xref: /src/sys/dev/ic/rtwreg.h

/*	$NetBSD: rtwreg.h,v 1.24.18.3 2010/08/11 22:53:30 yamt Exp $	*/
/*-
 * Copyright (c) 2004, 2005 David Young.  All rights reserved.
 *
 * Programmed for NetBSD by David Young.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY David Young ``AS IS'' AND ANY
 * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
 * PARTICULAR PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL David
 * Young BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
 * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
 * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
 * OF SUCH DAMAGE.
 */

#include <lib/libkern/libkern.h>

/* RTL8180L Host Control and Status Registers */

#define RTW_IDR0	0x00	/* ID Register: MAC addr, 6 bytes.
				 * Auto-loaded from EEPROM. Read by byte,
				 * by word, or by double word, but write
				 * only by double word.
				 */
#define RTW_IDR1	0x04

#define RTW_MAR0	0x08	/* Multicast filter, 64b. */
#define RTW_MAR1	0x0c

#define RTW_TSFTRL	0x18	/* Timing Synchronization Function Timer
				 * Register, low word, 32b, read-only.
				 */
#define RTW_TSFTRH	0x1c	/* High word, 32b, read-only. */
#define	RTW_TLPDA	0x20	/* Transmit Low Priority Descriptors Start
				 * Address, 32b, 256-byte alignment.
				 */
#define	RTW_TNPDA	0x24	/* Transmit Normal Priority Descriptors Start
				 * Address, 32b, 256-byte alignment.
				 */
#define	RTW_THPDA	0x28	/* Transmit High Priority Descriptors Start
				 * Address, 32b, 256-byte alignment.
				 */

#define RTW_BRSR	0x2c	/* Basic Rate Set Register, 16b */
#define	RTW_BRSR_BPLCP	__BIT(8)/* 1: use short PLCP header for CTS/ACK packet,
				 * 0: use long PLCP header
				 */
#define RTW_BRSR_MBR8180_MASK	__BITS(1,0)	/* Maximum Basic Service Rate */
#define RTW_BRSR_MBR8180_1MBPS	__SHIFTIN(0, RTW_BRSR_MBR8180_MASK)
#define RTW_BRSR_MBR8180_2MBPS	__SHIFTIN(1, RTW_BRSR_MBR8180_MASK)
#define RTW_BRSR_MBR8180_5MBPS	__SHIFTIN(2, RTW_BRSR_MBR8180_MASK)
#define RTW_BRSR_MBR8180_11MBPS	__SHIFTIN(3, RTW_BRSR_MBR8180_MASK)

/* 8181 and 8180 docs conflict! */
#define RTW_BRSR_MBR8181_1MBPS	__BIT(0)
#define RTW_BRSR_MBR8181_2MBPS	__BIT(1)
#define RTW_BRSR_MBR8181_5MBPS	__BIT(2)
#define RTW_BRSR_MBR8181_11MBPS	__BIT(3)

#define RTW_BSSID	0x2e
/* BSSID, 6 bytes */
#define RTW_BSSID16	0x2e		/* first two bytes */
#define RTW_BSSID32	(0x2e + 4)	/* remaining four bytes */
#define RTW_BSSID0	RTW_BSSID16		/* BSSID[0], 8b */
#define RTW_BSSID1	(RTW_BSSID0 + 1)	/* BSSID[1], 8b */
#define RTW_BSSID2	(RTW_BSSID1 + 1)	/* BSSID[2], 8b */
#define RTW_BSSID3	(RTW_BSSID2 + 1)	/* BSSID[3], 8b */
#define RTW_BSSID4	(RTW_BSSID3 + 1)	/* BSSID[4], 8b */
#define RTW_BSSID5	(RTW_BSSID4 + 1)	/* BSSID[5], 8b */

#define	RTW_CR		0x37	/* Command Register, 8b */
#define	RTW_CR_RST	__BIT(4)/* Reset: host sets to 1 to disable
				 * transmitter & receiver, reinitialize FIFO.
				 * RTL8180L sets to 0 to signal completion.
				 */
#define	RTW_CR_RE	__BIT(3)/* Receiver Enable: host enables receiver
				 * by writing 1. RTL8180L indicates receiver
				 * is active with 1. After power-up, host
				 * must wait for reset before writing.
				 */
#define	RTW_CR_TE	__BIT(2)/* Transmitter Enable: host enables transmitter
				 * by writing 1. RTL8180L indicates transmitter
				 * is active with 1. After power-up, host
				 * must wait for reset before writing.
				 */
#define	RTW_CR_MULRW	__BIT(0)/* PCI Multiple Read/Write enable: 1 enables,
				 * 0 disables. XXX RTL8180, only?
				 */

#define	RTW_IMR		0x3c	/* Interrupt Mask Register, 16b */
#define	RTW_ISR		0x3e	/* Interrupt status register, 16b */

#define RTW_INTR_TXFOVW		__BIT(15)	/* Tx FIFO underflow */
#define RTW_INTR_TIMEOUT	__BIT(14)	/* Time Out: 1 indicates
						 * RTW_TSFTR[0:31] = RTW_TINT
						 */
/* Beacon Time Out: time for host to prepare beacon:
 * RTW_TSFTR % (RTW_BCNITV_BCNITV * TU) =
 * (RTW_BCNITV_BCNITV * TU - RTW_BINTRITV)
 */
#define RTW_INTR_BCNINT		__BIT(13)
/* ATIM Time Out: ATIM interval will pass,
 * RTW_TSFTR % (RTW_BCNITV_BCNITV * TU) =
 * (RTW_ATIMWND_ATIMWND * TU - RTW_ATIMTRITV)
 */
#define RTW_INTR_ATIMINT	__BIT(12)
/* Tx Beacon Descriptor Error: beacon transmission aborted because frame Rx'd */
#define RTW_INTR_TBDER	__BIT(11)
#define RTW_INTR_TBDOK	__BIT(10)	/* Tx Beacon Descriptor OK */
#define RTW_INTR_THPDER	__BIT(9)/* Tx High Priority Descriptor Error:
				 * reached short/long retry limit
				 */
#define RTW_INTR_THPDOK	__BIT(8)/* Tx High Priority Descriptor OK */
#define RTW_INTR_TNPDER	__BIT(7)/* Tx Normal Priority Descriptor Error:
				 * reached short/long retry limit
				 */
#define RTW_INTR_TNPDOK	__BIT(6)/* Tx Normal Priority Descriptor OK */
#define RTW_INTR_RXFOVW	__BIT(5)/* Rx FIFO Overflow: either RDU (see below)
				 * or PCI bus too slow/busy
				 */
#define RTW_INTR_RDU	__BIT(4)/* Rx Descriptor Unavailable */
#define RTW_INTR_TLPDER	__BIT(3)/* Tx Normal Priority Descriptor Error
				 * reached short/long retry limit
				 */
#define RTW_INTR_TLPDOK	__BIT(2)/* Tx Normal Priority Descriptor OK */
#define RTW_INTR_RER	__BIT(1)/* Rx Error: CRC32 or ICV error */
#define RTW_INTR_ROK	__BIT(0)/* Rx OK */

/* Convenient interrupt conjunctions. */
#define RTW_INTR_RX	(RTW_INTR_RER|RTW_INTR_ROK|RTW_INTR_RDU|RTW_INTR_RXFOVW)
#define RTW_INTR_TX	(RTW_INTR_TLPDER|RTW_INTR_TLPDOK|RTW_INTR_THPDER|\
			 RTW_INTR_THPDOK|RTW_INTR_TNPDER|RTW_INTR_TNPDOK|\
			 RTW_INTR_TBDER|RTW_INTR_TBDOK)
#define RTW_INTR_BEACON	(RTW_INTR_BCNINT|RTW_INTR_TBDER|RTW_INTR_TBDOK)
#define RTW_INTR_IOERROR	(RTW_INTR_TXFOVW)

#define	RTW_TCR		0x40	/* Transmit Configuration Register, 32b */
#define RTW_TCR_CWMIN	__BIT(31)/* 1: CWmin = 8, 0: CWmin = 32. */
#define RTW_TCR_SWSEQ	__BIT(30)/* 1: host assigns 802.11 sequence number,
				 * 0: hardware assigns sequence number
				 */
/* Hardware version ID, read-only */
#define RTW_TCR_HWVERID_MASK	__BITS(29, 25)
#define RTW_TCR_HWVERID_D	__SHIFTIN(26, RTW_TCR_HWVERID_MASK)
#define RTW_TCR_HWVERID_F	__SHIFTIN(27, RTW_TCR_HWVERID_MASK)
#define RTW_TCR_HWVERID_RTL8180	RTW_TCR_HWVERID_F

/* Set ACK/CTS Timeout (EIFS).
 * 1: ACK rate = max(RTW_BRSR_MBR, Rx rate) (XXX not min? typo in datasheet?)
 * 0: ACK rate = 1Mbps
 */
#define RTW_TCR_SAT	__BIT(24)
/* Max DMA Burst Size per Tx DMA Burst */
#define RTW_TCR_MXDMA_MASK	__BITS(23,21)
#define RTW_TCR_MXDMA_16	__SHIFTIN(0, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_32	__SHIFTIN(1, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_64	__SHIFTIN(2, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_128	__SHIFTIN(3, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_256	__SHIFTIN(4, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_512	__SHIFTIN(5, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_1024	__SHIFTIN(6, RTW_TCR_MXDMA_MASK)
#define RTW_TCR_MXDMA_2048	__SHIFTIN(7, RTW_TCR_MXDMA_MASK)

/* disable 802.11 random backoff */
#define RTW_TCR_DISCW		__BIT(20)

/* host lets RTL8180 append ICV to WEP packets */
#define RTW_TCR_ICV		__BIT(19)

/* Loopback Test: disables TXI/TXQ outputs. */
#define RTW_TCR_LBK_MASK	__BITS(18,17)
#define RTW_TCR_LBK_NORMAL	__SHIFTIN(0, RTW_TCR_LBK_MASK) /* normal ops */
#define RTW_TCR_LBK_MAC		__SHIFTIN(1, RTW_TCR_LBK_MASK) /* MAC loopback */
#define RTW_TCR_LBK_BBP		__SHIFTIN(2, RTW_TCR_LBK_MASK) /* baseband loop. */
#define RTW_TCR_LBK_CONT	__SHIFTIN(3, RTW_TCR_LBK_MASK) /* continuous Tx */

#define RTW_TCR_CRC	__BIT(16)	/* 0: RTL8180 appends CRC32
					 * 1: host appends CRC32
					 *
					 * (I *think* this is right.
					 *  The docs have a mysterious
					 *  description in the
					 *  passive voice.)
					 */
#define RTW_TCR_SRL_MASK	__BITS(15,8)	/* Short Retry Limit */
#define RTW_TCR_LRL_MASK	__BITS(7,0)	/* Long Retry Limit */

#define	RTW_RCR		0x44	/* Receive Configuration Register, 32b */
/* only do Early Rx on packets longer than 1536 bytes */
#define RTW_RCR_ONLYERLPKT	__BIT(31)
/* enable carrier sense method 2 */
#define RTW_RCR_ENCS2		__BIT(30)
/* enable carrier sense method 1 */
#define RTW_RCR_ENCS1		__BIT(29)
#define RTW_RCR_ENMARP		__BIT(28)	/* enable MAC auto-reset PHY */
/* Check BSSID/ToDS/FromDS: set "Link On" when received BSSID
 * matches RTW_BSSID and received ToDS/FromDS are appropriate
 * according to RTW_MSR_NETYPE.
 */
#define RTW_RCR_CBSSID		__BIT(23)
 /* accept packets w/ PWRMGMT bit set */
#define RTW_RCR_APWRMGT		__BIT(22)
/* when RTW_MSR_NETYPE == RTW_MSR_NETYPE_INFRA_OK, accept
 * broadcast/multicast packets whose 3rd address matches RTL8180's MAC.
 */
#define RTW_RCR_ADD3		__BIT(21)
#define RTW_RCR_AMF		__BIT(20)	/* accept management frames */
#define RTW_RCR_ACF		__BIT(19)	/* accept control frames */
#define RTW_RCR_ADF		__BIT(18)	/* accept data frames */
/* Rx FIFO Threshold: RTL8180 begins PCI transfer when this many data
 * bytes are received
 */
#define RTW_RCR_RXFTH_MASK	__BITS(15,13)
#define RTW_RCR_RXFTH_64	__SHIFTIN(2, RTW_RCR_RXFTH_MASK)
#define RTW_RCR_RXFTH_128	__SHIFTIN(3, RTW_RCR_RXFTH_MASK)
#define RTW_RCR_RXFTH_256	__SHIFTIN(4, RTW_RCR_RXFTH_MASK)
#define RTW_RCR_RXFTH_512	__SHIFTIN(5, RTW_RCR_RXFTH_MASK)
#define RTW_RCR_RXFTH_1024	__SHIFTIN(6, RTW_RCR_RXFTH_MASK)
#define RTW_RCR_RXFTH_WHOLE	__SHIFTIN(7, RTW_RCR_RXFTH_MASK)

#define RTW_RCR_AICV		__BIT(12)/* accept frames w/ ICV errors */

/* Max DMA Burst Size per Rx DMA Burst */
#define RTW_RCR_MXDMA_MASK	__BITS(10,8)
#define RTW_RCR_MXDMA_16	__SHIFTIN(0, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_32	__SHIFTIN(1, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_64	__SHIFTIN(2, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_128	__SHIFTIN(3, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_256	__SHIFTIN(4, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_512	__SHIFTIN(5, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_1024	__SHIFTIN(6, RTW_RCR_MXDMA_MASK)
#define RTW_RCR_MXDMA_UNLIMITED	__SHIFTIN(7, RTW_RCR_MXDMA_MASK)

/* EEPROM type, read-only. 1: EEPROM is 93c56, 0: 93c46 */
#define RTW_RCR_9356SEL		__BIT(6)

#define RTW_RCR_ACRC32		__BIT(5)/* accept frames w/ CRC32 errors */
#define RTW_RCR_AB		__BIT(3)/* accept broadcast frames */
#define RTW_RCR_AM		__BIT(2)/* accept multicast frames */
/* accept physical match frames. XXX means PLCP header ok? */
#define RTW_RCR_APM		__BIT(1)
#define RTW_RCR_AAP		__BIT(0)/* accept frames w/ destination */

/* Additional bits to set in monitor mode. */
#define RTW_RCR_MONITOR (		\
    RTW_RCR_AAP |			\
    RTW_RCR_ACF |			\
    RTW_RCR_ACRC32 |			\
    RTW_RCR_AICV |			\
    0)

/* The packet filter bits. */
#define	RTW_RCR_PKTFILTER_MASK (\
    RTW_RCR_AAP |		\
    RTW_RCR_AB |		\
    RTW_RCR_ACF |		\
    RTW_RCR_ACRC32 |		\
    RTW_RCR_ADD3 |		\
    RTW_RCR_ADF |		\
    RTW_RCR_AICV |		\
    RTW_RCR_AM |		\
    RTW_RCR_AMF |		\
    RTW_RCR_APM |		\
    RTW_RCR_APWRMGT |		\
    0)

/* Receive power-management frames and mgmt/ctrl/data frames. */
#define	RTW_RCR_PKTFILTER_DEFAULT	(	\
    RTW_RCR_ACF |				\
    RTW_RCR_ADF |				\
    RTW_RCR_AMF |				\
    RTW_RCR_APM |				\
    RTW_RCR_APWRMGT |				\
    0)

#define RTW_TINT	0x48	/* Timer Interrupt Register, 32b */
#define	RTW_TBDA	0x4c	/* Transmit Beacon Descriptor Start Address,
				 * 32b, 256-byte alignment
				 */
#define RTW_9346CR	0x50	/* 93c46/93c56 Command Register, 8b */
#define RTW_9346CR_EEM_MASK	__BITS(7,6)	/* Operating Mode */
#define RTW_9346CR_EEM_NORMAL	__SHIFTIN(0, RTW_9346CR_EEM_MASK)
/* Load the EEPROM. Reset registers to defaults.
 * Takes ~2ms. RTL8180 indicates completion with RTW_9346CR_EEM_NORMAL.
 * XXX RTL8180 only?
 */
#define RTW_9346CR_EEM_AUTOLOAD	__SHIFTIN(1, RTW_9346CR_EEM_MASK)
/* Disable network & bus-master operations and enable
 * _EECS, _EESK, _EEDI, _EEDO.
 * XXX RTL8180 only?
 */
#define RTW_9346CR_EEM_PROGRAM	__SHIFTIN(2, RTW_9346CR_EEM_MASK)
/* Enable RTW_CONFIG[0123] registers. */
#define RTW_9346CR_EEM_CONFIG	__SHIFTIN(3, RTW_9346CR_EEM_MASK)
/* EEPROM pin status/control in _EEM_CONFIG, _EEM_AUTOLOAD modes.
 * XXX RTL8180 only?
 */
#define RTW_9346CR_EECS	__BIT(3)
#define RTW_9346CR_EESK	__BIT(2)
#define RTW_9346CR_EEDI	__BIT(1)
#define RTW_9346CR_EEDO	__BIT(0)	/* read-only */

#define RTW_CONFIG0	0x51	/* Configuration Register 0, 8b */
#define RTW_CONFIG0_WEP40	__BIT(7)/* implements 40-bit WEP,
					 * XXX RTL8180 only?
					 */
#define RTW_CONFIG0_WEP104	__BIT(6)/* implements 104-bit WEP,
					 * from EEPROM, read-only
					 * XXX RTL8180 only?
					 */
#define RTW_CONFIG0_LEDGPOEN	__BIT(4)/* 1: RTW_PSR_LEDGPO[01] control
					 *    LED[01] pins.
					 * 0: LED behavior defined by
					 *    RTW_CONFIG1_LEDS10_MASK
					 * XXX RTL8180 only?
					 */
/* auxiliary power is present, read-only */
#define RTW_CONFIG0_AUXPWR	__BIT(3)
/* Geographic Location, read-only */
#define RTW_CONFIG0_GL_MASK		__BITS(1,0)
/* _RTW_CONFIG0_GL_* is what the datasheet says, but RTW_CONFIG0_GL_*
 * work.
 */
#define _RTW_CONFIG0_GL_USA		__SHIFTIN(3, RTW_CONFIG0_GL_MASK)
#define RTW_CONFIG0_GL_EUROPE		__SHIFTIN(2, RTW_CONFIG0_GL_MASK)
#define RTW_CONFIG0_GL_JAPAN		__SHIFTIN(1, RTW_CONFIG0_GL_MASK)
#define RTW_CONFIG0_GL_USA		__SHIFTIN(0, RTW_CONFIG0_GL_MASK)
/* RTL8181 datasheet says RTW_CONFIG0_GL_JAPAN = 0. */

#define RTW_CONFIG1	0x52	/* Configuration Register 1, 8b */

/* LED configuration. From EEPROM. Read/write.
 *
 * Setting				LED0		LED1
 * -------				----		----
 * RTW_CONFIG1_LEDS_ACT_INFRA		Activity	Infrastructure
 * RTW_CONFIG1_LEDS_ACT_LINK		Activity	Link
 * RTW_CONFIG1_LEDS_TX_RX		Tx		Rx
 * RTW_CONFIG1_LEDS_LINKACT_INFRA	Link/Activity	Infrastructure
 */
#define RTW_CONFIG1_LEDS_MASK	__BITS(7,6)
#define RTW_CONFIG1_LEDS_ACT_INFRA	__SHIFTIN(0, RTW_CONFIG1_LEDS_MASK)
#define RTW_CONFIG1_LEDS_ACT_LINK	__SHIFTIN(1, RTW_CONFIG1_LEDS_MASK)
#define RTW_CONFIG1_LEDS_TX_RX		__SHIFTIN(2, RTW_CONFIG1_LEDS_MASK)
#define RTW_CONFIG1_LEDS_LINKACT_INFRA	__SHIFTIN(3, RTW_CONFIG1_LEDS_MASK)

/* LWAKE Output Signal. Only applicable to Cardbus. Pulse width is 150ms.
 *
 *                                   RTW_CONFIG1_LWACT
 *				0			1
 * RTW_CONFIG4_LWPTN	0	active high		active low
 *			1	positive pulse		negative pulse
 */
#define RTW_CONFIG1_LWACT	__BIT(4)

#define RTW_CONFIG1_MEMMAP	__BIT(3)/* using PCI memory space, read-only */
#define RTW_CONFIG1_IOMAP	__BIT(2)/* using PCI I/O space, read-only */
#define RTW_CONFIG1_VPD		__BIT(1)/* if set, VPD from offsets
					 * 0x40-0x7f in EEPROM are at
					 * registers 0x60-0x67 of PCI
					 * Configuration Space (XXX huh?)
					 */
#define RTW_CONFIG1_PMEN	__BIT(0)/* Power Management Enable: TBD */

#define RTW_CONFIG2	0x53	/* Configuration Register 2, 8b */
#define RTW_CONFIG2_LCK	__BIT(7)/* clocks are locked, read-only:
				 * Tx frequency & symbol clocks
				 * are derived from the same OSC
				 */
#define RTW_CONFIG2_ANT	__BIT(6)	/* diversity enabled, read-only */
#define RTW_CONFIG2_DPS	__BIT(3)	/* Descriptor Polling State: enable
					 * test mode.
					 */
#define RTW_CONFIG2_PAPESIGN	__BIT(2)		/* TBD, from EEPROM */
#define RTW_CONFIG2_PAPETIME_MASK	__BITS(1,0)	/* TBD, from EEPROM */

#define	RTW_ANAPARM	0x54	/* Analog parameter, 32b */
#define RTW_ANAPARM_RFPOW0_MASK	__BITS(30,28)		/* undocumented bits
							 * which appear to
							 * control the power
							 * state of the RF
							 * components
							 */
#define	RTW_ANAPARM_RFPOW_MASK	\
    (RTW_ANAPARM_RFPOW0_MASK|RTW_ANAPARM_RFPOW1_MASK)

#define RTW_ANAPARM_TXDACOFF	__BIT(27)		/* 1: disable Tx DAC,
							 * 0: enable
							 */
#define RTW_ANAPARM_RFPOW1_MASK	__BITS(26,20)		/* undocumented bits
							 * which appear to
							 * control the power
							 * state of the RF
							 * components
							 */

/*
 * Maxim On/Sleep/Off control
 */
#define RTW_ANAPARM_RFPOW_MAXIM_ON	__SHIFTIN(0x8, RTW_ANAPARM_RFPOW1_MASK)

/* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */
#define RTW_ANAPARM_RFPOW_MAXIM_SLEEP	__SHIFTIN(0x378, RTW_ANAPARM_RFPOW1_MASK)

/* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */
#define RTW_ANAPARM_RFPOW_MAXIM_OFF	__SHIFTIN(0x379, RTW_ANAPARM_RFPOW1_MASK)

/*
 * RFMD On/Sleep/Off control
 */
#define RTW_ANAPARM_RFPOW_RFMD_ON	__SHIFTIN(0x408, RTW_ANAPARM_RFPOW1_MASK)

/* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */
#define RTW_ANAPARM_RFPOW_RFMD_SLEEP	__SHIFTIN(0x378, RTW_ANAPARM_RFPOW1_MASK)

/* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */
#define RTW_ANAPARM_RFPOW_RFMD_OFF	__SHIFTIN(0x379, RTW_ANAPARM_RFPOW1_MASK)

/*
 * Philips On/Sleep/Off control
 */
#define RTW_ANAPARM_RFPOW_ANA_PHILIPS_ON	\
    __SHIFTIN(0x328, RTW_ANAPARM_RFPOW1_MASK)
#define RTW_ANAPARM_RFPOW_DIG_PHILIPS_ON	\
    __SHIFTIN(0x008, RTW_ANAPARM_RFPOW1_MASK)

/* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */
#define RTW_ANAPARM_RFPOW_PHILIPS_SLEEP\
    __SHIFTIN(0x378, RTW_ANAPARM_RFPOW1_MASK)

/* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */
#define RTW_ANAPARM_RFPOW_PHILIPS_OFF\
    __SHIFTIN(0x379, RTW_ANAPARM_RFPOW1_MASK)

#define RTW_ANAPARM_RFPOW_PHILIPS_ON	__SHIFTIN(0x328, RTW_ANAPARM_RFPOW1_MASK)

#define RTW_ANAPARM_CARDSP_MASK	__BITS(19,0)		/* undocumented
							 * card-specific
							 * bits from the
							 * EEPROM.
							 */

#define RTW_MSR		0x58	/* Media Status Register, 8b */
/* Network Type and Link Status */
#define RTW_MSR_NETYPE_MASK	__BITS(3,2)
/* AP, XXX RTL8181 only? */
#define RTW_MSR_NETYPE_AP_OK	__SHIFTIN(3, RTW_MSR_NETYPE_MASK)
/* infrastructure link ok */
#define RTW_MSR_NETYPE_INFRA_OK	__SHIFTIN(2, RTW_MSR_NETYPE_MASK)
/* ad-hoc link ok */
#define RTW_MSR_NETYPE_ADHOC_OK	__SHIFTIN(1, RTW_MSR_NETYPE_MASK)
/* no link */
#define RTW_MSR_NETYPE_NOLINK	__SHIFTIN(0, RTW_MSR_NETYPE_MASK)

#define RTW_CONFIG3	0x59	/* Configuration Register 3, 8b */
#define RTW_CONFIG3_GNTSEL	__BIT(7)	/* Grant Select, read-only */
#define RTW_CONFIG3_PARMEN	__BIT(6)	/* Set RTW_CONFIG3_PARMEN and
						 * RTW_9346CR_EEM_CONFIG to
						 * allow RTW_ANAPARM writes.
						 */
#define RTW_CONFIG3_MAGIC	__BIT(5)/* Valid when RTW_CONFIG1_PMEN is
					 * set. If set, RTL8180 wakes up
					 * OS when Magic Packet is Rx'd.
					 */
#define RTW_CONFIG3_CARDBEN	__BIT(3)/* Cardbus-related registers
					 * and functions are enabled,
					 * read-only. XXX RTL8180 only.
					 */
#define RTW_CONFIG3_CLKRUNEN	__BIT(2)/* CLKRUN enabled, read-only.
					 * XXX RTL8180 only.
					 */
#define RTW_CONFIG3_FUNCREGEN	__BIT(1)/* Function Registers Enabled,
					 * read-only. XXX RTL8180 only.
					 */
#define RTW_CONFIG3_FBTBEN	__BIT(0)/* Fast back-to-back enabled,
					 * read-only.
					 */
#define RTW_CONFIG4	0x5A	/* Configuration Register 4, 8b */
#define RTW_CONFIG4_VCOPDN	__BIT(7)/* VCO Power Down
					 * 0: normal operation
					 *    (power-on default)
					 * 1: power-down VCO, RF front-end,
					 *    and most RTL8180 components.
					 */
#define RTW_CONFIG4_PWROFF	__BIT(6)/* Power Off
					 * 0: normal operation
					 *    (power-on default)
					 * 1: power-down RF front-end,
					 *    and most RTL8180 components,
					 *    but leave VCO on.
					 *
					 * XXX RFMD front-end only?
					 */
#define RTW_CONFIG4_PWRMGT	__BIT(5)/* Power Management
					 * 0: normal operation
					 *    (power-on default)
					 * 1: set Tx packet's PWRMGMT bit.
					 */
#define RTW_CONFIG4_LWPME	__BIT(4)/* LANWAKE vs. PMEB: Cardbus-only
					 * 0: LWAKE & PMEB asserted
					 *    simultaneously
					 * 1: LWAKE asserted only if
					 *    both PMEB is asserted and
					 *    ISOLATEB is low.
					 * XXX RTL8180 only.
					 */
#define RTW_CONFIG4_LWPTN	__BIT(2)/* see RTW_CONFIG1_LWACT
					 * XXX RTL8180 only.
					 */
/* Radio Front-End Programming Method */
#define RTW_CONFIG4_RFTYPE_MASK	__BITS(1,0)
#define RTW_CONFIG4_RFTYPE_INTERSIL	__SHIFTIN(1, RTW_CONFIG4_RFTYPE_MASK)
#define RTW_CONFIG4_RFTYPE_RFMD		__SHIFTIN(2, RTW_CONFIG4_RFTYPE_MASK)
#define RTW_CONFIG4_RFTYPE_PHILIPS	__SHIFTIN(3, RTW_CONFIG4_RFTYPE_MASK)

#define RTW_TESTR	0x5B	/* TEST mode register, 8b */

#define RTW_PSR		0x5e	/* Page Select Register, 8b */
#define RTW_PSR_GPO	__BIT(7)/* Control/status of pin 52. */
#define RTW_PSR_GPI	__BIT(6)/* Status of pin 64. */
#define RTW_PSR_LEDGPO1	__BIT(5)/* Status/control of LED1 pin if
				 * RTW_CONFIG0_LEDGPOEN is set.
				 */
#define RTW_PSR_LEDGPO0	__BIT(4)/* Status/control of LED0 pin if
				 * RTW_CONFIG0_LEDGPOEN is set.
				 */
#define RTW_PSR_UWF	__BIT(1)/* Enable Unicast Wakeup Frame */
#define RTW_PSR_PSEN	__BIT(0)/* 1: page 1, 0: page 0 */

#define RTW_SCR		0x5f	/* Security Configuration Register, 8b */
#define RTW_SCR_KM_MASK	__BITS(5,4)	/* Key Mode */
#define RTW_SCR_KM_WEP104	__SHIFTIN(1, RTW_SCR_KM_MASK)
#define RTW_SCR_KM_WEP40	__SHIFTIN(0, RTW_SCR_KM_MASK)
#define RTW_SCR_TXSECON		__BIT(1)/* Enable Tx WEP. Invalid if
					 * neither RTW_CONFIG0_WEP40 nor
					 * RTW_CONFIG0_WEP104 is set.
					 */
#define RTW_SCR_RXSECON		__BIT(0)/* Enable Rx WEP. Invalid if
					 * neither RTW_CONFIG0_WEP40 nor
					 * RTW_CONFIG0_WEP104 is set.
					 */

#define	RTW_BCNITV	0x70	/* Beacon Interval Register, 16b */
#define	RTW_BCNITV_BCNITV_MASK	__BITS(9,0)	/* TU between TBTT, written
						 * by host.
						 */
#define	RTW_ATIMWND	0x72	/* ATIM Window Register, 16b */
#define	RTW_ATIMWND_ATIMWND	__BITS(9,0)	/* ATIM Window length in TU,
						 * written by host.
						 */

#define RTW_BINTRITV	0x74	/* Beacon Interrupt Interval Register, 16b */
#define	RTW_BINTRITV_BINTRITV	__BITS(9,0)	/* RTL8180 wakes host with
						 * RTW_INTR_BCNINT at BINTRITV
						 * microseconds before TBTT
						 */
#define RTW_ATIMTRITV	0x76	/* ATIM Interrupt Interval Register, 16b */
#define	RTW_ATIMTRITV_ATIMTRITV	__BITS(9,0)	/* RTL8180 wakes host with
						 * RTW_INTR_ATIMINT at ATIMTRITV
						 * microseconds before end of
						 * ATIM Window
						 */

#define RTW_PHYDELAY	0x78	/* PHY Delay Register, 8b */
#define RTW_PHYDELAY_REVC_MAGIC	__BIT(3)	/* Rev. C magic from reference
						 * driver
						 */
#define RTW_PHYDELAY_PHYDELAY	__BITS(2,0)	/* microsecond Tx delay between
						 * MAC and RF front-end
						 */
#define RTW_CRCOUNT	0x79	/* Carrier Sense Counter, 8b */
#define	RTW_CRCOUNT_MAGIC	0x4c

#define RTW_CRC16ERR	0x7a	/* CRC16 error count, 16b, XXX RTL8181 only? */

#define RTW_BB	0x7c		/* Baseband interface, 32b */
/* used for writing RTL8180's integrated baseband processor */
#define RTW_BB_RD_MASK		__BITS(23,16)	/* data to read */
#define RTW_BB_WR_MASK		__BITS(15,8)	/* data to write */
#define RTW_BB_WREN		__BIT(7)	/* write enable */
#define RTW_BB_ADDR_MASK	__BITS(6,0)	/* address */

#define RTW_PHYADDR	0x7c	/* Address register for PHY interface, 8b */
#define RTW_PHYDATAW	0x7d	/* Write data to PHY, 8b, write-only */
#define RTW_PHYDATAR	0x7e	/* Read data from PHY, 8b (?), read-only */

#define RTW_PHYCFG	0x80	/* PHY Configuration Register, 32b */
#define RTW_PHYCFG_MAC_POLL	__BIT(31)	/* if !RTW_PHYCFG_HST,
						 * host sets. MAC clears
						 * after banging bits.
						 */
#define	RTW_PHYCFG_HST		__BIT(30)	/* 1: host bangs bits
						 * 0: MAC bangs bits
						 */
#define RTW_PHYCFG_MAC_RFTYPE_MASK	__BITS(29,28)
#define RTW_PHYCFG_MAC_RFTYPE_INTERSIL	__SHIFTIN(0, RTW_PHYCFG_MAC_RFTYPE_MASK)
#define RTW_PHYCFG_MAC_RFTYPE_RFMD	__SHIFTIN(1, RTW_PHYCFG_MAC_RFTYPE_MASK)
#define RTW_PHYCFG_MAC_RFTYPE_GCT	RTW_PHYCFG_MAC_RFTYPE_RFMD
#define RTW_PHYCFG_MAC_RFTYPE_PHILIPS	__SHIFTIN(3, RTW_PHYCFG_MAC_RFTYPE_MASK)
#define RTW_PHYCFG_MAC_PHILIPS_ADDR_MASK	__BITS(27,24)
#define RTW_PHYCFG_MAC_PHILIPS_DATA_MASK	__BITS(23,0)
#define RTW_PHYCFG_MAC_MAXIM_LODATA_MASK	__BITS(27,24)
#define RTW_PHYCFG_MAC_MAXIM_ADDR_MASK		__BITS(11,8)
#define RTW_PHYCFG_MAC_MAXIM_HIDATA_MASK	__BITS(7,0)
#define	RTW_PHYCFG_HST_EN		__BIT(2)
#define	RTW_PHYCFG_HST_CLK		__BIT(1)
#define	RTW_PHYCFG_HST_DATA		__BIT(0)

#define	RTW_MAXIM_HIDATA_MASK			__BITS(11,4)
#define	RTW_MAXIM_LODATA_MASK			__BITS(3,0)

/**
 ** 0x84 - 0xD3, page 1, selected when RTW_PSR[PSEN] == 1.
 **/

#define	RTW_WAKEUP0L	0x84	/* Power Management Wakeup Frame */
#define	RTW_WAKEUP0H	0x88	/* 32b */

#define	RTW_WAKEUP1L	0x8c
#define	RTW_WAKEUP1H	0x90

#define	RTW_WAKEUP2LL	0x94
#define	RTW_WAKEUP2LH	0x98

#define	RTW_WAKEUP2HL	0x9c
#define	RTW_WAKEUP2HH	0xa0

#define	RTW_WAKEUP3LL	0xa4
#define	RTW_WAKEUP3LH	0xa8

#define	RTW_WAKEUP3HL	0xac
#define	RTW_WAKEUP3HH	0xb0

#define	RTW_WAKEUP4LL	0xb4
#define	RTW_WAKEUP4LH	0xb8

#define	RTW_WAKEUP4HL	0xbc
#define	RTW_WAKEUP4HH	0xc0

#define RTW_CRC0	0xc4	/* CRC of wakeup frame 0, 16b */
#define RTW_CRC1	0xc6	/* CRC of wakeup frame 1, 16b */
#define RTW_CRC2	0xc8	/* CRC of wakeup frame 2, 16b */
#define RTW_CRC3	0xca	/* CRC of wakeup frame 3, 16b */
#define RTW_CRC4	0xcc	/* CRC of wakeup frame 4, 16b */

/**
 ** 0x84 - 0xD3, page 0, selected when RTW_PSR[PSEN] == 0.
 **/

/* Default Key Registers, each 128b
 *
 * If RTW_SCR_KM_WEP104, 104 lsb are the key.
 * If RTW_SCR_KM_WEP40, 40 lsb are the key.
 */
#define RTW_DK0		0x90	/* Default Key 0 Register, 128b */
#define RTW_DK1		0xa0	/* Default Key 1 Register, 128b */
#define RTW_DK2		0xb0	/* Default Key 2 Register, 128b */
#define RTW_DK3		0xc0	/* Default Key 3 Register, 128b */

#define	RTW_CONFIG5	0xd8	/* Configuration Register 5, 8b */
#define RTW_CONFIG5_TXFIFOOK	__BIT(7)/* Tx FIFO self-test pass, read-only */
#define RTW_CONFIG5_RXFIFOOK	__BIT(6)/* Rx FIFO self-test pass, read-only */
#define RTW_CONFIG5_CALON	__BIT(5)/* 1: start calibration cycle
					 *    and raise AGCRESET pin.
					 * 0: lower AGCRESET pin
					 */
#define RTW_CONFIG5_EACPI	__BIT(2)/* Enable ACPI Wake up, default 0 */
#define RTW_CONFIG5_LANWAKE	__BIT(1)/* Enable LAN Wake signal,
					 * from EEPROM
					 */
#define RTW_CONFIG5_PMESTS	__BIT(0)/* 1: both software & PCI Reset
					 *    reset PME_Status
					 * 0: only software resets PME_Status
					 *
					 * From EEPROM.
					 */

#define	RTW_TPPOLL	0xd9	/* Transmit Priority Polling Register, 8b,
				 * write-only.
				 */
#define RTW_TPPOLL_BQ	__BIT(7)/* RTL8180 clears to notify host of a beacon
				 * Tx. Host writes have no effect.
				 */
#define RTW_TPPOLL_HPQ	__BIT(6)/* Host writes 1 to notify RTL8180 of
				 * high-priority Tx packets, RTL8180 clears
				 * to after high-priority Tx is complete.
				 */
#define RTW_TPPOLL_NPQ	__BIT(5)/* If RTW_CONFIG2_DPS is set,
				 * host writes 1 to notify RTL8180 of
				 * normal-priority Tx packets, RTL8180 clears
				 * after normal-priority Tx is complete.
				 *
				 * If RTW_CONFIG2_DPS is clear, host writes
				 * have no effect. RTL8180 clears after
				 * normal-priority Tx is complete.
				 */
#define RTW_TPPOLL_LPQ	__BIT(4)/* Host writes 1 to notify RTL8180 of
				 * low-priority Tx packets, RTL8180 clears
				 * after low-priority Tx is complete.
				 */
#define RTW_TPPOLL_SBQ	__BIT(3)/* Host writes 1 to tell RTL8180 to
				 * stop beacon DMA. This bit is invalid
				 * when RTW_CONFIG2_DPS is set.
				 */
#define RTW_TPPOLL_SHPQ	__BIT(2)/* Host writes 1 to tell RTL8180 to
				 * stop high-priority DMA.
				 */
#define RTW_TPPOLL_SNPQ	__BIT(1)/* Host writes 1 to tell RTL8180 to
				 * stop normal-priority DMA. This bit is invalid
				 * when RTW_CONFIG2_DPS is set.
				 */
#define RTW_TPPOLL_SLPQ	__BIT(0)/* Host writes 1 to tell RTL8180 to
				 * stop low-priority DMA.
				 */

/* Start all queues. */
#define	RTW_TPPOLL_ALL	(RTW_TPPOLL_BQ | RTW_TPPOLL_HPQ | \
			 RTW_TPPOLL_NPQ | RTW_TPPOLL_LPQ)
/* Check all queues' activity. */
#define	RTW_TPPOLL_ACTIVE	RTW_TPPOLL_ALL
/* Stop all queues. */
#define	RTW_TPPOLL_SALL	(RTW_TPPOLL_SBQ | RTW_TPPOLL_SHPQ | \
			 RTW_TPPOLL_SNPQ | RTW_TPPOLL_SLPQ)

#define	RTW_CWR		0xdc	/* Contention Window Register, 16b, read-only */
/* Contention Window: indicates number of contention windows before Tx
 */
#define	RTW_CWR_CW	__BITS(9,0)

/* Retry Count Register, 16b, read-only */
#define	RTW_RETRYCTR	0xde
/* Retry Count: indicates number of retries after Tx */
#define	RTW_RETRYCTR_RETRYCT	__BITS(7,0)

#define RTW_RDSAR	0xe4	/* Receive descriptor Start Address Register,
				 * 32b, 256-byte alignment.
				 */
/* Function Event Register, 32b, Cardbus only. Only valid when
 * both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN are set.
 */
#define RTW_FER		0xf0
#define RTW_FER_INTR	__BIT(15)	/* set when RTW_FFER_INTR is set */
#define RTW_FER_GWAKE	__BIT(4)	/* General Wakeup */
/* Function Event Mask Register, 32b, Cardbus only. Only valid when
 * both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN are set.
 */
#define RTW_FEMR	0xf4
#define RTW_FEMR_INTR	__BIT(15)	/* set when RTW_FFER_INTR is set */
#define RTW_FEMR_WKUP	__BIT(14)	/* Wakeup Mask */
#define RTW_FEMR_GWAKE	__BIT(4)	/* General Wakeup */
/* Function Present State Register, 32b, read-only, Cardbus only.
 * Only valid when both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN
 * are set.
 */
#define RTW_FPSR	0xf8
#define RTW_FPSR_INTR	__BIT(15)	/* TBD */
#define RTW_FPSR_GWAKE	__BIT(4)	/* General Wakeup: TBD */
/* Function Force Event Register, 32b, write-only, Cardbus only.
 * Only valid when both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN
 * are set.
 */
#define RTW_FFER	0xfc
#define RTW_FFER_INTR	__BIT(15)	/* TBD */
#define RTW_FFER_GWAKE	__BIT(4)	/* General Wakeup: TBD */

/* Serial EEPROM offsets */
#define RTW_SR_ID	0x00	/* 16b */
#define RTW_SR_VID	0x02	/* 16b */
#define RTW_SR_DID	0x04	/* 16b */
#define RTW_SR_SVID	0x06	/* 16b */
#define RTW_SR_SMID	0x08	/* 16b */
#define RTW_SR_MNGNT	0x0a
#define RTW_SR_MXLAT	0x0b
#define RTW_SR_RFCHIPID	0x0c
#define RTW_SR_CONFIG3	0x0d
#define RTW_SR_MAC	0x0e	/* 6 bytes */
#define RTW_SR_CONFIG0	0x14
#define RTW_SR_CONFIG1	0x15
#define RTW_SR_PMC	0x16	/* Power Management Capabilities, 16b */
#define RTW_SR_CONFIG2	0x18
#define RTW_SR_CONFIG4	0x19
#define RTW_SR_ANAPARM	0x1a	/* Analog Parameters, 32b */
#define RTW_SR_TESTR	0x1e
#define RTW_SR_CONFIG5	0x1f
#define RTW_SR_TXPOWER1		0x20
#define RTW_SR_TXPOWER2		0x21
#define RTW_SR_TXPOWER3		0x22
#define RTW_SR_TXPOWER4		0x23
#define RTW_SR_TXPOWER5		0x24
#define RTW_SR_TXPOWER6		0x25
#define RTW_SR_TXPOWER7		0x26
#define RTW_SR_TXPOWER8		0x27
#define RTW_SR_TXPOWER9		0x28
#define RTW_SR_TXPOWER10	0x29
#define RTW_SR_TXPOWER11	0x2a
#define RTW_SR_TXPOWER12	0x2b
#define RTW_SR_TXPOWER13	0x2c
#define RTW_SR_TXPOWER14	0x2d
#define RTW_SR_CHANNELPLAN	0x2e	/* bitmap of channels to scan */
#define RTW_SR_ENERGYDETTHR	0x2f	/* energy-detect threshold */
#define RTW_SR_ENERGYDETTHR_DEFAULT	0x0c	/* use this if old SROM */
#define RTW_SR_CISPOINTER	0x30	/* 16b */
#define RTW_SR_RFPARM		0x32	/* RF-specific parameter */
#define RTW_SR_RFPARM_DIGPHY	__BIT(0)	/* 1: digital PHY */
#define RTW_SR_RFPARM_DFLANTB	__BIT(1)	/* 1: antenna B is default */
#define RTW_SR_RFPARM_CS_MASK	__BITS(2,3)	/* carrier-sense type */
#define RTW_SR_VERSION		0x3c	/* EEPROM content version, 16b */
#define RTW_SR_CRC		0x3e	/* EEPROM content CRC, 16b */
#define RTW_SR_VPD		0x40	/* Vital Product Data, 64 bytes */
#define RTW_SR_CIS		0x80	/* CIS Data, 93c56 only, 128 bytes*/

/*
 * RTL8180 Transmit/Receive Descriptors
 */

/* the first descriptor in each ring must be on a 256-byte boundary */
#define RTW_DESC_ALIGNMENT 256

/* Tx descriptor */
struct rtw_txdesc {
	volatile uint32_t	td_ctl0;
	volatile uint32_t	td_ctl1;
	volatile uint32_t	td_buf;
	volatile uint32_t	td_len;
	volatile uint32_t	td_next;
	volatile uint32_t	td_rsvd[3];
} __packed __aligned(4);

#define td_stat td_ctl0

#define RTW_TXCTL0_OWN			__BIT(31)	/* 1: ready to Tx */
#define RTW_TXCTL0_RSVD0		__BIT(30)	/* reserved */
#define RTW_TXCTL0_FS			__BIT(29)	/* first segment */
#define RTW_TXCTL0_LS			__BIT(28)	/* last segment */

#define RTW_TXCTL0_RATE_MASK		__BITS(27,24)	/* Tx rate */
#define RTW_TXCTL0_RATE_1MBPS		__SHIFTIN(0, RTW_TXCTL0_RATE_MASK)
#define RTW_TXCTL0_RATE_2MBPS		__SHIFTIN(1, RTW_TXCTL0_RATE_MASK)
#define RTW_TXCTL0_RATE_5MBPS		__SHIFTIN(2, RTW_TXCTL0_RATE_MASK)
#define RTW_TXCTL0_RATE_11MBPS		__SHIFTIN(3, RTW_TXCTL0_RATE_MASK)

#define RTW_TXCTL0_RTSEN		__BIT(23)	/* RTS Enable */

#define RTW_TXCTL0_RTSRATE_MASK		__BITS(22,19)	/* Tx rate */
#define RTW_TXCTL0_RTSRATE_1MBPS	__SHIFTIN(0, RTW_TXCTL0_RTSRATE_MASK)
#define RTW_TXCTL0_RTSRATE_2MBPS	__SHIFTIN(1, RTW_TXCTL0_RTSRATE_MASK)
#define RTW_TXCTL0_RTSRATE_5MBPS	__SHIFTIN(2, RTW_TXCTL0_RTSRATE_MASK)
#define RTW_TXCTL0_RTSRATE_11MBPS	__SHIFTIN(3, RTW_TXCTL0_RTSRATE_MASK)

#define RTW_TXCTL0_BEACON		__BIT(18)	/* packet is a beacon */
#define RTW_TXCTL0_MOREFRAG		__BIT(17)	/* another fragment
							 * follows
							 */
/* add short PLCP preamble and header */
#define RTW_TXCTL0_SPLCP		__BIT(16)
#define RTW_TXCTL0_KEYID_MASK		__BITS(15,14)	/* default key id */
#define RTW_TXCTL0_RSVD1_MASK		__BITS(13,12)	/* reserved */
#define RTW_TXCTL0_TPKTSIZE_MASK	__BITS(11,0)	/* Tx packet size
							 * in bytes
							 */

#define RTW_TXSTAT_OWN		RTW_TXCTL0_OWN
#define RTW_TXSTAT_RSVD0	RTW_TXCTL0_RSVD0
#define RTW_TXSTAT_FS		RTW_TXCTL0_FS
#define RTW_TXSTAT_LS		RTW_TXCTL0_LS
#define RTW_TXSTAT_RSVD1_MASK	__BITS(27,16)
#define RTW_TXSTAT_TOK		__BIT(15)
#define RTW_TXSTAT_RTSRETRY_MASK	__BITS(14,8)	/* RTS retry count */
#define RTW_TXSTAT_DRC_MASK		__BITS(7,0)	/* Data retry count */

#define RTW_TXCTL1_LENGEXT	__BIT(31)	/* supplements _LENGTH
						 * in packets sent 5.5Mb/s or
						 * faster
						 */
#define RTW_TXCTL1_LENGTH_MASK	__BITS(30,16)	/* PLCP length (microseconds) */
#define RTW_TXCTL1_RTSDUR_MASK	__BITS(15,0)	/* RTS Duration
						 * (microseconds)
						 */

#define RTW_TXLEN_LENGTH_MASK	__BITS(11,0)	/* Tx buffer length in bytes */

/* Rx descriptor */
struct rtw_rxdesc {
	volatile uint32_t	rd_ctl;
	volatile uint32_t	rd_rsvd0;
	volatile uint32_t	rd_buf;
	volatile uint32_t	rd_rsvd1;
} __packed __aligned(4);

#define rd_stat rd_ctl
#define rd_rssi rd_rsvd0
#define rd_tsftl rd_buf		/* valid only when RTW_RXSTAT_LS is set */
#define rd_tsfth rd_rsvd1	/* valid only when RTW_RXSTAT_LS is set */

#define RTW_RXCTL_OWN		__BIT(31)	/* 1: owned by NIC */
#define RTW_RXCTL_EOR		__BIT(30)	/* end of ring */
#define RTW_RXCTL_FS		__BIT(29)	/* first segment */
#define RTW_RXCTL_LS		__BIT(28)	/* last segment */
#define RTW_RXCTL_RSVD0_MASK	__BITS(29,12)	/* reserved */
#define RTW_RXCTL_LENGTH_MASK	__BITS(11,0)	/* Rx buffer length */

#define RTW_RXSTAT_OWN		RTW_RXCTL_OWN
#define RTW_RXSTAT_EOR		RTW_RXCTL_EOR
#define RTW_RXSTAT_FS		RTW_RXCTL_FS	/* first segment */
#define RTW_RXSTAT_LS		RTW_RXCTL_LS	/* last segment */
#define RTW_RXSTAT_DMAFAIL	__BIT(27)	/* DMA failure on this pkt */
#define RTW_RXSTAT_BOVF		__BIT(26)	/* buffer overflow XXX means
						 * FIFO exhausted?
						 */
#define RTW_RXSTAT_SPLCP	__BIT(25)	/* Rx'd with short preamble
						 * and PLCP header
						 */
#define RTW_RXSTAT_RSVD1	__BIT(24)	/* reserved */
#define RTW_RXSTAT_RATE_MASK	__BITS(23,20)	/* Rx rate */
#define RTW_RXSTAT_RATE_1MBPS	__SHIFTIN(0, RTW_RXSTAT_RATE_MASK)
#define RTW_RXSTAT_RATE_2MBPS	__SHIFTIN(1, RTW_RXSTAT_RATE_MASK)
#define RTW_RXSTAT_RATE_5MBPS	__SHIFTIN(2, RTW_RXSTAT_RATE_MASK)
#define RTW_RXSTAT_RATE_11MBPS	__SHIFTIN(3, RTW_RXSTAT_RATE_MASK)
#define RTW_RXSTAT_MIC		__BIT(19)	/* XXX from reference driver */
#define RTW_RXSTAT_MAR		__BIT(18)	/* is multicast */
#define RTW_RXSTAT_PAR		__BIT(17)	/* matches RTL8180's MAC */
#define RTW_RXSTAT_BAR		__BIT(16)	/* is broadcast */
#define RTW_RXSTAT_RES		__BIT(15)	/* error summary. valid when
						 * RTW_RXSTAT_LS set. indicates
						 * that either RTW_RXSTAT_CRC32
						 * or RTW_RXSTAT_ICV is set.
						 */
#define RTW_RXSTAT_PWRMGT	__BIT(14)	/* 802.11 PWRMGMT bit is set */
#define RTW_RXSTAT_CRC16	__BIT(14)	/* XXX CRC16 error, from
						 * reference driver
						 */
#define RTW_RXSTAT_CRC32	__BIT(13)	/* CRC32 error */
#define RTW_RXSTAT_ICV		__BIT(12)	/* ICV error */
#define RTW_RXSTAT_LENGTH_MASK	__BITS(11,0)	/* frame length, including
						 * CRC32
						 */

/* Convenient status conjunction. */
#define RTW_RXSTAT_ONESEG	(RTW_RXSTAT_FS|RTW_RXSTAT_LS)
/* Convenient status disjunctions. */
#define RTW_RXSTAT_IOERROR	(RTW_RXSTAT_DMAFAIL|RTW_RXSTAT_BOVF)
#define RTW_RXSTAT_DEBUG	(RTW_RXSTAT_SPLCP|RTW_RXSTAT_MAR|\
				 RTW_RXSTAT_PAR|RTW_RXSTAT_BAR|\
				 RTW_RXSTAT_PWRMGT|RTW_RXSTAT_CRC32|\
				 RTW_RXSTAT_ICV)


#define RTW_RXRSSI_VLAN		__BITS(31,16)	/* XXX from reference driver */
/* for Philips RF front-ends */
#define RTW_RXRSSI_RSSI		__BITS(15,8)	/* RF energy at the PHY */
/* for RF front-ends by Intersil, Maxim, RFMD */
#define RTW_RXRSSI_IMR_RSSI	__BITS(15,9)	/* RF energy at the PHY */
#define RTW_RXRSSI_IMR_LNA	__BIT(8)	/* 1: LNA activated */
#define RTW_RXRSSI_SQ		__BITS(7,0)	/* Barker code-lock quality */

#define RTW_READ8(regs, ofs)						\
	bus_space_read_1((regs)->r_bt, (regs)->r_bh, (ofs))

#define RTW_READ16(regs, ofs)						\
	bus_space_read_2((regs)->r_bt, (regs)->r_bh, (ofs))

#define RTW_READ(regs, ofs)						\
	bus_space_read_4((regs)->r_bt, (regs)->r_bh, (ofs))

#define RTW_WRITE8(regs, ofs, val)					\
	bus_space_write_1((regs)->r_bt, (regs)->r_bh, (ofs), (val))

#define RTW_WRITE16(regs, ofs, val)					\
	bus_space_write_2((regs)->r_bt, (regs)->r_bh, (ofs), (val))

#define RTW_WRITE(regs, ofs, val)					\
	bus_space_write_4((regs)->r_bt, (regs)->r_bh, (ofs), (val))

#define	RTW_ISSET(regs, reg, mask)					\
	(RTW_READ((regs), (reg)) & (mask))

#define	RTW_CLR(regs, reg, mask)					\
	RTW_WRITE((regs), (reg), RTW_READ((regs), (reg)) & ~(mask))

/* bus_space(9) lied? */
#ifndef BUS_SPACE_BARRIER_SYNC
#define BUS_SPACE_BARRIER_SYNC (BUS_SPACE_BARRIER_READ|BUS_SPACE_BARRIER_WRITE)
#endif

#ifndef BUS_SPACE_BARRIER_READ_BEFORE_READ
#define BUS_SPACE_BARRIER_READ_BEFORE_READ BUS_SPACE_BARRIER_READ
#endif

#ifndef BUS_SPACE_BARRIER_READ_BEFORE_WRITE
#define BUS_SPACE_BARRIER_READ_BEFORE_WRITE BUS_SPACE_BARRIER_READ
#endif

#ifndef BUS_SPACE_BARRIER_WRITE_BEFORE_READ
#define BUS_SPACE_BARRIER_WRITE_BEFORE_READ BUS_SPACE_BARRIER_WRITE
#endif

#ifndef BUS_SPACE_BARRIER_WRITE_BEFORE_WRITE
#define BUS_SPACE_BARRIER_WRITE_BEFORE_WRITE BUS_SPACE_BARRIER_WRITE
#endif

/*
 * Registers for RTL8180L's built-in baseband modem.
 */
#define RTW_BBP_SYS1		0x00
#define RTW_BBP_TXAGC		0x03	/* guess: transmit auto gain control */
#define RTW_BBP_LNADET		0x04	/* guess: low-noise amplifier activation
					 * threshold
					 */
#define RTW_BBP_IFAGCINI	0x05	/* guess: intermediate frequency (IF)
					 * auto-gain control (AGC) initial value
					 */
#define RTW_BBP_IFAGCLIMIT	0x06	/* guess: IF AGC maximum value */
#define RTW_BBP_IFAGCDET	0x07	/* guess: activation threshold for
					 * IF AGC loop
					 */

#define RTW_BBP_ANTATTEN	0x10	/* guess: antenna & attenuation */
#define RTW_BBP_ANTATTEN_GCT_MAGIC		0xa3
#define RTW_BBP_ANTATTEN_PHILIPS_MAGIC		0x91
#define RTW_BBP_ANTATTEN_INTERSIL_MAGIC		0x92
#define RTW_BBP_ANTATTEN_RFMD_MAGIC		0x93
#define RTW_BBP_ANTATTEN_MAXIM_MAGIC		0xb3
#define	RTW_BBP_ANTATTEN_DFLANTB		0x40
#define	RTW_BBP_ANTATTEN_CHAN14			0x0c

#define RTW_BBP_TRL			0x11	/* guess: transmit/receive
						 * switch latency
						 */
#define RTW_BBP_SYS2			0x12
#define RTW_BBP_SYS2_ANTDIV		0x80	/* enable antenna diversity */
#define RTW_BBP_SYS2_RATE_MASK		__BITS(5,4)	/* loopback rate?
							 * 0: 1Mbps
							 * 1: 2Mbps
							 * 2: 5.5Mbps
							 * 3: 11Mbps
							 */
#define RTW_BBP_SYS3			0x13
/* carrier-sense threshold */
#define RTW_BBP_SYS3_CSTHRESH_MASK	__BITS(0,3)
#define RTW_BBP_CHESTLIM	0x19	/* guess: channel energy-detect
					 * threshold
					 */
#define RTW_BBP_CHSQLIM		0x1a	/* guess: channel signal-quality
					 * threshold
					 */