xref: /src/sys/dev/isa/if_ate.c

/*	$NetBSD: if_ate.c,v 1.45.2.1 2006/11/18 21:34:21 ad Exp $	*/

/*
 * All Rights Reserved, Copyright (C) Fujitsu Limited 1995
 *
 * This software may be used, modified, copied, distributed, and sold, in
 * both source and binary form provided that the above copyright, these
 * terms and the following disclaimer are retained.  The name of the author
 * and/or the contributor may not be used to endorse or promote products
 * derived from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND THE CONTRIBUTOR ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR OR THE CONTRIBUTOR BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION.
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 * SUCH DAMAGE.
 */

/*
 * Portions copyright (C) 1993, David Greenman.  This software may be used,
 * modified, copied, distributed, and sold, in both source and binary form
 * provided that the above copyright and these terms are retained.  Under no
 * circumstances is the author responsible for the proper functioning of this
 * software, nor does the author assume any responsibility for damages
 * incurred with its use.
 */

#include <sys/cdefs.h>
__KERNEL_RCSID(0, "$NetBSD: if_ate.c,v 1.45.2.1 2006/11/18 21:34:21 ad Exp $");

#include <sys/param.h>
#include <sys/systm.h>
#include <sys/device.h>
#include <sys/socket.h>
#include <sys/syslog.h>

#include <net/if.h>
#include <net/if_ether.h>
#include <net/if_media.h>

#include <machine/bus.h>
#include <machine/intr.h>

#include <dev/ic/mb86960reg.h>
#include <dev/ic/mb86960var.h>

#include <dev/isa/isavar.h>

int	ate_match(struct device *, struct cfdata *, void *);
void	ate_attach(struct device *, struct device *, void *);

struct ate_softc {
	struct	mb86960_softc sc_mb86960;	/* real "mb86960" softc */

	/* ISA-specific goo. */
	void	*sc_ih;				/* interrupt cookie */
};

CFATTACH_DECL(ate_isa, sizeof(struct ate_softc),
    ate_match, ate_attach, NULL, NULL);

struct fe_simple_probe_struct {
	uint8_t port;	/* Offset from the base I/O address. */
	uint8_t mask;	/* Bits to be checked. */
	uint8_t bits;	/* Values to be compared against. */
};

static inline int fe_simple_probe(bus_space_tag_t, bus_space_handle_t,
    struct fe_simple_probe_struct const *);
static int ate_find(bus_space_tag_t, bus_space_handle_t, int *, int *);
static int ate_detect(bus_space_tag_t, bus_space_handle_t,
    uint8_t enaddr[ETHER_ADDR_LEN]);

static int const ate_iomap[8] = {
	0x260, 0x280, 0x2A0, 0x240, 0x340, 0x320, 0x380, 0x300
};
#define NATE_IOMAP (sizeof (ate_iomap) / sizeof (ate_iomap[0]))
#define ATE_NPORTS 0x20

#ifdef ATE_DEBUG
#define DPRINTF	printf
#else
#define DPRINTF	while (/*CONSTCOND*/0) printf
#endif

/*
 * Hardware probe routines.
 */

/*
 * Determine if the device is present.
 */
int
ate_match(struct device *parent, struct cfdata *match,
    void *aux)
{
	struct isa_attach_args *ia = aux;
	bus_space_tag_t iot = ia->ia_iot;
	bus_space_handle_t ioh;
	int i, iobase, irq, rv = 0;
	uint8_t myea[ETHER_ADDR_LEN];

	if (ia->ia_nio < 1)
		return 0;
	if (ia->ia_nirq < 1)
		return 0;

	if (ISA_DIRECT_CONFIG(ia))
		return 0;

	/* Disallow wildcarded values. */
	if (ia->ia_io[0].ir_addr == ISA_UNKNOWN_PORT)
		return 0;

	/*
	 * See if the sepcified address is valid for MB86965A JLI mode.
	 */
	for (i = 0; i < NATE_IOMAP; i++)
		if (ate_iomap[i] == ia->ia_io[0].ir_addr)
			break;
	if (i == NATE_IOMAP) {
		DPRINTF("ate_match: unknown iobase 0x%x\n",
		    ia->ia_io[0].ir_addr);
		return 0;
	}

	/* Map i/o space. */
	if (bus_space_map(iot, ia->ia_io[0].ir_addr, ATE_NPORTS, 0, &ioh)) {
		DPRINTF("ate_match: couldn't map iospace 0x%x\n",
		    ia->ia_io[0].ir_addr);
		return 0;
	}

	if (ate_find(iot, ioh, &iobase, &irq) == 0) {
		DPRINTF("ate_match: ate_find failed\n");
		goto out;
	}

	if (iobase != ia->ia_io[0].ir_addr) {
		DPRINTF("ate_match: unexpected iobase in board: 0x%x\n",
		    iobase);
		goto out;
	}

	if (ate_detect(iot, ioh, myea) == 0) { /* XXX necessary? */
		DPRINTF("ate_match: ate_detect failed\n");
		goto out;
	}

	if (ia->ia_irq[0].ir_irq != ISA_UNKNOWN_IRQ) {
		if (ia->ia_irq[0].ir_irq != irq) {
			printf("ate_match: irq mismatch; "
			    "kernel configured %d != board configured %d\n",
			    ia->ia_irq[0].ir_irq, irq);
			goto out;
		}
	} else
		ia->ia_irq[0].ir_irq = irq;

	ia->ia_nio = 1;
	ia->ia_io[0].ir_size = ATE_NPORTS;

	ia->ia_nirq = 1;

	ia->ia_niomem = 0;
	ia->ia_ndrq = 0;

	rv = 1;

 out:
	bus_space_unmap(iot, ioh, ATE_NPORTS);
	return rv;
}

/*
 * Check for specific bits in specific registers have specific values.
 */
static inline int
fe_simple_probe(bus_space_tag_t iot, bus_space_handle_t ioh,
    struct fe_simple_probe_struct const *sp)
{
	uint8_t val;
	struct fe_simple_probe_struct const *p;

	for (p = sp; p->mask != 0; p++) {
		val = bus_space_read_1(iot, ioh, p->port);
		if ((val & p->mask) != p->bits) {
			DPRINTF("fe_simple_probe: %x & %x != %x\n",
			    val, p->mask, p->bits);
			return 0;
		}
	}

	return 1;
}

/*
 * Hardware (vendor) specific probe routines.
 */

/*
 * Probe and initialization for Allied-Telesis AT1700/RE2000 series.
 */
static int
ate_find(bus_space_tag_t iot, bus_space_handle_t ioh, int *iobase, int *irq)
{
	uint8_t eeprom[FE_EEPROM_SIZE];
	int n;

	static int const irqmap[4][4] = {
		{  3,  4,  5,  9 },
		{ 10, 11, 12, 15 },
		{  3, 11,  5, 15 },
		{ 10, 11, 14, 15 },
	};
	static struct fe_simple_probe_struct const probe_table[] = {
		{ FE_DLCR2,  0x70, 0x00 },
		{ FE_DLCR4,  0x08, 0x00 },
		{ FE_DLCR5,  0x80, 0x00 },
#if 0
		{ FE_BMPR16, 0x1B, 0x00 },
		{ FE_BMPR17, 0x7F, 0x00 },
#endif
		{ 0,	     0x00, 0x00 },
	};

#if ATE_DEBUG >= 4
	log(LOG_INFO, "ate_find: probe (0x%x) for ATE\n", iobase);
#if 0
	fe_dump(LOG_INFO, sc);
#endif
#endif

	/*
	 * We should test if MB86965A is on the base address now.
	 * Unfortunately, it is very hard to probe it reliably, since
	 * we have no way to reset the chip under software control.
	 * On cold boot, we could check the "signature" bit patterns
	 * described in the Fujitsu document.  On warm boot, however,
	 * we can predict almost nothing about register values.
	 */
	if (!fe_simple_probe(iot, ioh, probe_table))
		return 0;

	/* Check if our I/O address matches config info on 86965. */
	n = (bus_space_read_1(iot, ioh, FE_BMPR19) & FE_B19_ADDR)
	    >> FE_B19_ADDR_SHIFT;
	*iobase = ate_iomap[n];

	/*
	 * We are now almost sure we have an AT1700 at the given
	 * address.  So, read EEPROM through 86965.  We have to write
	 * into LSI registers to read from EEPROM.  I want to avoid it
	 * at this stage, but I cannot test the presence of the chip
	 * any further without reading EEPROM.  FIXME.
	 */
	mb86965_read_eeprom(iot, ioh, eeprom);

	/* Make sure that config info in EEPROM and 86965 agree. */
	if (eeprom[FE_EEPROM_CONF] != bus_space_read_1(iot, ioh, FE_BMPR19)) {
#ifdef DIAGNOSTIC
		printf("ate_find: "
		    "incorrect configuration in eeprom and chip\n");
#endif
		return 0;
	}

	/*
	 * Try to determine IRQ settings.
	 * Different models use different ranges of IRQs.
	 */
	n = (bus_space_read_1(iot, ioh, FE_BMPR19) & FE_B19_IRQ)
	    >> FE_B19_IRQ_SHIFT;
	switch (eeprom[FE_ATI_EEP_REVISION] & 0xf0) {
	case 0x30:
		*irq = irqmap[3][n];
		break;
	case 0x10:
	case 0x50:
		*irq = irqmap[2][n];
		break;
	case 0x40:
	case 0x60:
		if (eeprom[FE_ATI_EEP_MAGIC] & 0x04) {
			*irq = irqmap[1][n];
			break;
		}
	default:
		*irq = irqmap[0][n];
		break;
	}

	return 1;
}

/*
 * Determine type and ethernet address.
 */
static int
ate_detect(bus_space_tag_t iot, bus_space_handle_t ioh,
    uint8_t enaddr[ETHER_ADDR_LEN])
{
	uint8_t eeprom[FE_EEPROM_SIZE];
	int type;

	/* Get our station address from EEPROM. */
	mb86965_read_eeprom(iot, ioh, eeprom);
	memcpy(enaddr, eeprom + FE_ATI_EEP_ADDR, ETHER_ADDR_LEN);

	/* Make sure we got a valid station address. */
	if ((enaddr[0] & 0x03) != 0x00 ||
	    (enaddr[0] == 0x00 && enaddr[1] == 0x00 && enaddr[2] == 0x00)) {
		DPRINTF("ate_detect: invalid ethernet address\n");
		return 0;
	}

	/*
	 * Determine the card type.
	 */
	switch (eeprom[FE_ATI_EEP_MODEL]) {
	case FE_ATI_MODEL_AT1700T:
		type = FE_TYPE_AT1700T;
		break;
	case FE_ATI_MODEL_AT1700BT:
		type = FE_TYPE_AT1700BT;
		break;
	case FE_ATI_MODEL_AT1700FT:
		type = FE_TYPE_AT1700FT;
		break;
	case FE_ATI_MODEL_AT1700AT:
		type = FE_TYPE_AT1700AT;
		break;
	default:
		type = FE_TYPE_AT_UNKNOWN;
		break;
	}

	return type;
}

void
ate_attach(struct device *parent, struct device *self, void *aux)
{
	struct ate_softc *isc = (struct ate_softc *)self;
	struct mb86960_softc *sc = &isc->sc_mb86960;
	struct isa_attach_args *ia = aux;
	bus_space_tag_t iot = ia->ia_iot;
	bus_space_handle_t ioh;
	uint8_t myea[ETHER_ADDR_LEN];
	const char *typestr;
	int type;

	/* Map i/o space. */
	if (bus_space_map(iot, ia->ia_io[0].ir_addr, ATE_NPORTS, 0, &ioh)) {
		printf(": can't map i/o space\n");
		return;
	}

	sc->sc_bst = iot;
	sc->sc_bsh = ioh;

	/* Determine the card type and get ethernet address. */
	type = ate_detect(iot, ioh, myea);
	switch (type) {
	case FE_TYPE_AT1700T:
		typestr = "AT-1700T/RE2001";
		break;
	case FE_TYPE_AT1700BT:
		typestr = "AT-1700BT/RE2003";
		break;
	case FE_TYPE_AT1700FT:
		typestr = "AT-1700FT/RE2009";
		break;
	case FE_TYPE_AT1700AT:
		typestr = "AT-1700AT/RE2005";
		break;
	case FE_TYPE_AT_UNKNOWN:
		typestr = "unknown AT-1700/RE2000";
		break;

	default:
	  	/* Unknown card type: maybe a new model, but... */
		printf(": where did the card go?!\n");
		panic("unknown card");
	}

	printf(": %s Ethernet\n", typestr);

	/* This interface is always enabled. */
	sc->sc_stat |= FE_STAT_ENABLED;

	/*
	 * Do generic MB86960 attach.
	 */
	mb86960_attach(sc, myea);

	mb86960_config(sc, NULL, 0, 0);

	/* Establish the interrupt handler. */
	isc->sc_ih = isa_intr_establish(ia->ia_ic, ia->ia_irq[0].ir_irq,
	    IST_EDGE, IPL_NET, mb86960_intr, sc);
	if (isc->sc_ih == NULL)
		printf("%s: couldn't establish interrupt handler\n",
		    sc->sc_dev.dv_xname);
}