xref: /src/sys/dev/ic/ncr53c9x.c

/*	$NetBSD: ncr53c9x.c,v 1.153 2020/04/13 00:27:17 chs Exp $	*/

/*-
 * Copyright (c) 1998, 2002 The NetBSD Foundation, Inc.
 * All rights reserved.
 *
 * This code is derived from software contributed to The NetBSD Foundation
 * by Charles M. Hannum.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
 * PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 */

/*
 * Copyright (c) 1994 Peter Galbavy
 * Copyright (c) 1995 Paul Kranenburg
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. All advertising materials mentioning features or use of this software
 *    must display the following acknowledgement:
 *	This product includes software developed by Peter Galbavy
 * 4. The name of the author may not be used to endorse or promote products
 *    derived from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
 * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 */

/*
 * Based on aic6360 by Jarle Greipsland
 *
 * Acknowledgements: Many of the algorithms used in this driver are
 * inspired by the work of Julian Elischer (julian (at) tfs.com) and
 * Charles Hannum (mycroft (at) duality.gnu.ai.mit.edu).  Thanks a million!
 */

#include <sys/cdefs.h>
__KERNEL_RCSID(0, "$NetBSD: ncr53c9x.c,v 1.153 2020/04/13 00:27:17 chs Exp $");

#include <sys/param.h>
#include <sys/systm.h>
#include <sys/callout.h>
#include <sys/kernel.h>
#include <sys/errno.h>
#include <sys/ioctl.h>
#include <sys/device.h>
#include <sys/buf.h>
#include <sys/malloc.h>
#include <sys/proc.h>
#include <sys/queue.h>
#include <sys/pool.h>
#include <sys/scsiio.h>

#include <dev/scsipi/scsi_spc.h>
#include <dev/scsipi/scsi_all.h>
#include <dev/scsipi/scsipi_all.h>
#include <dev/scsipi/scsiconf.h>
#include <dev/scsipi/scsi_message.h>

#include <dev/ic/ncr53c9xreg.h>
#include <dev/ic/ncr53c9xvar.h>

int ncr53c9x_debug = NCR_SHOWMISC; /*NCR_SHOWPHASE|NCR_SHOWMISC|NCR_SHOWTRAC|NCR_SHOWCMDS;*/
#ifdef DEBUG
int ncr53c9x_notag = 0;
#endif

static void	ncr53c9x_readregs(struct ncr53c9x_softc *);
static void	ncr53c9x_select(struct ncr53c9x_softc *, struct ncr53c9x_ecb *);
static int	ncr53c9x_reselect(struct ncr53c9x_softc *, int, int, int);
#if 0
static void	ncr53c9x_scsi_reset(struct ncr53c9x_softc *);
#endif
static void	ncr53c9x_clear(struct ncr53c9x_softc *, scsipi_xfer_result_t);
static int	ncr53c9x_poll(struct ncr53c9x_softc *,
			      struct scsipi_xfer *, int);
static void	ncr53c9x_sched(struct ncr53c9x_softc *);
static void	ncr53c9x_done(struct ncr53c9x_softc *, struct ncr53c9x_ecb *);
static void	ncr53c9x_msgin(struct ncr53c9x_softc *);
static void	ncr53c9x_msgout(struct ncr53c9x_softc *);
static void	ncr53c9x_timeout(void *arg);
static void	ncr53c9x_watch(void *arg);
static void	ncr53c9x_dequeue(struct ncr53c9x_softc *,
				 struct ncr53c9x_ecb *);
static int	ncr53c9x_ioctl(struct scsipi_channel *, u_long,
			       void *, int, struct proc *);

void ncr53c9x_sense(struct ncr53c9x_softc *, struct ncr53c9x_ecb *);
void ncr53c9x_free_ecb(struct ncr53c9x_softc *, struct ncr53c9x_ecb *);
struct ncr53c9x_ecb *ncr53c9x_get_ecb(struct ncr53c9x_softc *, int);

static inline int ncr53c9x_stp2cpb(struct ncr53c9x_softc *, int);
static inline void ncr53c9x_setsync(struct ncr53c9x_softc *,
				    struct ncr53c9x_tinfo *);
void   ncr53c9x_update_xfer_mode (struct ncr53c9x_softc *, int);
static struct ncr53c9x_linfo *ncr53c9x_lunsearch(struct ncr53c9x_tinfo *,
						 int64_t lun);

static void ncr53c9x_wrfifo(struct ncr53c9x_softc *, uint8_t *, int);

static int  ncr53c9x_rdfifo(struct ncr53c9x_softc *, int);
#define NCR_RDFIFO_START   0
#define NCR_RDFIFO_CONTINUE 1


#define NCR_SET_COUNT(sc, size) do { \
		NCR_WRITE_REG((sc), NCR_TCL, (size));			\
		NCR_WRITE_REG((sc), NCR_TCM, (size) >> 8);		\
		if ((sc->sc_cfg2 & NCRCFG2_FE) ||			\
		    (sc->sc_rev == NCR_VARIANT_FAS366)) {		\
			NCR_WRITE_REG((sc), NCR_TCH, (size) >> 16);	\
		}							\
		if (sc->sc_rev == NCR_VARIANT_FAS366) {			\
			NCR_WRITE_REG(sc, NCR_RCH, 0);			\
		}							\
} while (/* CONSTCOND */0)

static int ecb_pool_initialized = 0;
static struct pool ecb_pool;

/*
 * Names for the NCR53c9x variants, corresponding to the variant tags
 * in ncr53c9xvar.h.
 */
static const char *ncr53c9x_variant_names[] = {
	"ESP100",
	"ESP100A",
	"ESP200",
	"NCR53C94",
	"NCR53C96",
	"ESP406",
	"FAS408",
	"FAS216",
	"AM53C974",
	"FAS366/HME",
	"NCR53C90 (86C01)",
};

/*
 * Search linked list for LUN info by LUN id.
 */
static struct ncr53c9x_linfo *
ncr53c9x_lunsearch(struct ncr53c9x_tinfo *ti, int64_t lun)
{
	struct ncr53c9x_linfo *li;

	LIST_FOREACH(li, &ti->luns, link)
		if (li->lun == lun)
			return li;
	return NULL;
}

/*
 * Attach this instance, and then all the sub-devices
 */
void
ncr53c9x_attach(struct ncr53c9x_softc *sc)
{
	struct scsipi_adapter *adapt = &sc->sc_adapter;
	struct scsipi_channel *chan = &sc->sc_channel;

	mutex_init(&sc->sc_lock, MUTEX_DEFAULT, IPL_BIO);

	callout_init(&sc->sc_watchdog, 0);

	/*
	 * Note, the front-end has set us up to print the chip variation.
	 */
	if (sc->sc_rev >= NCR_VARIANT_MAX) {
		aprint_error(": unknown variant %d, devices not attached\n",
		    sc->sc_rev);
		return;
	}

	aprint_normal(": %s, %dMHz, SCSI ID %d\n",
	    ncr53c9x_variant_names[sc->sc_rev], sc->sc_freq, sc->sc_id);

	sc->sc_ntarg = (sc->sc_rev == NCR_VARIANT_FAS366) ? 16 : 8;

	/*
	 * Allocate SCSI message buffers.
	 * Front-ends can override allocation to avoid alignment
	 * handling in the DMA engines. Note that that ncr53c9x_msgout()
	 * can request a 1 byte DMA transfer.
	 */
	if (sc->sc_omess == NULL)
		sc->sc_omess = malloc(NCR_MAX_MSG_LEN, M_DEVBUF, M_WAITOK);

	if (sc->sc_imess == NULL)
		sc->sc_imess = malloc(NCR_MAX_MSG_LEN + 1, M_DEVBUF, M_WAITOK);

	sc->sc_tinfo = malloc(sc->sc_ntarg * sizeof(sc->sc_tinfo[0]),
	    M_DEVBUF, M_WAITOK | M_ZERO);

	/*
	 * Treat NCR53C90 with the 86C01 DMA chip exactly as ESP100
	 * from now on.
	 */
	if (sc->sc_rev == NCR_VARIANT_NCR53C90_86C01)
		sc->sc_rev = NCR_VARIANT_ESP100;

	sc->sc_ccf = FREQTOCCF(sc->sc_freq);

	/* The value *must not* be == 1. Make it 2 */
	if (sc->sc_ccf == 1)
		sc->sc_ccf = 2;

	/*
	 * The recommended timeout is 250ms. This register is loaded
	 * with a value calculated as follows, from the docs:
	 *
	 *		(timout period) x (CLK frequency)
	 *	reg = -------------------------------------
	 *		 8192 x (Clock Conversion Factor)
	 *
	 * Since CCF has a linear relation to CLK, this generally computes
	 * to the constant of 153.
	 */
	sc->sc_timeout = ((250 * 1000) * sc->sc_freq) / (8192 * sc->sc_ccf);

	/* CCF register only has 3 bits; 0 is actually 8 */
	sc->sc_ccf &= 7;

	/*
	 * Fill in the scsipi_adapter.
	 */
	adapt->adapt_dev = sc->sc_dev;
	adapt->adapt_nchannels = 1;
	adapt->adapt_openings = 256;
	adapt->adapt_max_periph = 256;
	adapt->adapt_ioctl = ncr53c9x_ioctl;
	/* adapt_request initialized by front-end */
	/* adapt_minphys initialized by front-end */

	/*
	 * Fill in the scsipi_channel.
	 */
	memset(chan, 0, sizeof(*chan));
	chan->chan_adapter = adapt;
	chan->chan_bustype = &scsi_bustype;
	chan->chan_channel = 0;
	chan->chan_ntargets = sc->sc_ntarg;
	chan->chan_nluns = 8;
	chan->chan_id = sc->sc_id;

	/*
	 * Add reference to adapter so that we drop the reference after
	 * config_found() to make sure the adapter is disabled.
	 */
	if (scsipi_adapter_addref(adapt) != 0) {
		aprint_error_dev(sc->sc_dev, "unable to enable controller\n");
		return;
	}

	/* Reset state & bus */
	sc->sc_cfflags = device_cfdata(sc->sc_dev)->cf_flags;
	sc->sc_state = 0;
	ncr53c9x_init(sc, 0);	/* no bus reset yet, leave that to scsibus* */

	/*
	 * Now try to attach all the sub-devices
	 */
	sc->sc_child = config_found(sc->sc_dev, &sc->sc_channel, scsiprint);

	scsipi_adapter_delref(adapt);
	callout_reset(&sc->sc_watchdog, 60 * hz, ncr53c9x_watch, sc);
}

int
ncr53c9x_detach(struct ncr53c9x_softc *sc, int flags)
{
	struct ncr53c9x_linfo *li, *nextli;
	int t;
	int error;

	callout_stop(&sc->sc_watchdog);

	if (sc->sc_tinfo) {
		/* Cancel all commands. */
		ncr53c9x_clear(sc, XS_DRIVER_STUFFUP);

		/* Free logical units. */
		for (t = 0; t < sc->sc_ntarg; t++) {
			for (li = LIST_FIRST(&sc->sc_tinfo[t].luns); li;
			    li = nextli) {
				nextli = LIST_NEXT(li, link);
				free(li, M_DEVBUF);
			}
		}
	}

	if (sc->sc_child) {
		error = config_detach(sc->sc_child, flags);
		if (error)
			return error;
	}

	if (sc->sc_imess)
		free(sc->sc_imess, M_DEVBUF);
	if (sc->sc_omess)
		free(sc->sc_omess, M_DEVBUF);

	mutex_destroy(&sc->sc_lock);

	return 0;
}

/*
 * This is the generic ncr53c9x reset function. It does not reset the SCSI bus,
 * only this controller, but kills any on-going commands, and also stops
 * and resets the DMA.
 *
 * After reset, registers are loaded with the defaults from the attach
 * routine above.
 */
void
ncr53c9x_reset(struct ncr53c9x_softc *sc)
{

	/* reset DMA first */
	NCRDMA_RESET(sc);

	/* reset SCSI chip */
	NCRCMD(sc, NCRCMD_RSTCHIP);
	NCRCMD(sc, NCRCMD_NOP);
	DELAY(500);

	/* do these backwards, and fall through */
	switch (sc->sc_rev) {
	case NCR_VARIANT_ESP406:
	case NCR_VARIANT_FAS408:
		NCR_WRITE_REG(sc, NCR_CFG5, sc->sc_cfg5 | NCRCFG5_SINT);
		NCR_WRITE_REG(sc, NCR_CFG4, sc->sc_cfg4);
		/* FALLTHROUGH */
	case NCR_VARIANT_AM53C974:
	case NCR_VARIANT_FAS216:
	case NCR_VARIANT_NCR53C94:
	case NCR_VARIANT_NCR53C96:
	case NCR_VARIANT_ESP200:
		sc->sc_features |= NCR_F_HASCFG3;
		NCR_WRITE_REG(sc, NCR_CFG3, sc->sc_cfg3);
		/* FALLTHROUGH */
	case NCR_VARIANT_ESP100A:
		sc->sc_features |= NCR_F_SELATN3;
		NCR_WRITE_REG(sc, NCR_CFG2, sc->sc_cfg2);
		/* FALLTHROUGH */
	case NCR_VARIANT_ESP100:
		NCR_WRITE_REG(sc, NCR_CFG1, sc->sc_cfg1);
		NCR_WRITE_REG(sc, NCR_CCF, sc->sc_ccf);
		NCR_WRITE_REG(sc, NCR_SYNCOFF, 0);
		NCR_WRITE_REG(sc, NCR_TIMEOUT, sc->sc_timeout);
		break;

	case NCR_VARIANT_FAS366:
		sc->sc_features |=
		    NCR_F_HASCFG3 | NCR_F_FASTSCSI | NCR_F_SELATN3;
		sc->sc_cfg3 = NCRFASCFG3_FASTCLK | NCRFASCFG3_OBAUTO;
		sc->sc_cfg3_fscsi = NCRFASCFG3_FASTSCSI;
		NCR_WRITE_REG(sc, NCR_CFG3, sc->sc_cfg3);
		sc->sc_cfg2 = 0; /* NCRCFG2_HMEFE| NCRCFG2_HME32 */
		NCR_WRITE_REG(sc, NCR_CFG2, sc->sc_cfg2);
		NCR_WRITE_REG(sc, NCR_CFG1, sc->sc_cfg1);
		NCR_WRITE_REG(sc, NCR_CCF, sc->sc_ccf);
		NCR_WRITE_REG(sc, NCR_SYNCOFF, 0);
		NCR_WRITE_REG(sc, NCR_TIMEOUT, sc->sc_timeout);
		break;

	default:
		printf("%s: unknown revision code, assuming ESP100\n",
		    device_xname(sc->sc_dev));
		NCR_WRITE_REG(sc, NCR_CFG1, sc->sc_cfg1);
		NCR_WRITE_REG(sc, NCR_CCF, sc->sc_ccf);
		NCR_WRITE_REG(sc, NCR_SYNCOFF, 0);
		NCR_WRITE_REG(sc, NCR_TIMEOUT, sc->sc_timeout);
	}

	if (sc->sc_rev == NCR_VARIANT_AM53C974)
		NCR_WRITE_REG(sc, NCR_AMDCFG4, sc->sc_cfg4);

#if 0
	printf("%s: ncr53c9x_reset: revision %d\n",
	    device_xname(sc->sc_dev), sc->sc_rev);
	printf("%s: ncr53c9x_reset: cfg1 0x%x, cfg2 0x%x, cfg3 0x%x, "
	    "ccf 0x%x, timeout 0x%x\n",
	    device_xname(sc->sc_dev), sc->sc_cfg1, sc->sc_cfg2, sc->sc_cfg3,
	    sc->sc_ccf, sc->sc_timeout);
#endif
}

#if 0
/*
 * Reset the SCSI bus, but not the chip
 */
void
ncr53c9x_scsi_reset(struct ncr53c9x_softc *sc)
{

	(*sc->sc_glue->gl_dma_stop)(sc);

	printf("%s: resetting SCSI bus\n", device_xname(sc->sc_dev));
	NCRCMD(sc, NCRCMD_RSTSCSI);
}
#endif

/*
 * Clear all commands
 */
void
ncr53c9x_clear(struct ncr53c9x_softc *sc, scsipi_xfer_result_t result)
{
	struct ncr53c9x_ecb *ecb;
	struct ncr53c9x_linfo *li;
	int i, r;

	/* Cancel any active commands. */
	sc->sc_state = NCR_CLEANING;
	sc->sc_msgify = 0;
	ecb = sc->sc_nexus;
	if (ecb != NULL) {
		ecb->xs->error = result;
		ncr53c9x_done(sc, ecb);
	}
	/* Cancel outstanding disconnected commands on each LUN */
	for (r = 0; r < sc->sc_ntarg; r++) {
		LIST_FOREACH(li, &sc->sc_tinfo[r].luns, link) {
			ecb = li->untagged;
			if (ecb != NULL) {
				li->untagged = NULL;
				/*
				 * XXXXXXX
				 *
				 * Should we terminate a command
				 * that never reached the disk?
				 */
				li->busy = 0;
				ecb->xs->error = result;
				ncr53c9x_done(sc, ecb);
			}
			for (i = 0; i < 256; i++) {
				ecb = li->queued[i];
				if (ecb != NULL) {
					li->queued[i] = NULL;
					ecb->xs->error = result;
					ncr53c9x_done(sc, ecb);
				}
			}
			li->used = 0;
		}
	}
}

/*
 * Initialize ncr53c9x state machine
 */
void
ncr53c9x_init(struct ncr53c9x_softc *sc, int doreset)
{
	int r;

	NCR_MISC(("[NCR_INIT(%d) %d] ", doreset, sc->sc_state));

	if (!ecb_pool_initialized) {
		/* All instances share this pool */
		pool_init(&ecb_pool, sizeof(struct ncr53c9x_ecb), 0, 0, 0,
		    "ncr53c9x_ecb", NULL, IPL_BIO);
		/* make sure to always have some items to play with */
		pool_prime(&ecb_pool, 1);
		ecb_pool_initialized = 1;
	}

	if (sc->sc_state == 0) {
		/* First time through; initialize. */

		TAILQ_INIT(&sc->ready_list);
		sc->sc_nexus = NULL;
		memset(sc->sc_tinfo, 0, sizeof(*sc->sc_tinfo));
		for (r = 0; r < sc->sc_ntarg; r++) {
			LIST_INIT(&sc->sc_tinfo[r].luns);
		}
	} else {
		ncr53c9x_clear(sc, XS_TIMEOUT);
	}

	/*
	 * reset the chip to a known state
	 */
	ncr53c9x_reset(sc);

	sc->sc_flags = 0;
	sc->sc_msgpriq = sc->sc_msgout = sc->sc_msgoutq = 0;
	sc->sc_phase = sc->sc_prevphase = INVALID_PHASE;

	/* XXXSMP scsipi */
	KERNEL_LOCK(1, curlwp);

	for (r = 0; r < sc->sc_ntarg; r++) {
		struct ncr53c9x_tinfo *ti = &sc->sc_tinfo[r];
/* XXX - config flags per target: low bits: no reselect; high bits: no synch */

		ti->flags = ((sc->sc_minsync &&
		    !(sc->sc_cfflags & (1 << ((r & 7) + 8)))) ?
		    0 : T_SYNCHOFF) |
		    ((sc->sc_cfflags & (1 << (r & 7))) ? T_RSELECTOFF : 0);
#ifdef DEBUG
		if (ncr53c9x_notag)
			ti->flags &= ~T_TAG;
#endif
		ti->period = sc->sc_minsync;
		ti->offset = 0;
		ti->cfg3   = 0;

		ncr53c9x_update_xfer_mode(sc, r);
	}

	if (doreset) {
		sc->sc_state = NCR_SBR;
		NCRCMD(sc, NCRCMD_RSTSCSI);

		/* Notify upper layer */
		scsipi_async_event(&sc->sc_channel, ASYNC_EVENT_RESET, NULL);
	} else {
		sc->sc_state = NCR_IDLE;
		ncr53c9x_sched(sc);
	}

	/* XXXSMP scsipi */
	KERNEL_UNLOCK_ONE(curlwp);
}

/*
 * Read the NCR registers, and save their contents for later use.
 * NCR_STAT, NCR_STEP & NCR_INTR are mostly zeroed out when reading
 * NCR_INTR - so make sure it is the last read.
 *
 * I think that (from reading the docs) most bits in these registers
 * only make sense when he DMA CSR has an interrupt showing. Call only
 * if an interrupt is pending.
 */
inline void
ncr53c9x_readregs(struct ncr53c9x_softc *sc)
{

	sc->sc_espstat = NCR_READ_REG(sc, NCR_STAT);
	/* Only the stepo bits are of interest */
	sc->sc_espstep = NCR_READ_REG(sc, NCR_STEP) & NCRSTEP_MASK;

	if (sc->sc_rev == NCR_VARIANT_FAS366)
		sc->sc_espstat2 = NCR_READ_REG(sc, NCR_STAT2);

	sc->sc_espintr = NCR_READ_REG(sc, NCR_INTR);

	if (sc->sc_glue->gl_clear_latched_intr != NULL)
		(*sc->sc_glue->gl_clear_latched_intr)(sc);

	/*
	 * Determine the SCSI bus phase, return either a real SCSI bus phase
	 * or some pseudo phase we use to detect certain exceptions.
	 */

	sc->sc_phase = (sc->sc_espintr & NCRINTR_DIS) ?
	    /* Disconnected */ BUSFREE_PHASE : sc->sc_espstat & NCRSTAT_PHASE;

	NCR_INTS(("regs[intr=%02x,stat=%02x,step=%02x,stat2=%02x] ",
	    sc->sc_espintr, sc->sc_espstat, sc->sc_espstep, sc->sc_espstat2));
}

/*
 * Convert Synchronous Transfer Period to chip register Clock Per Byte value.
 */
static inline int
ncr53c9x_stp2cpb(struct ncr53c9x_softc *sc, int period)
{
	int v;

	v = (sc->sc_freq * period) / 250;
	if (ncr53c9x_cpb2stp(sc, v) < period)
		/* Correct round-down error */
		v++;
	return v;
}

static inline void
ncr53c9x_setsync(struct ncr53c9x_softc *sc, struct ncr53c9x_tinfo *ti)
{
	uint8_t syncoff, synctp;
	uint8_t cfg3 = sc->sc_cfg3 | ti->cfg3;

	if (ti->flags & T_SYNCMODE) {
		syncoff = ti->offset;
		synctp = ncr53c9x_stp2cpb(sc, ti->period);
		if (sc->sc_features & NCR_F_FASTSCSI) {
			/*
			 * If the period is 200ns or less (ti->period <= 50),
			 * put the chip in Fast SCSI mode.
			 */
			if (ti->period <= 50)
				/*
				 * There are (at least) 4 variations of the
				 * configuration 3 register.  The drive attach
				 * routine sets the appropriate bit to put the
				 * chip into Fast SCSI mode so that it doesn't
				 * have to be figured out here each time.
				 */
				cfg3 |= sc->sc_cfg3_fscsi;
		}

		/*
		 * Am53c974 requires different SYNCTP values when the
		 * FSCSI bit is off.
		 */
		if (sc->sc_rev == NCR_VARIANT_AM53C974 &&
		    (cfg3 & NCRAMDCFG3_FSCSI) == 0)
			synctp--;
	} else {
		syncoff = 0;
		synctp = 0;
	}

	if (sc->sc_features & NCR_F_HASCFG3)
		NCR_WRITE_REG(sc, NCR_CFG3, cfg3);

	NCR_WRITE_REG(sc, NCR_SYNCOFF, syncoff);
	NCR_WRITE_REG(sc, NCR_SYNCTP, synctp);
}

/*
 * Send a command to a target, set the driver state to NCR_SELECTING
 * and let the caller take care of the rest.
 *
 * Keeping this as a function allows me to say that this may be done
 * by DMA instead of programmed I/O soon.
 */
void
ncr53c9x_select(struct ncr53c9x_softc *sc, struct ncr53c9x_ecb *ecb)
{
	struct scsipi_periph *periph = ecb->xs->xs_periph;
	int target = periph->periph_target;
	int lun = periph->periph_lun;
	struct ncr53c9x_tinfo *ti = &sc->sc_tinfo[target];
	int tiflags = ti->flags;
	uint8_t *cmd;
	int clen;
	bool selatn3, selatns;
	size_t dmasize;

	NCR_TRACE(("[ncr53c9x_select(t%d,l%d,cmd:%x,tag:%x,%x)] ",
	    target, lun, ecb->cmd.cmd.opcode, ecb->tag[0], ecb->tag[1]));

	sc->sc_state = NCR_SELECTING;
	/*
	 * Schedule the timeout now, the first time we will go away
	 * expecting to come back due to an interrupt, because it is
	 * always possible that the interrupt may never happen.
	 */
	if ((ecb->xs->xs_control & XS_CTL_POLL) == 0) {
		callout_reset(&ecb->xs->xs_callout, mstohz(ecb->timeout),
		    ncr53c9x_timeout, ecb);
	}

	/*
	 * The docs say the target register is never reset, and I
	 * can't think of a better place to set it
	 */
	if (sc->sc_rev == NCR_VARIANT_FAS366) {
		NCRCMD(sc, NCRCMD_FLUSH);
		NCR_WRITE_REG(sc, NCR_SELID, target | NCR_BUSID_HME);
	} else {
		NCR_WRITE_REG(sc, NCR_SELID, target);
	}
	ncr53c9x_setsync(sc, ti);

	if ((ecb->flags & ECB_SENSE) != 0) {
		/*
		 * For REQUEST SENSE, we should not send an IDENTIFY or
		 * otherwise mangle the target.  There should be no MESSAGE IN
		 * phase.
		 */
		if (sc->sc_features & NCR_F_DMASELECT) {
			/* setup DMA transfer for command */
			dmasize = clen = ecb->clen;
			sc->sc_cmdlen = clen;
			sc->sc_cmdp = (void *)&ecb->cmd.cmd;

			NCRDMA_SETUP(sc, &sc->sc_cmdp, &sc->sc_cmdlen, 0,
			    &dmasize);
			/* Program the SCSI counter */
			NCR_SET_COUNT(sc, dmasize);

			if (sc->sc_rev != NCR_VARIANT_FAS366)
				NCRCMD(sc, NCRCMD_NOP | NCRCMD_DMA);

			/* And get the targets attention */
			NCRCMD(sc, NCRCMD_SELNATN | NCRCMD_DMA);
			NCRDMA_GO(sc);
		} else {
			ncr53c9x_wrfifo(sc, (uint8_t *)&ecb->cmd.cmd,
			    ecb->clen);
			sc->sc_cmdlen = 0;
			NCRCMD(sc, NCRCMD_SELNATN);
		}
		return;
	}

	selatn3 = selatns = false;
	if (ecb->tag[0] != 0) {
		if (sc->sc_features & NCR_F_SELATN3)
			/* use SELATN3 to send tag messages */
			selatn3 = true;
		else
			/* We don't have SELATN3; use SELATNS to send tags */
			selatns = true;
	}

	if (ti->flags & T_NEGOTIATE) {
		/* We have to use SELATNS to send sync/wide messages */
		selatn3 = false;
		selatns = true;
	}

	cmd = (uint8_t *)&ecb->cmd.cmd;

	if (selatn3) {
		/* We'll use tags with SELATN3 */
		clen = ecb->clen + 3;
		cmd -= 3;
		cmd[0] = MSG_IDENTIFY(lun, 1);	/* msg[0] */
		cmd[1] = ecb->tag[0];		/* msg[1] */
		cmd[2] = ecb->tag[1];		/* msg[2] */
	} else {
		/* We don't have tags, or will send messages with SELATNS */
		clen = ecb->clen + 1;
		cmd -= 1;
		cmd[0] = MSG_IDENTIFY(lun, (tiflags & T_RSELECTOFF) == 0);
	}

	if ((sc->sc_features & NCR_F_DMASELECT) && !selatns) {

		/* setup DMA transfer for command */
		dmasize = clen;
		sc->sc_cmdlen = clen;
		sc->sc_cmdp = cmd;

		NCRDMA_SETUP(sc, &sc->sc_cmdp, &sc->sc_cmdlen, 0, &dmasize);
		/* Program the SCSI counter */
		NCR_SET_COUNT(sc, dmasize);

		/* load the count in */
		/* if (sc->sc_rev != NCR_VARIANT_FAS366) */
			NCRCMD(sc, NCRCMD_NOP | NCRCMD_DMA);

		/* And get the targets attention */
		if (selatn3) {
			sc->sc_msgout = SEND_TAG;
			sc->sc_flags |= NCR_ATN;
			NCRCMD(sc, NCRCMD_SELATN3 | NCRCMD_DMA);
		} else
			NCRCMD(sc, NCRCMD_SELATN | NCRCMD_DMA);
		NCRDMA_GO(sc);
		return;
	}

	/*
	 * Who am I. This is where we tell the target that we are
	 * happy for it to disconnect etc.
	 */

	/* Now get the command into the FIFO */
	sc->sc_cmdlen = 0;
	ncr53c9x_wrfifo(sc, cmd, clen);

	/* And get the targets attention */
	if (selatns) {
		NCR_MSGS(("SELATNS \n"));
		/* Arbitrate, select and stop after IDENTIFY message */
		NCRCMD(sc, NCRCMD_SELATNS);
	} else if (selatn3) {
		sc->sc_msgout = SEND_TAG;
		sc->sc_flags |= NCR_ATN;
		NCRCMD(sc, NCRCMD_SELATN3);
	} else
		NCRCMD(sc, NCRCMD_SELATN);
}

void
ncr53c9x_free_ecb(struct ncr53c9x_softc *sc, struct ncr53c9x_ecb *ecb)
{
	int s;

	s = splbio();
	ecb->flags = 0;
	pool_put(&ecb_pool, (void *)ecb);
	splx(s);
	return;
}

struct ncr53c9x_ecb *
ncr53c9x_get_ecb(struct ncr53c9x_softc *sc, int flags)
{
	struct ncr53c9x_ecb *ecb;
	int s;

	s = splbio();
	ecb = pool_get(&ecb_pool, PR_NOWAIT | PR_ZERO);
	if (ecb)
		ecb->flags |= ECB_ALLOC;
	splx(s);
	return ecb;
}

/*
 * DRIVER FUNCTIONS CALLABLE FROM HIGHER LEVEL DRIVERS
 */

/*
 * Start a SCSI-command
 * This function is called by the higher level SCSI-driver to queue/run
 * SCSI-commands.
 */

void
ncr53c9x_scsipi_request(struct scsipi_channel *chan, scsipi_adapter_req_t req,
    void *arg)
{
	struct scsipi_xfer *xs;
	struct scsipi_periph *periph;
	struct ncr53c9x_softc *sc;
	struct ncr53c9x_ecb *ecb;
	int flags;

	NCR_TRACE(("[ncr53c9x_scsipi_request] "));

	sc = device_private(chan->chan_adapter->adapt_dev);
	mutex_enter(&sc->sc_lock);

	switch (req) {
	case ADAPTER_REQ_RUN_XFER:
		xs = arg;
		periph = xs->xs_periph;
		flags = xs->xs_control;

		NCR_CMDS(("[0x%x, %d]->%d ", (int)xs->cmd->opcode, xs->cmdlen,
		    periph->periph_target));

		/* Get an ECB to use. */
		ecb = ncr53c9x_get_ecb(sc, xs->xs_control);
		/*
		 * This should never happen as we track resources
		 * in the mid-layer, but for now it can as pool_get()
		 * can fail.
		 */
		if (ecb == NULL) {
			scsipi_printaddr(periph);
			printf("%s: unable to allocate ecb\n",
			    device_xname(sc->sc_dev));
			xs->error = XS_RESOURCE_SHORTAGE;
			mutex_exit(&sc->sc_lock);
			scsipi_done(xs);
			return;
		}

		/* Initialize ecb */
		ecb->xs = xs;
		ecb->timeout = xs->timeout;

		if (flags & XS_CTL_RESET) {
			ecb->flags |= ECB_RESET;
			ecb->clen = 0;
			ecb->dleft = 0;
		} else {
			memcpy(&ecb->cmd.cmd, xs->cmd, xs->cmdlen);
			ecb->clen = xs->cmdlen;
			ecb->daddr = xs->data;
			ecb->dleft = xs->datalen;
		}
		ecb->stat = 0;

		TAILQ_INSERT_TAIL(&sc->ready_list, ecb, chain);
		ecb->flags |= ECB_READY;
		if (sc->sc_state == NCR_IDLE)
			ncr53c9x_sched(sc);

		if ((flags & XS_CTL_POLL) == 0)
			break;

		/* Not allowed to use interrupts, use polling instead */
		if (ncr53c9x_poll(sc, xs, ecb->timeout)) {
			ncr53c9x_timeout(ecb);
			if (ncr53c9x_poll(sc, xs, ecb->timeout))
				ncr53c9x_timeout(ecb);
		}
		break;

	case ADAPTER_REQ_GROW_RESOURCES:
		/* XXX Not supported. */
		break;

	case ADAPTER_REQ_SET_XFER_MODE:
	    {
		struct ncr53c9x_tinfo *ti;
		struct scsipi_xfer_mode *xm = arg;

		ti = &sc->sc_tinfo[xm->xm_target];
		ti->flags &= ~(T_NEGOTIATE|T_SYNCMODE);
		ti->period = 0;
		ti->offset = 0;

		if ((sc->sc_cfflags & (1 << ((xm->xm_target & 7) + 16))) == 0 &&
		    (xm->xm_mode & PERIPH_CAP_TQING)) {
			NCR_MISC(("%s: target %d: tagged queuing\n",
			    device_xname(sc->sc_dev), xm->xm_target));
			ti->flags |= T_TAG;
		} else
			ti->flags &= ~T_TAG;

		if ((xm->xm_mode & PERIPH_CAP_WIDE16) != 0) {
			NCR_MISC(("%s: target %d: wide scsi negotiation\n",
			    device_xname(sc->sc_dev), xm->xm_target));
			if (sc->sc_rev == NCR_VARIANT_FAS366) {
				ti->flags |= T_WIDE;
				ti->width = 1;
			}
		}

		if ((xm->xm_mode & PERIPH_CAP_SYNC) != 0 &&
		    (ti->flags & T_SYNCHOFF) == 0 && sc->sc_minsync != 0) {
			NCR_MISC(("%s: target %d: sync negotiation\n",
			    device_xname(sc->sc_dev), xm->xm_target));
			ti->flags |= T_NEGOTIATE;
			ti->period = sc->sc_minsync;
		}
		/*
		 * If we're not going to negotiate, send the notification
		 * now, since it won't happen later.
		 */
		if ((ti->flags & T_NEGOTIATE) == 0)
			ncr53c9x_update_xfer_mode(sc, xm->xm_target);
	    }
		break;
	}

	mutex_exit(&sc->sc_lock);
}

void
ncr53c9x_update_xfer_mode(struct ncr53c9x_softc *sc, int target)
{
	struct scsipi_xfer_mode xm;
	struct ncr53c9x_tinfo *ti = &sc->sc_tinfo[target];

	xm.xm_target = target;
	xm.xm_mode = 0;
	xm.xm_period = 0;
	xm.xm_offset = 0;

	if (ti->flags & T_SYNCMODE) {
		xm.xm_mode |= PERIPH_CAP_SYNC;
		xm.xm_period = ti->period;
		xm.xm_offset = ti->offset;
	}
	if (ti->width)
		xm.xm_mode |= PERIPH_CAP_WIDE16;

	if ((ti->flags & (T_RSELECTOFF|T_TAG)) == T_TAG)
		xm.xm_mode |= PERIPH_CAP_TQING;

	scsipi_async_event(&sc->sc_channel, ASYNC_EVENT_XFER_MODE, &xm);
}

/*
 * Used when interrupt driven I/O isn't allowed, e.g. during boot.
 */
int
ncr53c9x_poll(struct ncr53c9x_softc *sc, struct scsipi_xfer *xs, int count)
{

	NCR_TRACE(("[ncr53c9x_poll] "));
	while (count) {
		if (NCRDMA_ISINTR(sc)) {
			mutex_exit(&sc->sc_lock);
			ncr53c9x_intr(sc);
			mutex_enter(&sc->sc_lock);
		}
#if alternatively
		if (NCR_READ_REG(sc, NCR_STAT) & NCRSTAT_INT)
			ncr53c9x_intr(sc);
#endif
		if ((xs->xs_status & XS_STS_DONE) != 0)
			return 0;
		if (sc->sc_state == NCR_IDLE) {
			NCR_TRACE(("[ncr53c9x_poll: rescheduling] "));
			ncr53c9x_sched(sc);
		}
		DELAY(1000);
		count--;
	}
	return 1;
}

int
ncr53c9x_ioctl(struct scsipi_channel *chan, u_long cmd, void *arg,
    int flag, struct proc *p)
{
	struct ncr53c9x_softc *sc;
	int error = 0;

	sc = device_private(chan->chan_adapter->adapt_dev);
	switch (cmd) {
	case SCBUSIORESET:
		mutex_enter(&sc->sc_lock);
		ncr53c9x_init(sc, 1);
		mutex_exit(&sc->sc_lock);
		break;
	default:
		error = ENOTTY;
		break;
	}
	return error;
}


/*
 * LOW LEVEL SCSI UTILITIES
 */

/*
 * Schedule a scsi operation.  This has now been pulled out of the interrupt
 * handler so that we may call it from ncr53c9x_scsipi_request and
 * ncr53c9x_done.  This may save us an unnecessary interrupt just to get
 * things going.  Should only be called when state == NCR_IDLE and at bio pl.
 */
void
ncr53c9x_sched(struct ncr53c9x_softc *sc)
{
	struct ncr53c9x_ecb *ecb;
	struct scsipi_periph *periph;
	struct ncr53c9x_tinfo *ti;
	struct ncr53c9x_linfo *li;
	int lun;
	int tag;

	NCR_TRACE(("[ncr53c9x_sched] "));
	if (sc->sc_state != NCR_IDLE)
		panic("%s: not IDLE (state=%d)", __func__, sc->sc_state);

	/*
	 * Find first ecb in ready queue that is for a target/lunit
	 * combinations that is not busy.
	 */
	for (ecb = TAILQ_FIRST(&sc->ready_list); ecb != NULL;
	    ecb = TAILQ_NEXT(ecb, chain)) {
		periph = ecb->xs->xs_periph;
		ti = &sc->sc_tinfo[periph->periph_target];
		lun = periph->periph_lun;

		/* Select type of tag for this command */
		if ((ti->flags & T_RSELECTOFF) != 0)
			tag = 0;
		else if ((ti->flags & T_TAG) == 0)
			tag = 0;
		else if ((ecb->flags & ECB_SENSE) != 0)
			tag = 0;
		else
			tag = ecb->xs->xs_tag_type;
#if 0
		/* XXXX Use tags for polled commands? */
		if (ecb->xs->xs_control & XS_CTL_POLL)
			tag = 0;
#endif

		li = TINFO_LUN(ti, lun);
		if (li == NULL) {
			/* Initialize LUN info and add to list. */
			li = malloc(sizeof(*li), M_DEVBUF, M_NOWAIT|M_ZERO);
			if (li == NULL) {
				continue;
			}
			li->lun = lun;

			LIST_INSERT_HEAD(&ti->luns, li, link);
			if (lun < NCR_NLUN)
				ti->lun[lun] = li;
		}
		li->last_used = time_second;
		if (tag == 0) {
			/* Try to issue this as an un-tagged command */
			if (li->untagged == NULL)
				li->untagged = ecb;
		}
		if (li->untagged != NULL) {
			tag = 0;
			if ((li->busy != 1) && li->used == 0) {
				/* We need to issue this untagged command now */
				ecb = li->untagged;
				periph = ecb->xs->xs_periph;
			} else {
				/* Not ready yet */
				continue;
			}
		}
		ecb->tag[0] = tag;
		if (tag != 0) {
			li->queued[ecb->xs->xs_tag_id] = ecb;
			ecb->tag[1] = ecb->xs->xs_tag_id;
			li->used++;
		}
		if (li->untagged != NULL && (li->busy != 1)) {
			li->busy = 1;
			TAILQ_REMOVE(&sc->ready_list, ecb, chain);
			ecb->flags &= ~ECB_READY;
			sc->sc_nexus = ecb;
			ncr53c9x_select(sc, ecb);
			break;
		}
		if (li->untagged == NULL && tag != 0) {
			TAILQ_REMOVE(&sc->ready_list, ecb, chain);
			ecb->flags &= ~ECB_READY;
			sc->sc_nexus = ecb;
			ncr53c9x_select(sc, ecb);
			break;
		} else {
			NCR_TRACE(("%d:%d busy\n",
			    periph->periph_target,
			    periph->periph_lun));
		}
	}
}

void
ncr53c9x_sense(struct ncr53c9x_softc *sc, struct ncr53c9x_ecb *ecb)
{
	struct scsipi_xfer *xs = ecb->xs;
	struct scsipi_periph *periph = xs->xs_periph;
	struct ncr53c9x_tinfo *ti = &sc->sc_tinfo[periph->periph_target];
	struct scsi_request_sense *ss = (void *)&ecb->cmd.cmd;
	struct ncr53c9x_linfo *li;
	int lun = periph->periph_lun;

	NCR_TRACE(("requesting sense "));
	/* Next, setup a request sense command block */
	memset(ss, 0, sizeof(*ss));
	ss->opcode = SCSI_REQUEST_SENSE;
	ss->byte2 = periph->periph_lun << SCSI_CMD_LUN_SHIFT;
	ss->length = sizeof(struct scsi_sense_data);
	ecb->clen = sizeof(*ss);
	ecb->daddr = (uint8_t *)&xs->sense.scsi_sense;
	ecb->dleft = sizeof(struct scsi_sense_data);
	ecb->flags |= ECB_SENSE;
	ecb->timeout = NCR_SENSE_TIMEOUT;
	ti->senses++;
	li = TINFO_LUN(ti, lun);
	if (li->busy)
		li->busy = 0;
	ncr53c9x_dequeue(sc, ecb);
	li->untagged = ecb; /* must be executed first to fix C/A */
	li->busy = 2;
	if (ecb == sc->sc_nexus) {
		ncr53c9x_select(sc, ecb);
	} else {
		TAILQ_INSERT_HEAD(&sc->ready_list, ecb, chain);
		ecb->flags |= ECB_READY;
		if (sc->sc_state == NCR_IDLE)
			ncr53c9x_sched(sc);
	}
}

/*
 * POST PROCESSING OF SCSI_CMD (usually current)
 */
void
ncr53c9x_done(struct ncr53c9x_softc *sc, struct ncr53c9x_ecb *ecb)
{
	struct scsipi_xfer *xs = ecb->xs;
	struct scsipi_periph *periph = xs->xs_periph;
	struct ncr53c9x_tinfo *ti = &sc->sc_tinfo[periph->periph_target];
	int lun = periph->periph_lun;
	struct ncr53c9x_linfo *li = TINFO_LUN(ti, lun);

	NCR_TRACE(("[ncr53c9x_done(error:%x)] ", xs->error));

	if ((xs->xs_control & XS_CTL_POLL) == 0)
		callout_stop(&xs->xs_callout);

	/*
	 * Now, if we've come here with no error code, i.e. we've kept the
	 * initial XS_NOERROR, and the status code signals that we should
	 * check sense, we'll need to set up a request sense cmd block and
	 * push the command back into the ready queue *before* any other
	 * commands for this target/lunit, else we lose the sense info.
	 * We don't support chk sense conditions for the request sense cmd.
	 */
	if (xs->error == XS_NOERROR) {
		xs->status = ecb->stat;
		if ((ecb->flags & ECB_ABORT) != 0) {
			xs->error = XS_TIMEOUT;
		} else if ((ecb->flags & ECB_SENSE) != 0) {
			xs->error = XS_SENSE;
		} else if ((ecb->stat & ST_MASK) == SCSI_CHECK) {
			/* First, save the return values */
			xs->resid = ecb->dleft;
			ncr53c9x_sense(sc, ecb);
			return;
		} else {
			xs->resid = ecb->dleft;
		}
		if (xs->status == SCSI_QUEUE_FULL || xs->status == XS_BUSY)
			xs->error = XS_BUSY;
	}

#ifdef NCR53C9X_DEBUG
	if (ncr53c9x_debug & NCR_SHOWTRAC) {
		if (xs->resid != 0)
			printf("resid=%d ", xs->resid);
		if (xs->error == XS_SENSE)
			printf("sense=0x%02x\n",
			    xs->sense.scsi_sense.response_code);
		else
			printf("error=%d\n", xs->error);
	}
#endif

	/*
	 * Remove the ECB from whatever queue it's on.
	 */
	ncr53c9x_dequeue(sc, ecb);
	if (ecb == sc->sc_nexus) {
		sc->sc_nexus = NULL;
		if (sc->sc_state != NCR_CLEANING) {
			sc->sc_state = NCR_IDLE;
			ncr53c9x_sched(sc);
		}
	}

	if (xs->error == XS_SELTIMEOUT) {
		/* Selection timeout -- discard this LUN if empty */
		if (li->untagged == NULL && li->used == 0) {
			if (lun < NCR_NLUN)
				ti->lun[lun] = NULL;
			LIST_REMOVE(li, link);
			free(li, M_DEVBUF);
		}
	}

	ncr53c9x_free_ecb(sc, ecb);
	ti->cmds++;
	mutex_exit(&sc->sc_lock);
	scsipi_done(xs);
	mutex_enter(&sc->sc_lock);
}

void
ncr53c9x_dequeue(struct ncr53c9x_softc *sc, struct ncr53c9x_ecb *ecb)
{
	struct ncr53c9x_tinfo *ti =
	    &sc->sc_tinfo[ecb->xs->xs_periph->periph_target];
	struct ncr53c9x_linfo *li;
	int64_t lun = ecb->xs->xs_periph->periph_lun;

	li = TINFO_LUN(ti, lun);
#ifdef DIAGNOSTIC
	if (li == NULL || li->lun != lun)
		panic("%s: lun %" PRIx64 " for ecb %p does not exist",
		    __func__, lun, ecb);
#endif
	if (li->untagged == ecb) {
		li->busy = 0;
		li->untagged = NULL;
	}
	if (ecb->tag[0] && li->queued[ecb->tag[1]] != NULL) {
#ifdef DIAGNOSTIC
		if (li->queued[ecb->tag[1]] != NULL &&
		    (li->queued[ecb->tag[1]] != ecb))
			panic("%s: slot %d for lun %" PRIx64 " has %p "
			    "instead of ecb %p\n", __func__, ecb->tag[1],
			    lun,
			    li->queued[ecb->tag[1]], ecb);
#endif
		li->queued[ecb->tag[1]] = NULL;
		li->used--;
	}

	if ((ecb->flags & ECB_READY) != 0) {
		ecb->flags &= ~ECB_READY;
		TAILQ_REMOVE(&sc->ready_list, ecb, chain);
	}
}

/*
 * INTERRUPT/PROTOCOL ENGINE
 */

/*
 * Schedule an outgoing message by prioritizing it, and asserting
 * attention on the bus. We can only do this when we are the initiator
 * else there will be an illegal command interrupt.
 */
#define ncr53c9x_sched_msgout(m) \
	do {							\
		NCR_MSGS(("ncr53c9x_sched_msgout %x %d", m, __LINE__));	\
		NCRCMD(sc, NCRCMD_SETATN);			\
		sc->sc_flags |= NCR_ATN;			\
		sc->sc_msgpriq |= (m);				\
	} while (/* CONSTCOND */0)

static void
ncr53c9x_flushfifo(struct ncr53c9x_softc *sc)
{

	NCR_TRACE(("[flushfifo] "));

	NCRCMD(sc, NCRCMD_FLUSH);

	if (sc->sc_phase == COMMAND_PHASE ||
	    sc->sc_phase == MESSAGE_OUT_PHASE)
		DELAY(2);
}

static int
ncr53c9x_rdfifo(struct ncr53c9x_softc *sc, int how)
{
	int i, n;
	uint8_t *ibuf;

	switch (how) {
	case NCR_RDFIFO_START:
		ibuf = sc->sc_imess;
		sc->sc_imlen = 0;
		break;
	case NCR_RDFIFO_CONTINUE:
		ibuf = sc->sc_imess + sc->sc_imlen;
		break;
	default:
		panic("%s: bad flag", __func__);
		break;
	}

	/*
	 * XXX buffer (sc_imess) size for message
	 */

	n = NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF;

	if (sc->sc_rev == NCR_VARIANT_FAS366) {
		n *= 2;

		for (i = 0; i < n; i++)
			ibuf[i] = NCR_READ_REG(sc, NCR_FIFO);

		if (sc->sc_espstat2 & NCRFAS_STAT2_ISHUTTLE) {

			NCR_WRITE_REG(sc, NCR_FIFO, 0);
			ibuf[i++] = NCR_READ_REG(sc, NCR_FIFO);

			NCR_READ_REG(sc, NCR_FIFO);

			ncr53c9x_flushfifo(sc);
		}
	} else {
		for (i = 0; i < n; i++)
			ibuf[i] = NCR_READ_REG(sc, NCR_FIFO);
	}

	sc->sc_imlen += i;

#if 0
#ifdef NCR53C9X_DEBUG
	{
		int j;

		NCR_TRACE(("\n[rdfifo %s (%d):",
		    (how == NCR_RDFIFO_START) ? "start" : "cont",
		    (int)sc->sc_imlen));
		if (ncr53c9x_debug & NCR_SHOWTRAC) {
			for (j = 0; j < sc->sc_imlen; j++)
				printf(" %02x", sc->sc_imess[j]);
			printf("]\n");
		}
	}
#endif
#endif
	return sc->sc_imlen;
}

static void
ncr53c9x_wrfifo(struct ncr53c9x_softc *sc, uint8_t *p, int len)
{
	int i;

#ifdef NCR53C9X_DEBUG
	NCR_MSGS(("[wrfifo(%d):", len));
	if (ncr53c9x_debug & NCR_SHOWMSGS) {
		for (i = 0; i < len; i++)
			printf(" %02x", p[i]);
		printf("]\n");
	}
#endif

	for (i = 0; i < len; i++) {
		NCR_WRITE_REG(sc, NCR_FIFO, p[i]);

		if (sc->sc_rev == NCR_VARIANT_FAS366)
			NCR_WRITE_REG(sc, NCR_FIFO, 0);
	}
}

int
ncr53c9x_reselect(struct ncr53c9x_softc *sc, int message, int tagtype,
    int tagid)
{
	uint8_t selid, target, lun;
	struct ncr53c9x_ecb *ecb = NULL;
	struct ncr53c9x_tinfo *ti;
	struct ncr53c9x_linfo *li;

	if (sc->sc_rev == NCR_VARIANT_FAS366) {
		target = sc->sc_selid;
	} else {
		/*
		 * The SCSI chip made a snapshot of the data bus
		 * while the reselection was being negotiated.
		 * This enables us to determine which target did
		 * the reselect.
		 */
		selid = sc->sc_selid & ~(1 << sc->sc_id);
		if (selid & (selid - 1)) {
			printf("%s: reselect with invalid selid %02x;"
			    " sending DEVICE RESET\n",
			    device_xname(sc->sc_dev), selid);
			goto reset;
		}

		target = ffs(selid) - 1;
	}
	lun = message & 0x07;

	/*
	 * Search wait queue for disconnected cmd
	 * The list should be short, so I haven't bothered with
	 * any more sophisticated structures than a simple
	 * singly linked list.
	 */
	ti = &sc->sc_tinfo[target];
	li = TINFO_LUN(ti, lun);

	/*
	 * We can get as far as the LUN with the IDENTIFY
	 * message.  Check to see if we're running an
	 * un-tagged command.  Otherwise ack the IDENTIFY
	 * and wait for a tag message.
	 */
	if (li != NULL) {
		if (li->untagged != NULL && li->busy)
			ecb = li->untagged;
		else if (tagtype != MSG_SIMPLE_Q_TAG) {
			/* Wait for tag to come by */
			sc->sc_state = NCR_IDENTIFIED;
			return 0;
		} else if (tagtype)
			ecb = li->queued[tagid];
	}
	if (ecb == NULL) {
		printf("%s: reselect from target %d lun %d tag %x:%x "
		    "with no nexus; sending ABORT\n",
		    device_xname(sc->sc_dev), target, lun, tagtype, tagid);
		goto abort;
	}

	/* Make this nexus active again. */
	sc->sc_state = NCR_CONNECTED;
	sc->sc_nexus = ecb;
	ncr53c9x_setsync(sc, ti);

	if (ecb->flags & ECB_RESET)
		ncr53c9x_sched_msgout(SEND_DEV_RESET);
	else if (ecb->flags & ECB_ABORT)
		ncr53c9x_sched_msgout(SEND_ABORT);

	/* Do an implicit RESTORE POINTERS. */
	sc->sc_dp = ecb->daddr;
	sc->sc_dleft = ecb->dleft;

	return 0;

reset:
	ncr53c9x_sched_msgout(SEND_DEV_RESET);
	return 1;

abort:
	ncr53c9x_sched_msgout(SEND_ABORT);
	return 1;
}

static inline int
__verify_msg_format(uint8_t *p, int len)
{

	if (len == 1 && MSG_IS1BYTE(p[0]))
		return 1;
	if (len == 2 && MSG_IS2BYTE(p[0]))
		return 1;
	if (len >= 3 && MSG_ISEXTENDED(p[0]) &&
	    len == p[1] + 2)
		return 1;

	return 0;
}

/*
 * Get an incoming message as initiator.
 *
 * The SCSI bus must already be in MESSAGE_IN_PHASE and there is a
 * byte in the FIFO
 */
void
ncr53c9x_msgin(struct ncr53c9x_softc *sc)
{

	NCR_TRACE(("[ncr53c9x_msgin(curmsglen:%ld)] ", (long)sc->sc_imlen));

	if (sc->sc_imlen == 0) {
		printf("%s: msgin: no msg byte available\n",
		    device_xname(sc->sc_dev));
		return;
	}

	/*
	 * Prepare for a new message.  A message should (according
	 * to the SCSI standard) be transmitted in one single
	 * MESSAGE_IN_PHASE. If we have been in some other phase,
	 * then this is a new message.
	 */
	if (sc->sc_prevphase != MESSAGE_IN_PHASE &&
	    sc->sc_state != NCR_RESELECTED) {
		printf("%s: phase change, dropping message, "
		    "prev %d, state %d\n",
		    device_xname(sc->sc_dev), sc->sc_prevphase, sc->sc_state);
		sc->sc_flags &= ~NCR_DROP_MSGI;
		sc->sc_imlen = 0;
	}

	/*
	 * If we're going to reject the message, don't bother storing
	 * the incoming bytes.  But still, we need to ACK them.
	 */
	if ((sc->sc_flags & NCR_DROP_MSGI) != 0) {
		NCRCMD(sc, NCRCMD_MSGOK);
		printf("<dropping msg byte %x>", sc->sc_imess[sc->sc_imlen]);
		return;
	}

	if (sc->sc_imlen >= NCR_MAX_MSG_LEN) {
		ncr53c9x_sched_msgout(SEND_REJECT);
		sc->sc_flags |= NCR_DROP_MSGI;
	} else {
		uint8_t *pb;
		int plen;

		switch (sc->sc_state) {
		/*
		 * if received message is the first of reselection
		 * then first byte is selid, and then message
		 */
		case NCR_RESELECTED:
			pb = sc->sc_imess + 1;
			plen = sc->sc_imlen - 1;
			break;
		default:
			pb = sc->sc_imess;
			plen = sc->sc_imlen;
			break;
		}

		if (__verify_msg_format(pb, plen))
			goto gotit;
	}

	/* Ack what we have so far */
	NCRCMD(sc, NCRCMD_MSGOK);
	return;

gotit:
	NCR_MSGS(("gotmsg(%x) state %d", sc->sc_imess[0], sc->sc_state));
	/* we got complete message, flush the imess, */
	/* XXX nobody uses imlen below */
	sc->sc_imlen = 0;
	/*
	 * Now we should have a complete message (1 byte, 2 byte
	 * and moderately long extended messages).  We only handle
	 * extended messages which total length is shorter than
	 * NCR_MAX_MSG_LEN.  Longer messages will be amputated.
	 */
	switch (sc->sc_state) {
		struct ncr53c9x_ecb *ecb;
		struct ncr53c9x_tinfo *ti;
		struct ncr53c9x_linfo *li;
		int lun;

	case NCR_CONNECTED:
		ecb = sc->sc_nexus;
		ti = &sc->sc_tinfo[ecb->xs->xs_periph->periph_target];

		switch (sc->sc_imess[0]) {
		case MSG_CMDCOMPLETE:
			NCR_MSGS(("cmdcomplete "));
			if (sc->sc_dleft < 0) {
				scsipi_printaddr(ecb->xs->xs_periph);
				printf("%s: got %ld extra bytes\n",
				    device_xname(sc->sc_dev),
				    -(long)sc->sc_dleft);
				sc->sc_dleft = 0;
			}
			ecb->dleft = (ecb->flags & ECB_TENTATIVE_DONE) ?
			    0 : sc->sc_dleft;
			if ((ecb->flags & ECB_SENSE) == 0)
				ecb->xs->resid = ecb->dleft;
			sc->sc_state = NCR_CMDCOMPLETE;
			break;

		case MSG_MESSAGE_REJECT:
			NCR_MSGS(("msg reject (msgout=%x) ", sc->sc_msgout));
			switch (sc->sc_msgout) {
			case SEND_TAG:
				/*
				 * Target does not like tagged queuing.
				 *  - Flush the command queue
				 *  - Disable tagged queuing for the target
				 *  - Dequeue ecb from the queued array.
				 */
				printf("%s: tagged queuing rejected: "
				    "target %d\n",
				    device_xname(sc->sc_dev),
				    ecb->xs->xs_periph->periph_target);

				NCR_MSGS(("(rejected sent tag)"));
				NCRCMD(sc, NCRCMD_FLUSH);
				DELAY(1);
				ti->flags &= ~T_TAG;
				lun = ecb->xs->xs_periph->periph_lun;
				li = TINFO_LUN(ti, lun);
				if (ecb->tag[0] &&
				    li->queued[ecb->tag[1]] != NULL) {
					li->queued[ecb->tag[1]] = NULL;
					li->used--;
				}
				ecb->tag[0] = ecb->tag[1] = 0;
				li->untagged = ecb;
				li->busy = 1;
				break;

			case SEND_SDTR:
				printf("%s: sync transfer rejected: "
				    "target %d\n",
				    device_xname(sc->sc_dev),
				    ecb->xs->xs_periph->periph_target);

				sc->sc_flags &= ~NCR_SYNCHNEGO;
				ti->flags &= ~(T_NEGOTIATE | T_SYNCMODE);
				ncr53c9x_setsync(sc, ti);
				ncr53c9x_update_xfer_mode(sc,
				    ecb->xs->xs_periph->periph_target);
				break;

			case SEND_WDTR:
				printf("%s: wide transfer rejected: "
				    "target %d\n",
				    device_xname(sc->sc_dev),
				    ecb->xs->xs_periph->periph_target);
				ti->flags &= ~(T_WIDE | T_WDTRSENT);
				ti->width = 0;
				break;

			case SEND_INIT_DET_ERR:
				goto abort;
			}
			break;

		case MSG_NOOP:
			NCR_MSGS(("noop "));
			break;

		case MSG_HEAD_OF_Q_TAG:
		case MSG_SIMPLE_Q_TAG:
		case MSG_ORDERED_Q_TAG:
			NCR_MSGS(("TAG %x:%x",
			    sc->sc_imess[0], sc->sc_imess[1]));
			break;

		case MSG_DISCONNECT:
			NCR_MSGS(("disconnect "));
			ti->dconns++;
			sc->sc_state = NCR_DISCONNECT;

			/*
			 * Mark the fact that all bytes have moved. The
			 * target may not bother to do a SAVE POINTERS
			 * at this stage. This flag will set the residual
			 * count to zero on MSG COMPLETE.
			 */
			if (sc->sc_dleft == 0)
				ecb->flags |= ECB_TENTATIVE_DONE;

			break;

		case MSG_SAVEDATAPOINTER:
			NCR_MSGS(("save datapointer "));
			ecb->daddr = sc->sc_dp;
			ecb->dleft = sc->sc_dleft;
			break;

		case MSG_RESTOREPOINTERS:
			NCR_MSGS(("restore datapointer "));
			sc->sc_dp = ecb->daddr;
			sc->sc_dleft = ecb->dleft;
			break;

		case MSG_EXTENDED:
			NCR_MSGS(("extended(%x) ", sc->sc_imess[2]));
			switch (sc->sc_imess[2]) {
			case MSG_EXT_SDTR:
				NCR_MSGS(("SDTR period %d, offset %d ",
				    sc->sc_imess[3], sc->sc_imess[4]));
				if (sc->sc_imess[1] != 3)
					goto reject;
				ti->period = sc->sc_imess[3];
				ti->offset = sc->sc_imess[4];
				ti->flags &= ~T_NEGOTIATE;
				if (sc->sc_minsync == 0 ||
				    ti->offset == 0 ||
				    ti->period > 124) {
#if 0
#ifdef NCR53C9X_DEBUG
					scsipi_printaddr(ecb->xs->xs_periph);
					printf("async mode\n");
#endif
#endif
					ti->flags &= ~T_SYNCMODE;
					if ((sc->sc_flags&NCR_SYNCHNEGO) == 0) {
						/*
						 * target initiated negotiation
						 */
						ti->offset = 0;
						ncr53c9x_sched_msgout(
						    SEND_SDTR);
					}
				} else {
					int p;

					p = ncr53c9x_stp2cpb(sc, ti->period);
					ti->period = ncr53c9x_cpb2stp(sc, p);
					if ((sc->sc_flags&NCR_SYNCHNEGO) == 0) {
						/*
						 * target initiated negotiation
						 */
						if (ti->period <
						    sc->sc_minsync)
							ti->period =
							    sc->sc_minsync;
						if (ti->offset > 15)
							ti->offset = 15;
						ti->flags &= ~T_SYNCMODE;
						ncr53c9x_sched_msgout(
						    SEND_SDTR);
					} else {
						/* we are sync */
						ti->flags |= T_SYNCMODE;
					}
				}
				ncr53c9x_update_xfer_mode(sc,
				    ecb->xs->xs_periph->periph_target);
				sc->sc_flags &= ~NCR_SYNCHNEGO;
				ncr53c9x_setsync(sc, ti);
				break;

			case MSG_EXT_WDTR:
#ifdef NCR53C9X_DEBUG
				printf("%s: wide mode %d\n",
				    device_xname(sc->sc_dev), sc->sc_imess[3]);
#endif
				if (sc->sc_imess[3] == 1) {
					ti->cfg3 |= NCRFASCFG3_EWIDE;
					ncr53c9x_setsync(sc, ti);
				} else
					ti->width = 0;
				/*
				 * Device started width negotiation.
				 */
				if ((ti->flags & T_WDTRSENT) == 0)
					ncr53c9x_sched_msgout(SEND_WDTR);
				ti->flags &= ~(T_WIDE | T_WDTRSENT);
				break;
			default:
				scsipi_printaddr(ecb->xs->xs_periph);
				printf("%s: unrecognized MESSAGE EXTENDED;"
				    " sending REJECT\n",
				    device_xname(sc->sc_dev));
				goto reject;
			}
			break;
		case MSG_IGN_WIDE_RESIDUE:
			NCR_MSGS(("ignore wide residue "));
			break;

		default:
			NCR_MSGS(("ident "));
			scsipi_printaddr(ecb->xs->xs_periph);
			printf("%s: unrecognized MESSAGE (%x); sending REJECT\n",
			    device_xname(sc->sc_dev), sc->sc_imess[0]);
		reject:
			ncr53c9x_sched_msgout(SEND_REJECT);
			break;
		}
		break;

	case NCR_IDENTIFIED:
		/*
		 * IDENTIFY message was received and queue tag is expected now
		 */
		if ((sc->sc_imess[0] != MSG_SIMPLE_Q_TAG) ||
		    (sc->sc_msgify == 0)) {
			printf("%s: TAG reselect without IDENTIFY;"
			    " MSG %x;"
			    " sending DEVICE RESET\n",
			    device_xname(sc->sc_dev),
			    sc->sc_imess[0]);
			goto reset;
		}
		(void)ncr53c9x_reselect(sc, sc->sc_msgify,
		    sc->sc_imess[0], sc->sc_imess[1]);
		break;

	case NCR_RESELECTED:
		if (MSG_ISIDENTIFY(sc->sc_imess[1])) {
			sc->sc_msgify = sc->sc_imess[1];
		} else {
			printf("%s: reselect without IDENTIFY;"
			    " MSG %x;"
			    " sending DEVICE RESET\n",
			    device_xname(sc->sc_dev),
			    sc->sc_imess[1]);
			goto reset;
		}
		(void)ncr53c9x_reselect(sc, sc->sc_msgify, 0, 0);
		break;

	default:
		printf("%s: unexpected MESSAGE IN; sending DEVICE RESET\n",
		    device_xname(sc->sc_dev));
	reset:
		ncr53c9x_sched_msgout(SEND_DEV_RESET);
		break;

	abort:
		ncr53c9x_sched_msgout(SEND_ABORT);
		break;
	}

	/* if we have more messages to send set ATN */
	if (sc->sc_msgpriq)
		NCRCMD(sc, NCRCMD_SETATN);

	/* Ack last message byte */
	NCRCMD(sc, NCRCMD_MSGOK);

	/* Done, reset message pointer. */
	sc->sc_flags &= ~NCR_DROP_MSGI;
	sc->sc_imlen = 0;
}


/*
 * Send the highest priority, scheduled message
 */
void
ncr53c9x_msgout(struct ncr53c9x_softc *sc)
{
	struct ncr53c9x_tinfo *ti;
	struct ncr53c9x_ecb *ecb;
	size_t size;

	NCR_TRACE(("[ncr53c9x_msgout(priq:%x, prevphase:%x)]",
	    sc->sc_msgpriq, sc->sc_prevphase));

	/*
	 * XXX - the NCR_ATN flag is not in sync with the actual ATN
	 *	 condition on the SCSI bus. The 53c9x chip
	 *	 automatically turns off ATN before sending the
	 *	 message byte.  (see also the comment below in the
	 *	 default case when picking out a message to send)
	 */
	if (sc->sc_flags & NCR_ATN) {
		if (sc->sc_prevphase != MESSAGE_OUT_PHASE) {
		new:
			NCRCMD(sc, NCRCMD_FLUSH);
#if 0
			DELAY(1);
#endif
			sc->sc_msgoutq = 0;
			sc->sc_omlen = 0;
		}
	} else {
		if (sc->sc_prevphase == MESSAGE_OUT_PHASE) {
			ncr53c9x_sched_msgout(sc->sc_msgoutq);
			goto new;
		} else {
			printf("%s at line %d: unexpected MESSAGE OUT phase\n",
			    device_xname(sc->sc_dev), __LINE__);
		}
	}

	if (sc->sc_omlen == 0) {
		/* Pick up highest priority message */
		sc->sc_msgout = sc->sc_msgpriq & -sc->sc_msgpriq;
		sc->sc_msgoutq |= sc->sc_msgout;
		sc->sc_msgpriq &= ~sc->sc_msgout;
		sc->sc_omlen = 1;		/* "Default" message len */
		switch (sc->sc_msgout) {
		case SEND_SDTR:
			ecb = sc->sc_nexus;
			ti = &sc->sc_tinfo[ecb->xs->xs_periph->periph_target];
			sc->sc_omess[0] = MSG_EXTENDED;
			sc->sc_omess[1] = MSG_EXT_SDTR_LEN;
			sc->sc_omess[2] = MSG_EXT_SDTR;
			sc->sc_omess[3] = ti->period;
			sc->sc_omess[4] = ti->offset;
			sc->sc_omlen = 5;
			if ((sc->sc_flags & NCR_SYNCHNEGO) == 0) {
				ti->flags |= T_SYNCMODE;
				ncr53c9x_setsync(sc, ti);
			}
			break;
		case SEND_WDTR:
			ecb = sc->sc_nexus;
			ti = &sc->sc_tinfo[ecb->xs->xs_periph->periph_target];
			sc->sc_omess[0] = MSG_EXTENDED;
			sc->sc_omess[1] = MSG_EXT_WDTR_LEN;
			sc->sc_omess[2] = MSG_EXT_WDTR;
			sc->sc_omess[3] = ti->width;
			sc->sc_omlen = 4;
			break;
		case SEND_IDENTIFY:
			if (sc->sc_state != NCR_CONNECTED) {
				printf("%s at line %d: no nexus\n",
				    device_xname(sc->sc_dev), __LINE__);
			}
			ecb = sc->sc_nexus;
			sc->sc_omess[0] =
			    MSG_IDENTIFY(ecb->xs->xs_periph->periph_lun, 0);
			break;
		case SEND_TAG:
			if (sc->sc_state != NCR_CONNECTED) {
				printf("%s at line %d: no nexus\n",
				    device_xname(sc->sc_dev), __LINE__);
			}
			ecb = sc->sc_nexus;
			sc->sc_omess[0] = ecb->tag[0];
			sc->sc_omess[1] = ecb->tag[1];
			sc->sc_omlen = 2;
			break;
		case SEND_DEV_RESET:
			sc->sc_flags |= NCR_ABORTING;
			sc->sc_omess[0] = MSG_BUS_DEV_RESET;
			ecb = sc->sc_nexus;
			ti = &sc->sc_tinfo[ecb->xs->xs_periph->periph_target];
			ti->flags &= ~T_SYNCMODE;
			ncr53c9x_update_xfer_mode(sc,
			    ecb->xs->xs_periph->periph_target);
			if ((ti->flags & T_SYNCHOFF) == 0)
				/* We can re-start sync negotiation */
				ti->flags |= T_NEGOTIATE;
			break;
		case SEND_PARITY_ERROR:
			sc->sc_omess[0] = MSG_PARITY_ERROR;
			break;
		case SEND_ABORT:
			sc->sc_flags |= NCR_ABORTING;
			sc->sc_omess[0] = MSG_ABORT;
			break;
		case SEND_INIT_DET_ERR:
			sc->sc_omess[0] = MSG_INITIATOR_DET_ERR;
			break;
		case SEND_REJECT:
			sc->sc_omess[0] = MSG_MESSAGE_REJECT;
			break;
		default:
			/*
			 * We normally do not get here, since the chip
			 * automatically turns off ATN before the last
			 * byte of a message is sent to the target.
			 * However, if the target rejects our (multi-byte)
			 * message early by switching to MSG IN phase
			 * ATN remains on, so the target may return to
			 * MSG OUT phase. If there are no scheduled messages
			 * left we send a NO-OP.
			 *
			 * XXX - Note that this leaves no useful purpose for
			 * the NCR_ATN flag.
			 */
			sc->sc_flags &= ~NCR_ATN;
			sc->sc_omess[0] = MSG_NOOP;
			break;
		}
		sc->sc_omp = sc->sc_omess;
	}

#ifdef DEBUG
	if (ncr53c9x_debug & NCR_SHOWMSGS) {
		int i;

		NCR_MSGS(("<msgout:"));
		for (i = 0; i < sc->sc_omlen; i++)
			NCR_MSGS((" %02x", sc->sc_omess[i]));
		NCR_MSGS(("> "));
	}
#endif
	if (sc->sc_rev == NCR_VARIANT_FAS366) {
		/*
		 * XXX fifo size
		 */
		ncr53c9x_flushfifo(sc);
		ncr53c9x_wrfifo(sc, sc->sc_omp, sc->sc_omlen);
		sc->sc_cmdlen = 0;
		NCRCMD(sc, NCRCMD_TRANS);
	} else {
		/* (re)send the message */
		size = uimin(sc->sc_omlen, sc->sc_maxxfer);
		NCRDMA_SETUP(sc, &sc->sc_omp, &sc->sc_omlen, 0, &size);
		/* Program the SCSI counter */
		NCR_SET_COUNT(sc, size);

		/* Load the count in and start the message-out transfer */
		NCRCMD(sc, NCRCMD_NOP | NCRCMD_DMA);
		NCRCMD(sc, NCRCMD_TRANS | NCRCMD_DMA);
		NCRDMA_GO(sc);
	}
}

/*
 * This is the most critical part of the driver, and has to know
 * how to deal with *all* error conditions and phases from the SCSI
 * bus. If there are no errors and the DMA was active, then call the
 * DMA pseudo-interrupt handler. If this returns 1, then that was it
 * and we can return from here without further processing.
 *
 * Most of this needs verifying.
 */
int
ncr53c9x_intr(void *arg)
{
	struct ncr53c9x_softc *sc = arg;
	struct ncr53c9x_ecb *ecb;
	struct scsipi_periph *periph;
	struct ncr53c9x_tinfo *ti;
	size_t size;
	int nfifo;

	NCR_INTS(("[ncr53c9x_intr: state %d]", sc->sc_state));

	if (!NCRDMA_ISINTR(sc))
		return 0;

	mutex_enter(&sc->sc_lock);
again:
	/* and what do the registers say... */
	ncr53c9x_readregs(sc);

	sc->sc_intrcnt.ev_count++;

	/*
	 * At the moment, only a SCSI Bus Reset or Illegal
	 * Command are classed as errors. A disconnect is a
	 * valid condition, and we let the code check is the
	 * "NCR_BUSFREE_OK" flag was set before declaring it
	 * and error.
	 *
	 * Also, the status register tells us about "Gross
	 * Errors" and "Parity errors". Only the Gross Error
	 * is really bad, and the parity errors are dealt
	 * with later
	 *
	 * TODO
	 *	If there are too many parity error, go to slow
	 *	cable mode ?
	 */

	/* SCSI Reset */
	if ((sc->sc_espintr & NCRINTR_SBR) != 0) {
		if ((NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF) != 0) {
			NCRCMD(sc, NCRCMD_FLUSH);
			DELAY(1);
		}
		if (sc->sc_state != NCR_SBR) {
			printf("%s: SCSI bus reset\n",
			    device_xname(sc->sc_dev));
			ncr53c9x_init(sc, 0); /* Restart everything */
			goto out;
		}
#if 0
/*XXX*/		printf("<expected bus reset: "
		    "[intr %x, stat %x, step %d]>\n",
		    sc->sc_espintr, sc->sc_espstat, sc->sc_espstep);
#endif
		if (sc->sc_nexus != NULL)
			panic("%s: nexus in reset state",
			    device_xname(sc->sc_dev));
		goto sched;
	}

	ecb = sc->sc_nexus;

#define NCRINTR_ERR (NCRINTR_SBR|NCRINTR_ILL)
	if (sc->sc_espintr & NCRINTR_ERR ||
	    sc->sc_espstat & NCRSTAT_GE) {

		if ((sc->sc_espstat & NCRSTAT_GE) != 0) {
			/* Gross Error; no target ? */
			if (NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF) {
				NCRCMD(sc, NCRCMD_FLUSH);
				DELAY(1);
			}
			if (sc->sc_state == NCR_CONNECTED ||
			    sc->sc_state == NCR_SELECTING) {
				ecb->xs->error = XS_TIMEOUT;
				ncr53c9x_done(sc, ecb);
			}
			goto out;
		}

		if ((sc->sc_espintr & NCRINTR_ILL) != 0) {
			if ((sc->sc_flags & NCR_EXPECT_ILLCMD) != 0) {
				/*
				 * Eat away "Illegal command" interrupt
				 * on a ESP100 caused by a re-selection
				 * while we were trying to select
				 * another target.
				 */
#ifdef NCR53C9X_DEBUG
				printf("%s: ESP100 work-around activated\n",
					device_xname(sc->sc_dev));
#endif
				sc->sc_flags &= ~NCR_EXPECT_ILLCMD;
				goto out;
			}
			/* illegal command, out of sync ? */
			printf("%s: illegal command: 0x%x "
			    "(state %d, phase %x, prevphase %x)\n",
			    device_xname(sc->sc_dev), sc->sc_lastcmd,
			    sc->sc_state, sc->sc_phase, sc->sc_prevphase);
			if (NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF) {
				NCRCMD(sc, NCRCMD_FLUSH);
				DELAY(1);
			}
			ncr53c9x_init(sc, 1); /* Restart everything */
			goto out;
		}
	}
	sc->sc_flags &= ~NCR_EXPECT_ILLCMD;

	/*
	 * Call if DMA is active.
	 *
	 * If DMA_INTR returns true, then maybe go 'round the loop
	 * again in case there is no more DMA queued, but a phase
	 * change is expected.
	 */
	if (NCRDMA_ISACTIVE(sc)) {
		int r = NCRDMA_INTR(sc);
		if (r == -1) {
			printf("%s: DMA error; resetting\n",
			    device_xname(sc->sc_dev));
			ncr53c9x_init(sc, 1);
			goto out;
		}
		/* If DMA active here, then go back to work... */
		if (NCRDMA_ISACTIVE(sc))
			goto out;

		if ((sc->sc_espstat & NCRSTAT_TC) == 0) {
			/*
			 * DMA not completed.  If we can not find a
			 * acceptable explanation, print a diagnostic.
			 */
			if (sc->sc_state == NCR_SELECTING)
				/*
				 * This can happen if we are reselected
				 * while using DMA to select a target.
				 */
				/*void*/;
			else if (sc->sc_prevphase == MESSAGE_OUT_PHASE) {
				/*
				 * Our (multi-byte) message (eg SDTR) was
				 * interrupted by the target to send
				 * a MSG REJECT.
				 * Print diagnostic if current phase
				 * is not MESSAGE IN.
				 */
				if (sc->sc_phase != MESSAGE_IN_PHASE)
					printf("%s: !TC on MSG OUT"
					    " [intr %x, stat %x, step %d]"
					    " prevphase %x, resid %lx\n",
					    device_xname(sc->sc_dev),
					    sc->sc_espintr,
					    sc->sc_espstat,
					    sc->sc_espstep,
					    sc->sc_prevphase,
					    (u_long)sc->sc_omlen);
			} else if (sc->sc_dleft == 0) {
				/*
				 * The DMA operation was started for
				 * a DATA transfer. Print a diagnostic
				 * if the DMA counter and TC bit
				 * appear to be out of sync.
				 */
				printf("%s: !TC on DATA XFER"
				    " [intr %x, stat %x, step %d]"
				    " prevphase %x, resid %x\n",
				    device_xname(sc->sc_dev),
				    sc->sc_espintr,
				    sc->sc_espstat,
				    sc->sc_espstep,
				    sc->sc_prevphase,
				    ecb ? ecb->dleft : -1);
			}
		}
	}

	/*
	 * Check for less serious errors.
	 */
	if ((sc->sc_espstat & NCRSTAT_PE) != 0) {
		printf("%s: SCSI bus parity error\n", device_xname(sc->sc_dev));
		if (sc->sc_prevphase == MESSAGE_IN_PHASE)
			ncr53c9x_sched_msgout(SEND_PARITY_ERROR);
		else
			ncr53c9x_sched_msgout(SEND_INIT_DET_ERR);
	}

	if ((sc->sc_espintr & NCRINTR_DIS) != 0) {
		sc->sc_msgify = 0;
		NCR_INTS(("<DISC [intr %x, stat %x, step %d]>",
		    sc->sc_espintr,sc->sc_espstat,sc->sc_espstep));
		if (NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF) {
			NCRCMD(sc, NCRCMD_FLUSH);
#if 0
			DELAY(1);
#endif
		}
		/*
		 * This command must (apparently) be issued within
		 * 250mS of a disconnect. So here you are...
		 */
		NCRCMD(sc, NCRCMD_ENSEL);

		switch (sc->sc_state) {
		case NCR_RESELECTED:
			goto sched;

		case NCR_SELECTING:
		{
			struct ncr53c9x_linfo *li;

			ecb->xs->error = XS_SELTIMEOUT;

			/* Selection timeout -- discard all LUNs if empty */
			periph = ecb->xs->xs_periph;
			ti = &sc->sc_tinfo[periph->periph_target];
			li = LIST_FIRST(&ti->luns);
			while (li != NULL) {
				if (li->untagged == NULL && li->used == 0) {
					if (li->lun < NCR_NLUN)
						ti->lun[li->lun] = NULL;
					LIST_REMOVE(li, link);
					free(li, M_DEVBUF);
					/*
					 * Restart the search at the beginning
					 */
					li = LIST_FIRST(&ti->luns);
					continue;
				}
				li = LIST_NEXT(li, link);
			}
			goto finish;
		}
		case NCR_CONNECTED:
			if ((sc->sc_flags & NCR_SYNCHNEGO) != 0) {
#ifdef NCR53C9X_DEBUG
				if (ecb != NULL)
					scsipi_printaddr(ecb->xs->xs_periph);
				printf("sync nego not completed!\n");
#endif
				ti = &sc->sc_tinfo[
				    ecb->xs->xs_periph->periph_target];
				sc->sc_flags &= ~NCR_SYNCHNEGO;
				ti->flags &= ~(T_NEGOTIATE | T_SYNCMODE);
			}

			/* it may be OK to disconnect */
			if ((sc->sc_flags & NCR_ABORTING) == 0) {
				/*
				 * Section 5.1.1 of the SCSI 2 spec
				 * suggests issuing a REQUEST SENSE
				 * following an unexpected disconnect.
				 * Some devices go into a contingent
				 * allegiance condition when
				 * disconnecting, and this is necessary
				 * to clean up their state.
				 */
				printf("%s: unexpected disconnect "
			"[state %d, intr %x, stat %x, phase(c %x, p %x)]; ",
					device_xname(sc->sc_dev), sc->sc_state,
					sc->sc_espintr, sc->sc_espstat,
					sc->sc_phase, sc->sc_prevphase);

				if ((ecb->flags & ECB_SENSE) != 0) {
					printf("resetting\n");
					goto reset;
				}
				printf("sending REQUEST SENSE\n");
				callout_stop(&ecb->xs->xs_callout);
				ncr53c9x_sense(sc, ecb);
				goto out;
			}

			ecb->xs->error = XS_TIMEOUT;
			goto finish;

		case NCR_DISCONNECT:
			sc->sc_nexus = NULL;
			goto sched;

		case NCR_CMDCOMPLETE:
			goto finish;
		}
	}

	switch (sc->sc_state) {

	case NCR_SBR:
		printf("%s: waiting for SCSI Bus Reset to happen\n",
		    device_xname(sc->sc_dev));
		goto out;

	case NCR_RESELECTED:
		/*
		 * we must be continuing a message ?
		 */
		printf("%s: unhandled reselect continuation, "
		    "state %d, intr %02x\n",
		    device_xname(sc->sc_dev), sc->sc_state, sc->sc_espintr);
		ncr53c9x_init(sc, 1);
		goto out;

	case NCR_IDENTIFIED:
		ecb = sc->sc_nexus;
		if (sc->sc_phase != MESSAGE_IN_PHASE) {
			int i = (NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF);
			/*
			 * Things are seriously screwed up.
			 * Pull the brakes, i.e. reset
			 */
			printf("%s: target didn't send tag: %d bytes in fifo\n",
			    device_xname(sc->sc_dev), i);
			/* Drain and display fifo */
			while (i-- > 0)
				printf("[%d] ", NCR_READ_REG(sc, NCR_FIFO));

			ncr53c9x_init(sc, 1);
			goto out;
		} else
			goto msgin;

	case NCR_IDLE:
	case NCR_SELECTING:
		ecb = sc->sc_nexus;
		if (sc->sc_espintr & NCRINTR_RESEL) {
			sc->sc_msgpriq = sc->sc_msgout = sc->sc_msgoutq = 0;
			sc->sc_flags = 0;
			/*
			 * If we're trying to select a
			 * target ourselves, push our command
			 * back into the ready list.
			 */
			if (sc->sc_state == NCR_SELECTING) {
				NCR_INTS(("backoff selector "));
				callout_stop(&ecb->xs->xs_callout);
				ncr53c9x_dequeue(sc, ecb);
				TAILQ_INSERT_HEAD(&sc->ready_list, ecb, chain);
				ecb->flags |= ECB_READY;
				ecb = sc->sc_nexus = NULL;
			}
			sc->sc_state = NCR_RESELECTED;
			if (sc->sc_phase != MESSAGE_IN_PHASE) {
				/*
				 * Things are seriously screwed up.
				 * Pull the brakes, i.e. reset
				 */
				printf("%s: target didn't identify\n",
				    device_xname(sc->sc_dev));
				ncr53c9x_init(sc, 1);
				goto out;
			}
			/*
			 * The C90 only inhibits FIFO writes until reselection
			 * is complete, instead of waiting until the interrupt
			 * status register has been read.  So, if the reselect
			 * happens while we were entering command bytes (for
			 * another target) some of those bytes can appear in
			 * the FIFO here, after the interrupt is taken.
			 *
			 * To remedy this situation, pull the Selection ID
			 * and Identify message from the FIFO directly, and
			 * ignore any extraneous fifo contents. Also, set
			 * a flag that allows one Illegal Command Interrupt
			 * to occur which the chip also generates as a result
			 * of writing to the FIFO during a reselect.
			 */
			if (sc->sc_rev == NCR_VARIANT_ESP100) {
				nfifo = NCR_READ_REG(sc, NCR_FFLAG) &
				    NCRFIFO_FF;
				sc->sc_imess[0] = NCR_READ_REG(sc, NCR_FIFO);
				sc->sc_imess[1] = NCR_READ_REG(sc, NCR_FIFO);
				sc->sc_imlen = 2;
				if (nfifo != 2) {
					/* Flush the rest */
					NCRCMD(sc, NCRCMD_FLUSH);
				}
				sc->sc_flags |= NCR_EXPECT_ILLCMD;
				if (nfifo > 2)
					nfifo = 2; /* We fixed it.. */
			} else
				nfifo = ncr53c9x_rdfifo(sc, NCR_RDFIFO_START);

			if (nfifo != 2) {
				printf("%s: RESELECT: %d bytes in FIFO! "
				    "[intr %x, stat %x, step %d, "
				    "prevphase %x]\n",
				    device_xname(sc->sc_dev),
				    nfifo,
				    sc->sc_espintr,
				    sc->sc_espstat,
				    sc->sc_espstep,
				    sc->sc_prevphase);
				ncr53c9x_init(sc, 1);
				goto out;
			}
			sc->sc_selid = sc->sc_imess[0];
			NCR_INTS(("selid=%02x ", sc->sc_selid));

			/* Handle identify message */
			ncr53c9x_msgin(sc);

			if (sc->sc_state != NCR_CONNECTED &&
			    sc->sc_state != NCR_IDENTIFIED) {
				/* IDENTIFY fail?! */
				printf("%s: identify failed, "
				    "state %d, intr %02x\n",
				    device_xname(sc->sc_dev),
				    sc->sc_state, sc->sc_espintr);
				ncr53c9x_init(sc, 1);
				goto out;
			}
			goto shortcut; /* ie. next phase expected soon */
		}

#define	NCRINTR_DONE	(NCRINTR_FC | NCRINTR_BS)
		if ((sc->sc_espintr & NCRINTR_DONE) == NCRINTR_DONE) {
			/*
			 * Arbitration won; examine the `step' register
			 * to determine how far the selection could progress.
			 */
			ecb = sc->sc_nexus;
			if (ecb == NULL)
				panic("%s: no nexus", __func__);

			periph = ecb->xs->xs_periph;
			ti = &sc->sc_tinfo[periph->periph_target];

			switch (sc->sc_espstep) {
			case 0:
				/*
				 * The target did not respond with a
				 * message out phase - probably an old
				 * device that doesn't recognize ATN.
				 * Clear ATN and just continue, the
				 * target should be in the command
				 * phase.
				 * XXXX check for command phase?
				 */
				NCRCMD(sc, NCRCMD_RSTATN);
				break;
			case 1:
				if ((ti->flags & T_NEGOTIATE) == 0 &&
				    ecb->tag[0] == 0) {
					printf("%s: step 1 & !NEG\n",
					    device_xname(sc->sc_dev));
					goto reset;
				}
				if (sc->sc_phase != MESSAGE_OUT_PHASE) {
					printf("%s: !MSGOUT\n",
					    device_xname(sc->sc_dev));
					goto reset;
				}
				if (ti->flags & T_WIDE) {
					ti->flags |= T_WDTRSENT;
					ncr53c9x_sched_msgout(SEND_WDTR);
				}
				if (ti->flags & T_NEGOTIATE) {
					/* Start negotiating */
					ti->period = sc->sc_minsync;
					ti->offset = 15;
					sc->sc_flags |= NCR_SYNCHNEGO;
					if (ecb->tag[0])
						ncr53c9x_sched_msgout(
						    SEND_TAG | SEND_SDTR);
					else
						ncr53c9x_sched_msgout(
						    SEND_SDTR);
				} else {
					/* Could not do ATN3 so send TAG */
					ncr53c9x_sched_msgout(SEND_TAG);
				}
				sc->sc_prevphase = MESSAGE_OUT_PHASE; /* XXXX */
				break;
			case 3:
				/*
				 * Grr, this is supposed to mean
				 * "target left command phase  prematurely".
				 * It seems to happen regularly when
				 * sync mode is on.
				 * Look at FIFO to see if command went out.
				 * (Timing problems?)
				 */
				if (sc->sc_features & NCR_F_DMASELECT) {
					if (sc->sc_cmdlen == 0)
						/* Hope for the best.. */
						break;
				} else if ((NCR_READ_REG(sc, NCR_FFLAG)
				    & NCRFIFO_FF) == 0) {
					/* Hope for the best.. */
					break;
				}
				printf("(%s:%d:%d): selection failed;"
				    " %d left in FIFO "
				    "[intr %x, stat %x, step %d]\n",
				    device_xname(sc->sc_dev),
				    periph->periph_target,
				    periph->periph_lun,
				    NCR_READ_REG(sc, NCR_FFLAG)
				     & NCRFIFO_FF,
				    sc->sc_espintr, sc->sc_espstat,
				    sc->sc_espstep);
				NCRCMD(sc, NCRCMD_FLUSH);
				ncr53c9x_sched_msgout(SEND_ABORT);
				goto out;
			case 2:
				/* Select stuck at Command Phase */
				NCRCMD(sc, NCRCMD_FLUSH);
				break;
			case 4:
				if (sc->sc_features & NCR_F_DMASELECT &&
				    sc->sc_cmdlen != 0)
					printf("(%s:%d:%d): select; "
					    "%lu left in DMA buffer "
					    "[intr %x, stat %x, step %d]\n",
					    device_xname(sc->sc_dev),
					    periph->periph_target,
					    periph->periph_lun,
					    (u_long)sc->sc_cmdlen,
					    sc->sc_espintr,
					    sc->sc_espstat,
					    sc->sc_espstep);
				/* So far, everything went fine */
				break;
			}

			sc->sc_prevphase = INVALID_PHASE; /* ?? */
			/* Do an implicit RESTORE POINTERS. */
			sc->sc_dp = ecb->daddr;
			sc->sc_dleft = ecb->dleft;
			sc->sc_state = NCR_CONNECTED;
			break;

		} else {

			printf("%s: unexpected status after select"
			    ": [intr %x, stat %x, step %x]\n",
			    device_xname(sc->sc_dev),
			    sc->sc_espintr, sc->sc_espstat, sc->sc_espstep);
			NCRCMD(sc, NCRCMD_FLUSH);
			DELAY(1);
			goto reset;
		}
		if (sc->sc_state == NCR_IDLE) {
			printf("%s: stray interrupt\n",
			    device_xname(sc->sc_dev));
			mutex_exit(&sc->sc_lock);
			return 0;
		}
		break;

	case NCR_CONNECTED:
		if ((sc->sc_flags & NCR_ICCS) != 0) {
			/* "Initiate Command Complete Steps" in progress */
			uint8_t msg;

			sc->sc_flags &= ~NCR_ICCS;

			if ((sc->sc_espintr & NCRINTR_DONE) == 0) {
				printf("%s: ICCS: "
				    ": [intr %x, stat %x, step %x]\n",
				    device_xname(sc->sc_dev),
				    sc->sc_espintr, sc->sc_espstat,
				    sc->sc_espstep);
			}
			ncr53c9x_rdfifo(sc, NCR_RDFIFO_START);
			if (sc->sc_imlen < 2)
				printf("%s: can't get status, only %d bytes\n",
				    device_xname(sc->sc_dev),
				    (int)sc->sc_imlen);
			ecb->stat = sc->sc_imess[sc->sc_imlen - 2];
			msg = sc->sc_imess[sc->sc_imlen - 1];
			NCR_PHASE(("<stat:(%x,%x)>", ecb->stat, msg));
			if (msg == MSG_CMDCOMPLETE) {
				ecb->dleft = (ecb->flags & ECB_TENTATIVE_DONE)
				    ? 0 : sc->sc_dleft;
				if ((ecb->flags & ECB_SENSE) == 0)
					ecb->xs->resid = ecb->dleft;
				sc->sc_state = NCR_CMDCOMPLETE;
			} else
				printf("%s: STATUS_PHASE: msg %d\n",
				    device_xname(sc->sc_dev), msg);
			sc->sc_imlen = 0;
			NCRCMD(sc, NCRCMD_MSGOK);
			goto shortcut; /* ie. wait for disconnect */
		}
		break;

	default:
		printf("%s: invalid state: %d [intr %x, phase(c %x, p %x)]\n",
			device_xname(sc->sc_dev), sc->sc_state,
			sc->sc_espintr, sc->sc_phase, sc->sc_prevphase);
		goto reset;
	}

	/*
	 * Driver is now in state NCR_CONNECTED, i.e. we
	 * have a current command working the SCSI bus.
	 */
	if (sc->sc_state != NCR_CONNECTED || ecb == NULL) {
		panic("%s: no nexus", __func__);
	}

	switch (sc->sc_phase) {
	case MESSAGE_OUT_PHASE:
		NCR_PHASE(("MESSAGE_OUT_PHASE "));
		ncr53c9x_msgout(sc);
		sc->sc_prevphase = MESSAGE_OUT_PHASE;
		break;

	case MESSAGE_IN_PHASE:
msgin:
		NCR_PHASE(("MESSAGE_IN_PHASE "));
		if ((sc->sc_espintr & NCRINTR_BS) != 0) {
			if ((sc->sc_rev != NCR_VARIANT_FAS366) ||
			    (sc->sc_espstat2 & NCRFAS_STAT2_EMPTY) == 0) {
				NCRCMD(sc, NCRCMD_FLUSH);
			}
			sc->sc_flags |= NCR_WAITI;
			NCRCMD(sc, NCRCMD_TRANS);
		} else if ((sc->sc_espintr & NCRINTR_FC) != 0) {
			if ((sc->sc_flags & NCR_WAITI) == 0) {
				printf("%s: MSGIN: unexpected FC bit: "
				    "[intr %x, stat %x, step %x]\n",
				    device_xname(sc->sc_dev),
				    sc->sc_espintr, sc->sc_espstat,
				    sc->sc_espstep);
			}
			sc->sc_flags &= ~NCR_WAITI;
			ncr53c9x_rdfifo(sc,
			    (sc->sc_prevphase == sc->sc_phase) ?
			    NCR_RDFIFO_CONTINUE : NCR_RDFIFO_START);
			ncr53c9x_msgin(sc);
		} else {
			printf("%s: MSGIN: weird bits: "
			    "[intr %x, stat %x, step %x]\n",
			    device_xname(sc->sc_dev),
			    sc->sc_espintr, sc->sc_espstat, sc->sc_espstep);
		}
		sc->sc_prevphase = MESSAGE_IN_PHASE;
		goto shortcut;	/* i.e. expect data to be ready */

	case COMMAND_PHASE:
		/*
		 * Send the command block. Normally we don't see this
		 * phase because the SEL_ATN command takes care of
		 * all this. However, we end up here if either the
		 * target or we wanted to exchange some more messages
		 * first (e.g. to start negotiations).
		 */

		NCR_PHASE(("COMMAND_PHASE 0x%02x (%d) ",
		    ecb->cmd.cmd.opcode, ecb->clen));
		if (NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF) {
			NCRCMD(sc, NCRCMD_FLUSH);
#if 0
			DELAY(1);
#endif
		}
		if (sc->sc_features & NCR_F_DMASELECT) {
			/* setup DMA transfer for command */
			size = ecb->clen;
			sc->sc_cmdlen = size;
			sc->sc_cmdp = (void *)&ecb->cmd.cmd;
			NCRDMA_SETUP(sc, &sc->sc_cmdp, &sc->sc_cmdlen,
			    0, &size);
			/* Program the SCSI counter */
			NCR_SET_COUNT(sc, size);

			/* load the count in */
			NCRCMD(sc, NCRCMD_NOP | NCRCMD_DMA);

			/* start the command transfer */
			NCRCMD(sc, NCRCMD_TRANS | NCRCMD_DMA);
			NCRDMA_GO(sc);
		} else {
			ncr53c9x_wrfifo(sc, (uint8_t *)&ecb->cmd.cmd,
			    ecb->clen);
			sc->sc_cmdlen = 0;
			NCRCMD(sc, NCRCMD_TRANS);
		}
		sc->sc_prevphase = COMMAND_PHASE;
		break;

	case DATA_OUT_PHASE:
		NCR_PHASE(("DATA_OUT_PHASE [%ld] ",(long)sc->sc_dleft));
		NCRCMD(sc, NCRCMD_FLUSH);
		size = uimin(sc->sc_dleft, sc->sc_maxxfer);
		NCRDMA_SETUP(sc, &sc->sc_dp, &sc->sc_dleft, 0, &size);
		sc->sc_prevphase = DATA_OUT_PHASE;
		goto setup_xfer;

	case DATA_IN_PHASE:
		NCR_PHASE(("DATA_IN_PHASE "));
		if (sc->sc_rev == NCR_VARIANT_ESP100)
			NCRCMD(sc, NCRCMD_FLUSH);
		size = uimin(sc->sc_dleft, sc->sc_maxxfer);
		NCRDMA_SETUP(sc, &sc->sc_dp, &sc->sc_dleft, 1, &size);
		sc->sc_prevphase = DATA_IN_PHASE;
	setup_xfer:
		/* Target returned to data phase: wipe "done" memory */
		ecb->flags &= ~ECB_TENTATIVE_DONE;

		/* Program the SCSI counter */
		NCR_SET_COUNT(sc, size);

		/* load the count in */
		NCRCMD(sc, NCRCMD_NOP | NCRCMD_DMA);

		/*
		 * Note that if `size' is 0, we've already transceived
		 * all the bytes we want but we're still in DATA PHASE.
		 * Apparently, the device needs padding. Also, a
		 * transfer size of 0 means "maximum" to the chip
		 * DMA logic.
		 */
		NCRCMD(sc,
		    (size == 0 ? NCRCMD_TRPAD : NCRCMD_TRANS) | NCRCMD_DMA);
		NCRDMA_GO(sc);
		goto out;

	case STATUS_PHASE:
		NCR_PHASE(("STATUS_PHASE "));
		sc->sc_flags |= NCR_ICCS;
		NCRCMD(sc, NCRCMD_ICCS);
		sc->sc_prevphase = STATUS_PHASE;
		goto shortcut;	/* i.e. expect status results soon */

	case INVALID_PHASE:
		break;

	default:
		printf("%s: unexpected bus phase; resetting\n",
		    device_xname(sc->sc_dev));
		goto reset;
	}

out:
	mutex_exit(&sc->sc_lock);
	return 1;

reset:
	ncr53c9x_init(sc, 1);
	goto out;

finish:
	ncr53c9x_done(sc, ecb);
	goto out;

sched:
	sc->sc_state = NCR_IDLE;
	ncr53c9x_sched(sc);
	goto out;

shortcut:
	/*
	 * The idea is that many of the SCSI operations take very little
	 * time, and going away and getting interrupted is too high an
	 * overhead to pay. For example, selecting, sending a message
	 * and command and then doing some work can be done in one "pass".
	 *
	 * The delay is a heuristic. It is 2 when at 20MHz, 2 at 25MHz and 1
	 * at 40MHz. This needs testing.
	 */
	{
		struct timeval wait, cur;

		microtime(&wait);
		wait.tv_usec += 50 / sc->sc_freq;
		if (wait.tv_usec > 1000000) {
			wait.tv_sec++;
			wait.tv_usec -= 1000000;
		}
		do {
			if (NCRDMA_ISINTR(sc))
				goto again;
			microtime(&cur);
		} while (timercmp(&cur, &wait, <=));
	}
	goto out;
}

void
ncr53c9x_abort(struct ncr53c9x_softc *sc, struct ncr53c9x_ecb *ecb)
{

	/* 2 secs for the abort */
	ecb->timeout = NCR_ABORT_TIMEOUT;
	ecb->flags |= ECB_ABORT;

	if (ecb == sc->sc_nexus) {
		/*
		 * If we're still selecting, the message will be scheduled
		 * after selection is complete.
		 */
		if (sc->sc_state == NCR_CONNECTED)
			ncr53c9x_sched_msgout(SEND_ABORT);

		/*
		 * Reschedule timeout.
		 */
		callout_reset(&ecb->xs->xs_callout, mstohz(ecb->timeout),
		    ncr53c9x_timeout, ecb);
	} else {
		/*
		 * Just leave the command where it is.
		 * XXX - what choice do we have but to reset the SCSI
		 *	 eventually?
		 */
		if (sc->sc_state == NCR_IDLE)
			ncr53c9x_sched(sc);
	}
}

void
ncr53c9x_timeout(void *arg)
{
	struct ncr53c9x_ecb *ecb = arg;
	struct scsipi_xfer *xs = ecb->xs;
	struct scsipi_periph *periph = xs->xs_periph;
	struct ncr53c9x_softc *sc;
	struct ncr53c9x_tinfo *ti;

	sc = device_private(periph->periph_channel->chan_adapter->adapt_dev);
	ti = &sc->sc_tinfo[periph->periph_target];

	scsipi_printaddr(periph);
	printf("%s: timed out [ecb %p (flags 0x%x, dleft %x, stat %x)], "
	    "<state %d, nexus %p, phase(l %x, c %x, p %x), resid %lx, "
	    "msg(q %x,o %x) %s>",
	    device_xname(sc->sc_dev),
	    ecb, ecb->flags, ecb->dleft, ecb->stat,
	    sc->sc_state, sc->sc_nexus,
	    NCR_READ_REG(sc, NCR_STAT),
	    sc->sc_phase, sc->sc_prevphase,
	    (long)sc->sc_dleft, sc->sc_msgpriq, sc->sc_msgout,
	    NCRDMA_ISACTIVE(sc) ? "DMA active" : "");
#if NCR53C9X_DEBUG > 1
	printf("TRACE: %s.", ecb->trace);
#endif

	mutex_enter(&sc->sc_lock);

	if (ecb->flags & ECB_ABORT) {
		/* abort timed out */
		printf(" AGAIN\n");

		ncr53c9x_init(sc, 1);
	} else {
		/* abort the operation that has timed out */
		printf("\n");
		xs->error = XS_TIMEOUT;
		ncr53c9x_abort(sc, ecb);

		/* Disable sync mode if stuck in a data phase */
		if (ecb == sc->sc_nexus &&
		    (ti->flags & T_SYNCMODE) != 0 &&
		    (sc->sc_phase & (MSGI | CDI)) == 0) {
			/* XXX ASYNC CALLBACK! */
			scsipi_printaddr(periph);
			printf("sync negotiation disabled\n");
			sc->sc_cfflags |=
			    (1 << ((periph->periph_target & 7) + 8));
			ncr53c9x_update_xfer_mode(sc, periph->periph_target);
		}
	}

	mutex_exit(&sc->sc_lock);
}

void
ncr53c9x_watch(void *arg)
{
	struct ncr53c9x_softc *sc = arg;
	struct ncr53c9x_tinfo *ti;
	struct ncr53c9x_linfo *li;
	int t;
	/* Delete any structures that have not been used in 10min. */
	time_t old = time_second - (10 * 60);

	mutex_enter(&sc->sc_lock);
	for (t = 0; t < sc->sc_ntarg; t++) {
		ti = &sc->sc_tinfo[t];
		li = LIST_FIRST(&ti->luns);
		while (li) {
			if (li->last_used < old &&
			    li->untagged == NULL &&
			    li->used == 0) {
				if (li->lun < NCR_NLUN)
					ti->lun[li->lun] = NULL;
				LIST_REMOVE(li, link);
				free(li, M_DEVBUF);
				/* Restart the search at the beginning */
				li = LIST_FIRST(&ti->luns);
				continue;
			}
			li = LIST_NEXT(li, link);
		}
	}
	mutex_exit(&sc->sc_lock);
	callout_reset(&sc->sc_watchdog, 60 * hz, ncr53c9x_watch, sc);
}