xref: /src/sys/dev/ic/cs89x0reg.h

/*	$NetBSD: cs89x0reg.h,v 1.2 2004/02/04 15:43:14 augustss Exp $	*/

/*
 * Copyright 1997
 * Digital Equipment Corporation. All rights reserved.
 *
 * This software is furnished under license and may be used and
 * copied only in accordance with the following terms and conditions.
 * Subject to these conditions, you may download, copy, install,
 * use, modify and distribute this software in source and/or binary
 * form. No title or ownership is transferred hereby.
 *
 * 1) Any source code used, modified or distributed must reproduce
 *    and retain this copyright notice and list of conditions as
 *    they appear in the source file.
 *
 * 2) No right is granted to use any trade name, trademark, or logo of
 *    Digital Equipment Corporation. Neither the "Digital Equipment
 *    Corporation" name nor any trademark or logo of Digital Equipment
 *    Corporation may be used to endorse or promote products derived
 *    from this software without the prior written permission of
 *    Digital Equipment Corporation.
 *
 * 3) This software is provided "AS-IS" and any express or implied
 *    warranties, including but not limited to, any implied warranties
 *    of merchantability, fitness for a particular purpose, or
 *    non-infringement are disclaimed. In no event shall DIGITAL be
 *    liable for any damages whatsoever, and in particular, DIGITAL
 *    shall not be liable for special, indirect, consequential, or
 *    incidental damages or damages for lost profits, loss of
 *    revenue or loss of use, whether such damages arise in contract,
 *    negligence, tort, under statute, in equity, at law or otherwise,
 *    even if advised of the possibility of such damage.
 */

/*
**++
**  FACILITY  Crystal CS8900 Ethernet driver register description
**
**  ABSTRACT
**
**     This module provides CS8900 register definitions
**
**  AUTHORS
**
**     Peter Dettori   SEA - Software Engineering.
**
**  CREATION DATE:
**
**       13-Feb-1997.
**
**  MODIFICATION HISTORY:
**
**--
*/

#ifndef _DEV_IC_CS89X0REG_H_
#define	_DEV_IC_CS89X0REG_H_

/*
 * The CS8900 has 8 2-byte registers in I/O space.
 */
#define	CS8900_IOSIZE	16

/*
 * The CS8900 has a 4k memory space.
 */
#define	CS8900_MEMSIZE	4096

/*
 * Size of the DMA area used for packet reception.
 */
#if 0
#define	CS8900_DMASIZE	(64*1024)
#else
#define	CS8900_DMASIZE	(16*1024)
#endif

/*
 * Validate various parameters.
 */
#define	CS8900_MEMBASE_ISVALID(x)	(((x) & (CS8900_MEMSIZE - 1)) == 0)
#define	CS8900_IRQ_ISVALID(x)		((x) == 5 || (x) == 10 ||	\
					 (x) == 11 || (x) == 12)

/* Chip Identification (PacketPage registers) */

#define EISA_NUM_CRYSTAL	0x630E
#define PROD_ID_MASK		0xE000
#define PROD_ID_CS8900		0x0000
#define PROD_ID_CS8920		0x4000
#define PROD_ID_CS8920M		0x6000
#define PROD_REV_MASK		0x1F00


/* IO Port Offsets */

#define PORT_RXTX_DATA		0x0000
#define PORT_RXTX_DATA_1	0x0002
#define PORT_TX_CMD		0x0004
#define PORT_TX_LENGTH		0x0006
#define PORT_ISQ		0x0008
#define PORT_PKTPG_PTR		0x000A
#define PORT_PKTPG_DATA		0x000C
#define PORT_PKTPG_DATA_1	0x000E


/* PacketPage Offsets */

#define PKTPG_EISA_NUM		0x0000
#define PKTPG_PRODUCT_ID	0x0002
#define PKTPG_IO_BASE		0x0020
#define PKTPG_INT_NUM		0x0022
#define PKTPG_DMA_CHANNEL	0x0024
#define PKTPG_DMA_START_FRAME	0x0026
#define PKTPG_DMA_FRAME_COUNT	0x0028
#define PKTPG_DMA_BYTE_COUNT	0x002A
#define PKTPG_MEM_BASE		0x002C
#define PKTPG_EEPROM_CMD	0x0040
#define PKTPG_EEPROM_DATA	0x0042
#define PKTPG_FRAME_BYTE_COUNT	0x0050
#define PKTPG_RX_CFG		0x0102
#define PKTPG_RX_CTL		0x0104
#define PKTPG_TX_CFG		0x0106
#define PKTPG_BUF_CFG		0x010A
#define PKTPG_LINE_CTL		0x0112
#define PKTPG_SELF_CTL		0x0114
#define PKTPG_BUS_CTL		0x0116
#define PKTPG_TEST_CTL		0x0118
#define	PKTPG_AUTONEG_CTL	0x011C
#define PKTPG_ISQ		0x0120
#define PKTPG_RX_EVENT		0x0124
#define PKTPG_TX_EVENT		0x0128
#define PKTPG_BUF_EVENT		0x012C
#define PKTPG_RX_MISS		0x0130
#define PKTPG_TX_COL		0x0132
#define PKTPG_LINE_ST		0x0134
#define PKTPG_SELF_ST		0x0136
#define PKTPG_BUS_ST		0x0138
#define	PKTPG_TDR		0x013c
#define	PKTPG_AUTONEG_ST	0x013e
#define PKTPG_TX_CMD		0x0144
#define PKTPG_TX_LENGTH		0x0146
#define PKTPG_LOG_ADDR		0x0150	/* logical address filter hash tbl */
#define PKTPG_IND_ADDR		0x0158
#define PKTPG_8920_INT_NUM	0x0370
#define PKTPG_8920_DMA_CHANNEL	0x0374
#define PKTPG_RX_STATUS		0x0400
#define PKTPG_RX_LENGTH		0x0402
#define PKTPG_RX_FRAME		0x0404
#define PKTPG_TX_FRAME		0x0A00


/* EEPROM Offsets */

#define EEPROM_MAC		0x0009
#define EEPROM_IND_ADDR_H	0x001C
#define EEPROM_IND_ADDR_M	0x001D
#define EEPROM_IND_ADDR_L	0x001E
#define EEPROM_ISA_CFG		0x001F
#define EEPROM_MEM_BASE		0x0020
#define EEPROM_XMIT_CTL		0x0023
#define EEPROM_ADPTR_CFG	0x0024


/* Register Numbers */

#define REG_NUM_MASK		0x003F
#define REG_NUM_RX_EVENT	0x0004
#define REG_NUM_TX_EVENT	0x0008
#define REG_NUM_BUF_EVENT	0x000C
#define REG_NUM_RX_MISS		0x0010
#define REG_NUM_TX_COL		0x0012


/* Self Control Register */

#define SELF_CTL_RESET		0x0040
#define SELF_CTL_HC1E		0x2000
#define SELF_CTL_HCB1		0x8000


/* Self Status Register */

#define SELF_ST_INIT_DONE	0x0080
#define SELF_ST_SI_BUSY		0x0100
#define SELF_ST_EEP_PRES	0x0200
#define SELF_ST_EEP_OK		0x0400
#define SELF_ST_EL_PRES		0x0800


/* EEPROM Command Register */

#define EEPROM_WRITE_DISABLE	0x0000
#define EEPROM_WRITE_ENABLE	0x00F0
#define EEPROM_CMD_WRITE	0x0100
#define EEPROM_CMD_READ		0x0200
#define EEPROM_CMD_ELSEL	0x0400


/* Bus Control Register */

#define BUS_CTL_RESET_DMA	0x0040
#define BUS_CTL_USE_SA		0x0200
#define BUS_CTL_MEM_MODE	0x0400
#define BUS_CTL_DMA_BURST	0x0800
#define BUS_CTL_IOCHRDY		0x1000
#define BUS_CTL_DMA_SIZE	0x2000
#define BUS_CTL_INT_ENBL	0x8000


/* Bus Status Register */

#define BUS_ST_TX_BID_ERR	0x0080
#define BUS_ST_RDY4TXNOW	0x0100


/* Line Control Register */

#define LINE_CTL_RX_ON		0x0040
#define LINE_CTL_TX_ON		0x0080
#define LINE_CTL_AUI_ONLY	0x0100
#define LINE_CTL_10BASET	0x0000
#define LINE_CTL_AUTO_SEL	0x0200


/* Test Control Register */

#define TEST_CTL_DIS_LT		0x0080
#define TEST_CTL_ENDEC_LP	0x0200
#define TEST_CTL_AUI_LOOP	0x0400
#define TEST_CTL_DIS_BKOFF	0x0800
#define TEST_CTL_FDX		0x4000


/* Receiver Configuration Register */

#define RX_CFG_SKIP		0x0040
#define RX_CFG_RX_OK_IE		0x0100
#define RX_CFG_RX_DMA_ONLY	0x0200
#define RX_CFG_CRC_ERR_IE	0x1000
#define RX_CFG_RUNT_IE		0x2000
#define RX_CFG_X_DATA_IE	0x4000
#define RX_CFG_ALL_IE		0x7100


/* Receiver Event Register */

#define RX_EVENT_DRIBBLE	0x0080
#define RX_EVENT_RX_OK		0x0100
#define RX_EVENT_IND_ADDR	0x0400
#define RX_EVENT_BCAST		0x0800
#define RX_EVENT_CRC_ERR	0x1000
#define RX_EVENT_RUNT		0x2000
#define RX_EVENT_X_DATA		0x4000


/* Receiver Control Register */

#define RX_CTL_INDHASH_A	0x0040
#define RX_CTL_PROMISC_A	0x0080
#define RX_CTL_RX_OK_A		0x0100
#define RX_CTL_MCAST_A		0x0200
#define RX_CTL_IND_A		0x0400
#define RX_CTL_BCAST_A		0x0800
#define RX_CTL_CRC_ERR_A	0x1000
#define RX_CTL_RUNT_A		0x2000
#define RX_CTL_X_DATA_A		0x4000


/* Transmit Configuration Register */

#define TX_CFG_LOSS_CRS_IE	0x0040
#define TX_CFG_SQE_ERR_IE	0x0080
#define TX_CFG_TX_OK_IE		0x0100
#define TX_CFG_OUT_WIN_IE	0x0200
#define TX_CFG_JABBER_IE	0x0400
#define TX_CFG_16_COLL_IE	0x8000
#define TX_CFG_ALL_IE		0x8FC0



/* Transmit Configuration Register */

#define TX_EVENT_LOSS_CRS	0x0040
#define TX_EVENT_SQE_ERR	0x0080
#define TX_EVENT_TX_OK		0x0100
#define TX_EVENT_OUT_WIN	0x0200
#define TX_EVENT_JABBER		0x0400
#define TX_EVENT_COLL_MASK	0x7800
#define TX_EVENT_16_COLL	0x8000


/* Transmit Command Register */

#define TX_CMD_START_5		0x0000
#define TX_CMD_START_381	0x0080
#define TX_CMD_START_1021	0x0040
#define TX_CMD_START_ALL	0x00C0
#define TX_CMD_FORCE		0x0100
#define TX_CMD_ONE_COLL		0x0200
#define TX_CMD_NO_CRC		0x1000
#define TX_CMD_NO_PAD		0x2000


/* Buffer Configuration Register */

#define BUF_CFG_SW_INT		0x0040
#define BUF_CFG_RX_DMA_IE	0x0080
#define BUF_CFG_RDY4TX_IE	0x0100
#define BUF_CFG_RX_MISS_IE	0x0400
#define BUF_CFG_TX_UNDR_IE	0x0200
#define BUF_CFG_RX_128_IE	0x0800
#define BUF_CFG_TX_COL_OVER_IE	0x1000
#define BUF_CFG_RX_MISS_OVER_IE	0x2000
#define BUF_CFG_RX_DEST_IE	0x8000

/* Buffer Event Register */

#define BUF_EVENT_SW_INT	0x0040
#define BUF_EVENT_RX_DMA	0x0080
#define BUF_EVENT_RDY4TX	0x0100
#define BUF_EVENT_TX_UNDR	0x0200
#define BUF_EVENT_RX_MISS	0x0400
#define BUF_EVENT_RX_128	0x0800
#define BUF_EVENT_RX_DEST	0x8000


/* Autonegotiation Control Register */

#define	AUTOCTL_NEG_NOW		0x0040
#define	AUTOCTL_ALLOW_FDX	0x0080
#define	AUTOCTL_NEG_ENABLE	0x0100
#define	AUTOCTL_NLP_ENABLE	0x0200
#define	AUTOCTL_FORCE_FDX	0x8000


/* Autonegotiation Status Register */

#define	AUTOST_NEG_BUSY		0x0080
#define	AUTOST_FLP_LINK		0x0100
#define	AUTOST_FLP_LINK_GOOD	0x0800
#define	AUTOST_LINK_FAULT	0x1000
#define	AUTOST_HDX_ACTIVE	0x4000
#define	AUTOST_FDX_ACTIVE	0x8000


/* ISA Configuration from EEPROM */

#define ISA_CFG_IRQ_MASK	0x000F
#define ISA_CFG_USE_SA		0x0080
#define ISA_CFG_IOCHRDY		0x0100
#define ISA_CFG_MEM_MODE	0x8000


/* Memory Base from EEPROM */

#define MEM_BASE_MASK		0xFFF0


/* Adpater Configuration from EEPROM */

#define ADPTR_CFG_MEDIA		0x0060
#define ADPTR_CFG_10BASET	0x0020
#define ADPTR_CFG_AUI		0x0040
#define ADPTR_CFG_10BASE2	0x0060
#define ADPTR_CFG_DCDC_POL	0x0080


/* Transmission Control from EEPROM */

#define XMIT_CTL_FDX		0x8000


/* Miscellaneous definitions */

#define MAXLOOP			0x8888
#define RXBUFCOUNT		16
#define MC_LOANED		5

#endif /* _DEV_IC_CS89X0REG_H_ */