xref: /src/sys/dev/mii/brgphyreg.h

/*	$NetBSD: brgphyreg.h,v 1.1 2001/06/01 16:50:00 thorpej Exp $	*/

/*
 * Copyright (c) 2000
 *	Bill Paul <wpaul (at) ee.columbia.edu>.  All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. All advertising materials mentioning features or use of this software
 *    must display the following acknowledgement:
 *	This product includes software developed by Bill Paul.
 * 4. Neither the name of the author nor the names of any co-contributors
 *    may be used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
 * THE POSSIBILITY OF SUCH DAMAGE.
 *
 * FreeBSD: src/sys/dev/mii/brgphyreg.h,v 1.1 2000/04/22 01:58:17 wpaul Exp
 */

#ifndef _DEV_MII_BRGPHYREG_H_
#define	_DEV_MII_BRGPHYREG_H_

/*
 * Broadcom BCM5400 registers
 */

#define BRGPHY_MII_PHY_EXTCTL	0x10	/* PHY extended control */
#define BRGPHY_PHY_EXTCTL_MAC_PHY	0x8000	/* 10BIT/GMI-interface */
#define BRGPHY_PHY_EXTCTL_DIS_CROSS	0x4000	/* Disable MDI crossover */
#define BRGPHY_PHY_EXTCTL_TX_DIS	0x2000	/* Tx output disable d*/
#define BRGPHY_PHY_EXTCTL_INT_DIS	0x1000	/* Interrupts disabled */
#define BRGPHY_PHY_EXTCTL_F_INT		0x0800	/* Force interrupt */
#define BRGPHY_PHY_EXTCTL_BY_45		0x0400	/* Bypass 4B5B-Decoder */
#define BRGPHY_PHY_EXTCTL_BY_SCR	0x0200	/* Bypass scrambler */
#define BRGPHY_PHY_EXTCTL_BY_MLT3	0x0100	/* Bypass MLT3 encoder */
#define BRGPHY_PHY_EXTCTL_BY_RXA	0x0080	/* Bypass RX alignment */
#define BRGPHY_PHY_EXTCTL_RES_SCR	0x0040	/* Reset scrambler */
#define BRGPHY_PHY_EXTCTL_EN_LTR	0x0020	/* Enable LED traffic mode */
#define BRGPHY_PHY_EXTCTL_LED_ON	0x0010	/* Force LEDs on */
#define BRGPHY_PHY_EXTCTL_LED_OFF	0x0008	/* Force LEDs off */
#define BRGPHY_PHY_EXTCTL_EX_IPG	0x0004	/* Extended TX IPG mode */
#define BRGPHY_PHY_EXTCTL_3_LED		0x0002	/* Three link LED mode */
#define BRGPHY_PHY_EXTCTL_HIGH_LA	0x0001	/* GMII Fifo Elasticy (?) */

#define BRGPHY_MII_PHY_EXTSTS	0x11	/* PHY extended status */
#define BRGPHY_PHY_EXTSTS_CROSS_STAT	0x2000	/* MDI crossover status */
#define BRGPHY_PHY_EXTSTS_INT_STAT	0x1000	/* Interrupt status */
#define BRGPHY_PHY_EXTSTS_RRS		0x0800	/* Remote receiver status */
#define BRGPHY_PHY_EXTSTS_LRS		0x0400	/* Local receiver status */
#define BRGPHY_PHY_EXTSTS_LOCKED	0x0200	/* Locked */
#define BRGPHY_PHY_EXTSTS_LS		0x0100	/* Link status */
#define BRGPHY_PHY_EXTSTS_RF		0x0080	/* Remove fault */
#define BRGPHY_PHY_EXTSTS_CE_ER		0x0040	/* Carrier ext error */
#define BRGPHY_PHY_EXTSTS_BAD_SSD	0x0020	/* Bad SSD */
#define BRGPHY_PHY_EXTSTS_BAD_ESD	0x0010	/* Bad ESS */
#define BRGPHY_PHY_EXTSTS_RX_ER		0x0008	/* RX error */
#define BRGPHY_PHY_EXTSTS_TX_ER		0x0004	/* TX error */
#define BRGPHY_PHY_EXTSTS_LOCK_ER	0x0002	/* Lock error */
#define BRGPHY_PHY_EXTSTS_MLT3_ER	0x0001	/* MLT3 code error */

#define BRGPHY_MII_RXERRCNT	0x12	/* RX error counter */

#define BRGPHY_MII_FCERRCNT	0x13	/* false carrier sense counter */
#define BGRPHY_FCERRCNT		0x00FF	/* False carrier counter */

#define BRGPHY_MII_RXNOCNT	0x14	/* RX not OK counter */
#define BRGPHY_RXNOCNT_LOCAL	0xFF00	/* Local RX not OK counter */
#define BRGPHY_RXNOCNT_REMOTE	0x00FF	/* Local RX not OK counter */

#define BRGPHY_MII_AUXCTL	0x18	/* AUX control */
#define BRGPHY_AUXCTL_LOW_SQ	0x8000	/* Low squelch */
#define BRGPHY_AUXCTL_LONG_PKT	0x4000	/* RX long packets */
#define BRGPHY_AUXCTL_ER_CTL	0x3000	/* Edgerate control */
#define BRGPHY_AUXCTL_TX_TST	0x0400	/* TX test, always 1 */
#define BRGPHY_AUXCTL_DIS_PRF	0x0080	/* dis part resp filter */
#define BRGPHY_AUXCTL_DIAG_MODE	0x0004	/* Diagnostic mode */

#define BRGPHY_MII_AUXSTS	0x19	/* AUX status */
#define BRGPHY_AUXSTS_ACOMP	0x8000	/* autoneg complete */
#define BRGPHY_AUXSTS_AN_ACK	0x4000	/* autoneg complete ack */
#define BRGPHY_AUXSTS_AN_ACK_D	0x2000	/* autoneg complete ack detect */
#define BRGPHY_AUXSTS_AN_NPW	0x1000	/* autoneg next page wait */
#define BRGPHY_AUXSTS_AN_RES	0x0700	/* AN HDC */
#define BRGPHY_AUXSTS_PDF	0x0080	/* Parallel detect. fault */
#define BRGPHY_AUXSTS_RF	0x0040	/* remote fault */
#define BRGPHY_AUXSTS_ANP_R	0x0020	/* AN page received */
#define BRGPHY_AUXSTS_LP_ANAB	0x0010	/* LP AN ability */
#define BRGPHY_AUXSTS_LP_NPAB	0x0008	/* LP Next page ability */
#define BRGPHY_AUXSTS_LINK	0x0004	/* Link status */
#define BRGPHY_AUXSTS_PRR	0x0002	/* Pause resolution-RX */
#define BRGPHY_AUXSTS_PRT	0x0001	/* Pause resolution-TX */

#define BRGPHY_RES_1000FD	0x0700	/* 1000baseT full duplex */
#define BRGPHY_RES_1000HD	0x0600	/* 1000baseT half duplex */
#define BRGPHY_RES_100FD	0x0500	/* 100baseT full duplex */
#define BRGPHY_RES_100T4	0x0400	/* 100baseT4 */
#define BRGPHY_RES_100HD	0x0300	/* 100baseT half duplex */
#define BRGPHY_RES_10FD		0x0200	/* 10baseT full duplex */
#define BRGPHY_RES_10HD		0x0100	/* 10baseT half duplex */

#define BRGPHY_MII_ISR		0x1A	/* interrupt status */
#define BRGPHY_ISR_PSERR	0x4000	/* Pair swap error */
#define BRGPHY_ISR_MDXI_SC	0x2000	/* MDIX Status Change */
#define BRGPHY_ISR_HCT		0x1000	/* counter above 32K */
#define BRGPHY_ISR_LCT		0x0800	/* all counter below 128 */
#define BRGPHY_ISR_AN_PR	0x0400	/* Autoneg page received */
#define BRGPHY_ISR_NO_HDCL	0x0200	/* No HCD Link */
#define BRGPHY_ISR_NO_HDC	0x0100	/* No HCD */
#define BRGPHY_ISR_USHDC	0x0080	/* Negotiated Unsupported HCD */
#define BRGPHY_ISR_SCR_S_ERR	0x0040	/* Scrambler sync error */
#define BRGPHY_ISR_RRS_CHG	0x0020	/* Remote RX status change */
#define BRGPHY_ISR_LRS_CHG	0x0010	/* Local RX status change */
#define BRGPHY_ISR_DUP_CHG	0x0008	/* Duplex mode change */
#define BRGPHY_ISR_LSP_CHG	0x0004	/* Link speed changed */
#define BRGPHY_ISR_LNK_CHG	0x0002	/* Link status change */
#define BRGPHY_ISR_CRCERR	0x0001	/* CEC error */

#define BRGPHY_MII_IMR		0x1B	/* interrupt mask */
#define BRGPHY_IMR_PSERR	0x4000	/* Pair swap error */
#define BRGPHY_IMR_MDXI_SC	0x2000	/* MDIX Status Change */
#define BRGPHY_IMR_HCT		0x1000	/* counter above 32K */
#define BRGPHY_IMR_LCT		0x0800	/* all counter below 128 */
#define BRGPHY_IMR_AN_PR	0x0400	/* Autoneg page received */
#define BRGPHY_IMR_NO_HDCL	0x0200	/* No HCD Link */
#define BRGPHY_IMR_NO_HDC	0x0100	/* No HCD */
#define BRGPHY_IMR_USHDC	0x0080	/* Negotiated Unsupported HCD */
#define BRGPHY_IMR_SCR_S_ERR	0x0040	/* Scrambler sync error */
#define BRGPHY_IMR_RRS_CHG	0x0020	/* Remote RX status change */
#define BRGPHY_IMR_LRS_CHG	0x0010	/* Local RX status change */
#define BRGPHY_IMR_DUP_CHG	0x0008	/* Duplex mode change */
#define BRGPHY_IMR_LSP_CHG	0x0004	/* Link speed changed */
#define BRGPHY_IMR_LNK_CHG	0x0002	/* Link status change */
#define BRGPHY_IMR_CRCERR	0x0001	/* CEC error */

#define BRGPHY_INTRS	\
	~(BRGPHY_IMR_LNK_CHG|BRGPHY_IMR_LSP_CHG|BRGPHY_IMR_DUP_CHG)

#endif /* _DEV_BRGPHY_MIIREG_H_ */