(RW) : RAM mode 961 * Normal Mode : 0x00 962 * Pre-test Mode : 0x40 963 * RAM Test Mode : 0x80 964 * Bit 5 : unused 965 * Bit 4(RO) : Done bit 966 * Bit 3-0(RO) : Status 967 * Host Error : 0x08 968 * Int_RAM Error : 0x04 969 * RISC Error : 0x02 970 * SCSI Error : 0x01 971 * No Error : 0x00 972 * 973 * Note: RAM BIST code should be put right here, before loading 974 * the microcode and after saving the RISC memory BIOS region. 975 */ 976 977 /* 978 * LRAM Pre-test 979 * 980 * Write PRE_TEST_MODE (0x40) to register and wait for 981 * 10 milliseconds. 982 * If Done bit not set or low nibble not PRE_TEST_VALUE (0x05), 983 * return an error. Reset to NORMAL_MODE (0x00) and do again. 984 * If cannot reset to NORMAL_MODE, return an error too. 985 */ 986 for (i = 0; i < 2; i++) { 987 ADW_WRITE_BYTE_REGISTER(iot, ioh, IOPB_RAM_BIST, 988 PRE_TEST_MODE); 989 /* Wait for 10ms before reading back. */ 990 AdwSleepMilliSecond(10); 991 byte = ADW_READ_BYTE_REGISTER(iot, ioh, IOPB_RAM_BIST); 992 if ((byte & RAM_TEST_DONE) == 0 || (byte & 0x0F) != 993 PRE_TEST_VALUE) { 994 return ADW_IERR_BIST_PRE_TEST; 995 } 996 997 ADW_WRITE_BYTE_REGISTER(iot, ioh, IOPB_RAM_BIST, 998 NORMAL_MODE); 999 /* Wait for 10ms before reading back. */ 1000 AdwSleepMilliSecond(10); 1001 if (ADW_READ_BYTE_REGISTER(iot, ioh, IOPB_RAM_BIST) 1002 != NORMAL_VALUE) { 1003 return ADW_IERR_BIST_PRE_TEST; 1004 } 1005 } 1006 1007 /* 1008 * LRAM Test - It takes about 1.5 ms to run through the test. 1009 * 1010 * Write RAM_TEST_MODE (0x80) to register and wait for 1011 * 10 milliseconds. 1012 * If Done bit not set or Status not 0, save register byte, 1013 * set the err_code, and return an error. 1014 */ 1015 ADW_WRITE_BYTE_REGISTER(iot, ioh, IOPB_RAM_BIST, RAM_TEST_MODE); 1016 /* Wait for 10ms before checking status. */ 1017 AdwSleepMilliSecond(10); 1018 1019 byte = ADW_READ_BYTE_REGISTER(iot, ioh, IOPB_RAM_BIST); 1020 if ((byte & RAM_TEST_DONE)==0 || (byte & RAM_TEST_STATUS)!=0) { 1021 /* Get here if Done bit not set or Status not 0. */ 1022 return ADW_IERR_BIST_RAM_TEST; 1023 } 1024 1025 /* We need to reset back to normal mode after LRAM test passes*/ 1026 ADW_WRITE_BYTE_REGISTER(iot, ioh, IOPB_RAM_BIST, NORMAL_MODE); 1027 } 1028 1029 return 0; 1030 } 1031 1032 1033 int 1034 AdwLoadMCode(bus_space_tag_t iot, bus_space_handle_t ioh, u_int16_t *bios_mem, u_int8_t chip_type) 1035 { 1036 const u_int8_t *mcode_data; 1037 u_int32_t mcode_chksum; 1038 u_int16_t mcode_size; 1039 u_int32_t sum; 1040 u_int16_t code_sum; 1041 int begin_addr; 1042 int end_addr; 1043 int word; 1044 int adw_memsize; 1045 int adw_mcode_expanded_size; 1046 int i, j; 1047 1048 1049 switch(chip_type) { 1050 case ADW_CHIP_ASC3550: 1051 mcode_data = (const u_int8_t *)adw_asc3550_mcode_data.mcode_data; 1052 mcode_chksum = (u_int32_t)adw_asc3550_mcode_data.mcode_chksum; 1053 mcode_size = (u_int16_t)adw_asc3550_mcode_data.mcode_size; 1054 adw_memsize = ADW_3550_MEMSIZE; 1055 break; 1056 1057 case ADW_CHIP_ASC38C0800: 1058 mcode_data = (const u_int8_t *)adw_asc38C0800_mcode_data.mcode_data; 1059 mcode_chksum =(u_int32_t)adw_asc38C0800_mcode_data.mcode_chksum; 1060 mcode_size = (u_int16_t)adw_asc38C0800_mcode_data.mcode_size; 1061 adw_memsize = ADW_38C0800_MEMSIZE; 1062 break; 1063 1064 case ADW_CHIP_ASC38C1600: 1065 mcode_data = (const u_int8_t *)adw_asc38C1600_mcode_data.mcode_data; 1066 mcode_chksum =(u_int32_t)adw_asc38C1600_mcode_data.mcode_chksum; 1067 mcode_size = (u_int16_t)adw_asc38C1600_mcode_data.mcode_size; 1068 adw_memsize = ADW_38C1600_MEMSIZE; 1069 break; 1070 1071 default: 1072 return (EINVAL); 1073 } 1074 1075 /* 1076 * Write the microcode image to RISC memory starting at address 0. 1077 */ 1078 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_RAM_ADDR, 0); 1079 1080 /* Assume the following compressed format of the microcode buffer: 1081 * 1082 * 254 word (508 byte) table indexed by byte code followed 1083 * by the following byte codes: 1084 * 1085 * 1-Byte Code: 1086 * 00: Emit word 0 in table. 1087 * 01: Emit word 1 in table. 1088 * . 1089 * FD: Emit word 253 in table. 1090 * 1091 * Multi-Byte Code: 1092 * FE WW WW: (3 byte code) Word to emit is the next word WW WW. 1093 * FF BB WW WW: (4 byte code) Emit BB count times next word WW WW. 1094 */ 1095 word = 0; 1096 for (i = 253 * 2; i < mcode_size; i++) { 1097 if (mcode_data[i] == 0xff) { 1098 for (j = 0; j < mcode_data[i + 1]; j++) { 1099 ADW_WRITE_WORD_AUTO_INC_LRAM(iot, ioh, 1100 (((u_int16_t)mcode_data[i + 3] << 8) | 1101 mcode_data[i + 2])); 1102 word++; 1103 } 1104 i += 3; 1105 } else if (mcode_data[i] == 0xfe) { 1106 ADW_WRITE_WORD_AUTO_INC_LRAM(iot, ioh, 1107 (((u_int16_t)mcode_data[i + 2] << 8) | 1108 mcode_data[i + 1])); 1109 i += 2; 1110 word++; 1111 } else { 1112 ADW_WRITE_WORD_AUTO_INC_LRAM(iot, ioh, (((u_int16_t) 1113 mcode_data[(mcode_data[i] * 2) + 1] <<8) | 1114 mcode_data[mcode_data[i] * 2])); 1115 word++; 1116 } 1117 } 1118 1119 /* 1120 * Set 'word' for later use to clear the rest of memory and save 1121 * the expanded mcode size. 1122 */ 1123 word *= 2; 1124 adw_mcode_expanded_size = word; 1125 1126 /* 1127 * Clear the rest of the Internal RAM. 1128 */ 1129 for (; word < adw_memsize; word += 2) { 1130 ADW_WRITE_WORD_AUTO_INC_LRAM(iot, ioh, 0); 1131 } 1132 1133 /* 1134 * Verify the microcode checksum. 1135 */ 1136 sum = 0; 1137 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_RAM_ADDR, 0); 1138 1139 for (word = 0; word < adw_mcode_expanded_size; word += 2) { 1140 sum += ADW_READ_WORD_AUTO_INC_LRAM(iot, ioh); 1141 } 1142 1143 if (sum != mcode_chksum) { 1144 return ADW_IERR_MCODE_CHKSUM; 1145 } 1146 1147 /* 1148 * Restore the RISC memory BIOS region. 1149 */ 1150 for (i = 0; i < ADW_MC_BIOSLEN/2; i++) { 1151 if(chip_type == ADW_CHIP_ASC3550) { 1152 ADW_WRITE_BYTE_LRAM(iot, ioh, ADW_MC_BIOSMEM + (2 * i), 1153 bios_mem[i]); 1154 } else { 1155 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_BIOSMEM + (2 * i), 1156 bios_mem[i]); 1157 } 1158 } 1159 1160 /* 1161 * Calculate and write the microcode code checksum to the microcode 1162 * code checksum location ADW_MC_CODE_CHK_SUM (0x2C). 1163 */ 1164 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_CODE_BEGIN_ADDR, begin_addr); 1165 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_CODE_END_ADDR, end_addr); 1166 code_sum = 0; 1167 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_RAM_ADDR, begin_addr); 1168 for (word = begin_addr; word < end_addr; word += 2) { 1169 code_sum += ADW_READ_WORD_AUTO_INC_LRAM(iot, ioh); 1170 } 1171 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_CODE_CHK_SUM, code_sum); 1172 1173 /* 1174 * Set the chip type. 1175 */ 1176 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_CHIP_TYPE, chip_type); 1177 1178 return 0; 1179 } 1180 1181 1182 int 1183 AdwASC3550Cabling(bus_space_tag_t iot, bus_space_handle_t ioh, ADW_DVC_CFG *cfg) 1184 { 1185 u_int16_t scsi_cfg1; 1186 1187 1188 /* 1189 * Determine SCSI_CFG1 Microcode Default Value. 1190 * 1191 * The microcode will set the SCSI_CFG1 register using this value 1192 * after it is started below. 1193 */ 1194 1195 /* Read current SCSI_CFG1 Register value. */ 1196 scsi_cfg1 = ADW_READ_WORD_REGISTER(iot, ioh, IOPW_SCSI_CFG1); 1197 1198 /* 1199 * If all three connectors are in use in ASC3550, return an error. 1200 */ 1201 if ((scsi_cfg1 & CABLE_ILLEGAL_A) == 0 || 1202 (scsi_cfg1 & CABLE_ILLEGAL_B) == 0) { 1203 return ADW_IERR_ILLEGAL_CONNECTION; 1204 } 1205 1206 /* 1207 * If the cable is reversed all of the SCSI_CTRL register signals 1208 * will be set. Check for and return an error if this condition is 1209 * found. 1210 */ 1211 if ((ADW_READ_WORD_REGISTER(iot,ioh, IOPW_SCSI_CTRL) & 0x3F07)==0x3F07){ 1212 return ADW_IERR_REVERSED_CABLE; 1213 } 1214 1215 /* 1216 * If this is a differential board and a single-ended device 1217 * is attached to one of the connectors, return an error. 1218 */ 1219 if ((scsi_cfg1 & ADW_DIFF_MODE) && 1220 (scsi_cfg1 & ADW_DIFF_SENSE) == 0) { 1221 return ADW_IERR_SINGLE_END_DEVICE; 1222 } 1223 1224 /* 1225 * If automatic termination control is enabled, then set the 1226 * termination value based on a table listed in a_condor.h. 1227 * 1228 * If manual termination was specified with an EEPROM setting 1229 * then 'termination' was set-up in AdwInitFromEEPROM() and 1230 * is ready to be 'ored' into SCSI_CFG1. 1231 */ 1232 if (cfg->termination == 0) { 1233 /* 1234 * The software always controls termination by setting 1235 * TERM_CTL_SEL. 1236 * If TERM_CTL_SEL were set to 0, the hardware would set 1237 * termination. 1238 */ 1239 cfg->termination |= ADW_TERM_CTL_SEL; 1240 1241 switch(scsi_cfg1 & ADW_CABLE_DETECT) { 1242 /* TERM_CTL_H: on, TERM_CTL_L: on */ 1243 case 0x3: case 0x7: case 0xB: 1244 case 0xD: case 0xE: case 0xF: 1245 cfg->termination |= 1246 (ADW_TERM_CTL_H | ADW_TERM_CTL_L); 1247 break; 1248 1249 /* TERM_CTL_H: on, TERM_CTL_L: off */ 1250 case 0x1: case 0x5: case 0x9: 1251 case 0xA: case 0xC: 1252 cfg->termination |= ADW_TERM_CTL_H; 1253 break; 1254 1255 /* TERM_CTL_H: off, TERM_CTL_L: off */ 1256 case 0x2: case 0x6: 1257 break; 1258 } 1259 } 1260 1261 /* 1262 * Clear any set TERM_CTL_H and TERM_CTL_L bits. 1263 */ 1264 scsi_cfg1 &= ~ADW_TERM_CTL; 1265 1266 /* 1267 * Invert the TERM_CTL_H and TERM_CTL_L bits and then 1268 * set 'scsi_cfg1'. The TERM_POL bit does not need to be 1269 * referenced, because the hardware internally inverts 1270 * the Termination High and Low bits if TERM_POL is set. 1271 */ 1272 scsi_cfg1 |= (ADW_TERM_CTL_SEL | (~cfg->termination & ADW_TERM_CTL)); 1273 1274 /* 1275 * Set SCSI_CFG1 Microcode Default Value 1276 * 1277 * Set filter value and possibly modified termination control 1278 * bits in the Microcode SCSI_CFG1 Register Value. 1279 * 1280 * The microcode will set the SCSI_CFG1 register using this value 1281 * after it is started below. 1282 */ 1283 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_DEFAULT_SCSI_CFG1, 1284 ADW_FLTR_DISABLE | scsi_cfg1); 1285 1286 /* 1287 * Set MEM_CFG Microcode Default Value 1288 * 1289 * The microcode will set the MEM_CFG register using this value 1290 * after it is started below. 1291 * 1292 * MEM_CFG may be accessed as a word or byte, but only bits 0-7 1293 * are defined. 1294 * 1295 * ASC-3550 has 8KB internal memory. 1296 */ 1297 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_DEFAULT_MEM_CFG, 1298 ADW_BIOS_EN | ADW_RAM_SZ_8KB); 1299 1300 return 0; 1301 } 1302 1303 1304 int 1305 AdwASC38C0800Cabling(bus_space_tag_t iot, bus_space_handle_t ioh, ADW_DVC_CFG *cfg) 1306 { 1307 u_int16_t scsi_cfg1; 1308 1309 1310 /* 1311 * Determine SCSI_CFG1 Microcode Default Value. 1312 * 1313 * The microcode will set the SCSI_CFG1 register using this value 1314 * after it is started below. 1315 */ 1316 1317 /* Read current SCSI_CFG1 Register value. */ 1318 scsi_cfg1 = ADW_READ_WORD_REGISTER(iot, ioh, IOPW_SCSI_CFG1); 1319 1320 /* 1321 * If the cable is reversed all of the SCSI_CTRL register signals 1322 * will be set. Check for and return an error if this condition is 1323 * found. 1324 */ 1325 if ((ADW_READ_WORD_REGISTER(iot,ioh, IOPW_SCSI_CTRL) & 0x3F07)==0x3F07){ 1326 return ADW_IERR_REVERSED_CABLE; 1327 } 1328 1329 /* 1330 * All kind of combinations of devices attached to one of four 1331 * connectors are acceptable except HVD device attached. 1332 * For example, LVD device can be attached to SE connector while 1333 * SE device attached to LVD connector. 1334 * If LVD device attached to SE connector, it only runs up to 1335 * Ultra speed. 1336 * 1337 * If an HVD device is attached to one of LVD connectors, return 1338 * an error. 1339 * However, there is no way to detect HVD device attached to 1340 * SE connectors. 1341 */ 1342 if (scsi_cfg1 & ADW_HVD) { 1343 return ADW_IERR_HVD_DEVICE; 1344 } 1345 1346 /* 1347 * If either SE or LVD automatic termination control is enabled, then 1348 * set the termination value based on a table listed in a_condor.h. 1349 * 1350 * If manual termination was specified with an EEPROM setting then 1351 * 'termination' was set-up in AdwInitFromEEPROM() and is ready 1352 * to be 'ored' into SCSI_CFG1. 1353 */ 1354 if ((cfg->termination & ADW_TERM_SE) == 0) { 1355 /* SE automatic termination control is enabled. */ 1356 switch(scsi_cfg1 & ADW_C_DET_SE) { 1357 /* TERM_SE_HI: on, TERM_SE_LO: on */ 1358 case 0x1: case 0x2: case 0x3: 1359 cfg->termination |= ADW_TERM_SE; 1360 break; 1361 1362 /* TERM_SE_HI: on, TERM_SE_LO: off */ 1363 case 0x0: 1364 cfg->termination |= ADW_TERM_SE_HI; 1365 break; 1366 } 1367 } 1368 1369 if ((cfg->termination & ADW_TERM_LVD) == 0) { 1370 /* LVD automatic termination control is enabled. */ 1371 switch(scsi_cfg1 & ADW_C_DET_LVD) { 1372 /* TERM_LVD_HI: on, TERM_LVD_LO: on */ 1373 case 0x4: case 0x8: case 0xC: 1374 cfg->termination |= ADW_TERM_LVD; 1375 break; 1376 1377 /* TERM_LVD_HI: off, TERM_LVD_LO: off */ 1378 case 0x0: 1379 break; 1380 } 1381 } 1382 1383 /* 1384 * Clear any set TERM_SE and TERM_LVD bits. 1385 */ 1386 scsi_cfg1 &= (~ADW_TERM_SE & ~ADW_TERM_LVD); 1387 1388 /* 1389 * Invert the TERM_SE and TERM_LVD bits and then set 'scsi_cfg1'. 1390 */ 1391 scsi_cfg1 |= (~cfg->termination & 0xF0); 1392 1393 /* 1394 * Clear BIG_ENDIAN, DIS_TERM_DRV, Terminator Polarity and 1395 * HVD/LVD/SE bits and set possibly modified termination control bits 1396 * in the Microcode SCSI_CFG1 Register Value. 1397 */ 1398 scsi_cfg1 &= (~ADW_BIG_ENDIAN & ~ADW_DIS_TERM_DRV & 1399 ~ADW_TERM_POL & ~ADW_HVD_LVD_SE); 1400 1401 /* 1402 * Set SCSI_CFG1 Microcode Default Value 1403 * 1404 * Set possibly modified termination control and reset DIS_TERM_DRV 1405 * bits in the Microcode SCSI_CFG1 Register Value. 1406 * 1407 * The microcode will set the SCSI_CFG1 register using this value 1408 * after it is started below. 1409 */ 1410 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_DEFAULT_SCSI_CFG1, scsi_cfg1); 1411 1412 /* 1413 * Set MEM_CFG Microcode Default Value 1414 * 1415 * The microcode will set the MEM_CFG register using this value 1416 * after it is started below. 1417 * 1418 * MEM_CFG may be accessed as a word or byte, but only bits 0-7 1419 * are defined. 1420 * 1421 * ASC-38C0800 has 16KB internal memory. 1422 */ 1423 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_DEFAULT_MEM_CFG, 1424 ADW_BIOS_EN | ADW_RAM_SZ_16KB); 1425 1426 return 0; 1427 } 1428 1429 1430 int 1431 AdwASC38C1600Cabling(bus_space_tag_t iot, bus_space_handle_t ioh, ADW_DVC_CFG *cfg) 1432 { 1433 u_int16_t scsi_cfg1; 1434 1435 1436 /* 1437 * Determine SCSI_CFG1 Microcode Default Value. 1438 * 1439 * The microcode will set the SCSI_CFG1 register using this value 1440 * after it is started below. 1441 * Each ASC-38C1600 function has only two cable detect bits. 1442 * The bus mode override bits are in IOPB_SOFT_OVER_WR. 1443 */ 1444 1445 /* Read current SCSI_CFG1 Register value. */ 1446 scsi_cfg1 = ADW_READ_WORD_REGISTER(iot, ioh, IOPW_SCSI_CFG1); 1447 1448 /* 1449 * If the cable is reversed all of the SCSI_CTRL register signals 1450 * will be set. Check for and return an error if this condition is 1451 * found. 1452 */ 1453 if ((ADW_READ_WORD_REGISTER(iot,ioh, IOPW_SCSI_CTRL) & 0x3F07)==0x3F07){ 1454 return ADW_IERR_REVERSED_CABLE; 1455 } 1456 1457 /* 1458 * Each ASC-38C1600 function has two connectors. Only an HVD device 1459 * cannot be connected to either connector. An LVD device or SE device 1460 * may be connected to either connector. If an SE device is connected, 1461 * then at most Ultra speed (20 MHz) can be used on both connectors. 1462 * 1463 * If an HVD device is attached, return an error. 1464 */ 1465 if (scsi_cfg1 & ADW_HVD) { 1466 return ADW_IERR_HVD_DEVICE; 1467 } 1468 1469 /* 1470 * Each function in the ASC-38C1600 uses only the SE cable detect and 1471 * termination because there are two connectors for each function. 1472 * Each function may use either LVD or SE mode. 1473 * Corresponding the SE automatic termination control EEPROM bits are 1474 * used for each function. 1475 * Each function has its own EEPROM. If SE automatic control is enabled 1476 * for the function, then set the termination value based on a table 1477 * listed in adwlib.h. 1478 * 1479 * If manual termination is specified in the EEPROM for the function, 1480 * then 'termination' was set-up in AdwInitFromEEPROM() and is 1481 * ready to be 'ored' into SCSI_CFG1. 1482 */ 1483 if ((cfg->termination & ADW_TERM_SE) == 0) { 1484 /* SE automatic termination control is enabled. */ 1485 switch(scsi_cfg1 & ADW_C_DET_SE) { 1486 /* TERM_SE_HI: on, TERM_SE_LO: on */ 1487 case 0x1: case 0x2: case 0x3: 1488 cfg->termination |= ADW_TERM_SE; 1489 break; 1490 1491 case 0x0: 1492 #if 0 1493 /* !!!!TODO!!!! */ 1494 if (ASC_PCI_ID2FUNC(cfg->pci_slot_info) == 0) { 1495 /* Function 0 - TERM_SE_HI: off, TERM_SE_LO: off */ 1496 } 1497 else 1498 #endif 1499 { 1500 /* Function 1 - TERM_SE_HI: on, TERM_SE_LO: off */ 1501 cfg->termination |= ADW_TERM_SE_HI; 1502 } 1503 break; 1504 } 1505 } 1506 1507 /* 1508 * Clear any set TERM_SE bits. 1509 */ 1510 scsi_cfg1 &= ~ADW_TERM_SE; 1511 1512 /* 1513 * Invert the TERM_SE bits and then set 'scsi_cfg1'. 1514 */ 1515 scsi_cfg1 |= (~cfg->termination & ADW_TERM_SE); 1516 1517 /* 1518 * Clear Big Endian and Terminator Polarity bits and set possibly 1519 * modified termination control bits in the Microcode SCSI_CFG1 1520 * Register Value. 1521 */ 1522 scsi_cfg1 &= (~ADW_BIG_ENDIAN & ~ADW_DIS_TERM_DRV & ~ADW_TERM_POL); 1523 1524 /* 1525 * Set SCSI_CFG1 Microcode Default Value 1526 * 1527 * Set possibly modified termination control bits in the Microcode 1528 * SCSI_CFG1 Register Value. 1529 * 1530 * The microcode will set the SCSI_CFG1 register using this value 1531 * after it is started below. 1532 */ 1533 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_DEFAULT_SCSI_CFG1, scsi_cfg1); 1534 1535 /* 1536 * Set MEM_CFG Microcode Default Value 1537 * 1538 * The microcode will set the MEM_CFG register using this value 1539 * after it is started below. 1540 * 1541 * MEM_CFG may be accessed as a word or byte, but only bits 0-7 1542 * are defined. 1543 * 1544 * ASC-38C1600 has 32KB internal memory. 1545 */ 1546 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_DEFAULT_MEM_CFG, 1547 ADW_BIOS_EN | ADW_RAM_SZ_32KB); 1548 1549 return 0; 1550 } 1551 1552 1553 /* 1554 * Read EEPROM configuration into the specified buffer. 1555 * 1556 * Return a checksum based on the EEPROM configuration read. 1557 */ 1558 static u_int16_t 1559 AdwGetEEPROMConfig(bus_space_tag_t iot, bus_space_handle_t ioh, ADW_EEPROM *cfg_buf) 1560 { 1561 u_int16_t wval, chksum; 1562 u_int16_t *wbuf; 1563 int eep_addr; 1564 1565 1566 wbuf = (u_int16_t *) cfg_buf; 1567 chksum = 0; 1568 1569 for (eep_addr = ASC_EEP_DVC_CFG_BEGIN; 1570 eep_addr < ASC_EEP_DVC_CFG_END; 1571 eep_addr++, wbuf++) { 1572 wval = AdwReadEEPWord(iot, ioh, eep_addr); 1573 chksum += wval; 1574 *wbuf = wval; 1575 } 1576 1577 *wbuf = AdwReadEEPWord(iot, ioh, eep_addr); 1578 wbuf++; 1579 for (eep_addr = ASC_EEP_DVC_CTL_BEGIN; 1580 eep_addr < ASC_EEP_MAX_WORD_ADDR; 1581 eep_addr++, wbuf++) { 1582 *wbuf = AdwReadEEPWord(iot, ioh, eep_addr); 1583 } 1584 1585 return chksum; 1586 } 1587 1588 1589 /* 1590 * Read the EEPROM from specified location 1591 */ 1592 static u_int16_t 1593 AdwReadEEPWord(bus_space_tag_t iot, bus_space_handle_t ioh, int eep_word_addr) 1594 { 1595 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_EE_CMD, 1596 ASC_EEP_CMD_READ | eep_word_addr); 1597 AdwWaitEEPCmd(iot, ioh); 1598 1599 return ADW_READ_WORD_REGISTER(iot, ioh, IOPW_EE_DATA); 1600 } 1601 1602 1603 /* 1604 * Wait for EEPROM command to complete 1605 */ 1606 static void 1607 AdwWaitEEPCmd(bus_space_tag_t iot, bus_space_handle_t ioh) 1608 { 1609 int eep_delay_ms; 1610 1611 1612 for (eep_delay_ms = 0; eep_delay_ms < ASC_EEP_DELAY_MS; eep_delay_ms++){ 1613 if (ADW_READ_WORD_REGISTER(iot, ioh, IOPW_EE_CMD) & 1614 ASC_EEP_CMD_DONE) { 1615 break; 1616 } 1617 AdwSleepMilliSecond(1); 1618 } 1619 1620 (void)ADW_READ_WORD_REGISTER(iot, ioh, IOPW_EE_CMD); 1621 } 1622 1623 1624 /* 1625 * Write the EEPROM from 'cfg_buf'. 1626 */ 1627 static void 1628 AdwSetEEPROMConfig(bus_space_tag_t iot, bus_space_handle_t ioh, ADW_EEPROM *cfg_buf) 1629 { 1630 u_int16_t *wbuf; 1631 u_int16_t addr, chksum; 1632 1633 1634 wbuf = (u_int16_t *) cfg_buf; 1635 chksum = 0; 1636 1637 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_EE_CMD, ASC_EEP_CMD_WRITE_ABLE); 1638 AdwWaitEEPCmd(iot, ioh); 1639 1640 /* 1641 * Write EEPROM from word 0 to word 20 1642 */ 1643 for (addr = ASC_EEP_DVC_CFG_BEGIN; 1644 addr < ASC_EEP_DVC_CFG_END; addr++, wbuf++) { 1645 chksum += *wbuf; 1646 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_EE_DATA, *wbuf); 1647 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_EE_CMD, 1648 ASC_EEP_CMD_WRITE | addr); 1649 AdwWaitEEPCmd(iot, ioh); 1650 AdwSleepMilliSecond(ASC_EEP_DELAY_MS); 1651 } 1652 1653 /* 1654 * Write EEPROM checksum at word 21 1655 */ 1656 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_EE_DATA, chksum); 1657 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_EE_CMD, 1658 ASC_EEP_CMD_WRITE | addr); 1659 AdwWaitEEPCmd(iot, ioh); 1660 wbuf++; /* skip over check_sum */ 1661 1662 /* 1663 * Write EEPROM OEM name at words 22 to 29 1664 */ 1665 for (addr = ASC_EEP_DVC_CTL_BEGIN; 1666 addr < ASC_EEP_MAX_WORD_ADDR; addr++, wbuf++) { 1667 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_EE_DATA, *wbuf); 1668 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_EE_CMD, 1669 ASC_EEP_CMD_WRITE | addr); 1670 AdwWaitEEPCmd(iot, ioh); 1671 } 1672 1673 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_EE_CMD, 1674 ASC_EEP_CMD_WRITE_DISABLE); 1675 AdwWaitEEPCmd(iot, ioh); 1676 1677 return; 1678 } 1679 1680 1681 /* 1682 * AdwExeScsiQueue() - Send a request to the RISC microcode program. 1683 * 1684 * Allocate a carrier structure, point the carrier to the ADW_SCSI_REQ_Q, 1685 * add the carrier to the ICQ (Initiator Command Queue), and tickle the 1686 * RISC to notify it a new command is ready to be executed. 1687 * 1688 * If 'done_status' is not set to QD_DO_RETRY, then 'error_retry' will be 1689 * set to SCSI_MAX_RETRY. 1690 * 1691 * Return: 1692 * ADW_SUCCESS(1) - The request was successfully queued. 1693 * ADW_BUSY(0) - Resource unavailable; Retry again after pending 1694 * request completes. 1695 * ADW_ERROR(-1) - Invalid ADW_SCSI_REQ_Q request structure 1696 * host IC error. 1697 */ 1698 int 1699 AdwExeScsiQueue(ADW_SOFTC *sc, ADW_SCSI_REQ_Q *scsiq) 1700 { 1701 bus_space_tag_t iot = sc->sc_iot; 1702 bus_space_handle_t ioh = sc->sc_ioh; 1703 ADW_CCB *ccb; 1704 u_int32_t req_paddr; 1705 ADW_CARRIER *new_carrp; 1706 1707 /* 1708 * The ADW_SCSI_REQ_Q 'target_id' field should never exceed ADW_MAX_TID. 1709 */ 1710 if (scsiq->target_id > ADW_MAX_TID) { 1711 scsiq->host_status = QHSTA_M_INVALID_DEVICE; 1712 scsiq->done_status = QD_WITH_ERROR; 1713 return ADW_ERROR; 1714 } 1715 1716 /* 1717 * Begin of CRITICAL SECTION: Must be protected within splbio/splx pair 1718 */ 1719 1720 ccb = adw_ccb_phys_kv(sc, scsiq->ccb_ptr); 1721 1722 /* 1723 * Allocate a carrier and initialize fields. 1724 */ 1725 if ((new_carrp = sc->carr_freelist) == NULL) { 1726 return ADW_BUSY; 1727 } 1728 sc->carr_freelist = ADW_CARRIER_VADDR(sc, 1729 ASC_GET_CARRP(new_carrp->next_ba)); 1730 sc->carr_pending_cnt++; 1731 1732 /* 1733 * Set the carrier to be a stopper by setting 'next_ba' 1734 * to the stopper value. The current stopper will be changed 1735 * below to point to the new stopper. 1736 */ 1737 new_carrp->next_ba = htole32(ASC_CQ_STOPPER); 1738 1739 req_paddr = sc->sc_dmamap_control->dm_segs[0].ds_addr + 1740 ADW_CCB_OFF(ccb) + offsetof(struct adw_ccb, scsiq); 1741 1742 /* Save physical address of ADW_SCSI_REQ_Q and Carrier. */ 1743 scsiq->scsiq_rptr = htole32(req_paddr); 1744 1745 /* 1746 * Every ADV_CARR_T.carr_ba is byte swapped to little-endian 1747 * order during initialization. 1748 */ 1749 scsiq->carr_ba = sc->icq_sp->carr_ba; 1750 scsiq->carr_va = sc->icq_sp->carr_ba; 1751 1752 /* 1753 * Use the current stopper to send the ADW_SCSI_REQ_Q command to 1754 * the microcode. The newly allocated stopper will become the new 1755 * stopper. 1756 */ 1757 sc->icq_sp->areq_ba = htole32(req_paddr); 1758 1759 /* 1760 * Set the 'next_ba' pointer for the old stopper to be the 1761 * physical address of the new stopper. The RISC can only 1762 * follow physical addresses. 1763 */ 1764 sc->icq_sp->next_ba = new_carrp->carr_ba; 1765 1766 #if ADW_DEBUG 1767 printf("icq 0x%x, 0x%x, 0x%x, 0x%x\n", 1768 sc->icq_sp->carr_id, 1769 sc->icq_sp->carr_ba, 1770 sc->icq_sp->areq_ba, 1771 sc->icq_sp->next_ba); 1772 #endif 1773 /* 1774 * Set the host adapter stopper pointer to point to the new carrier. 1775 */ 1776 sc->icq_sp = new_carrp; 1777 1778 if (sc->chip_type == ADW_CHIP_ASC3550 || 1779 sc->chip_type == ADW_CHIP_ASC38C0800) { 1780 /* 1781 * Tickle the RISC to tell it to read its Command Queue Head 1782 * pointer. 1783 */ 1784 ADW_WRITE_BYTE_REGISTER(iot, ioh, IOPB_TICKLE, ADW_TICKLE_A); 1785 if (sc->chip_type == ADW_CHIP_ASC3550) { 1786 /* 1787 * Clear the tickle value. In the ASC-3550 the RISC flag 1788 * command 'clr_tickle_a' does not work unless the host 1789 * value is cleared. 1790 */ 1791 ADW_WRITE_BYTE_REGISTER(iot, ioh, IOPB_TICKLE, 1792 ADW_TICKLE_NOP); 1793 } 1794 } else if (sc->chip_type == ADW_CHIP_ASC38C1600) { 1795 /* 1796 * Notify the RISC a carrier is ready by writing the physical 1797 * address of the new carrier stopper to the COMMA register. 1798 */ 1799 ADW_WRITE_DWORD_REGISTER(iot, ioh, IOPDW_COMMA, 1800 le32toh(new_carrp->carr_ba)); 1801 } 1802 1803 /* 1804 * End of CRITICAL SECTION: Must be protected within splbio/splx pair 1805 */ 1806 1807 return ADW_SUCCESS; 1808 } 1809 1810 1811 void 1812 AdwResetChip(bus_space_tag_t iot, bus_space_handle_t ioh) 1813 { 1814 1815 /* 1816 * Reset Chip. 1817 */ 1818 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_CTRL_REG, 1819 ADW_CTRL_REG_CMD_RESET); 1820 AdwSleepMilliSecond(100); 1821 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_CTRL_REG, 1822 ADW_CTRL_REG_CMD_WR_IO_REG); 1823 } 1824 1825 1826 /* 1827 * Reset SCSI Bus and purge all outstanding requests. 1828 * 1829 * Return Value: 1830 * ADW_TRUE(1) - All requests are purged and SCSI Bus is reset. 1831 * ADW_FALSE(0) - Microcode command failed. 1832 * ADW_ERROR(-1) - Microcode command timed-out. Microcode or IC 1833 * may be hung which requires driver recovery. 1834 */ 1835 int 1836 AdwResetCCB(ADW_SOFTC *sc) 1837 { 1838 int status; 1839 1840 /* 1841 * Send the SCSI Bus Reset idle start idle command which asserts 1842 * the SCSI Bus Reset signal. 1843 */ 1844 status = AdwSendIdleCmd(sc, (u_int16_t) IDLE_CMD_SCSI_RESET_START, 0L); 1845 if (status != ADW_TRUE) { 1846 return status; 1847 } 1848 1849 /* 1850 * Delay for the specified SCSI Bus Reset hold time. 1851 * 1852 * The hold time delay is done on the host because the RISC has no 1853 * microsecond accurate timer. 1854 */ 1855 AdwDelayMicroSecond((u_int16_t) ASC_SCSI_RESET_HOLD_TIME_US); 1856 1857 /* 1858 * Send the SCSI Bus Reset end idle command which de-asserts 1859 * the SCSI Bus Reset signal and purges any pending requests. 1860 */ 1861 status = AdwSendIdleCmd(sc, (u_int16_t) IDLE_CMD_SCSI_RESET_END, 0L); 1862 if (status != ADW_TRUE) { 1863 return status; 1864 } 1865 1866 AdwSleepMilliSecond((u_int32_t) sc->scsi_reset_wait * 1000); 1867 1868 return status; 1869 } 1870 1871 1872 /* 1873 * Reset chip and SCSI Bus. 1874 * 1875 * Return Value: 1876 * ADW_TRUE(1) - Chip re-initialization and SCSI Bus Reset successful. 1877 * ADW_FALSE(0) - Chip re-initialization and SCSI Bus Reset failure. 1878 */ 1879 int 1880 AdwResetSCSIBus(ADW_SOFTC *sc) 1881 { 1882 bus_space_tag_t iot = sc->sc_iot; 1883 bus_space_handle_t ioh = sc->sc_ioh; 1884 int status; 1885 u_int16_t wdtr_able, sdtr_able, tagqng_able; 1886 u_int16_t ppr_able = 0; /* XXX: gcc */ 1887 u_int8_t tid, max_cmd[ADW_MAX_TID + 1]; 1888 u_int16_t bios_sig; 1889 1890 1891 /* 1892 * Save current per TID negotiated values. 1893 */ 1894 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_WDTR_ABLE, wdtr_able); 1895 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_SDTR_ABLE, sdtr_able); 1896 if (sc->chip_type == ADW_CHIP_ASC38C1600) { 1897 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_PPR_ABLE, ppr_able); 1898 } 1899 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_TAGQNG_ABLE, tagqng_able); 1900 for (tid = 0; tid <= ADW_MAX_TID; tid++) { 1901 ADW_READ_BYTE_LRAM(iot, ioh, ADW_MC_NUMBER_OF_MAX_CMD + tid, 1902 max_cmd[tid]); 1903 } 1904 1905 /* 1906 * Force the AdwInitAscDriver() function to perform a SCSI Bus Reset 1907 * by clearing the BIOS signature word. 1908 * The initialization functions assumes a SCSI Bus Reset is not 1909 * needed if the BIOS signature word is present. 1910 */ 1911 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_BIOS_SIGNATURE, bios_sig); 1912 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_BIOS_SIGNATURE, 0); 1913 1914 /* 1915 * Stop chip and reset it. 1916 */ 1917 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_RISC_CSR, ADW_RISC_CSR_STOP); 1918 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_CTRL_REG, 1919 ADW_CTRL_REG_CMD_RESET); 1920 AdwSleepMilliSecond(100); 1921 ADW_WRITE_WORD_REGISTER(iot, ioh, IOPW_CTRL_REG, 1922 ADW_CTRL_REG_CMD_WR_IO_REG); 1923 1924 /* 1925 * Reset Adv Library error code, if any, and try 1926 * re-initializing the chip. 1927 * Then translate initialization return value to status value. 1928 */ 1929 status = (AdwInitDriver(sc) == 0)? ADW_TRUE : ADW_FALSE; 1930 1931 /* 1932 * Restore the BIOS signature word. 1933 */ 1934 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_BIOS_SIGNATURE, bios_sig); 1935 1936 /* 1937 * Restore per TID negotiated values. 1938 */ 1939 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_WDTR_ABLE, wdtr_able); 1940 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_SDTR_ABLE, sdtr_able); 1941 if (sc->chip_type == ADW_CHIP_ASC38C1600) { 1942 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_PPR_ABLE, ppr_able); 1943 } 1944 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_TAGQNG_ABLE, tagqng_able); 1945 for (tid = 0; tid <= ADW_MAX_TID; tid++) { 1946 ADW_WRITE_BYTE_LRAM(iot, ioh, ADW_MC_NUMBER_OF_MAX_CMD + tid, 1947 max_cmd[tid]); 1948 } 1949 1950 return status; 1951 } 1952 1953 1954 /* 1955 * Adv Library Interrupt Service Routine 1956 * 1957 * This function is called by a driver's interrupt service routine. 1958 * The function disables and re-enables interrupts. 1959 * 1960 * When a microcode idle command is completed, the ADV_DVC_VAR 1961 * 'idle_cmd_done' field is set to ADW_TRUE. 1962 * 1963 * Note: AdwISR() can be called when interrupts are disabled or even 1964 * when there is no hardware interrupt condition present. It will 1965 * always check for completed idle commands and microcode requests. 1966 * This is an important feature that shouldn't be changed because it 1967 * allows commands to be completed from polling mode loops. 1968 * 1969 * Return: 1970 * ADW_TRUE(1) - interrupt was pending 1971 * ADW_FALSE(0) - no interrupt was pending 1972 */ 1973 int 1974 AdwISR(ADW_SOFTC *sc) 1975 { 1976 bus_space_tag_t iot = sc->sc_iot; 1977 bus_space_handle_t ioh = sc->sc_ioh; 1978 u_int8_t int_stat; 1979 ADW_CARRIER *free_carrp/*, *ccb_carr*/; 1980 u_int32_t irq_next_pa; 1981 ADW_SCSI_REQ_Q *scsiq; 1982 ADW_CCB *ccb; 1983 int s; 1984 1985 1986 s = splbio(); 1987 1988 /* Reading the register clears the interrupt. */ 1989 int_stat = ADW_READ_BYTE_REGISTER(iot, ioh, IOPB_INTR_STATUS_REG); 1990 1991 if ((int_stat & (ADW_INTR_STATUS_INTRA | ADW_INTR_STATUS_INTRB | 1992 ADW_INTR_STATUS_INTRC)) == 0) { 1993 splx(s); 1994 return ADW_FALSE; 1995 } 1996 1997 /* 1998 * Notify the driver of an asynchronous microcode condition by 1999 * calling the ADV_DVC_VAR.async_callback function. The function 2000 * is passed the microcode ADW_MC_INTRB_CODE byte value. 2001 */ 2002 if (int_stat & ADW_INTR_STATUS_INTRB) { 2003 u_int8_t intrb_code; 2004 2005 ADW_READ_BYTE_LRAM(iot, ioh, ADW_MC_INTRB_CODE, intrb_code); 2006 2007 if (sc->chip_type == ADW_CHIP_ASC3550 || 2008 sc->chip_type == ADW_CHIP_ASC38C0800) { 2009 if (intrb_code == ADV_ASYNC_CARRIER_READY_FAILURE && 2010 sc->carr_pending_cnt != 0) { 2011 ADW_WRITE_BYTE_REGISTER(iot, ioh, 2012 IOPB_TICKLE, ADW_TICKLE_A); 2013 if (sc->chip_type == ADW_CHIP_ASC3550) { 2014 ADW_WRITE_BYTE_REGISTER(iot, ioh, 2015 IOPB_TICKLE, ADW_TICKLE_NOP); 2016 } 2017 } 2018 } 2019 2020 if (sc->async_callback != 0) { 2021 (*(ADW_ASYNC_CALLBACK)sc->async_callback)(sc, intrb_code); 2022 } 2023 } 2024 2025 /* 2026 * Check if the IRQ stopper carrier contains a completed request. 2027 */ 2028 while (((le32toh(irq_next_pa = sc->irq_sp->next_ba)) & ASC_RQ_DONE) != 0) 2029 { 2030 #if ADW_DEBUG 2031 printf("irq 0x%x, 0x%x, 0x%x, 0x%x\n", 2032 sc->irq_sp->carr_id, 2033 sc->irq_sp->carr_ba, 2034 sc->irq_sp->areq_ba, 2035 sc->irq_sp->next_ba); 2036 #endif 2037 /* 2038 * Get a pointer to the newly completed ADW_SCSI_REQ_Q 2039 * structure. 2040 * The RISC will have set 'areq_ba' to a virtual address. 2041 * 2042 * The firmware will have copied the ASC_SCSI_REQ_Q.ccb_ptr 2043 * field to the carrier ADV_CARR_T.areq_ba field. 2044 * The conversion below complements the conversion of 2045 * ASC_SCSI_REQ_Q.scsiq_ptr' in AdwExeScsiQueue(). 2046 */ 2047 ccb = adw_ccb_phys_kv(sc, sc->irq_sp->areq_ba); 2048 scsiq = &ccb->scsiq; 2049 scsiq->ccb_ptr = sc->irq_sp->areq_ba; 2050 2051 /* 2052 * Request finished with good status and the queue was not 2053 * DMAed to host memory by the firmware. Set all status fields 2054 * to indicate good status. 2055 */ 2056 if ((le32toh(irq_next_pa) & ASC_RQ_GOOD) != 0) { 2057 scsiq->done_status = QD_NO_ERROR; 2058 scsiq->host_status = scsiq->scsi_status = 0; 2059 scsiq->data_cnt = 0L; 2060 } 2061 2062 /* 2063 * Advance the stopper pointer to the next carrier 2064 * ignoring the lower four bits. Free the previous 2065 * stopper carrier. 2066 */ 2067 free_carrp = sc->irq_sp; 2068 sc->irq_sp = ADW_CARRIER_VADDR(sc, ASC_GET_CARRP(irq_next_pa)); 2069 2070 free_carrp->next_ba = (sc->carr_freelist == NULL) ? 0 2071 : sc->carr_freelist->carr_ba; 2072 sc->carr_freelist = free_carrp; 2073 sc->carr_pending_cnt--; 2074 2075 /* 2076 * Clear request microcode control flag. 2077 */ 2078 scsiq->cntl = 0; 2079 2080 /* 2081 * Check Condition handling 2082 */ 2083 /* 2084 * If the command that completed was a SCSI INQUIRY and 2085 * LUN 0 was sent the command, then process the INQUIRY 2086 * command information for the device. 2087 */ 2088 if (scsiq->done_status == QD_NO_ERROR && 2089 scsiq->cdb[0] == INQUIRY && 2090 scsiq->target_lun == 0) { 2091 AdwInquiryHandling(sc, scsiq); 2092 } 2093 2094 /* 2095 * Notify the driver of the completed request by passing 2096 * the ADW_SCSI_REQ_Q pointer to its callback function. 2097 */ 2098 (*(ADW_ISR_CALLBACK)sc->isr_callback)(sc, scsiq); 2099 /* 2100 * Note: After the driver callback function is called, 'scsiq' 2101 * can no longer be referenced. 2102 * 2103 * Fall through and continue processing other completed 2104 * requests... 2105 */ 2106 } 2107 2108 splx(s); 2109 2110 return ADW_TRUE; 2111 } 2112 2113 2114 /* 2115 * Send an idle command to the chip and wait for completion. 2116 * 2117 * Command completion is polled for once per microsecond. 2118 * 2119 * The function can be called from anywhere including an interrupt handler. 2120 * But the function is not re-entrant, so it uses the splbio/splx() 2121 * functions to prevent reentrancy. 2122 * 2123 * Return Values: 2124 * ADW_TRUE - command completed successfully 2125 * ADW_FALSE - command failed 2126 * ADW_ERROR - command timed out 2127 */ 2128 int 2129 AdwSendIdleCmd(ADW_SOFTC *sc, u_int16_t idle_cmd, u_int32_t idle_cmd_parameter) 2130 { 2131 bus_space_tag_t iot = sc->sc_iot; 2132 bus_space_handle_t ioh = sc->sc_ioh; 2133 u_int16_t result; 2134 u_int32_t i, j, s; 2135 2136 s = splbio(); 2137 2138 /* 2139 * Clear the idle command status which is set by the microcode 2140 * to a non-zero value to indicate when the command is completed. 2141 */ 2142 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_IDLE_CMD_STATUS, (u_int16_t) 0); 2143 2144 /* 2145 * Write the idle command value after the idle command parameter 2146 * has been written to avoid a race condition. If the order is not 2147 * followed, the microcode may process the idle command before the 2148 * parameters have been written to LRAM. 2149 */ 2150 ADW_WRITE_DWORD_LRAM(iot, ioh, ADW_MC_IDLE_CMD_PARAMETER, 2151 idle_cmd_parameter); 2152 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_IDLE_CMD, idle_cmd); 2153 2154 /* 2155 * Tickle the RISC to tell it to process the idle command. 2156 */ 2157 ADW_WRITE_BYTE_REGISTER(iot, ioh, IOPB_TICKLE, ADW_TICKLE_B); 2158 if (sc->chip_type == ADW_CHIP_ASC3550) { 2159 /* 2160 * Clear the tickle value. In the ASC-3550 the RISC flag 2161 * command 'clr_tickle_b' does not work unless the host 2162 * value is cleared. 2163 */ 2164 ADW_WRITE_BYTE_REGISTER(iot, ioh, IOPB_TICKLE, ADW_TICKLE_NOP); 2165 } 2166 2167 /* Wait for up to 100 millisecond for the idle command to timeout. */ 2168 for (i = 0; i < SCSI_WAIT_100_MSEC; i++) { 2169 /* Poll once each microsecond for command completion. */ 2170 for (j = 0; j < SCSI_US_PER_MSEC; j++) { 2171 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_IDLE_CMD_STATUS, 2172 result); 2173 if (result != 0) { 2174 splx(s); 2175 return result; 2176 } 2177 AdwDelayMicroSecond(1); 2178 } 2179 } 2180 2181 splx(s); 2182 return ADW_ERROR; 2183 } 2184 2185 2186 /* 2187 * Inquiry Information Byte 7 Handling 2188 * 2189 * Handle SCSI Inquiry Command information for a device by setting 2190 * microcode operating variables that affect WDTR, SDTR, and Tag 2191 * Queuing. 2192 */ 2193 static void 2194 AdwInquiryHandling(ADW_SOFTC *sc, ADW_SCSI_REQ_Q *scsiq) 2195 { 2196 #ifndef FAILSAFE 2197 bus_space_tag_t iot = sc->sc_iot; 2198 bus_space_handle_t ioh = sc->sc_ioh; 2199 u_int8_t tid; 2200 struct scsipi_inquiry_data *inq; 2201 u_int16_t tidmask; 2202 u_int16_t cfg_word; 2203 2204 2205 /* 2206 * AdwInquiryHandling() requires up to INQUIRY information Byte 7 2207 * to be available. 2208 * 2209 * If less than 8 bytes of INQUIRY information were requested or less 2210 * than 8 bytes were transferred, then return. cdb[4] is the request 2211 * length and the ADW_SCSI_REQ_Q 'data_cnt' field is set by the 2212 * microcode to the transfer residual count. 2213 */ 2214 2215 if (scsiq->cdb[4] < 8 || (scsiq->cdb[4] - scsiq->data_cnt) < 8) { 2216 return; 2217 } 2218 2219 tid = scsiq->target_id; 2220 2221 inq = (struct scsipi_inquiry_data *) scsiq->vdata_addr; 2222 2223 /* 2224 * WDTR, SDTR, and Tag Queuing cannot be enabled for old devices. 2225 */ 2226 if (((inq->response_format & SID_RespDataFmt) < 2) /*SCSI-1 | CCS*/ && 2227 ((inq->version & SID_ANSII) < 2)) { 2228 return; 2229 } else { 2230 /* 2231 * INQUIRY Byte 7 Handling 2232 * 2233 * Use a device's INQUIRY byte 7 to determine whether it 2234 * supports WDTR, SDTR, and Tag Queuing. If the feature 2235 * is enabled in the EEPROM and the device supports the 2236 * feature, then enable it in the microcode. 2237 */ 2238 2239 tidmask = ADW_TID_TO_TIDMASK(tid); 2240 2241 /* 2242 * Wide Transfers 2243 * 2244 * If the EEPROM enabled WDTR for the device and the device 2245 * supports wide bus (16 bit) transfers, then turn on the 2246 * device's 'wdtr_able' bit and write the new value to the 2247 * microcode. 2248 */ 2249 #ifdef SCSI_ADW_WDTR_DISABLE 2250 if(!(tidmask & SCSI_ADW_WDTR_DISABLE)) 2251 #endif /* SCSI_ADW_WDTR_DISABLE */ 2252 if ((sc->wdtr_able & tidmask) && (inq->flags3 & SID_WBus16)) { 2253 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_WDTR_ABLE, 2254 cfg_word); 2255 if ((cfg_word & tidmask) == 0) { 2256 cfg_word |= tidmask; 2257 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_WDTR_ABLE, 2258 cfg_word); 2259 2260 /* 2261 * Clear the microcode "SDTR negotiation" and 2262 * "WDTR negotiation" done indicators for the 2263 * target to cause it to negotiate with the new 2264 * setting set above. 2265 * WDTR when accepted causes the target to enter 2266 * asynchronous mode, so SDTR must be negotiated 2267 */ 2268 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_SDTR_DONE, 2269 cfg_word); 2270 cfg_word &= ~tidmask; 2271 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_SDTR_DONE, 2272 cfg_word); 2273 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_WDTR_DONE, 2274 cfg_word); 2275 cfg_word &= ~tidmask; 2276 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_WDTR_DONE, 2277 cfg_word); 2278 } 2279 } 2280 2281 /* 2282 * Synchronous Transfers 2283 * 2284 * If the EEPROM enabled SDTR for the device and the device 2285 * supports synchronous transfers, then turn on the device's 2286 * 'sdtr_able' bit. Write the new value to the microcode. 2287 */ 2288 #ifdef SCSI_ADW_SDTR_DISABLE 2289 if(!(tidmask & SCSI_ADW_SDTR_DISABLE)) 2290 #endif /* SCSI_ADW_SDTR_DISABLE */ 2291 if ((sc->sdtr_able & tidmask) && (inq->flags3 & SID_Sync)) { 2292 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_SDTR_ABLE,cfg_word); 2293 if ((cfg_word & tidmask) == 0) { 2294 cfg_word |= tidmask; 2295 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_SDTR_ABLE, 2296 cfg_word); 2297 2298 /* 2299 * Clear the microcode "SDTR negotiation" 2300 * done indicator for the target to cause it 2301 * to negotiate with the new setting set above. 2302 */ 2303 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_SDTR_DONE, 2304 cfg_word); 2305 cfg_word &= ~tidmask; 2306 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_SDTR_DONE, 2307 cfg_word); 2308 } 2309 } 2310 /* 2311 * If the Inquiry data included enough space for the SPI-3 2312 * Clocking field, then check if DT mode is supported. 2313 */ 2314 if (sc->chip_type == ADW_CHIP_ASC38C1600 && 2315 (scsiq->cdb[4] >= 57 || 2316 (scsiq->cdb[4] - scsiq->data_cnt) >= 57)) { 2317 /* 2318 * PPR (Parallel Protocol Request) Capable 2319 * 2320 * If the device supports DT mode, then it must be 2321 * PPR capable. 2322 * The PPR message will be used in place of the SDTR 2323 * and WDTR messages to negotiate synchronous speed 2324 * and offset, transfer width, and protocol options. 2325 */ 2326 if((inq->flags4 & SID_Clocking) & SID_CLOCKING_DT_ONLY){ 2327 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_PPR_ABLE, 2328 sc->ppr_able); 2329 sc->ppr_able |= tidmask; 2330 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_PPR_ABLE, 2331 sc->ppr_able); 2332 } 2333 } 2334 2335 /* 2336 * If the EEPROM enabled Tag Queuing for the device and the 2337 * device supports Tag Queueing, then turn on the device's 2338 * 'tagqng_enable' bit in the microcode and set the microcode 2339 * maximum command count to the ADV_DVC_VAR 'max_dvc_qng' 2340 * value. 2341 * 2342 * Tag Queuing is disabled for the BIOS which runs in polled 2343 * mode and would see no benefit from Tag Queuing. Also by 2344 * disabling Tag Queuing in the BIOS devices with Tag Queuing 2345 * bugs will at least work with the BIOS. 2346 */ 2347 #ifdef SCSI_ADW_TAGQ_DISABLE 2348 if(!(tidmask & SCSI_ADW_TAGQ_DISABLE)) 2349 #endif /* SCSI_ADW_TAGQ_DISABLE */ 2350 if ((sc->tagqng_able & tidmask) && (inq->flags3 & SID_CmdQue)) { 2351 ADW_READ_WORD_LRAM(iot, ioh, ADW_MC_TAGQNG_ABLE, 2352 cfg_word); 2353 cfg_word |= tidmask; 2354 ADW_WRITE_WORD_LRAM(iot, ioh, ADW_MC_TAGQNG_ABLE, 2355 cfg_word); 2356 2357 ADW_WRITE_BYTE_LRAM(iot, ioh, 2358 ADW_MC_NUMBER_OF_MAX_CMD + tid, 2359 sc->max_dvc_qng); 2360 } 2361 } 2362 #endif /* FAILSAFE */ 2363 } 2364 2365 2366 static void 2367 AdwSleepMilliSecond(u_int32_t n) 2368 { 2369 2370 DELAY(n * 1000); 2371 } 2372 2373 2374 static void 2375 AdwDelayMicroSecond(u_int32_t n) 2376 { 2377 2378 DELAY(n); 2379 } 2380 2381
Indexes created Tue Oct 21 16:10:11 GMT 2025