xref: /src/sys/dev/usb/ehci.c

/*	$NetBSD: ehci.c,v 1.234.2.12 2014/12/03 23:05:06 skrll Exp $ */

/*
 * Copyright (c) 2004-2012 The NetBSD Foundation, Inc.
 * All rights reserved.
 *
 * This code is derived from software contributed to The NetBSD Foundation
 * by Lennart Augustsson (lennart (at) augustsson.net), Charles M. Hannum,
 * Jeremy Morse (jeremy.morse (at) gmail.com), Jared D. McNeill
 * (jmcneill (at) invisible.ca) and Matthew R. Green (mrg (at) eterna.com.au).
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
 * PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 */

/*
 * USB Enhanced Host Controller Driver, a.k.a. USB 2.0 controller.
 *
 * The EHCI 1.0 spec can be found at
 * http://www.intel.com/technology/usb/spec.htm
 * and the USB 2.0 spec at
 * http://www.usb.org/developers/docs/
 *
 */

/*
 * TODO:
 * 1) hold off explorations by companion controllers until ehci has started.
 *
 * 2) The hub driver needs to handle and schedule the transaction translator,
 *    to assign place in frame where different devices get to go. See chapter
 *    on hubs in USB 2.0 for details.
 *
 * 3) Command failures are not recovered correctly.
 */

#include <sys/cdefs.h>
__KERNEL_RCSID(0, "$NetBSD: ehci.c,v 1.234.2.12 2014/12/03 23:05:06 skrll Exp $");

#include "ohci.h"
#include "uhci.h"
#include "opt_usb.h"

#include <sys/param.h>

#include <sys/bus.h>
#include <sys/cpu.h>
#include <sys/device.h>
#include <sys/kernel.h>
#include <sys/kmem.h>
#include <sys/mutex.h>
#include <sys/proc.h>
#include <sys/queue.h>
#include <sys/select.h>
#include <sys/sysctl.h>
#include <sys/systm.h>

#include <machine/endian.h>

#include <dev/usb/usb.h>
#include <dev/usb/usbdi.h>
#include <dev/usb/usbdivar.h>
#include <dev/usb/usbhist.h>
#include <dev/usb/usb_mem.h>
#include <dev/usb/usb_quirks.h>
#include <dev/usb/usbroothub.h>

#include <dev/usb/ehcireg.h>
#include <dev/usb/ehcivar.h>


#ifdef USB_DEBUG
#ifndef EHCI_DEBUG
#define ehcidebug 0
#else
static int ehcidebug = 0;

SYSCTL_SETUP(sysctl_hw_ehci_setup, "sysctl hw.ehci setup")
{
	int err;
	const struct sysctlnode *rnode;
	const struct sysctlnode *cnode;

	err = sysctl_createv(clog, 0, NULL, &rnode,
	    CTLFLAG_PERMANENT, CTLTYPE_NODE, "ehci",
	    SYSCTL_DESCR("ehci global controls"),
	    NULL, 0, NULL, 0, CTL_HW, CTL_CREATE, CTL_EOL);

	if (err)
		goto fail;

	/* control debugging printfs */
	err = sysctl_createv(clog, 0, &rnode, &cnode,
	    CTLFLAG_PERMANENT|CTLFLAG_READWRITE, CTLTYPE_INT,
	    "debug", SYSCTL_DESCR("Enable debugging output"),
	    NULL, 0, &ehcidebug, sizeof(ehcidebug), CTL_CREATE, CTL_EOL);
	if (err)
		goto fail;

	return;
fail:
	aprint_error("%s: sysctl_createv failed (err = %d)\n", __func__, err);
}

#endif /* EHCI_DEBUG */
#endif /* USB_DEBUG */

struct ehci_pipe {
	struct usbd_pipe pipe;
	int nexttoggle;

	ehci_soft_qh_t *sqh;
	union {
		ehci_soft_qtd_t *qtd;
		/* ehci_soft_itd_t *itd; */
		/* ehci_soft_sitd_t *sitd; */
	} tail;
	union {
		/* Control pipe */
		struct {
			usb_dma_t reqdma;
		} ctl;
		/* Interrupt pipe */
		struct {
			u_int length;
		} intr;
		/* Bulk pipe */
		struct {
			u_int length;
		} bulk;
		/* Iso pipe */
		struct {
			u_int next_frame;
			u_int cur_xfers;
		} isoc;
	} u;
};

Static usbd_status	ehci_open(usbd_pipe_handle);
Static void		ehci_poll(struct usbd_bus *);
Static void		ehci_softintr(void *);
Static int		ehci_intr1(ehci_softc_t *);
Static void		ehci_waitintr(ehci_softc_t *, usbd_xfer_handle);
Static void		ehci_check_intr(ehci_softc_t *, struct ehci_xfer *);
Static void		ehci_check_qh_intr(ehci_softc_t *, struct ehci_xfer *);
Static void		ehci_check_itd_intr(ehci_softc_t *, struct ehci_xfer *);
Static void		ehci_check_sitd_intr(ehci_softc_t *, struct ehci_xfer *);
Static void		ehci_idone(struct ehci_xfer *);
Static void		ehci_timeout(void *);
Static void		ehci_timeout_task(void *);
Static void		ehci_intrlist_timeout(void *);
Static void		ehci_doorbell(void *);
Static void		ehci_pcd(void *);

Static usbd_xfer_handle	ehci_allocx(struct usbd_bus *);
Static void		ehci_freex(struct usbd_bus *, usbd_xfer_handle);
Static void		ehci_get_lock(struct usbd_bus *, kmutex_t **);

Static usbd_status	ehci_root_ctrl_transfer(usbd_xfer_handle);
Static usbd_status	ehci_root_ctrl_start(usbd_xfer_handle);
Static void		ehci_root_ctrl_abort(usbd_xfer_handle);
Static void		ehci_root_ctrl_close(usbd_pipe_handle);
Static void		ehci_root_ctrl_done(usbd_xfer_handle);

Static usbd_status	ehci_root_intr_transfer(usbd_xfer_handle);
Static usbd_status	ehci_root_intr_start(usbd_xfer_handle);
Static void		ehci_root_intr_abort(usbd_xfer_handle);
Static void		ehci_root_intr_close(usbd_pipe_handle);
Static void		ehci_root_intr_done(usbd_xfer_handle);

Static usbd_status	ehci_device_ctrl_transfer(usbd_xfer_handle);
Static usbd_status	ehci_device_ctrl_start(usbd_xfer_handle);
Static void		ehci_device_ctrl_abort(usbd_xfer_handle);
Static void		ehci_device_ctrl_close(usbd_pipe_handle);
Static void		ehci_device_ctrl_done(usbd_xfer_handle);

Static usbd_status	ehci_device_bulk_transfer(usbd_xfer_handle);
Static usbd_status	ehci_device_bulk_start(usbd_xfer_handle);
Static void		ehci_device_bulk_abort(usbd_xfer_handle);
Static void		ehci_device_bulk_close(usbd_pipe_handle);
Static void		ehci_device_bulk_done(usbd_xfer_handle);

Static usbd_status	ehci_device_intr_transfer(usbd_xfer_handle);
Static usbd_status	ehci_device_intr_start(usbd_xfer_handle);
Static void		ehci_device_intr_abort(usbd_xfer_handle);
Static void		ehci_device_intr_close(usbd_pipe_handle);
Static void		ehci_device_intr_done(usbd_xfer_handle);

Static usbd_status	ehci_device_isoc_transfer(usbd_xfer_handle);
Static usbd_status	ehci_device_isoc_start(usbd_xfer_handle);
Static void		ehci_device_isoc_abort(usbd_xfer_handle);
Static void		ehci_device_isoc_close(usbd_pipe_handle);
Static void		ehci_device_isoc_done(usbd_xfer_handle);

Static usbd_status	ehci_device_fs_isoc_transfer(usbd_xfer_handle);
Static usbd_status	ehci_device_fs_isoc_start(usbd_xfer_handle);
Static void		ehci_device_fs_isoc_abort(usbd_xfer_handle);
Static void		ehci_device_fs_isoc_close(usbd_pipe_handle);
Static void		ehci_device_fs_isoc_done(usbd_xfer_handle);

Static void		ehci_device_clear_toggle(usbd_pipe_handle pipe);
Static void		ehci_noop(usbd_pipe_handle pipe);

Static void		ehci_disown(ehci_softc_t *, int, int);

Static ehci_soft_qh_t  *ehci_alloc_sqh(ehci_softc_t *);
Static void		ehci_free_sqh(ehci_softc_t *, ehci_soft_qh_t *);

Static ehci_soft_qtd_t  *ehci_alloc_sqtd(ehci_softc_t *);
Static void		ehci_free_sqtd(ehci_softc_t *, ehci_soft_qtd_t *);
Static usbd_status	ehci_alloc_sqtd_chain(struct ehci_pipe *,
			    ehci_softc_t *, int, int, usbd_xfer_handle,
			    ehci_soft_qtd_t **, ehci_soft_qtd_t **);
Static void		ehci_free_sqtd_chain(ehci_softc_t *, ehci_soft_qtd_t *,
					    ehci_soft_qtd_t *);

Static ehci_soft_itd_t	*ehci_alloc_itd(ehci_softc_t *sc);
Static ehci_soft_sitd_t *ehci_alloc_sitd(ehci_softc_t *sc);
Static void		ehci_free_itd(ehci_softc_t *sc, ehci_soft_itd_t *itd);
Static void		ehci_free_sitd(ehci_softc_t *sc, ehci_soft_sitd_t *);
Static void 		ehci_rem_free_itd_chain(ehci_softc_t *sc,
						struct ehci_xfer *exfer);
Static void		ehci_rem_free_sitd_chain(ehci_softc_t *sc,
						 struct ehci_xfer *exfer);
Static void 		ehci_abort_isoc_xfer(usbd_xfer_handle xfer,
						usbd_status status);

Static usbd_status	ehci_device_request(usbd_xfer_handle xfer);

Static usbd_status	ehci_device_setintr(ehci_softc_t *, ehci_soft_qh_t *,
			    int ival);

Static void		ehci_add_qh(ehci_softc_t *, ehci_soft_qh_t *,
				    ehci_soft_qh_t *);
Static void		ehci_rem_qh(ehci_softc_t *, ehci_soft_qh_t *,
				    ehci_soft_qh_t *);
Static void		ehci_set_qh_qtd(ehci_soft_qh_t *, ehci_soft_qtd_t *);
Static void		ehci_sync_hc(ehci_softc_t *);

Static void		ehci_close_pipe(usbd_pipe_handle, ehci_soft_qh_t *);
Static void		ehci_abort_xfer(usbd_xfer_handle, usbd_status);

#ifdef EHCI_DEBUG
Static ehci_softc_t 	*theehci;
void			ehci_dump(void);
#endif

#ifdef EHCI_DEBUG
Static void		ehci_dump_regs(ehci_softc_t *);
Static void		ehci_dump_sqtds(ehci_soft_qtd_t *);
Static void		ehci_dump_sqtd(ehci_soft_qtd_t *);
Static void		ehci_dump_qtd(ehci_qtd_t *);
Static void		ehci_dump_sqh(ehci_soft_qh_t *);
Static void		ehci_dump_sitd(struct ehci_soft_itd *itd);
Static void		ehci_dump_itd(struct ehci_soft_itd *);
Static void		ehci_dump_exfer(struct ehci_xfer *);
#endif

#define EHCI_NULL htole32(EHCI_LINK_TERMINATE)

#define EHCI_INTR_ENDPT 1

#define ehci_add_intr_list(sc, ex) \
	TAILQ_INSERT_TAIL(&(sc)->sc_intrhead, (ex), inext);
#define ehci_del_intr_list(sc, ex) \
	do { \
		TAILQ_REMOVE(&sc->sc_intrhead, (ex), inext); \
		(ex)->inext.tqe_prev = NULL; \
	} while (0)
#define ehci_active_intr_list(ex) ((ex)->inext.tqe_prev != NULL)

Static const struct usbd_bus_methods ehci_bus_methods = {
	.ubm_open =	ehci_open,
	.ubm_softint =	ehci_softintr,
	.ubm_dopoll =	ehci_poll,
	.ubm_allocx =	ehci_allocx,
	.ubm_freex =	ehci_freex,
	.ubm_getlock =	ehci_get_lock,
	.ubm_newdev =	NULL,
};

Static const struct usbd_pipe_methods ehci_root_ctrl_methods = {
	.upm_transfer =	ehci_root_ctrl_transfer,
	.upm_start =	ehci_root_ctrl_start,
	.upm_abort =	ehci_root_ctrl_abort,
	.upm_close =	ehci_root_ctrl_close,
	.upm_cleartoggle =	ehci_noop,
	.upm_done =		ehci_root_ctrl_done,
};

Static const struct usbd_pipe_methods ehci_root_intr_methods = {
	.upm_transfer =	ehci_root_intr_transfer,
	.upm_start =	ehci_root_intr_start,
	.upm_abort =	ehci_root_intr_abort,
	.upm_close =	ehci_root_intr_close,
	.upm_cleartoggle =	ehci_noop,
	.upm_done =	ehci_root_intr_done,
};

Static const struct usbd_pipe_methods ehci_device_ctrl_methods = {
	.upm_transfer =	ehci_device_ctrl_transfer,
	.upm_start =	ehci_device_ctrl_start,
	.upm_abort =	ehci_device_ctrl_abort,
	.upm_close =	ehci_device_ctrl_close,
	.upm_cleartoggle =	ehci_noop,
	.upm_done =	ehci_device_ctrl_done,
};

Static const struct usbd_pipe_methods ehci_device_intr_methods = {
	.upm_transfer =	ehci_device_intr_transfer,
	.upm_start =	ehci_device_intr_start,
	.upm_abort =	ehci_device_intr_abort,
	.upm_close =	ehci_device_intr_close,
	.upm_cleartoggle =	ehci_device_clear_toggle,
	.upm_done =	ehci_device_intr_done,
};

Static const struct usbd_pipe_methods ehci_device_bulk_methods = {
	.upm_transfer =	ehci_device_bulk_transfer,
	.upm_start =	ehci_device_bulk_start,
	.upm_abort =	ehci_device_bulk_abort,
	.upm_close =	ehci_device_bulk_close,
	.upm_cleartoggle =	ehci_device_clear_toggle,
	.upm_done =	ehci_device_bulk_done,
};

Static const struct usbd_pipe_methods ehci_device_isoc_methods = {
	.upm_transfer =	ehci_device_isoc_transfer,
	.upm_start =	ehci_device_isoc_start,
	.upm_abort =	ehci_device_isoc_abort,
	.upm_close =	ehci_device_isoc_close,
	.upm_cleartoggle =	ehci_noop,
	.upm_done =	ehci_device_isoc_done,
};

Static const struct usbd_pipe_methods ehci_device_fs_isoc_methods = {
	.upm_transfer =	ehci_device_fs_isoc_transfer,
	.upm_start =	ehci_device_fs_isoc_start,
	.upm_abort =	ehci_device_fs_isoc_abort,
	.upm_close =	ehci_device_fs_isoc_close,
	.upm_cleartoggle = ehci_noop,
	.upm_done =	ehci_device_fs_isoc_done,
};

static const uint8_t revbits[EHCI_MAX_POLLRATE] = {
0x00,0x40,0x20,0x60,0x10,0x50,0x30,0x70,0x08,0x48,0x28,0x68,0x18,0x58,0x38,0x78,
0x04,0x44,0x24,0x64,0x14,0x54,0x34,0x74,0x0c,0x4c,0x2c,0x6c,0x1c,0x5c,0x3c,0x7c,
0x02,0x42,0x22,0x62,0x12,0x52,0x32,0x72,0x0a,0x4a,0x2a,0x6a,0x1a,0x5a,0x3a,0x7a,
0x06,0x46,0x26,0x66,0x16,0x56,0x36,0x76,0x0e,0x4e,0x2e,0x6e,0x1e,0x5e,0x3e,0x7e,
0x01,0x41,0x21,0x61,0x11,0x51,0x31,0x71,0x09,0x49,0x29,0x69,0x19,0x59,0x39,0x79,
0x05,0x45,0x25,0x65,0x15,0x55,0x35,0x75,0x0d,0x4d,0x2d,0x6d,0x1d,0x5d,0x3d,0x7d,
0x03,0x43,0x23,0x63,0x13,0x53,0x33,0x73,0x0b,0x4b,0x2b,0x6b,0x1b,0x5b,0x3b,0x7b,
0x07,0x47,0x27,0x67,0x17,0x57,0x37,0x77,0x0f,0x4f,0x2f,0x6f,0x1f,0x5f,0x3f,0x7f,
};

usbd_status
ehci_init(ehci_softc_t *sc)
{
	uint32_t vers, sparams, cparams, hcr;
	u_int i;
	usbd_status err;
	ehci_soft_qh_t *sqh;
	u_int ncomp;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);
#ifdef EHCI_DEBUG
	theehci = sc;
#endif

	mutex_init(&sc->sc_lock, MUTEX_DEFAULT, IPL_SOFTUSB);
	mutex_init(&sc->sc_intr_lock, MUTEX_DEFAULT, IPL_SCHED);
	cv_init(&sc->sc_softwake_cv, "ehciab");
	cv_init(&sc->sc_doorbell, "ehcidi");

	sc->sc_xferpool = pool_cache_init(sizeof(struct ehci_xfer), 0, 0, 0,
	    "ehcixfer", NULL, IPL_USB, NULL, NULL, NULL);

	sc->sc_doorbell_si = softint_establish(SOFTINT_NET | SOFTINT_MPSAFE,
	    ehci_doorbell, sc);
	KASSERT(sc->sc_doorbell_si != NULL);
	sc->sc_pcd_si = softint_establish(SOFTINT_NET | SOFTINT_MPSAFE,
	    ehci_pcd, sc);
	KASSERT(sc->sc_pcd_si != NULL);

	sc->sc_offs = EREAD1(sc, EHCI_CAPLENGTH);

	vers = EREAD2(sc, EHCI_HCIVERSION);
	aprint_verbose("%s: EHCI version %x.%x\n", device_xname(sc->sc_dev),
	       vers >> 8, vers & 0xff);

	sparams = EREAD4(sc, EHCI_HCSPARAMS);
	USBHIST_LOG(ehcidebug, "sparams=%#x", sparams, 0, 0, 0);
	sc->sc_npcomp = EHCI_HCS_N_PCC(sparams);
	ncomp = EHCI_HCS_N_CC(sparams);
	if (ncomp != sc->sc_ncomp) {
		aprint_verbose("%s: wrong number of companions (%d != %d)\n",
			       device_xname(sc->sc_dev), ncomp, sc->sc_ncomp);
#if NOHCI == 0 || NUHCI == 0
		aprint_error("%s: ohci or uhci probably not configured\n",
			     device_xname(sc->sc_dev));
#endif
		if (ncomp < sc->sc_ncomp)
			sc->sc_ncomp = ncomp;
	}
	if (sc->sc_ncomp > 0) {
		KASSERT(!(sc->sc_flags & EHCIF_ETTF));
		aprint_normal("%s: companion controller%s, %d port%s each:",
		    device_xname(sc->sc_dev), sc->sc_ncomp!=1 ? "s" : "",
		    EHCI_HCS_N_PCC(sparams),
		    EHCI_HCS_N_PCC(sparams)!=1 ? "s" : "");
		for (i = 0; i < sc->sc_ncomp; i++)
			aprint_normal(" %s", device_xname(sc->sc_comps[i]));
		aprint_normal("\n");
	}
	sc->sc_noport = EHCI_HCS_N_PORTS(sparams);
	cparams = EREAD4(sc, EHCI_HCCPARAMS);
	USBHIST_LOG(ehcidebug, "cparams=%#x", cparams, 0, 0, 0);
	sc->sc_hasppc = EHCI_HCS_PPC(sparams);

	if (EHCI_HCC_64BIT(cparams)) {
		/* MUST clear segment register if 64 bit capable. */
		EWRITE4(sc, EHCI_CTRLDSSEGMENT, 0);
	}

	sc->sc_bus.ub_revision = USBREV_2_0;
	sc->sc_bus.ub_usedma = true;
	sc->sc_bus.ub_dmaflags = USBMALLOC_MULTISEG;

	/* Reset the controller */
	USBHIST_LOG(ehcidebug, "resetting", 0, 0, 0, 0);
	EOWRITE4(sc, EHCI_USBCMD, 0);	/* Halt controller */
	usb_delay_ms(&sc->sc_bus, 1);
	EOWRITE4(sc, EHCI_USBCMD, EHCI_CMD_HCRESET);
	for (i = 0; i < 100; i++) {
		usb_delay_ms(&sc->sc_bus, 1);
		hcr = EOREAD4(sc, EHCI_USBCMD) & EHCI_CMD_HCRESET;
		if (!hcr)
			break;
	}
	if (hcr) {
		aprint_error("%s: reset timeout\n", device_xname(sc->sc_dev));
		return (USBD_IOERROR);
	}
	if (sc->sc_vendor_init)
		sc->sc_vendor_init(sc);

	/*
	 * If we are doing embedded transaction translation function, force
	 * the controller to host mode.
	 */
	if (sc->sc_flags & EHCIF_ETTF) {
		uint32_t usbmode = EREAD4(sc, EHCI_USBMODE);
		usbmode &= ~EHCI_USBMODE_CM;
		usbmode |= EHCI_USBMODE_CM_HOST;
		EWRITE4(sc, EHCI_USBMODE, usbmode);
	}

	/* XXX need proper intr scheduling */
	sc->sc_rand = 96;

	/* frame list size at default, read back what we got and use that */
	switch (EHCI_CMD_FLS(EOREAD4(sc, EHCI_USBCMD))) {
	case 0: sc->sc_flsize = 1024; break;
	case 1: sc->sc_flsize = 512; break;
	case 2: sc->sc_flsize = 256; break;
	case 3: return (USBD_IOERROR);
	}
	err = usb_allocmem(&sc->sc_bus, sc->sc_flsize * sizeof(ehci_link_t),
	    EHCI_FLALIGN_ALIGN, &sc->sc_fldma);
	if (err)
		return (err);
	USBHIST_LOG(ehcidebug, "flsize=%d", sc->sc_flsize, 0, 0, 0);
	sc->sc_flist = KERNADDR(&sc->sc_fldma, 0);

	for (i = 0; i < sc->sc_flsize; i++) {
		sc->sc_flist[i] = EHCI_NULL;
	}

	EOWRITE4(sc, EHCI_PERIODICLISTBASE, DMAADDR(&sc->sc_fldma, 0));

	sc->sc_softitds = kmem_zalloc(sc->sc_flsize * sizeof(ehci_soft_itd_t *),
				     KM_SLEEP);
	if (sc->sc_softitds == NULL)
		return ENOMEM;
	LIST_INIT(&sc->sc_freeitds);
	LIST_INIT(&sc->sc_freesitds);
	TAILQ_INIT(&sc->sc_intrhead);

	/* Set up the bus struct. */
	sc->sc_bus.ub_methods = &ehci_bus_methods;
	sc->sc_bus.ub_pipesize= sizeof(struct ehci_pipe);

	sc->sc_eintrs = EHCI_NORMAL_INTRS;

	/*
	 * Allocate the interrupt dummy QHs. These are arranged to give poll
	 * intervals that are powers of 2 times 1ms.
	 */
	for (i = 0; i < EHCI_INTRQHS; i++) {
		sqh = ehci_alloc_sqh(sc);
		if (sqh == NULL) {
			err = USBD_NOMEM;
			goto bad1;
		}
		sc->sc_islots[i].sqh = sqh;
	}
	for (i = 0; i < EHCI_INTRQHS; i++) {
		sqh = sc->sc_islots[i].sqh;
		if (i == 0) {
			/* The last (1ms) QH terminates. */
			sqh->qh.qh_link = EHCI_NULL;
			sqh->next = NULL;
		} else {
			/* Otherwise the next QH has half the poll interval */
			sqh->next = sc->sc_islots[(i + 1) / 2 - 1].sqh;
			sqh->qh.qh_link = htole32(sqh->next->physaddr |
			    EHCI_LINK_QH);
		}
		sqh->qh.qh_endp = htole32(EHCI_QH_SET_EPS(EHCI_QH_SPEED_HIGH));
		sqh->qh.qh_curqtd = EHCI_NULL;
		sqh->next = NULL;
		sqh->qh.qh_qtd.qtd_next = EHCI_NULL;
		sqh->qh.qh_qtd.qtd_altnext = EHCI_NULL;
		sqh->qh.qh_qtd.qtd_status = htole32(EHCI_QTD_HALTED);
		sqh->sqtd = NULL;
		usb_syncmem(&sqh->dma, sqh->offs, sizeof(sqh->qh),
		    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
	}
	/* Point the frame list at the last level (128ms). */
	for (i = 0; i < sc->sc_flsize; i++) {
		int j;

		j = (i & ~(EHCI_MAX_POLLRATE-1)) |
		    revbits[i & (EHCI_MAX_POLLRATE-1)];
		sc->sc_flist[j] = htole32(EHCI_LINK_QH |
		    sc->sc_islots[EHCI_IQHIDX(EHCI_IPOLLRATES - 1,
		    i)].sqh->physaddr);
	}
	usb_syncmem(&sc->sc_fldma, 0, sc->sc_flsize * sizeof(ehci_link_t),
	    BUS_DMASYNC_PREWRITE);

	/* Allocate dummy QH that starts the async list. */
	sqh = ehci_alloc_sqh(sc);
	if (sqh == NULL) {
		err = USBD_NOMEM;
		goto bad1;
	}
	/* Fill the QH */
	sqh->qh.qh_endp =
	    htole32(EHCI_QH_SET_EPS(EHCI_QH_SPEED_HIGH) | EHCI_QH_HRECL);
	sqh->qh.qh_link =
	    htole32(sqh->physaddr | EHCI_LINK_QH);
	sqh->qh.qh_curqtd = EHCI_NULL;
	sqh->next = NULL;
	/* Fill the overlay qTD */
	sqh->qh.qh_qtd.qtd_next = EHCI_NULL;
	sqh->qh.qh_qtd.qtd_altnext = EHCI_NULL;
	sqh->qh.qh_qtd.qtd_status = htole32(EHCI_QTD_HALTED);
	sqh->sqtd = NULL;
	usb_syncmem(&sqh->dma, sqh->offs, sizeof(sqh->qh),
	    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
#ifdef EHCI_DEBUG
	ehci_dump_sqh(sqh);
#endif

	/* Point to async list */
	sc->sc_async_head = sqh;
	EOWRITE4(sc, EHCI_ASYNCLISTADDR, sqh->physaddr | EHCI_LINK_QH);

	callout_init(&sc->sc_tmo_intrlist, CALLOUT_MPSAFE);

	/* Turn on controller */
	EOWRITE4(sc, EHCI_USBCMD,
		 EHCI_CMD_ITC_2 | /* 2 microframes interrupt delay */
		 (EOREAD4(sc, EHCI_USBCMD) & EHCI_CMD_FLS_M) |
		 EHCI_CMD_ASE |
		 EHCI_CMD_PSE |
		 EHCI_CMD_RS);

	/* Take over port ownership */
	EOWRITE4(sc, EHCI_CONFIGFLAG, EHCI_CONF_CF);

	for (i = 0; i < 100; i++) {
		usb_delay_ms(&sc->sc_bus, 1);
		hcr = EOREAD4(sc, EHCI_USBSTS) & EHCI_STS_HCH;
		if (!hcr)
			break;
	}
	if (hcr) {
		aprint_error("%s: run timeout\n", device_xname(sc->sc_dev));
		return (USBD_IOERROR);
	}

	/* Enable interrupts */
	USBHIST_LOG(ehcidebug, "enabling interupts", 0, 0, 0, 0);
	EOWRITE4(sc, EHCI_USBINTR, sc->sc_eintrs);

	return (USBD_NORMAL_COMPLETION);

#if 0
 bad2:
	ehci_free_sqh(sc, sc->sc_async_head);
#endif
 bad1:
	usb_freemem(&sc->sc_bus, &sc->sc_fldma);
	return (err);
}

int
ehci_intr(void *v)
{
	ehci_softc_t *sc = v;
	int ret = 0;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	if (sc == NULL)
		return 0;

	mutex_spin_enter(&sc->sc_intr_lock);

	if (sc->sc_dying || !device_has_power(sc->sc_dev))
		goto done;

	/* If we get an interrupt while polling, then just ignore it. */
	if (sc->sc_bus.ub_usepolling) {
		uint32_t intrs = EHCI_STS_INTRS(EOREAD4(sc, EHCI_USBSTS));

		if (intrs)
			EOWRITE4(sc, EHCI_USBSTS, intrs); /* Acknowledge */
#ifdef DIAGNOSTIC
		USBHIST_LOGN(ehcidebug, 16,
		    "ignored interrupt while polling", 0, 0, 0, 0);
#endif
		goto done;
	}

	ret = ehci_intr1(sc);

done:
	mutex_spin_exit(&sc->sc_intr_lock);
	return ret;
}

Static int
ehci_intr1(ehci_softc_t *sc)
{
	uint32_t intrs, eintrs;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	/* In case the interrupt occurs before initialization has completed. */
	if (sc == NULL) {
#ifdef DIAGNOSTIC
		printf("ehci_intr1: sc == NULL\n");
#endif
		return (0);
	}

	KASSERT(mutex_owned(&sc->sc_intr_lock));

	intrs = EHCI_STS_INTRS(EOREAD4(sc, EHCI_USBSTS));
	if (!intrs)
		return (0);

	eintrs = intrs & sc->sc_eintrs;
	USBHIST_LOG(ehcidebug, "sc=%p intrs=%#x(%#x) eintrs=%#x",
	    sc, intrs, EOREAD4(sc, EHCI_USBSTS), eintrs);
	if (!eintrs)
		return (0);

	EOWRITE4(sc, EHCI_USBSTS, intrs); /* Acknowledge */
	if (eintrs & EHCI_STS_IAA) {
		USBHIST_LOG(ehcidebug, "door bell", 0, 0, 0, 0);
		kpreempt_disable();
		KASSERT(sc->sc_doorbell_si != NULL);
		softint_schedule(sc->sc_doorbell_si);
		kpreempt_enable();
		eintrs &= ~EHCI_STS_IAA;
	}
	if (eintrs & (EHCI_STS_INT | EHCI_STS_ERRINT)) {
		USBHIST_LOG(ehcidebug, "INT=%d  ERRINT=%d",
		    eintrs & EHCI_STS_INT ? 1 : 0,
		    eintrs & EHCI_STS_ERRINT ? 1 : 0, 0, 0);
		usb_schedsoftintr(&sc->sc_bus);
		eintrs &= ~(EHCI_STS_INT | EHCI_STS_ERRINT);
	}
	if (eintrs & EHCI_STS_HSE) {
		printf("%s: unrecoverable error, controller halted\n",
		       device_xname(sc->sc_dev));
		/* XXX what else */
	}
	if (eintrs & EHCI_STS_PCD) {
		kpreempt_disable();
		KASSERT(sc->sc_pcd_si != NULL);
		softint_schedule(sc->sc_pcd_si);
		kpreempt_enable();
		eintrs &= ~EHCI_STS_PCD;
	}

	if (eintrs != 0) {
		/* Block unprocessed interrupts. */
		sc->sc_eintrs &= ~eintrs;
		EOWRITE4(sc, EHCI_USBINTR, sc->sc_eintrs);
		printf("%s: blocking intrs 0x%x\n",
		       device_xname(sc->sc_dev), eintrs);
	}

	return (1);
}

Static void
ehci_doorbell(void *addr)
{
	ehci_softc_t *sc = addr;

	mutex_enter(&sc->sc_lock);
	cv_broadcast(&sc->sc_doorbell);
	mutex_exit(&sc->sc_lock);
}

Static void
ehci_pcd(void *addr)
{
	ehci_softc_t *sc = addr;
	usbd_xfer_handle xfer;
	u_char *p;
	int i, m;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	mutex_enter(&sc->sc_lock);
	xfer = sc->sc_intrxfer;

	if (xfer == NULL) {
		/* Just ignore the change. */
		goto done;
	}

	p = xfer->ux_buf;
	m = min(sc->sc_noport, xfer->ux_length * 8 - 1);
	memset(p, 0, xfer->ux_length);
	for (i = 1; i <= m; i++) {
		/* Pick out CHANGE bits from the status reg. */
		if (EOREAD4(sc, EHCI_PORTSC(i)) & EHCI_PS_CLEAR)
			p[i/8] |= 1 << (i%8);
		if (i % 8 == 7)
			USBHIST_LOG(ehcidebug, "change(%d)=0x%02x", i / 8,
			    p[i/8], 0, 0);
	}
	xfer->ux_actlen = xfer->ux_length;
	xfer->ux_status = USBD_NORMAL_COMPLETION;

	usb_transfer_complete(xfer);

done:
	mutex_exit(&sc->sc_lock);
}

Static void
ehci_softintr(void *v)
{
	struct usbd_bus *bus = v;
	ehci_softc_t *sc = bus->ub_hcpriv;
	struct ehci_xfer *ex, *nextex;

	KASSERT(sc->sc_bus.ub_usepolling || mutex_owned(&sc->sc_lock));

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	/*
	 * The only explanation I can think of for why EHCI is as brain dead
	 * as UHCI interrupt-wise is that Intel was involved in both.
	 * An interrupt just tells us that something is done, we have no
	 * clue what, so we need to scan through all active transfers. :-(
	 */
	for (ex = TAILQ_FIRST(&sc->sc_intrhead); ex; ex = nextex) {
		nextex = TAILQ_NEXT(ex, inext);
		ehci_check_intr(sc, ex);
	}

	/* Schedule a callout to catch any dropped transactions. */
	if ((sc->sc_flags & EHCIF_DROPPED_INTR_WORKAROUND) &&
	    !TAILQ_EMPTY(&sc->sc_intrhead))
		callout_reset(&sc->sc_tmo_intrlist,
		    hz, ehci_intrlist_timeout, sc);

	if (sc->sc_softwake) {
		sc->sc_softwake = 0;
		cv_broadcast(&sc->sc_softwake_cv);
	}
}

/* Check for an interrupt. */
Static void
ehci_check_intr(ehci_softc_t *sc, struct ehci_xfer *ex)
{
	usbd_device_handle dev = ex->xfer.ux_pipe->up_dev;
	int attr;

	USBHIST_FUNC();	USBHIST_CALLED(ehcidebug);
	USBHIST_LOG(ehcidebug, "ex = %p", ex, 0, 0, 0);

	KASSERT(sc->sc_bus.ub_usepolling || mutex_owned(&sc->sc_lock));

	attr = ex->xfer.ux_pipe->up_endpoint->ue_edesc->bmAttributes;
	if (UE_GET_XFERTYPE(attr) == UE_ISOCHRONOUS) {
		if (dev->ud_speed == USB_SPEED_HIGH)
			ehci_check_itd_intr(sc, ex);
		else
			ehci_check_sitd_intr(sc, ex);
	} else
		ehci_check_qh_intr(sc, ex);

	return;
}

Static void
ehci_check_qh_intr(ehci_softc_t *sc, struct ehci_xfer *ex)
{
	ehci_soft_qtd_t *sqtd, *lsqtd;
	uint32_t status;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	KASSERT(sc->sc_bus.ub_usepolling || mutex_owned(&sc->sc_lock));

	if (ex->sqtdstart == NULL) {
		printf("ehci_check_qh_intr: not valid sqtd\n");
		return;
	}

	lsqtd = ex->sqtdend;
#ifdef DIAGNOSTIC
	if (lsqtd == NULL) {
		printf("ehci_check_qh_intr: lsqtd==0\n");
		return;
	}
#endif
	/*
	 * If the last TD is still active we need to check whether there
	 * is an error somewhere in the middle, or whether there was a
	 * short packet (SPD and not ACTIVE).
	 */
	usb_syncmem(&lsqtd->dma,
	    lsqtd->offs + offsetof(ehci_qtd_t, qtd_status),
	    sizeof(lsqtd->qtd.qtd_status),
	    BUS_DMASYNC_POSTWRITE | BUS_DMASYNC_POSTREAD);
	status = le32toh(lsqtd->qtd.qtd_status);
	usb_syncmem(&lsqtd->dma,
	    lsqtd->offs + offsetof(ehci_qtd_t, qtd_status),
	    sizeof(lsqtd->qtd.qtd_status), BUS_DMASYNC_PREREAD);
	if (status & EHCI_QTD_ACTIVE) {
		USBHIST_LOGN(ehcidebug, 10, "active ex=%p", ex, 0, 0, 0);
		for (sqtd = ex->sqtdstart; sqtd != lsqtd; sqtd=sqtd->nextqtd) {
			usb_syncmem(&sqtd->dma,
			    sqtd->offs + offsetof(ehci_qtd_t, qtd_status),
			    sizeof(sqtd->qtd.qtd_status),
			    BUS_DMASYNC_POSTWRITE | BUS_DMASYNC_POSTREAD);
			status = le32toh(sqtd->qtd.qtd_status);
			usb_syncmem(&sqtd->dma,
			    sqtd->offs + offsetof(ehci_qtd_t, qtd_status),
			    sizeof(sqtd->qtd.qtd_status), BUS_DMASYNC_PREREAD);
			/* If there's an active QTD the xfer isn't done. */
			if (status & EHCI_QTD_ACTIVE)
				break;
			/* Any kind of error makes the xfer done. */
			if (status & EHCI_QTD_HALTED)
				goto done;
			/* Handle short packets */
			if (EHCI_QTD_GET_BYTES(status) != 0) {
				usbd_pipe_handle pipe = ex->xfer.ux_pipe;
				usb_endpoint_descriptor_t *ed =
				    pipe->up_endpoint->ue_edesc;
				uint8_t xt = UE_GET_XFERTYPE(ed->bmAttributes);

				/*
				 * If we get here for a control transfer then
				 * we need to let the hardware complete the
				 * status phase.  That is, we're not done
				 * quite yet.
				 *
				 * Otherwise, we're done.
				 */
				if (xt == UE_CONTROL) {
					break;
				}
				goto done;
			}
		}
		USBHIST_LOGN(ehcidebug, 10, "ex=%p std=%p still active",
		    ex, ex->sqtdstart, 0, 0);
		return;
	}
 done:
	USBHIST_LOGN(ehcidebug, 10, "ex=%p done", ex, 0, 0, 0);
	callout_stop(&ex->xfer.ux_callout);
	ehci_idone(ex);
}

Static void
ehci_check_itd_intr(ehci_softc_t *sc, struct ehci_xfer *ex)
{
	ehci_soft_itd_t *itd;
	int i;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	KASSERT(mutex_owned(&sc->sc_lock));

	if (&ex->xfer != SIMPLEQ_FIRST(&ex->xfer.ux_pipe->up_queue))
		return;

	if (ex->itdstart == NULL) {
		printf("ehci_check_itd_intr: not valid itd\n");
		return;
	}

	itd = ex->itdend;
#ifdef DIAGNOSTIC
	if (itd == NULL) {
		printf("ehci_check_itd_intr: itdend == 0\n");
		return;
	}
#endif

	/*
	 * check no active transfers in last itd, meaning we're finished
	 */

	usb_syncmem(&itd->dma, itd->offs + offsetof(ehci_itd_t, itd_ctl),
		    sizeof(itd->itd.itd_ctl), BUS_DMASYNC_POSTWRITE |
		    BUS_DMASYNC_POSTREAD);

	for (i = 0; i < EHCI_ITD_NUFRAMES; i++) {
		if (le32toh(itd->itd.itd_ctl[i]) & EHCI_ITD_ACTIVE)
			break;
	}

	if (i == EHCI_ITD_NUFRAMES) {
		goto done; /* All 8 descriptors inactive, it's done */
	}

	USBHIST_LOGN(ehcidebug, 10, "ex %p itd %p still active", ex,
	    ex->itdstart, 0, 0);
	return;
done:
	USBHIST_LOG(ehcidebug, "ex %p done", ex, 0, 0, 0);
	callout_stop(&ex->xfer.ux_callout);
	ehci_idone(ex);
}

void
ehci_check_sitd_intr(ehci_softc_t *sc, struct ehci_xfer *ex)
{
	ehci_soft_sitd_t *sitd;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	KASSERT(mutex_owned(&sc->sc_lock));

	if (&ex->xfer != SIMPLEQ_FIRST(&ex->xfer.ux_pipe->up_queue))
		return;

	if (ex->sitdstart == NULL) {
		printf("ehci_check_sitd_intr: not valid sitd\n");
		return;
	}

	sitd = ex->sitdend;
#ifdef DIAGNOSTIC
	if (sitd == NULL) {
		printf("ehci_check_sitd_intr: sitdend == 0\n");
		return;
	}
#endif

	/*
	 * check no active transfers in last sitd, meaning we're finished
	 */

	usb_syncmem(&sitd->dma, sitd->offs + offsetof(ehci_sitd_t, sitd_buffer),
		    sizeof(sitd->sitd.sitd_buffer), BUS_DMASYNC_POSTWRITE |
		    BUS_DMASYNC_POSTREAD);

	if (le32toh(sitd->sitd.sitd_trans) & EHCI_SITD_ACTIVE)
		return;

	USBHIST_LOGN(ehcidebug, 10, "ex=%p done", ex, 0, 0, 0);
	callout_stop(&(ex->xfer.ux_callout));
	ehci_idone(ex);
}


Static void
ehci_idone(struct ehci_xfer *ex)
{
	usbd_xfer_handle xfer = &ex->xfer;
	struct ehci_pipe *epipe = (struct ehci_pipe *)xfer->ux_pipe;
	struct ehci_softc *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	ehci_soft_qtd_t *sqtd, *lsqtd;
	uint32_t status = 0, nstatus = 0;
	int actlen;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	KASSERT(sc->sc_bus.ub_usepolling || mutex_owned(&sc->sc_lock));

	USBHIST_LOG(ehcidebug, "ex=%p", ex, 0, 0, 0);

#ifdef DIAGNOSTIC
	if (ex->isdone) {
		printf("ehci_idone: ex=%p is done!\n", ex);
#ifdef EHCI_DEBUG
		ehci_dump_exfer(ex);
#endif
		return;
	}
	ex->isdone = 1;
#endif

	if (xfer->ux_status == USBD_CANCELLED ||
	    xfer->ux_status == USBD_TIMEOUT) {
		USBHIST_LOG(ehcidebug, "aborted xfer=%p", xfer, 0, 0, 0);
		return;
	}

	USBHIST_LOG(ehcidebug, "xfer=%p, pipe=%p ready", xfer, epipe, 0, 0);
#ifdef EHCI_DEBUG
	ehci_dump_sqtds(ex->sqtdstart);
#endif

	/* The transfer is done, compute actual length and status. */

	u_int xfertype, speed;

	xfertype = UE_GET_XFERTYPE(xfer->ux_pipe->up_endpoint->ue_edesc->bmAttributes);
	speed = xfer->ux_pipe->up_dev->ud_speed;
	if (xfertype == UE_ISOCHRONOUS && speed == USB_SPEED_HIGH) {
		/* HS isoc transfer */

		struct ehci_soft_itd *itd;
		int i, nframes, len, uframes;

		nframes = 0;
		actlen = 0;

		i = xfer->ux_pipe->up_endpoint->ue_edesc->bInterval;
		uframes = min(1 << (i - 1), USB_UFRAMES_PER_FRAME);

		for (itd = ex->itdstart; itd != NULL; itd = itd->xfer_next) {
			usb_syncmem(&itd->dma,itd->offs + offsetof(ehci_itd_t,itd_ctl),
			    sizeof(itd->itd.itd_ctl), BUS_DMASYNC_POSTWRITE |
			    BUS_DMASYNC_POSTREAD);

			for (i = 0; i < EHCI_ITD_NUFRAMES; i += uframes) {
				/* XXX - driver didn't fill in the frame full
				 *   of uframes. This leads to scheduling
				 *   inefficiencies, but working around
				 *   this doubles complexity of tracking
				 *   an xfer.
				 */
				if (nframes >= xfer->ux_nframes)
					break;

				status = le32toh(itd->itd.itd_ctl[i]);
				len = EHCI_ITD_GET_LEN(status);
				if (EHCI_ITD_GET_STATUS(status) != 0)
					len = 0; /*No valid data on error*/

				xfer->ux_frlengths[nframes++] = len;
				actlen += len;
			}

			if (nframes >= xfer->ux_nframes)
				break;
	    	}

		xfer->ux_actlen = actlen;
		xfer->ux_status = USBD_NORMAL_COMPLETION;
		goto end;
	}

	if (xfertype == UE_ISOCHRONOUS && speed == USB_SPEED_FULL) {
		/* FS isoc transfer */
		struct ehci_soft_sitd *sitd;
		int nframes, len;

		nframes = 0;
		actlen = 0;

		for (sitd = ex->sitdstart; sitd != NULL; sitd = sitd->xfer_next) {
			usb_syncmem(&sitd->dma,sitd->offs + offsetof(ehci_sitd_t, sitd_buffer),
			    sizeof(sitd->sitd.sitd_buffer), BUS_DMASYNC_POSTWRITE |
			    BUS_DMASYNC_POSTREAD);

			/* XXX - driver didn't fill in the frame full
			 *   of uframes. This leads to scheduling
			 *   inefficiencies, but working around
			 *   this doubles complexity of tracking
			 *   an xfer.
			 */
			if (nframes >= xfer->ux_nframes)
				break;

			status = le32toh(sitd->sitd.sitd_trans);
			len = EHCI_SITD_GET_LEN(status);
			if (status & (EHCI_SITD_ERR|EHCI_SITD_BUFERR|
			    EHCI_SITD_BABBLE|EHCI_SITD_XACTERR|EHCI_SITD_MISS)) {
				/* No valid data on error */
				len = xfer->ux_frlengths[nframes];
			}

			/*
			 * frlengths[i]: # of bytes to send
			 * len: # of bytes host didn't send
			 */
			xfer->ux_frlengths[nframes] -= len;
			/* frlengths[i]: # of bytes host sent */
			actlen += xfer->ux_frlengths[nframes++];

			if (nframes >= xfer->ux_nframes)
				break;
	    	}

		xfer->ux_actlen = actlen;
		xfer->ux_status = USBD_NORMAL_COMPLETION;
		goto end;
	}

	/* Continue processing xfers using queue heads */

	lsqtd = ex->sqtdend;
	actlen = 0;
	for (sqtd = ex->sqtdstart; sqtd != lsqtd->nextqtd;
	     sqtd = sqtd->nextqtd) {
		usb_syncmem(&sqtd->dma, sqtd->offs, sizeof(sqtd->qtd),
		    BUS_DMASYNC_POSTWRITE | BUS_DMASYNC_POSTREAD);
		nstatus = le32toh(sqtd->qtd.qtd_status);
		if (nstatus & EHCI_QTD_ACTIVE)
			break;

		status = nstatus;
		if (EHCI_QTD_GET_PID(status) != EHCI_QTD_PID_SETUP)
			actlen += sqtd->len - EHCI_QTD_GET_BYTES(status);
	}


	/*
	 * If there are left over TDs we need to update the toggle.
	 * The default pipe doesn't need it since control transfers
	 * start the toggle at 0 every time.
	 * For a short transfer we need to update the toggle for the missing
	 * packets within the qTD.
	 */
	if ((sqtd != lsqtd->nextqtd || EHCI_QTD_GET_BYTES(status)) &&
	    xfer->ux_pipe->up_dev->ud_pipe0 != xfer->ux_pipe) {
		USBHIST_LOG(ehcidebug,
		    "toggle update status=0x%08x nstatus=0x%08x",
		    status, nstatus, 0, 0);
#if 0
		ehci_dump_sqh(epipe->sqh);
		ehci_dump_sqtds(ex->sqtdstart);
#endif
		epipe->nexttoggle = EHCI_QTD_GET_TOGGLE(nstatus);
	}

	USBHIST_LOG(ehcidebug, "len=%d actlen=%d status=0x%08x", xfer->ux_length,
	    actlen, status, 0);
	xfer->ux_actlen = actlen;
	if (status & EHCI_QTD_HALTED) {
#ifdef EHCI_DEBUG
		USBHIST_LOG(ehcidebug, "halted addr=%d endpt=0x%02x",
		   xfer->ux_pipe->up_dev->ud_addr,
		   xfer->ux_pipe->up_endpoint->ue_edesc->bEndpointAddress, 0, 0);
		USBHIST_LOG(ehcidebug, "cerr=%d pid=%d stat=%#x",
		   EHCI_QTD_GET_CERR(status), EHCI_QTD_GET_PID(status),
		   status, 0);
		USBHIST_LOG(ehcidebug,
		    "active =%d halted=%d buferr=%d babble=%d",
		    status & EHCI_QTD_ACTIVE ? 1 : 0,
		    status & EHCI_QTD_HALTED ? 1 : 0,
		    status & EHCI_QTD_BUFERR ? 1 : 0,
		    status & EHCI_QTD_BABBLE ? 1 : 0);

		USBHIST_LOG(ehcidebug,
		    "xacterr=%d missed=%d split =%d ping  =%d",
		    status & EHCI_QTD_XACTERR ? 1 : 0,
		    status & EHCI_QTD_MISSEDMICRO ? 1 : 0,
		    status & EHCI_QTD_SPLITXSTATE ? 1 : 0,
		    status & EHCI_QTD_PINGSTATE ? 1 : 0);

		ehci_dump_sqh(epipe->sqh);
		ehci_dump_sqtds(ex->sqtdstart);
#endif
		/* low&full speed has an extra error flag */
		if (EHCI_QH_GET_EPS(epipe->sqh->qh.qh_endp) !=
		    EHCI_QH_SPEED_HIGH)
			status &= EHCI_QTD_STATERRS | EHCI_QTD_PINGSTATE;
		else
			status &= EHCI_QTD_STATERRS;
		if (status == 0) /* no other errors means a stall */ {
			xfer->ux_status = USBD_STALLED;
		} else {
			xfer->ux_status = USBD_IOERROR; /* more info XXX */
		}
		/* XXX need to reset TT on missed microframe */
		if (status & EHCI_QTD_MISSEDMICRO) {
			printf("%s: missed microframe, TT reset not "
			    "implemented, hub might be inoperational\n",
			    device_xname(sc->sc_dev));
		}
	} else {
		xfer->ux_status = USBD_NORMAL_COMPLETION;
	}

    end:
	/* XXX transfer_complete memcpys out transfer data (for in endpoints)
	 * during this call, before methods->done is called: dma sync required
	 * beforehand? */
	usb_transfer_complete(xfer);
	USBHIST_LOG(ehcidebug, "ex=%p done", ex, 0, 0, 0);
}

/*
 * Wait here until controller claims to have an interrupt.
 * Then call ehci_intr and return.  Use timeout to avoid waiting
 * too long.
 */
Static void
ehci_waitintr(ehci_softc_t *sc, usbd_xfer_handle xfer)
{
	int timo;
	uint32_t intrs;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	xfer->ux_status = USBD_IN_PROGRESS;
	for (timo = xfer->ux_timeout; timo >= 0; timo--) {
		usb_delay_ms(&sc->sc_bus, 1);
		if (sc->sc_dying)
			break;
		intrs = EHCI_STS_INTRS(EOREAD4(sc, EHCI_USBSTS)) &
			sc->sc_eintrs;
		USBHIST_LOG(ehcidebug, "0x%04x", intrs, 0, 0, 0);
#ifdef EHCI_DEBUG
		if (ehcidebug > 15)
			ehci_dump_regs(sc);
#endif
		if (intrs) {
			mutex_spin_enter(&sc->sc_intr_lock);
			ehci_intr1(sc);
			mutex_spin_exit(&sc->sc_intr_lock);
			if (xfer->ux_status != USBD_IN_PROGRESS)
				return;
		}
	}

	/* Timeout */
	USBHIST_LOG(ehcidebug, "timeout", 0, 0, 0, 0);
	xfer->ux_status = USBD_TIMEOUT;
	mutex_enter(&sc->sc_lock);
	usb_transfer_complete(xfer);
	mutex_exit(&sc->sc_lock);
	/* XXX should free TD */
}

Static void
ehci_poll(struct usbd_bus *bus)
{
	ehci_softc_t *sc = bus->ub_hcpriv;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

#ifdef EHCI_DEBUG
	static int last;
	int new;
	new = EHCI_STS_INTRS(EOREAD4(sc, EHCI_USBSTS));
	if (new != last) {
		USBHIST_LOG(ehcidebug, "intrs=0x%04x", new, 0, 0, 0);
		last = new;
	}
#endif

	if (EOREAD4(sc, EHCI_USBSTS) & sc->sc_eintrs) {
		mutex_spin_enter(&sc->sc_intr_lock);
		ehci_intr1(sc);
		mutex_spin_exit(&sc->sc_intr_lock);
	}
}

void
ehci_childdet(device_t self, device_t child)
{
	struct ehci_softc *sc = device_private(self);

	KASSERT(sc->sc_child == child);
	sc->sc_child = NULL;
}

int
ehci_detach(struct ehci_softc *sc, int flags)
{
	int rv = 0;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	if (sc->sc_child != NULL)
		rv = config_detach(sc->sc_child, flags);

	if (rv != 0)
		return (rv);

	callout_halt(&sc->sc_tmo_intrlist, NULL);
	callout_destroy(&sc->sc_tmo_intrlist);

	/* XXX free other data structures XXX */
	if (sc->sc_softitds)
		kmem_free(sc->sc_softitds,
		    sc->sc_flsize * sizeof(ehci_soft_itd_t *));
	cv_destroy(&sc->sc_doorbell);
	cv_destroy(&sc->sc_softwake_cv);

#if 0
	/* XXX destroyed in ehci_pci.c as it controls ehci_intr access */

	softint_disestablish(sc->sc_doorbell_si);
	softint_disestablish(sc->sc_pcd_si);

	mutex_destroy(&sc->sc_lock);
	mutex_destroy(&sc->sc_intr_lock);
#endif

	pool_cache_destroy(sc->sc_xferpool);

	EOWRITE4(sc, EHCI_CONFIGFLAG, 0);

	return (rv);
}


int
ehci_activate(device_t self, enum devact act)
{
	struct ehci_softc *sc = device_private(self);

	switch (act) {
	case DVACT_DEACTIVATE:
		sc->sc_dying = 1;
		return 0;
	default:
		return EOPNOTSUPP;
	}
}

/*
 * Handle suspend/resume.
 *
 * We need to switch to polling mode here, because this routine is
 * called from an interrupt context.  This is all right since we
 * are almost suspended anyway.
 *
 * Note that this power handler isn't to be registered directly; the
 * bus glue needs to call out to it.
 */
bool
ehci_suspend(device_t dv, const pmf_qual_t *qual)
{
	ehci_softc_t *sc = device_private(dv);
	int i;
	uint32_t cmd, hcr;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	mutex_spin_enter(&sc->sc_intr_lock);
	sc->sc_bus.ub_usepolling++;
	mutex_spin_exit(&sc->sc_intr_lock);

	for (i = 1; i <= sc->sc_noport; i++) {
		cmd = EOREAD4(sc, EHCI_PORTSC(i)) & ~EHCI_PS_CLEAR;
		if ((cmd & EHCI_PS_PO) == 0 && (cmd & EHCI_PS_PE) == EHCI_PS_PE)
			EOWRITE4(sc, EHCI_PORTSC(i), cmd | EHCI_PS_SUSP);
	}

	sc->sc_cmd = EOREAD4(sc, EHCI_USBCMD);

	cmd = sc->sc_cmd & ~(EHCI_CMD_ASE | EHCI_CMD_PSE);
	EOWRITE4(sc, EHCI_USBCMD, cmd);

	for (i = 0; i < 100; i++) {
		hcr = EOREAD4(sc, EHCI_USBSTS) & (EHCI_STS_ASS | EHCI_STS_PSS);
		if (hcr == 0)
			break;

		usb_delay_ms(&sc->sc_bus, 1);
	}
	if (hcr != 0)
		printf("%s: reset timeout\n", device_xname(dv));

	cmd &= ~EHCI_CMD_RS;
	EOWRITE4(sc, EHCI_USBCMD, cmd);

	for (i = 0; i < 100; i++) {
		hcr = EOREAD4(sc, EHCI_USBSTS) & EHCI_STS_HCH;
		if (hcr == EHCI_STS_HCH)
			break;

		usb_delay_ms(&sc->sc_bus, 1);
	}
	if (hcr != EHCI_STS_HCH)
		printf("%s: config timeout\n", device_xname(dv));

	mutex_spin_enter(&sc->sc_intr_lock);
	sc->sc_bus.ub_usepolling--;
	mutex_spin_exit(&sc->sc_intr_lock);

	return true;
}

bool
ehci_resume(device_t dv, const pmf_qual_t *qual)
{
	ehci_softc_t *sc = device_private(dv);
	int i;
	uint32_t cmd, hcr;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	/* restore things in case the bios sucks */
	EOWRITE4(sc, EHCI_CTRLDSSEGMENT, 0);
	EOWRITE4(sc, EHCI_PERIODICLISTBASE, DMAADDR(&sc->sc_fldma, 0));
	EOWRITE4(sc, EHCI_ASYNCLISTADDR,
	    sc->sc_async_head->physaddr | EHCI_LINK_QH);

	EOWRITE4(sc, EHCI_USBINTR, sc->sc_eintrs & ~EHCI_INTR_PCIE);

	EOWRITE4(sc, EHCI_USBCMD, sc->sc_cmd);

	hcr = 0;
	for (i = 1; i <= sc->sc_noport; i++) {
		cmd = EOREAD4(sc, EHCI_PORTSC(i)) & ~EHCI_PS_CLEAR;
		if ((cmd & EHCI_PS_PO) == 0 &&
		    (cmd & EHCI_PS_SUSP) == EHCI_PS_SUSP) {
			EOWRITE4(sc, EHCI_PORTSC(i), cmd | EHCI_PS_FPR);
			hcr = 1;
		}
	}

	if (hcr) {
		usb_delay_ms(&sc->sc_bus, USB_RESUME_WAIT);

		for (i = 1; i <= sc->sc_noport; i++) {
			cmd = EOREAD4(sc, EHCI_PORTSC(i)) & ~EHCI_PS_CLEAR;
			if ((cmd & EHCI_PS_PO) == 0 &&
			    (cmd & EHCI_PS_SUSP) == EHCI_PS_SUSP)
				EOWRITE4(sc, EHCI_PORTSC(i),
				    cmd & ~EHCI_PS_FPR);
		}
	}

	EOWRITE4(sc, EHCI_USBCMD, sc->sc_cmd);
	EOWRITE4(sc, EHCI_USBINTR, sc->sc_eintrs);

	for (i = 0; i < 100; i++) {
		hcr = EOREAD4(sc, EHCI_USBSTS) & EHCI_STS_HCH;
		if (hcr != EHCI_STS_HCH)
			break;

		usb_delay_ms(&sc->sc_bus, 1);
	}
	if (hcr == EHCI_STS_HCH)
		printf("%s: config timeout\n", device_xname(dv));

	return true;
}

/*
 * Shut down the controller when the system is going down.
 */
bool
ehci_shutdown(device_t self, int flags)
{
	ehci_softc_t *sc = device_private(self);

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	EOWRITE4(sc, EHCI_USBCMD, 0);	/* Halt controller */
	EOWRITE4(sc, EHCI_USBCMD, EHCI_CMD_HCRESET);
	return true;
}

Static usbd_xfer_handle
ehci_allocx(struct usbd_bus *bus)
{
	struct ehci_softc *sc = bus->ub_hcpriv;
	usbd_xfer_handle xfer;

	xfer = pool_cache_get(sc->sc_xferpool, PR_NOWAIT);
	if (xfer != NULL) {
		memset(xfer, 0, sizeof(struct ehci_xfer));
#ifdef DIAGNOSTIC
		EXFER(xfer)->isdone = 1;
		xfer->ux_state = XFER_BUSY;
#endif
	}
	return (xfer);
}

Static void
ehci_freex(struct usbd_bus *bus, usbd_xfer_handle xfer)
{
	struct ehci_softc *sc = bus->ub_hcpriv;

#ifdef DIAGNOSTIC
	if (xfer->ux_state != XFER_BUSY) {
		printf("ehci_freex: xfer=%p not busy, 0x%08x\n", xfer,
		       xfer->ux_state);
	}
	xfer->ux_state = XFER_FREE;
	if (!EXFER(xfer)->isdone) {
		printf("ehci_freex: !isdone\n");
	}
#endif
	pool_cache_put(sc->sc_xferpool, xfer);
}

Static void
ehci_get_lock(struct usbd_bus *bus, kmutex_t **lock)
{
	struct ehci_softc *sc = bus->ub_hcpriv;

	*lock = &sc->sc_lock;
}

Static void
ehci_device_clear_toggle(usbd_pipe_handle pipe)
{
	struct ehci_pipe *epipe = (struct ehci_pipe *)pipe;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "epipe=%p status=0x%08x",
	    epipe, epipe->sqh->qh.qh_qtd.qtd_status, 0, 0);
#ifdef EHCI_DEBUG
	if (ehcidebug)
		usbd_dump_pipe(pipe);
#endif
	epipe->nexttoggle = 0;
}

Static void
ehci_noop(usbd_pipe_handle pipe)
{
}

#ifdef EHCI_DEBUG
/*
 * Unused function - this is meant to be called from a kernel
 * debugger.
 */
void
ehci_dump(void)
{
	ehci_softc_t *sc = theehci;
	int i;
	printf("cmd=0x%08x, sts=0x%08x, ien=0x%08x\n",
	    EOREAD4(sc, EHCI_USBCMD),
	    EOREAD4(sc, EHCI_USBSTS),
	    EOREAD4(sc, EHCI_USBINTR));
	printf("frindex=0x%08x ctrdsegm=0x%08x periodic=0x%08x async=0x%08x\n",
	    EOREAD4(sc, EHCI_FRINDEX),
	    EOREAD4(sc, EHCI_CTRLDSSEGMENT),
	    EOREAD4(sc, EHCI_PERIODICLISTBASE),
	    EOREAD4(sc, EHCI_ASYNCLISTADDR));
	for (i = 1; i <= sc->sc_noport; i++)
		printf("port %d status=0x%08x\n", i,
		    EOREAD4(sc, EHCI_PORTSC(i)));
}

Static void
ehci_dump_regs(ehci_softc_t *sc)
{
	int i;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug,
	    "cmd     = 0x%08x  sts      = 0x%08x  ien      = 0x%08x",
	    EOREAD4(sc, EHCI_USBCMD), EOREAD4(sc, EHCI_USBSTS),
	    EOREAD4(sc, EHCI_USBINTR), 0);
	USBHIST_LOG(ehcidebug,
	    "frindex = 0x%08x  ctrdsegm = 0x%08x  periodic = 0x%08x  "
	    "async   = 0x%08x",
	    EOREAD4(sc, EHCI_FRINDEX), EOREAD4(sc, EHCI_CTRLDSSEGMENT),
	    EOREAD4(sc, EHCI_PERIODICLISTBASE),
	    EOREAD4(sc, EHCI_ASYNCLISTADDR));
	for (i = 1; i <= sc->sc_noport; i += 2) {
		if (i == sc->sc_noport) {
			USBHIST_LOG(ehcidebug,
			    "port %d status = 0x%08x", i,
			    EOREAD4(sc, EHCI_PORTSC(i)), 0, 0);
		} else {
			USBHIST_LOG(ehcidebug,
			    "port %d status = 0x%08x  port %d status = 0x%08x",
			    i, EOREAD4(sc, EHCI_PORTSC(i)),
			    i+1, EOREAD4(sc, EHCI_PORTSC(i+1)));
		}
	}
}

#ifdef EHCI_DEBUG
#define ehci_dump_link(link, type) do {					\
	USBHIST_LOG(ehcidebug, "    link 0x%08x (T = %d):",		\
	    link,							\
	    link & EHCI_LINK_TERMINATE ? 1 : 0, 0, 0);			\
	if (type) {							\
		USBHIST_LOG(ehcidebug,					\
		    "        ITD  = %d  QH   = %d  SITD = %d  FSTN = %d",\
		    EHCI_LINK_TYPE(link) == EHCI_LINK_ITD ? 1 : 0,	\
		    EHCI_LINK_TYPE(link) == EHCI_LINK_QH ? 1 : 0,	\
		    EHCI_LINK_TYPE(link) == EHCI_LINK_SITD ? 1 : 0,	\
		    EHCI_LINK_TYPE(link) == EHCI_LINK_FSTN ? 1 : 0);	\
	}								\
} while(0)
#else
#define ehci_dump_link(link, type)
#endif

Static void
ehci_dump_sqtds(ehci_soft_qtd_t *sqtd)
{
	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);
	int i;
	uint32_t stop = 0;

	for (i = 0; sqtd && i < 20 && !stop; sqtd = sqtd->nextqtd, i++) {
		ehci_dump_sqtd(sqtd);
		usb_syncmem(&sqtd->dma,
		    sqtd->offs + offsetof(ehci_qtd_t, qtd_next),
		    sizeof(sqtd->qtd),
		    BUS_DMASYNC_POSTWRITE | BUS_DMASYNC_POSTREAD);
		stop = sqtd->qtd.qtd_next & htole32(EHCI_LINK_TERMINATE);
		usb_syncmem(&sqtd->dma,
		    sqtd->offs + offsetof(ehci_qtd_t, qtd_next),
		    sizeof(sqtd->qtd), BUS_DMASYNC_PREREAD);
	}
	if (sqtd)
		USBHIST_LOG(ehcidebug,
		    "dump aborted, too many TDs", 0, 0, 0, 0);
}

Static void
ehci_dump_sqtd(ehci_soft_qtd_t *sqtd)
{
	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	usb_syncmem(&sqtd->dma, sqtd->offs,
	    sizeof(sqtd->qtd), BUS_DMASYNC_POSTWRITE | BUS_DMASYNC_POSTREAD);

	USBHIST_LOGN(ehcidebug, 10,
	    "QTD(%p) at 0x%08x:", sqtd, sqtd->physaddr, 0, 0);
	ehci_dump_qtd(&sqtd->qtd);

	usb_syncmem(&sqtd->dma, sqtd->offs,
	    sizeof(sqtd->qtd), BUS_DMASYNC_PREREAD);
}

Static void
ehci_dump_qtd(ehci_qtd_t *qtd)
{
	USBHIST_FUNC();	USBHIST_CALLED(ehcidebug);

#ifdef USBHIST
	uint32_t s = le32toh(qtd->qtd_status);
#endif

	USBHIST_LOGN(ehcidebug, 10,
	    "     next = 0x%08x  altnext = 0x%08x  status = 0x%08x",
	    qtd->qtd_next, qtd->qtd_altnext, s, 0);
	USBHIST_LOGN(ehcidebug, 10,
	    "   toggle = %d ioc = %d bytes = %#x "
	    "c_page = %#x", EHCI_QTD_GET_TOGGLE(s), EHCI_QTD_GET_IOC(s),
	    EHCI_QTD_GET_BYTES(s), EHCI_QTD_GET_C_PAGE(s));
	USBHIST_LOGN(ehcidebug, 10,
	    "     cerr = %d pid = %d stat  = %x",
	    EHCI_QTD_GET_CERR(s), EHCI_QTD_GET_PID(s), EHCI_QTD_GET_STATUS(s),
	    0);
	USBHIST_LOGN(ehcidebug, 10,
	    "active =%d halted=%d buferr=%d babble=%d",
	    s & EHCI_QTD_ACTIVE ? 1 : 0,
	    s & EHCI_QTD_HALTED ? 1 : 0,
	    s & EHCI_QTD_BUFERR ? 1 : 0,
	    s & EHCI_QTD_BABBLE ? 1 : 0);
	USBHIST_LOGN(ehcidebug, 10,
	    "xacterr=%d missed=%d split =%d ping  =%d",
	    s & EHCI_QTD_XACTERR ? 1 : 0,
	    s & EHCI_QTD_MISSEDMICRO ? 1 : 0,
	    s & EHCI_QTD_SPLITXSTATE ? 1 : 0,
	    s & EHCI_QTD_PINGSTATE ? 1 : 0);
	USBHIST_LOGN(ehcidebug, 10,
	    "buffer[0] = %#x  buffer[1] = %#x  "
	    "buffer[2] = %#x  buffer[3] = %#x",
	    le32toh(qtd->qtd_buffer[0]), le32toh(qtd->qtd_buffer[1]),
	    le32toh(qtd->qtd_buffer[2]), le32toh(qtd->qtd_buffer[3]));
	USBHIST_LOGN(ehcidebug, 10,
	    "buffer[4] = %#x", le32toh(qtd->qtd_buffer[4]), 0, 0, 0);
}

Static void
ehci_dump_sqh(ehci_soft_qh_t *sqh)
{
#ifdef USBHIST
	ehci_qh_t *qh = &sqh->qh;
	ehci_link_t link;
#endif
	uint32_t endp, endphub;
	USBHIST_FUNC();	USBHIST_CALLED(ehcidebug);

	usb_syncmem(&sqh->dma, sqh->offs,
	    sizeof(sqh->qh), BUS_DMASYNC_POSTWRITE | BUS_DMASYNC_POSTREAD);

	USBHIST_LOGN(ehcidebug, 10,
	    "QH(%p) at %#x:", sqh, sqh->physaddr, 0, 0);
	link = le32toh(qh->qh_link);
	ehci_dump_link(link, true);

	endp = le32toh(qh->qh_endp);
	USBHIST_LOGN(ehcidebug, 10,
	    "    endp = %#x", endp, 0, 0, 0);
	USBHIST_LOGN(ehcidebug, 10,
	    "        addr = 0x%02x  inact = %d  endpt = %d  eps = %d",
	    EHCI_QH_GET_ADDR(endp), EHCI_QH_GET_INACT(endp),
	    EHCI_QH_GET_ENDPT(endp),  EHCI_QH_GET_EPS(endp));
	USBHIST_LOGN(ehcidebug, 10,
	    "        dtc  = %d     hrecl = %d",
	    EHCI_QH_GET_DTC(endp), EHCI_QH_GET_HRECL(endp), 0, 0);
	USBHIST_LOGN(ehcidebug, 10,
	    "        ctl  = %d     nrl   = %d  mpl   = %#x(%d)",
	    EHCI_QH_GET_CTL(endp),EHCI_QH_GET_NRL(endp),
	    EHCI_QH_GET_MPL(endp), EHCI_QH_GET_MPL(endp));

	endphub = le32toh(qh->qh_endphub);
	USBHIST_LOGN(ehcidebug, 10,
	    " endphub = %#x", endphub, 0, 0, 0);
	USBHIST_LOGN(ehcidebug, 10,
	    "      smask = 0x%02x  cmask = 0x%02x",
	    EHCI_QH_GET_SMASK(endphub), EHCI_QH_GET_CMASK(endphub), 1, 0);
	USBHIST_LOGN(ehcidebug, 10,
	    "      huba  = 0x%02x  port  = %d  mult = %d",
	    EHCI_QH_GET_HUBA(endphub), EHCI_QH_GET_PORT(endphub),
	    EHCI_QH_GET_MULT(endphub), 0);

	link = le32toh(qh->qh_curqtd);
	ehci_dump_link(link, false);
	USBHIST_LOGN(ehcidebug, 10, "Overlay qTD:", 0, 0, 0, 0);
	ehci_dump_qtd(&qh->qh_qtd);

	usb_syncmem(&sqh->dma, sqh->offs,
	    sizeof(sqh->qh), BUS_DMASYNC_PREREAD);
}

Static void
ehci_dump_itd(struct ehci_soft_itd *itd)
{
	ehci_isoc_trans_t t;
	ehci_isoc_bufr_ptr_t b, b2, b3;
	int i;

	USBHIST_FUNC();	USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "ITD: next phys = %#x", itd->itd.itd_next, 0,
	    0, 0);

	for (i = 0; i < EHCI_ITD_NUFRAMES; i++) {
		t = le32toh(itd->itd.itd_ctl[i]);
		USBHIST_LOG(ehcidebug, "ITDctl %d: stat = %x len = %x",
		    i, EHCI_ITD_GET_STATUS(t), EHCI_ITD_GET_LEN(t), 0);
		USBHIST_LOG(ehcidebug, "     ioc = %x pg = %x offs = %x",
		    EHCI_ITD_GET_IOC(t), EHCI_ITD_GET_PG(t),
		    EHCI_ITD_GET_OFFS(t), 0);
	}
	USBHIST_LOG(ehcidebug, "ITDbufr: ", 0, 0, 0, 0);
	for (i = 0; i < EHCI_ITD_NBUFFERS; i++)
		USBHIST_LOG(ehcidebug, "      %x",
		    EHCI_ITD_GET_BPTR(le32toh(itd->itd.itd_bufr[i])), 0, 0, 0);

	b = le32toh(itd->itd.itd_bufr[0]);
	b2 = le32toh(itd->itd.itd_bufr[1]);
	b3 = le32toh(itd->itd.itd_bufr[2]);
	USBHIST_LOG(ehcidebug, "     ep = %x daddr = %x dir = %d",
	    EHCI_ITD_GET_EP(b), EHCI_ITD_GET_DADDR(b), EHCI_ITD_GET_DIR(b2), 0);
	USBHIST_LOG(ehcidebug, "     maxpkt = %x multi = %x",
	    EHCI_ITD_GET_MAXPKT(b2), EHCI_ITD_GET_MULTI(b3), 0, 0);
}

Static void
ehci_dump_sitd(struct ehci_soft_itd *itd)
{
	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "SITD %p next = %p prev = %p",
	    itd, itd->u.frame_list.next, itd->u.frame_list.prev, 0);
	USBHIST_LOG(ehcidebug, "        xfernext=%p physaddr=%X slot=%d",
	    itd->xfer_next, itd->physaddr, itd->slot, 0);
}

Static void
ehci_dump_exfer(struct ehci_xfer *ex)
{
	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "ex = %p sqtdstart = %p end = %p",
	    ex, ex->sqtdstart, ex->sqtdend, 0);
	USBHIST_LOG(ehcidebug, "     itdstart = %p end = %p isdone = %d",
	    ex->itdstart, ex->itdend, ex->isdone, 0);
}
#endif

Static usbd_status
ehci_open(usbd_pipe_handle pipe)
{
	usbd_device_handle dev = pipe->up_dev;
	ehci_softc_t *sc = dev->ud_bus->ub_hcpriv;
	usb_endpoint_descriptor_t *ed = pipe->up_endpoint->ue_edesc;
	uint8_t addr = dev->ud_addr;
	uint8_t xfertype = UE_GET_XFERTYPE(ed->bmAttributes);
	struct ehci_pipe *epipe = (struct ehci_pipe *)pipe;
	ehci_soft_qh_t *sqh;
	usbd_status err;
	int ival, speed, naks;
	int hshubaddr, hshubport;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "pipe=%p, addr=%d, endpt=%d (%d)",
	    pipe, addr, ed->bEndpointAddress, sc->sc_addr);

	if (dev->ud_myhsport) {
		/*
		 * When directly attached FS/LS device while doing embedded
		 * transaction translations and we are the hub, set the hub
		 * address to 0 (us).
		 */
		if (!(sc->sc_flags & EHCIF_ETTF)
		    || (dev->ud_myhsport->up_parent->ud_addr != sc->sc_addr)) {
			hshubaddr = dev->ud_myhsport->up_parent->ud_addr;
		} else {
			hshubaddr = 0;
		}
		hshubport = dev->ud_myhsport->up_portno;
	} else {
		hshubaddr = 0;
		hshubport = 0;
	}

	if (sc->sc_dying)
		return (USBD_IOERROR);

	/* toggle state needed for bulk endpoints */
	epipe->nexttoggle = pipe->up_endpoint->ue_toggle;

	if (addr == sc->sc_addr) {
		switch (ed->bEndpointAddress) {
		case USB_CONTROL_ENDPOINT:
			pipe->up_methods = &ehci_root_ctrl_methods;
			break;
		case UE_DIR_IN | EHCI_INTR_ENDPT:
			pipe->up_methods = &ehci_root_intr_methods;
			break;
		default:
			USBHIST_LOG(ehcidebug,
			    "bad bEndpointAddress 0x%02x",
			    ed->bEndpointAddress, 0, 0, 0);
			return (USBD_INVAL);
		}
		return (USBD_NORMAL_COMPLETION);
	}

	/* XXX All this stuff is only valid for async. */
	switch (dev->ud_speed) {
	case USB_SPEED_LOW:  speed = EHCI_QH_SPEED_LOW;  break;
	case USB_SPEED_FULL: speed = EHCI_QH_SPEED_FULL; break;
	case USB_SPEED_HIGH: speed = EHCI_QH_SPEED_HIGH; break;
	default: panic("ehci_open: bad device speed %d", dev->ud_speed);
	}
	if (speed == EHCI_QH_SPEED_LOW && xfertype == UE_ISOCHRONOUS) {
		USBHIST_LOG(ehcidebug, "hshubaddr=%d hshubport=%d",
			    hshubaddr, hshubport, 0, 0);
		return USBD_INVAL;
	}

	/*
	 * For interrupt transfer, nak throttling must be disabled, but for
	 * the other transfer type, nak throttling should be enabled from the
	 * viewpoint that avoids the memory thrashing.
	 */
	naks = (xfertype == UE_INTERRUPT) ? 0
	    : ((speed == EHCI_QH_SPEED_HIGH) ? 4 : 0);

	/* Allocate sqh for everything, save isoc xfers */
	if (xfertype != UE_ISOCHRONOUS) {
		sqh = ehci_alloc_sqh(sc);
		if (sqh == NULL)
			return (USBD_NOMEM);
		/* qh_link filled when the QH is added */
		sqh->qh.qh_endp = htole32(
		    EHCI_QH_SET_ADDR(addr) |
		    EHCI_QH_SET_ENDPT(UE_GET_ADDR(ed->bEndpointAddress)) |
		    EHCI_QH_SET_EPS(speed) |
		    EHCI_QH_DTC |
		    EHCI_QH_SET_MPL(UGETW(ed->wMaxPacketSize)) |
		    (speed != EHCI_QH_SPEED_HIGH && xfertype == UE_CONTROL ?
		     EHCI_QH_CTL : 0) |
		    EHCI_QH_SET_NRL(naks)
		    );
		sqh->qh.qh_endphub = htole32(
		    EHCI_QH_SET_MULT(1) |
		    EHCI_QH_SET_SMASK(xfertype == UE_INTERRUPT ? 0x02 : 0)
		    );
		if (speed != EHCI_QH_SPEED_HIGH)
			sqh->qh.qh_endphub |= htole32(
			    EHCI_QH_SET_PORT(hshubport) |
			    EHCI_QH_SET_HUBA(hshubaddr) |
			    EHCI_QH_SET_CMASK(0x08) /* XXX */
			);
		sqh->qh.qh_curqtd = EHCI_NULL;
		/* Fill the overlay qTD */
		sqh->qh.qh_qtd.qtd_next = EHCI_NULL;
		sqh->qh.qh_qtd.qtd_altnext = EHCI_NULL;
		sqh->qh.qh_qtd.qtd_status = htole32(0);

		usb_syncmem(&sqh->dma, sqh->offs, sizeof(sqh->qh),
		    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
		epipe->sqh = sqh;
	} else {
		sqh = NULL;
	} /*xfertype == UE_ISOC*/

	switch (xfertype) {
	case UE_CONTROL:
		err = usb_allocmem(&sc->sc_bus, sizeof(usb_device_request_t),
				   0, &epipe->u.ctl.reqdma);
#ifdef EHCI_DEBUG
		if (err)
			printf("ehci_open: usb_allocmem()=%d\n", err);
#endif
		if (err)
			goto bad;
		pipe->up_methods = &ehci_device_ctrl_methods;
		mutex_enter(&sc->sc_lock);
		ehci_add_qh(sc, sqh, sc->sc_async_head);
		mutex_exit(&sc->sc_lock);
		break;
	case UE_BULK:
		pipe->up_methods = &ehci_device_bulk_methods;
		mutex_enter(&sc->sc_lock);
		ehci_add_qh(sc, sqh, sc->sc_async_head);
		mutex_exit(&sc->sc_lock);
		break;
	case UE_INTERRUPT:
		pipe->up_methods = &ehci_device_intr_methods;
		ival = pipe->up_interval;
		if (ival == USBD_DEFAULT_INTERVAL) {
			if (speed == EHCI_QH_SPEED_HIGH) {
				if (ed->bInterval > 16) {
					/*
					 * illegal with high-speed, but there
					 * were documentation bugs in the spec,
					 * so be generous
					 */
					ival = 256;
				} else
					ival = (1 << (ed->bInterval - 1)) / 8;
			} else
				ival = ed->bInterval;
		}
		err = ehci_device_setintr(sc, sqh, ival);
		if (err)
			goto bad;
		break;
	case UE_ISOCHRONOUS:
		if (speed == EHCI_QH_SPEED_HIGH)
			pipe->up_methods = &ehci_device_isoc_methods;
		else
			pipe->up_methods = &ehci_device_fs_isoc_methods;
		if (ed->bInterval == 0 || ed->bInterval > 16) {
			printf("ehci: opening pipe with invalid bInterval\n");
			err = USBD_INVAL;
			goto bad;
		}
		if (UGETW(ed->wMaxPacketSize) == 0) {
			printf("ehci: zero length endpoint open request\n");
			err = USBD_INVAL;
			goto bad;
		}
		epipe->u.isoc.next_frame = 0;
		epipe->u.isoc.cur_xfers = 0;
		break;
	default:
		USBHIST_LOG(ehcidebug, "bad xfer type %d", xfertype, 0, 0, 0);
		err = USBD_INVAL;
		goto bad;
	}
	return (USBD_NORMAL_COMPLETION);

 bad:
	if (sqh != NULL)
		ehci_free_sqh(sc, sqh);
	return (err);
}

/*
 * Add an ED to the schedule.  Called with USB lock held.
 */
Static void
ehci_add_qh(ehci_softc_t *sc, ehci_soft_qh_t *sqh, ehci_soft_qh_t *head)
{

	KASSERT(mutex_owned(&sc->sc_lock));

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	usb_syncmem(&head->dma, head->offs + offsetof(ehci_qh_t, qh_link),
	    sizeof(head->qh.qh_link), BUS_DMASYNC_POSTWRITE);

	sqh->next = head->next;
	sqh->qh.qh_link = head->qh.qh_link;

	usb_syncmem(&sqh->dma, sqh->offs + offsetof(ehci_qh_t, qh_link),
	    sizeof(sqh->qh.qh_link), BUS_DMASYNC_PREWRITE);

	head->next = sqh;
	head->qh.qh_link = htole32(sqh->physaddr | EHCI_LINK_QH);

	usb_syncmem(&head->dma, head->offs + offsetof(ehci_qh_t, qh_link),
	    sizeof(head->qh.qh_link), BUS_DMASYNC_PREWRITE);

#ifdef EHCI_DEBUG
	ehci_dump_sqh(sqh);
#endif
}

/*
 * Remove an ED from the schedule.  Called with USB lock held.
 */
Static void
ehci_rem_qh(ehci_softc_t *sc, ehci_soft_qh_t *sqh, ehci_soft_qh_t *head)
{
	ehci_soft_qh_t *p;

	KASSERT(mutex_owned(&sc->sc_lock));

	/* XXX */
	for (p = head; p != NULL && p->next != sqh; p = p->next)
		;
	if (p == NULL)
		panic("ehci_rem_qh: ED not found");
	usb_syncmem(&sqh->dma, sqh->offs + offsetof(ehci_qh_t, qh_link),
	    sizeof(sqh->qh.qh_link), BUS_DMASYNC_POSTWRITE);
	p->next = sqh->next;
	p->qh.qh_link = sqh->qh.qh_link;
	usb_syncmem(&p->dma, p->offs + offsetof(ehci_qh_t, qh_link),
	    sizeof(p->qh.qh_link), BUS_DMASYNC_PREWRITE);

	ehci_sync_hc(sc);
}

Static void
ehci_set_qh_qtd(ehci_soft_qh_t *sqh, ehci_soft_qtd_t *sqtd)
{
	int i;
	uint32_t status;

	/* Save toggle bit and ping status. */
	usb_syncmem(&sqh->dma, sqh->offs, sizeof(sqh->qh),
	    BUS_DMASYNC_POSTWRITE | BUS_DMASYNC_POSTREAD);
	status = sqh->qh.qh_qtd.qtd_status &
	    htole32(EHCI_QTD_TOGGLE_MASK |
		    EHCI_QTD_SET_STATUS(EHCI_QTD_PINGSTATE));
	/* Set HALTED to make hw leave it alone. */
	sqh->qh.qh_qtd.qtd_status =
	    htole32(EHCI_QTD_SET_STATUS(EHCI_QTD_HALTED));
	usb_syncmem(&sqh->dma,
	    sqh->offs + offsetof(ehci_qh_t, qh_qtd.qtd_status),
	    sizeof(sqh->qh.qh_qtd.qtd_status),
	    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
	sqh->qh.qh_curqtd = 0;
	sqh->qh.qh_qtd.qtd_next = htole32(sqtd->physaddr);
	sqh->qh.qh_qtd.qtd_altnext = EHCI_NULL;
	for (i = 0; i < EHCI_QTD_NBUFFERS; i++)
		sqh->qh.qh_qtd.qtd_buffer[i] = 0;
	sqh->sqtd = sqtd;
	usb_syncmem(&sqh->dma, sqh->offs, sizeof(sqh->qh),
	    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
	/* Set !HALTED && !ACTIVE to start execution, preserve some fields */
	sqh->qh.qh_qtd.qtd_status = status;
	usb_syncmem(&sqh->dma,
	    sqh->offs + offsetof(ehci_qh_t, qh_qtd.qtd_status),
	    sizeof(sqh->qh.qh_qtd.qtd_status),
	    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
}

/*
 * Ensure that the HC has released all references to the QH.  We do this
 * by asking for a Async Advance Doorbell interrupt and then we wait for
 * the interrupt.
 * To make this easier we first obtain exclusive use of the doorbell.
 */
Static void
ehci_sync_hc(ehci_softc_t *sc)
{
	int error __diagused;

	KASSERT(mutex_owned(&sc->sc_lock));

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	if (sc->sc_dying) {
		USBHIST_LOG(ehcidebug, "dying", 0, 0, 0, 0);
		return;
	}
	/* ask for doorbell */
	EOWRITE4(sc, EHCI_USBCMD, EOREAD4(sc, EHCI_USBCMD) | EHCI_CMD_IAAD);
	USBHIST_LOG(ehcidebug, "cmd = 0x%08x sts = 0x%08x",
		    EOREAD4(sc, EHCI_USBCMD), EOREAD4(sc, EHCI_USBSTS), 0, 0);

	error = cv_timedwait(&sc->sc_doorbell, &sc->sc_lock, hz); /* bell wait */

	USBHIST_LOG(ehcidebug, "cmd = 0x%08x sts = 0x%08x",
		    EOREAD4(sc, EHCI_USBCMD), EOREAD4(sc, EHCI_USBSTS), 0, 0);
#ifdef DIAGNOSTIC
	if (error)
		printf("ehci_sync_hc: cv_timedwait() = %d\n", error);
#endif
}

Static void
ehci_rem_free_itd_chain(ehci_softc_t *sc, struct ehci_xfer *exfer)
{
	struct ehci_soft_itd *itd, *prev;

	prev = NULL;

	if (exfer->itdstart == NULL || exfer->itdend == NULL)
		panic("ehci isoc xfer being freed, but with no itd chain\n");

	for (itd = exfer->itdstart; itd != NULL; itd = itd->xfer_next) {
		prev = itd->u.frame_list.prev;
		/* Unlink itd from hardware chain, or frame array */
		if (prev == NULL) { /* We're at the table head */
			sc->sc_softitds[itd->slot] = itd->u.frame_list.next;
			sc->sc_flist[itd->slot] = itd->itd.itd_next;
			usb_syncmem(&sc->sc_fldma,
			    sizeof(ehci_link_t) * itd->slot,
			    sizeof(ehci_link_t),
			    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);

			if (itd->u.frame_list.next != NULL)
				itd->u.frame_list.next->u.frame_list.prev = NULL;
		} else {
			/* XXX this part is untested... */
			prev->itd.itd_next = itd->itd.itd_next;
			usb_syncmem(&itd->dma,
			    itd->offs + offsetof(ehci_itd_t, itd_next),
			    sizeof(itd->itd.itd_next), BUS_DMASYNC_PREWRITE);

			prev->u.frame_list.next = itd->u.frame_list.next;
			if (itd->u.frame_list.next != NULL)
				itd->u.frame_list.next->u.frame_list.prev = prev;
		}
	}

	prev = NULL;
	for (itd = exfer->itdstart; itd != NULL; itd = itd->xfer_next) {
		if (prev != NULL)
			ehci_free_itd(sc, prev);
		prev = itd;
	}
	if (prev)
		ehci_free_itd(sc, prev);
	exfer->itdstart = NULL;
	exfer->itdend = NULL;
}

Static void
ehci_rem_free_sitd_chain(ehci_softc_t *sc, struct ehci_xfer *exfer)
{
	struct ehci_soft_sitd *sitd, *prev;

	prev = NULL;

	if (exfer->sitdstart == NULL || exfer->sitdend == NULL)
		panic("ehci isoc xfer being freed, but with no sitd chain\n");

	for (sitd = exfer->sitdstart; sitd != NULL; sitd = sitd->xfer_next) {
		prev = sitd->u.frame_list.prev;
		/* Unlink sitd from hardware chain, or frame array */
		if (prev == NULL) { /* We're at the table head */
			sc->sc_softsitds[sitd->slot] = sitd->u.frame_list.next;
			sc->sc_flist[sitd->slot] = sitd->sitd.sitd_next;
			usb_syncmem(&sc->sc_fldma,
			    sizeof(ehci_link_t) * sitd->slot,
			    sizeof(ehci_link_t),
			    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);

			if (sitd->u.frame_list.next != NULL)
				sitd->u.frame_list.next->u.frame_list.prev = NULL;
		} else {
			/* XXX this part is untested... */
			prev->sitd.sitd_next = sitd->sitd.sitd_next;
			usb_syncmem(&sitd->dma,
			    sitd->offs + offsetof(ehci_sitd_t, sitd_next),
			    sizeof(sitd->sitd.sitd_next), BUS_DMASYNC_PREWRITE);

			prev->u.frame_list.next = sitd->u.frame_list.next;
			if (sitd->u.frame_list.next != NULL)
				sitd->u.frame_list.next->u.frame_list.prev = prev;
		}
	}

	prev = NULL;
	for (sitd = exfer->sitdstart; sitd != NULL; sitd = sitd->xfer_next) {
		if (prev != NULL)
			ehci_free_sitd(sc, prev);
		prev = sitd;
	}
	if (prev)
		ehci_free_sitd(sc, prev);
	exfer->sitdstart = NULL;
	exfer->sitdend = NULL;
}


/***********/

/*
 * Data structures and routines to emulate the root hub.
 */
Static usb_device_descriptor_t ehci_devd = {
	.bLength = USB_DEVICE_DESCRIPTOR_SIZE,
	.bDescriptorType = UDESC_DEVICE,
	.bcdUSB = {0x00, 0x02},
	.bDeviceClass = UDCLASS_HUB,
	.bDeviceSubClass = UDSUBCLASS_HUB,
	.bDeviceProtocol = UDPROTO_HSHUBSTT,
	.bMaxPacketSize = 64,
	.idVendor = {0},
	.idProduct = {0},
	.bcdDevice = {0x00,0x01},
	.iManufacturer = 1,
	.iProduct = 2,
	.iSerialNumber = 0,
	.bNumConfigurations = 1
};

Static const usb_device_qualifier_t ehci_odevd = {
	.bLength = USB_DEVICE_DESCRIPTOR_SIZE,
	.bDescriptorType = UDESC_DEVICE_QUALIFIER,
	.bcdUSB = {0x00, 0x02},
	.bDeviceClass = UDCLASS_HUB,
	.bDeviceSubClass = UDSUBCLASS_HUB,
	.bDeviceProtocol = UDPROTO_FSHUB,
	.bMaxPacketSize0 = 64,
	.bNumConfigurations = 1,
	0
};

Static const usb_config_descriptor_t ehci_confd = {
	.bLength = USB_CONFIG_DESCRIPTOR_SIZE,
	.bDescriptorType = UDESC_CONFIG,
	.wTotalLength = USETWD(
		USB_CONFIG_DESCRIPTOR_SIZE +
		USB_INTERFACE_DESCRIPTOR_SIZE +
		USB_ENDPOINT_DESCRIPTOR_SIZE),
	.bNumInterface = 1,
	.bConfigurationValue = 1,
	.iConfiguration = 0,
	.bmAttributes = UC_ATTR_MBO | UC_SELF_POWERED,
	.bMaxPower = 0
};

Static const usb_interface_descriptor_t ehci_ifcd = {
	.bLength = USB_INTERFACE_DESCRIPTOR_SIZE,
	.bDescriptorType = UDESC_INTERFACE,
	.bInterfaceNumber = 0,
	.bAlternateSetting = 0,
	.bNumEndpoints = 1,
	.bInterfaceClass = UICLASS_HUB,
	.bInterfaceSubClass = UISUBCLASS_HUB,
	.bInterfaceProtocol = UIPROTO_HSHUBSTT,
	.iInterface = 0
};

Static const usb_endpoint_descriptor_t ehci_endpd = {
	.bLength = USB_ENDPOINT_DESCRIPTOR_SIZE,
	.bDescriptorType = UDESC_ENDPOINT,
	.bEndpointAddress = UE_DIR_IN | EHCI_INTR_ENDPT,
	.bmAttributes = UE_INTERRUPT,
	.wMaxPacketSize = USETWD(8),
	.bInterval = 12
};

Static const usb_hub_descriptor_t ehci_hubd = {
	.bDescLength = USB_HUB_DESCRIPTOR_SIZE,
	.bDescriptorType = UDESC_HUB,
	.bNbrPorts = 0,
	.wHubCharacteristics = USETWD(0),
	.bPwrOn2PwrGood = 0,
	.bHubContrCurrent = 0,
	.DeviceRemovable = {""},
	.PortPowerCtrlMask = {""},
};

/*
 * Simulate a hardware hub by handling all the necessary requests.
 */
Static usbd_status
ehci_root_ctrl_transfer(usbd_xfer_handle xfer)
{
	ehci_softc_t *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	usbd_status err;

	/* Insert last in queue. */
	mutex_enter(&sc->sc_lock);
	err = usb_insert_transfer(xfer);
	mutex_exit(&sc->sc_lock);
	if (err)
		return (err);

	/* Pipe isn't running, start first */
	return (ehci_root_ctrl_start(SIMPLEQ_FIRST(&xfer->ux_pipe->up_queue)));
}

Static usbd_status
ehci_root_ctrl_start(usbd_xfer_handle xfer)
{
	ehci_softc_t *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	usb_device_request_t *req;
	void *buf = NULL;
	int port, i;
	int len, value, index, l, totlen = 0;
	usb_port_status_t ps;
	usb_hub_descriptor_t hubd;
	usbd_status err;
	uint32_t v;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	if (sc->sc_dying)
		return (USBD_IOERROR);

#ifdef DIAGNOSTIC
	if (!(xfer->ux_rqflags & URQ_REQUEST))
		/* XXX panic */
		return (USBD_INVAL);
#endif
	req = &xfer->ux_request;

	USBHIST_LOG(ehcidebug, "type=0x%02x request=%02x",
		    req->bmRequestType, req->bRequest, 0, 0);

	len = UGETW(req->wLength);
	value = UGETW(req->wValue);
	index = UGETW(req->wIndex);

	if (len != 0)
		buf = xfer->ux_buf;

#define C(x,y) ((x) | ((y) << 8))
	switch(C(req->bRequest, req->bmRequestType)) {
	case C(UR_CLEAR_FEATURE, UT_WRITE_DEVICE):
	case C(UR_CLEAR_FEATURE, UT_WRITE_INTERFACE):
	case C(UR_CLEAR_FEATURE, UT_WRITE_ENDPOINT):
		/*
		 * DEVICE_REMOTE_WAKEUP and ENDPOINT_HALT are no-ops
		 * for the integrated root hub.
		 */
		break;
	case C(UR_GET_CONFIG, UT_READ_DEVICE):
		if (len > 0) {
			*(uint8_t *)buf = sc->sc_conf;
			totlen = 1;
		}
		break;
	case C(UR_GET_DESCRIPTOR, UT_READ_DEVICE):
		USBHIST_LOG(ehcidebug, "wValue=0x%04x", value, 0, 0, 0);
		if (len == 0)
			break;
		switch(value >> 8) {
		case UDESC_DEVICE:
			if ((value & 0xff) != 0) {
				err = USBD_IOERROR;
				goto ret;
			}
			totlen = l = min(len, USB_DEVICE_DESCRIPTOR_SIZE);
			USETW(ehci_devd.idVendor, sc->sc_id_vendor);
			memcpy(buf, &ehci_devd, l);
			break;
		/*
		 * We can't really operate at another speed, but the spec says
		 * we need this descriptor.
		 */
		case UDESC_DEVICE_QUALIFIER:
			if ((value & 0xff) != 0) {
				err = USBD_IOERROR;
				goto ret;
			}
			totlen = l = min(len, USB_DEVICE_DESCRIPTOR_SIZE);
			memcpy(buf, &ehci_odevd, l);
			break;
		/*
		 * We can't really operate at another speed, but the spec says
		 * we need this descriptor.
		 */
		case UDESC_OTHER_SPEED_CONFIGURATION:
		case UDESC_CONFIG:
			if ((value & 0xff) != 0) {
				err = USBD_IOERROR;
				goto ret;
			}
			totlen = l = min(len, USB_CONFIG_DESCRIPTOR_SIZE);
			memcpy(buf, &ehci_confd, l);
			((usb_config_descriptor_t *)buf)->bDescriptorType =
				value >> 8;
			buf = (char *)buf + l;
			len -= l;
			l = min(len, USB_INTERFACE_DESCRIPTOR_SIZE);
			totlen += l;
			memcpy(buf, &ehci_ifcd, l);
			buf = (char *)buf + l;
			len -= l;
			l = min(len, USB_ENDPOINT_DESCRIPTOR_SIZE);
			totlen += l;
			memcpy(buf, &ehci_endpd, l);
			break;
		case UDESC_STRING:
#define sd ((usb_string_descriptor_t *)buf)
			switch (value & 0xff) {
			case 0: /* Language table */
				totlen = usb_makelangtbl(sd, len);
				break;
			case 1: /* Vendor */
				totlen = usb_makestrdesc(sd, len,
							 sc->sc_vendor);
				break;
			case 2: /* Product */
				totlen = usb_makestrdesc(sd, len,
							 "EHCI root hub");
				break;
			}
#undef sd
			break;
		default:
			err = USBD_IOERROR;
			goto ret;
		}
		break;
	case C(UR_GET_INTERFACE, UT_READ_INTERFACE):
		if (len > 0) {
			*(uint8_t *)buf = 0;
			totlen = 1;
		}
		break;
	case C(UR_GET_STATUS, UT_READ_DEVICE):
		if (len > 1) {
			USETW(((usb_status_t *)buf)->wStatus,UDS_SELF_POWERED);
			totlen = 2;
		}
		break;
	case C(UR_GET_STATUS, UT_READ_INTERFACE):
	case C(UR_GET_STATUS, UT_READ_ENDPOINT):
		if (len > 1) {
			USETW(((usb_status_t *)buf)->wStatus, 0);
			totlen = 2;
		}
		break;
	case C(UR_SET_ADDRESS, UT_WRITE_DEVICE):
		if (value >= USB_MAX_DEVICES) {
			err = USBD_IOERROR;
			goto ret;
		}
		sc->sc_addr = value;
		break;
	case C(UR_SET_CONFIG, UT_WRITE_DEVICE):
		if (value != 0 && value != 1) {
			err = USBD_IOERROR;
			goto ret;
		}
		sc->sc_conf = value;
		break;
	case C(UR_SET_DESCRIPTOR, UT_WRITE_DEVICE):
		break;
	case C(UR_SET_FEATURE, UT_WRITE_DEVICE):
	case C(UR_SET_FEATURE, UT_WRITE_INTERFACE):
	case C(UR_SET_FEATURE, UT_WRITE_ENDPOINT):
		err = USBD_IOERROR;
		goto ret;
	case C(UR_SET_INTERFACE, UT_WRITE_INTERFACE):
		break;
	case C(UR_SYNCH_FRAME, UT_WRITE_ENDPOINT):
		break;
	/* Hub requests */
	case C(UR_CLEAR_FEATURE, UT_WRITE_CLASS_DEVICE):
		break;
	case C(UR_CLEAR_FEATURE, UT_WRITE_CLASS_OTHER):
		USBHIST_LOG(ehcidebug,
		    "UR_CLEAR_PORT_FEATURE port=%d feature=%d", index, value,
		    0, 0);
		if (index < 1 || index > sc->sc_noport) {
			err = USBD_IOERROR;
			goto ret;
		}
		port = EHCI_PORTSC(index);
		v = EOREAD4(sc, port);
		USBHIST_LOG(ehcidebug, "portsc=0x%08x", v, 0, 0, 0);
		v &= ~EHCI_PS_CLEAR;
		switch(value) {
		case UHF_PORT_ENABLE:
			EOWRITE4(sc, port, v &~ EHCI_PS_PE);
			break;
		case UHF_PORT_SUSPEND:
			if (!(v & EHCI_PS_SUSP)) /* not suspended */
				break;
			v &= ~EHCI_PS_SUSP;
			EOWRITE4(sc, port, v | EHCI_PS_FPR);
			/* see USB2 spec ch. 7.1.7.7 */
			usb_delay_ms(&sc->sc_bus, 20);
			EOWRITE4(sc, port, v);
			usb_delay_ms(&sc->sc_bus, 2);
#ifdef DEBUG
			v = EOREAD4(sc, port);
			if (v & (EHCI_PS_FPR | EHCI_PS_SUSP))
				printf("ehci: resume failed: %x\n", v);
#endif
			break;
		case UHF_PORT_POWER:
			if (sc->sc_hasppc)
				EOWRITE4(sc, port, v &~ EHCI_PS_PP);
			break;
		case UHF_PORT_TEST:
			USBHIST_LOG(ehcidebug, "clear port test "
				    "%d", index, 0, 0, 0);
			break;
		case UHF_PORT_INDICATOR:
			USBHIST_LOG(ehcidebug, "clear port ind "
				    "%d", index, 0, 0, 0);
			EOWRITE4(sc, port, v &~ EHCI_PS_PIC);
			break;
		case UHF_C_PORT_CONNECTION:
			EOWRITE4(sc, port, v | EHCI_PS_CSC);
			break;
		case UHF_C_PORT_ENABLE:
			EOWRITE4(sc, port, v | EHCI_PS_PEC);
			break;
		case UHF_C_PORT_SUSPEND:
			/* how? */
			break;
		case UHF_C_PORT_OVER_CURRENT:
			EOWRITE4(sc, port, v | EHCI_PS_OCC);
			break;
		case UHF_C_PORT_RESET:
			sc->sc_isreset[index] = 0;
			break;
		default:
			err = USBD_IOERROR;
			goto ret;
		}
#if 0
		switch(value) {
		case UHF_C_PORT_CONNECTION:
		case UHF_C_PORT_ENABLE:
		case UHF_C_PORT_SUSPEND:
		case UHF_C_PORT_OVER_CURRENT:
		case UHF_C_PORT_RESET:
		default:
			break;
		}
#endif
		break;
	case C(UR_GET_DESCRIPTOR, UT_READ_CLASS_DEVICE):
		if (len == 0)
			break;
		if ((value & 0xff) != 0) {
			err = USBD_IOERROR;
			goto ret;
		}
		hubd = ehci_hubd;
		hubd.bNbrPorts = sc->sc_noport;
		v = EOREAD4(sc, EHCI_HCSPARAMS);
		USETW(hubd.wHubCharacteristics,
		    EHCI_HCS_PPC(v) ? UHD_PWR_INDIVIDUAL : UHD_PWR_NO_SWITCH |
		    EHCI_HCS_P_INDICATOR(EREAD4(sc, EHCI_HCSPARAMS))
			? UHD_PORT_IND : 0);
		hubd.bPwrOn2PwrGood = 200; /* XXX can't find out? */
		for (i = 0, l = sc->sc_noport; l > 0; i++, l -= 8, v >>= 8)
			hubd.DeviceRemovable[i++] = 0; /* XXX can't find out? */
		hubd.bDescLength = USB_HUB_DESCRIPTOR_SIZE + i;
		l = min(len, hubd.bDescLength);
		totlen = l;
		memcpy(buf, &hubd, l);
		break;
	case C(UR_GET_STATUS, UT_READ_CLASS_DEVICE):
		if (len != 4) {
			err = USBD_IOERROR;
			goto ret;
		}
		memset(buf, 0, len); /* ? XXX */
		totlen = len;
		break;
	case C(UR_GET_STATUS, UT_READ_CLASS_OTHER):
		USBHIST_LOG(ehcidebug, "get port status i=%d", index, 0, 0, 0);
		if (index < 1 || index > sc->sc_noport) {
			err = USBD_IOERROR;
			goto ret;
		}
		if (len != 4) {
			err = USBD_IOERROR;
			goto ret;
		}
		v = EOREAD4(sc, EHCI_PORTSC(index));
		USBHIST_LOG(ehcidebug, "port status=0x%04x", v, 0, 0, 0);

		i = UPS_HIGH_SPEED;
		if (sc->sc_flags & EHCIF_ETTF) {
			/*
			 * If we are doing embedded transaction translation,
			 * then directly attached LS/FS devices are reset by
			 * the EHCI controller itself.  PSPD is encoded
			 * the same way as in USBSTATUS.
			 */
			i = __SHIFTOUT(v, EHCI_PS_PSPD) * UPS_LOW_SPEED;
		}
		if (v & EHCI_PS_CS)	i |= UPS_CURRENT_CONNECT_STATUS;
		if (v & EHCI_PS_PE)	i |= UPS_PORT_ENABLED;
		if (v & EHCI_PS_SUSP)	i |= UPS_SUSPEND;
		if (v & EHCI_PS_OCA)	i |= UPS_OVERCURRENT_INDICATOR;
		if (v & EHCI_PS_PR)	i |= UPS_RESET;
		if (v & EHCI_PS_PP)	i |= UPS_PORT_POWER;
		if (sc->sc_vendor_port_status)
			i = sc->sc_vendor_port_status(sc, v, i);
		USETW(ps.wPortStatus, i);
		i = 0;
		if (v & EHCI_PS_CSC)	i |= UPS_C_CONNECT_STATUS;
		if (v & EHCI_PS_PEC)	i |= UPS_C_PORT_ENABLED;
		if (v & EHCI_PS_OCC)	i |= UPS_C_OVERCURRENT_INDICATOR;
		if (sc->sc_isreset[index]) i |= UPS_C_PORT_RESET;
		USETW(ps.wPortChange, i);
		l = min(len, sizeof ps);
		memcpy(buf, &ps, l);
		totlen = l;
		break;
	case C(UR_SET_DESCRIPTOR, UT_WRITE_CLASS_DEVICE):
		err = USBD_IOERROR;
		goto ret;
	case C(UR_SET_FEATURE, UT_WRITE_CLASS_DEVICE):
		break;
	case C(UR_SET_FEATURE, UT_WRITE_CLASS_OTHER):
		if (index < 1 || index > sc->sc_noport) {
			err = USBD_IOERROR;
			goto ret;
		}
		port = EHCI_PORTSC(index);
		v = EOREAD4(sc, port);
		USBHIST_LOG(ehcidebug, "portsc=0x%08x", v, 0, 0, 0);
		v &= ~EHCI_PS_CLEAR;
		switch(value) {
		case UHF_PORT_ENABLE:
			EOWRITE4(sc, port, v | EHCI_PS_PE);
			break;
		case UHF_PORT_SUSPEND:
			EOWRITE4(sc, port, v | EHCI_PS_SUSP);
			break;
		case UHF_PORT_RESET:
			USBHIST_LOG(ehcidebug, "reset port %d", index, 0, 0, 0);
			if (EHCI_PS_IS_LOWSPEED(v)
			    && sc->sc_ncomp > 0
			    && !(sc->sc_flags & EHCIF_ETTF)) {
				/*
				 * Low speed device on non-ETTF controller or
				 * unaccompanied controller, give up ownership.
				 */
				ehci_disown(sc, index, 1);
				break;
			}
			/* Start reset sequence. */
			v &= ~ (EHCI_PS_PE | EHCI_PS_PR);
			EOWRITE4(sc, port, v | EHCI_PS_PR);
			/* Wait for reset to complete. */
			usb_delay_ms(&sc->sc_bus, USB_PORT_ROOT_RESET_DELAY);
			if (sc->sc_dying) {
				err = USBD_IOERROR;
				goto ret;
			}
			/*
			 * An embedded transaction translator will automatically
			 * terminate the reset sequence so there's no need to
			 * it.
			 */
			v = EOREAD4(sc, port);
			if (v & EHCI_PS_PR) {
				/* Terminate reset sequence. */
				EOWRITE4(sc, port, v & ~EHCI_PS_PR);
				/* Wait for HC to complete reset. */
				usb_delay_ms(&sc->sc_bus,
				    EHCI_PORT_RESET_COMPLETE);
				if (sc->sc_dying) {
					err = USBD_IOERROR;
					goto ret;
				}
			}

			v = EOREAD4(sc, port);
			USBHIST_LOG(ehcidebug,
			    "ehci after reset, status=0x%08x", v, 0, 0, 0);
			if (v & EHCI_PS_PR) {
				printf("%s: port reset timeout\n",
				       device_xname(sc->sc_dev));
				return (USBD_TIMEOUT);
			}
			if (!(v & EHCI_PS_PE)) {
				/* Not a high speed device, give up ownership.*/
				ehci_disown(sc, index, 0);
				break;
			}
			sc->sc_isreset[index] = 1;
			USBHIST_LOG(ehcidebug,
			    "ehci port %d reset, status = 0x%08x", index, v, 0,
			    0);
			break;
		case UHF_PORT_POWER:
			USBHIST_LOG(ehcidebug,
			    "set port power %d (has PPC = %d)", index,
			    sc->sc_hasppc, 0, 0);
			if (sc->sc_hasppc)
				EOWRITE4(sc, port, v | EHCI_PS_PP);
			break;
		case UHF_PORT_TEST:
			USBHIST_LOG(ehcidebug, "set port test %d",
				index, 0, 0, 0);
			break;
		case UHF_PORT_INDICATOR:
			USBHIST_LOG(ehcidebug, "set port ind %d",
				index, 0, 0, 0);
			EOWRITE4(sc, port, v | EHCI_PS_PIC);
			break;
		default:
			err = USBD_IOERROR;
			goto ret;
		}
		break;
	case C(UR_CLEAR_TT_BUFFER, UT_WRITE_CLASS_OTHER):
	case C(UR_RESET_TT, UT_WRITE_CLASS_OTHER):
	case C(UR_GET_TT_STATE, UT_READ_CLASS_OTHER):
	case C(UR_STOP_TT, UT_WRITE_CLASS_OTHER):
		break;
	default:
		err = USBD_IOERROR;
		goto ret;
	}
	xfer->ux_actlen = totlen;
	err = USBD_NORMAL_COMPLETION;
 ret:
	mutex_enter(&sc->sc_lock);
	xfer->ux_status = err;
	usb_transfer_complete(xfer);
	mutex_exit(&sc->sc_lock);
	return (USBD_IN_PROGRESS);
}

Static void
ehci_disown(ehci_softc_t *sc, int index, int lowspeed)
{
	int port;
	uint32_t v;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "index=%d lowspeed=%d", index, lowspeed, 0, 0);
#ifdef DIAGNOSTIC
	if (sc->sc_npcomp != 0) {
		int i = (index-1) / sc->sc_npcomp;
		if (i >= sc->sc_ncomp)
			printf("%s: strange port\n",
			       device_xname(sc->sc_dev));
		else
			printf("%s: handing over %s speed device on "
			       "port %d to %s\n",
			       device_xname(sc->sc_dev),
			       lowspeed ? "low" : "full",
			       index, device_xname(sc->sc_comps[i]));
	} else {
		printf("%s: npcomp == 0\n", device_xname(sc->sc_dev));
	}
#endif
	port = EHCI_PORTSC(index);
	v = EOREAD4(sc, port) &~ EHCI_PS_CLEAR;
	EOWRITE4(sc, port, v | EHCI_PS_PO);
}

/* Abort a root control request. */
Static void
ehci_root_ctrl_abort(usbd_xfer_handle xfer)
{
	/* Nothing to do, all transfers are synchronous. */
}

/* Close the root pipe. */
Static void
ehci_root_ctrl_close(usbd_pipe_handle pipe)
{
	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);
	/* Nothing to do. */
}

Static void
ehci_root_ctrl_done(usbd_xfer_handle xfer)
{
	xfer->ux_hcpriv = NULL;
}

Static usbd_status
ehci_root_intr_transfer(usbd_xfer_handle xfer)
{
	ehci_softc_t *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	usbd_status err;

	/* Insert last in queue. */
	mutex_enter(&sc->sc_lock);
	err = usb_insert_transfer(xfer);
	mutex_exit(&sc->sc_lock);
	if (err)
		return (err);

	/* Pipe isn't running, start first */
	return (ehci_root_intr_start(SIMPLEQ_FIRST(&xfer->ux_pipe->up_queue)));
}

Static usbd_status
ehci_root_intr_start(usbd_xfer_handle xfer)
{
	usbd_pipe_handle pipe = xfer->ux_pipe;
	ehci_softc_t *sc = pipe->up_dev->ud_bus->ub_hcpriv;

	if (sc->sc_dying)
		return (USBD_IOERROR);

	mutex_enter(&sc->sc_lock);
	sc->sc_intrxfer = xfer;
	mutex_exit(&sc->sc_lock);

	return (USBD_IN_PROGRESS);
}

/* Abort a root interrupt request. */
Static void
ehci_root_intr_abort(usbd_xfer_handle xfer)
{
	ehci_softc_t *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;

	KASSERT(mutex_owned(&sc->sc_lock));
	KASSERT(xfer->ux_pipe->up_intrxfer == xfer);

	sc->sc_intrxfer = NULL;

	xfer->ux_status = USBD_CANCELLED;
	usb_transfer_complete(xfer);
}

/* Close the root pipe. */
Static void
ehci_root_intr_close(usbd_pipe_handle pipe)
{
	ehci_softc_t *sc = pipe->up_dev->ud_bus->ub_hcpriv;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	KASSERT(mutex_owned(&sc->sc_lock));

	sc->sc_intrxfer = NULL;
}

Static void
ehci_root_intr_done(usbd_xfer_handle xfer)
{
	xfer->ux_hcpriv = NULL;
}

/************************/

Static ehci_soft_qh_t *
ehci_alloc_sqh(ehci_softc_t *sc)
{
	ehci_soft_qh_t *sqh;
	usbd_status err;
	int i, offs;
	usb_dma_t dma;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	if (sc->sc_freeqhs == NULL) {
		USBHIST_LOG(ehcidebug, "allocating chunk", 0, 0, 0, 0);
		err = usb_allocmem(&sc->sc_bus, EHCI_SQH_SIZE * EHCI_SQH_CHUNK,
			  EHCI_PAGE_SIZE, &dma);
#ifdef EHCI_DEBUG
		if (err)
			printf("ehci_alloc_sqh: usb_allocmem()=%d\n", err);
#endif
		if (err)
			return (NULL);
		for(i = 0; i < EHCI_SQH_CHUNK; i++) {
			offs = i * EHCI_SQH_SIZE;
			sqh = KERNADDR(&dma, offs);
			sqh->physaddr = DMAADDR(&dma, offs);
			sqh->dma = dma;
			sqh->offs = offs;
			sqh->next = sc->sc_freeqhs;
			sc->sc_freeqhs = sqh;
		}
	}
	sqh = sc->sc_freeqhs;
	sc->sc_freeqhs = sqh->next;
	memset(&sqh->qh, 0, sizeof(ehci_qh_t));
	sqh->next = NULL;
	return (sqh);
}

Static void
ehci_free_sqh(ehci_softc_t *sc, ehci_soft_qh_t *sqh)
{
	sqh->next = sc->sc_freeqhs;
	sc->sc_freeqhs = sqh;
}

Static ehci_soft_qtd_t *
ehci_alloc_sqtd(ehci_softc_t *sc)
{
	ehci_soft_qtd_t *sqtd = NULL;
	usbd_status err;
	int i, offs;
	usb_dma_t dma;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	if (sc->sc_freeqtds == NULL) {
		USBHIST_LOG(ehcidebug, "allocating chunk", 0, 0, 0, 0);

		err = usb_allocmem(&sc->sc_bus, EHCI_SQTD_SIZE*EHCI_SQTD_CHUNK,
			  EHCI_PAGE_SIZE, &dma);
#ifdef EHCI_DEBUG
		if (err)
			printf("ehci_alloc_sqtd: usb_allocmem()=%d\n", err);
#endif
		if (err)
			goto done;

		for(i = 0; i < EHCI_SQTD_CHUNK; i++) {
			offs = i * EHCI_SQTD_SIZE;
			sqtd = KERNADDR(&dma, offs);
			sqtd->physaddr = DMAADDR(&dma, offs);
			sqtd->dma = dma;
			sqtd->offs = offs;

			sqtd->nextqtd = sc->sc_freeqtds;
			sc->sc_freeqtds = sqtd;
		}
	}

	sqtd = sc->sc_freeqtds;
	sc->sc_freeqtds = sqtd->nextqtd;
	memset(&sqtd->qtd, 0, sizeof(ehci_qtd_t));
	sqtd->nextqtd = NULL;
	sqtd->xfer = NULL;

done:
	return (sqtd);
}

Static void
ehci_free_sqtd(ehci_softc_t *sc, ehci_soft_qtd_t *sqtd)
{

	KASSERT(sc->sc_bus.ub_usepolling || mutex_owned(&sc->sc_lock));

	sqtd->nextqtd = sc->sc_freeqtds;
	sc->sc_freeqtds = sqtd;
}

Static usbd_status
ehci_alloc_sqtd_chain(struct ehci_pipe *epipe, ehci_softc_t *sc,
		     int alen, int rd, usbd_xfer_handle xfer,
		     ehci_soft_qtd_t **sp, ehci_soft_qtd_t **ep)
{
	ehci_soft_qtd_t *next, *cur;
	ehci_physaddr_t nextphys;
	uint32_t qtdstatus;
	int len, curlen, mps;
	int i, tog;
	int pages, pageoffs;
	bus_size_t curoffs;
	vaddr_t va, va_offs;
	usb_dma_t *dma = &xfer->ux_dmabuf;
	uint16_t flags = xfer->ux_flags;
	paddr_t a;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "start len=%d", alen, 0, 0, 0);

	len = alen;
	qtdstatus = EHCI_QTD_ACTIVE |
	    EHCI_QTD_SET_PID(rd ? EHCI_QTD_PID_IN : EHCI_QTD_PID_OUT) |
	    EHCI_QTD_SET_CERR(3)
	    /* IOC set below */
	    /* BYTES set below */
	    ;
	mps = UGETW(epipe->pipe.up_endpoint->ue_edesc->wMaxPacketSize);
	tog = epipe->nexttoggle;
	qtdstatus |= EHCI_QTD_SET_TOGGLE(tog);

	cur = ehci_alloc_sqtd(sc);
	*sp = cur;
	if (cur == NULL)
		goto nomem;

	usb_syncmem(dma, 0, alen,
	    rd ? BUS_DMASYNC_PREREAD : BUS_DMASYNC_PREWRITE);
	curoffs = 0;
	for (;;) {
		/* The EHCI hardware can handle at most 5 pages. */
		va_offs = (vaddr_t)KERNADDR(dma, curoffs);
		va_offs = EHCI_PAGE_OFFSET(va_offs);
		if (len-curoffs < EHCI_QTD_NBUFFERS*EHCI_PAGE_SIZE - va_offs) {
			/* we can handle it in this QTD */
			curlen = len - curoffs;
		} else {
			/* must use multiple TDs, fill as much as possible. */
			curlen = EHCI_QTD_NBUFFERS * EHCI_PAGE_SIZE - va_offs;

			/* the length must be a multiple of the max size */
			curlen -= curlen % mps;
			USBHIST_LOG(ehcidebug, "multiple QTDs, "
				    "curlen=%d", curlen, 0, 0, 0);
#ifdef DIAGNOSTIC
			if (curlen == 0)
				panic("ehci_alloc_sqtd_chain: curlen == 0");
#endif
		}
		USBHIST_LOG(ehcidebug, "len=%d curlen=%d curoffs=%zu",
			len, curlen, (size_t)curoffs, 0);

		/*
		 * Allocate another transfer if there's more data left,
		 * or if force last short transfer flag is set and we're
		 * allocating a multiple of the max packet size.
		 */

		if (curoffs + curlen != len ||
		    ((curlen % mps) == 0 && !rd && curlen != 0 &&
		     (flags & USBD_FORCE_SHORT_XFER))) {
			next = ehci_alloc_sqtd(sc);
			if (next == NULL)
				goto nomem;
			nextphys = htole32(next->physaddr);
		} else {
			next = NULL;
			nextphys = EHCI_NULL;
		}

		/* Find number of pages we'll be using, insert dma addresses */
		pages = EHCI_PAGE(curlen + EHCI_PAGE_SIZE -1) >> 12;
		KASSERT(pages <= EHCI_QTD_NBUFFERS);
		pageoffs = EHCI_PAGE(curoffs);
		for (i = 0; i < pages; i++) {
			a = DMAADDR(dma, pageoffs + i * EHCI_PAGE_SIZE);
			cur->qtd.qtd_buffer[i] = htole32(a & 0xFFFFF000);
			/* Cast up to avoid compiler warnings */
			cur->qtd.qtd_buffer_hi[i] = htole32((uint64_t)a >> 32);
		}

		/* First buffer pointer requires a page offset to start at */
		va = (vaddr_t)KERNADDR(dma, curoffs);
		cur->qtd.qtd_buffer[0] |= htole32(EHCI_PAGE_OFFSET(va));

		cur->nextqtd = next;
		cur->qtd.qtd_next = cur->qtd.qtd_altnext = nextphys;
		cur->qtd.qtd_status =
		    htole32(qtdstatus | EHCI_QTD_SET_BYTES(curlen));
		cur->xfer = xfer;
		cur->len = curlen;

		USBHIST_LOG(ehcidebug, "cbp=0x%08zx end=0x%08zx",
		    (size_t)curoffs, (size_t)(curoffs + curlen), 0, 0);

		/* adjust the toggle based on the number of packets in this
		   qtd */
		if (((curlen + mps - 1) / mps) & 1) {
			tog ^= 1;
			qtdstatus ^= EHCI_QTD_TOGGLE_MASK;
		}
		if (next == NULL)
			break;
		usb_syncmem(&cur->dma, cur->offs, sizeof(cur->qtd),
		    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
		USBHIST_LOG(ehcidebug, "extend chain", 0, 0, 0, 0);
		if (len)
			curoffs += curlen;
		cur = next;
	}
	cur->qtd.qtd_status |= htole32(EHCI_QTD_IOC);
	usb_syncmem(&cur->dma, cur->offs, sizeof(cur->qtd),
	    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
	*ep = cur;
	epipe->nexttoggle = tog;

	USBHIST_LOG(ehcidebug, "return sqtd=%p sqtdend=%p",
	    *sp, *ep, 0, 0);

	return (USBD_NORMAL_COMPLETION);

 nomem:
	/* XXX free chain */
	USBHIST_LOG(ehcidebug, "no memory", 0, 0, 0, 0);
	return (USBD_NOMEM);
}

Static void
ehci_free_sqtd_chain(ehci_softc_t *sc, ehci_soft_qtd_t *sqtd,
		    ehci_soft_qtd_t *sqtdend)
{
	ehci_soft_qtd_t *p;
	int i;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "sqtd=%p sqtdend=%p",
	    sqtd, sqtdend, 0, 0);

	for (i = 0; sqtd != sqtdend; sqtd = p, i++) {
		p = sqtd->nextqtd;
		ehci_free_sqtd(sc, sqtd);
	}
}

Static ehci_soft_itd_t *
ehci_alloc_itd(ehci_softc_t *sc)
{
	struct ehci_soft_itd *itd, *freeitd;
	usbd_status err;
	int i, offs, frindex, previndex;
	usb_dma_t dma;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	mutex_enter(&sc->sc_lock);

	/* Find an itd that wasn't freed this frame or last frame. This can
	 * discard itds that were freed before frindex wrapped around
	 * XXX - can this lead to thrashing? Could fix by enabling wrap-around
	 *       interrupt and fiddling with list when that happens */
	frindex = (EOREAD4(sc, EHCI_FRINDEX) + 1) >> 3;
	previndex = (frindex != 0) ? frindex - 1 : sc->sc_flsize;

	freeitd = NULL;
	LIST_FOREACH(itd, &sc->sc_freeitds, u.free_list) {
		if (itd == NULL)
			break;
		if (itd->slot != frindex && itd->slot != previndex) {
			freeitd = itd;
			break;
		}
	}

	if (freeitd == NULL) {
		USBHIST_LOG(ehcidebug, "allocating chunk", 0, 0, 0, 0);
		err = usb_allocmem(&sc->sc_bus, EHCI_ITD_SIZE * EHCI_ITD_CHUNK,
				EHCI_PAGE_SIZE, &dma);

		if (err) {
			USBHIST_LOG(ehcidebug,
			    "alloc returned %d", err, 0, 0, 0);
			mutex_exit(&sc->sc_lock);
			return NULL;
		}

		for (i = 0; i < EHCI_ITD_CHUNK; i++) {
			offs = i * EHCI_ITD_SIZE;
			itd = KERNADDR(&dma, offs);
			itd->physaddr = DMAADDR(&dma, offs);
	 		itd->dma = dma;
			itd->offs = offs;
			LIST_INSERT_HEAD(&sc->sc_freeitds, itd, u.free_list);
		}
		freeitd = LIST_FIRST(&sc->sc_freeitds);
	}

	itd = freeitd;
	LIST_REMOVE(itd, u.free_list);
	memset(&itd->itd, 0, sizeof(ehci_itd_t));
	usb_syncmem(&itd->dma, itd->offs + offsetof(ehci_itd_t, itd_next),
	    sizeof(itd->itd.itd_next),
	    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);

	itd->u.frame_list.next = NULL;
	itd->u.frame_list.prev = NULL;
	itd->xfer_next = NULL;
	itd->slot = 0;

	mutex_exit(&sc->sc_lock);

	return itd;
}

Static ehci_soft_sitd_t *
ehci_alloc_sitd(ehci_softc_t *sc)
{
	struct ehci_soft_sitd *sitd, *freesitd;
	usbd_status err;
	int i, offs, frindex, previndex;
	usb_dma_t dma;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	mutex_enter(&sc->sc_lock);

	/* Find an sitd that wasn't freed this frame or last frame. This can
	 * discard sitds that were freed before frindex wrapped around
	 * XXX - can this lead to thrashing? Could fix by enabling wrap-around
	 *       interrupt and fiddling with list when that happens */
	frindex = (EOREAD4(sc, EHCI_FRINDEX) + 1) >> 3;
	previndex = (frindex != 0) ? frindex - 1 : sc->sc_flsize;

	freesitd = NULL;
	LIST_FOREACH(sitd, &sc->sc_freesitds, u.free_list) {
		if (sitd == NULL)
			break;
		if (sitd->slot != frindex && sitd->slot != previndex) {
			freesitd = sitd;
			break;
		}
	}

	if (freesitd == NULL) {
		USBHIST_LOG(ehcidebug, "allocating chunk", 0, 0, 0, 0);
		err = usb_allocmem(&sc->sc_bus, EHCI_SITD_SIZE * EHCI_SITD_CHUNK,
				EHCI_PAGE_SIZE, &dma);

		if (err) {
			USBHIST_LOG(ehcidebug,
			    "alloc returned %d", err, 0, 0, 0);
			mutex_exit(&sc->sc_lock);
			return NULL;
		}

		for (i = 0; i < EHCI_SITD_CHUNK; i++) {
			offs = i * EHCI_SITD_SIZE;
			sitd = KERNADDR(&dma, offs);
			sitd->physaddr = DMAADDR(&dma, offs);
	 		sitd->dma = dma;
			sitd->offs = offs;
			LIST_INSERT_HEAD(&sc->sc_freesitds, sitd, u.free_list);
		}
		freesitd = LIST_FIRST(&sc->sc_freesitds);
	}

	sitd = freesitd;
	LIST_REMOVE(sitd, u.free_list);
	memset(&sitd->sitd, 0, sizeof(ehci_sitd_t));
	usb_syncmem(&sitd->dma, sitd->offs + offsetof(ehci_sitd_t, sitd_next),
		    sizeof(sitd->sitd.sitd_next), BUS_DMASYNC_PREWRITE |
		    BUS_DMASYNC_PREREAD);

	sitd->u.frame_list.next = NULL;
	sitd->u.frame_list.prev = NULL;
	sitd->xfer_next = NULL;
	sitd->slot = 0;

	mutex_exit(&sc->sc_lock);

	return sitd;
}

Static void
ehci_free_itd(ehci_softc_t *sc, ehci_soft_itd_t *itd)
{

	KASSERT(mutex_owned(&sc->sc_lock));

	LIST_INSERT_HEAD(&sc->sc_freeitds, itd, u.free_list);
}

Static void
ehci_free_sitd(ehci_softc_t *sc, ehci_soft_sitd_t *sitd)
{

	KASSERT(mutex_owned(&sc->sc_lock));

	LIST_INSERT_HEAD(&sc->sc_freesitds, sitd, u.free_list);
}

/****************/

/*
 * Close a reqular pipe.
 * Assumes that there are no pending transactions.
 */
Static void
ehci_close_pipe(usbd_pipe_handle pipe, ehci_soft_qh_t *head)
{
	struct ehci_pipe *epipe = (struct ehci_pipe *)pipe;
	ehci_softc_t *sc = pipe->up_dev->ud_bus->ub_hcpriv;
	ehci_soft_qh_t *sqh = epipe->sqh;

	KASSERT(mutex_owned(&sc->sc_lock));

	ehci_rem_qh(sc, sqh, head);
	ehci_free_sqh(sc, epipe->sqh);
}

/*
 * Abort a device request.
 * If this routine is called at splusb() it guarantees that the request
 * will be removed from the hardware scheduling and that the callback
 * for it will be called with USBD_CANCELLED status.
 * It's impossible to guarantee that the requested transfer will not
 * have happened since the hardware runs concurrently.
 * If the transaction has already happened we rely on the ordinary
 * interrupt processing to process it.
 * XXX This is most probably wrong.
 * XXXMRG this doesn't make sense anymore.
 */
Static void
ehci_abort_xfer(usbd_xfer_handle xfer, usbd_status status)
{
#define exfer EXFER(xfer)
	struct ehci_pipe *epipe = (struct ehci_pipe *)xfer->ux_pipe;
	ehci_softc_t *sc = epipe->pipe.up_dev->ud_bus->ub_hcpriv;
	ehci_soft_qh_t *sqh = epipe->sqh;
	ehci_soft_qtd_t *sqtd;
	ehci_physaddr_t cur;
	uint32_t qhstatus;
	int hit;
	int wake;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "xfer=%p pipe=%p", xfer, epipe, 0, 0);

	KASSERT(mutex_owned(&sc->sc_lock));
	ASSERT_SLEEPABLE();

	if (sc->sc_dying) {
		/* If we're dying, just do the software part. */
		xfer->ux_status = status;	/* make software ignore it */
		callout_stop(&xfer->ux_callout);
		usb_transfer_complete(xfer);
		return;
	}

	/*
	 * If an abort is already in progress then just wait for it to
	 * complete and return.
	 */
	if (xfer->ux_hcflags & UXFER_ABORTING) {
		USBHIST_LOG(ehcidebug, "already aborting", 0, 0, 0, 0);
#ifdef DIAGNOSTIC
		if (status == USBD_TIMEOUT)
			printf("ehci_abort_xfer: TIMEOUT while aborting\n");
#endif
		/* Override the status which might be USBD_TIMEOUT. */
		xfer->ux_status = status;
		USBHIST_LOG(ehcidebug, "waiting for abort to finish",
			0, 0, 0, 0);
		xfer->ux_hcflags |= UXFER_ABORTWAIT;
		while (xfer->ux_hcflags & UXFER_ABORTING)
			cv_wait(&xfer->ux_hccv, &sc->sc_lock);
		return;
	}
	xfer->ux_hcflags |= UXFER_ABORTING;

	/*
	 * Step 1: Make interrupt routine and hardware ignore xfer.
	 */
	xfer->ux_status = status;	/* make software ignore it */
	callout_stop(&xfer->ux_callout);

	usb_syncmem(&sqh->dma,
	    sqh->offs + offsetof(ehci_qh_t, qh_qtd.qtd_status),
	    sizeof(sqh->qh.qh_qtd.qtd_status),
	    BUS_DMASYNC_POSTWRITE | BUS_DMASYNC_POSTREAD);
	qhstatus = sqh->qh.qh_qtd.qtd_status;
	sqh->qh.qh_qtd.qtd_status = qhstatus | htole32(EHCI_QTD_HALTED);
	usb_syncmem(&sqh->dma,
	    sqh->offs + offsetof(ehci_qh_t, qh_qtd.qtd_status),
	    sizeof(sqh->qh.qh_qtd.qtd_status),
	    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
	for (sqtd = exfer->sqtdstart; ; sqtd = sqtd->nextqtd) {
		usb_syncmem(&sqtd->dma,
		    sqtd->offs + offsetof(ehci_qtd_t, qtd_status),
		    sizeof(sqtd->qtd.qtd_status),
		    BUS_DMASYNC_POSTWRITE | BUS_DMASYNC_POSTREAD);
		sqtd->qtd.qtd_status |= htole32(EHCI_QTD_HALTED);
		usb_syncmem(&sqtd->dma,
		    sqtd->offs + offsetof(ehci_qtd_t, qtd_status),
		    sizeof(sqtd->qtd.qtd_status),
		    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
		if (sqtd == exfer->sqtdend)
			break;
	}

	/*
	 * Step 2: Wait until we know hardware has finished any possible
	 * use of the xfer.  Also make sure the soft interrupt routine
	 * has run.
	 */
	ehci_sync_hc(sc);
	sc->sc_softwake = 1;
	usb_schedsoftintr(&sc->sc_bus);
	cv_wait(&sc->sc_softwake_cv, &sc->sc_lock);

	/*
	 * Step 3: Remove any vestiges of the xfer from the hardware.
	 * The complication here is that the hardware may have executed
	 * beyond the xfer we're trying to abort.  So as we're scanning
	 * the TDs of this xfer we check if the hardware points to
	 * any of them.
	 */

	usb_syncmem(&sqh->dma,
	    sqh->offs + offsetof(ehci_qh_t, qh_curqtd),
	    sizeof(sqh->qh.qh_curqtd),
	    BUS_DMASYNC_POSTWRITE | BUS_DMASYNC_POSTREAD);
	cur = EHCI_LINK_ADDR(le32toh(sqh->qh.qh_curqtd));
	hit = 0;
	for (sqtd = exfer->sqtdstart; ; sqtd = sqtd->nextqtd) {
		hit |= cur == sqtd->physaddr;
		if (sqtd == exfer->sqtdend)
			break;
	}
	sqtd = sqtd->nextqtd;
	/* Zap curqtd register if hardware pointed inside the xfer. */
	if (hit && sqtd != NULL) {
		USBHIST_LOG(ehcidebug, "cur=0x%08x", sqtd->physaddr, 0, 0, 0);
		sqh->qh.qh_curqtd = htole32(sqtd->physaddr); /* unlink qTDs */
		usb_syncmem(&sqh->dma,
		    sqh->offs + offsetof(ehci_qh_t, qh_curqtd),
		    sizeof(sqh->qh.qh_curqtd),
		    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
		sqh->qh.qh_qtd.qtd_status = qhstatus;
		usb_syncmem(&sqh->dma,
		    sqh->offs + offsetof(ehci_qh_t, qh_qtd.qtd_status),
		    sizeof(sqh->qh.qh_qtd.qtd_status),
		    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
	} else {
		USBHIST_LOG(ehcidebug, "no hit", 0, 0, 0, 0);
	}

	/*
	 * Step 4: Execute callback.
	 */
#ifdef DIAGNOSTIC
	exfer->isdone = 1;
#endif
	wake = xfer->ux_hcflags & UXFER_ABORTWAIT;
	xfer->ux_hcflags &= ~(UXFER_ABORTING | UXFER_ABORTWAIT);
	usb_transfer_complete(xfer);
	if (wake) {
		cv_broadcast(&xfer->ux_hccv);
	}

	KASSERT(mutex_owned(&sc->sc_lock));
#undef exfer
}

Static void
ehci_abort_isoc_xfer(usbd_xfer_handle xfer, usbd_status status)
{
	ehci_isoc_trans_t trans_status;
	struct ehci_pipe *epipe;
	struct ehci_xfer *exfer;
	ehci_softc_t *sc;
	struct ehci_soft_itd *itd;
	struct ehci_soft_sitd *sitd;
	int i, wake;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	epipe = (struct ehci_pipe *) xfer->ux_pipe;
	exfer = EXFER(xfer);
	sc = epipe->pipe.up_dev->ud_bus->ub_hcpriv;

	USBHIST_LOG(ehcidebug, "xfer %p pipe %p", xfer, epipe, 0, 0);

	KASSERT(mutex_owned(&sc->sc_lock));

	if (sc->sc_dying) {
		xfer->ux_status = status;
		callout_stop(&xfer->ux_callout);
		usb_transfer_complete(xfer);
		return;
	}

	if (xfer->ux_hcflags & UXFER_ABORTING) {
		USBHIST_LOG(ehcidebug, "already aborting", 0, 0, 0, 0);

#ifdef DIAGNOSTIC
		if (status == USBD_TIMEOUT)
			printf("ehci_abort_isoc_xfer: TIMEOUT while aborting\n");
#endif

		xfer->ux_status = status;
		USBHIST_LOG(ehcidebug,
		    "waiting for abort to finish", 0, 0, 0, 0);
		xfer->ux_hcflags |= UXFER_ABORTWAIT;
		while (xfer->ux_hcflags & UXFER_ABORTING)
			cv_wait(&xfer->ux_hccv, &sc->sc_lock);
		goto done;
	}
	xfer->ux_hcflags |= UXFER_ABORTING;

	xfer->ux_status = status;
	callout_stop(&xfer->ux_callout);

	for (itd = exfer->itdstart; itd != NULL; itd = itd->xfer_next) {
		usb_syncmem(&itd->dma,
		    itd->offs + offsetof(ehci_itd_t, itd_ctl),
		    sizeof(itd->itd.itd_ctl),
		    BUS_DMASYNC_POSTWRITE | BUS_DMASYNC_POSTREAD);

		for (i = 0; i < 8; i++) {
			trans_status = le32toh(itd->itd.itd_ctl[i]);
			trans_status &= ~EHCI_ITD_ACTIVE;
			itd->itd.itd_ctl[i] = htole32(trans_status);
		}

		usb_syncmem(&itd->dma,
		    itd->offs + offsetof(ehci_itd_t, itd_ctl),
		    sizeof(itd->itd.itd_ctl),
		    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
	}
	for (sitd = exfer->sitdstart; sitd != NULL; sitd = sitd->xfer_next) {
		usb_syncmem(&sitd->dma,
		    sitd->offs + offsetof(ehci_sitd_t, sitd_buffer),
		    sizeof(sitd->sitd.sitd_buffer),
		    BUS_DMASYNC_POSTWRITE | BUS_DMASYNC_POSTREAD);

		trans_status = le32toh(sitd->sitd.sitd_trans);
		trans_status &= ~EHCI_SITD_ACTIVE;
		sitd->sitd.sitd_trans = htole32(trans_status);

		usb_syncmem(&sitd->dma,
		    sitd->offs + offsetof(ehci_sitd_t, sitd_buffer),
		    sizeof(sitd->sitd.sitd_buffer),
		    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
	}

	sc->sc_softwake = 1;
	usb_schedsoftintr(&sc->sc_bus);
	cv_wait(&sc->sc_softwake_cv, &sc->sc_lock);

#ifdef DIAGNOSTIC
	exfer->isdone = 1;
#endif
	wake = xfer->ux_hcflags & UXFER_ABORTWAIT;
	xfer->ux_hcflags &= ~(UXFER_ABORTING | UXFER_ABORTWAIT);
	usb_transfer_complete(xfer);
	if (wake) {
		cv_broadcast(&xfer->ux_hccv);
	}

done:
	KASSERT(mutex_owned(&sc->sc_lock));
	return;
}

Static void
ehci_timeout(void *addr)
{
	struct ehci_xfer *exfer = addr;
	struct ehci_pipe *epipe = (struct ehci_pipe *)exfer->xfer.ux_pipe;
	ehci_softc_t *sc = epipe->pipe.up_dev->ud_bus->ub_hcpriv;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "exfer %p", exfer, 0, 0, 0);
#ifdef EHCI_DEBUG
	if (ehcidebug > 1)
		usbd_dump_pipe(exfer->xfer.ux_pipe);
#endif

	if (sc->sc_dying) {
		mutex_enter(&sc->sc_lock);
		ehci_abort_xfer(&exfer->xfer, USBD_TIMEOUT);
		mutex_exit(&sc->sc_lock);
		return;
	}

	/* Execute the abort in a process context. */
	usb_init_task(&exfer->abort_task, ehci_timeout_task, addr,
	    USB_TASKQ_MPSAFE);
	usb_add_task(exfer->xfer.ux_pipe->up_dev, &exfer->abort_task,
	    USB_TASKQ_HC);
}

Static void
ehci_timeout_task(void *addr)
{
	usbd_xfer_handle xfer = addr;
	ehci_softc_t *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "xfer=%p", xfer, 0, 0, 0);

	mutex_enter(&sc->sc_lock);
	ehci_abort_xfer(xfer, USBD_TIMEOUT);
	mutex_exit(&sc->sc_lock);
}

/************************/

Static usbd_status
ehci_device_ctrl_transfer(usbd_xfer_handle xfer)
{
	ehci_softc_t *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	usbd_status err;

	/* Insert last in queue. */
	mutex_enter(&sc->sc_lock);
	err = usb_insert_transfer(xfer);
	mutex_exit(&sc->sc_lock);
	if (err)
		return (err);

	/* Pipe isn't running, start first */
	return (ehci_device_ctrl_start(SIMPLEQ_FIRST(&xfer->ux_pipe->up_queue)));
}

Static usbd_status
ehci_device_ctrl_start(usbd_xfer_handle xfer)
{
	ehci_softc_t *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	usbd_status err;

	if (sc->sc_dying)
		return (USBD_IOERROR);

#ifdef DIAGNOSTIC
	if (!(xfer->ux_rqflags & URQ_REQUEST)) {
		/* XXX panic */
		printf("ehci_device_ctrl_transfer: not a request\n");
		return (USBD_INVAL);
	}
#endif

	err = ehci_device_request(xfer);
	if (err) {
		return (err);
	}

	if (sc->sc_bus.ub_usepolling)
		ehci_waitintr(sc, xfer);

	return (USBD_IN_PROGRESS);
}

Static void
ehci_device_ctrl_done(usbd_xfer_handle xfer)
{
	struct ehci_xfer *ex = EXFER(xfer);
	ehci_softc_t *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	struct ehci_pipe *epipe = (struct ehci_pipe *)xfer->ux_pipe;
	usb_device_request_t *req = &xfer->ux_request;
	int len = UGETW(req->wLength);
	int rd = req->bmRequestType & UT_READ;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "xfer=%p", xfer, 0, 0, 0);

	KASSERT(sc->sc_bus.ub_usepolling || mutex_owned(&sc->sc_lock));

#ifdef DIAGNOSTIC
	if (!(xfer->ux_rqflags & URQ_REQUEST)) {
		panic("ehci_ctrl_done: not a request");
	}
#endif

	if (xfer->ux_status != USBD_NOMEM && ehci_active_intr_list(ex)) {
		ehci_del_intr_list(sc, ex);	/* remove from active list */
		ehci_free_sqtd_chain(sc, ex->sqtdstart, NULL);
		usb_syncmem(&epipe->u.ctl.reqdma, 0, sizeof *req,
		    BUS_DMASYNC_POSTWRITE);
		if (len)
			usb_syncmem(&xfer->ux_dmabuf, 0, len,
			    rd ? BUS_DMASYNC_POSTREAD : BUS_DMASYNC_POSTWRITE);
	}

	USBHIST_LOG(ehcidebug, "length=%d", xfer->ux_actlen, 0, 0, 0);
}

/* Abort a device control request. */
Static void
ehci_device_ctrl_abort(usbd_xfer_handle xfer)
{
	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "xfer=%p", xfer, 0, 0, 0);
	ehci_abort_xfer(xfer, USBD_CANCELLED);
}

/* Close a device control pipe. */
Static void
ehci_device_ctrl_close(usbd_pipe_handle pipe)
{
	ehci_softc_t *sc = pipe->up_dev->ud_bus->ub_hcpriv;
	/*struct ehci_pipe *epipe = (struct ehci_pipe *)pipe;*/

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	KASSERT(mutex_owned(&sc->sc_lock));

	USBHIST_LOG(ehcidebug, "pipe=%p", pipe, 0, 0, 0);

	ehci_close_pipe(pipe, sc->sc_async_head);
}

Static usbd_status
ehci_device_request(usbd_xfer_handle xfer)
{
#define exfer EXFER(xfer)
	struct ehci_pipe *epipe = (struct ehci_pipe *)xfer->ux_pipe;
	usb_device_request_t *req = &xfer->ux_request;
	usbd_device_handle dev = epipe->pipe.up_dev;
	ehci_softc_t *sc = dev->ud_bus->ub_hcpriv;
	ehci_soft_qtd_t *setup, *stat, *next;
	ehci_soft_qh_t *sqh;
	int isread;
	int len;
	usbd_status err;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	isread = req->bmRequestType & UT_READ;
	len = UGETW(req->wLength);

	USBHIST_LOG(ehcidebug, "type=0x%02x, request=0x%02x, "
	    "wValue=0x%04x, wIndex=0x%04x",
	    req->bmRequestType, req->bRequest, UGETW(req->wValue),
	    UGETW(req->wIndex));
	USBHIST_LOG(ehcidebug, "len=%d, addr=%d, endpt=%d",
	    len, dev->ud_addr,
	    epipe->pipe.up_endpoint->ue_edesc->bEndpointAddress, 0);

	setup = ehci_alloc_sqtd(sc);
	if (setup == NULL) {
		err = USBD_NOMEM;
		goto bad1;
	}
	stat = ehci_alloc_sqtd(sc);
	if (stat == NULL) {
		err = USBD_NOMEM;
		goto bad2;
	}

	mutex_enter(&sc->sc_lock);

	sqh = epipe->sqh;

	KASSERTMSG(EHCI_QH_GET_ADDR(le32toh(sqh->qh.qh_endp)) == dev->ud_addr,
	    "address QH %d pipe %d\n",
	    EHCI_QH_GET_ADDR(le32toh(sqh->qh.qh_endp)), dev->ud_addr);
	KASSERTMSG(EHCI_QH_GET_MPL(le32toh(sqh->qh.qh_endp)) ==
	    UGETW(epipe->pipe.up_endpoint->ue_edesc->wMaxPacketSize),
	    "MPS QH %d pipe %d\n",
	    EHCI_QH_GET_MPL(le32toh(sqh->qh.qh_endp)),
	    UGETW(epipe->pipe.up_endpoint->ue_edesc->wMaxPacketSize));

	/* Set up data transaction */
	if (len != 0) {
		ehci_soft_qtd_t *end;

		/* Start toggle at 1. */
		epipe->nexttoggle = 1;
		err = ehci_alloc_sqtd_chain(epipe, sc, len, isread, xfer,
			  &next, &end);
		if (err)
			goto bad3;
		end->qtd.qtd_status &= htole32(~EHCI_QTD_IOC);
		end->nextqtd = stat;
		end->qtd.qtd_next = end->qtd.qtd_altnext =
		    htole32(stat->physaddr);
		usb_syncmem(&end->dma, end->offs, sizeof(end->qtd),
		   BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);
	} else {
		next = stat;
	}

	memcpy(KERNADDR(&epipe->u.ctl.reqdma, 0), req, sizeof *req);
	usb_syncmem(&epipe->u.ctl.reqdma, 0, sizeof *req, BUS_DMASYNC_PREWRITE);

	/* Clear toggle */
	setup->qtd.qtd_status = htole32(
	    EHCI_QTD_ACTIVE |
	    EHCI_QTD_SET_PID(EHCI_QTD_PID_SETUP) |
	    EHCI_QTD_SET_CERR(3) |
	    EHCI_QTD_SET_TOGGLE(0) |
	    EHCI_QTD_SET_BYTES(sizeof *req)
	    );
	setup->qtd.qtd_buffer[0] = htole32(DMAADDR(&epipe->u.ctl.reqdma, 0));
	setup->qtd.qtd_buffer_hi[0] = 0;
	setup->nextqtd = next;
	setup->qtd.qtd_next = setup->qtd.qtd_altnext = htole32(next->physaddr);
	setup->xfer = xfer;
	setup->len = sizeof *req;
	usb_syncmem(&setup->dma, setup->offs, sizeof(setup->qtd),
	    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);

	stat->qtd.qtd_status = htole32(
	    EHCI_QTD_ACTIVE |
	    EHCI_QTD_SET_PID(isread ? EHCI_QTD_PID_OUT : EHCI_QTD_PID_IN) |
	    EHCI_QTD_SET_CERR(3) |
	    EHCI_QTD_SET_TOGGLE(1) |
	    EHCI_QTD_IOC
	    );
	stat->qtd.qtd_buffer[0] = 0; /* XXX not needed? */
	stat->qtd.qtd_buffer_hi[0] = 0; /* XXX not needed? */
	stat->nextqtd = NULL;
	stat->qtd.qtd_next = stat->qtd.qtd_altnext = EHCI_NULL;
	stat->xfer = xfer;
	stat->len = 0;
	usb_syncmem(&stat->dma, stat->offs, sizeof(stat->qtd),
	    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);

#ifdef EHCI_DEBUG
	USBHIST_LOGN(ehcidebug, 5, "dump:", 0, 0, 0, 0);
	ehci_dump_sqh(sqh);
	ehci_dump_sqtds(setup);
#endif

	exfer->sqtdstart = setup;
	exfer->sqtdend = stat;
#ifdef DIAGNOSTIC
	if (!exfer->isdone) {
		printf("ehci_device_request: not done, exfer=%p\n", exfer);
	}
	exfer->isdone = 0;
#endif

	/* Insert qTD in QH list. */
	ehci_set_qh_qtd(sqh, setup); /* also does usb_syncmem(sqh) */
	if (xfer->ux_timeout && !sc->sc_bus.ub_usepolling) {
		callout_reset(&xfer->ux_callout, mstohz(xfer->ux_timeout),
		    ehci_timeout, xfer);
	}
	ehci_add_intr_list(sc, exfer);
	xfer->ux_status = USBD_IN_PROGRESS;
	mutex_exit(&sc->sc_lock);

#ifdef EHCI_DEBUG
	USBHIST_LOGN(ehcidebug, 10, "status=%x, dump:",
	    EOREAD4(sc, EHCI_USBSTS), 0, 0, 0);
//	delay(10000);
	ehci_dump_regs(sc);
	ehci_dump_sqh(sc->sc_async_head);
	ehci_dump_sqh(sqh);
	ehci_dump_sqtds(setup);
#endif

	return (USBD_NORMAL_COMPLETION);

 bad3:
	mutex_exit(&sc->sc_lock);
	ehci_free_sqtd(sc, stat);
 bad2:
	ehci_free_sqtd(sc, setup);
 bad1:
	USBHIST_LOG(ehcidebug, "no memory", 0, 0, 0, 0);
	mutex_enter(&sc->sc_lock);
	xfer->ux_status = err;
	usb_transfer_complete(xfer);
	mutex_exit(&sc->sc_lock);
	return (err);
#undef exfer
}

/*
 * Some EHCI chips from VIA seem to trigger interrupts before writing back the
 * qTD status, or miss signalling occasionally under heavy load.  If the host
 * machine is too fast, we we can miss transaction completion - when we scan
 * the active list the transaction still seems to be active.  This generally
 * exhibits itself as a umass stall that never recovers.
 *
 * We work around this behaviour by setting up this callback after any softintr
 * that completes with transactions still pending, giving us another chance to
 * check for completion after the writeback has taken place.
 */
Static void
ehci_intrlist_timeout(void *arg)
{
	ehci_softc_t *sc = arg;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	usb_schedsoftintr(&sc->sc_bus);
}

/************************/

Static usbd_status
ehci_device_bulk_transfer(usbd_xfer_handle xfer)
{
	ehci_softc_t *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	usbd_status err;

	/* Insert last in queue. */
	mutex_enter(&sc->sc_lock);
	err = usb_insert_transfer(xfer);
	mutex_exit(&sc->sc_lock);
	if (err)
		return (err);

	/* Pipe isn't running, start first */
	return (ehci_device_bulk_start(SIMPLEQ_FIRST(&xfer->ux_pipe->up_queue)));
}

Static usbd_status
ehci_device_bulk_start(usbd_xfer_handle xfer)
{
#define exfer EXFER(xfer)
	struct ehci_pipe *epipe = (struct ehci_pipe *)xfer->ux_pipe;
	usbd_device_handle dev = epipe->pipe.up_dev;
	ehci_softc_t *sc = dev->ud_bus->ub_hcpriv;
	ehci_soft_qtd_t *data, *dataend;
	ehci_soft_qh_t *sqh;
	usbd_status err;
	int len, isread, endpt;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "xfer=%p len=%d flags=%d",
	    xfer, xfer->ux_length, xfer->ux_flags, 0);

	if (sc->sc_dying)
		return (USBD_IOERROR);

#ifdef DIAGNOSTIC
	if (xfer->ux_rqflags & URQ_REQUEST)
		panic("ehci_device_bulk_start: a request");
#endif

	mutex_enter(&sc->sc_lock);

	len = xfer->ux_length;
	endpt = epipe->pipe.up_endpoint->ue_edesc->bEndpointAddress;
	isread = UE_GET_DIR(endpt) == UE_DIR_IN;
	sqh = epipe->sqh;

	epipe->u.bulk.length = len;

	err = ehci_alloc_sqtd_chain(epipe, sc, len, isread, xfer, &data,
				   &dataend);
	if (err) {
		USBHIST_LOG(ehcidebug, "no memory", 0, 0, 0, 0);
		xfer->ux_status = err;
		usb_transfer_complete(xfer);
		mutex_exit(&sc->sc_lock);
		return (err);
	}

#ifdef EHCI_DEBUG
	USBHIST_LOGN(ehcidebug, 5, "data(1):", 0, 0, 0, 0);
	ehci_dump_sqh(sqh);
	ehci_dump_sqtds(data);
#endif

	/* Set up interrupt info. */
	exfer->sqtdstart = data;
	exfer->sqtdend = dataend;
#ifdef DIAGNOSTIC
	if (!exfer->isdone) {
		printf("ehci_device_bulk_start: not done, ex=%p\n", exfer);
	}
	exfer->isdone = 0;
#endif

	ehci_set_qh_qtd(sqh, data); /* also does usb_syncmem(sqh) */
	if (xfer->ux_timeout && !sc->sc_bus.ub_usepolling) {
		callout_reset(&xfer->ux_callout, mstohz(xfer->ux_timeout),
		    ehci_timeout, xfer);
	}
	ehci_add_intr_list(sc, exfer);
	xfer->ux_status = USBD_IN_PROGRESS;
	mutex_exit(&sc->sc_lock);

#ifdef EHCI_DEBUG
	USBHIST_LOGN(ehcidebug, 5, "data(2)", 0, 0, 0, 0);
//	delay(10000);
	USBHIST_LOGN(ehcidebug, 5, "data(3)", 0, 0, 0, 0);
	ehci_dump_regs(sc);
#if 0
	printf("async_head:\n");
	ehci_dump_sqh(sc->sc_async_head);
#endif
	USBHIST_LOG(ehcidebug, "sqh:", 0, 0, 0, 0);
	ehci_dump_sqh(sqh);
	ehci_dump_sqtds(data);
#endif

	if (sc->sc_bus.ub_usepolling)
		ehci_waitintr(sc, xfer);

	return (USBD_IN_PROGRESS);
#undef exfer
}

Static void
ehci_device_bulk_abort(usbd_xfer_handle xfer)
{
	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "xfer %p", xfer, 0, 0, 0);
	ehci_abort_xfer(xfer, USBD_CANCELLED);
}

/*
 * Close a device bulk pipe.
 */
Static void
ehci_device_bulk_close(usbd_pipe_handle pipe)
{
	ehci_softc_t *sc = pipe->up_dev->ud_bus->ub_hcpriv;
	struct ehci_pipe *epipe = (struct ehci_pipe *)pipe;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	KASSERT(mutex_owned(&sc->sc_lock));

	USBHIST_LOG(ehcidebug, "pipe=%p", pipe, 0, 0, 0);
	pipe->up_endpoint->ue_toggle = epipe->nexttoggle;
	ehci_close_pipe(pipe, sc->sc_async_head);
}

Static void
ehci_device_bulk_done(usbd_xfer_handle xfer)
{
	struct ehci_xfer *ex = EXFER(xfer);
	ehci_softc_t *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	struct ehci_pipe *epipe = (struct ehci_pipe *)xfer->ux_pipe;
	int endpt = epipe->pipe.up_endpoint->ue_edesc->bEndpointAddress;
	int rd = UE_GET_DIR(endpt) == UE_DIR_IN;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "xfer=%p, actlen=%d",
	    xfer, xfer->ux_actlen, 0, 0);

	KASSERT(mutex_owned(&sc->sc_lock));

	if (xfer->ux_status != USBD_NOMEM && ehci_active_intr_list(ex)) {
		ehci_del_intr_list(sc, ex);	/* remove from active list */
		ehci_free_sqtd_chain(sc, ex->sqtdstart, NULL);
		usb_syncmem(&xfer->ux_dmabuf, 0, xfer->ux_length,
		    rd ? BUS_DMASYNC_POSTREAD : BUS_DMASYNC_POSTWRITE);
	}

	USBHIST_LOG(ehcidebug, "length=%d", xfer->ux_actlen, 0, 0, 0);
}

/************************/

Static usbd_status
ehci_device_setintr(ehci_softc_t *sc, ehci_soft_qh_t *sqh, int ival)
{
	struct ehci_soft_islot *isp;
	int islot, lev;

	/* Find a poll rate that is large enough. */
	for (lev = EHCI_IPOLLRATES - 1; lev > 0; lev--)
		if (EHCI_ILEV_IVAL(lev) <= ival)
			break;

	/* Pick an interrupt slot at the right level. */
	/* XXX could do better than picking at random */
	sc->sc_rand = (sc->sc_rand + 191) % sc->sc_flsize;
	islot = EHCI_IQHIDX(lev, sc->sc_rand);

	sqh->islot = islot;
	isp = &sc->sc_islots[islot];
	mutex_enter(&sc->sc_lock);
	ehci_add_qh(sc, sqh, isp->sqh);
	mutex_exit(&sc->sc_lock);

	return (USBD_NORMAL_COMPLETION);
}

Static usbd_status
ehci_device_intr_transfer(usbd_xfer_handle xfer)
{
	ehci_softc_t *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	usbd_status err;

	/* Insert last in queue. */
	mutex_enter(&sc->sc_lock);
	err = usb_insert_transfer(xfer);
	mutex_exit(&sc->sc_lock);
	if (err)
		return (err);

	/*
	 * Pipe isn't running (otherwise err would be USBD_INPROG),
	 * so start it first.
	 */
	return (ehci_device_intr_start(SIMPLEQ_FIRST(&xfer->ux_pipe->up_queue)));
}

Static usbd_status
ehci_device_intr_start(usbd_xfer_handle xfer)
{
#define exfer EXFER(xfer)
	struct ehci_pipe *epipe = (struct ehci_pipe *)xfer->ux_pipe;
	usbd_device_handle dev = xfer->ux_pipe->up_dev;
	ehci_softc_t *sc = dev->ud_bus->ub_hcpriv;
	ehci_soft_qtd_t *data, *dataend;
	ehci_soft_qh_t *sqh;
	usbd_status err;
	int len, isread, endpt;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "xfer=%p len=%d flags=%d",
	    xfer, xfer->ux_length, xfer->ux_flags, 0);

	if (sc->sc_dying)
		return (USBD_IOERROR);

#ifdef DIAGNOSTIC
	if (xfer->ux_rqflags & URQ_REQUEST)
		panic("ehci_device_intr_start: a request");
#endif

	mutex_enter(&sc->sc_lock);

	len = xfer->ux_length;
	endpt = epipe->pipe.up_endpoint->ue_edesc->bEndpointAddress;
	isread = UE_GET_DIR(endpt) == UE_DIR_IN;
	sqh = epipe->sqh;

	epipe->u.intr.length = len;

	err = ehci_alloc_sqtd_chain(epipe, sc, len, isread, xfer, &data,
	    &dataend);
	if (err) {
		USBHIST_LOG(ehcidebug, "no memory", 0, 0, 0, 0);
		xfer->ux_status = err;
		usb_transfer_complete(xfer);
		mutex_exit(&sc->sc_lock);
		return (err);
	}

#ifdef EHCI_DEBUG
	USBHIST_LOGN(ehcidebug, 5, "data(1)", 0, 0, 0, 0);
	ehci_dump_sqh(sqh);
	ehci_dump_sqtds(data);
#endif

	/* Set up interrupt info. */
	exfer->sqtdstart = data;
	exfer->sqtdend = dataend;
#ifdef DIAGNOSTIC
	if (!exfer->isdone) {
		printf("ehci_device_intr_start: not done, ex=%p\n", exfer);
	}
	exfer->isdone = 0;
#endif

	ehci_set_qh_qtd(sqh, data); /* also does usb_syncmem(sqh) */
	if (xfer->ux_timeout && !sc->sc_bus.ub_usepolling) {
		callout_reset(&xfer->ux_callout, mstohz(xfer->ux_timeout),
		    ehci_timeout, xfer);
	}
	ehci_add_intr_list(sc, exfer);
	xfer->ux_status = USBD_IN_PROGRESS;
	mutex_exit(&sc->sc_lock);

#ifdef EHCI_DEBUG
	USBHIST_LOGN(ehcidebug, 5, "data(2)", 0, 0, 0, 0);
//	delay(10000);
	USBHIST_LOGN(ehcidebug, 5, "data(3)", 0, 0, 0, 0);
	ehci_dump_regs(sc);
	USBHIST_LOGN(ehcidebug, 5, "sqh:", 0, 0, 0, 0);
	ehci_dump_sqh(sqh);
	ehci_dump_sqtds(data);
#endif

	if (sc->sc_bus.ub_usepolling)
		ehci_waitintr(sc, xfer);

	return (USBD_IN_PROGRESS);
#undef exfer
}

Static void
ehci_device_intr_abort(usbd_xfer_handle xfer)
{
	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "xfer=%p", xfer, 0, 0, 0);
	KASSERT(xfer->ux_pipe->up_intrxfer == xfer);

	/*
	 * XXX - abort_xfer uses ehci_sync_hc, which syncs via the advance
	 *       async doorbell. That's dependent on the async list, wheras
	 *       intr xfers are periodic, should not use this?
	 */
	ehci_abort_xfer(xfer, USBD_CANCELLED);
}

Static void
ehci_device_intr_close(usbd_pipe_handle pipe)
{
	ehci_softc_t *sc = pipe->up_dev->ud_bus->ub_hcpriv;
	struct ehci_pipe *epipe = (struct ehci_pipe *)pipe;
	struct ehci_soft_islot *isp;

	KASSERT(mutex_owned(&sc->sc_lock));

	isp = &sc->sc_islots[epipe->sqh->islot];
	ehci_close_pipe(pipe, isp->sqh);
}

Static void
ehci_device_intr_done(usbd_xfer_handle xfer)
{
#define exfer EXFER(xfer)
	struct ehci_xfer *ex = EXFER(xfer);
	ehci_softc_t *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	struct ehci_pipe *epipe = (struct ehci_pipe *)xfer->ux_pipe;
	ehci_soft_qtd_t *data, *dataend;
	ehci_soft_qh_t *sqh;
	usbd_status err;
	int len, isread, endpt;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "xfer=%p, actlen=%d",
	    xfer, xfer->ux_actlen, 0, 0);

	KASSERT(sc->sc_bus.ub_usepolling || mutex_owned(&sc->sc_lock));

	if (xfer->ux_pipe->up_repeat) {
		ehci_free_sqtd_chain(sc, ex->sqtdstart, NULL);

		len = epipe->u.intr.length;
		xfer->ux_length = len;
		endpt = epipe->pipe.up_endpoint->ue_edesc->bEndpointAddress;
		isread = UE_GET_DIR(endpt) == UE_DIR_IN;
		usb_syncmem(&xfer->ux_dmabuf, 0, len,
		    isread ? BUS_DMASYNC_POSTREAD : BUS_DMASYNC_POSTWRITE);
		sqh = epipe->sqh;

		err = ehci_alloc_sqtd_chain(epipe, sc, len, isread, xfer,
		    &data, &dataend);
		if (err) {
			USBHIST_LOG(ehcidebug, "no memory", 0, 0, 0, 0);
			xfer->ux_status = err;
			return;
		}

		/* Set up interrupt info. */
		exfer->sqtdstart = data;
		exfer->sqtdend = dataend;
#ifdef DIAGNOSTIC
		if (!exfer->isdone) {
			USBHIST_LOG(ehcidebug, "marked not done, ex = %p",
				exfer, 0, 0, 0);
			printf("ehci_device_intr_done: not done, ex=%p\n",
			    exfer);
		}
		exfer->isdone = 0;
#endif

		ehci_set_qh_qtd(sqh, data); /* also does usb_syncmem(sqh) */
		if (xfer->ux_timeout && !sc->sc_bus.ub_usepolling) {
			callout_reset(&xfer->ux_callout,
			    mstohz(xfer->ux_timeout), ehci_timeout, xfer);
		}

		xfer->ux_status = USBD_IN_PROGRESS;
	} else if (xfer->ux_status != USBD_NOMEM && ehci_active_intr_list(ex)) {
		ehci_del_intr_list(sc, ex); /* remove from active list */
		ehci_free_sqtd_chain(sc, ex->sqtdstart, NULL);
		endpt = epipe->pipe.up_endpoint->ue_edesc->bEndpointAddress;
		isread = UE_GET_DIR(endpt) == UE_DIR_IN;
		usb_syncmem(&xfer->ux_dmabuf, 0, xfer->ux_length,
		    isread ? BUS_DMASYNC_POSTREAD : BUS_DMASYNC_POSTWRITE);
	}
#undef exfer
}

/************************/

Static usbd_status
ehci_device_fs_isoc_transfer(usbd_xfer_handle xfer)
{
	usbd_status err;

	err = usb_insert_transfer(xfer);
	if (err && err != USBD_IN_PROGRESS)
		return err;

	return ehci_device_fs_isoc_start(xfer);
}

Static usbd_status
ehci_device_fs_isoc_start(usbd_xfer_handle xfer)
{
	struct ehci_pipe *epipe;
	usbd_device_handle dev;
	ehci_softc_t *sc;
	struct ehci_xfer *exfer;
	ehci_soft_sitd_t *sitd, *prev, *start, *stop;
	usb_dma_t *dma_buf;
	int i, j, k, frames;
	int offs, total_length;
	int frindex;
	u_int huba, dir;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	start = NULL;
	prev = NULL;
	sitd = NULL;
	total_length = 0;
	exfer = (struct ehci_xfer *) xfer;
	sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	dev = xfer->ux_pipe->up_dev;
	epipe = (struct ehci_pipe *)xfer->ux_pipe;

	/*
	 * To allow continuous transfers, above we start all transfers
	 * immediately. However, we're still going to get usbd_start_next call
	 * this when another xfer completes. So, check if this is already
	 * in progress or not
	 */

	if (exfer->sitdstart != NULL)
		return USBD_IN_PROGRESS;

	USBHIST_LOG(ehcidebug, "xfer %p len %d flags %d",
	    xfer, xfer->ux_length, xfer->ux_flags, 0);

	if (sc->sc_dying)
		return USBD_IOERROR;

	/*
	 * To avoid complication, don't allow a request right now that'll span
	 * the entire frame table. To within 4 frames, to allow some leeway
	 * on either side of where the hc currently is.
	 */
	if (epipe->pipe.up_endpoint->ue_edesc->bInterval *
			xfer->ux_nframes >= sc->sc_flsize - 4) {
		printf("ehci: isoc descriptor requested that spans the entire"
		    "frametable, too many frames\n");
		return USBD_INVAL;
	}

#ifdef DIAGNOSTIC
	if (xfer->ux_rqflags & URQ_REQUEST)
		panic("ehci_device_fs_isoc_start: request\n");

	if (!exfer->isdone)
		printf("ehci_device_fs_isoc_start: not done, ex = %p\n", exfer);
	exfer->isdone = 0;
#endif

	/*
	 * Step 1: Allocate and initialize sitds.
	 */

	i = epipe->pipe.up_endpoint->ue_edesc->bInterval;
	if (i > 16 || i == 0) {
		/* Spec page 271 says intervals > 16 are invalid */
		USBHIST_LOG(ehcidebug, "bInverval %d invalid\n", 0, 0, 0, 0);

		return USBD_INVAL;
	}

	frames = xfer->ux_nframes;

	if (frames == 0) {
		USBHIST_LOG(ehcidebug, "frames == 0", 0, 0, 0, 0);

		return USBD_INVAL;
	}

	dma_buf = &xfer->ux_dmabuf;
	offs = 0;

	for (i = 0; i < frames; i++) {
		sitd = ehci_alloc_sitd(sc);

		if (prev)
			prev->xfer_next = sitd;
		else
			start = sitd;

#ifdef DIAGNOSTIC
		if (xfer->ux_frlengths[i] > 0x3ff) {
			printf("ehci: invalid frame length\n");
			xfer->ux_frlengths[i] = 0x3ff;
		}
#endif

		sitd->sitd.sitd_trans = htole32(EHCI_SITD_ACTIVE |
		    EHCI_SITD_SET_LEN(xfer->ux_frlengths[i]));

		/* Set page0 index and offset. */
		sitd->sitd.sitd_buffer[0] = htole32(DMAADDR(dma_buf, offs));

		total_length += xfer->ux_frlengths[i];
		offs += xfer->ux_frlengths[i];

		sitd->sitd.sitd_buffer[1] =
		    htole32(EHCI_SITD_SET_BPTR(DMAADDR(dma_buf, offs - 1)));

		huba = dev->ud_myhsport->up_parent->ud_addr;

/*		if (sc->sc_flags & EHCIF_FREESCALE) {
			// Set hub address to 0 if embedded TT is used.
			if (huba == sc->sc_addr)
				huba = 0;
		}
*/

		k = epipe->pipe.up_endpoint->ue_edesc->bEndpointAddress;
		dir = UE_GET_DIR(k) ? 1 : 0;
		sitd->sitd.sitd_endp =
		    htole32(EHCI_SITD_SET_ENDPT(UE_GET_ADDR(k)) |
		    EHCI_SITD_SET_DADDR(dev->ud_addr) |
		    EHCI_SITD_SET_PORT(dev->ud_myhsport->up_portno) |
		    EHCI_SITD_SET_HUBA(huba) |
		    EHCI_SITD_SET_DIR(dir));

		sitd->sitd.sitd_back = htole32(EHCI_LINK_TERMINATE);

		/* XXX */
		u_char sa, sb;
		u_int temp, tlen;
		sa = 0;

		if (dir == 0) {	/* OUT */
			temp = 0;
			tlen = xfer->ux_frlengths[i];
			if (tlen <= 188) {
				temp |= 1;	/* T-count = 1, TP = ALL */
				tlen = 1;
			} else {
				tlen += 187;
				tlen /= 188;
				temp |= tlen;	/* T-count = [1..6] */
				temp |= 8;	/* TP = Begin */
			}
			sitd->sitd.sitd_buffer[1] |= htole32(temp);

			tlen += sa;

			if (tlen >= 8) {
				sb = 0;
			} else {
				sb = (1 << tlen);
			}

			sa = (1 << sa);
			sa = (sb - sa) & 0x3F;
			sb = 0;
		} else {
			sb = (-(4 << sa)) & 0xFE;
			sa = (1 << sa) & 0x3F;
			sa = 0x01;
			sb = 0xfc;
		}

		sitd->sitd.sitd_sched = htole32(EHCI_SITD_SET_SMASK(sa) |
		    EHCI_SITD_SET_CMASK(sb));

		prev = sitd;
	} /* End of frame */

	sitd->sitd.sitd_trans |= htole32(EHCI_SITD_IOC);

	stop = sitd;
	stop->xfer_next = NULL;
	exfer->isoc_len = total_length;

	usb_syncmem(&exfer->xfer.ux_dmabuf, 0, total_length,
		BUS_DMASYNC_PREREAD | BUS_DMASYNC_PREWRITE);

	/*
	 * Part 2: Transfer descriptors have now been set up, now they must
	 * be scheduled into the periodic frame list. Erk. Not wanting to
	 * complicate matters, transfer is denied if the transfer spans
	 * more than the period frame list.
	 */

	mutex_enter(&sc->sc_lock);

	/* Start inserting frames */
	if (epipe->u.isoc.cur_xfers > 0) {
		frindex = epipe->u.isoc.next_frame;
	} else {
		frindex = EOREAD4(sc, EHCI_FRINDEX);
		frindex = frindex >> 3; /* Erase microframe index */
		frindex += 2;
	}

	if (frindex >= sc->sc_flsize)
		frindex &= (sc->sc_flsize - 1);

	/* Whats the frame interval? */
	i = epipe->pipe.up_endpoint->ue_edesc->bInterval;

	sitd = start;
	for (j = 0; j < frames; j++) {
		if (sitd == NULL)
			panic("ehci: unexpectedly ran out of isoc sitds\n");

		sitd->sitd.sitd_next = sc->sc_flist[frindex];
		if (sitd->sitd.sitd_next == 0)
			/* FIXME: frindex table gets initialized to NULL
			 * or EHCI_NULL? */
			sitd->sitd.sitd_next = EHCI_NULL;

		usb_syncmem(&sitd->dma,
		    sitd->offs + offsetof(ehci_sitd_t, sitd_next),
		    sizeof(ehci_sitd_t),
		    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);

		sc->sc_flist[frindex] =
		    htole32(EHCI_LINK_SITD | sitd->physaddr);

		usb_syncmem(&sc->sc_fldma,
		    sizeof(ehci_link_t) * frindex,
		    sizeof(ehci_link_t),
		    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);

		sitd->u.frame_list.next = sc->sc_softsitds[frindex];
		sc->sc_softsitds[frindex] = sitd;
		if (sitd->u.frame_list.next != NULL)
			sitd->u.frame_list.next->u.frame_list.prev = sitd;
		sitd->slot = frindex;
		sitd->u.frame_list.prev = NULL;

		frindex += i;
		if (frindex >= sc->sc_flsize)
			frindex -= sc->sc_flsize;

		sitd = sitd->xfer_next;
	}

	epipe->u.isoc.cur_xfers++;
	epipe->u.isoc.next_frame = frindex;

	exfer->sitdstart = start;
	exfer->sitdend = stop;
	exfer->sqtdstart = NULL;
	exfer->sqtdstart = NULL;

	ehci_add_intr_list(sc, exfer);
	xfer->ux_status = USBD_IN_PROGRESS;
	xfer->ux_done = 0;

	mutex_exit(&sc->sc_lock);

	if (sc->sc_bus.ub_usepolling) {
		printf("Starting ehci isoc xfer with polling. Bad idea?\n");
		ehci_waitintr(sc, xfer);
	}

	return USBD_IN_PROGRESS;
}

Static void
ehci_device_fs_isoc_abort(usbd_xfer_handle xfer)
{
	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "xfer = %p", xfer, 0, 0, 0);
	ehci_abort_isoc_xfer(xfer, USBD_CANCELLED);
}

Static void
ehci_device_fs_isoc_close(usbd_pipe_handle pipe)
{
	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "nothing in the pipe to free?", 0, 0, 0, 0);
}

Static void
ehci_device_fs_isoc_done(usbd_xfer_handle xfer)
{
	struct ehci_xfer *exfer;
	ehci_softc_t *sc;
	struct ehci_pipe *epipe;

	exfer = EXFER(xfer);
	sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	epipe = (struct ehci_pipe *) xfer->ux_pipe;

	KASSERT(mutex_owned(&sc->sc_lock));

	epipe->u.isoc.cur_xfers--;
	if (xfer->ux_status != USBD_NOMEM && ehci_active_intr_list(exfer)) {
		ehci_del_intr_list(sc, exfer);
		ehci_rem_free_sitd_chain(sc, exfer);
	}

	usb_syncmem(&xfer->ux_dmabuf, 0, xfer->ux_length, BUS_DMASYNC_POSTWRITE |
		    BUS_DMASYNC_POSTREAD);
}
Static usbd_status
ehci_device_isoc_transfer(usbd_xfer_handle xfer)
{
	ehci_softc_t *sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	usbd_status err;

	mutex_enter(&sc->sc_lock);
	err = usb_insert_transfer(xfer);
	mutex_exit(&sc->sc_lock);
	if (err && err != USBD_IN_PROGRESS)
		return err;

	return ehci_device_isoc_start(xfer);
}

Static usbd_status
ehci_device_isoc_start(usbd_xfer_handle xfer)
{
	struct ehci_pipe *epipe;
	ehci_softc_t *sc;
	struct ehci_xfer *exfer;
	ehci_soft_itd_t *itd, *prev, *start, *stop;
	usb_dma_t *dma_buf;
	int i, j, k, frames, uframes, ufrperframe;
	int trans_count, offs, total_length;
	int frindex;

	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	start = NULL;
	prev = NULL;
	itd = NULL;
	trans_count = 0;
	total_length = 0;
	exfer = (struct ehci_xfer *) xfer;
	sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	epipe = (struct ehci_pipe *)xfer->ux_pipe;

	/*
	 * To allow continuous transfers, above we start all transfers
	 * immediately. However, we're still going to get usbd_start_next call
	 * this when another xfer completes. So, check if this is already
	 * in progress or not
	 */

	if (exfer->itdstart != NULL)
		return USBD_IN_PROGRESS;

	USBHIST_LOG(ehcidebug, "xfer %p len %d flags %d",
	    xfer, xfer->ux_length, xfer->ux_flags, 0);

	if (sc->sc_dying)
		return USBD_IOERROR;

	/*
	 * To avoid complication, don't allow a request right now that'll span
	 * the entire frame table. To within 4 frames, to allow some leeway
	 * on either side of where the hc currently is.
	 */
	if ((1 << (epipe->pipe.up_endpoint->ue_edesc->bInterval)) *
			xfer->ux_nframes >= (sc->sc_flsize - 4) * 8) {
		USBHIST_LOG(ehcidebug,
		    "isoc descriptor spans entire frametable", 0, 0, 0, 0);
		printf("ehci: isoc descriptor requested that spans the entire frametable, too many frames\n");
		return USBD_INVAL;
	}

#ifdef DIAGNOSTIC
	if (xfer->ux_rqflags & URQ_REQUEST)
		panic("ehci_device_isoc_start: request\n");

	if (!exfer->isdone) {
		USBHIST_LOG(ehcidebug, "marked not done, ex = %p", exfer,
			0, 0, 0);
		printf("ehci_device_isoc_start: not done, ex = %p\n", exfer);
	}
	exfer->isdone = 0;
#endif

	/*
	 * Step 1: Allocate and initialize itds, how many do we need?
	 * One per transfer if interval >= 8 microframes, fewer if we use
	 * multiple microframes per frame.
	 */

	i = epipe->pipe.up_endpoint->ue_edesc->bInterval;
	if (i > 16 || i == 0) {
		/* Spec page 271 says intervals > 16 are invalid */
		USBHIST_LOG(ehcidebug, "bInvertal %d invalid", i, 0, 0, 0);
		return USBD_INVAL;
	}

	ufrperframe = max(1, USB_UFRAMES_PER_FRAME / (1 << (i - 1)));
	frames = (xfer->ux_nframes + (ufrperframe - 1)) / ufrperframe;
	uframes = USB_UFRAMES_PER_FRAME / ufrperframe;

	if (frames == 0) {
		USBHIST_LOG(ehcidebug, "frames == 0", 0, 0, 0, 0);
		return USBD_INVAL;
	}

	dma_buf = &xfer->ux_dmabuf;
	offs = 0;

	for (i = 0; i < frames; i++) {
		int froffs = offs;
		itd = ehci_alloc_itd(sc);

		if (prev != NULL) {
			prev->itd.itd_next =
			    htole32(itd->physaddr | EHCI_LINK_ITD);
			usb_syncmem(&itd->dma,
			    itd->offs + offsetof(ehci_itd_t, itd_next),
			    sizeof(itd->itd.itd_next), BUS_DMASYNC_POSTWRITE);

			prev->xfer_next = itd;
	    	} else {
			start = itd;
		}

		/*
		 * Step 1.5, initialize uframes
		 */
		for (j = 0; j < EHCI_ITD_NUFRAMES; j += uframes) {
			/* Calculate which page in the list this starts in */
			int addr = DMAADDR(dma_buf, froffs);
			addr = EHCI_PAGE_OFFSET(addr);
			addr += (offs - froffs);
			addr = EHCI_PAGE(addr);
			addr /= EHCI_PAGE_SIZE;

			/* This gets the initial offset into the first page,
			 * looks how far further along the current uframe
			 * offset is. Works out how many pages that is.
			 */

			itd->itd.itd_ctl[j] = htole32 ( EHCI_ITD_ACTIVE |
			    EHCI_ITD_SET_LEN(xfer->ux_frlengths[trans_count]) |
			    EHCI_ITD_SET_PG(addr) |
			    EHCI_ITD_SET_OFFS(EHCI_PAGE_OFFSET(DMAADDR(dma_buf,offs))));

			total_length += xfer->ux_frlengths[trans_count];
			offs += xfer->ux_frlengths[trans_count];
			trans_count++;

			if (trans_count >= xfer->ux_nframes) { /*Set IOC*/
				itd->itd.itd_ctl[j] |= htole32(EHCI_ITD_IOC);
				break;
			}
		}

		/* Step 1.75, set buffer pointers. To simplify matters, all
		 * pointers are filled out for the next 7 hardware pages in
		 * the dma block, so no need to worry what pages to cover
		 * and what to not.
		 */

		for (j = 0; j < EHCI_ITD_NBUFFERS; j++) {
			/*
			 * Don't try to lookup a page that's past the end
			 * of buffer
			 */
			int page_offs = EHCI_PAGE(froffs + (EHCI_PAGE_SIZE * j));
			if (page_offs >= dma_buf->udma_block->size)
				break;

			unsigned long long page = DMAADDR(dma_buf, page_offs);
			page = EHCI_PAGE(page);
			itd->itd.itd_bufr[j] =
			    htole32(EHCI_ITD_SET_BPTR(page));
			itd->itd.itd_bufr_hi[j] =
			    htole32(page >> 32);
		}

		/*
		 * Other special values
		 */

		k = epipe->pipe.up_endpoint->ue_edesc->bEndpointAddress;
		itd->itd.itd_bufr[0] |= htole32(EHCI_ITD_SET_EP(UE_GET_ADDR(k)) |
		    EHCI_ITD_SET_DADDR(epipe->pipe.up_dev->ud_addr));

		k = (UE_GET_DIR(epipe->pipe.up_endpoint->ue_edesc->bEndpointAddress))
		    ? 1 : 0;
		j = UGETW(epipe->pipe.up_endpoint->ue_edesc->wMaxPacketSize);
		itd->itd.itd_bufr[1] |= htole32(EHCI_ITD_SET_DIR(k) |
		    EHCI_ITD_SET_MAXPKT(UE_GET_SIZE(j)));

		/* FIXME: handle invalid trans */
		itd->itd.itd_bufr[2] |=
		    htole32(EHCI_ITD_SET_MULTI(UE_GET_TRANS(j)+1));

		usb_syncmem(&itd->dma,
		    itd->offs + offsetof(ehci_itd_t, itd_next),
		    sizeof(ehci_itd_t),
		    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);

		prev = itd;
	} /* End of frame */

	stop = itd;
	stop->xfer_next = NULL;
	exfer->isoc_len = total_length;

	usb_syncmem(&exfer->xfer.ux_dmabuf, 0, total_length,
		BUS_DMASYNC_PREREAD | BUS_DMASYNC_PREWRITE);

	/*
	 * Part 2: Transfer descriptors have now been set up, now they must
	 * be scheduled into the period frame list. Erk. Not wanting to
	 * complicate matters, transfer is denied if the transfer spans
	 * more than the period frame list.
	 */

	mutex_enter(&sc->sc_lock);

	/* Start inserting frames */
	if (epipe->u.isoc.cur_xfers > 0) {
		frindex = epipe->u.isoc.next_frame;
	} else {
		frindex = EOREAD4(sc, EHCI_FRINDEX);
		frindex = frindex >> 3; /* Erase microframe index */
		frindex += 2;
	}

	if (frindex >= sc->sc_flsize)
		frindex &= (sc->sc_flsize - 1);

	/* What's the frame interval? */
	i = (1 << (epipe->pipe.up_endpoint->ue_edesc->bInterval - 1));
	if (i / USB_UFRAMES_PER_FRAME == 0)
		i = 1;
	else
		i /= USB_UFRAMES_PER_FRAME;

	itd = start;
	for (j = 0; j < frames; j++) {
		if (itd == NULL)
			panic("ehci: unexpectedly ran out of isoc itds, isoc_start\n");

		itd->itd.itd_next = sc->sc_flist[frindex];
		if (itd->itd.itd_next == 0)
			/* FIXME: frindex table gets initialized to NULL
			 * or EHCI_NULL? */
			itd->itd.itd_next = EHCI_NULL;

		usb_syncmem(&itd->dma,
		    itd->offs + offsetof(ehci_itd_t, itd_next),
		    sizeof(itd->itd.itd_next),
		    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);

		sc->sc_flist[frindex] = htole32(EHCI_LINK_ITD | itd->physaddr);

		usb_syncmem(&sc->sc_fldma,
		    sizeof(ehci_link_t) * frindex,
		    sizeof(ehci_link_t),
		    BUS_DMASYNC_PREWRITE | BUS_DMASYNC_PREREAD);

		itd->u.frame_list.next = sc->sc_softitds[frindex];
		sc->sc_softitds[frindex] = itd;
		if (itd->u.frame_list.next != NULL)
			itd->u.frame_list.next->u.frame_list.prev = itd;
		itd->slot = frindex;
		itd->u.frame_list.prev = NULL;

		frindex += i;
		if (frindex >= sc->sc_flsize)
			frindex -= sc->sc_flsize;

		itd = itd->xfer_next;
	}

	epipe->u.isoc.cur_xfers++;
	epipe->u.isoc.next_frame = frindex;

	exfer->itdstart = start;
	exfer->itdend = stop;
	exfer->sqtdstart = NULL;
	exfer->sqtdend = NULL;

	ehci_add_intr_list(sc, exfer);
	xfer->ux_status = USBD_IN_PROGRESS;
	xfer->ux_done = 0;
	mutex_exit(&sc->sc_lock);

	if (sc->sc_bus.ub_usepolling) {
		printf("Starting ehci isoc xfer with polling. Bad idea?\n");
		ehci_waitintr(sc, xfer);
	}

	return USBD_IN_PROGRESS;
}

Static void
ehci_device_isoc_abort(usbd_xfer_handle xfer)
{
	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "xfer = %p", xfer, 0, 0, 0);
	ehci_abort_isoc_xfer(xfer, USBD_CANCELLED);
}

Static void
ehci_device_isoc_close(usbd_pipe_handle pipe)
{
	USBHIST_FUNC(); USBHIST_CALLED(ehcidebug);

	USBHIST_LOG(ehcidebug, "nothing in the pipe to free?", 0, 0, 0, 0);
}

Static void
ehci_device_isoc_done(usbd_xfer_handle xfer)
{
	struct ehci_xfer *exfer;
	ehci_softc_t *sc;
	struct ehci_pipe *epipe;

	exfer = EXFER(xfer);
	sc = xfer->ux_pipe->up_dev->ud_bus->ub_hcpriv;
	epipe = (struct ehci_pipe *) xfer->ux_pipe;

	KASSERT(mutex_owned(&sc->sc_lock));

	epipe->u.isoc.cur_xfers--;
	if (xfer->ux_status != USBD_NOMEM && ehci_active_intr_list(exfer)) {
		ehci_del_intr_list(sc, exfer);
		ehci_rem_free_itd_chain(sc, exfer);
	}

	usb_syncmem(&xfer->ux_dmabuf, 0, xfer->ux_length, BUS_DMASYNC_POSTWRITE |
	    BUS_DMASYNC_POSTREAD);

}