isp_target.h revision 1.20
1 /* $NetBSD: isp_target.h,v 1.20 2003/08/07 01:12:16 mjacob Exp $ */ 2 /* 3 * This driver, which is contained in NetBSD in the files: 4 * 5 * sys/dev/ic/isp.c 6 * sys/dev/ic/isp_inline.h 7 * sys/dev/ic/isp_netbsd.c 8 * sys/dev/ic/isp_netbsd.h 9 * sys/dev/ic/isp_target.c 10 * sys/dev/ic/isp_target.h 11 * sys/dev/ic/isp_tpublic.h 12 * sys/dev/ic/ispmbox.h 13 * sys/dev/ic/ispreg.h 14 * sys/dev/ic/ispvar.h 15 * sys/microcode/isp/asm_sbus.h 16 * sys/microcode/isp/asm_1040.h 17 * sys/microcode/isp/asm_1080.h 18 * sys/microcode/isp/asm_12160.h 19 * sys/microcode/isp/asm_2100.h 20 * sys/microcode/isp/asm_2200.h 21 * sys/pci/isp_pci.c 22 * sys/sbus/isp_sbus.c 23 * 24 * Is being actively maintained by Matthew Jacob (mjacob (at) netbsd.org). 25 * This driver also is shared source with FreeBSD, OpenBSD, Linux, Solaris, 26 * Linux versions. This tends to be an interesting maintenance problem. 27 * 28 * Please coordinate with Matthew Jacob on changes you wish to make here. 29 */ 30 /* 31 * Qlogic Target Mode Structure and Flag Definitions 32 * 33 * Copyright (c) 1997, 1998 34 * Patrick Stirling 35 * pms (at) psconsult.com 36 * All rights reserved. 37 * 38 * Additional Copyright (c) 1999, 2000, 2001 39 * Matthew Jacob 40 * mjacob (at) feral.com 41 * All rights reserved. 42 * 43 * 44 * Redistribution and use in source and binary forms, with or without 45 * modification, are permitted provided that the following conditions 46 * are met: 47 * 1. Redistributions of source code must retain the above copyright 48 * notice immediately at the beginning of the file, without modification, 49 * this list of conditions, and the following disclaimer. 50 * 2. The name of the author may not be used to endorse or promote products 51 * derived from this software without specific prior written permission. 52 * 53 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 54 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 55 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 56 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR 57 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 58 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 59 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 60 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 61 * SUCH DAMAGE. 62 * 63 */ 64 #ifndef _ISP_TARGET_H 65 #define _ISP_TARGET_H 66 67 #define QLTM_SENSELEN 18 /* non-FC cards only */ 68 #define QLTM_SVALID 0x80 69 70 /* 71 * Structure for Enable Lun and Modify Lun queue entries 72 */ 73 typedef struct { 74 isphdr_t le_header; 75 u_int32_t le_reserved; 76 u_int8_t le_lun; 77 u_int8_t le_rsvd; 78 u_int8_t le_ops; /* Modify LUN only */ 79 u_int8_t le_tgt; /* Not for FC */ 80 u_int32_t le_flags; /* Not for FC */ 81 u_int8_t le_status; 82 u_int8_t le_reserved2; 83 u_int8_t le_cmd_count; 84 u_int8_t le_in_count; 85 u_int8_t le_cdb6len; /* Not for FC */ 86 u_int8_t le_cdb7len; /* Not for FC */ 87 u_int16_t le_timeout; 88 u_int16_t le_reserved3[20]; 89 } lun_entry_t; 90 91 /* 92 * le_flags values 93 */ 94 #define LUN_TQAE 0x00000002 /* bit1 Tagged Queue Action Enable */ 95 #define LUN_DSSM 0x01000000 /* bit24 Disable Sending SDP Message */ 96 #define LUN_DISAD 0x02000000 /* bit25 Disable autodisconnect */ 97 #define LUN_DM 0x40000000 /* bit30 Disconnects Mandatory */ 98 99 /* 100 * le_ops values 101 */ 102 #define LUN_CCINCR 0x01 /* increment command count */ 103 #define LUN_CCDECR 0x02 /* decrement command count */ 104 #define LUN_ININCR 0x40 /* increment immed. notify count */ 105 #define LUN_INDECR 0x80 /* decrement immed. notify count */ 106 107 /* 108 * le_status values 109 */ 110 #define LUN_OK 0x01 /* we be rockin' */ 111 #define LUN_ERR 0x04 /* request completed with error */ 112 #define LUN_INVAL 0x06 /* invalid request */ 113 #define LUN_NOCAP 0x16 /* can't provide requested capability */ 114 #define LUN_ENABLED 0x3E /* LUN already enabled */ 115 116 /* 117 * Immediate Notify Entry structure 118 */ 119 #define IN_MSGLEN 8 /* 8 bytes */ 120 #define IN_RSVDLEN 8 /* 8 words */ 121 typedef struct { 122 isphdr_t in_header; 123 u_int32_t in_reserved; 124 u_int8_t in_lun; /* lun */ 125 u_int8_t in_iid; /* initiator */ 126 u_int8_t in_reserved2; 127 u_int8_t in_tgt; /* target */ 128 u_int32_t in_flags; 129 u_int8_t in_status; 130 u_int8_t in_rsvd2; 131 u_int8_t in_tag_val; /* tag value */ 132 u_int8_t in_tag_type; /* tag type */ 133 u_int16_t in_seqid; /* sequence id */ 134 u_int8_t in_msg[IN_MSGLEN]; /* SCSI message bytes */ 135 u_int16_t in_reserved3[IN_RSVDLEN]; 136 u_int8_t in_sense[QLTM_SENSELEN];/* suggested sense data */ 137 } in_entry_t; 138 139 typedef struct { 140 isphdr_t in_header; 141 u_int32_t in_reserved; 142 u_int8_t in_lun; /* lun */ 143 u_int8_t in_iid; /* initiator */ 144 u_int16_t in_scclun; 145 u_int32_t in_reserved2; 146 u_int16_t in_status; 147 u_int16_t in_task_flags; 148 u_int16_t in_seqid; /* sequence id */ 149 } in_fcentry_t; 150 151 /* 152 * Values for the in_status field 153 */ 154 #define IN_REJECT 0x0D /* Message Reject message received */ 155 #define IN_RESET 0x0E /* Bus Reset occurred */ 156 #define IN_NO_RCAP 0x16 /* requested capability not available */ 157 #define IN_IDE_RECEIVED 0x33 /* Initiator Detected Error msg received */ 158 #define IN_RSRC_UNAVAIL 0x34 /* resource unavailable */ 159 #define IN_MSG_RECEIVED 0x36 /* SCSI message received */ 160 #define IN_ABORT_TASK 0x20 /* task named in RX_ID is being aborted (FC) */ 161 #define IN_PORT_LOGOUT 0x29 /* port has logged out (FC) */ 162 #define IN_PORT_CHANGED 0x2A /* port changed */ 163 #define IN_GLOBAL_LOGO 0x2E /* all ports logged out */ 164 #define IN_NO_NEXUS 0x3B /* Nexus not established */ 165 166 /* 167 * Values for the in_task_flags field- should only get one at a time! 168 */ 169 #define TASK_FLAGS_ABORT_TASK (1<<9) 170 #define TASK_FLAGS_CLEAR_TASK_SET (1<<10) 171 #define TASK_FLAGS_TARGET_RESET (1<<13) 172 #define TASK_FLAGS_CLEAR_ACA (1<<14) 173 #define TASK_FLAGS_TERMINATE_TASK (1<<15) 174 175 #ifndef MSG_ABORT_TAG 176 #define MSG_ABORT_TAG 0x06 177 #endif 178 #ifndef MSG_CLEAR_QUEUE 179 #define MSG_CLEAR_QUEUE 0x0e 180 #endif 181 #ifndef MSG_BUS_DEV_RESET 182 #define MSG_BUS_DEV_RESET 0x0b 183 #endif 184 #ifndef MSG_REL_RECOVERY 185 #define MSG_REL_RECOVERY 0x10 186 #endif 187 #ifndef MSG_TERM_IO_PROC 188 #define MSG_TERM_IO_PROC 0x11 189 #endif 190 191 192 /* 193 * Notify Acknowledge Entry structure 194 */ 195 #define NA_RSVDLEN 22 196 typedef struct { 197 isphdr_t na_header; 198 u_int32_t na_reserved; 199 u_int8_t na_lun; /* lun */ 200 u_int8_t na_iid; /* initiator */ 201 u_int8_t na_reserved2; 202 u_int8_t na_tgt; /* target */ 203 u_int32_t na_flags; 204 u_int8_t na_status; 205 u_int8_t na_event; 206 u_int16_t na_seqid; /* sequence id */ 207 u_int16_t na_reserved3[NA_RSVDLEN]; 208 } na_entry_t; 209 210 /* 211 * Value for the na_event field 212 */ 213 #define NA_RST_CLRD 0x80 /* Clear an async event notification */ 214 #define NA_OK 0x01 /* Notify Acknowledge Succeeded */ 215 #define NA_INVALID 0x06 /* Invalid Notify Acknowledge */ 216 217 #define NA2_RSVDLEN 21 218 typedef struct { 219 isphdr_t na_header; 220 u_int32_t na_reserved; 221 u_int8_t na_lun; /* lun */ 222 u_int8_t na_iid; /* initiator */ 223 u_int16_t na_scclun; 224 u_int16_t na_flags; 225 u_int16_t na_reserved2; 226 u_int16_t na_status; 227 u_int16_t na_task_flags; 228 u_int16_t na_seqid; /* sequence id */ 229 u_int16_t na_reserved3[NA2_RSVDLEN]; 230 } na_fcentry_t; 231 #define NAFC_RCOUNT 0x80 /* increment resource count */ 232 #define NAFC_RST_CLRD 0x20 /* Clear LIP Reset */ 233 /* 234 * Accept Target I/O Entry structure 235 */ 236 #define ATIO_CDBLEN 26 237 238 typedef struct { 239 isphdr_t at_header; 240 u_int16_t at_reserved; 241 u_int16_t at_handle; 242 u_int8_t at_lun; /* lun */ 243 u_int8_t at_iid; /* initiator */ 244 u_int8_t at_cdblen; /* cdb length */ 245 u_int8_t at_tgt; /* target */ 246 u_int32_t at_flags; 247 u_int8_t at_status; /* firmware status */ 248 u_int8_t at_scsi_status; /* scsi status */ 249 u_int8_t at_tag_val; /* tag value */ 250 u_int8_t at_tag_type; /* tag type */ 251 u_int8_t at_cdb[ATIO_CDBLEN]; /* received CDB */ 252 u_int8_t at_sense[QLTM_SENSELEN];/* suggested sense data */ 253 } at_entry_t; 254 255 /* 256 * at_flags values 257 */ 258 #define AT_NODISC 0x00008000 /* disconnect disabled */ 259 #define AT_TQAE 0x00000002 /* Tagged Queue Action enabled */ 260 261 /* 262 * at_status values 263 */ 264 #define AT_PATH_INVALID 0x07 /* ATIO sent to firmware for disabled lun */ 265 #define AT_RESET 0x0E /* SCSI Bus Reset Occurred */ 266 #define AT_PHASE_ERROR 0x14 /* Bus phase sequence error */ 267 #define AT_NOCAP 0x16 /* Requested capability not available */ 268 #define AT_BDR_MSG 0x17 /* Bus Device Reset msg received */ 269 #define AT_CDB 0x3D /* CDB received */ 270 271 /* 272 * Macros to create and fetch and test concatenated handle and tag value macros 273 */ 274 275 #define AT_MAKE_TAGID(tid, aep) \ 276 tid = ((aep)->at_handle << 16); \ 277 if ((aep)->at_flags & AT_TQAE) \ 278 (tid) |= ((aep)->at_tag_val + 1) 279 280 #define CT_MAKE_TAGID(tid, ct) \ 281 tid = ((ct)->ct_fwhandle << 16); \ 282 if ((ct)->ct_flags & CT_TQAE) \ 283 (tid) |= ((ct)->ct_tag_val + 1) 284 285 #define AT_HAS_TAG(val) ((val) & 0xffff) 286 #define AT_GET_TAG(val) AT_HAS_TAG(val) - 1 287 #define AT_GET_HANDLE(val) ((val) >> 16) 288 289 /* 290 * Accept Target I/O Entry structure, Type 2 291 */ 292 #define ATIO2_CDBLEN 16 293 294 typedef struct { 295 isphdr_t at_header; 296 u_int32_t at_reserved; 297 u_int8_t at_lun; /* lun or reserved */ 298 u_int8_t at_iid; /* initiator */ 299 u_int16_t at_rxid; /* response ID */ 300 u_int16_t at_flags; 301 u_int16_t at_status; /* firmware status */ 302 u_int8_t at_crn; /* command reference number */ 303 u_int8_t at_taskcodes; 304 u_int8_t at_taskflags; 305 u_int8_t at_execodes; 306 u_int8_t at_cdb[ATIO2_CDBLEN]; /* received CDB */ 307 u_int32_t at_datalen; /* allocated data len */ 308 u_int16_t at_scclun; /* SCC Lun or reserved */ 309 u_int16_t at_wwpn[4]; /* WWPN of initiator */ 310 u_int16_t at_reserved2[6]; 311 u_int16_t at_oxid; 312 } at2_entry_t; 313 314 #define ATIO2_WWPN_OFFSET 0x2A 315 #define ATIO2_OXID_OFFSET 0x3E 316 317 #define ATIO2_TC_ATTR_MASK 0x7 318 #define ATIO2_TC_ATTR_SIMPLEQ 0 319 #define ATIO2_TC_ATTR_HEADOFQ 1 320 #define ATIO2_TC_ATTR_ORDERED 2 321 #define ATIO2_TC_ATTR_ACAQ 4 322 #define ATIO2_TC_ATTR_UNTAGGED 5 323 324 #define ATIO2_EX_WRITE 0x1 325 #define ATIO2_EX_READ 0x2 326 327 /* 328 * Continue Target I/O Entry structure 329 * Request from driver. The response from the 330 * ISP firmware is the same except that the last 18 331 * bytes are overwritten by suggested sense data if 332 * the 'autosense valid' bit is set in the status byte. 333 */ 334 typedef struct { 335 isphdr_t ct_header; 336 u_int16_t ct_reserved; 337 #define ct_syshandle ct_reserved /* we use this */ 338 u_int16_t ct_fwhandle; /* required by f/w */ 339 u_int8_t ct_lun; /* lun */ 340 u_int8_t ct_iid; /* initiator id */ 341 u_int8_t ct_reserved2; 342 u_int8_t ct_tgt; /* our target id */ 343 u_int32_t ct_flags; 344 u_int8_t ct_status; /* isp status */ 345 u_int8_t ct_scsi_status; /* scsi status */ 346 u_int8_t ct_tag_val; /* tag value */ 347 u_int8_t ct_tag_type; /* tag type */ 348 u_int32_t ct_xfrlen; /* transfer length */ 349 u_int32_t ct_resid; /* residual length */ 350 u_int16_t ct_timeout; 351 u_int16_t ct_seg_count; 352 /* 353 * This is so we can share tag name space with 354 * CTIO{2,3,4} with the minimum of pain. 355 */ 356 union { 357 ispds_t ct_a[ISP_RQDSEG]; 358 } _u; 359 #define ct_dataseg _u.ct_a 360 } ct_entry_t; 361 362 /* 363 * For some of the dual port SCSI adapters, port (bus #) is reported 364 * in the MSbit of ct_iid. Bit fields are a bit too awkward here. 365 * 366 * Note that this does not apply to FC adapters at all which can and 367 * do report IIDs between 129 && 255 (these represent devices that have 368 * logged in across a SCSI fabric). 369 */ 370 #define GET_IID_VAL(x) (x & 0x3f) 371 #define GET_BUS_VAL(x) ((x >> 7) & 0x1) 372 #define SET_IID_VAL(y, x) y = ((y & ~0x3f) | (x & 0x3f)) 373 #define SET_BUS_VAL(y, x) y = ((y & 0x3f) | ((x & 0x1) << 7)) 374 375 /* 376 * ct_flags values 377 */ 378 #define CT_TQAE 0x00000002 /* bit 1, Tagged Queue Action enable */ 379 #define CT_DATA_IN 0x00000040 /* bits 6&7, Data direction */ 380 #define CT_DATA_OUT 0x00000080 /* bits 6&7, Data direction */ 381 #define CT_NO_DATA 0x000000C0 /* bits 6&7, Data direction */ 382 #define CT_CCINCR 0x00000100 /* bit 8, autoincrement atio count */ 383 #define CT_DATAMASK 0x000000C0 /* bits 6&7, Data direction */ 384 #define CT_INISYNCWIDE 0x00004000 /* bit 14, Do Sync/Wide Negotiation */ 385 #define CT_NODISC 0x00008000 /* bit 15, Disconnects disabled */ 386 #define CT_DSDP 0x01000000 /* bit 24, Disable Save Data Pointers */ 387 #define CT_SENDRDP 0x04000000 /* bit 26, Send Restore Pointers msg */ 388 #define CT_SENDSTATUS 0x80000000 /* bit 31, Send SCSI status byte */ 389 390 /* 391 * ct_status values 392 * - set by the firmware when it returns the CTIO 393 */ 394 #define CT_OK 0x01 /* completed without error */ 395 #define CT_ABORTED 0x02 /* aborted by host */ 396 #define CT_ERR 0x04 /* see sense data for error */ 397 #define CT_INVAL 0x06 /* request for disabled lun */ 398 #define CT_NOPATH 0x07 /* invalid ITL nexus */ 399 #define CT_INVRXID 0x08 /* (FC only) Invalid RX_ID */ 400 #define CT_DATA_OVER 0x09 /* (FC only) Data Overrun */ 401 #define CT_RSELTMO 0x0A /* reselection timeout after 2 tries */ 402 #define CT_TIMEOUT 0x0B /* timed out */ 403 #define CT_RESET 0x0E /* SCSI Bus Reset occurred */ 404 #define CT_PARITY 0x0F /* Uncorrectable Parity Error */ 405 #define CT_BUS_ERROR 0x10 /* (FC Only) DMA PCI Error */ 406 #define CT_PANIC 0x13 /* Unrecoverable Error */ 407 #define CT_PHASE_ERROR 0x14 /* Bus phase sequence error */ 408 #define CT_BDR_MSG 0x17 /* Bus Device Reset msg received */ 409 #define CT_DATA_UNDER 0x15 /* (FC only) Data Underrun */ 410 #define CT_TERMINATED 0x19 /* due to Terminate Transfer mbox cmd */ 411 #define CT_PORTNOTAVAIL 0x28 /* port not available */ 412 #define CT_LOGOUT 0x29 /* port logout */ 413 #define CT_PORTCHANGED 0x2A /* port changed */ 414 #define CT_IDE 0x33 /* Initiator Detected Error */ 415 #define CT_NOACK 0x35 /* Outstanding Immed. Notify. entry */ 416 417 /* 418 * When the firmware returns a CTIO entry, it may overwrite the last 419 * part of the structure with sense data. This starts at offset 0x2E 420 * into the entry, which is in the middle of ct_dataseg[1]. Rather 421 * than define a new struct for this, I'm just using the sense data 422 * offset. 423 */ 424 #define CTIO_SENSE_OFFSET 0x2E 425 426 /* 427 * Entry length in u_longs. All entries are the same size so 428 * any one will do as the numerator. 429 */ 430 #define UINT32_ENTRY_SIZE (sizeof(at_entry_t)/sizeof(u_int32_t)) 431 432 /* 433 * QLA2100 CTIO (type 2) entry 434 */ 435 #define MAXRESPLEN 26 436 typedef struct { 437 isphdr_t ct_header; 438 u_int16_t ct_reserved; 439 u_int16_t ct_fwhandle; /* just to match CTIO */ 440 u_int8_t ct_lun; /* lun */ 441 u_int8_t ct_iid; /* initiator id */ 442 u_int16_t ct_rxid; /* response ID */ 443 u_int16_t ct_flags; 444 u_int16_t ct_status; /* isp status */ 445 u_int16_t ct_timeout; 446 u_int16_t ct_seg_count; 447 u_int32_t ct_reloff; /* relative offset */ 448 int32_t ct_resid; /* residual length */ 449 union { 450 /* 451 * The three different modes that the target driver 452 * can set the CTIO{2,3,4} up as. 453 * 454 * The first is for sending FCP_DATA_IUs as well as 455 * (optionally) sending a terminal SCSI status FCP_RSP_IU. 456 * 457 * The second is for sending SCSI sense data in an FCP_RSP_IU. 458 * Note that no FCP_DATA_IUs will be sent. 459 * 460 * The third is for sending FCP_RSP_IUs as built specifically 461 * in system memory as located by the isp_dataseg. 462 */ 463 struct { 464 u_int32_t _reserved; 465 u_int16_t _reserved2; 466 u_int16_t ct_scsi_status; 467 u_int32_t ct_xfrlen; 468 union { 469 ispds_t ct_a[ISP_RQDSEG_T2]; /* CTIO2 */ 470 ispds64_t ct_b[ISP_RQDSEG_T3]; /* CTIO3 */ 471 ispdslist_t ct_c; /* CTIO4 */ 472 } _u; 473 #define ct_dataseg _u.ct_a 474 #define ct_dataseg64 _u.ct_b 475 #define ct_dslist _u.ct_c 476 } m0; 477 struct { 478 u_int16_t _reserved; 479 u_int16_t _reserved2; 480 u_int16_t ct_senselen; 481 u_int16_t ct_scsi_status; 482 u_int16_t ct_resplen; 483 u_int8_t ct_resp[MAXRESPLEN]; 484 } m1; 485 struct { 486 u_int32_t _reserved; 487 u_int16_t _reserved2; 488 u_int16_t _reserved3; 489 u_int32_t ct_datalen; 490 ispds_t ct_fcp_rsp_iudata; 491 } m2; 492 } rsp; 493 } ct2_entry_t; 494 495 /* 496 * ct_flags values for CTIO2 497 */ 498 #define CT2_FLAG_MMASK 0x0003 499 #define CT2_FLAG_MODE0 0x0000 500 #define CT2_FLAG_MODE1 0x0001 501 #define CT2_FLAG_MODE2 0x0002 502 #define CT2_DATA_IN CT_DATA_IN 503 #define CT2_DATA_OUT CT_DATA_OUT 504 #define CT2_NO_DATA CT_NO_DATA 505 #define CT2_DATAMASK CT_DATAMASK 506 #define CT2_CCINCR 0x0100 507 #define CT2_FASTPOST 0x0200 508 #define CT2_TERMINATE 0x4000 509 #define CT2_SENDSTATUS 0x8000 510 511 /* 512 * ct_status values are (mostly) the same as that for ct_entry. 513 */ 514 515 /* 516 * ct_scsi_status values- the low 8 bits are the normal SCSI status 517 * we know and love. The upper 8 bits are validity markers for FCP_RSP_IU 518 * fields. 519 */ 520 #define CT2_RSPLEN_VALID 0x0100 521 #define CT2_SNSLEN_VALID 0x0200 522 #define CT2_DATA_OVER 0x0400 523 #define CT2_DATA_UNDER 0x0800 524 525 /* 526 * Debug macros 527 */ 528 529 #define ISP_TDQE(isp, msg, idx, arg) \ 530 if (isp->isp_dblev & ISP_LOGTDEBUG2) isp_print_qentry(isp, msg, idx, arg) 531 532 #ifdef ISP_TARGET_FUNCTIONS 533 /* 534 * The functions below are for the publicly available 535 * target mode functions that are internal to the Qlogic driver. 536 */ 537 538 /* 539 * This function handles new response queue entry appropriate for target mode. 540 */ 541 int isp_target_notify(struct ispsoftc *, void *, u_int16_t *); 542 543 /* 544 * Enable/Disable/Modify a logical unit. 545 * (softc, cmd, bus, tgt, lun, cmd_cnt, inotify_cnt, opaque) 546 */ 547 #define DFLT_CMND_CNT 0xfe /* unmonitored */ 548 #define DFLT_INOT_CNT 16 549 int isp_lun_cmd(struct ispsoftc *, int, int, int, int, int, int, u_int32_t); 550 551 /* 552 * General request queue 'put' routine for target mode entries. 553 */ 554 int isp_target_put_entry(struct ispsoftc *isp, void *); 555 556 /* 557 * General routine to put back an ATIO entry- 558 * used for replenishing f/w resource counts. 559 * The argument is a pointer to a source ATIO 560 * or ATIO2. 561 */ 562 int isp_target_put_atio(struct ispsoftc *, void *); 563 564 /* 565 * General routine to send a final CTIO for a command- used mostly for 566 * local responses. 567 */ 568 int isp_endcmd(struct ispsoftc *, void *, u_int32_t, u_int16_t); 569 #define ECMD_SVALID 0x100 570 571 /* 572 * Handle an asynchronous event 573 * 574 * Return nonzero if the interrupt that generated this event has been dismissed. 575 */ 576 577 int isp_target_async(struct ispsoftc *, int, int); 578 #endif 579 #endif /* _ISP_TARGET_H */ 580
Indexes created Fri Sep 26 20:09:58 GMT 2025