xref: /src/sys/dev/usb/umass.c

/*	$NetBSD: umass.c,v 1.63 2001/10/25 22:43:24 augustss Exp $	*/
/*-
 * Copyright (c) 1999 MAEKAWA Masahide <bishop (at) rr.iij4u.or.jp>,
 *		      Nick Hibma <n_hibma (at) freebsd.org>
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 * SUCH DAMAGE.
 *
 *     $FreeBSD: src/sys/dev/usb/umass.c,v 1.13 2000/03/26 01:39:12 n_hibma Exp $
 */

/*
 * Universal Serial Bus Mass Storage Class specs:
 * http://www.usb.org/developers/data/devclass/usbmassover_11.pdf
 * http://www.usb.org/developers/data/devclass/usbmassbulk_10.pdf
 * http://www.usb.org/developers/data/devclass/usbmass-cbi10.pdf
 * http://www.usb.org/developers/data/devclass/usbmass-ufi10.pdf
 */

/*
 * Ported to NetBSD by Lennart Augustsson <augustss (at) netbsd.org>.
 * Parts of the code written my Jason R. Thorpe <thorpej (at) shagadelic.org>.
 */

/*
 * The driver handles 3 Wire Protocols
 * - Command/Bulk/Interrupt (CBI)
 * - Command/Bulk/Interrupt with Command Completion Interrupt (CBI with CCI)
 * - Mass Storage Bulk-Only (BBB)
 *   (BBB refers Bulk/Bulk/Bulk for Command/Data/Status phases)
 *
 * Over these wire protocols it handles the following command protocols
 * - SCSI
 * - 8070 (ATA/ATAPI for rewritable removable media)
 * - UFI (USB Floppy Interface)
 *
 * 8070i is a transformed version of the SCSI command set. UFI is a transformed
 * version of the 8070i command set.  The sc->transform method is used to
 * convert the commands into the appropriate format (if at all necessary).
 * For example, ATAPI requires all commands to be 12 bytes in length amongst
 * other things.
 *
 * The source code below is marked and can be split into a number of pieces
 * (in this order):
 *
 * - probe/attach/detach
 * - generic transfer routines
 * - BBB
 * - CBI
 * - CBI_I (in addition to functions from CBI)
 * - CAM (Common Access Method)
 * - SCSI
 * - UFI
 * - 8070i
 *
 * The protocols are implemented using a state machine, for the transfers as
 * well as for the resets. The state machine is contained in umass_*_state.
 * The state machine is started through either umass_*_transfer or
 * umass_*_reset.
 *
 * The reason for doing this is a) CAM performs a lot better this way and b) it
 * avoids using tsleep from interrupt context (for example after a failed
 * transfer).
 */

/*
 * The SCSI related part of this driver has been derived from the
 * dev/ppbus/vpo.c driver, by Nicolas Souchu (nsouch (at) freebsd.org).
 *
 * The CAM layer uses so called actions which are messages sent to the host
 * adapter for completion. The actions come in through umass_cam_action. The
 * appropriate block of routines is called depending on the transport protocol
 * in use. When the transfer has finished, these routines call
 * umass_cam_cb again to complete the CAM command.
 */

#include "atapibus.h"

#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/conf.h>
#if defined(__NetBSD__) || defined(__OpenBSD__)
#include <sys/buf.h>
#include <sys/device.h>
#include <sys/ioctl.h>
#include <sys/malloc.h>
#undef KASSERT
#define KASSERT(cond, msg)
#elif defined(__FreeBSD__)
#include <sys/module.h>
#include <sys/bus.h>
#include <machine/clock.h>
#endif

#include <dev/usb/usb.h>
#include <dev/usb/usbdi.h>
#include <dev/usb/usbdi_util.h>
#include <dev/usb/usbdevs.h>

#include <dev/usb/umassbus.h>
#include <dev/usb/umassvar.h>




#ifdef UMASS_DEBUG
int umassdebug = 0;

char *states[TSTATE_STATES+1] = {
	/* should be kept in sync with the list at transfer_state */
	"Idle",
	"BBB CBW",
	"BBB Data",
	"BBB Data bulk-in/-out clear stall",
	"BBB CSW, 1st attempt",
	"BBB CSW bulk-in clear stall",
	"BBB CSW, 2nd attempt",
	"BBB Reset",
	"BBB bulk-in clear stall",
	"BBB bulk-out clear stall",
	"CBI Command",
	"CBI Data",
	"CBI Status",
	"CBI Data bulk-in/-out clear stall",
	"CBI Status intr-in clear stall",
	"CBI Reset",
	"CBI bulk-in clear stall",
	"CBI bulk-out clear stall",
	NULL
};
#endif

/* USB device probe/attach/detach functions */
USB_DECLARE_DRIVER(umass);
Static void umass_disco(struct umass_softc *sc);
Static int umass_match_proto(struct umass_softc *sc,
			     usbd_interface_handle iface,
			     usbd_device_handle dev);
Static void umass_init_shuttle(struct umass_softc *sc);

/* generic transfer functions */
Static usbd_status umass_setup_transfer(struct umass_softc *sc,
				usbd_pipe_handle pipe,
				void *buffer, int buflen, int flags,
				usbd_xfer_handle xfer);
Static usbd_status umass_setup_ctrl_transfer(struct umass_softc *sc,
				usbd_device_handle dev,
				usb_device_request_t *req,
				void *buffer, int buflen, int flags,
				usbd_xfer_handle xfer);
Static void umass_clear_endpoint_stall(struct umass_softc *sc,
				u_int8_t endpt, usbd_pipe_handle pipe,
				int state, usbd_xfer_handle xfer);
#if 0
Static void umass_reset(struct umass_softc *sc,	transfer_cb_f cb, void *priv);
#endif

/* Bulk-Only related functions */
Static void umass_bbb_reset(struct umass_softc *sc, int status);
Static void umass_bbb_transfer(struct umass_softc *sc, int lun,
				void *cmd, int cmdlen,
				void *data, int datalen, int dir,
				transfer_cb_f cb, void *priv);
Static void umass_bbb_state(usbd_xfer_handle xfer,
				usbd_private_handle priv,
				usbd_status err);
usbd_status umass_bbb_get_max_lun(struct umass_softc *sc, u_int8_t *maxlun);


/* CBI related functions */
Static int umass_cbi_adsc(struct umass_softc *sc, char *buffer,int buflen,
				usbd_xfer_handle xfer);
Static void umass_cbi_reset(struct umass_softc *sc, int status);
Static void umass_cbi_transfer(struct umass_softc *sc, int lun,
				void *cmd, int cmdlen,
				void *data, int datalen, int dir,
				transfer_cb_f cb, void *priv);
Static void umass_cbi_state(usbd_xfer_handle xfer,
				usbd_private_handle priv, usbd_status err);

#ifdef UMASS_DEBUG
/* General debugging functions */
Static void umass_bbb_dump_cbw(struct umass_softc *sc,
				umass_bbb_cbw_t *cbw);
Static void umass_bbb_dump_csw(struct umass_softc *sc,
				umass_bbb_csw_t *csw);
Static void umass_dump_buffer(struct umass_softc *sc, u_int8_t *buffer,
				int buflen, int printlen);
#endif


void usbd_clear_endpoint_toggle(usbd_pipe_handle pipe);	/* XXXXX */

/*
 * USB device probe/attach/detach
 */

/*
 * Match the device we are seeing with the devices supported. Fill in the
 * proto and drive fields in the softc accordingly.
 * This function is called from both probe and attach.
 */

Static int
umass_match_proto(struct umass_softc *sc, usbd_interface_handle iface,
		  usbd_device_handle dev)
{
	usb_device_descriptor_t *dd;
	usb_interface_descriptor_t *id;
	u_int vendor, product;

	/*
	 * Fill in sc->drive and sc->proto and return a match
	 * value if both are determined and 0 otherwise.
	 */

	sc->drive = DRIVE_GENERIC;
	sc->transfer_speed = UMASS_DEFAULT_TRANSFER_SPEED;

	sc->sc_udev = dev;
	dd = usbd_get_device_descriptor(dev);
	vendor = UGETW(dd->idVendor);
	product = UGETW(dd->idProduct);

	if (vendor == USB_VENDOR_SHUTTLE &&
	    (product == USB_PRODUCT_SHUTTLE_EUSB ||
	     product == USB_PRODUCT_SHUTTLE_ZIOMMC)
	    ) {
		if (product == USB_PRODUCT_SHUTTLE_EUSB)
			sc->drive = SHUTTLE_EUSB;
#if CBI_I
		sc->wire_proto = WPROTO_CBI_I;
		sc->cmd_proto = CPROTO_ATAPI;
#else
		sc->wire_proto = WPROTO_CBI;
		sc->cmd_proto = CPROTO_ATAPI;
#endif
		sc->subclass = UISUBCLASS_SFF8020I;
		sc->protocol = UIPROTO_MASS_CBI;
		sc->quirks |= NO_TEST_UNIT_READY | NO_START_STOP;
		return (UMATCH_VENDOR_PRODUCT);
	}

	if (vendor == USB_VENDOR_MICROTECH &&
	    product == USB_PRODUCT_MICROTECH_DPCM) {
		sc->wire_proto = WPROTO_CBI;
		sc->cmd_proto = CPROTO_ATAPI;
		sc->subclass = UISUBCLASS_SFF8070I;
		sc->protocol = UIPROTO_MASS_CBI;
		sc->transfer_speed = UMASS_ZIP100_TRANSFER_SPEED * 2;

		return (UMATCH_VENDOR_PRODUCT);
	}

	if (vendor == USB_VENDOR_YANO &&
	    product == USB_PRODUCT_YANO_U640MO) {
#if CBI_I
		sc->wire_proto = WPROTO_CBI_I;
		sc->cmd_proto = CPROTO_ATAPI;
#else
		sc->wire_proto = WPROTO_CBI;
		sc->cmd_proto = CPROTO_ATAPI;
#endif
		sc->quirks |= FORCE_SHORT_INQUIRY;
		return (UMATCH_VENDOR_PRODUCT);
	}

	if (vendor == USB_VENDOR_SONY &&
	    product == USB_PRODUCT_SONY_MSC) {
		sc->quirks |= FORCE_SHORT_INQUIRY;
	}

	if (vendor == USB_VENDOR_YEDATA &&
	    product == USB_PRODUCT_YEDATA_FLASHBUSTERU) {

		/* Revisions < 1.28 do not handle the interrupt endpoint
		 * very well.
		 */
		if (UGETW(dd->bcdDevice) < 0x128) {
			sc->wire_proto = WPROTO_CBI;
			sc->cmd_proto = CPROTO_UFI;
		} else
#if CBI_I
			sc->wire_proto = WPROTO_CBI_I;
			sc->cmd_proto = CPROTO_UFI;
#else
			sc->wire_proto = WPROTO_CBI;
			sc->cmd_proto = CPROTO_UFI;
#endif
		/*
		 * Revisions < 1.28 do not have the TEST UNIT READY command
		 * Revisions == 1.28 have a broken TEST UNIT READY
		 */
		if (UGETW(dd->bcdDevice) <= 0x128)
			sc->quirks |= NO_TEST_UNIT_READY;

		sc->subclass = UISUBCLASS_UFI;
		sc->protocol = UIPROTO_MASS_CBI;

		sc->quirks |= RS_NO_CLEAR_UA;
		sc->transfer_speed = UMASS_FLOPPY_TRANSFER_SPEED;
		return (UMATCH_VENDOR_PRODUCT_REV);
	}

	if (vendor == USB_VENDOR_INSYSTEM &&
	    product == USB_PRODUCT_INSYSTEM_USBCABLE) {
		sc->drive = INSYSTEM_USBCABLE;
		sc->wire_proto = WPROTO_CBI;
		sc->cmd_proto = CPROTO_ATAPI;
		sc->quirks |= NO_TEST_UNIT_READY | NO_START_STOP;
		return (UMATCH_VENDOR_PRODUCT);
	}

	id = usbd_get_interface_descriptor(iface);
	if (id == NULL || id->bInterfaceClass != UICLASS_MASS)
		return (UMATCH_NONE);

	if (vendor == USB_VENDOR_SONY && id->bInterfaceSubClass == 0xff) {
		/*
		 * Sony DSC devices set the sub class to 0xff
		 * instead of 1 (RBC). Fix that here.
		 */
		id->bInterfaceSubClass = UISUBCLASS_RBC;
		/* They also should be able to do higher speed. */
		sc->transfer_speed = 500;
	}

	if (vendor == USB_VENDOR_FUJIPHOTO &&
	    product == USB_PRODUCT_FUJIPHOTO_MASS0100)
		sc->quirks |= NO_TEST_UNIT_READY | NO_START_STOP;

	sc->subclass = id->bInterfaceSubClass;
	sc->protocol = id->bInterfaceProtocol;

	switch (sc->subclass) {
	case UISUBCLASS_SCSI:
		sc->cmd_proto = CPROTO_SCSI;
		break;
	case UISUBCLASS_UFI:
		sc->transfer_speed = UMASS_FLOPPY_TRANSFER_SPEED;
		sc->cmd_proto = CPROTO_UFI;
		break;
	case UISUBCLASS_SFF8020I:
	case UISUBCLASS_SFF8070I:
	case UISUBCLASS_QIC157:
		sc->cmd_proto = CPROTO_ATAPI;
		break;
	case UISUBCLASS_RBC:
		sc->cmd_proto = CPROTO_RBC;
		break;
	default:
		DPRINTF(UDMASS_GEN, ("%s: Unsupported command protocol %d\n",
			USBDEVNAME(sc->sc_dev), id->bInterfaceSubClass));
		return (UMATCH_NONE);
	}

	switch (sc->protocol) {
	case UIPROTO_MASS_CBI:
		sc->wire_proto = WPROTO_CBI;
		break;
	case UIPROTO_MASS_CBI_I:
#if CBI_I
		sc->wire_proto = WPROTO_CBI_I;
#else
		sc->wire_proto = WPROTO_CBI;
#endif
		break;
	case UIPROTO_MASS_BBB:
		sc->wire_proto = WPROTO_BBB;
		break;
	case UIPROTO_MASS_BBB_P:
		sc->drive = ZIP_100;
		sc->wire_proto = WPROTO_BBB;
		sc->transfer_speed = UMASS_ZIP100_TRANSFER_SPEED;
		sc->quirks |= NO_TEST_UNIT_READY;
		break;
	default:
		DPRINTF(UDMASS_GEN, ("%s: Unsupported wire protocol %d\n",
			USBDEVNAME(sc->sc_dev), id->bInterfaceProtocol));
		return (UMATCH_NONE);
	}

	return (UMATCH_DEVCLASS_DEVSUBCLASS_DEVPROTO);
}

USB_MATCH(umass)
{
	USB_MATCH_START(umass, uaa);
#if defined(__FreeBSD__)
	struct umass_softc *sc = device_get_softc(self);
#elif defined(__NetBSD__) || defined(__OpenBSD__)
	struct umass_softc scs, *sc = &scs;
	memset(sc, 0, sizeof *sc);
	strcpy(sc->sc_dev.dv_xname, "umass");
#endif

	if (uaa->iface == NULL)
		return(UMATCH_NONE);

	return (umass_match_proto(sc, uaa->iface, uaa->device));
}

USB_ATTACH(umass)
{
	USB_ATTACH_START(umass, sc, uaa);
	usb_interface_descriptor_t *id;
	usb_endpoint_descriptor_t *ed;
	const char *sSubclass, *sProto;
	char devinfo[1024];
	int i, bno;
	int err;

	/*
	 * the softc struct is bzero-ed in device_set_driver. We can safely
	 * call umass_detach without specifically initialising the struct.
	 */

	usbd_devinfo(uaa->device, 0, devinfo);
	USB_ATTACH_SETUP;

	sc->iface = uaa->iface;
	sc->ifaceno = uaa->ifaceno;

	/* initialise the proto and drive values in the umass_softc (again) */
	if (umass_match_proto(sc, sc->iface, uaa->device) == 0) {
		printf("%s: match failed\n", USBDEVNAME(sc->sc_dev));
		USB_ATTACH_ERROR_RETURN;
	}

	if (sc->drive == INSYSTEM_USBCABLE) {
		err = usbd_set_interface(sc->iface, 1);
		if (err) {
			DPRINTF(UDMASS_USB, ("%s: could not switch to "
					     "Alt Interface %d\n",
					     USBDEVNAME(sc->sc_dev), 1));
			umass_disco(sc);
			USB_ATTACH_ERROR_RETURN;
                }
        }

	/*
	 * The timeout is based on the maximum expected transfer size
	 * divided by the expected transfer speed.
	 * We multiply by 4 to make sure a busy system doesn't make things
	 * fail.
	 */
	sc->timeout = 4 * UMASS_MAX_TRANSFER_SIZE / sc->transfer_speed;
	sc->timeout += UMASS_SPINUP_TIME;	/* allow for spinning up */

	id = usbd_get_interface_descriptor(sc->iface);
	printf("%s: %s\n", USBDEVNAME(sc->sc_dev), devinfo);

	switch (sc->subclass) {
	case UISUBCLASS_RBC:
		sSubclass = "RBC";
		break;
	case UISUBCLASS_SCSI:
		sSubclass = "SCSI";
		break;
	case UISUBCLASS_UFI:
		sSubclass = "UFI";
		break;
	case UISUBCLASS_SFF8020I:
		sSubclass = "SFF8020i";
		break;
	case UISUBCLASS_SFF8070I:
		sSubclass = "SFF8070i";
		break;
	case UISUBCLASS_QIC157:
		sSubclass = "QIC157";
		break;
	default:
		sSubclass = "unknown";
		break;
	}
	switch (sc->protocol) {
	case UIPROTO_MASS_CBI:
		sProto = "CBI";
		break;
	case UIPROTO_MASS_CBI_I:
		sProto = "CBI-I";
		break;
	case UIPROTO_MASS_BBB:
		sProto = "BBB";
		break;
	case UIPROTO_MASS_BBB_P:
		sProto = "BBB-P";
		break;
	default:
		sProto = "unknown";
		break;
	}
	printf("%s: using %s over %s\n", USBDEVNAME(sc->sc_dev), sSubclass,
	       sProto);

	/*
	 * In addition to the Control endpoint the following endpoints
	 * are required:
	 * a) bulk-in endpoint.
	 * b) bulk-out endpoint.
	 * and for Control/Bulk/Interrupt with CCI (CBI_I)
	 * c) intr-in
	 *
	 * The endpoint addresses are not fixed, so we have to read them
	 * from the device descriptors of the current interface.
	 */
	for (i = 0 ; i < id->bNumEndpoints ; i++) {
		ed = usbd_interface2endpoint_descriptor(sc->iface, i);
		if (!ed) {
			printf("%s: could not read endpoint descriptor\n",
			       USBDEVNAME(sc->sc_dev));
			USB_ATTACH_ERROR_RETURN;
		}
		if (UE_GET_DIR(ed->bEndpointAddress) == UE_DIR_IN
		    && (ed->bmAttributes & UE_XFERTYPE) == UE_BULK) {
			sc->bulkin = ed->bEndpointAddress;
		} else if (UE_GET_DIR(ed->bEndpointAddress) == UE_DIR_OUT
		    && (ed->bmAttributes & UE_XFERTYPE) == UE_BULK) {
			sc->bulkout = ed->bEndpointAddress;
		} else if (sc->wire_proto == WPROTO_CBI_I
		    && UE_GET_DIR(ed->bEndpointAddress) == UE_DIR_IN
		    && (ed->bmAttributes & UE_XFERTYPE) == UE_INTERRUPT) {
			sc->intrin = ed->bEndpointAddress;
#ifdef UMASS_DEBUG
			if (UGETW(ed->wMaxPacketSize) > 2) {
				DPRINTF(UDMASS_CBI, ("%s: intr size is %d\n",
					USBDEVNAME(sc->sc_dev),
					UGETW(ed->wMaxPacketSize)));
			}
#endif
		}
	}

	/* check whether we found all the endpoints we need */
	if (!sc->bulkin || !sc->bulkout
	    || (sc->wire_proto == WPROTO_CBI_I && !sc->intrin) ) {
		DPRINTF(UDMASS_USB, ("%s: endpoint not found %d/%d/%d\n",
			USBDEVNAME(sc->sc_dev),
			sc->bulkin, sc->bulkout, sc->intrin));
		umass_disco(sc);
		USB_ATTACH_ERROR_RETURN;
	}

	/*
	 * Get the maximum LUN supported by the device.
	 */
	if (sc->wire_proto == WPROTO_BBB) {
		err = umass_bbb_get_max_lun(sc, &sc->maxlun);
		if (err) {
			printf("%s: unable to get Max Lun: %s\n",
			       USBDEVNAME(sc->sc_dev), usbd_errstr(err));
			USB_ATTACH_ERROR_RETURN;
		}
	} else {
		sc->maxlun = 0;
	}

	/* Open the bulk-in and -out pipe */
	err = usbd_open_pipe(sc->iface, sc->bulkout,
				USBD_EXCLUSIVE_USE, &sc->bulkout_pipe);
	if (err) {
		DPRINTF(UDMASS_USB, ("%s: cannot open %d-out pipe (bulk)\n",
			USBDEVNAME(sc->sc_dev), sc->bulkout));
		umass_disco(sc);
		USB_ATTACH_ERROR_RETURN;
	}
	err = usbd_open_pipe(sc->iface, sc->bulkin,
				USBD_EXCLUSIVE_USE, &sc->bulkin_pipe);
	if (err) {
		DPRINTF(UDMASS_USB, ("%s: could not open %d-in pipe (bulk)\n",
			USBDEVNAME(sc->sc_dev), sc->bulkin));
		umass_disco(sc);
		USB_ATTACH_ERROR_RETURN;
	}
	/*
	 * Open the intr-in pipe if the protocol is CBI with CCI.
	 * Note: early versions of the Zip drive do have an interrupt pipe, but
	 * this pipe is unused
	 *
	 * We do not open the interrupt pipe as an interrupt pipe, but as a
	 * normal bulk endpoint. We send an IN transfer down the wire at the
	 * appropriate time, because we know exactly when to expect data on
	 * that endpoint. This saves bandwidth, but more important, makes the
	 * code for handling the data on that endpoint simpler. No data
	 * arriving concurrently.
	 */
	if (sc->wire_proto == WPROTO_CBI_I) {
		err = usbd_open_pipe(sc->iface, sc->intrin,
				USBD_EXCLUSIVE_USE, &sc->intrin_pipe);
		if (err) {
			DPRINTF(UDMASS_USB, ("%s: couldn't open %d-in (intr)\n",
				USBDEVNAME(sc->sc_dev), sc->intrin));
			umass_disco(sc);
			USB_ATTACH_ERROR_RETURN;
		}
	}

	/* initialisation of generic part */
	sc->transfer_state = TSTATE_IDLE;

	/* request a sufficient number of xfer handles */
	for (i = 0; i < XFER_NR; i++) {
		sc->transfer_xfer[i] = usbd_alloc_xfer(uaa->device);
		if (sc->transfer_xfer[i] == 0) {
			DPRINTF(UDMASS_USB, ("%s: Out of memory\n",
				USBDEVNAME(sc->sc_dev)));
			umass_disco(sc);
			USB_ATTACH_ERROR_RETURN;
		}
	}
	/* Allocate buffer for data transfer (it's huge). */
	switch (sc->wire_proto) {
	case WPROTO_BBB:
		bno = XFER_BBB_DATA;
		goto dalloc;
	case WPROTO_CBI:
		bno = XFER_CBI_DATA;
		goto dalloc;
	case WPROTO_CBI_I:
		bno = XFER_CBI_DATA;
	dalloc:
		sc->data_buffer = usbd_alloc_buffer(sc->transfer_xfer[bno],
						    UMASS_MAX_TRANSFER_SIZE);
		if (sc->data_buffer == NULL) {
			umass_disco(sc);
			USB_ATTACH_ERROR_RETURN;
		}
		break;
	default:
		break;
	}

	/* Initialise the wire protocol specific methods */
	if (sc->wire_proto == WPROTO_BBB) {
		sc->reset = umass_bbb_reset;
		sc->transfer = umass_bbb_transfer;
		sc->state = umass_bbb_state;
	} else if (sc->wire_proto == WPROTO_CBI ||
		   sc->wire_proto == WPROTO_CBI_I) {
		sc->reset = umass_cbi_reset;
		sc->transfer = umass_cbi_transfer;
		sc->state = umass_cbi_state;
#ifdef UMASS_DEBUG
	} else {
		panic("%s:%d: Unknown wire proto 0x%02x\n",
		      __FILE__, __LINE__, sc->wire_proto);
#endif
	}

	if (sc->drive == SHUTTLE_EUSB)
		umass_init_shuttle(sc);

	if (umass_attach_bus(sc)) {
		DPRINTF(UDMASS_GEN, ("%s: bus attach failed\n",
				     USBDEVNAME(sc->sc_dev)));
		umass_disco(sc);
		USB_ATTACH_ERROR_RETURN;
	}

	DPRINTF(UDMASS_GEN, ("%s: Attach finished\n", USBDEVNAME(sc->sc_dev)));

	USB_ATTACH_SUCCESS_RETURN;
}

USB_DETACH(umass)
{
	USB_DETACH_START(umass, sc);
	int rv = 0;

	DPRINTF(UDMASS_USB, ("%s: detached\n", USBDEVNAME(sc->sc_dev)));

	/* Abort the pipes to wake up any waiting processes. */
	if (sc->bulkout_pipe != NULL)
		usbd_abort_pipe(sc->bulkout_pipe);
	if (sc->bulkin_pipe != NULL)
		usbd_abort_pipe(sc->bulkin_pipe);
	if (sc->intrin_pipe != NULL)
		usbd_abort_pipe(sc->intrin_pipe);

#if 0
	/* Do we really need reference counting?  Perhaps in ioctl() */
	s = splusb();
	if (--sc->sc_refcnt >= 0) {
		/* Wait for processes to go away. */
		usb_detach_wait(USBDEV(sc->sc_dev));
	}
	splx(s);
#endif

	rv = umass_detach_bus(sc, flags);

	if (rv != 0)
		return (rv);

	umass_disco(sc);

	usbd_add_drv_event(USB_EVENT_DRIVER_DETACH, sc->sc_udev,
			   USBDEV(sc->sc_dev));

	return (0);
}

Static void
umass_disco(struct umass_softc *sc)
{
	int i;

	DPRINTF(UDMASS_GEN, ("umass_disco\n"));

	/* Free the xfers. */
	for (i = 0; i < XFER_NR; i++)
		if (sc->transfer_xfer[i] != NULL) {
			usbd_free_xfer(sc->transfer_xfer[i]);
			sc->transfer_xfer[i] = NULL;
		}

	/* Remove all the pipes. */
	if (sc->bulkout_pipe != NULL)
		usbd_close_pipe(sc->bulkout_pipe);
	if (sc->bulkin_pipe != NULL)
		usbd_close_pipe(sc->bulkin_pipe);
	if (sc->intrin_pipe != NULL)
		usbd_close_pipe(sc->intrin_pipe);
}

Static void
umass_init_shuttle(struct umass_softc *sc)
{
	usb_device_request_t req;
	u_char status[2];

	/* The Linux driver does this */
	req.bmRequestType = UT_READ_VENDOR_DEVICE;
	req.bRequest = 1;
	USETW(req.wValue, 0);
	USETW(req.wIndex, sc->ifaceno);
	USETW(req.wLength, sizeof status);
	(void)usbd_do_request(sc->sc_udev, &req, &status);
}

/*
 * Generic functions to handle transfers
 */

Static usbd_status
umass_setup_transfer(struct umass_softc *sc, usbd_pipe_handle pipe,
			void *buffer, int buflen, int flags,
			usbd_xfer_handle xfer)
{
	usbd_status err;

	if (sc->sc_dying)
		return (USBD_IOERROR);

	/* Initialiase a USB transfer and then schedule it */

	usbd_setup_xfer(xfer, pipe, (void *)sc, buffer, buflen,
	    flags | sc->sc_xfer_flags, sc->timeout, sc->state);

	err = usbd_transfer(xfer);
	DPRINTF(UDMASS_XFER,("%s: start xfer buffer=%p buflen=%d flags=0x%x "
	    "timeout=%d\n", USBDEVNAME(sc->sc_dev),
	    buffer, buflen, flags | sc->sc_xfer_flags, sc->timeout));
	if (err && err != USBD_IN_PROGRESS) {
		DPRINTF(UDMASS_BBB, ("%s: failed to setup transfer, %s\n",
			USBDEVNAME(sc->sc_dev), usbd_errstr(err)));
		return (err);
	}

	return (USBD_NORMAL_COMPLETION);
}


Static usbd_status
umass_setup_ctrl_transfer(struct umass_softc *sc, usbd_device_handle dev,
	 usb_device_request_t *req,
	 void *buffer, int buflen, int flags,
	 usbd_xfer_handle xfer)
{
	usbd_status err;

	if (sc->sc_dying)
		return (USBD_IOERROR);

	/* Initialiase a USB control transfer and then schedule it */

	usbd_setup_default_xfer(xfer, dev, (void *) sc,
	    sc->timeout, req, buffer, buflen, flags, sc->state);

	err = usbd_transfer(xfer);
	if (err && err != USBD_IN_PROGRESS) {
		DPRINTF(UDMASS_BBB, ("%s: failed to setup ctrl transfer, %s\n",
			 USBDEVNAME(sc->sc_dev), usbd_errstr(err)));

		/* do not reset, as this would make us loop */
		return (err);
	}

	return (USBD_NORMAL_COMPLETION);
}

Static void
umass_clear_endpoint_stall(struct umass_softc *sc,
	u_int8_t endpt, usbd_pipe_handle pipe,
	int state, usbd_xfer_handle xfer)
{
	usbd_device_handle dev;

	if (sc->sc_dying)
		return;

	DPRINTF(UDMASS_BBB, ("%s: Clear endpoint 0x%02x stall\n",
		USBDEVNAME(sc->sc_dev), endpt));

	usbd_interface2device_handle(sc->iface, &dev);

	sc->transfer_state = state;

	usbd_clear_endpoint_toggle(pipe);

	sc->request.bmRequestType = UT_WRITE_ENDPOINT;
	sc->request.bRequest = UR_CLEAR_FEATURE;
	USETW(sc->request.wValue, UF_ENDPOINT_HALT);
	USETW(sc->request.wIndex, endpt);
	USETW(sc->request.wLength, 0);
	umass_setup_ctrl_transfer(sc, dev, &sc->request, NULL, 0, 0, xfer);
}

#if 0
Static void
umass_reset(struct umass_softc *sc, transfer_cb_f cb, void *priv)
{
	sc->transfer_cb = cb;
	sc->transfer_priv = priv;

	/* The reset is a forced reset, so no error (yet) */
	sc->reset(sc, STATUS_CMD_OK);
}
#endif

/*
 * Bulk protocol specific functions
 */

Static void
umass_bbb_reset(struct umass_softc *sc, int status)
{
	usbd_device_handle dev;

	KASSERT(sc->proto & PROTO_BBB,
		("sc->proto == 0x%02x wrong for umass_bbb_reset\n", sc->proto));

	if (sc->sc_dying)
		return;

	/*
	 * Reset recovery (5.3.4 in Universal Serial Bus Mass Storage Class)
	 *
	 * For Reset Recovery the host shall issue in the following order:
	 * a) a Bulk-Only Mass Storage Reset
	 * b) a Clear Feature HALT to the Bulk-In endpoint
	 * c) a Clear Feature HALT to the Bulk-Out endpoint
	 *
	 * This is done in 3 steps, states:
	 * TSTATE_BBB_RESET1
	 * TSTATE_BBB_RESET2
	 * TSTATE_BBB_RESET3
	 *
	 * If the reset doesn't succeed, the device should be port reset.
	 */

	DPRINTF(UDMASS_BBB, ("%s: Bulk Reset\n",
		USBDEVNAME(sc->sc_dev)));

	sc->transfer_state = TSTATE_BBB_RESET1;
	sc->transfer_status = status;

	usbd_interface2device_handle(sc->iface, &dev);

	/* reset is a class specific interface write */
	sc->request.bmRequestType = UT_WRITE_CLASS_INTERFACE;
	sc->request.bRequest = UR_BBB_RESET;
	USETW(sc->request.wValue, 0);
	USETW(sc->request.wIndex, sc->ifaceno);
	USETW(sc->request.wLength, 0);
	umass_setup_ctrl_transfer(sc, dev, &sc->request, NULL, 0, 0,
				  sc->transfer_xfer[XFER_BBB_RESET1]);
}

Static void
umass_bbb_transfer(struct umass_softc *sc, int lun, void *cmd, int cmdlen,
		    void *data, int datalen, int dir,
		    transfer_cb_f cb, void *priv)
{
	static int dCBWtag = 42;	/* unique for CBW of transfer */

	DPRINTF(UDMASS_BBB,("%s: umass_bbb_transfer cmd=0x%02x\n",
		USBDEVNAME(sc->sc_dev), *(u_char*)cmd));

	KASSERT(sc->proto & PROTO_BBB,
		("sc->proto == 0x%02x wrong for umass_bbb_transfer\n",
		sc->proto));

	/*
	 * Do a Bulk-Only transfer with cmdlen bytes from cmd, possibly
	 * a data phase of datalen bytes from/to the device and finally a
	 * csw read phase.
	 * If the data direction was inbound a maximum of datalen bytes
	 * is stored in the buffer pointed to by data.
	 *
	 * umass_bbb_transfer initialises the transfer and lets the state
	 * machine in umass_bbb_state handle the completion. It uses the
	 * following states:
	 * TSTATE_BBB_COMMAND
	 *   -> TSTATE_BBB_DATA
	 *   -> TSTATE_BBB_STATUS
	 *   -> TSTATE_BBB_STATUS2
	 *   -> TSTATE_BBB_IDLE
	 *
	 * An error in any of those states will invoke
	 * umass_bbb_reset.
	 */

	/* check the given arguments */
	KASSERT(datalen == 0 || data != NULL,
		("%s: datalen > 0, but no buffer",USBDEVNAME(sc->sc_dev)));
	KASSERT(cmdlen <= CBWCDBLENGTH,
		("%s: cmdlen exceeds CDB length in CBW (%d > %d)",
			USBDEVNAME(sc->sc_dev), cmdlen, CBWCDBLENGTH));
	KASSERT(dir == DIR_NONE || datalen > 0,
		("%s: datalen == 0 while direction is not NONE\n",
			USBDEVNAME(sc->sc_dev)));
	KASSERT(datalen == 0 || dir != DIR_NONE,
		("%s: direction is NONE while datalen is not zero\n",
			USBDEVNAME(sc->sc_dev)));
	KASSERT(sizeof(umass_bbb_cbw_t) == UMASS_BBB_CBW_SIZE,
		("%s: CBW struct does not have the right size (%d vs. %d)\n",
			USBDEVNAME(sc->sc_dev),
			sizeof(umass_bbb_cbw_t), UMASS_BBB_CBW_SIZE));
	KASSERT(sizeof(umass_bbb_csw_t) == UMASS_BBB_CSW_SIZE,
		("%s: CSW struct does not have the right size (%d vs. %d)\n",
			USBDEVNAME(sc->sc_dev),
			sizeof(umass_bbb_csw_t), UMASS_BBB_CSW_SIZE));

	/*
	 * Determine the direction of the data transfer and the length.
	 *
	 * dCBWDataTransferLength (datalen) :
	 *   This field indicates the number of bytes of data that the host
	 *   intends to transfer on the IN or OUT Bulk endpoint(as indicated by
	 *   the Direction bit) during the execution of this command. If this
	 *   field is set to 0, the device will expect that no data will be
	 *   transferred IN or OUT during this command, regardless of the value
	 *   of the Direction bit defined in dCBWFlags.
	 *
	 * dCBWFlags (dir) :
	 *   The bits of the Flags field are defined as follows:
	 *     Bits 0-6	 reserved
	 *     Bit  7	 Direction - this bit shall be ignored if the
	 *			     dCBWDataTransferLength field is zero.
	 *		 0 = data Out from host to device
	 *		 1 = data In from device to host
	 */

	/* Fill in the Command Block Wrapper */
	USETDW(sc->cbw.dCBWSignature, CBWSIGNATURE);
	USETDW(sc->cbw.dCBWTag, dCBWtag);
	dCBWtag++;	/* cannot be done in macro (it will be done 4 times) */
	USETDW(sc->cbw.dCBWDataTransferLength, datalen);
	/* DIR_NONE is treated as DIR_OUT (0x00) */
	sc->cbw.bCBWFlags = (dir == DIR_IN? CBWFLAGS_IN:CBWFLAGS_OUT);
	sc->cbw.bCBWLUN = lun;
	sc->cbw.bCDBLength = cmdlen;
	bcopy(cmd, sc->cbw.CBWCDB, cmdlen);

	DIF(UDMASS_BBB, umass_bbb_dump_cbw(sc, &sc->cbw));

	/* store the details for the data transfer phase */
	sc->transfer_dir = dir;
	sc->transfer_data = data;
	sc->transfer_datalen = datalen;
	sc->transfer_actlen = 0;
	sc->transfer_cb = cb;
	sc->transfer_priv = priv;
	sc->transfer_status = STATUS_CMD_OK;

	/* move from idle to the command state */
	sc->transfer_state = TSTATE_BBB_COMMAND;

	/* Send the CBW from host to device via bulk-out endpoint. */
	if (umass_setup_transfer(sc, sc->bulkout_pipe,
			&sc->cbw, UMASS_BBB_CBW_SIZE, 0,
			sc->transfer_xfer[XFER_BBB_CBW])) {
		umass_bbb_reset(sc, STATUS_WIRE_FAILED);
	}
}


Static void
umass_bbb_state(usbd_xfer_handle xfer, usbd_private_handle priv,
		usbd_status err)
{
	struct umass_softc *sc = (struct umass_softc *) priv;
	usbd_xfer_handle next_xfer;

	KASSERT(sc->proto & PROTO_BBB,
		("sc->proto == 0x%02x wrong for umass_bbb_state\n",sc->proto));

	if (sc->sc_dying)
		return;

	/*
	 * State handling for BBB transfers.
	 *
	 * The subroutine is rather long. It steps through the states given in
	 * Annex A of the Bulk-Only specification.
	 * Each state first does the error handling of the previous transfer
	 * and then prepares the next transfer.
	 * Each transfer is done asynchroneously so after the request/transfer
	 * has been submitted you will find a 'return;'.
	 */

	DPRINTF(UDMASS_BBB, ("%s: Handling BBB state %d (%s), xfer=%p, %s\n",
		USBDEVNAME(sc->sc_dev), sc->transfer_state,
		states[sc->transfer_state], xfer, usbd_errstr(err)));

	switch (sc->transfer_state) {

	/***** Bulk Transfer *****/
	case TSTATE_BBB_COMMAND:
		/* Command transport phase, error handling */
		if (err) {
			DPRINTF(UDMASS_BBB, ("%s: failed to send CBW\n",
				USBDEVNAME(sc->sc_dev)));
			/* If the device detects that the CBW is invalid, then
			 * the device may STALL both bulk endpoints and require
			 * a Bulk-Reset
			 */
			umass_bbb_reset(sc, STATUS_WIRE_FAILED);
			return;
		}

		/* Data transport phase, setup transfer */
		sc->transfer_state = TSTATE_BBB_DATA;
		if (sc->transfer_dir == DIR_IN) {
			if (umass_setup_transfer(sc, sc->bulkin_pipe,
					sc->data_buffer, sc->transfer_datalen,
					USBD_SHORT_XFER_OK | USBD_NO_COPY,
					sc->transfer_xfer[XFER_BBB_DATA]))
				umass_bbb_reset(sc, STATUS_WIRE_FAILED);

			return;
		} else if (sc->transfer_dir == DIR_OUT) {
			memcpy(sc->data_buffer, sc->transfer_data,
			       sc->transfer_datalen);
			if (umass_setup_transfer(sc, sc->bulkout_pipe,
					sc->data_buffer, sc->transfer_datalen,
					USBD_NO_COPY,/* fixed length transfer */
					sc->transfer_xfer[XFER_BBB_DATA]))
				umass_bbb_reset(sc, STATUS_WIRE_FAILED);

			return;
		} else {
			DPRINTF(UDMASS_BBB, ("%s: no data phase\n",
				USBDEVNAME(sc->sc_dev)));
		}

		/* FALLTHROUGH if no data phase, err == 0 */
	case TSTATE_BBB_DATA:
		/* Command transport phase, error handling (ignored if no data
		 * phase (fallthrough from previous state)) */
		if (sc->transfer_dir != DIR_NONE) {
			/* retrieve the length of the transfer that was done */
			usbd_get_xfer_status(xfer, NULL, NULL,
					     &sc->transfer_actlen, NULL);

			if (err) {
				DPRINTF(UDMASS_BBB, ("%s: Data-%s %db failed, "
					"%s\n", USBDEVNAME(sc->sc_dev),
					(sc->transfer_dir == DIR_IN?"in":"out"),
					sc->transfer_datalen,usbd_errstr(err)));

				if (err == USBD_STALLED) {
					umass_clear_endpoint_stall(sc,
					  (sc->transfer_dir == DIR_IN?
					    sc->bulkin:sc->bulkout),
					  (sc->transfer_dir == DIR_IN?
					    sc->bulkin_pipe:sc->bulkout_pipe),
					  TSTATE_BBB_DCLEAR,
					  sc->transfer_xfer[XFER_BBB_DCLEAR]);
					return;
				} else {
					/* Unless the error is a pipe stall the
					 * error is fatal.
					 */
					umass_bbb_reset(sc,STATUS_WIRE_FAILED);
					return;
				}
			}
		}

		if (sc->transfer_dir == DIR_IN)
			memcpy(sc->transfer_data, sc->data_buffer,
			       sc->transfer_actlen);

		DIF(UDMASS_BBB, if (sc->transfer_dir == DIR_IN)
					umass_dump_buffer(sc, sc->transfer_data,
						sc->transfer_datalen, 48));

		/* FALLTHROUGH, err == 0 (no data phase or successfull) */
	case TSTATE_BBB_DCLEAR: /* stall clear after data phase */
	case TSTATE_BBB_SCLEAR: /* stall clear after status phase */
		/* Reading of CSW after bulk stall condition in data phase
		 * (TSTATE_BBB_DATA2) or bulk-in stall condition after
		 * reading CSW (TSTATE_BBB_SCLEAR).
		 * In the case of no data phase or successfull data phase,
		 * err == 0 and the following if block is passed.
		 */
		if (err) {	/* should not occur */
			/* try the transfer below, even if clear stall failed */
			DPRINTF(UDMASS_BBB, ("%s: bulk-%s stall clear failed"
				", %s\n", USBDEVNAME(sc->sc_dev),
				(sc->transfer_dir == DIR_IN? "in":"out"),
				usbd_errstr(err)));
			umass_bbb_reset(sc, STATUS_WIRE_FAILED);
			return;
		}

		/* Status transport phase, setup transfer */
		if (sc->transfer_state == TSTATE_BBB_COMMAND ||
		    sc->transfer_state == TSTATE_BBB_DATA ||
		    sc->transfer_state == TSTATE_BBB_DCLEAR) {
			/* After no data phase, successfull data phase and
			 * after clearing bulk-in/-out stall condition
			 */
			sc->transfer_state = TSTATE_BBB_STATUS1;
			next_xfer = sc->transfer_xfer[XFER_BBB_CSW1];
		} else {
			/* After first attempt of fetching CSW */
			sc->transfer_state = TSTATE_BBB_STATUS2;
			next_xfer = sc->transfer_xfer[XFER_BBB_CSW2];
		}

		/* Read the Command Status Wrapper via bulk-in endpoint. */
		if (umass_setup_transfer(sc, sc->bulkin_pipe,
				&sc->csw, UMASS_BBB_CSW_SIZE, 0,
				next_xfer)) {
			umass_bbb_reset(sc, STATUS_WIRE_FAILED);
			return;
		}

		return;
	case TSTATE_BBB_STATUS1:	/* first attempt */
	case TSTATE_BBB_STATUS2:	/* second attempt */
		/* Status transfer, error handling */
		if (err) {
			DPRINTF(UDMASS_BBB, ("%s: Failed to read CSW, %s%s\n",
				USBDEVNAME(sc->sc_dev), usbd_errstr(err),
				(sc->transfer_state == TSTATE_BBB_STATUS1?
					", retrying":"")));

			/* If this was the first attempt at fetching the CSW
			 * retry it, otherwise fail.
			 */
			if (sc->transfer_state == TSTATE_BBB_STATUS1) {
				umass_clear_endpoint_stall(sc,
						sc->bulkin, sc->bulkin_pipe,
						TSTATE_BBB_SCLEAR,
						sc->transfer_xfer[XFER_BBB_SCLEAR]);
				return;
			} else {
				umass_bbb_reset(sc, STATUS_WIRE_FAILED);
				return;
			}
		}

		DIF(UDMASS_BBB, umass_bbb_dump_csw(sc, &sc->csw));

		/* Check CSW and handle any error */
		if (UGETDW(sc->csw.dCSWSignature) != CSWSIGNATURE) {
			/* Invalid CSW: Wrong signature or wrong tag might
			 * indicate that the device is confused -> reset it.
			 */
			printf("%s: Invalid CSW: sig 0x%08x should be 0x%08x\n",
				USBDEVNAME(sc->sc_dev),
				UGETDW(sc->csw.dCSWSignature),
				CSWSIGNATURE);

			umass_bbb_reset(sc, STATUS_WIRE_FAILED);
			return;
		} else if (UGETDW(sc->csw.dCSWTag)
				!= UGETDW(sc->cbw.dCBWTag)) {
			printf("%s: Invalid CSW: tag %d should be %d\n",
				USBDEVNAME(sc->sc_dev),
				UGETDW(sc->csw.dCSWTag),
				UGETDW(sc->cbw.dCBWTag));

			umass_bbb_reset(sc, STATUS_WIRE_FAILED);
			return;

		/* CSW is valid here */
		} else if (sc->csw.bCSWStatus > CSWSTATUS_PHASE) {
			printf("%s: Invalid CSW: status %d > %d\n",
				USBDEVNAME(sc->sc_dev),
				sc->csw.bCSWStatus,
				CSWSTATUS_PHASE);

			umass_bbb_reset(sc, STATUS_WIRE_FAILED);
			return;
		} else if (sc->csw.bCSWStatus == CSWSTATUS_PHASE) {
			printf("%s: Phase Error, residue = %d\n",
				USBDEVNAME(sc->sc_dev),
				UGETDW(sc->csw.dCSWDataResidue));

			umass_bbb_reset(sc, STATUS_WIRE_FAILED);
			return;

		} else if (sc->transfer_actlen > sc->transfer_datalen) {
			/* Buffer overrun! Don't let this go by unnoticed */
			panic("%s: transferred %d bytes instead of %d bytes\n",
				USBDEVNAME(sc->sc_dev),
				sc->transfer_actlen, sc->transfer_datalen);
#if 0
		} else if (sc->transfer_datalen - sc->transfer_actlen
			   != UGETDW(sc->csw.dCSWDataResidue)) {
			DPRINTF(UDMASS_BBB, ("%s: actlen=%d != residue=%d\n",
				USBDEVNAME(sc->sc_dev),
				sc->transfer_datalen - sc->transfer_actlen,
				UGETDW(sc->csw.dCSWDataResidue)));

			umass_bbb_reset(sc, STATUS_WIRE_FAILED);
			return;
#endif
		} else if (sc->csw.bCSWStatus == CSWSTATUS_FAILED) {
			DPRINTF(UDMASS_BBB, ("%s: Command Failed, res = %d\n",
				USBDEVNAME(sc->sc_dev),
				UGETDW(sc->csw.dCSWDataResidue)));

			/* SCSI command failed but transfer was succesful */
			sc->transfer_state = TSTATE_IDLE;
			sc->transfer_cb(sc, sc->transfer_priv,
					UGETDW(sc->csw.dCSWDataResidue),
					STATUS_CMD_FAILED);

			return;

		} else {	/* success */
			sc->transfer_state = TSTATE_IDLE;
			sc->transfer_cb(sc, sc->transfer_priv,
					UGETDW(sc->csw.dCSWDataResidue),
					STATUS_CMD_OK);

			return;
		}

	/***** Bulk Reset *****/
	case TSTATE_BBB_RESET1:
		if (err)
			printf("%s: BBB reset failed, %s\n",
				USBDEVNAME(sc->sc_dev), usbd_errstr(err));

		umass_clear_endpoint_stall(sc,
			sc->bulkin, sc->bulkin_pipe, TSTATE_BBB_RESET2,
			sc->transfer_xfer[XFER_BBB_RESET2]);

		return;
	case TSTATE_BBB_RESET2:
		if (err)	/* should not occur */
			printf("%s: BBB bulk-in clear stall failed, %s\n",
			       USBDEVNAME(sc->sc_dev), usbd_errstr(err));
			/* no error recovery, otherwise we end up in a loop */

		umass_clear_endpoint_stall(sc,
			sc->bulkout, sc->bulkout_pipe, TSTATE_BBB_RESET3,
			sc->transfer_xfer[XFER_BBB_RESET3]);

		return;
	case TSTATE_BBB_RESET3:
		if (err)	/* should not occur */
			printf("%s: BBB bulk-out clear stall failed, %s\n",
			       USBDEVNAME(sc->sc_dev), usbd_errstr(err));
			/* no error recovery, otherwise we end up in a loop */

		sc->transfer_state = TSTATE_IDLE;
		if (sc->transfer_priv) {
			sc->transfer_cb(sc, sc->transfer_priv,
					sc->transfer_datalen,
					sc->transfer_status);
		}

		return;

	/***** Default *****/
	default:
		panic("%s: Unknown state %d\n",
		      USBDEVNAME(sc->sc_dev), sc->transfer_state);
	}
}

/*
 * Command/Bulk/Interrupt (CBI) specific functions
 */

Static int
umass_cbi_adsc(struct umass_softc *sc, char *buffer, int buflen,
	       usbd_xfer_handle xfer)
{
	usbd_device_handle dev;

	KASSERT(sc->proto & (PROTO_CBI|PROTO_CBI_I),
		("sc->proto == 0x%02x wrong for umass_cbi_adsc\n",sc->proto));

	usbd_interface2device_handle(sc->iface, &dev);

	sc->request.bmRequestType = UT_WRITE_CLASS_INTERFACE;
	sc->request.bRequest = UR_CBI_ADSC;
	USETW(sc->request.wValue, 0);
	USETW(sc->request.wIndex, sc->ifaceno);
	USETW(sc->request.wLength, buflen);
	return umass_setup_ctrl_transfer(sc, dev, &sc->request, buffer,
					 buflen, 0, xfer);
}


Static void
umass_cbi_reset(struct umass_softc *sc, int status)
{
	int i;
#	define SEND_DIAGNOSTIC_CMDLEN	12

	KASSERT(sc->proto & (PROTO_CBI|PROTO_CBI_I),
		("sc->proto == 0x%02x wrong for umass_cbi_reset\n",sc->proto));

	if (sc->sc_dying)
		return;

	/*
	 * Command Block Reset Protocol
	 *
	 * First send a reset request to the device. Then clear
	 * any possibly stalled bulk endpoints.

	 * This is done in 3 steps, states:
	 * TSTATE_CBI_RESET1
	 * TSTATE_CBI_RESET2
	 * TSTATE_CBI_RESET3
	 *
	 * If the reset doesn't succeed, the device should be port reset.
	 */

	DPRINTF(UDMASS_CBI, ("%s: CBI Reset\n",
		USBDEVNAME(sc->sc_dev)));

	KASSERT(sizeof(sc->cbl) >= SEND_DIAGNOSTIC_CMDLEN,
		("%s: CBL struct is too small (%d < %d)\n",
			USBDEVNAME(sc->sc_dev),
			sizeof(sc->cbl), SEND_DIAGNOSTIC_CMDLEN));

	sc->transfer_state = TSTATE_CBI_RESET1;
	sc->transfer_status = status;

	/* The 0x1d code is the SEND DIAGNOSTIC command. To distingiush between
	 * the two the last 10 bytes of the cbl is filled with 0xff (section
	 * 2.2 of the CBI spec).
	 */
	sc->cbl[0] = 0x1d;	/* Command Block Reset */
	sc->cbl[1] = 0x04;
	for (i = 2; i < SEND_DIAGNOSTIC_CMDLEN; i++)
		sc->cbl[i] = 0xff;

	umass_cbi_adsc(sc, sc->cbl, SEND_DIAGNOSTIC_CMDLEN,
		       sc->transfer_xfer[XFER_CBI_RESET1]);
	/* XXX if the command fails we should reset the port on the bub */
}

Static void
umass_cbi_transfer(struct umass_softc *sc, int lun,
		void *cmd, int cmdlen, void *data, int datalen, int dir,
		transfer_cb_f cb, void *priv)
{
	DPRINTF(UDMASS_CBI,("%s: umass_cbi_transfer cmd=0x%02x, len=%d\n",
		USBDEVNAME(sc->sc_dev), *(u_char*)cmd, datalen));

	KASSERT(sc->proto & (PROTO_CBI|PROTO_CBI_I),
		("sc->proto == 0x%02x wrong for umass_cbi_transfer\n",
		sc->proto));

	if (sc->sc_dying)
		return;

	/*
	 * Do a CBI transfer with cmdlen bytes from cmd, possibly
	 * a data phase of datalen bytes from/to the device and finally a
	 * csw read phase.
	 * If the data direction was inbound a maximum of datalen bytes
	 * is stored in the buffer pointed to by data.
	 *
	 * umass_cbi_transfer initialises the transfer and lets the state
	 * machine in umass_cbi_state handle the completion. It uses the
	 * following states:
	 * TSTATE_CBI_COMMAND
	 *   -> XXX fill in
	 *
	 * An error in any of those states will invoke
	 * umass_cbi_reset.
	 */

	/* check the given arguments */
	KASSERT(datalen == 0 || data != NULL,
		("%s: datalen > 0, but no buffer",USBDEVNAME(sc->sc_dev)));
	KASSERT(datalen == 0 || dir != DIR_NONE,
		("%s: direction is NONE while datalen is not zero\n",
			USBDEVNAME(sc->sc_dev)));

	/* store the details for the data transfer phase */
	sc->transfer_dir = dir;
	sc->transfer_data = data;
	sc->transfer_datalen = datalen;
	sc->transfer_actlen = 0;
	sc->transfer_cb = cb;
	sc->transfer_priv = priv;
	sc->transfer_status = STATUS_CMD_OK;

	/* move from idle to the command state */
	sc->transfer_state = TSTATE_CBI_COMMAND;

	/* Send the Command Block from host to device via control endpoint. */
	if (umass_cbi_adsc(sc, cmd, cmdlen, sc->transfer_xfer[XFER_CBI_CB]))
		umass_cbi_reset(sc, STATUS_WIRE_FAILED);
}

Static void
umass_cbi_state(usbd_xfer_handle xfer, usbd_private_handle priv,
		usbd_status err)
{
	struct umass_softc *sc = (struct umass_softc *) priv;

	KASSERT(sc->proto & (PROTO_CBI|PROTO_CBI_I),
		("sc->proto == 0x%02x wrong for umass_cbi_state\n", sc->proto));

	if (sc->sc_dying)
		return;

	/*
	 * State handling for CBI transfers.
	 */

	DPRINTF(UDMASS_CBI, ("%s: Handling CBI state %d (%s), xfer=%p, %s\n",
		USBDEVNAME(sc->sc_dev), sc->transfer_state,
		states[sc->transfer_state], xfer, usbd_errstr(err)));

	switch (sc->transfer_state) {

	/***** CBI Transfer *****/
	case TSTATE_CBI_COMMAND:
		if (err == USBD_STALLED) {
			DPRINTF(UDMASS_CBI, ("%s: Command Transport failed\n",
				USBDEVNAME(sc->sc_dev)));
			/* Status transport by control pipe (section 2.3.2.1).
			 * The command contained in the command block failed.
			 *
			 * The control pipe has already been unstalled by the
			 * USB stack.
			 * Section 2.4.3.1.1 states that the bulk in endpoints
			 * should not stalled at this point.
			 */

			sc->transfer_state = TSTATE_IDLE;
			sc->transfer_cb(sc, sc->transfer_priv,
					sc->transfer_datalen,
					STATUS_CMD_FAILED);

			return;
		} else if (err) {
			DPRINTF(UDMASS_CBI, ("%s: failed to send ADSC\n",
				USBDEVNAME(sc->sc_dev)));
			umass_cbi_reset(sc, STATUS_WIRE_FAILED);

			return;
		}

		sc->transfer_state = TSTATE_CBI_DATA;
		if (sc->transfer_dir == DIR_IN) {
			if (umass_setup_transfer(sc, sc->bulkin_pipe,
					sc->transfer_data, sc->transfer_datalen,
					USBD_SHORT_XFER_OK | USBD_NO_COPY,
					sc->transfer_xfer[XFER_CBI_DATA]))
				umass_cbi_reset(sc, STATUS_WIRE_FAILED);

		} else if (sc->transfer_dir == DIR_OUT) {
			memcpy(sc->data_buffer, sc->transfer_data,
			       sc->transfer_datalen);
			if (umass_setup_transfer(sc, sc->bulkout_pipe,
					sc->transfer_data, sc->transfer_datalen,
					USBD_NO_COPY,/* fixed length transfer */
					sc->transfer_xfer[XFER_CBI_DATA]))
				umass_cbi_reset(sc, STATUS_WIRE_FAILED);

		} else if (sc->wire_proto == WPROTO_CBI_I) {
			DPRINTF(UDMASS_CBI, ("%s: no data phase\n",
				USBDEVNAME(sc->sc_dev)));
			sc->transfer_state = TSTATE_CBI_STATUS;
			if (umass_setup_transfer(sc, sc->intrin_pipe,
					&sc->sbl, sizeof(sc->sbl),
					0,	/* fixed length transfer */
					sc->transfer_xfer[XFER_CBI_STATUS])){
				umass_cbi_reset(sc, STATUS_WIRE_FAILED);
			}
		} else {
			DPRINTF(UDMASS_CBI, ("%s: no data phase\n",
				USBDEVNAME(sc->sc_dev)));
			/* No command completion interrupt. Request
			 * sense data.
			 */
			sc->transfer_state = TSTATE_IDLE;
			sc->transfer_cb(sc, sc->transfer_priv,
			       0, STATUS_CMD_UNKNOWN);
		}

		return;

	case TSTATE_CBI_DATA:
		/* retrieve the length of the transfer that was done */
		usbd_get_xfer_status(xfer,NULL,NULL,&sc->transfer_actlen,NULL);
		DPRINTF(UDMASS_CBI, ("%s: CBI_DATA actlen=%d\n",
			USBDEVNAME(sc->sc_dev), sc->transfer_actlen));

		if (err) {
			DPRINTF(UDMASS_CBI, ("%s: Data-%s %db failed, "
				"%s\n", USBDEVNAME(sc->sc_dev),
				(sc->transfer_dir == DIR_IN?"in":"out"),
				sc->transfer_datalen,usbd_errstr(err)));

			if (err == USBD_STALLED) {
				umass_clear_endpoint_stall(sc,
					sc->bulkin, sc->bulkin_pipe,
					TSTATE_CBI_DCLEAR,
					sc->transfer_xfer[XFER_CBI_DCLEAR]);
			} else {
				umass_cbi_reset(sc, STATUS_WIRE_FAILED);
			}
			return;
		}

		if (sc->transfer_dir == DIR_IN)
			memcpy(sc->transfer_data, sc->data_buffer,
			       sc->transfer_actlen);

		DIF(UDMASS_CBI, if (sc->transfer_dir == DIR_IN)
					umass_dump_buffer(sc, sc->transfer_data,
						sc->transfer_actlen, 48));

		if (sc->wire_proto == WPROTO_CBI_I) {
			sc->transfer_state = TSTATE_CBI_STATUS;
			memset(&sc->sbl, 0, sizeof(sc->sbl));
			if (umass_setup_transfer(sc, sc->intrin_pipe,
				    &sc->sbl, sizeof(sc->sbl),
				    0,	/* fixed length transfer */
				    sc->transfer_xfer[XFER_CBI_STATUS])){
				umass_cbi_reset(sc, STATUS_WIRE_FAILED);
			}
		} else {
			/* No command completion interrupt. Request
			 * sense to get status of command.
			 */
			sc->transfer_state = TSTATE_IDLE;
			sc->transfer_cb(sc, sc->transfer_priv,
				sc->transfer_datalen - sc->transfer_actlen,
				STATUS_CMD_UNKNOWN);
		}
		return;

	case TSTATE_CBI_STATUS:
		if (err) {
			DPRINTF(UDMASS_CBI, ("%s: Status Transport failed\n",
				USBDEVNAME(sc->sc_dev)));
			/* Status transport by interrupt pipe (section 2.3.2.2).
			 */

			if (err == USBD_STALLED) {
				umass_clear_endpoint_stall(sc,
					sc->intrin, sc->intrin_pipe,
					TSTATE_CBI_SCLEAR,
					sc->transfer_xfer[XFER_CBI_SCLEAR]);
			} else {
				umass_cbi_reset(sc, STATUS_WIRE_FAILED);
			}
			return;
		}

		/* Dissect the information in the buffer */

		if (sc->cmd_proto == CPROTO_UFI) {
			int status;

			/* Section 3.4.3.1.3 specifies that the UFI command
			 * protocol returns an ASC and ASCQ in the interrupt
			 * data block.
			 */

			DPRINTF(UDMASS_CBI, ("%s: UFI CCI, ASC = 0x%02x, "
				"ASCQ = 0x%02x\n",
				USBDEVNAME(sc->sc_dev),
				sc->sbl.ufi.asc, sc->sbl.ufi.ascq));

			if (sc->sbl.ufi.asc == 0 && sc->sbl.ufi.ascq == 0)
				status = STATUS_CMD_OK;
			else
				status = STATUS_CMD_FAILED;

			/* No sense, command successfull */
		} else {
			/* Command Interrupt Data Block */
			DPRINTF(UDMASS_CBI, ("%s: type=0x%02x, value=0x%02x\n",
				USBDEVNAME(sc->sc_dev),
				sc->sbl.common.type, sc->sbl.common.value));

			if (sc->sbl.common.type == IDB_TYPE_CCI) {
				int err;

				if ((sc->sbl.common.value&IDB_VALUE_STATUS_MASK)
							== IDB_VALUE_PASS) {
					err = STATUS_CMD_OK;
				} else if ((sc->sbl.common.value & IDB_VALUE_STATUS_MASK)
							== IDB_VALUE_FAIL ||
					   (sc->sbl.common.value & IDB_VALUE_STATUS_MASK)
						== IDB_VALUE_PERSISTENT) {
					err = STATUS_CMD_FAILED;
				} else {
					err = STATUS_WIRE_FAILED;
				}

				sc->transfer_state = TSTATE_IDLE;
				sc->transfer_cb(sc, sc->transfer_priv,
						sc->transfer_datalen,
						err);
			}
		}
		return;

	case TSTATE_CBI_DCLEAR:
		if (err) {	/* should not occur */
			printf("%s: CBI bulk-in/out stall clear failed, %s\n",
			       USBDEVNAME(sc->sc_dev), usbd_errstr(err));
			umass_cbi_reset(sc, STATUS_WIRE_FAILED);
		}

		sc->transfer_state = TSTATE_IDLE;
		sc->transfer_cb(sc, sc->transfer_priv,
				sc->transfer_datalen,
				STATUS_CMD_FAILED);
		return;

	case TSTATE_CBI_SCLEAR:
		if (err)	/* should not occur */
			printf("%s: CBI intr-in stall clear failed, %s\n",
			       USBDEVNAME(sc->sc_dev), usbd_errstr(err));

		/* Something really bad is going on. Reset the device */
		umass_cbi_reset(sc, STATUS_CMD_FAILED);
		return;

	/***** CBI Reset *****/
	case TSTATE_CBI_RESET1:
		if (err)
			printf("%s: CBI reset failed, %s\n",
				USBDEVNAME(sc->sc_dev), usbd_errstr(err));

		umass_clear_endpoint_stall(sc,
			sc->bulkin, sc->bulkin_pipe, TSTATE_CBI_RESET2,
			sc->transfer_xfer[XFER_CBI_RESET2]);

		return;
	case TSTATE_CBI_RESET2:
		if (err)	/* should not occur */
			printf("%s: CBI bulk-in stall clear failed, %s\n",
			       USBDEVNAME(sc->sc_dev), usbd_errstr(err));
			/* no error recovery, otherwise we end up in a loop */

		umass_clear_endpoint_stall(sc,
			sc->bulkout, sc->bulkout_pipe, TSTATE_CBI_RESET3,
			sc->transfer_xfer[XFER_CBI_RESET3]);

		return;
	case TSTATE_CBI_RESET3:
		if (err)	/* should not occur */
			printf("%s: CBI bulk-out stall clear failed, %s\n",
			       USBDEVNAME(sc->sc_dev), usbd_errstr(err));
			/* no error recovery, otherwise we end up in a loop */

		sc->transfer_state = TSTATE_IDLE;
		if (sc->transfer_priv) {
			sc->transfer_cb(sc, sc->transfer_priv,
					sc->transfer_datalen,
					sc->transfer_status);
		}

		return;


	/***** Default *****/
	default:
		panic("%s: Unknown state %d\n",
		      USBDEVNAME(sc->sc_dev), sc->transfer_state);
	}
}

usbd_status
umass_bbb_get_max_lun(struct umass_softc *sc, u_int8_t *maxlun)
{
	usbd_device_handle dev;
	usb_device_request_t req;
	usbd_status err;
	usb_interface_descriptor_t *id;

	*maxlun = 0;		/* Default to 0. */

	DPRINTF(UDMASS_BBB, ("%s: Get Max Lun\n", USBDEVNAME(sc->sc_dev)));

	usbd_interface2device_handle(sc->iface, &dev);
	id = usbd_get_interface_descriptor(sc->iface);

	/* The Get Max Lun command is a class-specific request. */
	req.bmRequestType = UT_READ_CLASS_INTERFACE;
	req.bRequest = UR_BBB_GET_MAX_LUN;
	USETW(req.wValue, 0);
	USETW(req.wIndex, id->bInterfaceNumber);
	USETW(req.wLength, 1);

	err = usbd_do_request(dev, &req, maxlun);
	switch (err) {
	case USBD_NORMAL_COMPLETION:
		DPRINTF(UDMASS_BBB, ("%s: Max Lun %d\n",
		    USBDEVNAME(sc->sc_dev), *maxlun));
		break;

	case USBD_STALLED:
		/*
		 * Device doesn't support Get Max Lun request.
		 */
		err = USBD_NORMAL_COMPLETION;
		DPRINTF(UDMASS_BBB, ("%s: Get Max Lun not supported\n",
		    USBDEVNAME(sc->sc_dev)));
		break;

	case USBD_SHORT_XFER:
		/*
		 * XXX This must mean Get Max Lun is not supported, too!
		 */
		err = USBD_NORMAL_COMPLETION;
		DPRINTF(UDMASS_BBB, ("%s: Get Max Lun SHORT_XFER\n",
		    USBDEVNAME(sc->sc_dev)));
		break;

	default:
		printf("%s: Get Max Lun failed: %s\n",
		    USBDEVNAME(sc->sc_dev), usbd_errstr(err));
		/* XXX Should we port_reset the device? */
		break;
	}

	return (err);
}




#ifdef UMASS_DEBUG
Static void
umass_bbb_dump_cbw(struct umass_softc *sc, umass_bbb_cbw_t *cbw)
{
	int clen = cbw->bCDBLength;
	int dlen = UGETDW(cbw->dCBWDataTransferLength);
	u_int8_t *c = cbw->CBWCDB;
	int tag = UGETDW(cbw->dCBWTag);
	int flags = cbw->bCBWFlags;

	DPRINTF(UDMASS_BBB, ("%s: CBW %d: cmdlen = %db "
		"(0x%02x%02x%02x%02x%02x%02x%s), "
		"data = %d bytes, dir = %s\n",
		USBDEVNAME(sc->sc_dev), tag, clen,
		c[0], c[1], c[2], c[3], c[4], c[5], (clen > 6? "...":""),
		dlen, (flags == CBWFLAGS_IN? "in":
		       (flags == CBWFLAGS_OUT? "out":"<invalid>"))));
}

Static void
umass_bbb_dump_csw(struct umass_softc *sc, umass_bbb_csw_t *csw)
{
	int sig = UGETDW(csw->dCSWSignature);
	int tag = UGETW(csw->dCSWTag);
	int res = UGETDW(csw->dCSWDataResidue);
	int status = csw->bCSWStatus;

	DPRINTF(UDMASS_BBB, ("%s: CSW %d: sig = 0x%08x (%s), tag = %d, "
		"res = %d, status = 0x%02x (%s)\n", USBDEVNAME(sc->sc_dev),
		tag, sig, (sig == CSWSIGNATURE?	 "valid":"invalid"),
		tag, res,
		status, (status == CSWSTATUS_GOOD? "good":
			 (status == CSWSTATUS_FAILED? "failed":
			  (status == CSWSTATUS_PHASE? "phase":"<invalid>")))));
}

Static void
umass_dump_buffer(struct umass_softc *sc, u_int8_t *buffer, int buflen,
		  int printlen)
{
	int i, j;
	char s1[40];
	char s2[40];
	char s3[5];

	s1[0] = '\0';
	s3[0] = '\0';

	sprintf(s2, " buffer=%p, buflen=%d", buffer, buflen);
	for (i = 0; i < buflen && i < printlen; i++) {
		j = i % 16;
		if (j == 0 && i != 0) {
			DPRINTF(UDMASS_GEN, ("%s: 0x %s%s\n",
				USBDEVNAME(sc->sc_dev), s1, s2));
			s2[0] = '\0';
		}
		sprintf(&s1[j*2], "%02x", buffer[i] & 0xff);
	}
	if (buflen > printlen)
		sprintf(s3, " ...");
	DPRINTF(UDMASS_GEN, ("%s: 0x %s%s%s\n",
		USBDEVNAME(sc->sc_dev), s1, s2, s3));
}
#endif