xref: /src/sys/dev/usb/if_smscreg.h

/*	$NetBSD: if_smscreg.h,v 1.3 2013/04/03 15:57:44 skrll Exp $	*/

/*	$OpenBSD: if_smscreg.h,v 1.2 2012/09/27 12:38:11 jsg Exp $	*/
/*-
 * Copyright (c) 2012
 *	Ben Gray <bgray (at) freebsd.org>.
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY AUTHOR AND CONTRIBUTORS ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL AUTHOR OR CONTRIBUTORS BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 * SUCH DAMAGE.
 *
 * $FreeBSD: src/sys/dev/usb/net/if_smscreg.h,v 1.1 2012/08/15 04:03:55 gonzo Exp $
 */
#ifndef _IF_SMSCREG_H_
#define _IF_SMSCREG_H_

/*
 * Definitions for the SMSC LAN9514 and LAN9514 USB to ethernet controllers.
 *
 * This information was gleaned from the SMSC driver in the linux kernel, where
 * it is Copyrighted (C) 2007-2008 SMSC.
 *
 */

/*
 * TRANSMIT FRAMES
 * ---------------
 *   Tx frames are prefixed with an 8-byte header which describes the frame
 *
 *         4 bytes      4 bytes           variable
 *      +------------+------------+--- . . . . . . . . . . . . ---+
 *      | TX_CTRL_0  | TX_CTRL_1  |  Ethernet frame data          |
 *      +------------+------------+--- . . . . . . . . . . . . ---+
 *
 *   Where the headers have the following fields:
 *
 *      TX_CTRL_0 <20:16>  Data offset
 *      TX_CTRL_0 <13>     First segment of frame indicator
 *      TX_CTRL_0 <12>     Last segment of frame indicator
 *      TX_CTRL_0 <10:0>   Buffer size (?)
 *
 *      TX_CTRL_1 <14>     Perform H/W checksuming on IP packets
 *      TX_CTRL_1 <13>     Disable automatic ethernet CRC generation
 *      TX_CTRL_1 <12>     Disable padding (?)
 *      TX_CTRL_1 <10:0>   Packet byte length
 *
 */
#define SMSC_TX_CTRL_0_OFFSET(x)	(((x) & 0x1FUL) << 16)
#define SMSC_TX_CTRL_0_FIRST_SEG	(0x1UL << 13)
#define SMSC_TX_CTRL_0_LAST_SEG		(0x1UL << 12)
#define SMSC_TX_CTRL_0_BUF_SIZE(x)	((x) & 0x000007FFUL)

#define SMSC_TX_CTRL_1_CSUM_ENABLE	(0x1UL << 14)
#define SMSC_TX_CTRL_1_CRC_DISABLE	(0x1UL << 13)
#define SMSC_TX_CTRL_1_PADDING_DISABLE	(0x1UL << 12)
#define SMSC_TX_CTRL_1_PKT_LENGTH(x)	((x) & 0x000007FFUL)

/*
 * RECEIVE FRAMES
 * --------------
 *   Rx frames are prefixed with an 4-byte status header which describes any
 *   errors with the frame as well as things like the length
 *
 *         4 bytes             variable
 *      +------------+--- . . . . . . . . . . . . ---+
 *      |   RX_STAT  |  Ethernet frame data          |
 *      +------------+--- . . . . . . . . . . . . ---+
 *
 *   Where the status header has the following fields:
 *
 *      RX_STAT   <30>     Filter Fail
 *      RX_STAT   <29:16>  Frame Length
 *      RX_STAT   <15>     Error Summary
 *      RX_STAT   <13>     Broadcast Frame
 *      RX_STAT   <12>     Length Error
 *      RX_STAT   <11>     Runt Frame
 *      RX_STAT   <10>     Multicast Frame
 *      RX_STAT   <7>      Frame too long
 *      RX_STAT   <6>      Collision Seen
 *      RX_STAT   <5>      Frame Type
 *      RX_STAT   <4>      Receive Watchdog
 *      RX_STAT   <3>      Mii Error
 *      RX_STAT   <2>      Dribbling
 *      RX_STAT   <1>      CRC Error
 *
 */
#define SMSC_RX_STAT_FILTER_FAIL	(0x1UL << 30)
#define SMSC_RX_STAT_FRM_LENGTH(x)	(((x) >> 16) & 0x3FFFUL)
#define SMSC_RX_STAT_ERROR		(0x1UL << 15)
#define SMSC_RX_STAT_BROADCAST		(0x1UL << 13)
#define SMSC_RX_STAT_LENGTH_ERROR	(0x1UL << 12)
#define SMSC_RX_STAT_RUNT		(0x1UL << 11)
#define SMSC_RX_STAT_MULTICAST		(0x1UL << 10)
#define SMSC_RX_STAT_FRM_TOO_LONG	(0x1UL << 7)
#define SMSC_RX_STAT_COLLISION		(0x1UL << 6)
#define SMSC_RX_STAT_FRM_TYPE		(0x1UL << 5)
#define SMSC_RX_STAT_WATCHDOG		(0x1UL << 4)
#define SMSC_RX_STAT_MII_ERROR		(0x1UL << 3)
#define SMSC_RX_STAT_DRIBBLING		(0x1UL << 2)
#define SMSC_RX_STAT_CRC_ERROR		(0x1UL << 1)

/*
 * REGISTERS
 */
#define SMSC_ID_REV		0x000
#define SMSC_INTR_STATUS	0x008
#define SMSC_RX_CFG		0x00C
#define SMSC_TX_CFG		0x010
#define SMSC_HW_CFG		0x014
#define SMSC_PM_CTRL		0x020
#define SMSC_LED_GPIO_CFG	0x024
#define SMSC_GPIO_CFG		0x028
#define SMSC_AFC_CFG		0x02C
#define SMSC_EEPROM_CMD		0x030
#define SMSC_EEPROM_DATA	0x034
#define SMSC_BURST_CAP		0x038
#define SMSC_GPIO_WAKE		0x064
#define SMSC_INTR_CFG		0x068
#define SMSC_BULK_IN_DLY	0x06C
#define SMSC_MAC_CSR		0x100
#define SMSC_MAC_ADDRH		0x104
#define SMSC_MAC_ADDRL		0x108
#define SMSC_HASHH		0x10C
#define SMSC_HASHL		0x110
#define SMSC_MII_ADDR		0x114
#define SMSC_MII_DATA		0x118
#define SMSC_FLOW		0x11C
#define SMSC_VLAN1		0x120
#define SMSC_VLAN2		0x124
#define SMSC_WUFF		0x128
#define SMSC_WUCSR		0x12C
#define SMSC_COE_CTRL		0x130

/* ID / Revision register */
#define SMSC_ID_REV_CHIP_ID_MASK	0xFFFF0000UL
#define SMSC_ID_REV_CHIP_REV_MASK	0x0000FFFFUL

#define SMSC_RX_FIFO_FLUSH		(0x1UL << 0)

#define SMSC_TX_CFG_ON			(0x1UL << 2)
#define SMSC_TX_CFG_STOP		(0x1UL << 1)
#define SMSC_TX_CFG_FIFO_FLUSH		(0x1UL << 0)

#define SMSC_HW_CFG_BIR			(0x1UL << 12)
#define SMSC_HW_CFG_LEDB		(0x1UL << 11)
#define SMSC_HW_CFG_RXDOFF		(0x3UL << 9)    /* RX pkt alignment */
#define SMSC_HW_CFG_DRP			(0x1UL << 6)
#define SMSC_HW_CFG_MEF			(0x1UL << 5)
#define SMSC_HW_CFG_LRST		(0x1UL << 3)    /* Lite reset */
#define SMSC_HW_CFG_PSEL		(0x1UL << 2)
#define SMSC_HW_CFG_BCE			(0x1UL << 1)
#define SMSC_HW_CFG_SRST		(0x1UL << 0)

#define SMSC_PM_CTRL_PHY_RST		(0x1UL << 4)    /* PHY reset */

#define SMSC_LED_GPIO_CFG_SPD_LED	(0x1UL << 24)
#define SMSC_LED_GPIO_CFG_LNK_LED	(0x1UL << 20)
#define SMSC_LED_GPIO_CFG_FDX_LED	(0x1UL << 16)

/* Hi watermark = 15.5Kb (~10 mtu pkts) */
/* low watermark = 3k (~2 mtu pkts) */
/* backpressure duration = ~ 350us */
/* Apply FC on any frame. */
#define AFC_CFG_DEFAULT			(0x00F830A1)

#define SMSC_EEPROM_CMD_BUSY		(0x1UL << 31)
#define SMSC_EEPROM_CMD_MASK		(0x7UL << 28)
#define SMSC_EEPROM_CMD_READ		(0x0UL << 28)
#define SMSC_EEPROM_CMD_WRITE		(0x3UL << 28)
#define SMSC_EEPROM_CMD_ERASE		(0x5UL << 28)
#define SMSC_EEPROM_CMD_RELOAD		(0x7UL << 28)
#define SMSC_EEPROM_CMD_TIMEOUT		(0x1UL << 10)
#define SMSC_EEPROM_CMD_ADDR_MASK	0x000001FFUL

/* MAC Control and Status Register */
#define SMSC_MAC_CSR_RCVOWN		(0x1UL << 23)  /* Half duplex */
#define SMSC_MAC_CSR_LOOPBK		(0x1UL << 21)  /* Loopback */
#define SMSC_MAC_CSR_FDPX		(0x1UL << 20)  /* Full duplex */
#define SMSC_MAC_CSR_MCPAS		(0x1UL << 19)  /* Multicast mode */
#define SMSC_MAC_CSR_PRMS		(0x1UL << 18)  /* Promiscuous mode */
#define SMSC_MAC_CSR_INVFILT		(0x1UL << 17)  /* Inverse filtering */
#define SMSC_MAC_CSR_PASSBAD		(0x1UL << 16)  /* Pass on bad frames */
#define SMSC_MAC_CSR_HPFILT		(0x1UL << 13)  /* Hash filtering */
#define SMSC_MAC_CSR_BCAST		(0x1UL << 11)  /* Broadcast */
#define SMSC_MAC_CSR_TXEN		(0x1UL << 3)   /* TX enable */
#define SMSC_MAC_CSR_RXEN		(0x1UL << 2)   /* RX enable */

/* Interrupt control register */
#define SMSC_INTR_NTEP			(0x1UL << 31)
#define SMSC_INTR_MACRTO		(0x1UL << 19)
#define SMSC_INTR_TX_STOP		(0x1UL << 17)
#define SMSC_INTR_RX_STOP		(0x1UL << 16)
#define SMSC_INTR_PHY_INT		(0x1UL << 15)
#define SMSC_INTR_TXE			(0x1UL << 14)
#define SMSC_INTR_TDFU			(0x1UL << 13)
#define SMSC_INTR_TDFO			(0x1UL << 12)
#define SMSC_INTR_RXDF			(0x1UL << 11)
#define SMSC_INTR_GPIOS			0x000007FFUL

/* Phy MII interface register */
#define SMSC_MII_WRITE			(0x1UL << 1)
#define SMSC_MII_READ			(0x0UL << 1)
#define SMSC_MII_BUSY			(0x1UL << 0)

/* H/W checksum register */
#define SMSC_COE_CTRL_TX_EN		(0x1UL << 16)  /* Tx H/W csum enable */
#define SMSC_COE_CTRL_RX_MODE		(0x1UL << 1)
#define SMSC_COE_CTRL_RX_EN		(0x1UL << 0)   /* Rx H/W csum enable */

/* Registers on the phy, accessed via MII/MDIO */
#define SMSC_PHY_INTR_STAT		(29)
#define SMSC_PHY_INTR_MASK		(30)

#define SMSC_PHY_INTR_ENERGY_ON		(0x1U << 7)
#define SMSC_PHY_INTR_ANEG_COMP		(0x1U << 6)
#define SMSC_PHY_INTR_REMOTE_FAULT	(0x1U << 5)
#define SMSC_PHY_INTR_LINK_DOWN		(0x1U << 4)

/* USB Vendor Requests */
#define SMSC_UR_WRITE_REG	0xA0
#define SMSC_UR_READ_REG	0xA1
#define SMSC_UR_GET_STATS	0xA2

#define SMSC_RX_LIST_CNT	1
#define SMSC_TX_LIST_CNT	1

#define	SMSC_CONFIG_INDEX	1	/* config number 1 */
#define	SMSC_IFACE_IDX		0

#define SMSC_ENDPT_RX		0
#define SMSC_ENDPT_TX		1
#define SMSC_ENDPT_INTR		2
#define SMSC_ENDPT_MAX		3

#define SMSC_MIN_BUFSZ		2048
#define SMSC_MAX_BUFSZ		18944

#endif  /* _IF_SMSCREG_H_ */