if_aue.c revision 1.36
1 /* $NetBSD: if_aue.c,v 1.36 2000/03/30 00:18:17 augustss Exp $ */ 2 /* 3 * Copyright (c) 1997, 1998, 1999, 2000 4 * Bill Paul <wpaul (at) ee.columbia.edu>. All rights reserved. 5 * 6 * Redistribution and use in source and binary forms, with or without 7 * modification, are permitted provided that the following conditions 8 * are met: 9 * 1. Redistributions of source code must retain the above copyright 10 * notice, this list of conditions and the following disclaimer. 11 * 2. Redistributions in binary form must reproduce the above copyright 12 * notice, this list of conditions and the following disclaimer in the 13 * documentation and/or other materials provided with the distribution. 14 * 3. All advertising materials mentioning features or use of this software 15 * must display the following acknowledgement: 16 * This product includes software developed by Bill Paul. 17 * 4. Neither the name of the author nor the names of any co-contributors 18 * may be used to endorse or promote products derived from this software 19 * without specific prior written permission. 20 * 21 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND 22 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 23 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 24 * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD 25 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 26 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 27 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 28 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 29 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 30 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 31 * THE POSSIBILITY OF SUCH DAMAGE. 32 * 33 * $FreeBSD: src/sys/dev/usb/if_aue.c,v 1.11 2000/01/14 01:36:14 wpaul Exp $ 34 */ 35 36 /* 37 * ADMtek AN986 Pegasus USB to ethernet driver. Datasheet is available 38 * from http://www.admtek.com.tw. 39 * 40 * Written by Bill Paul <wpaul (at) ee.columbia.edu> 41 * Electrical Engineering Department 42 * Columbia University, New York City 43 */ 44 45 /* 46 * The Pegasus chip uses four USB "endpoints" to provide 10/100 ethernet 47 * support: the control endpoint for reading/writing registers, burst 48 * read endpoint for packet reception, burst write for packet transmission 49 * and one for "interrupts." The chip uses the same RX filter scheme 50 * as the other ADMtek ethernet parts: one perfect filter entry for the 51 * the station address and a 64-bit multicast hash table. The chip supports 52 * both MII and HomePNA attachments. 53 * 54 * Since the maximum data transfer speed of USB is supposed to be 12Mbps, 55 * you're never really going to get 100Mbps speeds from this device. I 56 * think the idea is to allow the device to connect to 10 or 100Mbps 57 * networks, not necessarily to provide 100Mbps performance. Also, since 58 * the controller uses an external PHY chip, it's possible that board 59 * designers might simply choose a 10Mbps PHY. 60 * 61 * Registers are accessed using usbd_do_request(). Packet transfers are 62 * done using usbd_transfer() and friends. 63 */ 64 65 /* 66 * Ported to NetBSD and somewhat rewritten by Lennart Augustsson. 67 */ 68 69 /* 70 * TODO: 71 * better error messages from rxstat 72 * split out if_auevar.h 73 * add thread to avoid register reads from interrupt context 74 * more error checks 75 * investigate short rx problem 76 * proper cleanup on errors 77 */ 78 79 #if defined(__NetBSD__) 80 #include "opt_inet.h" 81 #include "opt_ns.h" 82 #include "bpfilter.h" 83 #include "rnd.h" 84 #elif defined(__OpenBSD__) 85 #include "bpfilter.h" 86 #endif /* defined(__OpenBSD__) */ 87 88 #include <sys/param.h> 89 #include <sys/systm.h> 90 #include <sys/sockio.h> 91 #include <sys/mbuf.h> 92 #include <sys/malloc.h> 93 #include <sys/kernel.h> 94 #include <sys/socket.h> 95 96 #if defined(__FreeBSD__) 97 98 #include <net/ethernet.h> 99 #include <machine/clock.h> /* for DELAY */ 100 #include <sys/bus.h> 101 /* "controller miibus0" required. See GENERIC if you get errors here. */ 102 #include "miibus_if.h" 103 104 #elif defined(__NetBSD__) || defined(__OpenBSD__) 105 106 #include <sys/device.h> 107 #if NRND > 0 108 #include <sys/rnd.h> 109 #endif 110 111 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 112 113 #include <net/if.h> 114 #if defined(__NetBSD__) || defined(__FreeBSD__) 115 #include <net/if_arp.h> 116 #endif 117 #include <net/if_dl.h> 118 #include <net/if_media.h> 119 120 #if defined(__NetBSD__) || defined(__OpenBSD__) 121 #define BPF_MTAP(ifp, m) bpf_mtap((ifp)->if_bpf, (m)) 122 #else 123 #define BPF_MTAP(ifp, m) bpf_mtap((ifp), (m)) 124 #endif 125 126 #if defined(__FreeBSD__) || NBPFILTER > 0 127 #include <net/bpf.h> 128 #endif 129 130 #if defined(__NetBSD__) 131 #include <net/if_ether.h> 132 #ifdef INET 133 #include <netinet/in.h> 134 #include <netinet/if_inarp.h> 135 #endif 136 #endif /* defined(__NetBSD__) */ 137 138 #if defined(__OpenBSD__) 139 #ifdef INET 140 #include <netinet/in.h> 141 #include <netinet/in_systm.h> 142 #include <netinet/in_var.h> 143 #include <netinet/ip.h> 144 #include <netinet/if_ether.h> 145 #endif 146 #endif /* defined(__OpenBSD__) */ 147 148 #if defined(__NetBSD__) || defined(__OpenBSD__) 149 #ifdef NS 150 #include <netns/ns.h> 151 #include <netns/ns_if.h> 152 #endif 153 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 154 155 #include <dev/mii/mii.h> 156 #include <dev/mii/miivar.h> 157 158 #include <dev/usb/usb.h> 159 #include <dev/usb/usbdi.h> 160 #include <dev/usb/usbdi_util.h> 161 #include <dev/usb/usbdevs.h> 162 163 #ifdef __FreeBSD__ 164 #include <dev/usb/usb_ethersubr.h> 165 #endif 166 167 #include <dev/usb/if_auereg.h> 168 169 #ifdef AUE_DEBUG 170 #define DPRINTF(x) if (auedebug) logprintf x 171 #define DPRINTFN(n,x) if (auedebug >= (n)) logprintf x 172 int auedebug = 0; 173 #else 174 #define DPRINTF(x) 175 #define DPRINTFN(n,x) 176 #endif 177 178 /* 179 * Various supported device vendors/products. 180 */ 181 Static struct aue_type aue_devs[] = { 182 { USB_VENDOR_BILLIONTON, USB_PRODUCT_BILLIONTON_USB100 }, 183 { USB_VENDOR_MELCO, USB_PRODUCT_MELCO_LUATX }, 184 { USB_VENDOR_LINKSYS, USB_PRODUCT_LINKSYS_USB100TX }, 185 { USB_VENDOR_ADMTEK, USB_PRODUCT_ADMTEK_PEGASUS }, 186 { USB_VENDOR_DLINK, USB_PRODUCT_DLINK_DSB650TX }, 187 { USB_VENDOR_DLINK, USB_PRODUCT_DLINK_DSB650TX_PNA }, 188 { USB_VENDOR_SMC, USB_PRODUCT_SMC_2202USB }, 189 { USB_VENDOR_COREGA, USB_PRODUCT_COREGA_FETHER_USB_TX }, 190 { USB_VENDOR_IODATA, USB_PRODUCT_IODATA_USBETTX }, 191 { 0, 0 } 192 }; 193 194 USB_DECLARE_DRIVER(aue); 195 196 Static int aue_tx_list_init __P((struct aue_softc *)); 197 Static int aue_rx_list_init __P((struct aue_softc *)); 198 Static int aue_newbuf __P((struct aue_softc *, struct aue_chain *, 199 struct mbuf *)); 200 Static int aue_send __P((struct aue_softc *, struct mbuf *, int)); 201 Static void aue_intr __P((usbd_xfer_handle, 202 usbd_private_handle, usbd_status)); 203 Static void aue_rxeof __P((usbd_xfer_handle, 204 usbd_private_handle, usbd_status)); 205 Static void aue_txeof __P((usbd_xfer_handle, 206 usbd_private_handle, usbd_status)); 207 Static void aue_tick __P((void *)); 208 Static void aue_start __P((struct ifnet *)); 209 Static int aue_ioctl __P((struct ifnet *, u_long, caddr_t)); 210 Static void aue_init __P((void *)); 211 Static void aue_stop __P((struct aue_softc *)); 212 Static void aue_watchdog __P((struct ifnet *)); 213 #ifdef __FreeBSD__ 214 Static void aue_shutdown __P((device_ptr_t)); 215 #endif 216 Static int aue_openpipes __P((struct aue_softc *)); 217 Static int aue_ifmedia_upd __P((struct ifnet *)); 218 Static void aue_ifmedia_sts __P((struct ifnet *, struct ifmediareq *)); 219 220 Static int aue_eeprom_getword __P((struct aue_softc *, int)); 221 Static void aue_read_mac __P((struct aue_softc *, u_char *)); 222 Static int aue_miibus_readreg __P((device_ptr_t, int, int)); 223 #if defined(__FreeBSD__) 224 Static int aue_miibus_writereg __P((device_ptr_t, int, int, int)); 225 #elif defined(__NetBSD__) || defined(__OpenBSD__) 226 Static void aue_miibus_writereg __P((device_ptr_t, int, int, int)); 227 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 228 Static void aue_miibus_statchg __P((device_ptr_t)); 229 230 Static void aue_setmulti __P((struct aue_softc *)); 231 Static u_int32_t aue_crc __P((caddr_t)); 232 Static void aue_reset __P((struct aue_softc *)); 233 234 Static int aue_csr_read_1 __P((struct aue_softc *, int)); 235 Static int aue_csr_write_1 __P((struct aue_softc *, int, int)); 236 Static int aue_csr_read_2 __P((struct aue_softc *, int)); 237 Static int aue_csr_write_2 __P((struct aue_softc *, int, int)); 238 239 #if defined(__FreeBSD__) 240 #if !defined(lint) 241 static const char rcsid[] = 242 "$FreeBSD: src/sys/dev/usb/if_aue.c,v 1.11 2000/01/14 01:36:14 wpaul Exp $"; 243 #endif 244 245 Static void aue_rxstart __P((struct ifnet *)); 246 247 Static struct usb_qdat aue_qdat; 248 249 Static device_method_t aue_methods[] = { 250 /* Device interface */ 251 DEVMETHOD(device_probe, aue_match), 252 DEVMETHOD(device_attach, aue_attach), 253 DEVMETHOD(device_detach, aue_detach), 254 DEVMETHOD(device_shutdown, aue_shutdown), 255 256 /* bus interface */ 257 DEVMETHOD(bus_print_child, bus_generic_print_child), 258 DEVMETHOD(bus_driver_added, bus_generic_driver_added), 259 260 /* MII interface */ 261 DEVMETHOD(miibus_readreg, aue_miibus_readreg), 262 DEVMETHOD(miibus_writereg, aue_miibus_writereg), 263 DEVMETHOD(miibus_statchg, aue_miibus_statchg), 264 265 { 0, 0 } 266 }; 267 268 Static driver_t aue_driver = { 269 "aue", 270 aue_methods, 271 sizeof(struct aue_softc) 272 }; 273 274 Static devclass_t aue_devclass; 275 276 DRIVER_MODULE(if_aue, uhub, aue_driver, aue_devclass, usbd_driver_load, 0); 277 DRIVER_MODULE(miibus, aue, miibus_driver, miibus_devclass, 0, 0); 278 279 #endif /* __FreeBSD__ */ 280 281 #define AUE_DO_REQUEST(dev, req, data) \ 282 usbd_do_request_flags(dev, req, data, USBD_NO_TSLEEP, NULL) 283 284 #define AUE_SETBIT(sc, reg, x) \ 285 aue_csr_write_1(sc, reg, aue_csr_read_1(sc, reg) | (x)) 286 287 #define AUE_CLRBIT(sc, reg, x) \ 288 aue_csr_write_1(sc, reg, aue_csr_read_1(sc, reg) & ~(x)) 289 290 Static int 291 aue_csr_read_1(sc, reg) 292 struct aue_softc *sc; 293 int reg; 294 { 295 usb_device_request_t req; 296 usbd_status err; 297 uByte val = 0; 298 int s; 299 300 if (sc->aue_dying) 301 return (0); 302 303 req.bmRequestType = UT_READ_VENDOR_DEVICE; 304 req.bRequest = AUE_UR_READREG; 305 USETW(req.wValue, 0); 306 USETW(req.wIndex, reg); 307 USETW(req.wLength, 1); 308 309 s = splusb(); 310 err = AUE_DO_REQUEST(sc->aue_udev, &req, &val); 311 splx(s); 312 313 if (err) { 314 DPRINTF(("%s: aue_csr_read_1: reg=0x%x err=%s\n", 315 USBDEVNAME(sc->aue_dev), reg, usbd_errstr(err))); 316 return (0); 317 } 318 319 return (val); 320 } 321 322 Static int 323 aue_csr_read_2(sc, reg) 324 struct aue_softc *sc; 325 int reg; 326 { 327 usb_device_request_t req; 328 usbd_status err; 329 uWord val; 330 int s; 331 332 if (sc->aue_dying) 333 return (0); 334 335 req.bmRequestType = UT_READ_VENDOR_DEVICE; 336 req.bRequest = AUE_UR_READREG; 337 USETW(req.wValue, 0); 338 USETW(req.wIndex, reg); 339 USETW(req.wLength, 2); 340 341 s = splusb(); 342 err = AUE_DO_REQUEST(sc->aue_udev, &req, &val); 343 splx(s); 344 345 if (err) { 346 DPRINTF(("%s: aue_csr_read_2: reg=0x%x err=%s\n", 347 USBDEVNAME(sc->aue_dev), reg, usbd_errstr(err))); 348 return (0); 349 } 350 351 return (UGETW(val)); 352 } 353 354 Static int 355 aue_csr_write_1(sc, reg, aval) 356 struct aue_softc *sc; 357 int reg, aval; 358 { 359 usb_device_request_t req; 360 usbd_status err; 361 int s; 362 uByte val; 363 364 if (sc->aue_dying) 365 return (0); 366 367 val = aval; 368 req.bmRequestType = UT_WRITE_VENDOR_DEVICE; 369 req.bRequest = AUE_UR_WRITEREG; 370 USETW(req.wValue, val); 371 USETW(req.wIndex, reg); 372 USETW(req.wLength, 1); 373 374 s = splusb(); 375 err = AUE_DO_REQUEST(sc->aue_udev, &req, &val); 376 splx(s); 377 378 if (err) { 379 DPRINTF(("%s: aue_csr_write_1: reg=0x%x err=%s\n", 380 USBDEVNAME(sc->aue_dev), reg, usbd_errstr(err))); 381 return (-1); 382 } 383 384 return (0); 385 } 386 387 Static int 388 aue_csr_write_2(sc, reg, aval) 389 struct aue_softc *sc; 390 int reg, aval; 391 { 392 usb_device_request_t req; 393 usbd_status err; 394 int s; 395 uWord val; 396 397 if (sc->aue_dying) 398 return (0); 399 400 USETW(val, aval); 401 req.bmRequestType = UT_WRITE_VENDOR_DEVICE; 402 req.bRequest = AUE_UR_WRITEREG; 403 USETW(req.wValue, aval); 404 USETW(req.wIndex, reg); 405 USETW(req.wLength, 2); 406 407 s = splusb(); 408 err = AUE_DO_REQUEST(sc->aue_udev, &req, &val); 409 splx(s); 410 411 if (err) { 412 DPRINTF(("%s: aue_csr_write_2: reg=0x%x err=%s\n", 413 USBDEVNAME(sc->aue_dev), reg, usbd_errstr(err))); 414 return (-1); 415 } 416 417 return (0); 418 } 419 420 /* 421 * Read a word of data stored in the EEPROM at address 'addr.' 422 */ 423 Static int 424 aue_eeprom_getword(sc, addr) 425 struct aue_softc *sc; 426 int addr; 427 { 428 int i; 429 430 aue_csr_write_1(sc, AUE_EE_REG, addr); 431 aue_csr_write_1(sc, AUE_EE_CTL, AUE_EECTL_READ); 432 433 for (i = 0; i < AUE_TIMEOUT; i++) { 434 if (aue_csr_read_1(sc, AUE_EE_CTL) & AUE_EECTL_DONE) 435 break; 436 } 437 438 if (i == AUE_TIMEOUT) { 439 printf("%s: EEPROM read timed out\n", 440 USBDEVNAME(sc->aue_dev)); 441 } 442 443 return (aue_csr_read_2(sc, AUE_EE_DATA)); 444 } 445 446 /* 447 * Read the MAC from the EEPROM. It's at offset 0. 448 */ 449 Static void 450 aue_read_mac(sc, dest) 451 struct aue_softc *sc; 452 u_char *dest; 453 { 454 int i; 455 int off = 0; 456 int word; 457 458 DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 459 460 for (i = 0; i < 3; i++) { 461 word = aue_eeprom_getword(sc, off + i); 462 dest[2 * i] = (u_char)word; 463 dest[2 * i + 1] = (u_char)(word >> 8); 464 } 465 } 466 467 Static int 468 aue_miibus_readreg(dev, phy, reg) 469 device_ptr_t dev; 470 int phy, reg; 471 { 472 struct aue_softc *sc = USBGETSOFTC(dev); 473 int i; 474 u_int16_t val; 475 476 /* 477 * The Am79C901 HomePNA PHY actually contains 478 * two transceivers: a 1Mbps HomePNA PHY and a 479 * 10Mbps full/half duplex ethernet PHY with 480 * NWAY autoneg. However in the ADMtek adapter, 481 * only the 1Mbps PHY is actually connected to 482 * anything, so we ignore the 10Mbps one. It 483 * happens to be configured for MII address 3, 484 * so we filter that out. 485 */ 486 if (sc->aue_vendor == USB_VENDOR_ADMTEK && 487 sc->aue_product == USB_PRODUCT_ADMTEK_PEGASUS) { 488 if (phy != 1) 489 return (0); 490 } 491 492 aue_csr_write_1(sc, AUE_PHY_ADDR, phy); 493 aue_csr_write_1(sc, AUE_PHY_CTL, reg | AUE_PHYCTL_READ); 494 495 for (i = 0; i < AUE_TIMEOUT; i++) { 496 if (aue_csr_read_1(sc, AUE_PHY_CTL) & AUE_PHYCTL_DONE) 497 break; 498 } 499 500 if (i == AUE_TIMEOUT) { 501 printf("%s: MII read timed out\n", 502 USBDEVNAME(sc->aue_dev)); 503 } 504 505 val = aue_csr_read_2(sc, AUE_PHY_DATA); 506 507 DPRINTFN(11,("%s: %s: phy=%d reg=%d => 0x%04x\n", 508 USBDEVNAME(sc->aue_dev), __FUNCTION__, phy, reg, val)); 509 510 return (val); 511 } 512 513 #if defined(__FreeBSD__) 514 Static int 515 #elif defined(__NetBSD__) || defined(__OpenBSD__) 516 Static void 517 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 518 aue_miibus_writereg(dev, phy, reg, data) 519 device_ptr_t dev; 520 int phy, reg, data; 521 { 522 struct aue_softc *sc = USBGETSOFTC(dev); 523 int i; 524 525 if (sc->aue_vendor == USB_VENDOR_ADMTEK && 526 sc->aue_product == USB_PRODUCT_ADMTEK_PEGASUS) { 527 if (phy == 3) 528 #if defined(__FreeBSD__) 529 return (0); 530 #elif defined(__NetBSD__) || defined(__OpenBSD__) 531 return; 532 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 533 } 534 535 DPRINTFN(11,("%s: %s: phy=%d reg=%d data=0x%04x\n", 536 USBDEVNAME(sc->aue_dev), __FUNCTION__, phy, reg, data)); 537 538 aue_csr_write_2(sc, AUE_PHY_DATA, data); 539 aue_csr_write_1(sc, AUE_PHY_ADDR, phy); 540 aue_csr_write_1(sc, AUE_PHY_CTL, reg | AUE_PHYCTL_WRITE); 541 542 for (i = 0; i < AUE_TIMEOUT; i++) { 543 if (aue_csr_read_1(sc, AUE_PHY_CTL) & AUE_PHYCTL_DONE) 544 break; 545 } 546 547 if (i == AUE_TIMEOUT) { 548 printf("%s: MII read timed out\n", 549 USBDEVNAME(sc->aue_dev)); 550 } 551 552 #if defined(__FreeBSD__) 553 return (0); 554 #endif 555 } 556 557 Static void 558 aue_miibus_statchg(dev) 559 device_ptr_t dev; 560 { 561 struct aue_softc *sc = USBGETSOFTC(dev); 562 struct mii_data *mii = GET_MII(sc); 563 564 DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 565 566 AUE_CLRBIT(sc, AUE_CTL0, AUE_CTL0_RX_ENB | AUE_CTL0_TX_ENB); 567 568 if (IFM_SUBTYPE(mii->mii_media_active) == IFM_100_TX) { 569 AUE_SETBIT(sc, AUE_CTL1, AUE_CTL1_SPEEDSEL); 570 } else { 571 AUE_CLRBIT(sc, AUE_CTL1, AUE_CTL1_SPEEDSEL); 572 } 573 574 if ((mii->mii_media_active & IFM_GMASK) == IFM_FDX) 575 AUE_SETBIT(sc, AUE_CTL1, AUE_CTL1_DUPLEX); 576 else 577 AUE_CLRBIT(sc, AUE_CTL1, AUE_CTL1_DUPLEX); 578 579 AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_RX_ENB | AUE_CTL0_TX_ENB); 580 581 /* 582 * Set the LED modes on the LinkSys adapter. 583 * This turns on the 'dual link LED' bin in the auxmode 584 * register of the Broadcom PHY. 585 */ 586 if ((sc->aue_vendor == USB_VENDOR_LINKSYS && 587 sc->aue_product == USB_PRODUCT_LINKSYS_USB100TX) || 588 (sc->aue_vendor == USB_VENDOR_DLINK && 589 sc->aue_product == USB_PRODUCT_DLINK_DSB650TX)) { 590 u_int16_t auxmode; 591 auxmode = aue_miibus_readreg(dev, 0, 0x1b); 592 aue_miibus_writereg(dev, 0, 0x1b, auxmode | 0x04); 593 } 594 } 595 596 #define AUE_POLY 0xEDB88320 597 #define AUE_BITS 6 598 599 Static u_int32_t 600 aue_crc(addr) 601 caddr_t addr; 602 { 603 u_int32_t idx, bit, data, crc; 604 605 /* Compute CRC for the address value. */ 606 crc = 0xFFFFFFFF; /* initial value */ 607 608 for (idx = 0; idx < 6; idx++) { 609 for (data = *addr++, bit = 0; bit < 8; bit++, data >>= 1) 610 crc = (crc >> 1) ^ (((crc ^ data) & 1) ? AUE_POLY : 0); 611 } 612 613 return (crc & ((1 << AUE_BITS) - 1)); 614 } 615 616 Static void 617 aue_setmulti(sc) 618 struct aue_softc *sc; 619 { 620 struct ifnet *ifp; 621 #if defined(__FreeBSD__) 622 struct ifmultiaddr *ifma; 623 #elif defined(__NetBSD__) || defined(__OpenBSD__) 624 struct ether_multi *enm; 625 struct ether_multistep step; 626 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 627 u_int32_t h = 0, i; 628 629 DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 630 631 ifp = GET_IFP(sc); 632 633 if (ifp->if_flags & IFF_ALLMULTI || ifp->if_flags & IFF_PROMISC) { 634 AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_ALLMULTI); 635 return; 636 } 637 638 AUE_CLRBIT(sc, AUE_CTL0, AUE_CTL0_ALLMULTI); 639 640 /* first, zot all the existing hash bits */ 641 for (i = 0; i < 8; i++) 642 aue_csr_write_1(sc, AUE_MAR0 + i, 0); 643 644 /* now program new ones */ 645 #if defined(__FreeBSD__) 646 for (ifma = ifp->if_multiaddrs.lh_first; ifma != NULL; 647 ifma = ifma->ifma_link.le_next) { 648 if (ifma->ifma_addr->sa_family != AF_LINK) 649 continue; 650 h = aue_crc(LLADDR((struct sockaddr_dl *)ifma->ifma_addr)); 651 AUE_SETBIT(sc, AUE_MAR + (h >> 3), 1 << (h & 0xF)); 652 } 653 #elif defined(__NetBSD__) || defined(__OpenBSD__) 654 #if defined(__NetBSD__) 655 ETHER_FIRST_MULTI(step, &sc->aue_ec, enm); 656 #else 657 ETHER_FIRST_MULTI(step, &sc->arpcom, enm); 658 #endif 659 while (enm != NULL) { 660 #if 1 661 if (memcmp(enm->enm_addrlo, 662 enm->enm_addrhi, ETHER_ADDR_LEN) != 0) { 663 ifp->if_flags |= IFF_ALLMULTI; 664 AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_ALLMULTI); 665 return; 666 } 667 #endif 668 h = aue_crc(enm->enm_addrlo); 669 AUE_SETBIT(sc, AUE_MAR + (h >> 3), 1 << (h & 0xF)); 670 ETHER_NEXT_MULTI(step, enm); 671 } 672 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 673 } 674 675 Static void 676 aue_reset(sc) 677 struct aue_softc *sc; 678 { 679 int i; 680 681 DPRINTFN(2,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 682 683 AUE_SETBIT(sc, AUE_CTL1, AUE_CTL1_RESETMAC); 684 685 for (i = 0; i < AUE_TIMEOUT; i++) { 686 if (!(aue_csr_read_1(sc, AUE_CTL1) & AUE_CTL1_RESETMAC)) 687 break; 688 } 689 690 if (i == AUE_TIMEOUT) 691 printf("%s: reset failed\n", USBDEVNAME(sc->aue_dev)); 692 693 /* 694 * The PHY(s) attached to the Pegasus chip may be held 695 * in reset until we flip on the GPIO outputs. Make sure 696 * to set the GPIO pins high so that the PHY(s) will 697 * be enabled. 698 * 699 * Note: We force all of the GPIO pins low first, *then* 700 * enable the ones we want. 701 */ 702 aue_csr_write_1(sc, AUE_GPIO0, 703 AUE_GPIO_OUT0 | AUE_GPIO_SEL0); 704 aue_csr_write_1(sc, AUE_GPIO0, 705 AUE_GPIO_OUT0 | AUE_GPIO_SEL0 | AUE_GPIO_SEL1); 706 707 /* Grrr. LinkSys has to be different from everyone else. */ 708 if ((sc->aue_vendor == USB_VENDOR_LINKSYS && 709 sc->aue_product == USB_PRODUCT_LINKSYS_USB100TX) || 710 (sc->aue_vendor == USB_VENDOR_DLINK && 711 sc->aue_product == USB_PRODUCT_DLINK_DSB650TX)) { 712 aue_csr_write_1(sc, AUE_GPIO0, 713 AUE_GPIO_SEL0 | AUE_GPIO_SEL1); 714 aue_csr_write_1(sc, AUE_GPIO0, 715 AUE_GPIO_SEL0 | AUE_GPIO_SEL1 | AUE_GPIO_OUT0); 716 } 717 718 /* Wait a little while for the chip to get its brains in order. */ 719 delay(10000); /* XXX */ 720 } 721 722 /* 723 * Probe for a Pegasus chip. 724 */ 725 USB_MATCH(aue) 726 { 727 USB_MATCH_START(aue, uaa); 728 struct aue_type *t; 729 730 if (uaa->iface != NULL) 731 return (UMATCH_NONE); 732 733 for (t = aue_devs; t->aue_vid != 0; t++) 734 if (uaa->vendor == t->aue_vid && uaa->product == t->aue_did) 735 return (UMATCH_VENDOR_PRODUCT); 736 737 return (UMATCH_NONE); 738 } 739 740 /* 741 * Attach the interface. Allocate softc structures, do ifmedia 742 * setup and ethernet/BPF attach. 743 */ 744 USB_ATTACH(aue) 745 { 746 USB_ATTACH_START(aue, sc, uaa); 747 char devinfo[1024]; 748 int s; 749 u_char eaddr[ETHER_ADDR_LEN]; 750 struct ifnet *ifp; 751 struct mii_data *mii; 752 usbd_device_handle dev = uaa->device; 753 usbd_interface_handle iface; 754 usbd_status err; 755 usb_interface_descriptor_t *id; 756 usb_endpoint_descriptor_t *ed; 757 int i; 758 759 #ifdef __FreeBSD__ 760 bzero(sc, sizeof(struct aue_softc)); 761 #endif 762 763 DPRINTFN(5,(" : aue_attach: sc=%p", sc)); 764 765 usbd_devinfo(dev, 0, devinfo); 766 USB_ATTACH_SETUP; 767 printf("%s: %s\n", USBDEVNAME(sc->aue_dev), devinfo); 768 769 err = usbd_set_config_no(dev, AUE_CONFIG_NO, 0); 770 if (err) { 771 printf("%s: setting config no failed\n", 772 USBDEVNAME(sc->aue_dev)); 773 USB_ATTACH_ERROR_RETURN; 774 } 775 776 err = usbd_device2interface_handle(dev, AUE_IFACE_IDX, &iface); 777 if (err) { 778 printf("%s: getting interface handle failed\n", 779 USBDEVNAME(sc->aue_dev)); 780 USB_ATTACH_ERROR_RETURN; 781 } 782 783 sc->aue_udev = dev; 784 sc->aue_iface = iface; 785 sc->aue_product = uaa->product; 786 sc->aue_vendor = uaa->vendor; 787 788 id = usbd_get_interface_descriptor(iface); 789 790 /* Find endpoints. */ 791 for (i = 0; i < id->bNumEndpoints; i++) { 792 ed = usbd_interface2endpoint_descriptor(iface, i); 793 if (ed == NULL) { 794 printf("%s: couldn't get endpoint descriptor %d\n", 795 USBDEVNAME(sc->aue_dev), i); 796 USB_ATTACH_ERROR_RETURN; 797 } 798 if (UE_GET_DIR(ed->bEndpointAddress) == UE_DIR_IN && 799 UE_GET_XFERTYPE(ed->bmAttributes) == UE_BULK) { 800 sc->aue_ed[AUE_ENDPT_RX] = ed->bEndpointAddress; 801 } else if (UE_GET_DIR(ed->bEndpointAddress) == UE_DIR_OUT && 802 UE_GET_XFERTYPE(ed->bmAttributes) == UE_BULK) { 803 sc->aue_ed[AUE_ENDPT_TX] = ed->bEndpointAddress; 804 } else if (UE_GET_DIR(ed->bEndpointAddress) == UE_DIR_IN && 805 UE_GET_XFERTYPE(ed->bmAttributes) == UE_INTERRUPT) { 806 sc->aue_ed[AUE_ENDPT_INTR] = ed->bEndpointAddress; 807 } 808 } 809 810 if (sc->aue_ed[AUE_ENDPT_RX] == 0 || sc->aue_ed[AUE_ENDPT_TX] == 0 || 811 sc->aue_ed[AUE_ENDPT_INTR] == 0) { 812 printf("%s: missing endpoint\n", USBDEVNAME(sc->aue_dev)); 813 USB_ATTACH_ERROR_RETURN; 814 } 815 816 817 s = splimp(); 818 819 /* Reset the adapter. */ 820 aue_reset(sc); 821 822 /* 823 * Get station address from the EEPROM. 824 */ 825 aue_read_mac(sc, eaddr); 826 827 /* 828 * A Pegasus chip was detected. Inform the world. 829 */ 830 ifp = GET_IFP(sc); 831 #if defined(__FreeBSD__) 832 printf("%s: Ethernet address: %6D\n", USBDEVNAME(sc->aue_dev), 833 eaddr, ":"); 834 835 bcopy(eaddr, (char *)&sc->arpcom.ac_enaddr, ETHER_ADDR_LEN); 836 837 ifp->if_softc = sc; 838 ifp->if_unit = sc->aue_unit; 839 ifp->if_name = "aue"; 840 ifp->if_mtu = ETHERMTU; 841 ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; 842 ifp->if_ioctl = aue_ioctl; 843 ifp->if_output = ether_output; 844 ifp->if_start = aue_start; 845 ifp->if_watchdog = aue_watchdog; 846 ifp->if_init = aue_init; 847 ifp->if_snd.ifq_maxlen = IFQ_MAXLEN; 848 849 /* 850 * Do MII setup. 851 * NOTE: Doing this causes child devices to be attached to us, 852 * which we would normally disconnect at in the detach routine 853 * using device_delete_child(). However the USB code is set up 854 * such that when this driver is removed, all childred devices 855 * are removed as well. In effect, the USB code ends up detaching 856 * all of our children for us, so we don't have to do is ourselves 857 * in aue_detach(). It's important to point this out since if 858 * we *do* try to detach the child devices ourselves, we will 859 * end up getting the children deleted twice, which will crash 860 * the system. 861 */ 862 if (mii_phy_probe(self, &sc->aue_miibus, 863 aue_ifmedia_upd, aue_ifmedia_sts)) { 864 printf("%s: MII without any PHY!\n", USBDEVNAME(sc->aue_dev)); 865 splx(s); 866 USB_ATTACH_ERROR_RETURN; 867 } 868 869 aue_qdat.ifp = ifp; 870 aue_qdat.if_rxstart = aue_rxstart; 871 872 /* 873 * Call MI attach routines. 874 */ 875 if_attach(ifp); 876 ether_ifattach(ifp); 877 bpfattach(ifp, DLT_EN10MB, sizeof(struct ether_header)); 878 879 usb_register_netisr(); 880 881 #elif defined(__NetBSD__) || defined(__OpenBSD__) 882 883 printf("%s: Ethernet address %s\n", USBDEVNAME(sc->aue_dev), 884 ether_sprintf(eaddr)); 885 886 /* Initialize interface info.*/ 887 ifp->if_softc = sc; 888 ifp->if_mtu = ETHERMTU; 889 ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; 890 ifp->if_ioctl = aue_ioctl; 891 ifp->if_start = aue_start; 892 ifp->if_watchdog = aue_watchdog; 893 #if defined(__OpenBSD__) 894 ifp->if_snd.ifq_maxlen = IFQ_MAXLEN; 895 #endif 896 strncpy(ifp->if_xname, USBDEVNAME(sc->aue_dev), IFNAMSIZ); 897 898 /* Initialize MII/media info. */ 899 mii = &sc->aue_mii; 900 mii->mii_ifp = ifp; 901 mii->mii_readreg = aue_miibus_readreg; 902 mii->mii_writereg = aue_miibus_writereg; 903 mii->mii_statchg = aue_miibus_statchg; 904 ifmedia_init(&mii->mii_media, 0, aue_ifmedia_upd, aue_ifmedia_sts); 905 mii_attach(self, mii, 0xffffffff, MII_PHY_ANY, MII_OFFSET_ANY, 0); 906 if (LIST_FIRST(&mii->mii_phys) == NULL) { 907 ifmedia_add(&mii->mii_media, IFM_ETHER | IFM_NONE, 0, NULL); 908 ifmedia_set(&mii->mii_media, IFM_ETHER | IFM_NONE); 909 } else 910 ifmedia_set(&mii->mii_media, IFM_ETHER | IFM_AUTO); 911 912 /* Attach the interface. */ 913 if_attach(ifp); 914 Ether_ifattach(ifp, eaddr); 915 916 #if NBPFILTER > 0 917 bpfattach(&ifp->if_bpf, ifp, DLT_EN10MB, 918 sizeof(struct ether_header)); 919 #endif 920 #if NRND > 0 921 rnd_attach_source(&sc->rnd_source, USBDEVNAME(sc->aue_dev), 922 RND_TYPE_NET, 0); 923 #endif 924 925 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 926 927 usb_callout_init(sc->aue_stat_ch); 928 929 sc->aue_attached = 1; 930 splx(s); 931 932 usbd_add_drv_event(USB_EVENT_DRIVER_ATTACH, sc->aue_udev, 933 USBDEV(sc->aue_dev)); 934 935 USB_ATTACH_SUCCESS_RETURN; 936 } 937 938 USB_DETACH(aue) 939 { 940 USB_DETACH_START(aue, sc); 941 struct ifnet *ifp = GET_IFP(sc); 942 int s; 943 944 DPRINTFN(2,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 945 946 s = splusb(); 947 948 usb_uncallout(sc->aue_stat_ch, aue_tick, sc); 949 950 if (!sc->aue_attached) { 951 /* Detached before attached finished, so just bail out. */ 952 splx(s); 953 return (0); 954 } 955 956 if (ifp->if_flags & IFF_RUNNING) 957 aue_stop(sc); 958 959 #if defined(__NetBSD__) 960 #if NRND > 0 961 rnd_detach_source(&sc->rnd_source); 962 #endif 963 mii_detach(&sc->aue_mii, MII_PHY_ANY, MII_OFFSET_ANY); 964 ifmedia_delete_instance(&sc->aue_mii.mii_media, IFM_INST_ANY); 965 #if NBPFILTER > 0 966 bpfdetach(ifp); 967 #endif 968 ether_ifdetach(ifp); 969 #endif /* __NetBSD__ */ 970 971 if_detach(ifp); 972 973 #ifdef DIAGNOSTIC 974 if (sc->aue_ep[AUE_ENDPT_TX] != NULL || 975 sc->aue_ep[AUE_ENDPT_RX] != NULL || 976 sc->aue_ep[AUE_ENDPT_INTR] != NULL) 977 printf("%s: detach has active endpoints\n", 978 USBDEVNAME(sc->aue_dev)); 979 #endif 980 981 sc->aue_attached = 0; 982 splx(s); 983 984 usbd_add_drv_event(USB_EVENT_DRIVER_DETACH, sc->aue_udev, 985 USBDEV(sc->aue_dev)); 986 987 return (0); 988 } 989 990 #if defined(__NetBSD__) || defined(__OpenBSD__) 991 int 992 aue_activate(self, act) 993 device_ptr_t self; 994 enum devact act; 995 { 996 struct aue_softc *sc = (struct aue_softc *)self; 997 998 DPRINTFN(2,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 999 1000 switch (act) { 1001 case DVACT_ACTIVATE: 1002 return (EOPNOTSUPP); 1003 break; 1004 1005 case DVACT_DEACTIVATE: 1006 if_deactivate(&sc->aue_ec.ec_if); 1007 sc->aue_dying = 1; 1008 break; 1009 } 1010 return (0); 1011 } 1012 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 1013 1014 /* 1015 * Initialize an RX descriptor and attach an MBUF cluster. 1016 */ 1017 Static int 1018 aue_newbuf(sc, c, m) 1019 struct aue_softc *sc; 1020 struct aue_chain *c; 1021 struct mbuf *m; 1022 { 1023 struct mbuf *m_new = NULL; 1024 1025 DPRINTFN(10,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev),__FUNCTION__)); 1026 1027 if (m == NULL) { 1028 MGETHDR(m_new, M_DONTWAIT, MT_DATA); 1029 if (m_new == NULL) { 1030 printf("%s: no memory for rx list " 1031 "-- packet dropped!\n", USBDEVNAME(sc->aue_dev)); 1032 return (ENOBUFS); 1033 } 1034 1035 MCLGET(m_new, M_DONTWAIT); 1036 if (!(m_new->m_flags & M_EXT)) { 1037 printf("%s: no memory for rx list " 1038 "-- packet dropped!\n", USBDEVNAME(sc->aue_dev)); 1039 m_freem(m_new); 1040 return (ENOBUFS); 1041 } 1042 m_new->m_len = m_new->m_pkthdr.len = MCLBYTES; 1043 } else { 1044 m_new = m; 1045 m_new->m_len = m_new->m_pkthdr.len = MCLBYTES; 1046 m_new->m_data = m_new->m_ext.ext_buf; 1047 } 1048 1049 m_adj(m_new, ETHER_ALIGN); 1050 c->aue_mbuf = m_new; 1051 1052 return (0); 1053 } 1054 1055 Static int 1056 aue_rx_list_init(sc) 1057 struct aue_softc *sc; 1058 { 1059 struct aue_cdata *cd; 1060 struct aue_chain *c; 1061 int i; 1062 1063 DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 1064 1065 cd = &sc->aue_cdata; 1066 for (i = 0; i < AUE_RX_LIST_CNT; i++) { 1067 c = &cd->aue_rx_chain[i]; 1068 c->aue_sc = sc; 1069 c->aue_idx = i; 1070 if (aue_newbuf(sc, c, NULL) == ENOBUFS) 1071 return (ENOBUFS); 1072 if (c->aue_xfer == NULL) { 1073 c->aue_xfer = usbd_alloc_xfer(sc->aue_udev); 1074 if (c->aue_xfer == NULL) 1075 return (ENOBUFS); 1076 c->aue_buf = usbd_alloc_buffer(c->aue_xfer, AUE_BUFSZ); 1077 if (c->aue_buf == NULL) 1078 return (ENOBUFS); /* XXX free xfer */ 1079 } 1080 } 1081 1082 return (0); 1083 } 1084 1085 Static int 1086 aue_tx_list_init(sc) 1087 struct aue_softc *sc; 1088 { 1089 struct aue_cdata *cd; 1090 struct aue_chain *c; 1091 int i; 1092 1093 DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 1094 1095 cd = &sc->aue_cdata; 1096 for (i = 0; i < AUE_TX_LIST_CNT; i++) { 1097 c = &cd->aue_tx_chain[i]; 1098 c->aue_sc = sc; 1099 c->aue_idx = i; 1100 c->aue_mbuf = NULL; 1101 if (c->aue_xfer == NULL) { 1102 c->aue_xfer = usbd_alloc_xfer(sc->aue_udev); 1103 if (c->aue_xfer == NULL) 1104 return (ENOBUFS); 1105 c->aue_buf = usbd_alloc_buffer(c->aue_xfer, AUE_BUFSZ); 1106 if (c->aue_buf == NULL) 1107 return (ENOBUFS); 1108 } 1109 } 1110 1111 return (0); 1112 } 1113 1114 Static void 1115 aue_intr(xfer, priv, status) 1116 usbd_xfer_handle xfer; 1117 usbd_private_handle priv; 1118 usbd_status status; 1119 { 1120 struct aue_softc *sc = priv; 1121 struct ifnet *ifp = GET_IFP(sc); 1122 struct aue_intrpkt *p = &sc->aue_cdata.aue_ibuf; 1123 1124 DPRINTFN(15,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev),__FUNCTION__)); 1125 1126 if (sc->aue_dying) 1127 return; 1128 1129 if (!(ifp->if_flags & IFF_RUNNING)) 1130 return; 1131 1132 if (status != USBD_NORMAL_COMPLETION) { 1133 if (status == USBD_NOT_STARTED || status == USBD_CANCELLED) { 1134 return; 1135 } 1136 printf("%s: usb error on intr: %s\n", USBDEVNAME(sc->aue_dev), 1137 usbd_errstr(status)); 1138 if (status == USBD_STALLED) 1139 usbd_clear_endpoint_stall(sc->aue_ep[AUE_ENDPT_RX]); 1140 return; 1141 } 1142 1143 if (p->aue_txstat0) 1144 ifp->if_oerrors++; 1145 1146 if (p->aue_txstat0 & (AUE_TXSTAT0_LATECOLL | AUE_TXSTAT0_EXCESSCOLL)) 1147 ifp->if_collisions++; 1148 } 1149 1150 #if defined(__FreeBSD__) 1151 Static void 1152 aue_rxstart(ifp) 1153 struct ifnet *ifp; 1154 { 1155 struct aue_softc *sc; 1156 struct aue_chain *c; 1157 1158 sc = ifp->if_softc; 1159 c = &sc->aue_cdata.aue_rx_chain[sc->aue_cdata.aue_rx_prod]; 1160 1161 if (aue_newbuf(sc, c, NULL) == ENOBUFS) { 1162 ifp->if_ierrors++; 1163 return; 1164 } 1165 1166 /* Setup new transfer. */ 1167 usbd_setup_xfer(c->aue_xfer, sc->aue_ep[AUE_ENDPT_RX], 1168 c, mtod(c->aue_mbuf, char *), AUE_BUFSZ, USBD_SHORT_XFER_OK, 1169 USBD_NO_TIMEOUT, aue_rxeof); 1170 usbd_transfer(c->aue_xfer); 1171 } 1172 #endif 1173 1174 /* 1175 * A frame has been uploaded: pass the resulting mbuf chain up to 1176 * the higher level protocols. 1177 * 1178 * Grrr. Receiving transfers larger than about 1152 bytes sometimes 1179 * doesn't work. We get an incomplete frame. In order to avoid 1180 * this, we queue up RX transfers that are shorter than a full sized 1181 * frame. If the received frame is larger than our transfer size, 1182 * we snag the rest of the data using a second transfer. Does this 1183 * hurt performance? Yes. But after fighting with this stupid thing 1184 * for three days, I'm willing to settle. I'd rather have reliable 1185 * receive performance that fast but spotty performance. 1186 */ 1187 Static void 1188 aue_rxeof(xfer, priv, status) 1189 usbd_xfer_handle xfer; 1190 usbd_private_handle priv; 1191 usbd_status status; 1192 { 1193 struct aue_chain *c = priv; 1194 struct aue_softc *sc = c->aue_sc; 1195 struct ifnet *ifp = GET_IFP(sc); 1196 struct mbuf *m; 1197 u_int32_t total_len; 1198 struct aue_rxpkt r; 1199 #if defined(__NetBSD__) || defined(__OpenBSD__) 1200 int s; 1201 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 1202 1203 DPRINTFN(10,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev),__FUNCTION__)); 1204 1205 if (sc->aue_dying) 1206 return; 1207 1208 if (!(ifp->if_flags & IFF_RUNNING)) 1209 return; 1210 1211 if (status != USBD_NORMAL_COMPLETION) { 1212 if (status == USBD_NOT_STARTED || status == USBD_CANCELLED) 1213 return; 1214 sc->aue_rx_errs++; 1215 if (usbd_ratecheck(&sc->aue_rx_notice)) { 1216 printf("%s: %u usb errors on rx: %s\n", 1217 USBDEVNAME(sc->aue_dev), sc->aue_rx_errs, 1218 usbd_errstr(status)); 1219 sc->aue_rx_errs = 0; 1220 } 1221 if (status == USBD_STALLED) 1222 usbd_clear_endpoint_stall(sc->aue_ep[AUE_ENDPT_RX]); 1223 goto done; 1224 } 1225 1226 usbd_get_xfer_status(xfer, NULL, NULL, &total_len, NULL); 1227 1228 memcpy(mtod(c->aue_mbuf, char*), c->aue_buf, total_len); 1229 1230 if (total_len <= 4 + ETHER_CRC_LEN) { 1231 ifp->if_ierrors++; 1232 goto done; 1233 } 1234 1235 memcpy(&r, c->aue_buf + total_len - 4, sizeof(r)); 1236 1237 /* Turn off all the non-error bits in the rx status word. */ 1238 r.aue_rxstat &= AUE_RXSTAT_MASK; 1239 if (r.aue_rxstat) { 1240 ifp->if_ierrors++; 1241 goto done; 1242 } 1243 1244 /* No errors; receive the packet. */ 1245 m = c->aue_mbuf; 1246 total_len -= ETHER_CRC_LEN + 4; 1247 m->m_pkthdr.len = m->m_len = total_len; 1248 ifp->if_ipackets++; 1249 1250 #if defined(__FreeBSD__) 1251 m->m_pkthdr.rcvif = (struct ifnet *)&kue_qdat; 1252 /* Put the packet on the special USB input queue. */ 1253 usb_ether_input(m); 1254 1255 return; 1256 1257 #elif defined(__NetBSD__) || defined(__OpenBSD__) 1258 m->m_pkthdr.rcvif = ifp; 1259 1260 s = splimp(); 1261 1262 /* XXX ugly */ 1263 if (aue_newbuf(sc, c, NULL) == ENOBUFS) { 1264 ifp->if_ierrors++; 1265 goto done1; 1266 } 1267 1268 #if NBPFILTER > 0 1269 /* 1270 * Handle BPF listeners. Let the BPF user see the packet, but 1271 * don't pass it up to the ether_input() layer unless it's 1272 * a broadcast packet, multicast packet, matches our ethernet 1273 * address or the interface is in promiscuous mode. 1274 */ 1275 if (ifp->if_bpf) { 1276 #if defined(__NetBSD__) 1277 struct ether_header *eh = mtod(m, struct ether_header *); 1278 BPF_MTAP(ifp, m); 1279 if ((ifp->if_flags & IFF_PROMISC) && 1280 memcmp(eh->ether_dhost, LLADDR(ifp->if_sadl), 1281 ETHER_ADDR_LEN) && 1282 !(eh->ether_dhost[0] & 1)) { 1283 m_freem(m); 1284 goto done1; 1285 } 1286 #else 1287 BPF_MTAP(ifp, m); 1288 #endif 1289 } 1290 #endif 1291 1292 DPRINTFN(10,("%s: %s: deliver %d\n", USBDEVNAME(sc->aue_dev), 1293 __FUNCTION__, m->m_len)); 1294 IF_INPUT(ifp, m); 1295 done1: 1296 splx(s); 1297 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 1298 1299 done: 1300 1301 /* Setup new transfer. */ 1302 usbd_setup_xfer(xfer, sc->aue_ep[AUE_ENDPT_RX], 1303 c, c->aue_buf, AUE_BUFSZ, 1304 USBD_SHORT_XFER_OK | USBD_NO_COPY, 1305 USBD_NO_TIMEOUT, aue_rxeof); 1306 usbd_transfer(xfer); 1307 1308 DPRINTFN(10,("%s: %s: start rx\n", USBDEVNAME(sc->aue_dev), 1309 __FUNCTION__)); 1310 } 1311 1312 /* 1313 * A frame was downloaded to the chip. It's safe for us to clean up 1314 * the list buffers. 1315 */ 1316 1317 Static void 1318 aue_txeof(xfer, priv, status) 1319 usbd_xfer_handle xfer; 1320 usbd_private_handle priv; 1321 usbd_status status; 1322 { 1323 struct aue_chain *c = priv; 1324 struct aue_softc *sc = c->aue_sc; 1325 struct ifnet *ifp = GET_IFP(sc); 1326 int s; 1327 1328 if (sc->aue_dying) 1329 return; 1330 1331 s = splimp(); 1332 1333 DPRINTFN(10,("%s: %s: enter status=%d\n", USBDEVNAME(sc->aue_dev), 1334 __FUNCTION__, status)); 1335 1336 ifp->if_timer = 0; 1337 ifp->if_flags &= ~IFF_OACTIVE; 1338 1339 if (status != USBD_NORMAL_COMPLETION) { 1340 if (status == USBD_NOT_STARTED || status == USBD_CANCELLED) { 1341 splx(s); 1342 return; 1343 } 1344 ifp->if_oerrors++; 1345 printf("%s: usb error on tx: %s\n", USBDEVNAME(sc->aue_dev), 1346 usbd_errstr(status)); 1347 if (status == USBD_STALLED) 1348 usbd_clear_endpoint_stall(sc->aue_ep[AUE_ENDPT_TX]); 1349 splx(s); 1350 return; 1351 } 1352 1353 ifp->if_opackets++; 1354 1355 #if defined(__FreeBSD__) 1356 c->aue_mbuf->m_pkthdr.rcvif = ifp; 1357 usb_tx_done(c->aue_mbuf); 1358 c->aue_mbuf = NULL; 1359 #elif defined(__NetBSD__) || defined(__OpenBSD__) 1360 m_freem(c->aue_mbuf); 1361 c->aue_mbuf = NULL; 1362 1363 if (ifp->if_snd.ifq_head != NULL) 1364 aue_start(ifp); 1365 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 1366 1367 splx(s); 1368 } 1369 1370 Static void 1371 aue_tick(xsc) 1372 void *xsc; 1373 { 1374 struct aue_softc *sc = xsc; 1375 struct ifnet *ifp; 1376 struct mii_data *mii; 1377 int s; 1378 1379 DPRINTFN(15,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev),__FUNCTION__)); 1380 1381 if (sc == NULL) 1382 return; 1383 1384 if (sc->aue_dying) 1385 return; 1386 1387 ifp = GET_IFP(sc); 1388 mii = GET_MII(sc); 1389 if (mii == NULL) 1390 return; 1391 1392 s = splimp(); 1393 1394 mii_tick(mii); 1395 if (!sc->aue_link) { 1396 mii_pollstat(mii); 1397 if (mii->mii_media_status & IFM_ACTIVE && 1398 IFM_SUBTYPE(mii->mii_media_active) != IFM_NONE) { 1399 DPRINTFN(2,("%s: %s: got link\n", 1400 USBDEVNAME(sc->aue_dev),__FUNCTION__)); 1401 sc->aue_link++; 1402 if (ifp->if_snd.ifq_head != NULL) 1403 aue_start(ifp); 1404 } 1405 } 1406 1407 usb_callout(sc->aue_stat_ch, hz, aue_tick, sc); 1408 1409 splx(s); 1410 } 1411 1412 Static int 1413 aue_send(sc, m, idx) 1414 struct aue_softc *sc; 1415 struct mbuf *m; 1416 int idx; 1417 { 1418 int total_len; 1419 struct aue_chain *c; 1420 usbd_status err; 1421 1422 DPRINTFN(10,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev),__FUNCTION__)); 1423 1424 c = &sc->aue_cdata.aue_tx_chain[idx]; 1425 1426 /* 1427 * Copy the mbuf data into a contiguous buffer, leaving two 1428 * bytes at the beginning to hold the frame length. 1429 */ 1430 m_copydata(m, 0, m->m_pkthdr.len, c->aue_buf + 2); 1431 c->aue_mbuf = m; 1432 1433 /* 1434 * The ADMtek documentation says that the packet length is 1435 * supposed to be specified in the first two bytes of the 1436 * transfer, however it actually seems to ignore this info 1437 * and base the frame size on the bulk transfer length. 1438 */ 1439 c->aue_buf[0] = (u_int8_t)m->m_pkthdr.len; 1440 c->aue_buf[1] = (u_int8_t)(m->m_pkthdr.len >> 8); 1441 total_len = m->m_pkthdr.len + 2; 1442 1443 usbd_setup_xfer(c->aue_xfer, sc->aue_ep[AUE_ENDPT_TX], 1444 c, c->aue_buf, total_len, USBD_FORCE_SHORT_XFER | USBD_NO_COPY, 1445 AUE_TX_TIMEOUT, aue_txeof); 1446 1447 /* Transmit */ 1448 err = usbd_transfer(c->aue_xfer); 1449 if (err != USBD_IN_PROGRESS) { 1450 aue_stop(sc); 1451 return (EIO); 1452 } 1453 DPRINTFN(5,("%s: %s: send %d bytes\n", USBDEVNAME(sc->aue_dev), 1454 __FUNCTION__, total_len)); 1455 1456 sc->aue_cdata.aue_tx_cnt++; 1457 1458 return (0); 1459 } 1460 1461 Static void 1462 aue_start(ifp) 1463 struct ifnet *ifp; 1464 { 1465 struct aue_softc *sc = ifp->if_softc; 1466 struct mbuf *m_head = NULL; 1467 1468 DPRINTFN(5,("%s: %s: enter, link=%d\n", USBDEVNAME(sc->aue_dev), 1469 __FUNCTION__, sc->aue_link)); 1470 1471 if (sc->aue_dying) 1472 return; 1473 1474 if (!sc->aue_link) 1475 return; 1476 1477 if (ifp->if_flags & IFF_OACTIVE) 1478 return; 1479 1480 IF_DEQUEUE(&ifp->if_snd, m_head); 1481 if (m_head == NULL) 1482 return; 1483 1484 if (aue_send(sc, m_head, 0)) { 1485 IF_PREPEND(&ifp->if_snd, m_head); 1486 ifp->if_flags |= IFF_OACTIVE; 1487 return; 1488 } 1489 1490 #if NBPFILTER > 0 1491 /* 1492 * If there's a BPF listener, bounce a copy of this frame 1493 * to him. 1494 */ 1495 if (ifp->if_bpf) 1496 BPF_MTAP(ifp, m_head); 1497 #endif 1498 1499 ifp->if_flags |= IFF_OACTIVE; 1500 1501 /* 1502 * Set a timeout in case the chip goes out to lunch. 1503 */ 1504 ifp->if_timer = 5; 1505 } 1506 1507 Static void 1508 aue_init(xsc) 1509 void *xsc; 1510 { 1511 struct aue_softc *sc = xsc; 1512 struct ifnet *ifp = GET_IFP(sc); 1513 struct mii_data *mii = GET_MII(sc); 1514 int i, s; 1515 u_char *eaddr; 1516 1517 DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 1518 1519 if (sc->aue_dying) 1520 return; 1521 1522 if (ifp->if_flags & IFF_RUNNING) 1523 return; 1524 1525 s = splimp(); 1526 1527 /* 1528 * Cancel pending I/O and free all RX/TX buffers. 1529 */ 1530 aue_reset(sc); 1531 1532 #if defined(__FreeBSD__) || defined(__OpenBSD__) 1533 eaddr = sc->arpcom.ac_enaddr; 1534 #elif defined(__NetBSD__) 1535 eaddr = LLADDR(ifp->if_sadl); 1536 #endif /* defined(__NetBSD__) */ 1537 for (i = 0; i < ETHER_ADDR_LEN; i++) 1538 aue_csr_write_1(sc, AUE_PAR0 + i, eaddr[i]); 1539 1540 /* If we want promiscuous mode, set the allframes bit. */ 1541 if (ifp->if_flags & IFF_PROMISC) 1542 AUE_SETBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC); 1543 else 1544 AUE_CLRBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC); 1545 1546 /* Init TX ring. */ 1547 if (aue_tx_list_init(sc) == ENOBUFS) { 1548 printf("%s: tx list init failed\n", USBDEVNAME(sc->aue_dev)); 1549 splx(s); 1550 return; 1551 } 1552 1553 /* Init RX ring. */ 1554 if (aue_rx_list_init(sc) == ENOBUFS) { 1555 printf("%s: rx list init failed\n", USBDEVNAME(sc->aue_dev)); 1556 splx(s); 1557 return; 1558 } 1559 1560 /* Load the multicast filter. */ 1561 aue_setmulti(sc); 1562 1563 /* Enable RX and TX */ 1564 aue_csr_write_1(sc, AUE_CTL0, AUE_CTL0_RXSTAT_APPEND | AUE_CTL0_RX_ENB); 1565 AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_TX_ENB); 1566 AUE_SETBIT(sc, AUE_CTL2, AUE_CTL2_EP3_CLR); 1567 1568 mii_mediachg(mii); 1569 1570 if (sc->aue_ep[AUE_ENDPT_RX] == NULL) { 1571 if (aue_openpipes(sc)) { 1572 splx(s); 1573 return; 1574 } 1575 } 1576 1577 ifp->if_flags |= IFF_RUNNING; 1578 ifp->if_flags &= ~IFF_OACTIVE; 1579 1580 splx(s); 1581 1582 usb_callout(sc->aue_stat_ch, hz, aue_tick, sc); 1583 } 1584 1585 Static int 1586 aue_openpipes(sc) 1587 struct aue_softc *sc; 1588 { 1589 struct aue_chain *c; 1590 usbd_status err; 1591 int i; 1592 1593 /* Open RX and TX pipes. */ 1594 err = usbd_open_pipe(sc->aue_iface, sc->aue_ed[AUE_ENDPT_RX], 1595 USBD_EXCLUSIVE_USE, &sc->aue_ep[AUE_ENDPT_RX]); 1596 if (err) { 1597 printf("%s: open rx pipe failed: %s\n", 1598 USBDEVNAME(sc->aue_dev), usbd_errstr(err)); 1599 return (EIO); 1600 } 1601 usbd_open_pipe(sc->aue_iface, sc->aue_ed[AUE_ENDPT_TX], 1602 USBD_EXCLUSIVE_USE, &sc->aue_ep[AUE_ENDPT_TX]); 1603 if (err) { 1604 printf("%s: open tx pipe failed: %s\n", 1605 USBDEVNAME(sc->aue_dev), usbd_errstr(err)); 1606 return (EIO); 1607 } 1608 err = usbd_open_pipe_intr(sc->aue_iface, sc->aue_ed[AUE_ENDPT_INTR], 1609 USBD_EXCLUSIVE_USE, &sc->aue_ep[AUE_ENDPT_INTR], sc, 1610 &sc->aue_cdata.aue_ibuf, AUE_INTR_PKTLEN, aue_intr, 1611 AUE_INTR_INTERVAL); 1612 if (err) { 1613 printf("%s: open intr pipe failed: %s\n", 1614 USBDEVNAME(sc->aue_dev), usbd_errstr(err)); 1615 return (EIO); 1616 } 1617 1618 /* Start up the receive pipe. */ 1619 for (i = 0; i < AUE_RX_LIST_CNT; i++) { 1620 c = &sc->aue_cdata.aue_rx_chain[i]; 1621 usbd_setup_xfer(c->aue_xfer, sc->aue_ep[AUE_ENDPT_RX], 1622 c, c->aue_buf, AUE_BUFSZ, 1623 USBD_SHORT_XFER_OK | USBD_NO_COPY, USBD_NO_TIMEOUT, 1624 aue_rxeof); 1625 (void)usbd_transfer(c->aue_xfer); /* XXX */ 1626 DPRINTFN(5,("%s: %s: start read\n", USBDEVNAME(sc->aue_dev), 1627 __FUNCTION__)); 1628 1629 } 1630 return (0); 1631 } 1632 1633 /* 1634 * Set media options. 1635 */ 1636 Static int 1637 aue_ifmedia_upd(ifp) 1638 struct ifnet *ifp; 1639 { 1640 struct aue_softc *sc = ifp->if_softc; 1641 struct mii_data *mii = GET_MII(sc); 1642 1643 DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 1644 1645 if (sc->aue_dying) 1646 return (0); 1647 1648 sc->aue_link = 0; 1649 if (mii->mii_instance) { 1650 struct mii_softc *miisc; 1651 for (miisc = LIST_FIRST(&mii->mii_phys); miisc != NULL; 1652 miisc = LIST_NEXT(miisc, mii_list)) 1653 mii_phy_reset(miisc); 1654 } 1655 mii_mediachg(mii); 1656 1657 return (0); 1658 } 1659 1660 /* 1661 * Report current media status. 1662 */ 1663 Static void 1664 aue_ifmedia_sts(ifp, ifmr) 1665 struct ifnet *ifp; 1666 struct ifmediareq *ifmr; 1667 { 1668 struct aue_softc *sc = ifp->if_softc; 1669 struct mii_data *mii = GET_MII(sc); 1670 1671 DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 1672 1673 mii_pollstat(mii); 1674 ifmr->ifm_active = mii->mii_media_active; 1675 ifmr->ifm_status = mii->mii_media_status; 1676 } 1677 1678 Static int 1679 aue_ioctl(ifp, command, data) 1680 struct ifnet *ifp; 1681 u_long command; 1682 caddr_t data; 1683 { 1684 struct aue_softc *sc = ifp->if_softc; 1685 #if defined(__NetBSD__) || defined(__OpenBSD__) 1686 struct ifaddr *ifa = (struct ifaddr *)data; 1687 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 1688 struct ifreq *ifr = (struct ifreq *)data; 1689 struct mii_data *mii; 1690 int s, error = 0; 1691 1692 if (sc->aue_dying) 1693 return (EIO); 1694 1695 s = splimp(); 1696 1697 switch(command) { 1698 #if defined(__FreeBSD__) 1699 case SIOCSIFADDR: 1700 case SIOCGIFADDR: 1701 case SIOCSIFMTU: 1702 error = ether_ioctl(ifp, command, data); 1703 break; 1704 #elif defined(__NetBSD__) || defined(__OpenBSD__) 1705 case SIOCSIFADDR: 1706 ifp->if_flags |= IFF_UP; 1707 aue_init(sc); 1708 1709 switch (ifa->ifa_addr->sa_family) { 1710 #ifdef INET 1711 case AF_INET: 1712 #if defined(__NetBSD__) 1713 arp_ifinit(ifp, ifa); 1714 #else 1715 arp_ifinit(&sc->arpcom, ifa); 1716 #endif 1717 break; 1718 #endif /* INET */ 1719 #ifdef NS 1720 case AF_NS: 1721 { 1722 struct ns_addr *ina = &IA_SNS(ifa)->sns_addr; 1723 1724 if (ns_nullhost(*ina)) 1725 ina->x_host = *(union ns_host *) 1726 LLADDR(ifp->if_sadl); 1727 else 1728 memcpy(LLADDR(ifp->if_sadl), 1729 ina->x_host.c_host, 1730 ifp->if_addrlen); 1731 break; 1732 } 1733 #endif /* NS */ 1734 } 1735 break; 1736 1737 case SIOCSIFMTU: 1738 if (ifr->ifr_mtu > ETHERMTU) 1739 error = EINVAL; 1740 else 1741 ifp->if_mtu = ifr->ifr_mtu; 1742 break; 1743 1744 #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ 1745 case SIOCSIFFLAGS: 1746 if (ifp->if_flags & IFF_UP) { 1747 if (ifp->if_flags & IFF_RUNNING && 1748 ifp->if_flags & IFF_PROMISC && 1749 !(sc->aue_if_flags & IFF_PROMISC)) { 1750 AUE_SETBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC); 1751 } else if (ifp->if_flags & IFF_RUNNING && 1752 !(ifp->if_flags & IFF_PROMISC) && 1753 sc->aue_if_flags & IFF_PROMISC) { 1754 AUE_CLRBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC); 1755 } else if (!(ifp->if_flags & IFF_RUNNING)) 1756 aue_init(sc); 1757 } else { 1758 if (ifp->if_flags & IFF_RUNNING) 1759 aue_stop(sc); 1760 } 1761 sc->aue_if_flags = ifp->if_flags; 1762 error = 0; 1763 break; 1764 case SIOCADDMULTI: 1765 case SIOCDELMULTI: 1766 aue_setmulti(sc); 1767 error = 0; 1768 break; 1769 case SIOCGIFMEDIA: 1770 case SIOCSIFMEDIA: 1771 mii = GET_MII(sc); 1772 error = ifmedia_ioctl(ifp, ifr, &mii->mii_media, command); 1773 break; 1774 default: 1775 error = EINVAL; 1776 break; 1777 } 1778 1779 splx(s); 1780 1781 return (error); 1782 } 1783 1784 Static void 1785 aue_watchdog(ifp) 1786 struct ifnet *ifp; 1787 { 1788 struct aue_softc *sc = ifp->if_softc; 1789 1790 DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 1791 1792 ifp->if_oerrors++; 1793 printf("%s: watchdog timeout\n", USBDEVNAME(sc->aue_dev)); 1794 1795 /* 1796 * The polling business is a kludge to avoid allowing the 1797 * USB code to call tsleep() in usbd_delay_ms(), which will 1798 * kill us since the watchdog routine is invoked from 1799 * interrupt context. 1800 */ 1801 usbd_set_polling(sc->aue_udev, 1); 1802 aue_stop(sc); 1803 aue_init(sc); 1804 usbd_set_polling(sc->aue_udev, 0); 1805 1806 if (ifp->if_snd.ifq_head != NULL) 1807 aue_start(ifp); 1808 } 1809 1810 /* 1811 * Stop the adapter and free any mbufs allocated to the 1812 * RX and TX lists. 1813 */ 1814 Static void 1815 aue_stop(sc) 1816 struct aue_softc *sc; 1817 { 1818 usbd_status err; 1819 struct ifnet *ifp; 1820 int i; 1821 1822 DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 1823 1824 ifp = GET_IFP(sc); 1825 ifp->if_timer = 0; 1826 1827 aue_csr_write_1(sc, AUE_CTL0, 0); 1828 aue_csr_write_1(sc, AUE_CTL1, 0); 1829 aue_reset(sc); 1830 usb_uncallout(sc->aue_stat_ch, aue_tick, sc); 1831 1832 /* Stop transfers. */ 1833 if (sc->aue_ep[AUE_ENDPT_RX] != NULL) { 1834 err = usbd_abort_pipe(sc->aue_ep[AUE_ENDPT_RX]); 1835 if (err) { 1836 printf("%s: abort rx pipe failed: %s\n", 1837 USBDEVNAME(sc->aue_dev), usbd_errstr(err)); 1838 } 1839 err = usbd_close_pipe(sc->aue_ep[AUE_ENDPT_RX]); 1840 if (err) { 1841 printf("%s: close rx pipe failed: %s\n", 1842 USBDEVNAME(sc->aue_dev), usbd_errstr(err)); 1843 } 1844 sc->aue_ep[AUE_ENDPT_RX] = NULL; 1845 } 1846 1847 if (sc->aue_ep[AUE_ENDPT_TX] != NULL) { 1848 err = usbd_abort_pipe(sc->aue_ep[AUE_ENDPT_TX]); 1849 if (err) { 1850 printf("%s: abort tx pipe failed: %s\n", 1851 USBDEVNAME(sc->aue_dev), usbd_errstr(err)); 1852 } 1853 err = usbd_close_pipe(sc->aue_ep[AUE_ENDPT_TX]); 1854 if (err) { 1855 printf("%s: close tx pipe failed: %s\n", 1856 USBDEVNAME(sc->aue_dev), usbd_errstr(err)); 1857 } 1858 sc->aue_ep[AUE_ENDPT_TX] = NULL; 1859 } 1860 1861 if (sc->aue_ep[AUE_ENDPT_INTR] != NULL) { 1862 err = usbd_abort_pipe(sc->aue_ep[AUE_ENDPT_INTR]); 1863 if (err) { 1864 printf("%s: abort intr pipe failed: %s\n", 1865 USBDEVNAME(sc->aue_dev), usbd_errstr(err)); 1866 } 1867 err = usbd_close_pipe(sc->aue_ep[AUE_ENDPT_INTR]); 1868 if (err) { 1869 printf("%s: close intr pipe failed: %s\n", 1870 USBDEVNAME(sc->aue_dev), usbd_errstr(err)); 1871 } 1872 sc->aue_ep[AUE_ENDPT_INTR] = NULL; 1873 } 1874 1875 /* Free RX resources. */ 1876 for (i = 0; i < AUE_RX_LIST_CNT; i++) { 1877 if (sc->aue_cdata.aue_rx_chain[i].aue_mbuf != NULL) { 1878 m_freem(sc->aue_cdata.aue_rx_chain[i].aue_mbuf); 1879 sc->aue_cdata.aue_rx_chain[i].aue_mbuf = NULL; 1880 } 1881 if (sc->aue_cdata.aue_rx_chain[i].aue_xfer != NULL) { 1882 usbd_free_xfer(sc->aue_cdata.aue_rx_chain[i].aue_xfer); 1883 sc->aue_cdata.aue_rx_chain[i].aue_xfer = NULL; 1884 } 1885 } 1886 1887 /* Free TX resources. */ 1888 for (i = 0; i < AUE_TX_LIST_CNT; i++) { 1889 if (sc->aue_cdata.aue_tx_chain[i].aue_mbuf != NULL) { 1890 m_freem(sc->aue_cdata.aue_tx_chain[i].aue_mbuf); 1891 sc->aue_cdata.aue_tx_chain[i].aue_mbuf = NULL; 1892 } 1893 if (sc->aue_cdata.aue_tx_chain[i].aue_xfer != NULL) { 1894 usbd_free_xfer(sc->aue_cdata.aue_tx_chain[i].aue_xfer); 1895 sc->aue_cdata.aue_tx_chain[i].aue_xfer = NULL; 1896 } 1897 } 1898 1899 sc->aue_link = 0; 1900 1901 ifp->if_flags &= ~(IFF_RUNNING | IFF_OACTIVE); 1902 } 1903 1904 #ifdef __FreeBSD__ 1905 /* 1906 * Stop all chip I/O so that the kernel's probe routines don't 1907 * get confused by errant DMAs when rebooting. 1908 */ 1909 Static void 1910 aue_shutdown(dev) 1911 device_ptr_t dev; 1912 { 1913 struct aue_softc *sc = USBGETSOFTC(dev); 1914 1915 DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); 1916 1917 aue_reset(sc); 1918 aue_stop(sc); 1919 } 1920 #endif 1921
Indexes created Thu Oct 02 07:10:07 GMT 2025