ispreg.h revision 1.14
1 /* $NetBSD: ispreg.h,v 1.14 1999/03/26 22:39:45 mjacob Exp $ */ 2 /* release_03_25_99 */ 3 /* 4 * Machine Independent (well, as best as possible) register 5 * definitions for Qlogic ISP SCSI adapters. 6 * 7 * Copyright (c) 1997, 1998, 1999 by Matthew Jacob 8 * NASA/Ames Research Center 9 * All rights reserved. 10 * 11 * Redistribution and use in source and binary forms, with or without 12 * modification, are permitted provided that the following conditions 13 * are met: 14 * 1. Redistributions of source code must retain the above copyright 15 * notice immediately at the beginning of the file, without modification, 16 * this list of conditions, and the following disclaimer. 17 * 2. Redistributions in binary form must reproduce the above copyright 18 * notice, this list of conditions and the following disclaimer in the 19 * documentation and/or other materials provided with the distribution. 20 * 3. The name of the author may not be used to endorse or promote products 21 * derived from this software without specific prior written permission. 22 * 23 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 24 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 25 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 26 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR 27 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 28 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 29 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 30 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 31 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 32 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 33 * SUCH DAMAGE. 34 */ 35 #ifndef _ISPREG_H 36 #define _ISPREG_H 37 38 /* 39 * Hardware definitions for the Qlogic ISP registers. 40 */ 41 42 /* 43 * This defines types of access to various registers. 44 * 45 * R: Read Only 46 * W: Write Only 47 * RW: Read/Write 48 * 49 * R*, W*, RW*: Read Only, Write Only, Read/Write, but only 50 * if RISC processor in ISP is paused. 51 */ 52 53 /* 54 * Offsets for various register blocks. 55 * 56 * Sad but true, different architectures have different offsets. 57 */ 58 59 #define BIU_REGS_OFF 0x00 60 61 #define PCI_MBOX_REGS_OFF 0x70 62 #define PCI_MBOX_REGS2100_OFF 0x10 63 #define SBUS_MBOX_REGS_OFF 0x80 64 65 #define PCI_SXP_REGS_OFF 0x80 66 #define SBUS_SXP_REGS_OFF 0x200 67 68 #define PCI_RISC_REGS_OFF 0x80 69 #define SBUS_RISC_REGS_OFF 0x400 70 71 /* Bless me! Chip designers have putzed it again! */ 72 #define ISP1080_DMA_REGS_OFF 0x60 73 #define DMA_REGS_OFF 0x00 /* same as BIU block */ 74 75 /* 76 * NB: The *_BLOCK definitions have no specific hardware meaning. 77 * They serve simply to note to the MD layer which block of 78 * registers offsets are being accessed. 79 */ 80 #define _NREG_BLKS 5 81 #define _BLK_REG_SHFT 13 82 #define _BLK_REG_MASK (7 << _BLK_REG_SHFT) 83 #define BIU_BLOCK (0 << _BLK_REG_SHFT) 84 #define MBOX_BLOCK (1 << _BLK_REG_SHFT) 85 #define SXP_BLOCK (2 << _BLK_REG_SHFT) 86 #define RISC_BLOCK (3 << _BLK_REG_SHFT) 87 #define DMA_BLOCK (4 << _BLK_REG_SHFT) 88 89 /* 90 * Bus Interface Block Register Offsets 91 */ 92 93 #define BIU_ID_LO BIU_BLOCK+0x0 /* R : Bus ID, Low */ 94 #define BIU2100_FLASH_ADDR BIU_BLOCK+0x0 95 #define BIU_ID_HI BIU_BLOCK+0x2 /* R : Bus ID, High */ 96 #define BIU2100_FLASH_DATA BIU_BLOCK+0x2 97 #define BIU_CONF0 BIU_BLOCK+0x4 /* R : Bus Configuration #0 */ 98 #define BIU_CONF1 BIU_BLOCK+0x6 /* R : Bus Configuration #1 */ 99 #define BIU2100_CSR BIU_BLOCK+0x6 100 #define BIU_ICR BIU_BLOCK+0x8 /* RW : Bus Interface Ctrl */ 101 #define BIU_ISR BIU_BLOCK+0xA /* R : Bus Interface Status */ 102 #define BIU_SEMA BIU_BLOCK+0xC /* RW : Bus Semaphore */ 103 #define BIU_NVRAM BIU_BLOCK+0xE /* RW : Bus NVRAM */ 104 #define DFIFO_COMMAND BIU_BLOCK+0x60 /* RW : Command FIFO Port */ 105 #define RDMA2100_CONTROL DFIFO_COMMAND 106 #define DFIFO_DATA BIU_BLOCK+0x62 /* RW : Data FIFO Port */ 107 108 /* 109 * Putzed DMA register layouts. 110 */ 111 #define CDMA_CONF DMA_BLOCK+0x20 /* RW*: DMA Configuration */ 112 #define CDMA2100_CONTROL CDMA_CONF 113 #define CDMA_CONTROL DMA_BLOCK+0x22 /* RW*: DMA Control */ 114 #define CDMA_STATUS DMA_BLOCK+0x24 /* R : DMA Status */ 115 #define CDMA_FIFO_STS DMA_BLOCK+0x26 /* R : DMA FIFO Status */ 116 #define CDMA_COUNT DMA_BLOCK+0x28 /* RW*: DMA Transfer Count */ 117 #define CDMA_ADDR0 DMA_BLOCK+0x2C /* RW*: DMA Address, Word 0 */ 118 #define CDMA_ADDR1 DMA_BLOCK+0x2E /* RW*: DMA Address, Word 1 */ 119 #define CDMA_ADDR2 DMA_BLOCK+0x30 /* RW*: DMA Address, Word 2 */ 120 #define CDMA_ADDR3 DMA_BLOCK+0x32 /* RW*: DMA Address, Word 3 */ 121 122 #define DDMA_CONF DMA_BLOCK+0x40 /* RW*: DMA Configuration */ 123 #define TDMA2100_CONTROL DDMA_CONF 124 #define DDMA_CONTROL DMA_BLOCK+0x42 /* RW*: DMA Control */ 125 #define DDMA_STATUS DMA_BLOCK+0x44 /* R : DMA Status */ 126 #define DDMA_FIFO_STS DMA_BLOCK+0x46 /* R : DMA FIFO Status */ 127 #define DDMA_COUNT_LO DMA_BLOCK+0x48 /* RW*: DMA Xfer Count, Low */ 128 #define DDMA_COUNT_HI DMA_BLOCK+0x4A /* RW*: DMA Xfer Count, High */ 129 #define DDMA_ADDR0 DMA_BLOCK+0x4C /* RW*: DMA Address, Word 0 */ 130 #define DDMA_ADDR1 DMA_BLOCK+0x4E /* RW*: DMA Address, Word 1 */ 131 /* these are for the 1040A cards */ 132 #define DDMA_ADDR2 DMA_BLOCK+0x50 /* RW*: DMA Address, Word 2 */ 133 #define DDMA_ADDR3 DMA_BLOCK+0x52 /* RW*: DMA Address, Word 3 */ 134 135 136 /* 137 * Bus Interface Block Register Definitions 138 */ 139 /* BUS CONFIGURATION REGISTER #0 */ 140 #define BIU_CONF0_HW_MASK 0x000F /* Hardware revision mask */ 141 /* BUS CONFIGURATION REGISTER #1 */ 142 143 #define BIU_SBUS_CONF1_PARITY 0x0100 /* Enable parity checking */ 144 #define BIU_SBUS_CONF1_FCODE_MASK 0x00F0 /* Fcode cycle mask */ 145 146 #define BIU_PCI_CONF1_FIFO_128 0x0040 /* 128 bytes FIFO threshold */ 147 #define BIU_PCI_CONF1_FIFO_64 0x0030 /* 64 bytes FIFO threshold */ 148 #define BIU_PCI_CONF1_FIFO_32 0x0020 /* 32 bytes FIFO threshold */ 149 #define BIU_PCI_CONF1_FIFO_16 0x0010 /* 16 bytes FIFO threshold */ 150 #define BIU_BURST_ENABLE 0x0004 /* Global enable Bus bursts */ 151 #define BIU_SBUS_CONF1_FIFO_64 0x0003 /* 64 bytes FIFO threshold */ 152 #define BIU_SBUS_CONF1_FIFO_32 0x0002 /* 32 bytes FIFO threshold */ 153 #define BIU_SBUS_CONF1_FIFO_16 0x0001 /* 16 bytes FIFO threshold */ 154 #define BIU_SBUS_CONF1_FIFO_8 0x0000 /* 8 bytes FIFO threshold */ 155 #define BIU_SBUS_CONF1_BURST8 0x0008 /* Enable 8-byte bursts */ 156 #define BIU_PCI_CONF1_SXP 0x0008 /* SXP register select */ 157 158 #define BIU_PCI1080_CONF1_SXP 0x0100 /* SXP bank select */ 159 #define BIU_PCI1080_CONF1_DMA 0x0300 /* DMA bank select */ 160 161 /* ISP2100 Bus Control/Status Register */ 162 163 #define BIU2100_ICSR_REGBSEL 0x30 /* RW: register bank select */ 164 #define BIU2100_RISC_REGS (0 << 4) /* RISC Regs */ 165 #define BIU2100_FB_REGS (1 << 4) /* FrameBuffer Regs */ 166 #define BIU2100_FPM0_REGS (2 << 4) /* FPM 0 Regs */ 167 #define BIU2100_FPM1_REGS (3 << 4) /* FPM 1 Regs */ 168 #define BIU2100_PCI64 0x04 /* R: 64 Bit PCI slot */ 169 #define BIU2100_FLASH_ENABLE 0x02 /* RW: Enable Flash RAM */ 170 #define BIU2100_SOFT_RESET 0x01 171 /* SOFT RESET FOR ISP2100 is same bit, but in this register, not ICR */ 172 173 174 /* BUS CONTROL REGISTER */ 175 #define BIU_ICR_ENABLE_DMA_INT 0x0020 /* Enable DMA interrupts */ 176 #define BIU_ICR_ENABLE_CDMA_INT 0x0010 /* Enable CDMA interrupts */ 177 #define BIU_ICR_ENABLE_SXP_INT 0x0008 /* Enable SXP interrupts */ 178 #define BIU_ICR_ENABLE_RISC_INT 0x0004 /* Enable Risc interrupts */ 179 #define BIU_ICR_ENABLE_ALL_INTS 0x0002 /* Global enable all inter */ 180 #define BIU_ICR_SOFT_RESET 0x0001 /* Soft Reset of ISP */ 181 182 #define BIU2100_ICR_ENABLE_ALL_INTS 0x8000 183 #define BIU2100_ICR_ENA_FPM_INT 0x0020 184 #define BIU2100_ICR_ENA_FB_INT 0x0010 185 #define BIU2100_ICR_ENA_RISC_INT 0x0008 186 #define BIU2100_ICR_ENA_CDMA_INT 0x0004 187 #define BIU2100_ICR_ENABLE_RXDMA_INT 0x0002 188 #define BIU2100_ICR_ENABLE_TXDMA_INT 0x0001 189 #define BIU2100_ICR_DISABLE_ALL_INTS 0x0000 190 191 #define ENABLE_INTS(isp) (isp->isp_type & ISP_HA_SCSI)? \ 192 ISP_WRITE(isp, BIU_ICR, BIU_ICR_ENABLE_RISC_INT | BIU_ICR_ENABLE_ALL_INTS) : \ 193 ISP_WRITE(isp, BIU_ICR, BIU2100_ICR_ENA_RISC_INT | BIU2100_ICR_ENABLE_ALL_INTS) 194 195 #define INTS_ENABLED(isp) ((isp->isp_type & ISP_HA_SCSI)? \ 196 (ISP_READ(isp, BIU_ICR) & (BIU_ICR_ENABLE_RISC_INT|BIU_ICR_ENABLE_ALL_INTS)) :\ 197 (ISP_READ(isp, BIU_ICR) & \ 198 (BIU2100_ICR_ENA_RISC_INT|BIU2100_ICR_ENABLE_ALL_INTS))) 199 200 #define DISABLE_INTS(isp) ISP_WRITE(isp, BIU_ICR, 0) 201 202 /* BUS STATUS REGISTER */ 203 #define BIU_ISR_DMA_INT 0x0020 /* DMA interrupt pending */ 204 #define BIU_ISR_CDMA_INT 0x0010 /* CDMA interrupt pending */ 205 #define BIU_ISR_SXP_INT 0x0008 /* SXP interrupt pending */ 206 #define BIU_ISR_RISC_INT 0x0004 /* Risc interrupt pending */ 207 #define BIU_ISR_IPEND 0x0002 /* Global interrupt pending */ 208 209 #define BIU2100_ISR_INT_PENDING 0x8000 /* Global interrupt pending */ 210 #define BIU2100_ISR_FPM_INT 0x0020 /* FPM interrupt pending */ 211 #define BIU2100_ISR_FB_INT 0x0010 /* FB interrupt pending */ 212 #define BIU2100_ISR_RISC_INT 0x0008 /* Risc interrupt pending */ 213 #define BIU2100_ISR_CDMA_INT 0x0004 /* CDMA interrupt pending */ 214 #define BIU2100_ISR_RXDMA_INT_PENDING 0x0002 /* Global interrupt pending */ 215 #define BIU2100_ISR_TXDMA_INT_PENDING 0x0001 /* Global interrupt pending */ 216 217 218 /* BUS SEMAPHORE REGISTER */ 219 #define BIU_SEMA_STATUS 0x0002 /* Semaphore Status Bit */ 220 #define BIU_SEMA_LOCK 0x0001 /* Semaphore Lock Bit */ 221 222 /* NVRAM SEMAPHORE REGISTER */ 223 #define BIU_NVRAM_CLOCK 0x0001 224 #define BIU_NVRAM_SELECT 0x0002 225 #define BIU_NVRAM_DATAOUT 0x0004 226 #define BIU_NVRAM_DATAIN 0x0008 227 #define ISP_NVRAM_READ 6 228 229 /* COMNMAND && DATA DMA CONFIGURATION REGISTER */ 230 #define DMA_ENABLE_SXP_DMA 0x0008 /* Enable SXP to DMA Data */ 231 #define DMA_ENABLE_INTS 0x0004 /* Enable interrupts to RISC */ 232 #define DMA_ENABLE_BURST 0x0002 /* Enable Bus burst trans */ 233 #define DMA_DMA_DIRECTION 0x0001 /* 234 * Set DMA direction: 235 * 0 - DMA FIFO to host 236 * 1 - Host to DMA FIFO 237 */ 238 239 /* COMMAND && DATA DMA CONTROL REGISTER */ 240 #define DMA_CNTRL_SUSPEND_CHAN 0x0010 /* Suspend DMA transfer */ 241 #define DMA_CNTRL_CLEAR_CHAN 0x0008 /* 242 * Clear FIFO and DMA Channel, 243 * reset DMA registers 244 */ 245 #define DMA_CNTRL_CLEAR_FIFO 0x0004 /* Clear DMA FIFO */ 246 #define DMA_CNTRL_RESET_INT 0x0002 /* Clear DMA interrupt */ 247 #define DMA_CNTRL_STROBE 0x0001 /* Start DMA transfer */ 248 249 /* 250 * Variants of same for 2100 251 */ 252 #define DMA_CNTRL2100_CLEAR_CHAN 0x0004 253 #define DMA_CNTRL2100_RESET_INT 0x0002 254 255 256 257 /* DMA STATUS REGISTER */ 258 #define DMA_SBUS_STATUS_PIPE_MASK 0x00C0 /* DMA Pipeline status mask */ 259 #define DMA_SBUS_STATUS_CHAN_MASK 0x0030 /* Channel status mask */ 260 #define DMA_SBUS_STATUS_BUS_PARITY 0x0008 /* Parity Error on bus */ 261 #define DMA_SBUS_STATUS_BUS_ERR 0x0004 /* Error Detected on bus */ 262 #define DMA_SBUS_STATUS_TERM_COUNT 0x0002 /* DMA Transfer Completed */ 263 #define DMA_SBUS_STATUS_INTERRUPT 0x0001 /* Enable DMA channel inter */ 264 265 #define DMA_PCI_STATUS_INTERRUPT 0x8000 /* Enable DMA channel inter */ 266 #define DMA_PCI_STATUS_RETRY_STAT 0x4000 /* Retry status */ 267 #define DMA_PCI_STATUS_CHAN_MASK 0x3000 /* Channel status mask */ 268 #define DMA_PCI_STATUS_FIFO_OVR 0x0100 /* DMA FIFO overrun cond */ 269 #define DMA_PCI_STATUS_FIFO_UDR 0x0080 /* DMA FIFO underrun cond */ 270 #define DMA_PCI_STATUS_BUS_ERR 0x0040 /* Error Detected on bus */ 271 #define DMA_PCI_STATUS_BUS_PARITY 0x0020 /* Parity Error on bus */ 272 #define DMA_PCI_STATUS_CLR_PEND 0x0010 /* DMA clear pending */ 273 #define DMA_PCI_STATUS_TERM_COUNT 0x0008 /* DMA Transfer Completed */ 274 #define DMA_PCI_STATUS_DMA_SUSP 0x0004 /* DMA suspended */ 275 #define DMA_PCI_STATUS_PIPE_MASK 0x0003 /* DMA Pipeline status mask */ 276 277 /* DMA Status Register, pipeline status bits */ 278 #define DMA_SBUS_PIPE_FULL 0x00C0 /* Both pipeline stages full */ 279 #define DMA_SBUS_PIPE_OVERRUN 0x0080 /* Pipeline overrun */ 280 #define DMA_SBUS_PIPE_STAGE1 0x0040 /* 281 * Pipeline stage 1 Loaded, 282 * stage 2 empty 283 */ 284 #define DMA_PCI_PIPE_FULL 0x0003 /* Both pipeline stages full */ 285 #define DMA_PCI_PIPE_OVERRUN 0x0002 /* Pipeline overrun */ 286 #define DMA_PCI_PIPE_STAGE1 0x0001 /* 287 * Pipeline stage 1 Loaded, 288 * stage 2 empty 289 */ 290 #define DMA_PIPE_EMPTY 0x0000 /* All pipeline stages empty */ 291 292 /* DMA Status Register, channel status bits */ 293 #define DMA_SBUS_CHAN_SUSPEND 0x0030 /* Channel error or suspended */ 294 #define DMA_SBUS_CHAN_TRANSFER 0x0020 /* Chan transfer in progress */ 295 #define DMA_SBUS_CHAN_ACTIVE 0x0010 /* Chan trans to host active */ 296 #define DMA_PCI_CHAN_TRANSFER 0x3000 /* Chan transfer in progress */ 297 #define DMA_PCI_CHAN_SUSPEND 0x2000 /* Channel error or suspended */ 298 #define DMA_PCI_CHAN_ACTIVE 0x1000 /* Chan trans to host active */ 299 #define ISP_DMA_CHAN_IDLE 0x0000 /* Chan idle (normal comp) */ 300 301 302 /* DMA FIFO STATUS REGISTER */ 303 #define DMA_FIFO_STATUS_OVERRUN 0x0200 /* FIFO Overrun Condition */ 304 #define DMA_FIFO_STATUS_UNDERRUN 0x0100 /* FIFO Underrun Condition */ 305 #define DMA_FIFO_SBUS_COUNT_MASK 0x007F /* FIFO Byte count mask */ 306 #define DMA_FIFO_PCI_COUNT_MASK 0x00FF /* FIFO Byte count mask */ 307 308 /* 309 * Mailbox Block Register Offsets 310 */ 311 312 #define INMAILBOX0 MBOX_BLOCK+0x0 313 #define INMAILBOX1 MBOX_BLOCK+0x2 314 #define INMAILBOX2 MBOX_BLOCK+0x4 315 #define INMAILBOX3 MBOX_BLOCK+0x6 316 #define INMAILBOX4 MBOX_BLOCK+0x8 317 #define INMAILBOX5 MBOX_BLOCK+0xA 318 #define INMAILBOX6 MBOX_BLOCK+0xC 319 #define INMAILBOX7 MBOX_BLOCK+0xE 320 321 #define OUTMAILBOX0 MBOX_BLOCK+0x0 322 #define OUTMAILBOX1 MBOX_BLOCK+0x2 323 #define OUTMAILBOX2 MBOX_BLOCK+0x4 324 #define OUTMAILBOX3 MBOX_BLOCK+0x6 325 #define OUTMAILBOX4 MBOX_BLOCK+0x8 326 #define OUTMAILBOX5 MBOX_BLOCK+0xA 327 #define OUTMAILBOX6 MBOX_BLOCK+0xC 328 #define OUTMAILBOX7 MBOX_BLOCK+0xE 329 330 #define OMBOX_OFFN(n) (MBOX_BLOCK + (n * 2)) 331 #define NMBOX(isp) \ 332 (((((isp)->isp_type & ISP_HA_SCSI) >= ISP_HA_SCSI_1040A) || \ 333 ((isp)->isp_type & ISP_HA_FC))? 8 : 6) 334 335 /* 336 * SXP Block Register Offsets 337 */ 338 #define SXP_PART_ID SXP_BLOCK+0x0 /* R : Part ID Code */ 339 #define SXP_CONFIG1 SXP_BLOCK+0x2 /* RW*: Configuration Reg #1 */ 340 #define SXP_CONFIG2 SXP_BLOCK+0x4 /* RW*: Configuration Reg #2 */ 341 #define SXP_CONFIG3 SXP_BLOCK+0x6 /* RW*: Configuration Reg #2 */ 342 #define SXP_INSTRUCTION SXP_BLOCK+0xC /* RW*: Instruction Pointer */ 343 #define SXP_RETURN_ADDR SXP_BLOCK+0x10 /* RW*: Return Address */ 344 #define SXP_COMMAND SXP_BLOCK+0x14 /* RW*: Command */ 345 #define SXP_INTERRUPT SXP_BLOCK+0x18 /* R : Interrupt */ 346 #define SXP_SEQUENCE SXP_BLOCK+0x1C /* RW*: Sequence */ 347 #define SXP_GROSS_ERR SXP_BLOCK+0x1E /* R : Gross Error */ 348 #define SXP_EXCEPTION SXP_BLOCK+0x20 /* RW*: Exception Enable */ 349 #define SXP_OVERRIDE SXP_BLOCK+0x24 /* RW*: Override */ 350 #define SXP_LITERAL_BASE SXP_BLOCK+0x28 /* RW*: Literal Base */ 351 #define SXP_USER_FLAGS SXP_BLOCK+0x2C /* RW*: User Flags */ 352 #define SXP_USER_EXCEPT SXP_BLOCK+0x30 /* RW*: User Exception */ 353 #define SXP_BREAKPOINT SXP_BLOCK+0x34 /* RW*: Breakpoint */ 354 #define SXP_SCSI_ID SXP_BLOCK+0x40 /* RW*: SCSI ID */ 355 #define SXP_DEV_CONFIG1 SXP_BLOCK+0x42 /* RW*: Device Config Reg #1 */ 356 #define SXP_DEV_CONFIG2 SXP_BLOCK+0x44 /* RW*: Device Config Reg #2 */ 357 #define SXP_PHASE_POINTER SXP_BLOCK+0x48 /* RW*: SCSI Phase Pointer */ 358 #define SXP_BUF_POINTER SXP_BLOCK+0x4C /* RW*: SCSI Buffer Pointer */ 359 #define SXP_BUF_COUNTER SXP_BLOCK+0x50 /* RW*: SCSI Buffer Counter */ 360 #define SXP_BUFFER SXP_BLOCK+0x52 /* RW*: SCSI Buffer */ 361 #define SXP_BUF_BYTE SXP_BLOCK+0x54 /* RW*: SCSI Buffer Byte */ 362 #define SXP_BUF_WORD SXP_BLOCK+0x56 /* RW*: SCSI Buffer Word */ 363 #define SXP_BUF_WORD_TRAN SXP_BLOCK+0x58 /* RW*: SCSI Buffer Wd xlate */ 364 #define SXP_FIFO SXP_BLOCK+0x5A /* RW*: SCSI FIFO */ 365 #define SXP_FIFO_STATUS SXP_BLOCK+0x5C /* RW*: SCSI FIFO Status */ 366 #define SXP_FIFO_TOP SXP_BLOCK+0x5E /* RW*: SCSI FIFO Top Resid */ 367 #define SXP_FIFO_BOTTOM SXP_BLOCK+0x60 /* RW*: SCSI FIFO Bot Resid */ 368 #define SXP_TRAN_REG SXP_BLOCK+0x64 /* RW*: SCSI Transferr Reg */ 369 #define SXP_TRAN_COUNT_LO SXP_BLOCK+0x68 /* RW*: SCSI Trans Count */ 370 #define SXP_TRAN_COUNT_HI SXP_BLOCK+0x6A /* RW*: SCSI Trans Count */ 371 #define SXP_TRAN_COUNTER_LO SXP_BLOCK+0x6C /* RW*: SCSI Trans Counter */ 372 #define SXP_TRAN_COUNTER_HI SXP_BLOCK+0x6E /* RW*: SCSI Trans Counter */ 373 #define SXP_ARB_DATA SXP_BLOCK+0x70 /* R : SCSI Arb Data */ 374 #define SXP_PINS_CONTROL SXP_BLOCK+0x72 /* RW*: SCSI Control Pins */ 375 #define SXP_PINS_DATA SXP_BLOCK+0x74 /* RW*: SCSI Data Pins */ 376 #define SXP_PINS_DIFF SXP_BLOCK+0x76 /* RW*: SCSI Diff Pins */ 377 378 379 /* SXP CONF1 REGISTER */ 380 #define SXP_CONF1_ASYNCH_SETUP 0xF000 /* Asynchronous setup time */ 381 #define SXP_CONF1_SELECTION_UNIT 0x0000 /* Selection time unit */ 382 #define SXP_CONF1_SELECTION_TIMEOUT 0x0600 /* Selection timeout */ 383 #define SXP_CONF1_CLOCK_FACTOR 0x00E0 /* Clock factor */ 384 #define SXP_CONF1_SCSI_ID 0x000F /* SCSI id */ 385 386 /* SXP CONF2 REGISTER */ 387 #define SXP_CONF2_DISABLE_FILTER 0x0040 /* Disable SCSI rec filters */ 388 #define SXP_CONF2_REQ_ACK_PULLUPS 0x0020 /* Enable req/ack pullups */ 389 #define SXP_CONF2_DATA_PULLUPS 0x0010 /* Enable data pullups */ 390 #define SXP_CONF2_CONFIG_AUTOLOAD 0x0008 /* Enable dev conf auto-load */ 391 #define SXP_CONF2_RESELECT 0x0002 /* Enable reselection */ 392 #define SXP_CONF2_SELECT 0x0001 /* Enable selection */ 393 394 /* SXP INTERRUPT REGISTER */ 395 #define SXP_INT_PARITY_ERR 0x8000 /* Parity error detected */ 396 #define SXP_INT_GROSS_ERR 0x4000 /* Gross error detected */ 397 #define SXP_INT_FUNCTION_ABORT 0x2000 /* Last cmd aborted */ 398 #define SXP_INT_CONDITION_FAILED 0x1000 /* Last cond failed test */ 399 #define SXP_INT_FIFO_EMPTY 0x0800 /* SCSI FIFO is empty */ 400 #define SXP_INT_BUF_COUNTER_ZERO 0x0400 /* SCSI buf count == zero */ 401 #define SXP_INT_XFER_ZERO 0x0200 /* SCSI trans count == zero */ 402 #define SXP_INT_INT_PENDING 0x0080 /* SXP interrupt pending */ 403 #define SXP_INT_CMD_RUNNING 0x0040 /* SXP is running a command */ 404 #define SXP_INT_INT_RETURN_CODE 0x000F /* Interrupt return code */ 405 406 407 /* SXP GROSS ERROR REGISTER */ 408 #define SXP_GROSS_OFFSET_RESID 0x0040 /* Req/Ack offset not zero */ 409 #define SXP_GROSS_OFFSET_UNDERFLOW 0x0020 /* Req/Ack offset underflow */ 410 #define SXP_GROSS_OFFSET_OVERFLOW 0x0010 /* Req/Ack offset overflow */ 411 #define SXP_GROSS_FIFO_UNDERFLOW 0x0008 /* SCSI FIFO underflow */ 412 #define SXP_GROSS_FIFO_OVERFLOW 0x0004 /* SCSI FIFO overflow */ 413 #define SXP_GROSS_WRITE_ERR 0x0002 /* SXP and RISC wrote to reg */ 414 #define SXP_GROSS_ILLEGAL_INST 0x0001 /* Bad inst loaded into SXP */ 415 416 /* SXP EXCEPTION REGISTER */ 417 #define SXP_EXCEPT_USER_0 0x8000 /* Enable user exception #0 */ 418 #define SXP_EXCEPT_USER_1 0x4000 /* Enable user exception #1 */ 419 #define PCI_SXP_EXCEPT_SCAM 0x0400 /* SCAM Selection enable */ 420 #define SXP_EXCEPT_BUS_FREE 0x0200 /* Enable Bus Free det */ 421 #define SXP_EXCEPT_TARGET_ATN 0x0100 /* Enable TGT mode atten det */ 422 #define SXP_EXCEPT_RESELECTED 0x0080 /* Enable ReSEL exc handling */ 423 #define SXP_EXCEPT_SELECTED 0x0040 /* Enable SEL exc handling */ 424 #define SXP_EXCEPT_ARBITRATION 0x0020 /* Enable ARB exc handling */ 425 #define SXP_EXCEPT_GROSS_ERR 0x0010 /* Enable gross error except */ 426 #define SXP_EXCEPT_BUS_RESET 0x0008 /* Enable Bus Reset except */ 427 428 /* SXP OVERRIDE REGISTER */ 429 #define SXP_ORIDE_EXT_TRIGGER 0x8000 /* Enable external trigger */ 430 #define SXP_ORIDE_STEP 0x4000 /* Enable single step mode */ 431 #define SXP_ORIDE_BREAKPOINT 0x2000 /* Enable breakpoint reg */ 432 #define SXP_ORIDE_PIN_WRITE 0x1000 /* Enable write to SCSI pins */ 433 #define SXP_ORIDE_FORCE_OUTPUTS 0x0800 /* Force SCSI outputs on */ 434 #define SXP_ORIDE_LOOPBACK 0x0400 /* Enable SCSI loopback mode */ 435 #define SXP_ORIDE_PARITY_TEST 0x0200 /* Enable parity test mode */ 436 #define SXP_ORIDE_TRISTATE_ENA_PINS 0x0100 /* Tristate SCSI enable pins */ 437 #define SXP_ORIDE_TRISTATE_PINS 0x0080 /* Tristate SCSI pins */ 438 #define SXP_ORIDE_FIFO_RESET 0x0008 /* Reset SCSI FIFO */ 439 #define SXP_ORIDE_CMD_TERMINATE 0x0004 /* Terminate cur SXP com */ 440 #define SXP_ORIDE_RESET_REG 0x0002 /* Reset SXP registers */ 441 #define SXP_ORIDE_RESET_MODULE 0x0001 /* Reset SXP module */ 442 443 /* SXP COMMANDS */ 444 #define SXP_RESET_BUS_CMD 0x300b 445 446 /* SXP SCSI ID REGISTER */ 447 #define SXP_SELECTING_ID 0x0F00 /* (Re)Selecting id */ 448 #define SXP_SELECT_ID 0x000F /* Select id */ 449 450 /* SXP DEV CONFIG1 REGISTER */ 451 #define SXP_DCONF1_SYNC_HOLD 0x7000 /* Synchronous data hold */ 452 #define SXP_DCONF1_SYNC_SETUP 0x0F00 /* Synchronous data setup */ 453 #define SXP_DCONF1_SYNC_OFFSET 0x000F /* Synchronous data offset */ 454 455 456 /* SXP DEV CONFIG2 REGISTER */ 457 #define SXP_DCONF2_FLAGS_MASK 0xF000 /* Device flags */ 458 #define SXP_DCONF2_WIDE 0x0400 /* Enable wide SCSI */ 459 #define SXP_DCONF2_PARITY 0x0200 /* Enable parity checking */ 460 #define SXP_DCONF2_BLOCK_MODE 0x0100 /* Enable blk mode xfr count */ 461 #define SXP_DCONF2_ASSERTION_MASK 0x0007 /* Assersion period mask */ 462 463 464 /* SXP PHASE POINTER REGISTER */ 465 #define SXP_PHASE_STATUS_PTR 0x1000 /* Status buffer offset */ 466 #define SXP_PHASE_MSG_IN_PTR 0x0700 /* Msg in buffer offset */ 467 #define SXP_PHASE_COM_PTR 0x00F0 /* Command buffer offset */ 468 #define SXP_PHASE_MSG_OUT_PTR 0x0007 /* Msg out buffer offset */ 469 470 471 /* SXP FIFO STATUS REGISTER */ 472 #define SXP_FIFO_TOP_RESID 0x8000 /* Top residue reg full */ 473 #define SXP_FIFO_ACK_RESID 0x4000 /* Wide transfers odd resid */ 474 #define SXP_FIFO_COUNT_MASK 0x001C /* Words in SXP FIFO */ 475 #define SXP_FIFO_BOTTOM_RESID 0x0001 /* Bottom residue reg full */ 476 477 478 /* SXP CONTROL PINS REGISTER */ 479 #define SXP_PINS_CON_PHASE 0x8000 /* Scsi phase valid */ 480 #define SXP_PINS_CON_PARITY_HI 0x0400 /* Parity pin */ 481 #define SXP_PINS_CON_PARITY_LO 0x0200 /* Parity pin */ 482 #define SXP_PINS_CON_REQ 0x0100 /* SCSI bus REQUEST */ 483 #define SXP_PINS_CON_ACK 0x0080 /* SCSI bus ACKNOWLEDGE */ 484 #define SXP_PINS_CON_RST 0x0040 /* SCSI bus RESET */ 485 #define SXP_PINS_CON_BSY 0x0020 /* SCSI bus BUSY */ 486 #define SXP_PINS_CON_SEL 0x0010 /* SCSI bus SELECT */ 487 #define SXP_PINS_CON_ATN 0x0008 /* SCSI bus ATTENTION */ 488 #define SXP_PINS_CON_MSG 0x0004 /* SCSI bus MESSAGE */ 489 #define SXP_PINS_CON_CD 0x0002 /* SCSI bus COMMAND */ 490 #define SXP_PINS_CON_IO 0x0001 /* SCSI bus INPUT */ 491 492 /* 493 * Set the hold time for the SCSI Bus Reset to be 250 ms 494 */ 495 #define SXP_SCSI_BUS_RESET_HOLD_TIME 250 496 497 /* SXP DIFF PINS REGISTER */ 498 #define SXP_PINS_DIFF_SENSE 0x0200 /* DIFFSENS sig on SCSI bus */ 499 #define SXP_PINS_DIFF_MODE 0x0100 /* DIFFM signal */ 500 #define SXP_PINS_DIFF_ENABLE_OUTPUT 0x0080 /* Enable SXP SCSI data drv */ 501 #define SXP_PINS_DIFF_PINS_MASK 0x007C /* Differential control pins */ 502 #define SXP_PINS_DIFF_TARGET 0x0002 /* Enable SXP target mode */ 503 #define SXP_PINS_DIFF_INITIATOR 0x0001 /* Enable SXP initiator mode */ 504 505 /* 1080 only */ 506 #define SXP_PINS_LVD_MODE 0x1000 507 #define SXP_PINS_HVD_MODE 0x0800 508 #define SXP_PINS_SE_MODE 0x0400 509 510 /* The above have to be put together with the DIFFM pin to make sense */ 511 #define ISP1080_LVD_MODE (SXP_PINS_LVD_MODE) 512 #define ISP1080_HVD_MODE (SXP_PINS_HVD_MODE|SXP_PINS_DIFF_MODE) 513 #define ISP1080_SE_MODE (SXP_PINS_SE_MODE) 514 #define ISP1080_MODE_MASK \ 515 (SXP_PINS_LVD_MODE|SXP_PINS_HVD_MODE|SXP_PINS_SE_MODE|SXP_PINS_DIFF_MODE) 516 517 /* 518 * RISC and Host Command and Control Block Register Offsets 519 */ 520 521 #define RISC_ACC RISC_BLOCK+0x0 /* RW*: Accumulator */ 522 #define RISC_R1 RISC_BLOCK+0x2 /* RW*: GP Reg R1 */ 523 #define RISC_R2 RISC_BLOCK+0x4 /* RW*: GP Reg R2 */ 524 #define RISC_R3 RISC_BLOCK+0x6 /* RW*: GP Reg R3 */ 525 #define RISC_R4 RISC_BLOCK+0x8 /* RW*: GP Reg R4 */ 526 #define RISC_R5 RISC_BLOCK+0xA /* RW*: GP Reg R5 */ 527 #define RISC_R6 RISC_BLOCK+0xC /* RW*: GP Reg R6 */ 528 #define RISC_R7 RISC_BLOCK+0xE /* RW*: GP Reg R7 */ 529 #define RISC_R8 RISC_BLOCK+0x10 /* RW*: GP Reg R8 */ 530 #define RISC_R9 RISC_BLOCK+0x12 /* RW*: GP Reg R9 */ 531 #define RISC_R10 RISC_BLOCK+0x14 /* RW*: GP Reg R10 */ 532 #define RISC_R11 RISC_BLOCK+0x16 /* RW*: GP Reg R11 */ 533 #define RISC_R12 RISC_BLOCK+0x18 /* RW*: GP Reg R12 */ 534 #define RISC_R13 RISC_BLOCK+0x1a /* RW*: GP Reg R13 */ 535 #define RISC_R14 RISC_BLOCK+0x1c /* RW*: GP Reg R14 */ 536 #define RISC_R15 RISC_BLOCK+0x1e /* RW*: GP Reg R15 */ 537 #define RISC_PSR RISC_BLOCK+0x20 /* RW*: Processor Status */ 538 #define RISC_IVR RISC_BLOCK+0x22 /* RW*: Interrupt Vector */ 539 #define RISC_PCR RISC_BLOCK+0x24 /* RW*: Processor Ctrl */ 540 #define RISC_RAR0 RISC_BLOCK+0x26 /* RW*: Ram Address #0 */ 541 #define RISC_RAR1 RISC_BLOCK+0x28 /* RW*: Ram Address #1 */ 542 #define RISC_LCR RISC_BLOCK+0x2a /* RW*: Loop Counter */ 543 #define RISC_PC RISC_BLOCK+0x2c /* R : Program Counter */ 544 #define RISC_MTR RISC_BLOCK+0x2e /* RW*: Memory Timing */ 545 #define RISC_MTR2100 RISC_BLOCK+0x30 546 547 #define RISC_EMB RISC_BLOCK+0x30 /* RW*: Ext Mem Boundary */ 548 #define DUAL_BANK 8 549 #define RISC_SP RISC_BLOCK+0x32 /* RW*: Stack Pointer */ 550 #define RISC_HRL RISC_BLOCK+0x3e /* R *: Hardware Rev Level */ 551 #define HCCR RISC_BLOCK+0x40 /* RW : Host Command & Ctrl */ 552 #define BP0 RISC_BLOCK+0x42 /* RW : Processor Brkpt #0 */ 553 #define BP1 RISC_BLOCK+0x44 /* RW : Processor Brkpt #1 */ 554 #define TCR RISC_BLOCK+0x46 /* W : Test Control */ 555 #define TMR RISC_BLOCK+0x48 /* W : Test Mode */ 556 557 558 /* PROCESSOR STATUS REGISTER */ 559 #define RISC_PSR_FORCE_TRUE 0x8000 560 #define RISC_PSR_LOOP_COUNT_DONE 0x4000 561 #define RISC_PSR_RISC_INT 0x2000 562 #define RISC_PSR_TIMER_ROLLOVER 0x1000 563 #define RISC_PSR_ALU_OVERFLOW 0x0800 564 #define RISC_PSR_ALU_MSB 0x0400 565 #define RISC_PSR_ALU_CARRY 0x0200 566 #define RISC_PSR_ALU_ZERO 0x0100 567 568 #define RISC_PSR_PCI_ULTRA 0x0080 569 #define RISC_PSR_SBUS_ULTRA 0x0020 570 571 #define RISC_PSR_DMA_INT 0x0010 572 #define RISC_PSR_SXP_INT 0x0008 573 #define RISC_PSR_HOST_INT 0x0004 574 #define RISC_PSR_INT_PENDING 0x0002 575 #define RISC_PSR_FORCE_FALSE 0x0001 576 577 578 /* Host Command and Control */ 579 #define HCCR_CMD_NOP 0x0000 /* NOP */ 580 #define HCCR_CMD_RESET 0x1000 /* Reset RISC */ 581 #define HCCR_CMD_PAUSE 0x2000 /* Pause RISC */ 582 #define HCCR_CMD_RELEASE 0x3000 /* Release Paused RISC */ 583 #define HCCR_CMD_STEP 0x4000 /* Single Step RISC */ 584 #define HCCR_CMD_SET_HOST_INT 0x5000 /* Set Host Interrupt */ 585 #define HCCR_CMD_CLEAR_HOST_INT 0x6000 /* Clear Host Interrupt */ 586 #define HCCR_CMD_CLEAR_RISC_INT 0x7000 /* Clear RISC interrupt */ 587 #define HCCR_CMD_BREAKPOINT 0x8000 /* Change breakpoint enables */ 588 #define PCI_HCCR_CMD_BIOS 0x9000 /* Write BIOS (disable) */ 589 #define PCI_HCCR_CMD_PARITY 0xA000 /* Write parity enable */ 590 #define PCI_HCCR_CMD_PARITY_ERR 0xE000 /* Generate parity error */ 591 #define HCCR_CMD_TEST_MODE 0xF000 /* Set Test Mode */ 592 593 #define ISP2100_HCCR_PARITY_ENABLE_2 0x0400 594 #define ISP2100_HCCR_PARITY_ENABLE_1 0x0200 595 #define ISP2100_HCCR_PARITY_ENABLE_0 0x0100 596 #define ISP2100_HCCR_PARITY 0x0001 597 598 #define PCI_HCCR_PARITY 0x0400 /* Parity error flag */ 599 #define PCI_HCCR_PARITY_ENABLE_1 0x0200 /* Parity enable bank 1 */ 600 #define PCI_HCCR_PARITY_ENABLE_0 0x0100 /* Parity enable bank 0 */ 601 602 #define HCCR_HOST_INT 0x0080 /* R : Host interrupt set */ 603 #define HCCR_RESET 0x0040 /* R : reset in progress */ 604 #define HCCR_PAUSE 0x0020 /* R : RISC paused */ 605 606 #define PCI_HCCR_BIOS 0x0001 /* W : BIOS enable */ 607 608 /* 609 * Qlogic 1XXX NVRAM is an array of 128 bytes. 610 * 611 * Some portion of the front of this is for general host adapter properties 612 * This is followed by an array of per-target parameters, and is tailed off 613 * with a checksum xor byte at offset 127. For non-byte entities data is 614 * stored in Little Endian order. 615 */ 616 617 #define ISP_NVRAM_SIZE 128 618 619 #define ISPBSMX(c, byte, shift, mask) \ 620 (((c)[(byte)] >> (shift)) & (mask)) 621 622 #define ISP_NVRAM_VERSION(c) (c)[4] 623 #define ISP_NVRAM_FIFO_THRESHOLD(c) ISPBSMX(c, 5, 0, 0x03) 624 #define ISP_NVRAM_BIOS_DISABLE(c) ISPBSMX(c, 5, 2, 0x01) 625 #define ISP_NVRAM_HBA_ENABLE(c) ISPBSMX(c, 5, 3, 0x01) 626 #define ISP_NVRAM_INITIATOR_ID(c) ISPBSMX(c, 5, 4, 0x0f) 627 #define ISP_NVRAM_BUS_RESET_DELAY(c) (c)[6] 628 #define ISP_NVRAM_BUS_RETRY_COUNT(c) (c)[7] 629 #define ISP_NVRAM_BUS_RETRY_DELAY(c) (c)[8] 630 #define ISP_NVRAM_ASYNC_DATA_SETUP_TIME(c) ISPBSMX(c, 9, 0, 0x0f) 631 #define ISP_NVRAM_REQ_ACK_ACTIVE_NEGATION(c) ISPBSMX(c, 9, 4, 0x01) 632 #define ISP_NVRAM_DATA_LINE_ACTIVE_NEGATION(c) ISPBSMX(c, 9, 5, 0x01) 633 #define ISP_NVRAM_DATA_DMA_BURST_ENABLE(c) ISPBSMX(c, 9, 6, 0x01) 634 #define ISP_NVRAM_CMD_DMA_BURST_ENABLE(c) ISPBSMX(c, 9, 7, 0x01) 635 #define ISP_NVRAM_TAG_AGE_LIMIT(c) (c)[10] 636 #define ISP_NVRAM_LOWTRM_ENABLE(c) ISPBSMX(c, 11, 0, 0x01) 637 #define ISP_NVRAM_HITRM_ENABLE(c) ISPBSMX(c, 11, 1, 0x01) 638 #define ISP_NVRAM_PCMC_BURST_ENABLE(c) ISPBSMX(c, 11, 2, 0x01) 639 #define ISP_NVRAM_ENABLE_60_MHZ(c) ISPBSMX(c, 11, 3, 0x01) 640 #define ISP_NVRAM_SCSI_RESET_DISABLE(c) ISPBSMX(c, 11, 4, 0x01) 641 #define ISP_NVRAM_ENABLE_AUTO_TERM(c) ISPBSMX(c, 11, 5, 0x01) 642 #define ISP_NVRAM_FIFO_THRESHOLD_128(c) ISPBSMX(c, 11, 6, 0x01) 643 #define ISP_NVRAM_AUTO_TERM_SUPPORT(c) ISPBSMX(c, 11, 7, 0x01) 644 #define ISP_NVRAM_SELECTION_TIMEOUT(c) (((c)[12]) | ((c)[13] << 8)) 645 #define ISP_NVRAM_MAX_QUEUE_DEPTH(c) (((c)[14]) | ((c)[15] << 8)) 646 #define ISP_NVRAM_SCSI_BUS_SIZE(c) ISPBSMX(c, 16, 0, 0x01) 647 #define ISP_NVRAM_SCSI_BUS_TYPE(c) ISPBSMX(c, 16, 1, 0x01) 648 #define ISP_NVRAM_ADAPTER_CLK_SPEED(c) ISPBSMX(c, 16, 2, 0x01) 649 #define ISP_NVRAM_SOFT_TERM_SUPPORT(c) ISPBSMX(c, 16, 3, 0x01) 650 #define ISP_NVRAM_FLASH_ONBOARD(c) ISPBSMX(c, 16, 4, 0x01) 651 #define ISP_NVRAM_FAST_MTTR_ENABLE(c) ISPBSMX(c, 22, 0, 0x01) 652 653 #define ISP_NVRAM_TARGOFF 28 654 #define ISP_NVARM_TARGSIZE 6 655 #define _IxT(tgt, tidx) \ 656 (ISP_NVRAM_TARGOFF + (ISP_NVARM_TARGSIZE * (tgt)) + (tidx)) 657 #define ISP_NVRAM_TGT_RENEG(c, t) ISPBSMX(c, _IxT(t, 0), 0, 0x01) 658 #define ISP_NVRAM_TGT_QFRZ(c, t) ISPBSMX(c, _IxT(t, 0), 1, 0x01) 659 #define ISP_NVRAM_TGT_ARQ(c, t) ISPBSMX(c, _IxT(t, 0), 2, 0x01) 660 #define ISP_NVRAM_TGT_TQING(c, t) ISPBSMX(c, _IxT(t, 0), 3, 0x01) 661 #define ISP_NVRAM_TGT_SYNC(c, t) ISPBSMX(c, _IxT(t, 0), 4, 0x01) 662 #define ISP_NVRAM_TGT_WIDE(c, t) ISPBSMX(c, _IxT(t, 0), 5, 0x01) 663 #define ISP_NVRAM_TGT_PARITY(c, t) ISPBSMX(c, _IxT(t, 0), 6, 0x01) 664 #define ISP_NVRAM_TGT_DISC(c, t) ISPBSMX(c, _IxT(t, 0), 7, 0x01) 665 #define ISP_NVRAM_TGT_EXEC_THROTTLE(c, t) ISPBSMX(c, _IxT(t, 1), 0, 0xff) 666 #define ISP_NVRAM_TGT_SYNC_PERIOD(c, t) ISPBSMX(c, _IxT(t, 2), 0, 0xff) 667 #define ISP_NVRAM_TGT_SYNC_OFFSET(c, t) ISPBSMX(c, _IxT(t, 3), 0, 0x0f) 668 #define ISP_NVRAM_TGT_DEVICE_ENABLE(c, t) ISPBSMX(c, _IxT(t, 3), 4, 0x01) 669 #define ISP_NVRAM_TGT_LUN_DISABLE(c, t) ISPBSMX(c, _IxT(t, 3), 5, 0x01) 670 671 /* 672 * Qlogic 2XXX NVRAM is an array of 256 bytes. 673 * 674 * Some portion of the front of this is for general RISC engine parameters, 675 * mostly reflecting the state of the last INITIALIZE FIRMWARE mailbox command. 676 * 677 * This is followed by some general host adapter parameters, and ends with 678 * a checksum xor byte at offset 255. For non-byte entities data is stored 679 * in Little Endian order. 680 */ 681 #define ISP2100_NVRAM_SIZE 256 682 /* ISP_NVRAM_VERSION is in same overall place */ 683 #define ISP2100_NVRAM_RISCVER(c) (c)[6] 684 #define ISP2100_NVRAM_OPTIONS(c) (c)[8] 685 #define ISP2100_NVRAM_MAXFRAMELENGTH(c) (((c)[10]) | ((c)[11] << 8)) 686 #define ISP2100_NVRAM_MAXIOCBALLOCATION(c) (((c)[12]) | ((c)[13] << 8)) 687 #define ISP2100_NVRAM_EXECUTION_THROTTLE(c) (((c)[14]) | ((c)[15] << 8)) 688 #define ISP2100_NVRAM_RETRY_COUNT(c) (c)[16] 689 #define ISP2100_NVRAM_RETRY_DELAY(c) (c)[17] 690 691 #define ISP2100_NVRAM_NODE_NAME(c) (\ 692 (((u_int64_t)(c)[18]) << 56) | \ 693 (((u_int64_t)(c)[19]) << 48) | \ 694 (((u_int64_t)(c)[20]) << 40) | \ 695 (((u_int64_t)(c)[21]) << 32) | \ 696 (((u_int64_t)(c)[22]) << 24) | \ 697 (((u_int64_t)(c)[23]) << 16) | \ 698 (((u_int64_t)(c)[24]) << 8) | \ 699 (((u_int64_t)(c)[25]) << 0)) 700 #define ISP2100_NVRAM_HARDLOOPID(c) (c)[26] 701 702 #define ISP2100_NVRAM_HBA_OPTIONS(c) (c)[70] 703 #define ISP2100_NVRAM_HBA_DISABLE(c) ISPBSMX(c, 70, 0, 0x01) 704 #define ISP2100_NVRAM_BIOS_DISABLE(c) ISPBSMX(c, 70, 1, 0x01) 705 #define ISP2100_NVRAM_LUN_DISABLE(c) ISPBSMX(c, 70, 2, 0x01) 706 #define ISP2100_NVRAM_ENABLE_SELECT_BOOT(c) ISPBSMX(c, 70, 3, 0x01) 707 #define ISP2100_NVRAM_DISABLE_CODELOAD(c) ISPBSMX(c, 70, 4, 0x01) 708 #define ISP2100_NVRAM_SET_CACHELINESZ(c) ISPBSMX(c, 70, 5, 0x01) 709 710 #define ISP2100_NVRAM_BOOT_NODE_NAME(c) (\ 711 (((u_int64_t)(c)[72]) << 56) | \ 712 (((u_int64_t)(c)[73]) << 48) | \ 713 (((u_int64_t)(c)[74]) << 40) | \ 714 (((u_int64_t)(c)[75]) << 32) | \ 715 (((u_int64_t)(c)[76]) << 24) | \ 716 (((u_int64_t)(c)[77]) << 16) | \ 717 (((u_int64_t)(c)[78]) << 8) | \ 718 (((u_int64_t)(c)[79]) << 0)) 719 720 #define ISP2100_NVRAM_BOOT_LUN(c) (c)[80] 721 722 #endif /* _ISPREG_H */ 723
Indexes created Fri Sep 26 20:09:58 GMT 2025