xref: /src/sys/dev/ic/rtwreg.h

/*	$NetBSD: rtwreg.h,v 1.2 2004/12/19 08:19:25 dyoung Exp $	*/

/*
 * Copyright (c) 2003 The NetBSD Foundation, Inc.  All rights reserved.
 *
 * This code is derived from software contributed to The NetBSD Foundation
 * by David Young.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. Neither the name of the author nor the names of any co-contributors
 *    may be used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY David Young AND CONTRIBUTORS ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL David Young
 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
 * THE POSSIBILITY OF SUCH DAMAGE.
 */

/* Macros for bit twiddling. */
/* TBD factor w/ dev/ic/atwreg.h. */

#ifndef _BIT_TWIDDLE
#define _BIT_TWIDDLE
/* nth bit, BIT(0) == 0x1. */
#define BIT(n) (((n) == 32) ? 0 : ((u_int32_t)1 << (n)))

/* bits m through n, m < n. */
#define BITS(m, n) ((BIT(MAX((m), (n)) + 1) - 1) ^ (BIT(MIN((m), (n))) - 1))

/* find least significant bit that is set */
#define LOWEST_SET_BIT(x) ((((x) - 1) & (x)) ^ (x))

/* for x a power of two and p a non-negative integer, is x a greater
 * power than 2**p?
 */
#define GTEQ_POWER(x, p) (((u_long)(x) >> (p)) != 0)

#define MASK_TO_SHIFT2(m) (GTEQ_POWER(LOWEST_SET_BIT((m)), 1) ? 1 : 0)

#define MASK_TO_SHIFT4(m) \
	(GTEQ_POWER(LOWEST_SET_BIT((m)), 2) \
	    ? 2 + MASK_TO_SHIFT2((m) >> 2) \
	    : MASK_TO_SHIFT2((m)))

#define MASK_TO_SHIFT8(m) \
	(GTEQ_POWER(LOWEST_SET_BIT((m)), 4) \
	    ? 4 + MASK_TO_SHIFT4((m) >> 4) \
	    : MASK_TO_SHIFT4((m)))

#define MASK_TO_SHIFT16(m) \
	(GTEQ_POWER(LOWEST_SET_BIT((m)), 8) \
	    ? 8 + MASK_TO_SHIFT8((m) >> 8) \
	    : MASK_TO_SHIFT8((m)))

#define MASK_TO_SHIFT(m) \
	(GTEQ_POWER(LOWEST_SET_BIT((m)), 16) \
	    ? 16 + MASK_TO_SHIFT16((m) >> 16) \
	    : MASK_TO_SHIFT16((m)))

#define MASK_AND_RSHIFT(x, mask) (((x) & (mask)) >> MASK_TO_SHIFT(mask))
#define LSHIFT(x, mask) ((x) << MASK_TO_SHIFT(mask))
#define MASK_AND_REPLACE(reg, val, mask) ((reg & ~mask) | LSHIFT(val, mask))
#define PRESHIFT(m) MASK_AND_RSHIFT((m), (m))

#endif /* _BIT_TWIDDLE */

/* RTL8180L Host Control and Status Registers */

#define RTW_IDR0	0x00	/* ID Register: MAC addr, 6 bytes.
				 * Auto-loaded from EEPROM. Read by byte,
				 * by word, or by double word, but write
				 * only by double word.
				 */
#define RTW_IDR1	0x04

#define RTW_MAR0	0x08	/* Multicast filter, 64b. */
#define RTW_MAR1	0x0c

#define RTW_TSFTRL	0x18	/* Timing Synchronization Function Timer
				 * Register, low word, 32b, read-only.
				 */
#define RTW_TSFTRH	0x1c	/* High word, 32b, read-only. */
#define	RTW_TLPDA	0x20	/* Transmit Low Priority Descriptors Start
				 * Address, 32b, 256-byte alignment.
				 */
#define	RTW_TNPDA	0x24	/* Transmit Normal Priority Descriptors Start
				 * Address, 32b, 256-byte alignment.
				 */
#define	RTW_THPDA	0x28	/* Transmit High Priority Descriptors Start
				 * Address, 32b, 256-byte alignment.
				 */

#define RTW_BRSR	0x2c	/* Basic Rate Set Register, 16b */
#define	RTW_BRSR_BPLCP	BIT(8)	/* 1: use short PLCP header for CTS/ACK packet,
				 * 0: use long PLCP header
				 */
#define RTW_BRSR_MBR8180_MASK	BITS(1,0)	/* Maximum Basic Service Rate */
#define RTW_BRSR_MBR8180_1MBPS	LSHIFT(0, RTW_BRSR_MBR_MASK)
#define RTW_BRSR_MBR8180_2MBPS	LSHIFT(1, RTW_BRSR_MBR_MASK)
#define RTW_BRSR_MBR8180_5MBPS	LSHIFT(2, RTW_BRSR_MBR_MASK)
#define RTW_BRSR_MBR8180_11MBPS	LSHIFT(3, RTW_BRSR_MBR_MASK)

/* 8181 and 8180 docs conflict! */
#define RTW_BRSR_MBR8181_1MBPS	BIT(0)
#define RTW_BRSR_MBR8181_2MBPS	BIT(1)
#define RTW_BRSR_MBR8181_5MBPS	BIT(2)
#define RTW_BRSR_MBR8181_11MBPS	BIT(3)

/* BSSID, 6 bytes */
#define RTW_BSSID16	0x2e		/* first two bytes */
#define RTW_BSSID32	(0x2e + 4)	/* remaining four bytes */
#define RTW_BSSID0	RTW_BSSID16		/* BSSID[0], 8b */
#define RTW_BSSID1	(RTW_BSSID0 + 1)	/* BSSID[1], 8b */
#define RTW_BSSID2	(RTW_BSSID1 + 1)	/* BSSID[2], 8b */
#define RTW_BSSID3	(RTW_BSSID2 + 1)	/* BSSID[3], 8b */
#define RTW_BSSID4	(RTW_BSSID3 + 1)	/* BSSID[4], 8b */
#define RTW_BSSID5	(RTW_BSSID4 + 1)	/* BSSID[5], 8b */

#define	RTW_CR		0x37	/* Command Register, 8b */
#define	RTW_CR_RST	BIT(4)	/* Reset: host sets to 1 to disable
				 * transmitter & receiver, reinitialize FIFO.
				 * RTL8180L sets to 0 to signal completion.
				 */
#define	RTW_CR_RE	BIT(3)	/* Receiver Enable: host enables receiver
				 * by writing 1. RTL8180L indicates receiver
				 * is active with 1. After power-up, host
				 * must wait for reset before writing.
				 */
#define	RTW_CR_TE	BIT(2)	/* Transmitter Enable: host enables transmitter
				 * by writing 1. RTL8180L indicates transmitter
				 * is active with 1. After power-up, host
				 * must wait for reset before writing.
				 */
#define	RTW_CR_MULRW	BIT(0)	/* PCI Multiple Read/Write enable: 1 enables,
				 * 0 disables. XXX RTL8180, only?
				 */

#define	RTW_IMR		0x3c	/* Interrupt Mask Register, 16b */
#define	RTW_ISR		0x3e	/* Interrupt status register, 16b */

#define RTW_INTR_TXFOVW	BIT(15)		/* Tx FIFO Overflow */
#define RTW_INTR_TIMEOUT	BIT(14)	/* Time Out: 1 indicates
					 * RTW_TSFTR[0:31] = RTW_TINT
					 */
#define RTW_INTR_BCNINT	BIT(13)	/* Beacon Time Out: time for host to
				 * prepare beacon:
				 * RTW_TSFTR % (RTW_BCNITV_BCNITV * TU) =
				 * (RTW_BCNITV_BCNITV * TU - RTW_BINTRITV)
				 */
#define RTW_INTR_ATIMINT	BIT(12)
				/* ATIM Time Out: ATIM interval will pass,
				 * RTW_TSFTR % (RTW_BCNITV_BCNITV * TU) =
				 * (RTW_ATIMWND_ATIMWND * TU - RTW_ATIMTRITV)
				 */
#define RTW_INTR_TBDER	BIT(11)	/* Tx Beacon Descriptor Error:
				 * beacon transmission aborted because
				 * frame Rx'd
				 */
#define RTW_INTR_TBDOK	BIT(10)	/* Tx Beacon Descriptor OK */
#define RTW_INTR_THPDER	BIT(9)	/* Tx High Priority Descriptor Error:
				 * reached short/long retry limit
				 */
#define RTW_INTR_THPDOK	BIT(8)	/* Tx High Priority Descriptor OK */
#define RTW_INTR_TNPDER	BIT(7)	/* Tx Normal Priority Descriptor Error:
				 * reached short/long retry limit
				 */
#define RTW_INTR_TNPDOK	BIT(6)	/* Tx Normal Priority Descriptor OK */
#define RTW_INTR_RXFOVW	BIT(5)	/* Rx FIFO Overflow: either RDU (see below)
				 * or PCI bus too slow/busy
				 */
#define RTW_INTR_RDU	BIT(4)	/* Rx Descriptor Unavailable */
#define RTW_INTR_TLPDER	BIT(3)	/* Tx Normal Priority Descriptor Error
				 * reached short/long retry limit
				 */
#define RTW_INTR_TLPDOK	BIT(2)	/* Tx Normal Priority Descriptor OK */
#define RTW_INTR_RER	BIT(1)	/* Rx Error: CRC32 or ICV error */
#define RTW_INTR_ROK	BIT(0)	/* Rx OK */

/* Convenient interrupt conjunctions. */
#define RTW_INTR_RX	(RTW_INTR_RER|RTW_INTR_ROK)
#define RTW_INTR_TX	(RTW_INTR_TLPDER|RTW_INTR_TLPDOK|RTW_INTR_THPDER|\
			 RTW_INTR_THPDOK|RTW_INTR_TNPDER|RTW_INTR_TNPDOK)
#define RTW_INTR_BEACON	(RTW_INTR_TBDER|RTW_INTR_TBDOK|RTW_INTR_BCNINT)
#define RTW_INTR_IOERROR	(RTW_INTR_TXFOVW|RTW_INTR_RXFOVW|RTW_INTR_RDU)

#define	RTW_TCR		0x40	/* Transmit Configuration Register, 32b */
#define RTW_TCR_CWMIN	BIT(31)	/* 1: CWmin = 8, 0: CWmin = 32. */
#define RTW_TCR_SWSEQ	BIT(30)	/* 1: host assigns 802.11 sequence number,
				 * 0: hardware assigns sequence number
				 */
/* Hardware version ID, read-only */
#define RTW_TCR_HWVERID_MASK	BITS(29, 25)
#define RTW_TCR_HWVERID_D	LSHIFT(26, RTW_TCR_HWVERID_MASK)
#define RTW_TCR_HWVERID_F	LSHIFT(27, RTW_TCR_HWVERID_MASK)
#define RTW_TCR_HWVERID_RTL8180	RTW_TCR_HWVERID_F

/* Set ACK/CTS Timeout (EIFS).
 * 1: ACK rate = max(RTW_BRSR_MBR, Rx rate) (XXX not min? typo in datasheet?)
 * 0: ACK rate = 1Mbps
 */
#define RTW_TCR_SAT	BIT(24)
/* Max DMA Burst Size per Tx DMA Burst */
#define RTW_TCR_MXDMA_MASK	BITS(23,21)
#define RTW_TCR_MXDMA_16	LSHIFT(0, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_32	LSHIFT(1, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_64	LSHIFT(2, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_128	LSHIFT(3, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_256	LSHIFT(4, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_512	LSHIFT(5, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_1024	LSHIFT(6, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_2048	LSHIFT(7, RTW_TCR_MXDMA_MASK)

#define RTW_TCR_DISCW		BIT(20)	/* disable 802.11 random backoff */

#define RTW_TCR_ICV		BIT(19)	/* host lets RTL8180 append ICV to
					 * WEP packets
					 */

/* Loopback Test: disables TXI/TXQ outputs. */
#define RTW_TCR_LBK_MASK	BITS(18,17)
#define RTW_TCR_LBK_NORMAL	LSHIFT(0, RTW_TCR_LBK_MASK) /* normal ops */
#define RTW_TCR_LBK_MAC		LSHIFT(1, RTW_TCR_LBK_MASK) /* MAC loopback */
#define RTW_TCR_LBK_BBP		LSHIFT(2, RTW_TCR_LBK_MASK) /* baseband loop. */
#define RTW_TCR_LBK_CONT	LSHIFT(3, RTW_TCR_LBK_MASK) /* continuous Tx */

#define RTW_TCR_CRC	BIT(16)		/* host lets RTL8180 append CRC32 */
#define RTW_TCR_SRL_MASK	BITS(15,8)	/* Short Retry Limit */
#define RTW_TCR_LRL_MASK	BITS(7,0)	/* Long Retry Limit */

#define	RTW_RCR		0x44	/* Receive Configuration Register, 32b */
#define RTW_RCR_ONLYERLPKT	BIT(31)	/* only do Early Rx on packets
					 * longer than 1536 bytes
					 */
#define RTW_RCR_ENCS2		BIT(30)	/* enable carrier sense method 2 */
#define RTW_RCR_ENCS1		BIT(29)	/* enable carrier sense method 1 */
#define RTW_RCR_ENMARP		BIT(28)	/* enable MAC auto-reset PHY */
#define RTW_RCR_CBSSID		BIT(23)	/* Check BSSID/ToDS/FromDS: set
					 * "Link On" when received BSSID
					 * matches RTW_BSSID and received
					 * ToDS/FromDS are appropriate
					 * according to RTW_MSR_NETYPE.
					 */
#define RTW_RCR_APWRMGT		BIT(22)	/* accept packets w/ PWRMGMT bit set */
#define RTW_RCR_ADD3		BIT(21)	/* when RTW_MSR_NETYPE ==
					 * RTW_MSR_NETYPE_INFRA_OK, accept
					 * broadcast/multicast packets whose
					 * 3rd address matches RTL8180's MAC.
					 */
#define RTW_RCR_AMF		BIT(20)	/* accept management frames */
#define RTW_RCR_ACF		BIT(19)	/* accept control frames */
#define RTW_RCR_ADF		BIT(18)	/* accept data frames */
/* Rx FIFO Threshold: RTL8180 begins PCI transfer when this many data
 * bytes are received
 */
#define RTW_RCR_RXFTH_MASK	BITS(15,13)
#define RTW_RCR_RXFTH_64	LSHIFT(2, RTW_RCR_RXFTH_MASK)
#define RTW_RCR_RXFTH_128	LSHIFT(3, RTW_RCR_RXFTH_MASK)
#define RTW_RCR_RXFTH_256	LSHIFT(4, RTW_RCR_RXFTH_MASK)
#define RTW_RCR_RXFTH_512	LSHIFT(5, RTW_RCR_RXFTH_MASK)
#define RTW_RCR_RXFTH_1024	LSHIFT(6, RTW_RCR_RXFTH_MASK)
#define RTW_RCR_RXFTH_WHOLE	LSHIFT(7, RTW_RCR_RXFTH_MASK)

#define RTW_RCR_AICV		BIT(12)	/* accept frames w/ ICV errors */

/* Max DMA Burst Size per Rx DMA Burst */
#define RTW_RCR_MXDMA_MASK	BITS(10,8)
#define RTW_RCR_MXDMA_16	LSHIFT(0, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_32	LSHIFT(1, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_64	LSHIFT(2, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_128	LSHIFT(3, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_256	LSHIFT(4, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_512	LSHIFT(5, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_1024	LSHIFT(6, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_UNLIMITED	LSHIFT(7, RTW_RCR_MXDMA_MASK)

/* EEPROM type, read-only. 1: EEPROM is 93c56, 0: 93c46 */
#define RTW_RCR_9356SEL		BIT(6)

#define RTW_RCR_ACRC32		BIT(5)	/* accept frames w/ CRC32 errors */
#define RTW_RCR_AB		BIT(3)	/* accept broadcast frames */
#define RTW_RCR_AM		BIT(2)	/* accept multicast frames */
/* accept physical match frames. XXX means PLCP header ok? */
#define RTW_RCR_APM		BIT(1)
#define RTW_RCR_AAP		BIT(0)	/* accept frames w/ destination */

#define RTW_TINT	0x48	/* Timer Interrupt Register, 32b */
#define	RTW_TBDA	0x4c	/* Transmit Beacon Descriptor Start Address,
				 * 32b, 256-byte alignment
				 */
#define RTW_9346CR	0x50	/* 93c46/93c56 Command Register, 8b */
#define RTW_9346CR_EEM_MASK	BITS(7,6)	/* Operating Mode */
#define RTW_9346CR_EEM_NORMAL	LSHIFT(0, RTW_9346CR_EEM_MASK)
/* Load the EEPROM. Reset registers to defaults.
 * Takes ~2ms. RTL8180 indicates completion with RTW_9346CR_EEM_NORMAL.
 * XXX RTL8180 only?
 */
#define RTW_9346CR_EEM_AUTOLOAD	LSHIFT(1, RTW_9346CR_EEM_MASK)
/* Disable network & bus-master operations and enable
 * _EECS, _EESK, _EEDI, _EEDO.
 * XXX RTL8180 only?
 */
#define RTW_9346CR_EEM_PROGRAM	LSHIFT(2, RTW_9346CR_EEM_MASK)
/* Enable RTW_CONFIG[0123] registers. */
#define RTW_9346CR_EEM_CONFIG	LSHIFT(3, RTW_9346CR_EEM_MASK)
/* EEPROM pin status/control in _EEM_CONFIG, _EEM_AUTOLOAD modes.
 * XXX RTL8180 only?
 */
#define RTW_9346CR_EECS	BIT(3)
#define RTW_9346CR_EESK	BIT(2)
#define RTW_9346CR_EEDI	BIT(1)
#define RTW_9346CR_EEDO	BIT(0)	/* read-only */

#define RTW_CONFIG0	0x51	/* Configuration Register 0, 8b */
#define RTW_CONFIG0_WEP40	BIT(7)	/* implements 40-bit WEP,
					 * XXX RTL8180 only?
					 */
#define RTW_CONFIG0_WEP104	BIT(6)	/* implements 104-bit WEP,
					 * from EEPROM, read-only
					 * XXX RTL8180 only?
					 */
#define RTW_CONFIG0_LEDGPOEN	BIT(4)	/* 1: RTW_PSR_LEDGPO[01] control
					 *    LED[01] pins.
					 * 0: LED behavior defined by
					 *    RTW_CONFIG1_LEDS10_MASK
					 * XXX RTL8180 only?
					 */
/* auxiliary power is present, read-only */
#define RTW_CONFIG0_AUXPWR	BIT(3)
/* Geographic Location, read-only */
#define RTW_CONFIG0_GL_MASK		BITS(1,0)
/* _RTW_CONFIG0_GL_* is what the datasheet says, but RTW_CONFIG0_GL_*
 * work.
 */
#define _RTW_CONFIG0_GL_USA		LSHIFT(3, RTW_CONFIG0_GL_MASK)
#define RTW_CONFIG0_GL_EUROPE		LSHIFT(2, RTW_CONFIG0_GL_MASK)
#define RTW_CONFIG0_GL_JAPAN		LSHIFT(1, RTW_CONFIG0_GL_MASK)
#define RTW_CONFIG0_GL_USA		LSHIFT(0, RTW_CONFIG0_GL_MASK)
/* RTL8181 datasheet says RTW_CONFIG0_GL_JAPAN = 0. */

#define RTW_CONFIG1	0x52	/* Configuration Register 1, 8b */

/* LED configuration. From EEPROM. Read/write.
 *
 * Setting				LED0		LED1
 * -------				----		----
 * RTW_CONFIG1_LEDS_ACT_INFRA		Activity	Infrastructure
 * RTW_CONFIG1_LEDS_ACT_LINK		Activity	Link
 * RTW_CONFIG1_LEDS_TX_RX		Tx		Rx
 * RTW_CONFIG1_LEDS_LINKACT_INFRA	Link/Activity	Infrastructure
 */
#define RTW_CONFIG1_LEDS_MASK	BITS(7,6)
#define RTW_CONFIG1_LEDS_ACT_INFRA	LSHIFT(0, RTW_CONFIG1_LEDS_MASK)
#define RTW_CONFIG1_LEDS_ACT_LINK	LSHIFT(1, RTW_CONFIG1_LEDS_MASK)
#define RTW_CONFIG1_LEDS_TX_RX		LSHIFT(2, RTW_CONFIG1_LEDS_MASK)
#define RTW_CONFIG1_LEDS_LINKACT_INFRA	LSHIFT(3, RTW_CONFIG1_LEDS_MASK)

/* LWAKE Output Signal. Only applicable to Cardbus. Pulse width is 150ms.
 *
 *                                   RTW_CONFIG1_LWACT
 *				0			1
 * RTW_CONFIG4_LWPTN	0	active high		active low
 *			1	positive pulse		negative pulse
 */
#define RTW_CONFIG1_LWACT	BIT(4)

#define RTW_CONFIG1_MEMMAP	BIT(3)	/* using PCI memory space, read-only */
#define RTW_CONFIG1_IOMAP	BIT(2)	/* using PCI I/O space, read-only */
#define RTW_CONFIG1_VPD		BIT(1)	/* if set, VPD from offsets
					 * 0x40-0x7f in EEPROM are at
					 * registers 0x60-0x67 of PCI
					 * Configuration Space (XXX huh?)
					 */
#define RTW_CONFIG1_PMEN	BIT(0)	/* Power Management Enable: TBD */

#define RTW_CONFIG2	0x53	/* Configuration Register 2, 8b */
#define RTW_CONFIG2_LCK	BIT(7)	/* clocks are locked, read-only:
				 * Tx frequency & symbol clocks
				 * are derived from the same OSC
				 */
#define RTW_CONFIG2_ANT	BIT(6)	/* diversity enabled, read-only */
#define RTW_CONFIG2_DPS	BIT(3)	/* Descriptor Polling State: enable
				 * test mode.
				 */
#define RTW_CONFIG2_PAPESIGN		BIT(2)		/* TBD, from EEPROM */
#define RTW_CONFIG2_PAPETIME_MASK	BITS(1,0)	/* TBD, from EEPROM */

#define	RTW_ANAPARM	0x54	/* Analog parameter, 32b */
#define RTW_ANAPARM_RFPOW0_MASK	BITS(30,28)		/* undocumented bits
							 * which appear to
							 * control the power
							 * state of the RF
							 * components
							 */
#define RTW_ANAPARM_RFPOW0_RFMD_ON	LSHIFT(0x4, RTW_ANAPARM_RFPOW0_MASK)
/* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */
#define RTW_ANAPARM_RFPOW0_RFMD_SLEEP	LSHIFT(0x3, RTW_ANAPARM_RFPOW0_MASK)
/* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */
#define	RTW_ANAPARM_RFPOW0_RFMD_OFF	LSHIFT(0x3, RTW_ANAPARM_RFPOW0_MASK)

#define RTW_ANAPARM_RFPOW0_PHILIPS_ON	LSHIFT(0x3, RTW_ANAPARM_RFPOW0_MASK)
/* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */
#define RTW_ANAPARM_RFPOW0_PHILIPS_SLEEP\
    LSHIFT(0x3, RTW_ANAPARM_RFPOW0_MASK)
/* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */
#define RTW_ANAPARM_RFPOW0_PHILIPS_OFF\
    LSHIFT(0x3, RTW_ANAPARM_RFPOW0_MASK)

#define RTW_ANAPARM_TXDACOFF	BIT(27)			/* 1: disable Tx DAC,
							 * 0: enable
							 */
#define RTW_ANAPARM_RFPOW1_MASK	BITS(26,20)		/* undocumented bits
							 * which appear to
							 * control the power
							 * state of the RF
							 * components
							 */
#define RTW_ANAPARM_RFPOW1_RFMD_ON	LSHIFT(0x8, RTW_ANAPARM_RFPOW1_MASK)
#define RTW_ANAPARM_RFPOW1_RFMD_SLEEP	LSHIFT(0x78, RTW_ANAPARM_RFPOW1_MASK)
#define RTW_ANAPARM_RFPOW1_RFMD_OFF	LSHIFT(0x79, RTW_ANAPARM_RFPOW1_MASK)

#define RTW_ANAPARM_RFPOW1_PHILIPS_ON	LSHIFT(0x28, RTW_ANAPARM_RFPOW1_MASK)
#define RTW_ANAPARM_RFPOW1_PHILIPS_SLEEP\
    LSHIFT(0x78, RTW_ANAPARM_RFPOW1_MASK)
#define RTW_ANAPARM_RFPOW1_PHILIPS_OFF\
    LSHIFT(0x79, RTW_ANAPARM_RFPOW1_MASK)

#define RTW_ANAPARM_CARDSP_MASK	BITS(19,0)		/* undocumented
							 * card-specific
							 * bits from the
							 * EEPROM.
							 */

#define RTW_MSR		0x58	/* Media Status Register, 8b */
/* Network Type and Link Status */
#define RTW_MSR_NETYPE_MASK	BITS(3,2)
/* AP, XXX RTL8181 only? */
#define RTW_MSR_NETYPE_AP_OK	LSHIFT(3, RTW_MSR_NETYPE_MASK)
/* infrastructure link ok */
#define RTW_MSR_NETYPE_INFRA_OK	LSHIFT(2, RTW_MSR_NETYPE_MASK)
/* ad-hoc link ok */
#define RTW_MSR_NETYPE_ADHOC_OK	LSHIFT(1, RTW_MSR_NETYPE_MASK)
/* no link */
#define RTW_MSR_NETYPE_NOLINK	LSHIFT(0, RTW_MSR_NETYPE_MASK)

#define RTW_CONFIG3	0x59	/* Configuration Register 3, 8b */
#define RTW_CONFIG3_GNTSEL	BIT(7)	/* Grant Select, read-only */
#define RTW_CONFIG3_PARMEN	BIT(6)	/* Set RTW_CONFIG3_PARMEN and
					 * RTW_9346CR_EEM_CONFIG to
					 * allow RTW_ANAPARM writes.
					 */
#define RTW_CONFIG3_MAGIC	BIT(5)	/* Valid when RTW_CONFIG1_PMEN is
					 * set. If set, RTL8180 wakes up
					 * OS when Magic Packet is Rx'd.
					 */
#define RTW_CONFIG3_CARDBEN	BIT(3)	/* Cardbus-related registers
					 * and functions are enabled,
					 * read-only. XXX RTL8180 only.
					 */
#define RTW_CONFIG3_CLKRUNEN	BIT(2)	/* CLKRUN enabled, read-only.
					 * XXX RTL8180 only.
					 */
#define RTW_CONFIG3_FUNCREGEN	BIT(1)	/* Function Registers Enabled,
					 * read-only. XXX RTL8180 only.
					 */
#define RTW_CONFIG3_FBTBEN	BIT(0)	/* Fast back-to-back enabled,
					 * read-only.
					 */
#define RTW_CONFIG4	0x5A	/* Configuration Register 4, 8b */
#define RTW_CONFIG4_VCOPDN	BIT(7)	/* VCO Power Down
					 * 0: normal operation
					 *    (power-on default)
					 * 1: power-down VCO, RF front-end,
					 *    and most RTL8180 components.
					 */
#define RTW_CONFIG4_PWROFF	BIT(6)	/* Power Off
					 * 0: normal operation
					 *    (power-on default)
					 * 1: power-down RF front-end,
					 *    and most RTL8180 components,
					 *    but leave VCO on.
					 *
					 * XXX RFMD front-end only?
					 */
#define RTW_CONFIG4_PWRMGT	BIT(5)	/* Power Management
					 * 0: normal operation
					 *    (power-on default)
					 * 1: set Tx packet's PWRMGMT bit.
					 */
#define RTW_CONFIG4_LWPME	BIT(4)	/* LANWAKE vs. PMEB: Cardbus-only
					 * 0: LWAKE & PMEB asserted
					 *    simultaneously
					 * 1: LWAKE asserted only if
					 *    both PMEB is asserted and
					 *    ISOLATEB is low.
					 * XXX RTL8180 only.
					 */
#define RTW_CONFIG4_LWPTN	BIT(2)	/* see RTW_CONFIG1_LWACT
					 * XXX RTL8180 only.
					 */
/* Radio Front-End Programming Method */
#define RTW_CONFIG4_RFTYPE_MASK	BITS(1,0)
#define RTW_CONFIG4_RFTYPE_INTERSIL	LSHIFT(1, RTW_CONFIG4_RFTYPE_MASK)
#define RTW_CONFIG4_RFTYPE_RFMD		LSHIFT(2, RTW_CONFIG4_RFTYPE_MASK)
#define RTW_CONFIG4_RFTYPE_PHILIPS	LSHIFT(3, RTW_CONFIG4_RFTYPE_MASK)

#define RTW_TESTR	0x5B	/* TEST mode register, 8b */

#define RTW_PSR		0x5e	/* Page Select Register, 8b */
#define RTW_PSR_GPO	BIT(7)	/* Control/status of pin 52. */
#define RTW_PSR_GPI	BIT(6)	/* Status of pin 64. */
#define RTW_PSR_LEDGPO1	BIT(5)	/* Status/control of LED1 pin if
				 * RTW_CONFIG0_LEDGPOEN is set.
				 */
#define RTW_PSR_LEDGPO0	BIT(4)	/* Status/control of LED0 pin if
				 * RTW_CONFIG0_LEDGPOEN is set.
				 */
#define RTW_PSR_UWF	BIT(1)	/* Enable Unicast Wakeup Frame */
#define RTW_PSR_PSEN	BIT(0)	/* 1: page 1, 0: page 0 */

#define RTW_SCR		0x5f	/* Security Configuration Register, 8b */
#define RTW_SCR_KM_MASK	BITS(5,4)	/* Key Mode */
#define RTW_SCR_KM_WEP104	LSHIFT(1, RTW_SCR_KM_MASK)
#define RTW_SCR_KM_WEP40	LSHIFT(0, RTW_SCR_KM_MASK)
#define RTW_SCR_TXSECON		BIT(1)	/* Enable Tx WEP. Invalid if
					 * neither RTW_CONFIG0_WEP40 nor
					 * RTW_CONFIG0_WEP104 is set.
					 */
#define RTW_SCR_RXSECON		BIT(0)	/* Enable Rx WEP. Invalid if
					 * neither RTW_CONFIG0_WEP40 nor
					 * RTW_CONFIG0_WEP104 is set.
					 */

#define	RTW_BCNITV	0x70	/* Beacon Interval Register, 16b */
#define	RTW_BCNITV_BCNITV	BITS(9,0)	/* TU between TBTT, written
						 * by host.
						 */
#define	RTW_ATIMWND	0x72	/* ATIM Window Register, 16b */
#define	RTW_ATIMWND_ATIMWND	BITS(9,0)	/* ATIM Window length in TU,
						 * written by host.
						 */

#define RTW_BINTRITV	0x74	/* Beacon Interrupt Interval Register, 16b */
#define	RTW_BINTRITV_BINTRITV	BITS(9,0)	/* RTL8180 wakes host with
						 * RTW_INTR_BCNINT at BINTRITV
						 * microseconds before TBTT
						 */
#define RTW_ATIMTRITV	0x76	/* ATIM Interrupt Interval Register, 16b */
#define	RTW_ATIMTRITV_ATIMTRITV	BITS(9,0)	/* RTL8180 wakes host with
						 * RTW_INTR_ATIMINT at ATIMTRITV
						 * microseconds before end of
						 * ATIM Window
						 */

#define RTW_PHYDELAY	0x78	/* PHY Delay Register, 8b */
#define RTW_PHYDELAY_REVC_MAGIC	BIT(3)		/* Rev. C magic from reference
						 * driver
						 */
#define RTW_PHYDELAY_PHYDELAY	BITS(2,0)	/* microsecond Tx delay between
						 * MAC and RF front-end
						 */
#define RTW_CRCOUNT	0x79	/* Carrier Sense Counter, 8b */
#define	RTW_CRCOUNT_MAGIC	0x4c

#define RTW_CRC16ERR	0x7a	/* CRC16 error count, 16b, XXX RTL8181 only? */

#define RTW_BB	0x7c		/* Baseband interface, 32b */
/* used for writing RTL8180's integrated baseband processor */
#define RTW_BB_RD_MASK		BITS(23,16)	/* data to read */
#define RTW_BB_WR_MASK		BITS(15,8)	/* data to write */
#define RTW_BB_WREN		BIT(7)		/* write enable */
#define RTW_BB_ADDR_MASK	BITS(6,0)	/* address */

#define RTW_PHYADDR	0x7c	/* Address register for PHY interface, 8b */
#define RTW_PHYDATAW	0x7d	/* Write data to PHY, 8b, write-only */
#define RTW_PHYDATAR	0x7e	/* Read data from PHY, 8b (?), read-only */

#define RTW_PHYCFG	0x80	/* PHY Configuration Register, 32b */
#define RTW_PHYCFG_MAC_POLL	BIT(31)		/* if !RTW_PHYCFG_HST,
						 * host sets. MAC clears
						 * after banging bits.
						 */
#define	RTW_PHYCFG_HST		BIT(30)		/* 1: host bangs bits
						 * 0: MAC bangs bits
						 */
#define RTW_PHYCFG_MAC_RFTYPE_MASK	BITS(29,28)
#define RTW_PHYCFG_MAC_RFTYPE_INTERSIL	LSHIFT(0, RTW_PHYCFG_MAC_RFTYPE_MASK)
#define RTW_PHYCFG_MAC_RFTYPE_RFMD	LSHIFT(1, RTW_PHYCFG_MAC_RFTYPE_MASK)
#define RTW_PHYCFG_MAC_RFTYPE_GCT	RTW_PHYCFG_MAC_RFTYPE_RFMD
#define RTW_PHYCFG_MAC_RFTYPE_PHILIPS	LSHIFT(3, RTW_PHYCFG_MAC_RFTYPE_MASK)
#define RTW_PHYCFG_MAC_PHILIPS_ADDR_MASK	BITS(27,24)
#define RTW_PHYCFG_MAC_PHILIPS_DATA_MASK	BITS(23,0)
#define RTW_PHYCFG_MAC_MAXIM_LODATA_MASK	BITS(27,24)
#define RTW_PHYCFG_MAC_MAXIM_ADDR_MASK		BITS(11,8)
#define RTW_PHYCFG_MAC_MAXIM_HIDATA_MASK	BITS(7,0)
#define	RTW_PHYCFG_HST_EN		BIT(2)
#define	RTW_PHYCFG_HST_CLK		BIT(1)
#define	RTW_PHYCFG_HST_DATA		BIT(0)

#define	RTW_MAXIM_HIDATA_MASK			BITS(11,4)
#define	RTW_MAXIM_LODATA_MASK			BITS(3,0)

/**
 ** 0x84 - 0xD3, page 1, selected when RTW_PSR[PSEN] == 1.
 **/

#define	RTW_WAKEUP0L	0x84	/* Power Management Wakeup Frame */
#define	RTW_WAKEUP0H	0x88	/* 32b */

#define	RTW_WAKEUP1L	0x8c
#define	RTW_WAKEUP1H	0x90

#define	RTW_WAKEUP2LL	0x94
#define	RTW_WAKEUP2LH	0x98

#define	RTW_WAKEUP2HL	0x9c
#define	RTW_WAKEUP2HH	0xa0

#define	RTW_WAKEUP3LL	0xa4
#define	RTW_WAKEUP3LH	0xa8

#define	RTW_WAKEUP3HL	0xac
#define	RTW_WAKEUP3HH	0xb0

#define	RTW_WAKEUP4LL	0xb4
#define	RTW_WAKEUP4LH	0xb8

#define	RTW_WAKEUP4HL	0xbc
#define	RTW_WAKEUP4HH	0xc0

#define RTW_CRC0	0xc4	/* CRC of wakeup frame 0, 16b */
#define RTW_CRC1	0xc6	/* CRC of wakeup frame 1, 16b */
#define RTW_CRC2	0xc8	/* CRC of wakeup frame 2, 16b */
#define RTW_CRC3	0xca	/* CRC of wakeup frame 3, 16b */
#define RTW_CRC4	0xcc	/* CRC of wakeup frame 4, 16b */

/**
 ** 0x84 - 0xD3, page 0, selected when RTW_PSR[PSEN] == 0.
 **/

/* Default Key Registers, each 128b
 *
 * If RTW_SCR_KM_WEP104, 104 lsb are the key.
 * If RTW_SCR_KM_WEP40, 40 lsb are the key.
 */
#define RTW_DK0		0x90	/* Default Key 0 Register, 128b */
#define RTW_DK1		0xa0	/* Default Key 1 Register, 128b */
#define RTW_DK2		0xb0	/* Default Key 2 Register, 128b */
#define RTW_DK3		0xc0	/* Default Key 3 Register, 128b */

#define	RTW_CONFIG5	0xd8	/* Configuration Register 5, 8b */
#define RTW_CONFIG5_TXFIFOOK	BIT(7)	/* Tx FIFO self-test pass, read-only */
#define RTW_CONFIG5_RXFIFOOK	BIT(6)	/* Rx FIFO self-test pass, read-only */
#define RTW_CONFIG5_CALON	BIT(5)	/* 1: start calibration cycle
					 *    and raise AGCRESET pin.
					 * 0: lower AGCRESET pin
					 */
#define RTW_CONFIG5_EACPI	BIT(2)	/* Enable ACPI Wake up, default 0 */
#define RTW_CONFIG5_LANWAKE	BIT(1)	/* Enable LAN Wake signal,
					 * from EEPROM
					 */
#define RTW_CONFIG5_PMESTS	BIT(0)	/* 1: both software & PCI Reset
					 *    reset PME_Status
					 * 0: only software resets PME_Status
					 *
					 * From EEPROM.
					 */

#define	RTW_TPPOLL	0xd9	/* Transmit Priority Polling Register, 8b,
				 * write-only.
				 */
#define RTW_TPPOLL_BQ	BIT(7)	/* RTL8180 clears to notify host of a beacon
				 * Tx. Host writes have no effect.
				 */
#define RTW_TPPOLL_HPQ	BIT(6)	/* Host writes 1 to notify RTL8180 of
				 * high-priority Tx packets, RTL8180 clears
				 * to after high-priority Tx is complete.
				 */
#define RTW_TPPOLL_NPQ	BIT(5)	/* If RTW_CONFIG2_DPS is set,
				 * host writes 1 to notify RTL8180 of
				 * normal-priority Tx packets, RTL8180 clears
				 * after normal-priority Tx is complete.
				 *
				 * If RTW_CONFIG2_DPS is clear, host writes
				 * have no effect. RTL8180 clears after
				 * normal-priority Tx is complete.
				 */
#define RTW_TPPOLL_LPQ	BIT(4)	/* Host writes 1 to notify RTL8180 of
				 * low-priority Tx packets, RTL8180 clears
				 * after low-priority Tx is complete.
				 */
#define RTW_TPPOLL_SBQ	BIT(3)	/* Host writes 1 to tell RTL8180 to
				 * stop beacon DMA. This bit is invalid
				 * when RTW_CONFIG2_DPS is set.
				 */
#define RTW_TPPOLL_SHPQ	BIT(2)	/* Host writes 1 to tell RTL8180 to
				 * stop high-priority DMA.
				 */
#define RTW_TPPOLL_SNPQ	BIT(2)	/* Host writes 1 to tell RTL8180 to
				 * stop normal-priority DMA. This bit is invalid
				 * when RTW_CONFIG2_DPS is set.
				 */
#define RTW_TPPOLL_SLPQ	BIT(2)	/* Host writes 1 to tell RTL8180 to
				 * stop low-priority DMA.
				 */
#define RTW_TPPOLL_FSWINT	BIT(0)	/* Force software interrupt. From
				 	 * reference driver.
					 */


#define	RTW_CWR		0xdc	/* Contention Window Register, 16b, read-only */
/* Contention Window: indicates number of contention windows before Tx
 */
#define	RTW_CWR_CW	BITS(9,0)

/* Retry Count Register, 16b, read-only */
#define	RTW_RETRYCTR	0xde
/* Retry Count: indicates number of retries after Tx */
#define	RTW_RETRYCTR_RETRYCT	BITS(7,0)

#define RTW_RDSAR	0xe4	/* Receive descriptor Start Address Register,
				 * 32b, 256-byte alignment.
				 */
/* Function Event Register, 32b, Cardbus only. Only valid when
 * both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN are set.
 */
#define RTW_FER		0xf0
#define RTW_FER_INTR	BIT(15)	/* set when RTW_FFER_INTR is set */
#define RTW_FER_GWAKE	BIT(4)	/* General Wakeup */
/* Function Event Mask Register, 32b, Cardbus only. Only valid when
 * both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN are set.
 */
#define RTW_FEMR	0xf4
#define RTW_FEMR_INTR	BIT(15)	/* set when RTW_FFER_INTR is set */
#define RTW_FEMR_WKUP	BIT(14)	/* Wakeup Mask */
#define RTW_FEMR_GWAKE	BIT(4)	/* General Wakeup */
/* Function Present State Register, 32b, read-only, Cardbus only.
 * Only valid when both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN
 * are set.
 */
#define RTW_FPSR	0xf8
#define RTW_FPSR_INTR	BIT(15)	/* TBD */
#define RTW_FPSR_GWAKE	BIT(4)	/* General Wakeup: TBD */
/* Function Force Event Register, 32b, write-only, Cardbus only.
 * Only valid when both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN
 * are set.
 */
#define RTW_FFER	0xfc
#define RTW_FFER_INTR	BIT(15)	/* TBD */
#define RTW_FFER_GWAKE	BIT(4)	/* General Wakeup: TBD */

/* Serial EEPROM offsets */
#define RTW_SR_ID	0x00	/* 16b */
#define RTW_SR_VID	0x02	/* 16b */
#define RTW_SR_DID	0x04	/* 16b */
#define RTW_SR_SVID	0x06	/* 16b */
#define RTW_SR_SMID	0x08	/* 16b */
#define RTW_SR_MNGNT	0x0a
#define RTW_SR_MXLAT	0x0b
#define RTW_SR_RFCHIPID	0x0c
#define RTW_SR_CONFIG3	0x0d
#define RTW_SR_MAC	0x0e	/* 6 bytes */
#define RTW_SR_CONFIG0	0x14
#define RTW_SR_CONFIG1	0x15
#define RTW_SR_PMC	0x16	/* Power Management Capabilities, 16b */
#define RTW_SR_CONFIG2	0x18
#define RTW_SR_CONFIG4	0x19
#define RTW_SR_ANAPARM	0x1a	/* Analog Parameters, 32b */
#define RTW_SR_TESTR	0x1e
#define RTW_SR_CONFIG5	0x1f
#define RTW_SR_TXPOWER1		0x20
#define RTW_SR_TXPOWER2		0x21
#define RTW_SR_TXPOWER3		0x22
#define RTW_SR_TXPOWER4		0x23
#define RTW_SR_TXPOWER5		0x24
#define RTW_SR_TXPOWER6		0x25
#define RTW_SR_TXPOWER7		0x26
#define RTW_SR_TXPOWER8		0x27
#define RTW_SR_TXPOWER9		0x28
#define RTW_SR_TXPOWER10	0x29
#define RTW_SR_TXPOWER11	0x2a
#define RTW_SR_TXPOWER12	0x2b
#define RTW_SR_TXPOWER13	0x2c
#define RTW_SR_TXPOWER14	0x2d
#define RTW_SR_CHANNELPLAN	0x2e	/* bitmap of channels to scan */
#define RTW_SR_ENERGYDETTHR	0x2f	/* energy-detect threshold */
#define RTW_SR_ENERGYDETTHR_DEFAULT	0x0c	/* use this if old SROM */
#define RTW_SR_CISPOINTER	0x30	/* 16b */
#define RTW_SR_RFPARM		0x32	/* RF-specific parameter */
#define RTW_SR_RFPARM_DIGPHY	BIT(0)		/* 1: digital PHY */
#define RTW_SR_RFPARM_DFLANTB	BIT(1)		/* 1: antenna B is default */
#define RTW_SR_RFPARM_CS_MASK	BITS(2,3)	/* carrier-sense type */
#define RTW_SR_VERSION		0x3c	/* EEPROM content version, 16b */
#define RTW_SR_CRC		0x3e	/* EEPROM content CRC, 16b */
#define RTW_SR_VPD		0x40	/* Vital Product Data, 64 bytes */
#define RTW_SR_CIS		0x80	/* CIS Data, 93c56 only, 128 bytes*/

/*
 * RTL8180 Transmit/Receive Descriptors
 */

/* the first descriptor in each ring must be on a 256-byte boundary */
#define RTW_DESC_ALIGNMENT 256

/* Tx descriptor */
struct rtw_txdesc {
	u_int32_t	htx_ctl0;
	u_int32_t	htx_ctl1;
	u_int32_t	htx_buf;
	u_int32_t	htx_len;
	u_int32_t	htx_next;
	u_int32_t	htx_rsvd[3];
};

#define htx_stat htx_ctl0

#define RTW_TXCTL0_OWN			BIT(31)		/* 1: ready to Tx */
#define RTW_TXCTL0_RSVD0		BIT(30)		/* reserved */
#define RTW_TXCTL0_FS			BIT(29)		/* first segment */
#define RTW_TXCTL0_LS			BIT(28)		/* last segment */

#define RTW_TXCTL0_RATE_MASK		BITS(27,24)	/* Tx rate */
#define RTW_TXCTL0_RATE_1MBPS		LSHIFT(0, RTW_TXCTL0_RATE_MASK)
#define RTW_TXCTL0_RATE_2MBPS		LSHIFT(1, RTW_TXCTL0_RATE_MASK)
#define RTW_TXCTL0_RATE_5MBPS		LSHIFT(2, RTW_TXCTL0_RATE_MASK)
#define RTW_TXCTL0_RATE_11MBPS		LSHIFT(3, RTW_TXCTL0_RATE_MASK)

#define RTW_TXCTL0_RTSEN		BIT(23)		/* RTS Enable */

#define RTW_TXCTL0_RTSRATE_MASK		BITS(22,19)	/* Tx rate */
#define RTW_TXCTL0_RTSRATE_1MBPS	LSHIFT(0, RTW_TXCTL0_RTSRATE_MASK)
#define RTW_TXCTL0_RTSRATE_2MBPS	LSHIFT(1, RTW_TXCTL0_RTSRATE_MASK)
#define RTW_TXCTL0_RTSRATE_5MBPS	LSHIFT(2, RTW_TXCTL0_RTSRATE_MASK)
#define RTW_TXCTL0_RTSRATE_11MBPS	LSHIFT(3, RTW_TXCTL0_RTSRATE_MASK)

#define RTW_TXCTL0_BEACON		BIT(18)	/* packet is a beacon */
#define RTW_TXCTL0_MOREFRAG		BIT(17)	/* another fragment follows */
#define RTW_TXCTL0_SPLCP		BIT(16)	/* add short PLCP preamble
						 * and header
						 */
#define RTW_TXCTL0_KEYID_MASK		BITS(15,14)	/* default key id */
#define RTW_TXCTL0_RSVD1_MASK		BITS(13,12)	/* reserved */
#define RTW_TXCTL0_TPKTSIZE_MASK	BITS(11,0)	/* Tx packet size
							 * in bytes
							 */

#define RTW_TXSTAT_OWN		RTW_TXCTL0_OWN
#define RTW_TXSTAT_RSVD0	RTW_TXCTL0_RSVD0
#define RTW_TXSTAT_FS		RTW_TXCTL0_FS
#define RTW_TXSTAT_LS		RTW_TXCTL0_LS
#define RTW_TXSTAT_RSVD1_MASK	BITS(27,16)
#define RTW_TXSTAT_TOK		BIT(15)
#define RTW_TXSTAT_RTSRETRY_MASK	BITS(14,8)	/* RTS retry count */
#define RTW_TXSTAT_DRC_MASK		BITS(7,0)	/* Data retry count */

#define RTW_TXCTL1_LENGEXT	BIT(31)		/* supplements _LENGTH
						 * in packets sent 5.5Mb/s or
						 * faster
						 */
#define RTW_TXCTL1_LENGTH_MASK	BITS(30,16)	/* PLCP length (microseconds) */
#define RTW_TXCTL1_RTSDUR_MASK	BITS(15,0)	/* RTS Duration
						 * (microseconds)
						 */

#define RTW_TXLEN_LENGTH_MASK	BITS(11,0)	/* Tx buffer length in bytes */

/* Rx descriptor */
struct rtw_rxdesc {
    u_int32_t	hrx_ctl;
    u_int32_t	hrx_rsvd0;
    u_int32_t	hrx_buf;
    u_int32_t	hrx_rsvd1;
};

#define hrx_stat hrx_ctl
#define hrx_rssi hrx_rsvd0
#define hrx_tsftl hrx_buf	/* valid only when RTW_RXSTAT_LS is set */
#define hrx_tsfth hrx_rsvd1	/* valid only when RTW_RXSTAT_LS is set */

#define RTW_RXCTL_OWN		BIT(31)		/* 1: owned by NIC */
#define RTW_RXCTL_EOR		BIT(30)		/* end of ring */
#define RTW_RXCTL_FS		BIT(29)		/* first segment */
#define RTW_RXCTL_LS		BIT(28)		/* last segment */
#define RTW_RXCTL_RSVD0_MASK	BITS(29,12)	/* reserved */
#define RTW_RXCTL_LENGTH_MASK	BITS(11,0)	/* Rx buffer length */

#define RTW_RXSTAT_OWN		RTW_RXCTL_OWN
#define RTW_RXSTAT_EOR		RTW_RXCTL_EOR
#define RTW_RXSTAT_FS		RTW_RXCTL_FS	/* first segment */
#define RTW_RXSTAT_LS		RTW_RXCTL_LS	/* last segment */
#define RTW_RXSTAT_DMAFAIL	BIT(27)		/* DMA failure on this pkt */
#define RTW_RXSTAT_BOVF		BIT(26)		/* buffer overflow XXX means
						 * FIFO exhausted?
						 */
#define RTW_RXSTAT_SPLCP	BIT(25)		/* Rx'd with short preamble
						 * and PLCP header
						 */
#define RTW_RXSTAT_RSVD1	BIT(24)		/* reserved */
#define RTW_RXSTAT_RATE_MASK	BITS(23,20)	/* Rx rate */
#define RTW_RXSTAT_RATE_1MBPS	LSHIFT(0, RTW_RXSTAT_RATE_MASK)
#define RTW_RXSTAT_RATE_2MBPS	LSHIFT(1, RTW_RXSTAT_RATE_MASK)
#define RTW_RXSTAT_RATE_5MBPS	LSHIFT(2, RTW_RXSTAT_RATE_MASK)
#define RTW_RXSTAT_RATE_11MBPS	LSHIFT(3, RTW_RXSTAT_RATE_MASK)
#define RTW_RXSTAT_MIC		BIT(19)		/* XXX from reference driver */
#define RTW_RXSTAT_MAR		BIT(18)		/* is multicast */
#define RTW_RXSTAT_PAR		BIT(17)		/* matches RTL8180's MAC */
#define RTW_RXSTAT_BAR		BIT(16)		/* is broadcast */
#define RTW_RXSTAT_RES		BIT(15)		/* error summary. valid when
						 * RTW_RXSTAT_LS set. indicates
						 * that either RTW_RXSTAT_CRC32
						 * or RTW_RXSTAT_ICV is set.
						 */
#define RTW_RXSTAT_PWRMGT	BIT(14)		/* 802.11 PWRMGMT bit is set */
#define RTW_RXSTAT_CRC16	BIT(14)		/* XXX CRC16 error, from
						 * reference driver
						 */
#define RTW_RXSTAT_CRC32	BIT(13)		/* CRC32 error */
#define RTW_RXSTAT_ICV		BIT(12)		/* ICV error */
#define RTW_RXSTAT_LENGTH_MASK	BITS(11,0)	/* frame length, including
						 * CRC32
						 */

/* Convenient status conjunction. */
#define RTW_RXSTAT_ONESEG	(RTW_RXSTAT_FS|RTW_RXSTAT_LS)
/* Convenient status disjunctions. */
#define RTW_RXSTAT_IOERROR	(RTW_RXSTAT_DMAFAIL|RTW_RXSTAT_BOVF)
#define RTW_RXSTAT_DEBUG	(RTW_RXSTAT_SPLCP|RTW_RXSTAT_MAR|\
				 RTW_RXSTAT_PAR|RTW_RXSTAT_BAR|\
				 RTW_RXSTAT_PWRMGT|RTW_RXSTAT_CRC32|\
				 RTW_RXSTAT_ICV)


#define RTW_RXRSSI_VLAN		BITS(32,16)	/* XXX from reference driver */
/* for Philips RF front-ends */
#define RTW_RXRSSI_RSSI		BITS(15,8)	/* RF energy at the PHY */
/* for RF front-ends by Intersil, Maxim, RFMD */
#define RTW_RXRSSI_IMR_RSSI	BITS(15,9)	/* RF energy at the PHY */
#define RTW_RXRSSI_IMR_LNA	BIT(8)		/* 1: LNA activated */
#define RTW_RXRSSI_SQ		BITS(7,0)	/* Barker code-lock quality */

#define RTW_READ8(regs, ofs)						\
	bus_space_read_1((regs)->r_bt, (regs)->r_bh, (ofs))

#define RTW_READ16(regs, ofs)						\
	bus_space_read_2((regs)->r_bt, (regs)->r_bh, (ofs))

#define RTW_READ(regs, ofs)						\
	bus_space_read_4((regs)->r_bt, (regs)->r_bh, (ofs))

#define RTW_WRITE8(regs, ofs, val)					\
	bus_space_write_1((regs)->r_bt, (regs)->r_bh, (ofs), (val))

#define RTW_WRITE16(regs, ofs, val)					\
	bus_space_write_2((regs)->r_bt, (regs)->r_bh, (ofs), (val))

#define RTW_WRITE(regs, ofs, val)					\
	bus_space_write_4((regs)->r_bt, (regs)->r_bh, (ofs), (val))

#define	RTW_ISSET(regs, reg, mask)					\
	(RTW_READ((regs), (reg)) & (mask))

#define	RTW_CLR(regs, reg, mask)					\
	RTW_WRITE((regs), (reg), RTW_READ((regs), (reg)) & ~(mask))

/* bus_space(9) lied? */
#ifndef BUS_SPACE_BARRIER_SYNC
#define BUS_SPACE_BARRIER_SYNC (BUS_SPACE_BARRIER_READ|BUS_SPACE_BARRIER_WRITE)
#endif

#ifndef BUS_SPACE_BARRIER_READ_BEFORE_READ
#define BUS_SPACE_BARRIER_READ_BEFORE_READ BUS_SPACE_BARRIER_READ
#endif

#ifndef BUS_SPACE_BARRIER_READ_BEFORE_WRITE
#define BUS_SPACE_BARRIER_READ_BEFORE_WRITE BUS_SPACE_BARRIER_READ
#endif

#ifndef BUS_SPACE_BARRIER_WRITE_BEFORE_READ
#define BUS_SPACE_BARRIER_WRITE_BEFORE_READ BUS_SPACE_BARRIER_WRITE
#endif

#ifndef BUS_SPACE_BARRIER_WRITE_BEFORE_WRITE
#define BUS_SPACE_BARRIER_WRITE_BEFORE_WRITE BUS_SPACE_BARRIER_WRITE
#endif

/*
 * Bus barrier
 *
 * Complete outstanding read and/or write ops on [reg0, reg1]
 * ([reg1, reg0]) before starting new ops on the same region. See
 * acceptable bus_space_barrier(9) for the flag definitions.
 */
#define RTW_BARRIER(regs, reg0, reg1, flags)			\
	bus_space_barrier((regs)->r_bh, (regs)->r_bt,		\
	    MIN(reg0, reg1), MAX(reg0, reg1) - MIN(reg0, reg1) + 4, flags)

/*
 * Barrier convenience macros.
 */
/* sync */
#define RTW_SYNC(regs, reg0, reg1)				\
	RTW_BARRIER(regs, reg0, reg1, BUS_SPACE_BARRIER_SYNC)

/* write-before-write */
#define RTW_WBW(regs, reg0, reg1)				\
	RTW_BARRIER(regs, reg0, reg1, BUS_SPACE_BARRIER_WRITE_BEFORE_WRITE)

/* write-before-read */
#define RTW_WBR(regs, reg0, reg1)				\
	RTW_BARRIER(regs, reg0, reg1, BUS_SPACE_BARRIER_WRITE_BEFORE_READ)

/* read-before-read */
#define RTW_RBR(regs, reg0, reg1)				\
	RTW_BARRIER(regs, reg0, reg1, BUS_SPACE_BARRIER_READ_BEFORE_READ)

/* read-before-read */
#define RTW_RBW(regs, reg0, reg1)				\
	RTW_BARRIER(regs, reg0, reg1, BUS_SPACE_BARRIER_READ_BEFORE_WRITE)

#define RTW_WBRW(regs, reg0, reg1)				\
		RTW_BARRIER(regs, reg0, reg1,			\
		    BUS_SPACE_BARRIER_WRITE_BEFORE_READ |	\
		    BUS_SPACE_BARRIER_WRITE_BEFORE_WRITE)

/*
 * Registers for RTL8180L's built-in baseband modem.
 */
#define RTW_BBP_SYS1		0x00
#define RTW_BBP_TXAGC		0x03
#define RTW_BBP_LNADET		0x04
#define RTW_BBP_IFAGCINI	0x05
#define RTW_BBP_IFAGCLIMIT	0x06
#define RTW_BBP_IFAGCDET	0x07

#define RTW_BBP_ANTATTEN	0x10
#define RTW_BBP_ANTATTEN_PHILIPS_MAGIC		0x91
#define RTW_BBP_ANTATTEN_INTERSIL_MAGIC		0x92
#define RTW_BBP_ANTATTEN_RFMD_MAGIC		0x93
#define RTW_BBP_ANTATTEN_MAXIM_MAGIC		0xb3
#define	RTW_BBP_ANTATTEN_DFLANTB		0x40
#define	RTW_BBP_ANTATTEN_CHAN14			0x0c

#define RTW_BBP_TRL			0x11
#define RTW_BBP_SYS2			0x12
#define RTW_BBP_SYS2_ANTDIV		0x80	/* enable antenna diversity */
#define RTW_BBP_SYS2_RATE_MASK		BITS(5,4)	/* loopback rate?
							 * 0: 1Mbps
							 * 1: 2Mbps
							 * 2: 5.5Mbps
							 * 3: 11Mbps
							 */
#define RTW_BBP_SYS3			0x13
/* carrier-sense threshold */
#define RTW_BBP_SYS3_CSTHRESH_MASK	BITS(0,3)
#define RTW_BBP_CHESTLIM	0x19
#define RTW_BBP_CHSQLIM		0x1a